--- /dev/null
+/* bnx2x_reg.h: Broadcom Everest network driver.
+ *
+ * Copyright (c) 2007-2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation.
+ *
+ * The registers description starts with the register Access type followed
+ * by size in bits. For example [RW 32]. The access types are:
+ * R - Read only
+ * RC - Clear on read
+ * RW - Read/Write
+ * ST - Statistics register (clear on read)
+ * W - Write only
+ * WB - Wide bus register - the size is over 32 bits and it should be
+ * read/write in consecutive 32 bits accesses
+ * WR - Write Clear (write 1 to clear the bit)
+ *
+ */
+#ifndef BNX2X_REG_H
+#define BNX2X_REG_H
+
+#define ATC_ATC_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define ATC_ATC_INT_STS_REG_ATC_GPA_MULTIPLE_HITS (0x1<<2)
+#define ATC_ATC_INT_STS_REG_ATC_IREQ_LESS_THAN_STU (0x1<<5)
+#define ATC_ATC_INT_STS_REG_ATC_RCPL_TO_EMPTY_CNT (0x1<<3)
+#define ATC_ATC_INT_STS_REG_ATC_TCPL_ERROR (0x1<<4)
+#define ATC_ATC_INT_STS_REG_ATC_TCPL_TO_NOT_PEND (0x1<<1)
+/* [RW 1] Initiate the ATC array - reset all the valid bits */
+#define ATC_REG_ATC_INIT_ARRAY 0x1100b8
+/* [R 1] ATC initialization done */
+#define ATC_REG_ATC_INIT_DONE 0x1100bc
+/* [RC 6] Interrupt register #0 read clear */
+#define ATC_REG_ATC_INT_STS_CLR 0x1101c0
+/* [RW 5] Parity mask register #0 read/write */
+#define ATC_REG_ATC_PRTY_MASK 0x1101d8
+/* [R 5] Parity register #0 read */
+#define ATC_REG_ATC_PRTY_STS 0x1101cc
+/* [RC 5] Parity register #0 read clear */
+#define ATC_REG_ATC_PRTY_STS_CLR 0x1101d0
+/* [RW 19] Interrupt mask register #0 read/write */
+#define BRB1_REG_BRB1_INT_MASK 0x60128
+/* [R 19] Interrupt register #0 read */
+#define BRB1_REG_BRB1_INT_STS 0x6011c
+/* [RW 4] Parity mask register #0 read/write */
+#define BRB1_REG_BRB1_PRTY_MASK 0x60138
+/* [R 4] Parity register #0 read */
+#define BRB1_REG_BRB1_PRTY_STS 0x6012c
+/* [RC 4] Parity register #0 read clear */
+#define BRB1_REG_BRB1_PRTY_STS_CLR 0x60130
+/* [RW 10] At address BRB1_IND_FREE_LIST_PRS_CRDT initialize free head. At
+ * address BRB1_IND_FREE_LIST_PRS_CRDT+1 initialize free tail. At address
+ * BRB1_IND_FREE_LIST_PRS_CRDT+2 initialize parser initial credit. Warning -
+ * following reset the first rbc access to this reg must be write; there can
+ * be no more rbc writes after the first one; there can be any number of rbc
+ * read following the first write; rbc access not following these rules will
+ * result in hang condition. */
+#define BRB1_REG_FREE_LIST_PRS_CRDT 0x60200
+/* [RW 10] The number of free blocks below which the full signal to class 0
+ * is asserted */
+#define BRB1_REG_FULL_0_XOFF_THRESHOLD_0 0x601d0
+#define BRB1_REG_FULL_0_XOFF_THRESHOLD_1 0x60230
+/* [RW 11] The number of free blocks above which the full signal to class 0
+ * is de-asserted */
+#define BRB1_REG_FULL_0_XON_THRESHOLD_0 0x601d4
+#define BRB1_REG_FULL_0_XON_THRESHOLD_1 0x60234
+/* [RW 11] The number of free blocks below which the full signal to class 1
+ * is asserted */
+#define BRB1_REG_FULL_1_XOFF_THRESHOLD_0 0x601d8
+#define BRB1_REG_FULL_1_XOFF_THRESHOLD_1 0x60238
+/* [RW 11] The number of free blocks above which the full signal to class 1
+ * is de-asserted */
+#define BRB1_REG_FULL_1_XON_THRESHOLD_0 0x601dc
+#define BRB1_REG_FULL_1_XON_THRESHOLD_1 0x6023c
+/* [RW 11] The number of free blocks below which the full signal to the LB
+ * port is asserted */
+#define BRB1_REG_FULL_LB_XOFF_THRESHOLD 0x601e0
+/* [RW 10] The number of free blocks above which the full signal to the LB
+ * port is de-asserted */
+#define BRB1_REG_FULL_LB_XON_THRESHOLD 0x601e4
+/* [RW 10] The number of free blocks above which the High_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_HIGH_LLFC_HIGH_THRESHOLD_0 0x6014c
+/* [RW 10] The number of free blocks below which the High_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_HIGH_LLFC_LOW_THRESHOLD_0 0x6013c
+/* [RW 11] The number of blocks guarantied for the LB port */
+#define BRB1_REG_LB_GUARANTIED 0x601ec
+/* [RW 11] The hysteresis on the guarantied buffer space for the Lb port
+ * before signaling XON. */
+#define BRB1_REG_LB_GUARANTIED_HYST 0x60264
+/* [RW 24] LL RAM data. */
+#define BRB1_REG_LL_RAM 0x61000
+/* [RW 10] The number of free blocks above which the Low_llfc signal to
+ interface #n is de-asserted. */
+#define BRB1_REG_LOW_LLFC_HIGH_THRESHOLD_0 0x6016c
+/* [RW 10] The number of free blocks below which the Low_llfc signal to
+ interface #n is asserted. */
+#define BRB1_REG_LOW_LLFC_LOW_THRESHOLD_0 0x6015c
+/* [RW 11] The number of blocks guarantied for class 0 in MAC 0. The
+ * register is applicable only when per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_0_CLASS_0_GUARANTIED 0x60244
+/* [RW 11] The hysteresis on the guarantied buffer space for class 0 in MAC
+ * 1 before signaling XON. The register is applicable only when
+ * per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_0_CLASS_0_GUARANTIED_HYST 0x60254
+/* [RW 11] The number of blocks guarantied for class 1 in MAC 0. The
+ * register is applicable only when per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_0_CLASS_1_GUARANTIED 0x60248
+/* [RW 11] The hysteresis on the guarantied buffer space for class 1in MAC 0
+ * before signaling XON. The register is applicable only when
+ * per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_0_CLASS_1_GUARANTIED_HYST 0x60258
+/* [RW 11] The number of blocks guarantied for class 0in MAC1.The register
+ * is applicable only when per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_1_CLASS_0_GUARANTIED 0x6024c
+/* [RW 11] The hysteresis on the guarantied buffer space for class 0 in MAC
+ * 1 before signaling XON. The register is applicable only when
+ * per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_1_CLASS_0_GUARANTIED_HYST 0x6025c
+/* [RW 11] The number of blocks guarantied for class 1 in MAC 1. The
+ * register is applicable only when per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_1_CLASS_1_GUARANTIED 0x60250
+/* [RW 11] The hysteresis on the guarantied buffer space for class 1 in MAC
+ * 1 before signaling XON. The register is applicable only when
+ * per_class_guaranty_mode is set. */
+#define BRB1_REG_MAC_1_CLASS_1_GUARANTIED_HYST 0x60260
+/* [RW 11] The number of blocks guarantied for the MAC port. The register is
+ * applicable only when per_class_guaranty_mode is reset. */
+#define BRB1_REG_MAC_GUARANTIED_0 0x601e8
+#define BRB1_REG_MAC_GUARANTIED_1 0x60240
+/* [R 24] The number of full blocks. */
+#define BRB1_REG_NUM_OF_FULL_BLOCKS 0x60090
+/* [ST 32] The number of cycles that the write_full signal towards MAC #0
+ was asserted. */
+#define BRB1_REG_NUM_OF_FULL_CYCLES_0 0x600c8
+#define BRB1_REG_NUM_OF_FULL_CYCLES_1 0x600cc
+#define BRB1_REG_NUM_OF_FULL_CYCLES_4 0x600d8
+/* [ST 32] The number of cycles that the pause signal towards MAC #0 was
+ asserted. */
+#define BRB1_REG_NUM_OF_PAUSE_CYCLES_0 0x600b8
+#define BRB1_REG_NUM_OF_PAUSE_CYCLES_1 0x600bc
+/* [RW 10] The number of free blocks below which the pause signal to class 0
+ * is asserted */
+#define BRB1_REG_PAUSE_0_XOFF_THRESHOLD_0 0x601c0
+#define BRB1_REG_PAUSE_0_XOFF_THRESHOLD_1 0x60220
+/* [RW 11] The number of free blocks above which the pause signal to class 0
+ * is de-asserted */
+#define BRB1_REG_PAUSE_0_XON_THRESHOLD_0 0x601c4
+#define BRB1_REG_PAUSE_0_XON_THRESHOLD_1 0x60224
+/* [RW 11] The number of free blocks below which the pause signal to class 1
+ * is asserted */
+#define BRB1_REG_PAUSE_1_XOFF_THRESHOLD_0 0x601c8
+#define BRB1_REG_PAUSE_1_XOFF_THRESHOLD_1 0x60228
+/* [RW 11] The number of free blocks above which the pause signal to class 1
+ * is de-asserted */
+#define BRB1_REG_PAUSE_1_XON_THRESHOLD_0 0x601cc
+#define BRB1_REG_PAUSE_1_XON_THRESHOLD_1 0x6022c
+/* [RW 10] Write client 0: De-assert pause threshold. Not Functional */
+#define BRB1_REG_PAUSE_HIGH_THRESHOLD_0 0x60078
+#define BRB1_REG_PAUSE_HIGH_THRESHOLD_1 0x6007c
+/* [RW 10] Write client 0: Assert pause threshold. */
+#define BRB1_REG_PAUSE_LOW_THRESHOLD_0 0x60068
+/* [RW 1] Indicates if to use per-class guaranty mode (new mode) or per-MAC
+ * guaranty mode (backwards-compatible mode). 0=per-MAC guaranty mode (BC
+ * mode). 1=per-class guaranty mode (new mode). */
+#define BRB1_REG_PER_CLASS_GUARANTY_MODE 0x60268
+/* [R 24] The number of full blocks occpied by port. */
+#define BRB1_REG_PORT_NUM_OCC_BLOCKS_0 0x60094
+/* [RW 1] Reset the design by software. */
+#define BRB1_REG_SOFT_RESET 0x600dc
+/* [R 5] Used to read the value of the XX protection CAM occupancy counter. */
+#define CCM_REG_CAM_OCCUP 0xd0188
+/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CCM_CFC_IFEN 0xd003c
+/* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CCM_CQM_IFEN 0xd000c
+/* [RW 1] If set the Q index; received from the QM is inserted to event ID.
+ Otherwise 0 is inserted. */
+#define CCM_REG_CCM_CQM_USE_Q 0xd00c0
+/* [RW 11] Interrupt mask register #0 read/write */
+#define CCM_REG_CCM_INT_MASK 0xd01e4
+/* [R 11] Interrupt register #0 read */
+#define CCM_REG_CCM_INT_STS 0xd01d8
+/* [RW 27] Parity mask register #0 read/write */
+#define CCM_REG_CCM_PRTY_MASK 0xd01f4
+/* [R 27] Parity register #0 read */
+#define CCM_REG_CCM_PRTY_STS 0xd01e8
+/* [RC 27] Parity register #0 read clear */
+#define CCM_REG_CCM_PRTY_STS_CLR 0xd01ec
+/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
+ REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
+ Is used to determine the number of the AG context REG-pairs written back;
+ when the input message Reg1WbFlg isn't set. */
+#define CCM_REG_CCM_REG0_SZ 0xd00c4
+/* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CCM_STORM0_IFEN 0xd0004
+/* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CCM_STORM1_IFEN 0xd0008
+/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define CCM_REG_CDU_AG_RD_IFEN 0xd0030
+/* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input
+ are disregarded; all other signals are treated as usual; if 1 - normal
+ activity. */
+#define CCM_REG_CDU_AG_WR_IFEN 0xd002c
+/* [RW 1] CDU STORM read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define CCM_REG_CDU_SM_RD_IFEN 0xd0038
+/* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid
+ input is disregarded; all other signals are treated as usual; if 1 -
+ normal activity. */
+#define CCM_REG_CDU_SM_WR_IFEN 0xd0034
+/* [RW 4] CFC output initial credit. Max credit available - 15.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 1 at start-up. */
+#define CCM_REG_CFC_INIT_CRD 0xd0204
+/* [RW 2] Auxiliary counter flag Q number 1. */
+#define CCM_REG_CNT_AUX1_Q 0xd00c8
+/* [RW 2] Auxiliary counter flag Q number 2. */
+#define CCM_REG_CNT_AUX2_Q 0xd00cc
+/* [RW 28] The CM header value for QM request (primary). */
+#define CCM_REG_CQM_CCM_HDR_P 0xd008c
+/* [RW 28] The CM header value for QM request (secondary). */
+#define CCM_REG_CQM_CCM_HDR_S 0xd0090
+/* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CQM_CCM_IFEN 0xd0014
+/* [RW 6] QM output initial credit. Max credit available - 32. Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 32 at start-up. */
+#define CCM_REG_CQM_INIT_CRD 0xd020c
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CQM_P_WEIGHT 0xd00b8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CQM_S_WEIGHT 0xd00bc
+/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_CSDM_IFEN 0xd0018
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the SDM interface is detected. */
+#define CCM_REG_CSDM_LENGTH_MIS 0xd0170
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_CSDM_WEIGHT 0xd00b4
+/* [RW 28] The CM header for QM formatting in case of an error in the QM
+ inputs. */
+#define CCM_REG_ERR_CCM_HDR 0xd0094
+/* [RW 8] The Event ID in case the input message ErrorFlg is set. */
+#define CCM_REG_ERR_EVNT_ID 0xd0098
+/* [RW 8] FIC0 output initial credit. Max credit available - 255. Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define CCM_REG_FIC0_INIT_CRD 0xd0210
+/* [RW 8] FIC1 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define CCM_REG_FIC1_INIT_CRD 0xd0214
+/* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1
+ - strict priority defined by ~ccm_registers_gr_ag_pr.gr_ag_pr;
+ ~ccm_registers_gr_ld0_pr.gr_ld0_pr and
+ ~ccm_registers_gr_ld1_pr.gr_ld1_pr. Groups are according to channels and
+ outputs to STORM: aggregation; load FIC0; load FIC1 and store. */
+#define CCM_REG_GR_ARB_TYPE 0xd015c
+/* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed; that the Store channel priority is
+ the compliment to 4 of the rest priorities - Aggregation channel; Load
+ (FIC0) channel and Load (FIC1). */
+#define CCM_REG_GR_LD0_PR 0xd0164
+/* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed; that the Store channel priority is
+ the compliment to 4 of the rest priorities - Aggregation channel; Load
+ (FIC0) channel and Load (FIC1). */
+#define CCM_REG_GR_LD1_PR 0xd0168
+/* [RW 2] General flags index. */
+#define CCM_REG_INV_DONE_Q 0xd0108
+/* [RW 4] The number of double REG-pairs(128 bits); loaded from the STORM
+ context and sent to STORM; for a specific connection type. The double
+ REG-pairs are used in order to align to STORM context row size of 128
+ bits. The offset of these data in the STORM context is always 0. Index
+ _(0..15) stands for the connection type (one of 16). */
+#define CCM_REG_N_SM_CTX_LD_0 0xd004c
+#define CCM_REG_N_SM_CTX_LD_1 0xd0050
+#define CCM_REG_N_SM_CTX_LD_2 0xd0054
+#define CCM_REG_N_SM_CTX_LD_3 0xd0058
+#define CCM_REG_N_SM_CTX_LD_4 0xd005c
+/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define CCM_REG_PBF_IFEN 0xd0028
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the pbf interface is detected. */
+#define CCM_REG_PBF_LENGTH_MIS 0xd0180
+/* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_PBF_WEIGHT 0xd00ac
+#define CCM_REG_PHYS_QNUM1_0 0xd0134
+#define CCM_REG_PHYS_QNUM1_1 0xd0138
+#define CCM_REG_PHYS_QNUM2_0 0xd013c
+#define CCM_REG_PHYS_QNUM2_1 0xd0140
+#define CCM_REG_PHYS_QNUM3_0 0xd0144
+#define CCM_REG_PHYS_QNUM3_1 0xd0148
+#define CCM_REG_QOS_PHYS_QNUM0_0 0xd0114
+#define CCM_REG_QOS_PHYS_QNUM0_1 0xd0118
+#define CCM_REG_QOS_PHYS_QNUM1_0 0xd011c
+#define CCM_REG_QOS_PHYS_QNUM1_1 0xd0120
+#define CCM_REG_QOS_PHYS_QNUM2_0 0xd0124
+#define CCM_REG_QOS_PHYS_QNUM2_1 0xd0128
+#define CCM_REG_QOS_PHYS_QNUM3_0 0xd012c
+#define CCM_REG_QOS_PHYS_QNUM3_1 0xd0130
+/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define CCM_REG_STORM_CCM_IFEN 0xd0010
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the STORM interface is detected. */
+#define CCM_REG_STORM_LENGTH_MIS 0xd016c
+/* [RW 3] The weight of the STORM input in the WRR (Weighted Round robin)
+ mechanism. 0 stands for weight 8 (the most prioritised); 1 stands for
+ weight 1(least prioritised); 2 stands for weight 2 (more prioritised);
+ tc. */
+#define CCM_REG_STORM_WEIGHT 0xd009c
+/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define CCM_REG_TSEM_IFEN 0xd001c
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the tsem interface is detected. */
+#define CCM_REG_TSEM_LENGTH_MIS 0xd0174
+/* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_TSEM_WEIGHT 0xd00a0
+/* [RW 1] Input usem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define CCM_REG_USEM_IFEN 0xd0024
+/* [RC 1] Set when message length mismatch (relative to last indication) at
+ the usem interface is detected. */
+#define CCM_REG_USEM_LENGTH_MIS 0xd017c
+/* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_USEM_WEIGHT 0xd00a8
+/* [RW 1] Input xsem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define CCM_REG_XSEM_IFEN 0xd0020
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the xsem interface is detected. */
+#define CCM_REG_XSEM_LENGTH_MIS 0xd0178
+/* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define CCM_REG_XSEM_WEIGHT 0xd00a4
+/* [RW 19] Indirect access to the descriptor table of the XX protection
+ mechanism. The fields are: [5:0] - message length; [12:6] - message
+ pointer; 18:13] - next pointer. */
+#define CCM_REG_XX_DESCR_TABLE 0xd0300
+#define CCM_REG_XX_DESCR_TABLE_SIZE 24
+/* [R 7] Used to read the value of XX protection Free counter. */
+#define CCM_REG_XX_FREE 0xd0184
+/* [RW 6] Initial value for the credit counter; responsible for fulfilling
+ of the Input Stage XX protection buffer by the XX protection pending
+ messages. Max credit available - 127. Write writes the initial credit
+ value; read returns the current value of the credit counter. Must be
+ initialized to maximum XX protected message size - 2 at start-up. */
+#define CCM_REG_XX_INIT_CRD 0xd0220
+/* [RW 7] The maximum number of pending messages; which may be stored in XX
+ protection. At read the ~ccm_registers_xx_free.xx_free counter is read.
