Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / drivers / net / ethernet / freescale / Kconfig

diff --git a/kernel/drivers/net/ethernet/freescale/Kconfig b/kernel/drivers/net/ethernet/freescale/Kconfig
new file mode 100644 (file)
index 0000000..25e3425
--- /dev/null
+++ b/kernel/drivers/net/ethernet/freescale/Kconfig
@@ -0,0 +1,96 @@
+#
+# Freescale device configuration
+#
+
+config NET_VENDOR_FREESCALE
+       bool "Freescale devices"
+       default y
+       depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
+                  M523x || M527x || M5272 || M528x || M520x || M532x || \
+                  ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
+       ---help---
+         If you have a network (Ethernet) card belonging to this class, say Y
+         and read the Ethernet-HOWTO, available from
+         <http://www.tldp.org/docs.html#howto>.
+
+         Note that the answer to this question doesn't directly affect the
+         kernel: saying N will just cause the configurator to skip all
+         the questions about Freescale devices. If you say Y, you will be
+         asked for your specific card in the following questions.
+
+if NET_VENDOR_FREESCALE
+
+config FEC
+       tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+       depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
+                  ARCH_MXC || SOC_IMX28)
+       default ARCH_MXC || SOC_IMX28 if ARM
+       select PHYLIB
+       select PTP_1588_CLOCK
+       ---help---
+         Say Y here if you want to use the built-in 10/100 Fast ethernet
+         controller on some Motorola ColdFire and Freescale i.MX processors.
+
+config FEC_MPC52xx
+       tristate "FEC MPC52xx driver"
+       depends on PPC_MPC52xx && PPC_BESTCOMM
+       select CRC32
+       select PHYLIB
+       select PPC_BESTCOMM_FEC
+       ---help---
+         This option enables support for the MPC5200's on-chip
+         Fast Ethernet Controller
+         If compiled as module, it will be called fec_mpc52xx.
+
+config FEC_MPC52xx_MDIO
+       bool "FEC MPC52xx MDIO bus driver"
+       depends on FEC_MPC52xx
+       default y
+       ---help---
+         The MPC5200's FEC can connect to the Ethernet either with
+         an external MII PHY chip or 10 Mbps 7-wire interface
+         (Motorola? industry standard).
+         If your board uses an external PHY connected to FEC, enable this.
+         If not sure, enable.
+         If compiled as module, it will be called fec_mpc52xx_phy.
+
+source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
+
+config FSL_PQ_MDIO
+       tristate "Freescale PQ MDIO"
+       select PHYLIB
+       ---help---
+         This driver supports the MDIO bus used by the gianfar and UCC drivers.
+
+config FSL_XGMAC_MDIO
+       tristate "Freescale XGMAC MDIO"
+       select PHYLIB
+       select OF_MDIO
+       ---help---
+         This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
+         on the FMan mEMAC (which supports both Clauses 22 and 45)
+
+config UCC_GETH
+       tristate "Freescale QE Gigabit Ethernet"
+       depends on QUICC_ENGINE
+       select FSL_PQ_MDIO
+       select PHYLIB
+       ---help---
+         This driver supports the Gigabit Ethernet mode of the QUICC Engine,
+         which is available on some Freescale SOCs.
+
+config UGETH_TX_ON_DEMAND
+       bool "Transmit on Demand support"
+       depends on UCC_GETH
+
+config GIANFAR
+       tristate "Gianfar Ethernet"
+       depends on FSL_SOC
+       select FSL_PQ_MDIO
+       select PHYLIB
+       select CRC32
+       ---help---
+         This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
+         and MPC86xx family of chips, and the FEC on the 8540.
+
+endif # NET_VENDOR_FREESCALE