+ At write comprises the start value of the ~ccm_registers_xx_free.xx_free
+ counter. */
+#define CCM_REG_XX_MSG_NUM 0xd0224
+/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
+#define CCM_REG_XX_OVFL_EVNT_ID 0xd0044
+/* [RW 18] Indirect access to the XX table of the XX protection mechanism.
+ The fields are: [5:0] - tail pointer; 11:6] - Link List size; 17:12] -
+ header pointer. */
+#define CCM_REG_XX_TABLE 0xd0280
+#define CDU_REG_CDU_CHK_MASK0 0x101000
+#define CDU_REG_CDU_CHK_MASK1 0x101004
+#define CDU_REG_CDU_CONTROL0 0x101008
+#define CDU_REG_CDU_DEBUG 0x101010
+#define CDU_REG_CDU_GLOBAL_PARAMS 0x101020
+/* [RW 7] Interrupt mask register #0 read/write */
+#define CDU_REG_CDU_INT_MASK 0x10103c
+/* [R 7] Interrupt register #0 read */
+#define CDU_REG_CDU_INT_STS 0x101030
+/* [RW 5] Parity mask register #0 read/write */
+#define CDU_REG_CDU_PRTY_MASK 0x10104c
+/* [R 5] Parity register #0 read */
+#define CDU_REG_CDU_PRTY_STS 0x101040
+/* [RC 5] Parity register #0 read clear */
+#define CDU_REG_CDU_PRTY_STS_CLR 0x101044
+/* [RC 32] logging of error data in case of a CDU load error:
+ {expected_cid[15:0]; xpected_type[2:0]; xpected_region[2:0]; ctive_error;
+ ype_error; ctual_active; ctual_compressed_context}; */
+#define CDU_REG_ERROR_DATA 0x101014
+/* [WB 216] L1TT ram access. each entry has the following format :
+ {mrege_regions[7:0]; ffset12[5:0]...offset0[5:0];
+ ength12[5:0]...length0[5:0]; d12[3:0]...id0[3:0]} */
+#define CDU_REG_L1TT 0x101800
+/* [WB 24] MATT ram access. each entry has the following
+ format:{RegionLength[11:0]; egionOffset[11:0]} */
+#define CDU_REG_MATT 0x101100
+/* [RW 1] when this bit is set the CDU operates in e1hmf mode */
+#define CDU_REG_MF_MODE 0x101050
+/* [R 1] indication the initializing the activity counter by the hardware
+ was done. */
+#define CFC_REG_AC_INIT_DONE 0x104078
+/* [RW 13] activity counter ram access */
+#define CFC_REG_ACTIVITY_COUNTER 0x104400
+#define CFC_REG_ACTIVITY_COUNTER_SIZE 256
+/* [R 1] indication the initializing the cams by the hardware was done. */
+#define CFC_REG_CAM_INIT_DONE 0x10407c
+/* [RW 2] Interrupt mask register #0 read/write */
+#define CFC_REG_CFC_INT_MASK 0x104108
+/* [R 2] Interrupt register #0 read */
+#define CFC_REG_CFC_INT_STS 0x1040fc
+/* [RC 2] Interrupt register #0 read clear */
+#define CFC_REG_CFC_INT_STS_CLR 0x104100
+/* [RW 4] Parity mask register #0 read/write */
+#define CFC_REG_CFC_PRTY_MASK 0x104118
+/* [R 4] Parity register #0 read */
+#define CFC_REG_CFC_PRTY_STS 0x10410c
+/* [RC 4] Parity register #0 read clear */
+#define CFC_REG_CFC_PRTY_STS_CLR 0x104110
+/* [RW 21] CID cam access (21:1 - Data; alid - 0) */
+#define CFC_REG_CID_CAM 0x104800
+#define CFC_REG_CONTROL0 0x104028
+#define CFC_REG_DEBUG0 0x104050
+/* [RW 14] indicates per error (in #cfc_registers_cfc_error_vector.cfc_error
+ vector) whether the cfc should be disabled upon it */
+#define CFC_REG_DISABLE_ON_ERROR 0x104044
+/* [RC 14] CFC error vector. when the CFC detects an internal error it will
+ set one of these bits. the bit description can be found in CFC
+ specifications */
+#define CFC_REG_ERROR_VECTOR 0x10403c
+/* [WB 93] LCID info ram access */
+#define CFC_REG_INFO_RAM 0x105000
+#define CFC_REG_INFO_RAM_SIZE 1024
+#define CFC_REG_INIT_REG 0x10404c
+#define CFC_REG_INTERFACES 0x104058
+/* [RW 24] {weight_load_client7[2:0] to weight_load_client0[2:0]}. this
+ field allows changing the priorities of the weighted-round-robin arbiter
+ which selects which CFC load client should be served next */
+#define CFC_REG_LCREQ_WEIGHTS 0x104084
+/* [RW 16] Link List ram access; data = {prev_lcid; ext_lcid} */
+#define CFC_REG_LINK_LIST 0x104c00
+#define CFC_REG_LINK_LIST_SIZE 256
+/* [R 1] indication the initializing the link list by the hardware was done. */
+#define CFC_REG_LL_INIT_DONE 0x104074
+/* [R 9] Number of allocated LCIDs which are at empty state */
+#define CFC_REG_NUM_LCIDS_ALLOC 0x104020
+/* [R 9] Number of Arriving LCIDs in Link List Block */
+#define CFC_REG_NUM_LCIDS_ARRIVING 0x104004
+#define CFC_REG_NUM_LCIDS_INSIDE_PF 0x104120
+/* [R 9] Number of Leaving LCIDs in Link List Block */
+#define CFC_REG_NUM_LCIDS_LEAVING 0x104018
+#define CFC_REG_WEAK_ENABLE_PF 0x104124
+/* [RW 8] The event id for aggregated interrupt 0 */
+#define CSDM_REG_AGG_INT_EVENT_0 0xc2038
+#define CSDM_REG_AGG_INT_EVENT_10 0xc2060
+#define CSDM_REG_AGG_INT_EVENT_11 0xc2064
+#define CSDM_REG_AGG_INT_EVENT_12 0xc2068
+#define CSDM_REG_AGG_INT_EVENT_13 0xc206c
+#define CSDM_REG_AGG_INT_EVENT_14 0xc2070
+#define CSDM_REG_AGG_INT_EVENT_15 0xc2074
+#define CSDM_REG_AGG_INT_EVENT_16 0xc2078
+#define CSDM_REG_AGG_INT_EVENT_2 0xc2040
+#define CSDM_REG_AGG_INT_EVENT_3 0xc2044
+#define CSDM_REG_AGG_INT_EVENT_4 0xc2048
+#define CSDM_REG_AGG_INT_EVENT_5 0xc204c
+#define CSDM_REG_AGG_INT_EVENT_6 0xc2050
+#define CSDM_REG_AGG_INT_EVENT_7 0xc2054
+#define CSDM_REG_AGG_INT_EVENT_8 0xc2058
+#define CSDM_REG_AGG_INT_EVENT_9 0xc205c
+/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
+ or auto-mask-mode (1) */
+#define CSDM_REG_AGG_INT_MODE_10 0xc21e0
+#define CSDM_REG_AGG_INT_MODE_11 0xc21e4
+#define CSDM_REG_AGG_INT_MODE_12 0xc21e8
+#define CSDM_REG_AGG_INT_MODE_13 0xc21ec
+#define CSDM_REG_AGG_INT_MODE_14 0xc21f0
+#define CSDM_REG_AGG_INT_MODE_15 0xc21f4
+#define CSDM_REG_AGG_INT_MODE_16 0xc21f8
+#define CSDM_REG_AGG_INT_MODE_6 0xc21d0
+#define CSDM_REG_AGG_INT_MODE_7 0xc21d4
+#define CSDM_REG_AGG_INT_MODE_8 0xc21d8
+#define CSDM_REG_AGG_INT_MODE_9 0xc21dc
+/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
+#define CSDM_REG_CFC_RSP_START_ADDR 0xc2008
+/* [RW 16] The maximum value of the completion counter #0 */
+#define CSDM_REG_CMP_COUNTER_MAX0 0xc201c
+/* [RW 16] The maximum value of the completion counter #1 */
+#define CSDM_REG_CMP_COUNTER_MAX1 0xc2020
+/* [RW 16] The maximum value of the completion counter #2 */
+#define CSDM_REG_CMP_COUNTER_MAX2 0xc2024
+/* [RW 16] The maximum value of the completion counter #3 */
+#define CSDM_REG_CMP_COUNTER_MAX3 0xc2028
+/* [RW 13] The start address in the internal RAM for the completion
+ counters. */
+#define CSDM_REG_CMP_COUNTER_START_ADDR 0xc200c
+/* [RW 32] Interrupt mask register #0 read/write */
+#define CSDM_REG_CSDM_INT_MASK_0 0xc229c
+#define CSDM_REG_CSDM_INT_MASK_1 0xc22ac
+/* [R 32] Interrupt register #0 read */
+#define CSDM_REG_CSDM_INT_STS_0 0xc2290
+#define CSDM_REG_CSDM_INT_STS_1 0xc22a0
+/* [RW 11] Parity mask register #0 read/write */
+#define CSDM_REG_CSDM_PRTY_MASK 0xc22bc
+/* [R 11] Parity register #0 read */
+#define CSDM_REG_CSDM_PRTY_STS 0xc22b0
+/* [RC 11] Parity register #0 read clear */
+#define CSDM_REG_CSDM_PRTY_STS_CLR 0xc22b4
+#define CSDM_REG_ENABLE_IN1 0xc2238
+#define CSDM_REG_ENABLE_IN2 0xc223c
+#define CSDM_REG_ENABLE_OUT1 0xc2240
+#define CSDM_REG_ENABLE_OUT2 0xc2244
+/* [RW 4] The initial number of messages that can be sent to the pxp control
+ interface without receiving any ACK. */
+#define CSDM_REG_INIT_CREDIT_PXP_CTRL 0xc24bc
+/* [ST 32] The number of ACK after placement messages received */
+#define CSDM_REG_NUM_OF_ACK_AFTER_PLACE 0xc227c
+/* [ST 32] The number of packet end messages received from the parser */
+#define CSDM_REG_NUM_OF_PKT_END_MSG 0xc2274
+/* [ST 32] The number of requests received from the pxp async if */
+#define CSDM_REG_NUM_OF_PXP_ASYNC_REQ 0xc2278
+/* [ST 32] The number of commands received in queue 0 */
+#define CSDM_REG_NUM_OF_Q0_CMD 0xc2248
+/* [ST 32] The number of commands received in queue 10 */
+#define CSDM_REG_NUM_OF_Q10_CMD 0xc226c
+/* [ST 32] The number of commands received in queue 11 */
+#define CSDM_REG_NUM_OF_Q11_CMD 0xc2270
+/* [ST 32] The number of commands received in queue 1 */
+#define CSDM_REG_NUM_OF_Q1_CMD 0xc224c
+/* [ST 32] The number of commands received in queue 3 */
+#define CSDM_REG_NUM_OF_Q3_CMD 0xc2250
+/* [ST 32] The number of commands received in queue 4 */
+#define CSDM_REG_NUM_OF_Q4_CMD 0xc2254
+/* [ST 32] The number of commands received in queue 5 */
+#define CSDM_REG_NUM_OF_Q5_CMD 0xc2258
+/* [ST 32] The number of commands received in queue 6 */
+#define CSDM_REG_NUM_OF_Q6_CMD 0xc225c
+/* [ST 32] The number of commands received in queue 7 */
+#define CSDM_REG_NUM_OF_Q7_CMD 0xc2260
+/* [ST 32] The number of commands received in queue 8 */
+#define CSDM_REG_NUM_OF_Q8_CMD 0xc2264
+/* [ST 32] The number of commands received in queue 9 */
+#define CSDM_REG_NUM_OF_Q9_CMD 0xc2268
+/* [RW 13] The start address in the internal RAM for queue counters */
+#define CSDM_REG_Q_COUNTER_START_ADDR 0xc2010
+/* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */
+#define CSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0xc2548
+/* [R 1] parser fifo empty in sdm_sync block */
+#define CSDM_REG_SYNC_PARSER_EMPTY 0xc2550
+/* [R 1] parser serial fifo empty in sdm_sync block */
+#define CSDM_REG_SYNC_SYNC_EMPTY 0xc2558
+/* [RW 32] Tick for timer counter. Applicable only when
+ ~csdm_registers_timer_tick_enable.timer_tick_enable =1 */
+#define CSDM_REG_TIMER_TICK 0xc2000
+/* [RW 5] The number of time_slots in the arbitration cycle */
+#define CSEM_REG_ARB_CYCLE_SIZE 0x200034
+/* [RW 3] The source that is associated with arbitration element 0. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2 */
+#define CSEM_REG_ARB_ELEMENT0 0x200020
+/* [RW 3] The source that is associated with arbitration element 1. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~csem_registers_arb_element0.arb_element0 */
+#define CSEM_REG_ARB_ELEMENT1 0x200024
+/* [RW 3] The source that is associated with arbitration element 2. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~csem_registers_arb_element0.arb_element0
+ and ~csem_registers_arb_element1.arb_element1 */
+#define CSEM_REG_ARB_ELEMENT2 0x200028
+/* [RW 3] The source that is associated with arbitration element 3. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.Could
+ not be equal to register ~csem_registers_arb_element0.arb_element0 and
+ ~csem_registers_arb_element1.arb_element1 and
+ ~csem_registers_arb_element2.arb_element2 */
+#define CSEM_REG_ARB_ELEMENT3 0x20002c
+/* [RW 3] The source that is associated with arbitration element 4. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~csem_registers_arb_element0.arb_element0
+ and ~csem_registers_arb_element1.arb_element1 and
+ ~csem_registers_arb_element2.arb_element2 and
+ ~csem_registers_arb_element3.arb_element3 */
+#define CSEM_REG_ARB_ELEMENT4 0x200030
+/* [RW 32] Interrupt mask register #0 read/write */
+#define CSEM_REG_CSEM_INT_MASK_0 0x200110
+#define CSEM_REG_CSEM_INT_MASK_1 0x200120
+/* [R 32] Interrupt register #0 read */
+#define CSEM_REG_CSEM_INT_STS_0 0x200104
+#define CSEM_REG_CSEM_INT_STS_1 0x200114
+/* [RW 32] Parity mask register #0 read/write */
+#define CSEM_REG_CSEM_PRTY_MASK_0 0x200130
+#define CSEM_REG_CSEM_PRTY_MASK_1 0x200140
+/* [R 32] Parity register #0 read */
+#define CSEM_REG_CSEM_PRTY_STS_0 0x200124
+#define CSEM_REG_CSEM_PRTY_STS_1 0x200134
+/* [RC 32] Parity register #0 read clear */
+#define CSEM_REG_CSEM_PRTY_STS_CLR_0 0x200128
+#define CSEM_REG_CSEM_PRTY_STS_CLR_1 0x200138
+#define CSEM_REG_ENABLE_IN 0x2000a4
+#define CSEM_REG_ENABLE_OUT 0x2000a8
+/* [RW 32] This address space contains all registers and memories that are
+ placed in SEM_FAST block. The SEM_FAST registers are described in
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
+#define CSEM_REG_FAST_MEMORY 0x220000
+/* [RW 1] Disables input messages from FIC0 May be updated during run_time
+ by the microcode */
+#define CSEM_REG_FIC0_DISABLE 0x200224
+/* [RW 1] Disables input messages from FIC1 May be updated during run_time
+ by the microcode */
+#define CSEM_REG_FIC1_DISABLE 0x200234
+/* [RW 15] Interrupt table Read and write access to it is not possible in
+ the middle of the work */
+#define CSEM_REG_INT_TABLE 0x200400
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC0 */
+#define CSEM_REG_MSG_NUM_FIC0 0x200000
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC1 */
+#define CSEM_REG_MSG_NUM_FIC1 0x200004
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC0 */
+#define CSEM_REG_MSG_NUM_FOC0 0x200008
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC1 */
+#define CSEM_REG_MSG_NUM_FOC1 0x20000c
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC2 */
+#define CSEM_REG_MSG_NUM_FOC2 0x200010
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC3 */
+#define CSEM_REG_MSG_NUM_FOC3 0x200014
+/* [RW 1] Disables input messages from the passive buffer May be updated
+ during run_time by the microcode */
+#define CSEM_REG_PAS_DISABLE 0x20024c
+/* [WB 128] Debug only. Passive buffer memory */
+#define CSEM_REG_PASSIVE_BUFFER 0x202000
+/* [WB 46] pram memory. B45 is parity; b[44:0] - data. */
+#define CSEM_REG_PRAM 0x240000
+/* [R 16] Valid sleeping threads indication have bit per thread */
+#define CSEM_REG_SLEEP_THREADS_VALID 0x20026c
+/* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */
+#define CSEM_REG_SLOW_EXT_STORE_EMPTY 0x2002a0
+/* [RW 16] List of free threads . There is a bit per thread. */
+#define CSEM_REG_THREADS_LIST 0x2002e4
+/* [RW 3] The arbitration scheme of time_slot 0 */
+#define CSEM_REG_TS_0_AS 0x200038
+/* [RW 3] The arbitration scheme of time_slot 10 */
+#define CSEM_REG_TS_10_AS 0x200060
+/* [RW 3] The arbitration scheme of time_slot 11 */
+#define CSEM_REG_TS_11_AS 0x200064
+/* [RW 3] The arbitration scheme of time_slot 12 */
+#define CSEM_REG_TS_12_AS 0x200068
+/* [RW 3] The arbitration scheme of time_slot 13 */
+#define CSEM_REG_TS_13_AS 0x20006c
+/* [RW 3] The arbitration scheme of time_slot 14 */
+#define CSEM_REG_TS_14_AS 0x200070
+/* [RW 3] The arbitration scheme of time_slot 15 */
+#define CSEM_REG_TS_15_AS 0x200074
+/* [RW 3] The arbitration scheme of time_slot 16 */
+#define CSEM_REG_TS_16_AS 0x200078
+/* [RW 3] The arbitration scheme of time_slot 17 */
+#define CSEM_REG_TS_17_AS 0x20007c
+/* [RW 3] The arbitration scheme of time_slot 18 */
+#define CSEM_REG_TS_18_AS 0x200080
+/* [RW 3] The arbitration scheme of time_slot 1 */
+#define CSEM_REG_TS_1_AS 0x20003c
+/* [RW 3] The arbitration scheme of time_slot 2 */
+#define CSEM_REG_TS_2_AS 0x200040
+/* [RW 3] The arbitration scheme of time_slot 3 */
+#define CSEM_REG_TS_3_AS 0x200044
+/* [RW 3] The arbitration scheme of time_slot 4 */
+#define CSEM_REG_TS_4_AS 0x200048
+/* [RW 3] The arbitration scheme of time_slot 5 */
+#define CSEM_REG_TS_5_AS 0x20004c
+/* [RW 3] The arbitration scheme of time_slot 6 */
+#define CSEM_REG_TS_6_AS 0x200050
+/* [RW 3] The arbitration scheme of time_slot 7 */
+#define CSEM_REG_TS_7_AS 0x200054
+/* [RW 3] The arbitration scheme of time_slot 8 */
+#define CSEM_REG_TS_8_AS 0x200058
+/* [RW 3] The arbitration scheme of time_slot 9 */
+#define CSEM_REG_TS_9_AS 0x20005c
+/* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64
+ * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */
+#define CSEM_REG_VFPF_ERR_NUM 0x200380
+/* [RW 1] Parity mask register #0 read/write */
+#define DBG_REG_DBG_PRTY_MASK 0xc0a8
+/* [R 1] Parity register #0 read */
+#define DBG_REG_DBG_PRTY_STS 0xc09c
+/* [RC 1] Parity register #0 read clear */
+#define DBG_REG_DBG_PRTY_STS_CLR 0xc0a0
+/* [RW 1] When set the DMAE will process the commands as in E1.5. 1.The
+ * function that is used is always SRC-PCI; 2.VF_Valid = 0; 3.VFID=0;
+ * 4.Completion function=0; 5.Error handling=0 */
+#define DMAE_REG_BACKWARD_COMP_EN 0x10207c
+/* [RW 32] Commands memory. The address to command X; row Y is to calculated
+ as 14*X+Y. */
+#define DMAE_REG_CMD_MEM 0x102400
+#define DMAE_REG_CMD_MEM_SIZE 224
+/* [RW 1] If 0 - the CRC-16c initial value is all zeroes; if 1 - the CRC-16c
+ initial value is all ones. */
+#define DMAE_REG_CRC16C_INIT 0x10201c
+/* [RW 1] If 0 - the CRC-16 T10 initial value is all zeroes; if 1 - the
+ CRC-16 T10 initial value is all ones. */
+#define DMAE_REG_CRC16T10_INIT 0x102020
+/* [RW 2] Interrupt mask register #0 read/write */
+#define DMAE_REG_DMAE_INT_MASK 0x102054
+/* [RW 4] Parity mask register #0 read/write */
+#define DMAE_REG_DMAE_PRTY_MASK 0x102064
+/* [R 4] Parity register #0 read */
+#define DMAE_REG_DMAE_PRTY_STS 0x102058
+/* [RC 4] Parity register #0 read clear */
+#define DMAE_REG_DMAE_PRTY_STS_CLR 0x10205c
+/* [RW 1] Command 0 go. */
+#define DMAE_REG_GO_C0 0x102080
+/* [RW 1] Command 1 go. */
+#define DMAE_REG_GO_C1 0x102084
+/* [RW 1] Command 10 go. */
+#define DMAE_REG_GO_C10 0x102088
+/* [RW 1] Command 11 go. */
+#define DMAE_REG_GO_C11 0x10208c
+/* [RW 1] Command 12 go. */
+#define DMAE_REG_GO_C12 0x102090
+/* [RW 1] Command 13 go. */
+#define DMAE_REG_GO_C13 0x102094
+/* [RW 1] Command 14 go. */
+#define DMAE_REG_GO_C14 0x102098
+/* [RW 1] Command 15 go. */
+#define DMAE_REG_GO_C15 0x10209c
+/* [RW 1] Command 2 go. */
+#define DMAE_REG_GO_C2 0x1020a0
+/* [RW 1] Command 3 go. */
+#define DMAE_REG_GO_C3 0x1020a4
+/* [RW 1] Command 4 go. */
+#define DMAE_REG_GO_C4 0x1020a8
+/* [RW 1] Command 5 go. */
+#define DMAE_REG_GO_C5 0x1020ac
+/* [RW 1] Command 6 go. */
+#define DMAE_REG_GO_C6 0x1020b0
+/* [RW 1] Command 7 go. */
+#define DMAE_REG_GO_C7 0x1020b4
+/* [RW 1] Command 8 go. */
+#define DMAE_REG_GO_C8 0x1020b8
+/* [RW 1] Command 9 go. */
+#define DMAE_REG_GO_C9 0x1020bc
+/* [RW 1] DMAE GRC Interface (Target; aster) enable. If 0 - the acknowledge
+ input is disregarded; valid is deasserted; all other signals are treated
+ as usual; if 1 - normal activity. */
+#define DMAE_REG_GRC_IFEN 0x102008
+/* [RW 1] DMAE PCI Interface (Request; ead; rite) enable. If 0 - the
+ acknowledge input is disregarded; valid is deasserted; full is asserted;
+ all other signals are treated as usual; if 1 - normal activity. */
+#define DMAE_REG_PCI_IFEN 0x102004
+/* [RW 4] DMAE- PCI Request Interface initial credit. Write writes the
+ initial value to the credit counter; related to the address. Read returns
+ the current value of the counter. */
+#define DMAE_REG_PXP_REQ_INIT_CRD 0x1020c0
+/* [RW 8] Aggregation command. */
+#define DORQ_REG_AGG_CMD0 0x170060
+/* [RW 8] Aggregation command. */
+#define DORQ_REG_AGG_CMD1 0x170064
+/* [RW 8] Aggregation command. */
+#define DORQ_REG_AGG_CMD2 0x170068
+/* [RW 8] Aggregation command. */
+#define DORQ_REG_AGG_CMD3 0x17006c
+/* [RW 28] UCM Header. */
+#define DORQ_REG_CMHEAD_RX 0x170050
+/* [RW 32] Doorbell address for RBC doorbells (function 0). */
+#define DORQ_REG_DB_ADDR0 0x17008c
+/* [RW 5] Interrupt mask register #0 read/write */
+#define DORQ_REG_DORQ_INT_MASK 0x170180
+/* [R 5] Interrupt register #0 read */
+#define DORQ_REG_DORQ_INT_STS 0x170174
+/* [RC 5] Interrupt register #0 read clear */
+#define DORQ_REG_DORQ_INT_STS_CLR 0x170178
+/* [RW 2] Parity mask register #0 read/write */
+#define DORQ_REG_DORQ_PRTY_MASK 0x170190
+/* [R 2] Parity register #0 read */
+#define DORQ_REG_DORQ_PRTY_STS 0x170184
+/* [RC 2] Parity register #0 read clear */
+#define DORQ_REG_DORQ_PRTY_STS_CLR 0x170188
+/* [RW 8] The address to write the DPM CID to STORM. */
+#define DORQ_REG_DPM_CID_ADDR 0x170044
+/* [RW 5] The DPM mode CID extraction offset. */
+#define DORQ_REG_DPM_CID_OFST 0x170030
+/* [RW 12] The threshold of the DQ FIFO to send the almost full interrupt. */
+#define DORQ_REG_DQ_FIFO_AFULL_TH 0x17007c
+/* [RW 12] The threshold of the DQ FIFO to send the full interrupt. */
+#define DORQ_REG_DQ_FIFO_FULL_TH 0x170078
+/* [R 13] Current value of the DQ FIFO fill level according to following
+ pointer. The range is 0 - 256 FIFO rows; where each row stands for the
+ doorbell. */
+#define DORQ_REG_DQ_FILL_LVLF 0x1700a4
+/* [R 1] DQ FIFO full status. Is set; when FIFO filling level is more or
+ equal to full threshold; reset on full clear. */
+#define DORQ_REG_DQ_FULL_ST 0x1700c0
+/* [RW 28] The value sent to CM header in the case of CFC load error. */
+#define DORQ_REG_ERR_CMHEAD 0x170058
+#define DORQ_REG_IF_EN 0x170004
+#define DORQ_REG_MAX_RVFID_SIZE 0x1701ec
+#define DORQ_REG_MODE_ACT 0x170008
+/* [RW 5] The normal mode CID extraction offset. */
+#define DORQ_REG_NORM_CID_OFST 0x17002c
+/* [RW 28] TCM Header when only TCP context is loaded. */
+#define DORQ_REG_NORM_CMHEAD_TX 0x17004c
+/* [RW 3] The number of simultaneous outstanding requests to Context Fetch
+ Interface. */
+#define DORQ_REG_OUTST_REQ 0x17003c
+#define DORQ_REG_PF_USAGE_CNT 0x1701d0
+#define DORQ_REG_REGN 0x170038
+/* [R 4] Current value of response A counter credit. Initial credit is
+ configured through write to ~dorq_registers_rsp_init_crd.rsp_init_crd
+ register. */
+#define DORQ_REG_RSPA_CRD_CNT 0x1700ac
+/* [R 4] Current value of response B counter credit. Initial credit is
+ configured through write to ~dorq_registers_rsp_init_crd.rsp_init_crd
+ register. */
+#define DORQ_REG_RSPB_CRD_CNT 0x1700b0
+/* [RW 4] The initial credit at the Doorbell Response Interface. The write
+ writes the same initial credit to the rspa_crd_cnt and rspb_crd_cnt. The
+ read reads this written value. */
+#define DORQ_REG_RSP_INIT_CRD 0x170048
+#define DORQ_REG_RSPB_CRD_CNT 0x1700b0
+#define DORQ_REG_VF_NORM_CID_BASE 0x1701a0
+#define DORQ_REG_VF_NORM_CID_OFST 0x1701f4
+#define DORQ_REG_VF_NORM_CID_WND_SIZE 0x1701a4
+#define DORQ_REG_VF_NORM_MAX_CID_COUNT 0x1701e4
+#define DORQ_REG_VF_NORM_VF_BASE 0x1701a8
+/* [RW 10] VF type validation mask value */
+#define DORQ_REG_VF_TYPE_MASK_0 0x170218
+/* [RW 17] VF type validation Min MCID value */
+#define DORQ_REG_VF_TYPE_MAX_MCID_0 0x1702d8
+/* [RW 17] VF type validation Max MCID value */
+#define DORQ_REG_VF_TYPE_MIN_MCID_0 0x170298
+/* [RW 10] VF type validation comp value */
+#define DORQ_REG_VF_TYPE_VALUE_0 0x170258
+#define DORQ_REG_VF_USAGE_CT_LIMIT 0x170340
+
+/* [RW 4] Initial activity counter value on the load request; when the
+ shortcut is done. */
+#define DORQ_REG_SHRT_ACT_CNT 0x170070
+/* [RW 28] TCM Header when both ULP and TCP context is loaded. */
+#define DORQ_REG_SHRT_CMHEAD 0x170054
+#define HC_CONFIG_0_REG_ATTN_BIT_EN_0 (0x1<<4)
+#define HC_CONFIG_0_REG_BLOCK_DISABLE_0 (0x1<<0)
+#define HC_CONFIG_0_REG_INT_LINE_EN_0 (0x1<<3)
+#define HC_CONFIG_0_REG_MSI_ATTN_EN_0 (0x1<<7)
+#define HC_CONFIG_0_REG_MSI_MSIX_INT_EN_0 (0x1<<2)
+#define HC_CONFIG_0_REG_SINGLE_ISR_EN_0 (0x1<<1)
+#define HC_CONFIG_1_REG_BLOCK_DISABLE_1 (0x1<<0)
+#define DORQ_REG_VF_USAGE_CNT 0x170320
+#define HC_REG_AGG_INT_0 0x108050
+#define HC_REG_AGG_INT_1 0x108054
+#define HC_REG_ATTN_BIT 0x108120
+#define HC_REG_ATTN_IDX 0x108100
+#define HC_REG_ATTN_MSG0_ADDR_L 0x108018
+#define HC_REG_ATTN_MSG1_ADDR_L 0x108020
+#define HC_REG_ATTN_NUM_P0 0x108038
+#define HC_REG_ATTN_NUM_P1 0x10803c
+#define HC_REG_COMMAND_REG 0x108180
+#define HC_REG_CONFIG_0 0x108000
+#define HC_REG_CONFIG_1 0x108004
+#define HC_REG_FUNC_NUM_P0 0x1080ac
+#define HC_REG_FUNC_NUM_P1 0x1080b0
+/* [RW 3] Parity mask register #0 read/write */
+#define HC_REG_HC_PRTY_MASK 0x1080a0
+/* [R 3] Parity register #0 read */
+#define HC_REG_HC_PRTY_STS 0x108094
+/* [RC 3] Parity register #0 read clear */
+#define HC_REG_HC_PRTY_STS_CLR 0x108098
+#define HC_REG_INT_MASK 0x108108
+#define HC_REG_LEADING_EDGE_0 0x108040
+#define HC_REG_LEADING_EDGE_1 0x108048
+#define HC_REG_MAIN_MEMORY 0x108800
+#define HC_REG_MAIN_MEMORY_SIZE 152
+#define HC_REG_P0_PROD_CONS 0x108200
+#define HC_REG_P1_PROD_CONS 0x108400
+#define HC_REG_PBA_COMMAND 0x108140
+#define HC_REG_PCI_CONFIG_0 0x108010
+#define HC_REG_PCI_CONFIG_1 0x108014
+#define HC_REG_STATISTIC_COUNTERS 0x109000
+#define HC_REG_TRAILING_EDGE_0 0x108044
+#define HC_REG_TRAILING_EDGE_1 0x10804c
+#define HC_REG_UC_RAM_ADDR_0 0x108028
+#define HC_REG_UC_RAM_ADDR_1 0x108030
+#define HC_REG_USTORM_ADDR_FOR_COALESCE 0x108068
+#define HC_REG_VQID_0 0x108008
+#define HC_REG_VQID_1 0x10800c
+#define IGU_BLOCK_CONFIGURATION_REG_BACKWARD_COMP_EN (0x1<<1)
+#define IGU_BLOCK_CONFIGURATION_REG_BLOCK_ENABLE (0x1<<0)
+#define IGU_REG_ATTENTION_ACK_BITS 0x130108
+/* [R 4] Debug: attn_fsm */
+#define IGU_REG_ATTN_FSM 0x130054
+#define IGU_REG_ATTN_MSG_ADDR_H 0x13011c
+#define IGU_REG_ATTN_MSG_ADDR_L 0x130120
+/* [R 4] Debug: [3] - attention write done message is pending (0-no pending;
+ * 1-pending). [2:0] = PFID. Pending means attention message was sent; but
+ * write done didn't receive. */
+#define IGU_REG_ATTN_WRITE_DONE_PENDING 0x130030
+#define IGU_REG_BLOCK_CONFIGURATION 0x130000
+#define IGU_REG_COMMAND_REG_32LSB_DATA 0x130124
+#define IGU_REG_COMMAND_REG_CTRL 0x13012c
+/* [WB_R 32] Cleanup bit status per SB. 1 = cleanup is set. 0 = cleanup bit
+ * is clear. The bits in this registers are set and clear via the producer
+ * command. Data valid only in addresses 0-4. all the rest are zero. */
+#define IGU_REG_CSTORM_TYPE_0_SB_CLEANUP 0x130200
+/* [R 5] Debug: ctrl_fsm */
+#define IGU_REG_CTRL_FSM 0x130064
+/* [R 1] data available for error memory. If this bit is clear do not red
+ * from error_handling_memory. */
+#define IGU_REG_ERROR_HANDLING_DATA_VALID 0x130130
+/* [RW 11] Parity mask register #0 read/write */
+#define IGU_REG_IGU_PRTY_MASK 0x1300a8
+/* [R 11] Parity register #0 read */
+#define IGU_REG_IGU_PRTY_STS 0x13009c
+/* [RC 11] Parity register #0 read clear */
+#define IGU_REG_IGU_PRTY_STS_CLR 0x1300a0
+/* [R 4] Debug: int_handle_fsm */
+#define IGU_REG_INT_HANDLE_FSM 0x130050
+#define IGU_REG_LEADING_EDGE_LATCH 0x130134
+/* [RW 14] mapping CAM; relevant for E2 operating mode only. [0] - valid.
+ * [6:1] - vector number; [13:7] - FID (if VF - [13] = 0; [12:7] = VF
+ * number; if PF - [13] = 1; [12:10] = 0; [9:7] = PF number); */
+#define IGU_REG_MAPPING_MEMORY 0x131000
+#define IGU_REG_MAPPING_MEMORY_SIZE 136
+#define IGU_REG_PBA_STATUS_LSB 0x130138
+#define IGU_REG_PBA_STATUS_MSB 0x13013c
+#define IGU_REG_PCI_PF_MSI_EN 0x130140
+#define IGU_REG_PCI_PF_MSIX_EN 0x130144
+#define IGU_REG_PCI_PF_MSIX_FUNC_MASK 0x130148
+/* [WB_R 32] Each bit represent the pending bits status for that SB. 0 = no
+ * pending; 1 = pending. Pendings means interrupt was asserted; and write
+ * done was not received. Data valid only in addresses 0-4. all the rest are
+ * zero. */
+#define IGU_REG_PENDING_BITS_STATUS 0x130300
+#define IGU_REG_PF_CONFIGURATION 0x130154
+/* [RW 20] producers only. E2 mode: address 0-135 match to the mapping
+ * memory; 136 - PF0 default prod; 137 PF1 default prod; 138 - PF2 default
+ * prod; 139 PF3 default prod; 140 - PF0 - ATTN prod; 141 - PF1 - ATTN prod;
+ * 142 - PF2 - ATTN prod; 143 - PF3 - ATTN prod; 144-147 reserved. E1.5 mode
+ * - In backward compatible mode; for non default SB; each even line in the
+ * memory holds the U producer and each odd line hold the C producer. The
+ * first 128 producer are for NDSB (PF0 - 0-31; PF1 - 32-63 and so on). The
+ * last 20 producers are for the DSB for each PF. each PF has five segments
+ * (the order inside each segment is PF0; PF1; PF2; PF3) - 128-131 U prods;
+ * 132-135 C prods; 136-139 X prods; 140-143 T prods; 144-147 ATTN prods; */
+#define IGU_REG_PROD_CONS_MEMORY 0x132000
+/* [R 3] Debug: pxp_arb_fsm */
+#define IGU_REG_PXP_ARB_FSM 0x130068
+/* [RW 6] Write one for each bit will reset the appropriate memory. When the
+ * memory reset finished the appropriate bit will be clear. Bit 0 - mapping
+ * memory; Bit 1 - SB memory; Bit 2 - SB interrupt and mask register; Bit 3
+ * - MSIX memory; Bit 4 - PBA memory; Bit 5 - statistics; */
+#define IGU_REG_RESET_MEMORIES 0x130158
+/* [R 4] Debug: sb_ctrl_fsm */
+#define IGU_REG_SB_CTRL_FSM 0x13004c
+#define IGU_REG_SB_INT_BEFORE_MASK_LSB 0x13015c
+#define IGU_REG_SB_INT_BEFORE_MASK_MSB 0x130160
+#define IGU_REG_SB_MASK_LSB 0x130164
+#define IGU_REG_SB_MASK_MSB 0x130168
+/* [RW 16] Number of command that were dropped without causing an interrupt
+ * due to: read access for WO BAR address; or write access for RO BAR
+ * address or any access for reserved address or PCI function error is set
+ * and address is not MSIX; PBA or cleanup */
+#define IGU_REG_SILENT_DROP 0x13016c
+/* [RW 10] Number of MSI/MSIX/ATTN messages sent for the function: 0-63 -
+ * number of MSIX messages per VF; 64-67 - number of MSI/MSIX messages per
+ * PF; 68-71 number of ATTN messages per PF */
+#define IGU_REG_STATISTIC_NUM_MESSAGE_SENT 0x130800
+/* [RW 32] Number of cycles the timer mask masking the IGU interrupt when a
+ * timer mask command arrives. Value must be bigger than 100. */
+#define IGU_REG_TIMER_MASKING_VALUE 0x13003c
+#define IGU_REG_TRAILING_EDGE_LATCH 0x130104
+#define IGU_REG_VF_CONFIGURATION 0x130170
+/* [WB_R 32] Each bit represent write done pending bits status for that SB
+ * (MSI/MSIX message was sent and write done was not received yet). 0 =
+ * clear; 1 = set. Data valid only in addresses 0-4. all the rest are zero. */
+#define IGU_REG_WRITE_DONE_PENDING 0x130480
+#define MCP_A_REG_MCPR_SCRATCH 0x3a0000
+#define MCP_REG_MCPR_ACCESS_LOCK 0x8009c
+#define MCP_REG_MCPR_CPU_PROGRAM_COUNTER 0x8501c
+#define MCP_REG_MCPR_GP_INPUTS 0x800c0
+#define MCP_REG_MCPR_GP_OENABLE 0x800c8
+#define MCP_REG_MCPR_GP_OUTPUTS 0x800c4
+#define MCP_REG_MCPR_IMC_COMMAND 0x85900
+#define MCP_REG_MCPR_IMC_DATAREG0 0x85920
+#define MCP_REG_MCPR_IMC_SLAVE_CONTROL 0x85904
+#define MCP_REG_MCPR_CPU_PROGRAM_COUNTER 0x8501c
+#define MCP_REG_MCPR_NVM_ACCESS_ENABLE 0x86424
+#define MCP_REG_MCPR_NVM_ADDR 0x8640c
+#define MCP_REG_MCPR_NVM_CFG4 0x8642c
+#define MCP_REG_MCPR_NVM_COMMAND 0x86400
+#define MCP_REG_MCPR_NVM_READ 0x86410
+#define MCP_REG_MCPR_NVM_SW_ARB 0x86420
+#define MCP_REG_MCPR_NVM_WRITE 0x86408
+#define MCP_REG_MCPR_SCRATCH 0xa0000
+#define MISC_AEU_GENERAL_MASK_REG_AEU_NIG_CLOSE_MASK (0x1<<1)
+#define MISC_AEU_GENERAL_MASK_REG_AEU_PXP_CLOSE_MASK (0x1<<0)
+/* [R 32] read first 32 bit after inversion of function 0. mapped as
+ follows: [0] NIG attention for function0; [1] NIG attention for
+ function1; [2] GPIO1 mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp;
+ [6] GPIO1 function 1; [7] GPIO2 function 1; [8] GPIO3 function 1; [9]
+ GPIO4 function 1; [10] PCIE glue/PXP VPD event function0; [11] PCIE
+ glue/PXP VPD event function1; [12] PCIE glue/PXP Expansion ROM event0;
+ [13] PCIE glue/PXP Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16]
+ MSI/X indication for mcp; [17] MSI/X indication for function 1; [18] BRB
+ Parity error; [19] BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw
+ interrupt; [22] SRC Parity error; [23] SRC Hw interrupt; [24] TSDM Parity
+ error; [25] TSDM Hw interrupt; [26] TCM Parity error; [27] TCM Hw
+ interrupt; [28] TSEMI Parity error; [29] TSEMI Hw interrupt; [30] PBF
+ Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 0xa42c
+#define MISC_REG_AEU_AFTER_INVERT_1_FUNC_1 0xa430
+/* [R 32] read first 32 bit after inversion of mcp. mapped as follows: [0]
+ NIG attention for function0; [1] NIG attention for function1; [2] GPIO1
+ mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1;
+ [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10]
+ PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event
+ function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP
+ Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for
+ mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19]
+ BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC
+ Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw
+ interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI
+ Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw
+ interrupt; */
+#define MISC_REG_AEU_AFTER_INVERT_1_MCP 0xa434
+/* [R 32] read second 32 bit after inversion of function 0. mapped as
+ follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
+#define MISC_REG_AEU_AFTER_INVERT_2_FUNC_0 0xa438
+#define MISC_REG_AEU_AFTER_INVERT_2_FUNC_1 0xa43c
+/* [R 32] read second 32 bit after inversion of mcp. mapped as follows: [0]
+ PBClient Parity error; [1] PBClient Hw interrupt; [2] QM Parity error;
+ [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw interrupt;
+ [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity error; [9]
+ XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw interrupt; [12]
+ DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] NIG Parity
+ error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; [17] Vaux
+ PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw interrupt;
+ [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM Parity error;
+ [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI Hw interrupt;
+ [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM Parity error;
+ [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw interrupt; */
+#define MISC_REG_AEU_AFTER_INVERT_2_MCP 0xa440
+/* [R 32] read third 32 bit after inversion of function 0. mapped as
+ follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP Parity
+ error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error; [5]
+ PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
+#define MISC_REG_AEU_AFTER_INVERT_3_FUNC_0 0xa444
+#define MISC_REG_AEU_AFTER_INVERT_3_FUNC_1 0xa448
+/* [R 32] read third 32 bit after inversion of mcp. mapped as follows: [0]
+ CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP Parity error; [3] PXP
+ Hw interrupt; [4] PXPpciClockClient Parity error; [5] PXPpciClockClient
+ Hw interrupt; [6] CFC Parity error; [7] CFC Hw interrupt; [8] CDU Parity
+ error; [9] CDU Hw interrupt; [10] DMAE Parity error; [11] DMAE Hw
+ interrupt; [12] IGU (HC) Parity error; [13] IGU (HC) Hw interrupt; [14]
+ MISC Parity error; [15] MISC Hw interrupt; [16] pxp_misc_mps_attn; [17]
+ Flash event; [18] SMB event; [19] MCP attn0; [20] MCP attn1; [21] SW
+ timers attn_1 func0; [22] SW timers attn_2 func0; [23] SW timers attn_3
+ func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW timers attn_1
+ func1; [27] SW timers attn_2 func1; [28] SW timers attn_3 func1; [29] SW
+ timers attn_4 func1; [30] General attn0; [31] General attn1; */
+#define MISC_REG_AEU_AFTER_INVERT_3_MCP 0xa44c
+/* [R 32] read fourth 32 bit after inversion of function 0. mapped as
+ follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_AFTER_INVERT_4_FUNC_0 0xa450
+#define MISC_REG_AEU_AFTER_INVERT_4_FUNC_1 0xa454
+/* [R 32] read fourth 32 bit after inversion of mcp. mapped as follows: [0]
+ General attn2; [1] General attn3; [2] General attn4; [3] General attn5;
+ [4] General attn6; [5] General attn7; [6] General attn8; [7] General
+ attn9; [8] General attn10; [9] General attn11; [10] General attn12; [11]
+ General attn13; [12] General attn14; [13] General attn15; [14] General
+ attn16; [15] General attn17; [16] General attn18; [17] General attn19;
+ [18] General attn20; [19] General attn21; [20] Main power interrupt; [21]
+ RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN Latched attn; [24]
+ RBCU Latched attn; [25] RBCP Latched attn; [26] GRC Latched timeout
+ attention; [27] GRC Latched reserved access attention; [28] MCP Latched
+ rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP Latched
+ ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_AFTER_INVERT_4_MCP 0xa458
+/* [R 32] Read fifth 32 bit after inversion of function 0. Mapped as
+ * follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC
+ * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6]
+ * CNIG attention (reserved); [7] CNIG parity (reserved); [31-8] Reserved; */
+#define MISC_REG_AEU_AFTER_INVERT_5_FUNC_0 0xa700
+/* [W 14] write to this register results with the clear of the latched
+ signals; one in d0 clears RBCR latch; one in d1 clears RBCT latch; one in
+ d2 clears RBCN latch; one in d3 clears RBCU latch; one in d4 clears RBCP
+ latch; one in d5 clears GRC Latched timeout attention; one in d6 clears
+ GRC Latched reserved access attention; one in d7 clears Latched
+ rom_parity; one in d8 clears Latched ump_rx_parity; one in d9 clears
+ Latched ump_tx_parity; one in d10 clears Latched scpad_parity (both
+ ports); one in d11 clears pxpv_misc_mps_attn; one in d12 clears
+ pxp_misc_exp_rom_attn0; one in d13 clears pxp_misc_exp_rom_attn1; read
+ from this register return zero */
+#define MISC_REG_AEU_CLR_LATCH_SIGNAL 0xa45c
+/* [RW 32] first 32b for enabling the output for function 0 output0. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
+ function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
+ 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
+ GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
+ function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP
+ Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14]
+ SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X
+ indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt;
+ [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23]
+ SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26]
+ TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29]
+ TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0 0xa06c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_1 0xa07c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_2 0xa08c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_3 0xa09c
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_5 0xa0bc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_6 0xa0cc
+#define MISC_REG_AEU_ENABLE1_FUNC_0_OUT_7 0xa0dc
+/* [RW 32] first 32b for enabling the output for function 1 output0. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
+ function1; [2] GPIO1 function 1; [3] GPIO2 function 1; [4] GPIO3 function
+ 1; [5] GPIO4 function 1; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
+ GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
+ function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP
+ Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14]
+ SPIO4; [15] SPIO5; [16] MSI/X indication for function 1; [17] MSI/X
+ indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt;
+ [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23]
+ SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26]
+ TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29]
+ TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 0xa10c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_1 0xa11c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_2 0xa12c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_3 0xa13c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_5 0xa15c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_6 0xa16c
+#define MISC_REG_AEU_ENABLE1_FUNC_1_OUT_7 0xa17c
+/* [RW 32] first 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
+ function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
+ 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
+ GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
+ function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP
+ Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14]
+ SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X
+ indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt;
+ [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23]
+ SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26]
+ TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29]
+ TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_ENABLE1_NIG_0 0xa0ec
+#define MISC_REG_AEU_ENABLE1_NIG_1 0xa18c
+/* [RW 32] first 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] NIG attention for function0; [1] NIG attention for
+ function1; [2] GPIO1 function 0; [3] GPIO2 function 0; [4] GPIO3 function
+ 0; [5] GPIO4 function 0; [6] GPIO1 function 1; [7] GPIO2 function 1; [8]
+ GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
+ function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP
+ Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14]
+ SPIO4; [15] SPIO5; [16] MSI/X indication for function 0; [17] MSI/X
+ indication for function 1; [18] BRB Parity error; [19] BRB Hw interrupt;
+ [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23]
+ SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26]
+ TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29]
+ TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_ENABLE1_PXP_0 0xa0fc
+#define MISC_REG_AEU_ENABLE1_PXP_1 0xa19c
+/* [RW 32] second 32b for enabling the output for function 0 output0. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
+#define MISC_REG_AEU_ENABLE2_FUNC_0_OUT_0 0xa070
+#define MISC_REG_AEU_ENABLE2_FUNC_0_OUT_1 0xa080
+/* [RW 32] second 32b for enabling the output for function 1 output0. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
+#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_0 0xa110
+#define MISC_REG_AEU_ENABLE2_FUNC_1_OUT_1 0xa120
+/* [RW 32] second 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
+#define MISC_REG_AEU_ENABLE2_NIG_0 0xa0f0
+#define MISC_REG_AEU_ENABLE2_NIG_1 0xa190
+/* [RW 32] second 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] PBClient Parity error; [1] PBClient Hw interrupt; [2] QM
+ Parity error; [3] QM Hw interrupt; [4] Timers Parity error; [5] Timers Hw
+ interrupt; [6] XSDM Parity error; [7] XSDM Hw interrupt; [8] XCM Parity
+ error; [9] XCM Hw interrupt; [10] XSEMI Parity error; [11] XSEMI Hw
+ interrupt; [12] DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14]
+ NIG Parity error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error;
+ [17] Vaux PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw
+ interrupt; [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM
+ Parity error; [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI
+ Hw interrupt; [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM
+ Parity error; [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw
+ interrupt; */
+#define MISC_REG_AEU_ENABLE2_PXP_0 0xa100
+#define MISC_REG_AEU_ENABLE2_PXP_1 0xa1a0
+/* [RW 32] third 32b for enabling the output for function 0 output0. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
+#define MISC_REG_AEU_ENABLE3_FUNC_0_OUT_0 0xa074
+#define MISC_REG_AEU_ENABLE3_FUNC_0_OUT_1 0xa084
+/* [RW 32] third 32b for enabling the output for function 1 output0. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
+#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_0 0xa114
+#define MISC_REG_AEU_ENABLE3_FUNC_1_OUT_1 0xa124
+/* [RW 32] third 32b for enabling the output for close the gate nig. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
+#define MISC_REG_AEU_ENABLE3_NIG_0 0xa0f4
+#define MISC_REG_AEU_ENABLE3_NIG_1 0xa194
+/* [RW 32] third 32b for enabling the output for close the gate pxp. mapped
+ as follows: [0] CSEMI Parity error; [1] CSEMI Hw interrupt; [2] PXP
+ Parity error; [3] PXP Hw interrupt; [4] PXPpciClockClient Parity error;
+ [5] PXPpciClockClient Hw interrupt; [6] CFC Parity error; [7] CFC Hw
+ interrupt; [8] CDU Parity error; [9] CDU Hw interrupt; [10] DMAE Parity
+ error; [11] DMAE Hw interrupt; [12] IGU (HC) Parity error; [13] IGU (HC)
+ Hw interrupt; [14] MISC Parity error; [15] MISC Hw interrupt; [16]
+ pxp_misc_mps_attn; [17] Flash event; [18] SMB event; [19] MCP attn0; [20]
+ MCP attn1; [21] SW timers attn_1 func0; [22] SW timers attn_2 func0; [23]
+ SW timers attn_3 func0; [24] SW timers attn_4 func0; [25] PERST; [26] SW
+ timers attn_1 func1; [27] SW timers attn_2 func1; [28] SW timers attn_3
+ func1; [29] SW timers attn_4 func1; [30] General attn0; [31] General
+ attn1; */
+#define MISC_REG_AEU_ENABLE3_PXP_0 0xa104
+#define MISC_REG_AEU_ENABLE3_PXP_1 0xa1a4
+/* [RW 32] fourth 32b for enabling the output for function 0 output0.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_0 0xa078
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_2 0xa098
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_4 0xa0b8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_5 0xa0c8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_6 0xa0d8
+#define MISC_REG_AEU_ENABLE4_FUNC_0_OUT_7 0xa0e8
+/* [RW 32] fourth 32b for enabling the output for function 1 output0.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_0 0xa118
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_2 0xa138
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_4 0xa158
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_5 0xa168
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_6 0xa178
+#define MISC_REG_AEU_ENABLE4_FUNC_1_OUT_7 0xa188
+/* [RW 32] fourth 32b for enabling the output for close the gate nig.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_NIG_0 0xa0f8
+#define MISC_REG_AEU_ENABLE4_NIG_1 0xa198
+/* [RW 32] fourth 32b for enabling the output for close the gate pxp.mapped
+ as follows: [0] General attn2; [1] General attn3; [2] General attn4; [3]
+ General attn5; [4] General attn6; [5] General attn7; [6] General attn8;
+ [7] General attn9; [8] General attn10; [9] General attn11; [10] General
+ attn12; [11] General attn13; [12] General attn14; [13] General attn15;
+ [14] General attn16; [15] General attn17; [16] General attn18; [17]
+ General attn19; [18] General attn20; [19] General attn21; [20] Main power
+ interrupt; [21] RBCR Latched attn; [22] RBCT Latched attn; [23] RBCN
+ Latched attn; [24] RBCU Latched attn; [25] RBCP Latched attn; [26] GRC
+ Latched timeout attention; [27] GRC Latched reserved access attention;
+ [28] MCP Latched rom_parity; [29] MCP Latched ump_rx_parity; [30] MCP
+ Latched ump_tx_parity; [31] MCP Latched scpad_parity; */
+#define MISC_REG_AEU_ENABLE4_PXP_0 0xa108
+#define MISC_REG_AEU_ENABLE4_PXP_1 0xa1a8
+/* [RW 32] fifth 32b for enabling the output for function 0 output0. Mapped
+ * as follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC
+ * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6]
+ * mstat0 attention; [7] mstat0 parity; [8] mstat1 attention; [9] mstat1
+ * parity; [31-10] Reserved; */
+#define MISC_REG_AEU_ENABLE5_FUNC_0_OUT_0 0xa688
+/* [RW 32] Fifth 32b for enabling the output for function 1 output0. Mapped
+ * as follows: [0] PGLUE config_space; [1] PGLUE misc_flr; [2] PGLUE B RBC
+ * attention [3] PGLUE B RBC parity; [4] ATC attention; [5] ATC parity; [6]
+ * mstat0 attention; [7] mstat0 parity; [8] mstat1 attention; [9] mstat1
+ * parity; [31-10] Reserved; */
+#define MISC_REG_AEU_ENABLE5_FUNC_1_OUT_0 0xa6b0
+/* [RW 1] set/clr general attention 0; this will set/clr bit 94 in the aeu
+ 128 bit vector */
+#define MISC_REG_AEU_GENERAL_ATTN_0 0xa000
+#define MISC_REG_AEU_GENERAL_ATTN_1 0xa004
+#define MISC_REG_AEU_GENERAL_ATTN_10 0xa028
+#define MISC_REG_AEU_GENERAL_ATTN_11 0xa02c
+#define MISC_REG_AEU_GENERAL_ATTN_12 0xa030
+#define MISC_REG_AEU_GENERAL_ATTN_2 0xa008
+#define MISC_REG_AEU_GENERAL_ATTN_3 0xa00c
+#define MISC_REG_AEU_GENERAL_ATTN_4 0xa010
+#define MISC_REG_AEU_GENERAL_ATTN_5 0xa014
+#define MISC_REG_AEU_GENERAL_ATTN_6 0xa018
+#define MISC_REG_AEU_GENERAL_ATTN_7 0xa01c
+#define MISC_REG_AEU_GENERAL_ATTN_8 0xa020
+#define MISC_REG_AEU_GENERAL_ATTN_9 0xa024
+#define MISC_REG_AEU_GENERAL_MASK 0xa61c
+/* [RW 32] first 32b for inverting the input for function 0; for each bit:
+ 0= do not invert; 1= invert; mapped as follows: [0] NIG attention for
+ function0; [1] NIG attention for function1; [2] GPIO1 mcp; [3] GPIO2 mcp;
+ [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1; [7] GPIO2 function 1;
+ [8] GPIO3 function 1; [9] GPIO4 function 1; [10] PCIE glue/PXP VPD event
+ function0; [11] PCIE glue/PXP VPD event function1; [12] PCIE glue/PXP
+ Expansion ROM event0; [13] PCIE glue/PXP Expansion ROM event1; [14]
+ SPIO4; [15] SPIO5; [16] MSI/X indication for mcp; [17] MSI/X indication
+ for function 1; [18] BRB Parity error; [19] BRB Hw interrupt; [20] PRS
+ Parity error; [21] PRS Hw interrupt; [22] SRC Parity error; [23] SRC Hw
+ interrupt; [24] TSDM Parity error; [25] TSDM Hw interrupt; [26] TCM
+ Parity error; [27] TCM Hw interrupt; [28] TSEMI Parity error; [29] TSEMI
+ Hw interrupt; [30] PBF Parity error; [31] PBF Hw interrupt; */
+#define MISC_REG_AEU_INVERTER_1_FUNC_0 0xa22c
+#define MISC_REG_AEU_INVERTER_1_FUNC_1 0xa23c
+/* [RW 32] second 32b for inverting the input for function 0; for each bit:
+ 0= do not invert; 1= invert. mapped as follows: [0] PBClient Parity
+ error; [1] PBClient Hw interrupt; [2] QM Parity error; [3] QM Hw
+ interrupt; [4] Timers Parity error; [5] Timers Hw interrupt; [6] XSDM
+ Parity error; [7] XSDM Hw interrupt; [8] XCM Parity error; [9] XCM Hw
+ interrupt; [10] XSEMI Parity error; [11] XSEMI Hw interrupt; [12]
+ DoorbellQ Parity error; [13] DoorbellQ Hw interrupt; [14] NIG Parity
+ error; [15] NIG Hw interrupt; [16] Vaux PCI core Parity error; [17] Vaux
+ PCI core Hw interrupt; [18] Debug Parity error; [19] Debug Hw interrupt;
+ [20] USDM Parity error; [21] USDM Hw interrupt; [22] UCM Parity error;
+ [23] UCM Hw interrupt; [24] USEMI Parity error; [25] USEMI Hw interrupt;
+ [26] UPB Parity error; [27] UPB Hw interrupt; [28] CSDM Parity error;
+ [29] CSDM Hw interrupt; [30] CCM Parity error; [31] CCM Hw interrupt; */
+#define MISC_REG_AEU_INVERTER_2_FUNC_0 0xa230
+#define MISC_REG_AEU_INVERTER_2_FUNC_1 0xa240
+/* [RW 10] [7:0] = mask 8 attention output signals toward IGU function0;
+ [9:8] = raserved. Zero = mask; one = unmask */
+#define MISC_REG_AEU_MASK_ATTN_FUNC_0 0xa060
+#define MISC_REG_AEU_MASK_ATTN_FUNC_1 0xa064
+/* [RW 1] If set a system kill occurred */
+#define MISC_REG_AEU_SYS_KILL_OCCURRED 0xa610
+/* [RW 32] Represent the status of the input vector to the AEU when a system
+ kill occurred. The register is reset in por reset. Mapped as follows: [0]
+ NIG attention for function0; [1] NIG attention for function1; [2] GPIO1
+ mcp; [3] GPIO2 mcp; [4] GPIO3 mcp; [5] GPIO4 mcp; [6] GPIO1 function 1;
+ [7] GPIO2 function 1; [8] GPIO3 function 1; [9] GPIO4 function 1; [10]
+ PCIE glue/PXP VPD event function0; [11] PCIE glue/PXP VPD event
+ function1; [12] PCIE glue/PXP Expansion ROM event0; [13] PCIE glue/PXP
+ Expansion ROM event1; [14] SPIO4; [15] SPIO5; [16] MSI/X indication for
+ mcp; [17] MSI/X indication for function 1; [18] BRB Parity error; [19]
+ BRB Hw interrupt; [20] PRS Parity error; [21] PRS Hw interrupt; [22] SRC
+ Parity error; [23] SRC Hw interrupt; [24] TSDM Parity error; [25] TSDM Hw
+ interrupt; [26] TCM Parity error; [27] TCM Hw interrupt; [28] TSEMI
+ Parity error; [29] TSEMI Hw interrupt; [30] PBF Parity error; [31] PBF Hw
+ interrupt; */
+#define MISC_REG_AEU_SYS_KILL_STATUS_0 0xa600
+#define MISC_REG_AEU_SYS_KILL_STATUS_1 0xa604
+#define MISC_REG_AEU_SYS_KILL_STATUS_2 0xa608
+#define MISC_REG_AEU_SYS_KILL_STATUS_3 0xa60c
+/* [R 4] This field indicates the type of the device. '0' - 2 Ports; '1' - 1
+ Port. */
+#define MISC_REG_BOND_ID 0xa400
+/* [R 16] These bits indicate the part number for the chip. */
+#define MISC_REG_CHIP_NUM 0xa408
+/* [R 4] These bits indicate the base revision of the chip. This value
+ starts at 0x0 for the A0 tape-out and increments by one for each
+ all-layer tape-out. */
+#define MISC_REG_CHIP_REV 0xa40c
+/* [R 14] otp_misc_do[100:0] spare bits collection: 13:11-
+ * otp_misc_do[100:98]; 10:7 - otp_misc_do[87:84]; 6:3 - otp_misc_do[75:72];
+ * 2:1 - otp_misc_do[51:50]; 0 - otp_misc_do[1]. */
+#define MISC_REG_CHIP_TYPE 0xac60
+#define MISC_REG_CHIP_TYPE_57811_MASK (1<<1)
+#define MISC_REG_CPMU_LP_DR_ENABLE 0xa858
+/* [RW 1] FW EEE LPI Enable. When 1 indicates that EEE LPI mode is enabled
+ * by FW. When 0 indicates that the EEE LPI mode is disabled by FW. Clk
+ * 25MHz. Reset on hard reset. */
+#define MISC_REG_CPMU_LP_FW_ENABLE_P0 0xa84c
+/* [RW 32] EEE LPI Idle Threshold. The threshold value for the idle EEE LPI
+ * counter. Timer tick is 1 us. Clock 25MHz. Reset on hard reset. */
+#define MISC_REG_CPMU_LP_IDLE_THR_P0 0xa8a0
+/* [RW 18] LPI entry events mask. [0] - Vmain SM Mask. When 1 indicates that
+ * the Vmain SM end state is disabled. When 0 indicates that the Vmain SM
+ * end state is enabled. [1] - FW Queues Empty Mask. When 1 indicates that
+ * the FW command that all Queues are empty is disabled. When 0 indicates
+ * that the FW command that all Queues are empty is enabled. [2] - FW Early
+ * Exit Mask / Reserved (Entry mask). When 1 indicates that the FW Early
+ * Exit command is disabled. When 0 indicates that the FW Early Exit command
+ * is enabled. This bit applicable only in the EXIT Events Mask registers.
+ * [3] - PBF Request Mask. When 1 indicates that the PBF Request indication
+ * is disabled. When 0 indicates that the PBF Request indication is enabled.
+ * [4] - Tx Request Mask. When =1 indicates that the Tx other Than PBF
+ * Request indication is disabled. When 0 indicates that the Tx Other Than
+ * PBF Request indication is enabled. [5] - Rx EEE LPI Status Mask. When 1
+ * indicates that the RX EEE LPI Status indication is disabled. When 0
+ * indicates that the RX EEE LPI Status indication is enabled. In the EXIT
+ * Events Masks registers; this bit masks the falling edge detect of the LPI
+ * Status (Rx LPI is on - off). [6] - Tx Pause Mask. When 1 indicates that
+ * the Tx Pause indication is disabled. When 0 indicates that the Tx Pause
+ * indication is enabled. [7] - BRB1 Empty Mask. When 1 indicates that the
+ * BRB1 EMPTY indication is disabled. When 0 indicates that the BRB1 EMPTY
+ * indication is enabled. [8] - QM Idle Mask. When 1 indicates that the QM
+ * IDLE indication is disabled. When 0 indicates that the QM IDLE indication
+ * is enabled. (One bit for both VOQ0 and VOQ1). [9] - QM LB Idle Mask. When
+ * 1 indicates that the QM IDLE indication for LOOPBACK is disabled. When 0
+ * indicates that the QM IDLE indication for LOOPBACK is enabled. [10] - L1
+ * Status Mask. When 1 indicates that the L1 Status indication from the PCIE
+ * CORE is disabled. When 0 indicates that the RX EEE LPI Status indication
+ * from the PCIE CORE is enabled. In the EXIT Events Masks registers; this
+ * bit masks the falling edge detect of the L1 status (L1 is on - off). [11]
+ * - P0 E0 EEE EEE LPI REQ Mask. When =1 indicates that the P0 E0 EEE EEE
+ * LPI REQ indication is disabled. When =0 indicates that the P0 E0 EEE LPI
+ * REQ indication is enabled. [12] - P1 E0 EEE LPI REQ Mask. When =1
+ * indicates that the P0 EEE LPI REQ indication is disabled. When =0
+ * indicates that the P0 EEE LPI REQ indication is enabled. [13] - P0 E1 EEE
+ * LPI REQ Mask. When =1 indicates that the P0 EEE LPI REQ indication is
+ * disabled. When =0 indicates that the P0 EEE LPI REQ indication is
+ * enabled. [14] - P1 E1 EEE LPI REQ Mask. When =1 indicates that the P0 EEE
+ * LPI REQ indication is disabled. When =0 indicates that the P0 EEE LPI REQ
+ * indication is enabled. [15] - L1 REQ Mask. When =1 indicates that the L1
+ * REQ indication is disabled. When =0 indicates that the L1 indication is
+ * enabled. [16] - Rx EEE LPI Status Edge Detect Mask. When =1 indicates
+ * that the RX EEE LPI Status Falling Edge Detect indication is disabled (Rx
+ * EEE LPI is on - off). When =0 indicates that the RX EEE LPI Status
+ * Falling Edge Detec indication is enabled (Rx EEE LPI is on - off). This
+ * bit is applicable only in the EXIT Events Masks registers. [17] - L1
+ * Status Edge Detect Mask. When =1 indicates that the L1 Status Falling
+ * Edge Detect indication from the PCIE CORE is disabled (L1 is on - off).
+ * When =0 indicates that the L1 Status Falling Edge Detect indication from
+ * the PCIE CORE is enabled (L1 is on - off). This bit is applicable only in
+ * the EXIT Events Masks registers. Clock 25MHz. Reset on hard reset. */
+#define MISC_REG_CPMU_LP_MASK_ENT_P0 0xa880
+/* [RW 18] EEE LPI exit events mask. [0] - Vmain SM Mask. When 1 indicates
+ * that the Vmain SM end state is disabled. When 0 indicates that the Vmain
+ * SM end state is enabled. [1] - FW Queues Empty Mask. When 1 indicates
+ * that the FW command that all Queues are empty is disabled. When 0
+ * indicates that the FW command that all Queues are empty is enabled. [2] -
+ * FW Early Exit Mask / Reserved (Entry mask). When 1 indicates that the FW
+ * Early Exit command is disabled. When 0 indicates that the FW Early Exit
+ * command is enabled. This bit applicable only in the EXIT Events Mask
+ * registers. [3] - PBF Request Mask. When 1 indicates that the PBF Request
+ * indication is disabled. When 0 indicates that the PBF Request indication
+ * is enabled. [4] - Tx Request Mask. When =1 indicates that the Tx other
+ * Than PBF Request indication is disabled. When 0 indicates that the Tx
+ * Other Than PBF Request indication is enabled. [5] - Rx EEE LPI Status
+ * Mask. When 1 indicates that the RX EEE LPI Status indication is disabled.
+ * When 0 indicates that the RX LPI Status indication is enabled. In the
+ * EXIT Events Masks registers; this bit masks the falling edge detect of
+ * the EEE LPI Status (Rx EEE LPI is on - off). [6] - Tx Pause Mask. When 1
+ * indicates that the Tx Pause indication is disabled. When 0 indicates that
+ * the Tx Pause indication is enabled. [7] - BRB1 Empty Mask. When 1
+ * indicates that the BRB1 EMPTY indication is disabled. When 0 indicates
+ * that the BRB1 EMPTY indication is enabled. [8] - QM Idle Mask. When 1
+ * indicates that the QM IDLE indication is disabled. When 0 indicates that
+ * the QM IDLE indication is enabled. (One bit for both VOQ0 and VOQ1). [9]
+ * - QM LB Idle Mask. When 1 indicates that the QM IDLE indication for
+ * LOOPBACK is disabled. When 0 indicates that the QM IDLE indication for
+ * LOOPBACK is enabled. [10] - L1 Status Mask. When 1 indicates that the L1
+ * Status indication from the PCIE CORE is disabled. When 0 indicates that
+ * the RX EEE LPI Status indication from the PCIE CORE is enabled. In the
+ * EXIT Events Masks registers; this bit masks the falling edge detect of
+ * the L1 status (L1 is on - off). [11] - P0 E0 EEE EEE LPI REQ Mask. When
+ * =1 indicates that the P0 E0 EEE EEE LPI REQ indication is disabled. When
+ * =0 indicates that the P0 E0 EEE LPI REQ indication is enabled. [12] - P1
+ * E0 EEE LPI REQ Mask. When =1 indicates that the P0 EEE LPI REQ indication
+ * is disabled. When =0 indicates that the P0 EEE LPI REQ indication is
+ * enabled. [13] - P0 E1 EEE LPI REQ Mask. When =1 indicates that the P0 EEE
+ * LPI REQ indication is disabled. When =0 indicates that the P0 EEE LPI REQ
+ * indication is enabled. [14] - P1 E1 EEE LPI REQ Mask. When =1 indicates
+ * that the P0 EEE LPI REQ indication is disabled. When =0 indicates that
+ * the P0 EEE LPI REQ indication is enabled. [15] - L1 REQ Mask. When =1
+ * indicates that the L1 REQ indication is disabled. When =0 indicates that
+ * the L1 indication is enabled. [16] - Rx EEE LPI Status Edge Detect Mask.
+ * When =1 indicates that the RX EEE LPI Status Falling Edge Detect
+ * indication is disabled (Rx EEE LPI is on - off). When =0 indicates that
+ * the RX EEE LPI Status Falling Edge Detec indication is enabled (Rx EEE
+ * LPI is on - off). This bit is applicable only in the EXIT Events Masks
+ * registers. [17] - L1 Status Edge Detect Mask. When =1 indicates that the
+ * L1 Status Falling Edge Detect indication from the PCIE CORE is disabled
+ * (L1 is on - off). When =0 indicates that the L1 Status Falling Edge
+ * Detect indication from the PCIE CORE is enabled (L1 is on - off). This
+ * bit is applicable only in the EXIT Events Masks registers.Clock 25MHz.
+ * Reset on hard reset. */
+#define MISC_REG_CPMU_LP_MASK_EXT_P0 0xa888
+/* [RW 16] EEE LPI Entry Events Counter. A statistic counter with the number
+ * of counts that the SM entered the EEE LPI state. Clock 25MHz. Read only
+ * register. Reset on hard reset. */
+#define MISC_REG_CPMU_LP_SM_ENT_CNT_P0 0xa8b8
+/* [RW 16] EEE LPI Entry Events Counter. A statistic counter with the number
+ * of counts that the SM entered the EEE LPI state. Clock 25MHz. Read only
+ * register. Reset on hard reset. */
+#define MISC_REG_CPMU_LP_SM_ENT_CNT_P1 0xa8bc
+/* [RW 32] The following driver registers(1...16) represent 16 drivers and
+ 32 clients. Each client can be controlled by one driver only. One in each
+ bit represent that this driver control the appropriate client (Ex: bit 5
+ is set means this driver control client number 5). addr1 = set; addr0 =
+ clear; read from both addresses will give the same result = status. write
+ to address 1 will set a request to control all the clients that their
+ appropriate bit (in the write command) is set. if the client is free (the
+ appropriate bit in all the other drivers is clear) one will be written to
+ that driver register; if the client isn't free the bit will remain zero.
+ if the appropriate bit is set (the driver request to gain control on a
+ client it already controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW
+ interrupt will be asserted). write to address 0 will set a request to
+ free all the clients that their appropriate bit (in the write command) is
+ set. if the appropriate bit is clear (the driver request to free a client
+ it doesn't controls the ~MISC_REGISTERS_INT_STS.GENERIC_SW interrupt will
+ be asserted). */
+#define MISC_REG_DRIVER_CONTROL_1 0xa510
+#define MISC_REG_DRIVER_CONTROL_7 0xa3c8
+/* [RW 1] e1hmf for WOL. If clr WOL signal o the PXP will be send on bit 0
+ only. */
+#define MISC_REG_E1HMF_MODE 0xa5f8
+/* [R 1] Status of four port mode path swap input pin. */
+#define MISC_REG_FOUR_PORT_PATH_SWAP 0xa75c
+/* [RW 2] 4 port path swap overwrite.[0] - Overwrite control; if it is 0 -
+ the path_swap output is equal to 4 port mode path swap input pin; if it
+ is 1 - the path_swap output is equal to bit[1] of this register; [1] -
+ Overwrite value. If bit[0] of this register is 1 this is the value that
+ receives the path_swap output. Reset on Hard reset. */
+#define MISC_REG_FOUR_PORT_PATH_SWAP_OVWR 0xa738
+/* [R 1] Status of 4 port mode port swap input pin. */
+#define MISC_REG_FOUR_PORT_PORT_SWAP 0xa754
+/* [RW 2] 4 port port swap overwrite.[0] - Overwrite control; if it is 0 -
+ the port_swap output is equal to 4 port mode port swap input pin; if it
+ is 1 - the port_swap output is equal to bit[1] of this register; [1] -
+ Overwrite value. If bit[0] of this register is 1 this is the value that
+ receives the port_swap output. Reset on Hard reset. */
+#define MISC_REG_FOUR_PORT_PORT_SWAP_OVWR 0xa734
+/* [RW 32] Debug only: spare RW register reset by core reset */
+#define MISC_REG_GENERIC_CR_0 0xa460
+#define MISC_REG_GENERIC_CR_1 0xa464
+/* [RW 32] Debug only: spare RW register reset by por reset */
+#define MISC_REG_GENERIC_POR_1 0xa474
+/* [RW 32] Bit[0]: EPIO MODE SEL: Setting this bit to 1 will allow SW/FW to
+ use all of the 32 Extended GPIO pins. Without setting this bit; an EPIO
+ can not be configured as an output. Each output has its output enable in
+ the MCP register space; but this bit needs to be set to make use of that.
+ Bit[3:1] spare. Bit[4]: WCVTMON_PWRDN: Powerdown for Warpcore VTMON. When
+ set to 1 - Powerdown. Bit[5]: WCVTMON_RESETB: Reset for Warpcore VTMON.
+ When set to 0 - vTMON is in reset. Bit[6]: setting this bit will change
+ the i/o to an output and will drive the TimeSync output. Bit[31:7]:
+ spare. Global register. Reset by hard reset. */
+#define MISC_REG_GEN_PURP_HWG 0xa9a0
+/* [RW 32] GPIO. [31-28] FLOAT port 0; [27-24] FLOAT port 0; When any of
+ these bits is written as a '1'; the corresponding SPIO bit will turn off
+ it's drivers and become an input. This is the reset state of all GPIO
+ pins. The read value of these bits will be a '1' if that last command
+ (#SET; #CLR; or #FLOAT) for this bit was a #FLOAT. (reset value 0xff).
+ [23-20] CLR port 1; 19-16] CLR port 0; When any of these bits is written
+ as a '1'; the corresponding GPIO bit will drive low. The read value of
+ these bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for
+ this bit was a #CLR. (reset value 0). [15-12] SET port 1; 11-8] port 0;
+ SET When any of these bits is written as a '1'; the corresponding GPIO
+ bit will drive high (if it has that capability). The read value of these
+ bits will be a '1' if that last command (#SET; #CLR; or #FLOAT) for this
+ bit was a #SET. (reset value 0). [7-4] VALUE port 1; [3-0] VALUE port 0;
+ RO; These bits indicate the read value of each of the eight GPIO pins.
+ This is the result value of the pin; not the drive value. Writing these
+ bits will have not effect. */
+#define MISC_REG_GPIO 0xa490
+/* [RW 8] These bits enable the GPIO_INTs to signals event to the
+ IGU/MCP.according to the following map: [0] p0_gpio_0; [1] p0_gpio_1; [2]
+ p0_gpio_2; [3] p0_gpio_3; [4] p1_gpio_0; [5] p1_gpio_1; [6] p1_gpio_2;
+ [7] p1_gpio_3; */
+#define MISC_REG_GPIO_EVENT_EN 0xa2bc
+/* [RW 32] GPIO INT. [31-28] OLD_CLR port1; [27-24] OLD_CLR port0; Writing a
+ '1' to these bit clears the corresponding bit in the #OLD_VALUE register.
+ This will acknowledge an interrupt on the falling edge of corresponding
+ GPIO input (reset value 0). [23-16] OLD_SET [23-16] port1; OLD_SET port0;
+ Writing a '1' to these bit sets the corresponding bit in the #OLD_VALUE
+ register. This will acknowledge an interrupt on the rising edge of
+ corresponding SPIO input (reset value 0). [15-12] OLD_VALUE [11-8] port1;
+ OLD_VALUE port0; RO; These bits indicate the old value of the GPIO input
+ value. When the ~INT_STATE bit is set; this bit indicates the OLD value
+ of the pin such that if ~INT_STATE is set and this bit is '0'; then the
+ interrupt is due to a low to high edge. If ~INT_STATE is set and this bit
+ is '1'; then the interrupt is due to a high to low edge (reset value 0).
+ [7-4] INT_STATE port1; [3-0] INT_STATE RO port0; These bits indicate the
+ current GPIO interrupt state for each GPIO pin. This bit is cleared when
+ the appropriate #OLD_SET or #OLD_CLR command bit is written. This bit is
+ set when the GPIO input does not match the current value in #OLD_VALUE
+ (reset value 0). */
+#define MISC_REG_GPIO_INT 0xa494
+/* [R 28] this field hold the last information that caused reserved
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master that caused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_RSV_ATTN 0xa3c0
+/* [R 28] this field hold the last information that caused timeout
+ attention. bits [19:0] - address; [22:20] function; [23] reserved;
+ [27:24] the master that caused the attention - according to the following
+ encodeing:1 = pxp; 2 = mcp; 3 = usdm; 4 = tsdm; 5 = xsdm; 6 = csdm; 7 =
+ dbu; 8 = dmae */
+#define MISC_REG_GRC_TIMEOUT_ATTN 0xa3c4
+/* [RW 1] Setting this bit enables a timer in the GRC block to timeout any
+ access that does not finish within
+ ~misc_registers_grc_timout_val.grc_timeout_val cycles. When this bit is
+ cleared; this timeout is disabled. If this timeout occurs; the GRC shall
+ assert it attention output. */
+#define MISC_REG_GRC_TIMEOUT_EN 0xa280
+/* [RW 28] 28 LSB of LCPLL first register; reset val = 521. inside order of
+ the bits is: [2:0] OAC reset value 001) CML output buffer bias control;
+ 111 for +40%; 011 for +20%; 001 for 0%; 000 for -20%. [5:3] Icp_ctrl
+ (reset value 001) Charge pump current control; 111 for 720u; 011 for
+ 600u; 001 for 480u and 000 for 360u. [7:6] Bias_ctrl (reset value 00)
+ Global bias control; When bit 7 is high bias current will be 10 0gh; When
+ bit 6 is high bias will be 100w; Valid values are 00; 10; 01. [10:8]
+ Pll_observe (reset value 010) Bits to control observability. bit 10 is
+ for test bias; bit 9 is for test CK; bit 8 is test Vc. [12:11] Vth_ctrl
+ (reset value 00) Comparator threshold control. 00 for 0.6V; 01 for 0.54V
+ and 10 for 0.66V. [13] pllSeqStart (reset value 0) Enables VCO tuning
+ sequencer: 1= sequencer disabled; 0= sequencer enabled (inverted
+ internally). [14] reserved (reset value 0) Reset for VCO sequencer is
+ connected to RESET input directly. [15] capRetry_en (reset value 0)
+ enable retry on cap search failure (inverted). [16] freqMonitor_e (reset
+ value 0) bit to continuously monitor vco freq (inverted). [17]
+ freqDetRestart_en (reset value 0) bit to enable restart when not freq
+ locked (inverted). [18] freqDetRetry_en (reset value 0) bit to enable
+ retry on freq det failure(inverted). [19] pllForceFdone_en (reset value
+ 0) bit to enable pllForceFdone & pllForceFpass into pllSeq. [20]
+ pllForceFdone (reset value 0) bit to force freqDone. [21] pllForceFpass
+ (reset value 0) bit to force freqPass. [22] pllForceDone_en (reset value
+ 0) bit to enable pllForceCapDone. [23] pllForceCapDone (reset value 0)
+ bit to force capDone. [24] pllForceCapPass_en (reset value 0) bit to
+ enable pllForceCapPass. [25] pllForceCapPass (reset value 0) bit to force
+ capPass. [26] capRestart (reset value 0) bit to force cap sequencer to
+ restart. [27] capSelectM_en (reset value 0) bit to enable cap select
+ register bits. */
+#define MISC_REG_LCPLL_CTRL_1 0xa2a4
+#define MISC_REG_LCPLL_CTRL_REG_2 0xa2a8
+/* [RW 1] LCPLL power down. Global register. Active High. Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_PWRDWN 0xaa74
+/* [RW 1] LCPLL VCO reset. Global register. Active Low Reset on POR reset. */
+#define MISC_REG_LCPLL_E40_RESETB_ANA 0xaa78
+/* [RW 1] LCPLL post-divider reset. Global register. Active Low Reset on POR
+ * reset. */
+#define MISC_REG_LCPLL_E40_RESETB_DIG 0xaa7c
+/* [RW 4] Interrupt mask register #0 read/write */
+#define MISC_REG_MISC_INT_MASK 0xa388
+/* [RW 1] Parity mask register #0 read/write */
+#define MISC_REG_MISC_PRTY_MASK 0xa398
+/* [R 1] Parity register #0 read */
+#define MISC_REG_MISC_PRTY_STS 0xa38c
+/* [RC 1] Parity register #0 read clear */
+#define MISC_REG_MISC_PRTY_STS_CLR 0xa390
+#define MISC_REG_NIG_WOL_P0 0xa270
+#define MISC_REG_NIG_WOL_P1 0xa274
+/* [R 1] If set indicate that the pcie_rst_b was asserted without perst
+ assertion */
+#define MISC_REG_PCIE_HOT_RESET 0xa618
+/* [RW 32] 32 LSB of storm PLL first register; reset val = 0x 071d2911.
+ inside order of the bits is: [0] P1 divider[0] (reset value 1); [1] P1
+ divider[1] (reset value 0); [2] P1 divider[2] (reset value 0); [3] P1
+ divider[3] (reset value 0); [4] P2 divider[0] (reset value 1); [5] P2
+ divider[1] (reset value 0); [6] P2 divider[2] (reset value 0); [7] P2
+ divider[3] (reset value 0); [8] ph_det_dis (reset value 1); [9]
+ freq_det_dis (reset value 0); [10] Icpx[0] (reset value 0); [11] Icpx[1]
+ (reset value 1); [12] Icpx[2] (reset value 0); [13] Icpx[3] (reset value
+ 1); [14] Icpx[4] (reset value 0); [15] Icpx[5] (reset value 0); [16]
+ Rx[0] (reset value 1); [17] Rx[1] (reset value 0); [18] vc_en (reset
+ value 1); [19] vco_rng[0] (reset value 1); [20] vco_rng[1] (reset value
+ 1); [21] Kvco_xf[0] (reset value 0); [22] Kvco_xf[1] (reset value 0);
+ [23] Kvco_xf[2] (reset value 0); [24] Kvco_xs[0] (reset value 1); [25]
+ Kvco_xs[1] (reset value 1); [26] Kvco_xs[2] (reset value 1); [27]
+ testd_en (reset value 0); [28] testd_sel[0] (reset value 0); [29]
+ testd_sel[1] (reset value 0); [30] testd_sel[2] (reset value 0); [31]
+ testa_en (reset value 0); */
+#define MISC_REG_PLL_STORM_CTRL_1 0xa294
+#define MISC_REG_PLL_STORM_CTRL_2 0xa298
+#define MISC_REG_PLL_STORM_CTRL_3 0xa29c
+#define MISC_REG_PLL_STORM_CTRL_4 0xa2a0
+/* [R 1] Status of 4 port mode enable input pin. */
+#define MISC_REG_PORT4MODE_EN 0xa750
+/* [RW 2] 4 port mode enable overwrite.[0] - Overwrite control; if it is 0 -
+ * the port4mode_en output is equal to 4 port mode input pin; if it is 1 -
+ * the port4mode_en output is equal to bit[1] of this register; [1] -
+ * Overwrite value. If bit[0] of this register is 1 this is the value that
+ * receives the port4mode_en output . */
+#define MISC_REG_PORT4MODE_EN_OVWR 0xa720
+/* [RW 32] reset reg#2; rite/read one = the specific block is out of reset;
+ write/read zero = the specific block is in reset; addr 0-wr- the write
+ value will be written to the register; addr 1-set - one will be written
+ to all the bits that have the value of one in the data written (bits that
+ have the value of zero will not be change) ; addr 2-clear - zero will be
+ written to all the bits that have the value of one in the data written
+ (bits that have the value of zero will not be change); addr 3-ignore;
+ read ignore from all addr except addr 00; inside order of the bits is:
+ [0] rst_bmac0; [1] rst_bmac1; [2] rst_emac0; [3] rst_emac1; [4] rst_grc;
+ [5] rst_mcp_n_reset_reg_hard_core; [6] rst_ mcp_n_hard_core_rst_b; [7]
+ rst_ mcp_n_reset_cmn_cpu; [8] rst_ mcp_n_reset_cmn_core; [9] rst_rbcn;
+ [10] rst_dbg; [11] rst_misc_core; [12] rst_dbue (UART); [13]
+ Pci_resetmdio_n; [14] rst_emac0_hard_core; [15] rst_emac1_hard_core; 16]
+ rst_pxp_rq_rd_wr; 31:17] reserved */
+#define MISC_REG_RESET_REG_1 0xa580
+#define MISC_REG_RESET_REG_2 0xa590
+/* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is
+ shared with the driver resides */
+#define MISC_REG_SHARED_MEM_ADDR 0xa2b4
+/* [RW 32] SPIO. [31-24] FLOAT When any of these bits is written as a '1';
+ the corresponding SPIO bit will turn off it's drivers and become an
+ input. This is the reset state of all SPIO pins. The read value of these
+ bits will be a '1' if that last command (#SET; #CL; or #FLOAT) for this
+ bit was a #FLOAT. (reset value 0xff). [23-16] CLR When any of these bits
+ is written as a '1'; the corresponding SPIO bit will drive low. The read
+ value of these bits will be a '1' if that last command (#SET; #CLR; or
+#FLOAT) for this bit was a #CLR. (reset value 0). [15-8] SET When any of
+ these bits is written as a '1'; the corresponding SPIO bit will drive
+ high (if it has that capability). The read value of these bits will be a
+ '1' if that last command (#SET; #CLR; or #FLOAT) for this bit was a #SET.
+ (reset value 0). [7-0] VALUE RO; These bits indicate the read value of
+ each of the eight SPIO pins. This is the result value of the pin; not the
+ drive value. Writing these bits will have not effect. Each 8 bits field
+ is divided as follows: [0] VAUX Enable; when pulsed low; enables supply
+ from VAUX. (This is an output pin only; the FLOAT field is not applicable
+ for this pin); [1] VAUX Disable; when pulsed low; disables supply form
+ VAUX. (This is an output pin only; FLOAT field is not applicable for this
+ pin); [2] SEL_VAUX_B - Control to power switching logic. Drive low to
+ select VAUX supply. (This is an output pin only; it is not controlled by
+ the SET and CLR fields; it is controlled by the Main Power SM; the FLOAT
+ field is not applicable for this pin; only the VALUE fields is relevant -
+ it reflects the output value); [3] port swap [4] spio_4; [5] spio_5; [6]
+ Bit 0 of UMP device ID select; read by UMP firmware; [7] Bit 1 of UMP
+ device ID select; read by UMP firmware. */
+#define MISC_REG_SPIO 0xa4fc
+/* [RW 8] These bits enable the SPIO_INTs to signals event to the IGU/MC.
+ according to the following map: [3:0] reserved; [4] spio_4 [5] spio_5;
+ [7:0] reserved */
+#define MISC_REG_SPIO_EVENT_EN 0xa2b8
+/* [RW 32] SPIO INT. [31-24] OLD_CLR Writing a '1' to these bit clears the
+ corresponding bit in the #OLD_VALUE register. This will acknowledge an
+ interrupt on the falling edge of corresponding SPIO input (reset value
+ 0). [23-16] OLD_SET Writing a '1' to these bit sets the corresponding bit
+ in the #OLD_VALUE register. This will acknowledge an interrupt on the
+ rising edge of corresponding SPIO input (reset value 0). [15-8] OLD_VALUE
+ RO; These bits indicate the old value of the SPIO input value. When the
+ ~INT_STATE bit is set; this bit indicates the OLD value of the pin such
+ that if ~INT_STATE is set and this bit is '0'; then the interrupt is due
+ to a low to high edge. If ~INT_STATE is set and this bit is '1'; then the
+ interrupt is due to a high to low edge (reset value 0). [7-0] INT_STATE
+ RO; These bits indicate the current SPIO interrupt state for each SPIO
+ pin. This bit is cleared when the appropriate #OLD_SET or #OLD_CLR
+ command bit is written. This bit is set when the SPIO input does not
+ match the current value in #OLD_VALUE (reset value 0). */
+#define MISC_REG_SPIO_INT 0xa500
+/* [RW 32] reload value for counter 4 if reload; the value will be reload if
+ the counter reached zero and the reload bit
+ (~misc_registers_sw_timer_cfg_4.sw_timer_cfg_4[1] ) is set */
+#define MISC_REG_SW_TIMER_RELOAD_VAL_4 0xa2fc
+/* [RW 32] the value of the counter for sw timers1-8. there are 8 addresses
+ in this register. address 0 - timer 1; address 1 - timer 2, ... address 7 -
+ timer 8 */
+#define MISC_REG_SW_TIMER_VAL 0xa5c0
+/* [R 1] Status of two port mode path swap input pin. */
+#define MISC_REG_TWO_PORT_PATH_SWAP 0xa758
+/* [RW 2] 2 port swap overwrite.[0] - Overwrite control; if it is 0 - the
+ path_swap output is equal to 2 port mode path swap input pin; if it is 1
+ - the path_swap output is equal to bit[1] of this register; [1] -
+ Overwrite value. If bit[0] of this register is 1 this is the value that
+ receives the path_swap output. Reset on Hard reset. */
+#define MISC_REG_TWO_PORT_PATH_SWAP_OVWR 0xa72c
+/* [RW 1] Set by the MCP to remember if one or more of the drivers is/are
+ loaded; 0-prepare; -unprepare */
+#define MISC_REG_UNPREPARED 0xa424
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST (0x1<<0)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST (0x1<<1)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN (0x1<<4)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST (0x1<<2)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN (0x1<<3)
+/* [RW 5] MDIO PHY Address. The WC uses this address to determine whether or
+ * not it is the recipient of the message on the MDIO interface. The value
+ * is compared to the value on ctrl_md_devad. Drives output
+ * misc_xgxs0_phy_addr. Global register. */
+#define MISC_REG_WC0_CTRL_PHY_ADDR 0xa9cc
+#define MISC_REG_WC0_RESET 0xac30
+/* [RW 2] XMAC Core port mode. Indicates the number of ports on the system
+ side. This should be less than or equal to phy_port_mode; if some of the
+ ports are not used. This enables reduction of frequency on the core side.
+ This is a strap input for the XMAC_MP core. 00 - Single Port Mode; 01 -
+ Dual Port Mode; 10 - Tri Port Mode; 11 - Quad Port Mode. This is a strap
+ input for the XMAC_MP core; and should be changed only while reset is
+ held low. Reset on Hard reset. */
+#define MISC_REG_XMAC_CORE_PORT_MODE 0xa964
+/* [RW 2] XMAC PHY port mode. Indicates the number of ports on the Warp
+ Core. This is a strap input for the XMAC_MP core. 00 - Single Port Mode;
+ 01 - Dual Port Mode; 1x - Quad Port Mode; This is a strap input for the
+ XMAC_MP core; and should be changed only while reset is held low. Reset
+ on Hard reset. */
+#define MISC_REG_XMAC_PHY_PORT_MODE 0xa960
+/* [RW 32] 1 [47] Packet Size = 64 Write to this register write bits 31:0.
+ * Reads from this register will clear bits 31:0. */
+#define MSTAT_REG_RX_STAT_GR64_LO 0x200
+/* [RW 32] 1 [00] Tx Good Packet Count Write to this register write bits
+ * 31:0. Reads from this register will clear bits 31:0. */
+#define MSTAT_REG_TX_STAT_GTXPOK_LO 0
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST (0x1<<0)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST (0x1<<1)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN (0x1<<4)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST (0x1<<2)
+#define NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN (0x1<<3)
+#define NIG_LLH0_XCM_MASK_REG_LLH0_XCM_MASK_BCN (0x1<<0)
+#define NIG_LLH1_XCM_MASK_REG_LLH1_XCM_MASK_BCN (0x1<<0)
+#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_EMAC0_MISC_MI_INT (0x1<<0)
+#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_SERDES0_LINK_STATUS (0x1<<9)
+#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK10G (0x1<<15)
+#define NIG_MASK_INTERRUPT_PORT0_REG_MASK_XGXS0_LINK_STATUS (0xf<<18)
+/* [RW 1] Input enable for RX_BMAC0 IF */
+#define NIG_REG_BMAC0_IN_EN 0x100ac
+/* [RW 1] output enable for TX_BMAC0 IF */
+#define NIG_REG_BMAC0_OUT_EN 0x100e0
+/* [RW 1] output enable for TX BMAC pause port 0 IF */
+#define NIG_REG_BMAC0_PAUSE_OUT_EN 0x10110
+/* [RW 1] output enable for RX_BMAC0_REGS IF */
+#define NIG_REG_BMAC0_REGS_OUT_EN 0x100e8
+/* [RW 1] output enable for RX BRB1 port0 IF */
+#define NIG_REG_BRB0_OUT_EN 0x100f8
+/* [RW 1] Input enable for TX BRB1 pause port 0 IF */
+#define NIG_REG_BRB0_PAUSE_IN_EN 0x100c4
+/* [RW 1] output enable for RX BRB1 port1 IF */
+#define NIG_REG_BRB1_OUT_EN 0x100fc
+/* [RW 1] Input enable for TX BRB1 pause port 1 IF */
+#define NIG_REG_BRB1_PAUSE_IN_EN 0x100c8
+/* [RW 1] output enable for RX BRB1 LP IF */
+#define NIG_REG_BRB_LB_OUT_EN 0x10100
+/* [WB_W 82] Debug packet to LP from RBC; Data spelling:[63:0] data; 64]
+ error; [67:65]eop_bvalid; [68]eop; [69]sop; [70]port_id; 71]flush;
+ 72:73]-vnic_num; 81:74]-sideband_info */
+#define NIG_REG_DEBUG_PACKET_LB 0x10800
+/* [RW 1] Input enable for TX Debug packet */
+#define NIG_REG_EGRESS_DEBUG_IN_EN 0x100dc
+/* [RW 1] If 1 - egress drain mode for port0 is active. In this mode all
+ packets from PBFare not forwarded to the MAC and just deleted from FIFO.
+ First packet may be deleted from the middle. And last packet will be
+ always deleted till the end. */
+#define NIG_REG_EGRESS_DRAIN0_MODE 0x10060
+/* [RW 1] Output enable to EMAC0 */
+#define NIG_REG_EGRESS_EMAC0_OUT_EN 0x10120
+/* [RW 1] MAC configuration for packets of port0. If 1 - all packet outputs
+ to emac for port0; other way to bmac for port0 */
+#define NIG_REG_EGRESS_EMAC0_PORT 0x10058
+/* [RW 1] Input enable for TX PBF user packet port0 IF */
+#define NIG_REG_EGRESS_PBF0_IN_EN 0x100cc
+/* [RW 1] Input enable for TX PBF user packet port1 IF */
+#define NIG_REG_EGRESS_PBF1_IN_EN 0x100d0
+/* [RW 1] Input enable for TX UMP management packet port0 IF */
+#define NIG_REG_EGRESS_UMP0_IN_EN 0x100d4
+/* [RW 1] Input enable for RX_EMAC0 IF */
+#define NIG_REG_EMAC0_IN_EN 0x100a4
+/* [RW 1] output enable for TX EMAC pause port 0 IF */
+#define NIG_REG_EMAC0_PAUSE_OUT_EN 0x10118
+/* [R 1] status from emac0. This bit is set when MDINT from either the
+ EXT_MDINT pin or from the Copper PHY is driven low. This condition must
+ be cleared in the attached PHY device that is driving the MINT pin. */
+#define NIG_REG_EMAC0_STATUS_MISC_MI_INT 0x10494
+/* [WB 48] This address space contains BMAC0 registers. The BMAC registers
+ are described in appendix A. In order to access the BMAC0 registers; the
+ base address; NIG_REGISTERS_INGRESS_BMAC0_MEM; Offset: 0x10c00; should be
+ added to each BMAC register offset */
+#define NIG_REG_INGRESS_BMAC0_MEM 0x10c00
+/* [WB 48] This address space contains BMAC1 registers. The BMAC registers
+ are described in appendix A. In order to access the BMAC0 registers; the
+ base address; NIG_REGISTERS_INGRESS_BMAC1_MEM; Offset: 0x11000; should be
+ added to each BMAC register offset */
+#define NIG_REG_INGRESS_BMAC1_MEM 0x11000
+/* [R 1] FIFO empty in EOP descriptor FIFO of LP in NIG_RX_EOP */
+#define NIG_REG_INGRESS_EOP_LB_EMPTY 0x104e0
+/* [RW 17] Debug only. RX_EOP_DSCR_lb_FIFO in NIG_RX_EOP. Data
+ packet_length[13:0]; mac_error[14]; trunc_error[15]; parity[16] */
+#define NIG_REG_INGRESS_EOP_LB_FIFO 0x104e4
+/* [RW 27] 0 - must be active for Everest A0; 1- for Everest B0 when latch
+ logic for interrupts must be used. Enable per bit of interrupt of
+ ~latch_status.latch_status */
+#define NIG_REG_LATCH_BC_0 0x16210
+/* [RW 27] Latch for each interrupt from Unicore.b[0]
+ status_emac0_misc_mi_int; b[1] status_emac0_misc_mi_complete;
+ b[2]status_emac0_misc_cfg_change; b[3]status_emac0_misc_link_status;
+ b[4]status_emac0_misc_link_change; b[5]status_emac0_misc_attn;
+ b[6]status_serdes0_mac_crs; b[7]status_serdes0_autoneg_complete;
+ b[8]status_serdes0_fiber_rxact; b[9]status_serdes0_link_status;
+ b[10]status_serdes0_mr_page_rx; b[11]status_serdes0_cl73_an_complete;
+ b[12]status_serdes0_cl73_mr_page_rx; b[13]status_serdes0_rx_sigdet;
+ b[14]status_xgxs0_remotemdioreq; b[15]status_xgxs0_link10g;
+ b[16]status_xgxs0_autoneg_complete; b[17]status_xgxs0_fiber_rxact;
+ b[21:18]status_xgxs0_link_status; b[22]status_xgxs0_mr_page_rx;
+ b[23]status_xgxs0_cl73_an_complete; b[24]status_xgxs0_cl73_mr_page_rx;
+ b[25]status_xgxs0_rx_sigdet; b[26]status_xgxs0_mac_crs */
+#define NIG_REG_LATCH_STATUS_0 0x18000
+/* [RW 1] led 10g for port 0 */
+#define NIG_REG_LED_10G_P0 0x10320
+/* [RW 1] led 10g for port 1 */
+#define NIG_REG_LED_10G_P1 0x10324
+/* [RW 1] Port0: This bit is set to enable the use of the
+ ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 field
+ defined below. If this bit is cleared; then the blink rate will be about
+ 8Hz. */
+#define NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 0x10318
+/* [RW 12] Port0: Specifies the period of each blink cycle (on + off) for
+ Traffic LED in milliseconds. Must be a non-zero value. This 12-bit field
+ is reset to 0x080; giving a default blink period of approximately 8Hz. */
+#define NIG_REG_LED_CONTROL_BLINK_RATE_P0 0x10310
+/* [RW 1] Port0: If set along with the
+ ~nig_registers_led_control_override_traffic_p0.led_control_override_traffic_p0
+ bit and ~nig_registers_led_control_traffic_p0.led_control_traffic_p0 LED
+ bit; the Traffic LED will blink with the blink rate specified in
+ ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and
+ ~nig_registers_led_control_blink_rate_ena_p0.led_control_blink_rate_ena_p0
+ fields. */
+#define NIG_REG_LED_CONTROL_BLINK_TRAFFIC_P0 0x10308
+/* [RW 1] Port0: If set overrides hardware control of the Traffic LED. The
+ Traffic LED will then be controlled via bit ~nig_registers_
+ led_control_traffic_p0.led_control_traffic_p0 and bit
+ ~nig_registers_led_control_blink_traffic_p0.led_control_blink_traffic_p0 */
+#define NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0 0x102f8
+/* [RW 1] Port0: If set along with the led_control_override_trafic_p0 bit;
+ turns on the Traffic LED. If the led_control_blink_traffic_p0 bit is also
+ set; the LED will blink with blink rate specified in
+ ~nig_registers_led_control_blink_rate_p0.led_control_blink_rate_p0 and
+ ~nig_regsters_led_control_blink_rate_ena_p0.led_control_blink_rate_ena_p0
+ fields. */
+#define NIG_REG_LED_CONTROL_TRAFFIC_P0 0x10300
+/* [RW 4] led mode for port0: 0 MAC; 1-3 PHY1; 4 MAC2; 5-7 PHY4; 8-MAC3;
+ 9-11PHY7; 12 MAC4; 13-15 PHY10; */
+#define NIG_REG_LED_MODE_P0 0x102f0
+/* [RW 3] for port0 enable for llfc ppp and pause. b0 - brb1 enable; b1-
+ tsdm enable; b2- usdm enable */
+#define NIG_REG_LLFC_EGRESS_SRC_ENABLE_0 0x16070
+#define NIG_REG_LLFC_EGRESS_SRC_ENABLE_1 0x16074
+/* [RW 1] SAFC enable for port0. This register may get 1 only when
+ ~ppp_enable.ppp_enable = 0 and pause_enable.pause_enable =0 for the same
+ port */
+#define NIG_REG_LLFC_ENABLE_0 0x16208
+#define NIG_REG_LLFC_ENABLE_1 0x1620c
+/* [RW 16] classes are high-priority for port0 */
+#define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_0 0x16058
+#define NIG_REG_LLFC_HIGH_PRIORITY_CLASSES_1 0x1605c
+/* [RW 16] classes are low-priority for port0 */
+#define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_0 0x16060
+#define NIG_REG_LLFC_LOW_PRIORITY_CLASSES_1 0x16064
+/* [RW 1] Output enable of message to LLFC BMAC IF for port0 */
+#define NIG_REG_LLFC_OUT_EN_0 0x160c8
+#define NIG_REG_LLFC_OUT_EN_1 0x160cc
+#define NIG_REG_LLH0_ACPI_PAT_0_CRC 0x1015c
+#define NIG_REG_LLH0_ACPI_PAT_6_LEN 0x10154
+#define NIG_REG_LLH0_BRB1_DRV_MASK 0x10244
+#define NIG_REG_LLH0_BRB1_DRV_MASK_MF 0x16048
+/* [RW 1] send to BRB1 if no match on any of RMP rules. */
+#define NIG_REG_LLH0_BRB1_NOT_MCP 0x1025c
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH0_CLS_TYPE 0x16080
+/* [RW 32] cm header for llh0 */
+#define NIG_REG_LLH0_CM_HEADER 0x1007c
+#define NIG_REG_LLH0_DEST_IP_0_1 0x101dc
+#define NIG_REG_LLH0_DEST_MAC_0_0 0x101c0
+/* [RW 16] destination TCP address 1. The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_TCP_0 0x10220
+/* [RW 16] destination UDP address 1 The LLH will look for this address in
+ all incoming packets. */
+#define NIG_REG_LLH0_DEST_UDP_0 0x10214
+#define NIG_REG_LLH0_ERROR_MASK 0x1008c
+/* [RW 8] event id for llh0 */
+#define NIG_REG_LLH0_EVENT_ID 0x10084
+#define NIG_REG_LLH0_FUNC_EN 0x160fc
+#define NIG_REG_LLH0_FUNC_MEM 0x16180
+#define NIG_REG_LLH0_FUNC_MEM_ENABLE 0x16140
+#define NIG_REG_LLH0_FUNC_VLAN_ID 0x16100
+/* [RW 1] Determine the IP version to look for in
+ ~nig_registers_llh0_dest_ip_0.llh0_dest_ip_0. 0 - IPv6; 1-IPv4 */
+#define NIG_REG_LLH0_IPV4_IPV6_0 0x10208
+/* [RW 1] t bit for llh0 */
+#define NIG_REG_LLH0_T_BIT 0x10074
+/* [RW 12] VLAN ID 1. In case of VLAN packet the LLH will look for this ID. */
+#define NIG_REG_LLH0_VLAN_ID_0 0x1022c
+/* [RW 8] init credit counter for port0 in LLH */
+#define NIG_REG_LLH0_XCM_INIT_CREDIT 0x10554
+#define NIG_REG_LLH0_XCM_MASK 0x10130
+#define NIG_REG_LLH1_BRB1_DRV_MASK 0x10248
+/* [RW 1] send to BRB1 if no match on any of RMP rules. */
+#define NIG_REG_LLH1_BRB1_NOT_MCP 0x102dc
+/* [RW 2] Determine the classification participants. 0: no classification.1:
+ classification upon VLAN id. 2: classification upon MAC address. 3:
+ classification upon both VLAN id & MAC addr. */
+#define NIG_REG_LLH1_CLS_TYPE 0x16084
+/* [RW 32] cm header for llh1 */
+#define NIG_REG_LLH1_CM_HEADER 0x10080
+#define NIG_REG_LLH1_ERROR_MASK 0x10090
+/* [RW 8] event id for llh1 */
+#define NIG_REG_LLH1_EVENT_ID 0x10088
+#define NIG_REG_LLH1_FUNC_EN 0x16104
+#define NIG_REG_LLH1_FUNC_MEM 0x161c0
+#define NIG_REG_LLH1_FUNC_MEM_ENABLE 0x16160
+#define NIG_REG_LLH1_FUNC_MEM_SIZE 16
+/* [RW 1] When this bit is set; the LLH will classify the packet before
+ * sending it to the BRB or calculating WoL on it. This bit controls port 1
+ * only. The legacy llh_multi_function_mode bit controls port 0. */
+#define NIG_REG_LLH1_MF_MODE 0x18614
+/* [RW 8] init credit counter for port1 in LLH */
+#define NIG_REG_LLH1_XCM_INIT_CREDIT 0x10564
+#define NIG_REG_LLH1_XCM_MASK 0x10134
+/* [RW 1] When this bit is set; the LLH will expect all packets to be with
+ e1hov */
+#define NIG_REG_LLH_E1HOV_MODE 0x160d8
+/* [RW 1] When this bit is set; the LLH will classify the packet before
+ sending it to the BRB or calculating WoL on it. */
+#define NIG_REG_LLH_MF_MODE 0x16024
+#define NIG_REG_MASK_INTERRUPT_PORT0 0x10330
+#define NIG_REG_MASK_INTERRUPT_PORT1 0x10334
+/* [RW 1] Output signal from NIG to EMAC0. When set enables the EMAC0 block. */
+#define NIG_REG_NIG_EMAC0_EN 0x1003c
+/* [RW 1] Output signal from NIG to EMAC1. When set enables the EMAC1 block. */
+#define NIG_REG_NIG_EMAC1_EN 0x10040
+/* [RW 1] Output signal from NIG to TX_EMAC0. When set indicates to the
+ EMAC0 to strip the CRC from the ingress packets. */
+#define NIG_REG_NIG_INGRESS_EMAC0_NO_CRC 0x10044
+/* [R 32] Interrupt register #0 read */
+#define NIG_REG_NIG_INT_STS_0 0x103b0
+#define NIG_REG_NIG_INT_STS_1 0x103c0
+/* [RC 32] Interrupt register #0 read clear */
+#define NIG_REG_NIG_INT_STS_CLR_0 0x103b4
+/* [R 32] Legacy E1 and E1H location for parity error mask register. */
+#define NIG_REG_NIG_PRTY_MASK 0x103dc
+/* [RW 32] Parity mask register #0 read/write */
+#define NIG_REG_NIG_PRTY_MASK_0 0x183c8
+#define NIG_REG_NIG_PRTY_MASK_1 0x183d8
+/* [R 32] Legacy E1 and E1H location for parity error status register. */
+#define NIG_REG_NIG_PRTY_STS 0x103d0
+/* [R 32] Parity register #0 read */
+#define NIG_REG_NIG_PRTY_STS_0 0x183bc
+#define NIG_REG_NIG_PRTY_STS_1 0x183cc
+/* [R 32] Legacy E1 and E1H location for parity error status clear register. */
+#define NIG_REG_NIG_PRTY_STS_CLR 0x103d4
+/* [RC 32] Parity register #0 read clear */
+#define NIG_REG_NIG_PRTY_STS_CLR_0 0x183c0
+#define NIG_REG_NIG_PRTY_STS_CLR_1 0x183d0
+#define MCPR_IMC_COMMAND_ENABLE (1L<<31)
+#define MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT 16
+#define MCPR_IMC_COMMAND_OPERATION_BITSHIFT 28
+#define MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT 8
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
+ * Ethernet header. */
+#define NIG_REG_P0_HDRS_AFTER_BASIC 0x18038
+/* [RW 1] HW PFC enable bit. Set this bit to enable the PFC functionality in
+ * the NIG. Other flow control modes such as PAUSE and SAFC/LLFC should be
+ * disabled when this bit is set. */
+#define NIG_REG_P0_HWPFC_ENABLE 0x18078
+#define NIG_REG_P0_LLH_FUNC_MEM2 0x18480
+#define NIG_REG_P0_LLH_FUNC_MEM2_ENABLE 0x18440
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_SEQID 0x1875c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_LSB 0x18754
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_LLH_PTP_HOST_BUF_TS_MSB 0x18758
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_LLH_PTP_PARAM_MASK 0x187a0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P0_LLH_PTP_RULE_MASK 0x187a4
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P0_LLH_PTP_TO_HOST 0x187ac
+/* [RW 1] Input enable for RX MAC interface. */
+#define NIG_REG_P0_MAC_IN_EN 0x185ac
+/* [RW 1] Output enable for TX MAC interface */
+#define NIG_REG_P0_MAC_OUT_EN 0x185b0
+/* [RW 1] Output enable for TX PAUSE signal to the MAC. */
+#define NIG_REG_P0_MAC_PAUSE_OUT_EN 0x185b4
+/* [RW 32] Eight 4-bit configurations for specifying which COS (0-15 for
+ * future expansion) each priorty is to be mapped to. Bits 3:0 specify the
+ * COS for priority 0. Bits 31:28 specify the COS for priority 7. The 3-bit
+ * priority field is extracted from the outer-most VLAN in receive packet.
+ * Only COS 0 and COS 1 are supported in E2. */
+#define NIG_REG_P0_PKT_PRIORITY_TO_COS 0x18054
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P0_PTP_EN 0x18788
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
+ * priority is mapped to COS 0 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS0_PRIORITY_MASK 0x18058
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 1. A
+ * priority is mapped to COS 1 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS1_PRIORITY_MASK 0x1805c
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 2. A
+ * priority is mapped to COS 2 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS2_PRIORITY_MASK 0x186b0
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 3. A
+ * priority is mapped to COS 3 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS3_PRIORITY_MASK 0x186b4
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 4. A
+ * priority is mapped to COS 4 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS4_PRIORITY_MASK 0x186b8
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 5. A
+ * priority is mapped to COS 5 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P0_RX_COS5_PRIORITY_MASK 0x186bc
+/* [R 1] RX FIFO for receiving data from MAC is empty. */
+/* [RW 15] Specify which of the credit registers the client is to be mapped
+ * to. Bits[2:0] are for client 0; bits [14:12] are for client 4. For
+ * clients that are not subject to WFQ credit blocking - their
+ * specifications here are not used. */
+#define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP 0x180f0
+/* [RW 32] Specify which of the credit registers the client is to be mapped
+ * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are
+ * for client 0; bits [35:32] are for client 8. For clients that are not
+ * subject to WFQ credit blocking - their specifications here are not used.
+ * This is a new register (with 2_) added in E3 B0 to accommodate the 9
+ * input clients to ETS arbiter. The reset default is set for management and
+ * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to
+ * use credit registers 0-5 respectively (0x543210876). Note that credit
+ * registers can not be shared between clients. */
+#define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_LSB 0x18688
+/* [RW 4] Specify which of the credit registers the client is to be mapped
+ * to. This register specifies bits 35:32 of the 36-bit value. Bits[3:0] are
+ * for client 0; bits [35:32] are for client 8. For clients that are not
+ * subject to WFQ credit blocking - their specifications here are not used.
+ * This is a new register (with 2_) added in E3 B0 to accommodate the 9
+ * input clients to ETS arbiter. The reset default is set for management and
+ * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to
+ * use credit registers 0-5 respectively (0x543210876). Note that credit
+ * registers can not be shared between clients. */
+#define NIG_REG_P0_TX_ARB_CLIENT_CREDIT_MAP2_MSB 0x1868c
+/* [RW 5] Specify whether the client competes directly in the strict
+ * priority arbiter. The bits are mapped according to client ID (client IDs
+ * are defined in tx_arb_priority_client). Default value is set to enable
+ * strict priorities for clients 0-2 -- management and debug traffic. */
+#define NIG_REG_P0_TX_ARB_CLIENT_IS_STRICT 0x180e8
+/* [RW 5] Specify whether the client is subject to WFQ credit blocking. The
+ * bits are mapped according to client ID (client IDs are defined in
+ * tx_arb_priority_client). Default value is 0 for not using WFQ credit
+ * blocking. */
+#define NIG_REG_P0_TX_ARB_CLIENT_IS_SUBJECT2WFQ 0x180ec
+/* [RW 32] Specify the upper bound that credit register 0 is allowed to
+ * reach. */
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_0 0x1810c
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_1 0x18110
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_2 0x18114
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_3 0x18118
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_4 0x1811c
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_5 0x186a0
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_6 0x186a4
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_7 0x186a8
+#define NIG_REG_P0_TX_ARB_CREDIT_UPPER_BOUND_8 0x186ac
+/* [RW 32] Specify the weight (in bytes) to be added to credit register 0
+ * when it is time to increment. */
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_0 0x180f8
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_1 0x180fc
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_2 0x18100
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_3 0x18104
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_4 0x18108
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_5 0x18690
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_6 0x18694
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_7 0x18698
+#define NIG_REG_P0_TX_ARB_CREDIT_WEIGHT_8 0x1869c
+/* [RW 12] Specify the number of strict priority arbitration slots between
+ * two round-robin arbitration slots to avoid starvation. A value of 0 means
+ * no strict priority cycles - the strict priority with anti-starvation
+ * arbiter becomes a round-robin arbiter. */
+#define NIG_REG_P0_TX_ARB_NUM_STRICT_ARB_SLOTS 0x180f4
+/* [RW 15] Specify the client number to be assigned to each priority of the
+ * strict priority arbiter. Priority 0 is the highest priority. Bits [2:0]
+ * are for priority 0 client; bits [14:12] are for priority 4 client. The
+ * clients are assigned the following IDs: 0-management; 1-debug traffic
+ * from this port; 2-debug traffic from other port; 3-COS0 traffic; 4-COS1
+ * traffic. The reset value[14:0] is set to 0x4688 (15'b100_011_010_001_000)
+ * for management at priority 0; debug traffic at priorities 1 and 2; COS0
+ * traffic at priority 3; and COS1 traffic at priority 4. */
+#define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT 0x180e4
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
+ * Ethernet header. */
+#define NIG_REG_P1_HDRS_AFTER_BASIC 0x1818c
+#define NIG_REG_P1_LLH_FUNC_MEM2 0x184c0
+#define NIG_REG_P1_LLH_FUNC_MEM2_ENABLE 0x18460a
+/* [RW 17] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. Bits [15:0] return the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Writing a 1 to bit 16
+ * will clear the buffer.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_SEQID 0x18774
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_LSB 0x1876c
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * the host. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_LLH_PTP_HOST_BUF_TS_MSB 0x18770
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_LLH_PTP_PARAM_MASK 0x187c8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules. Note that rules 0-3 are for IPv4
+ * packets only and require that the packet is IPv4 for the rules to match.
+ * Note that rules 4-7 are for IPv6 packets only and require that the packet
+ * is IPv6 for the rules to match.
+ */
+#define NIG_REG_P1_LLH_PTP_RULE_MASK 0x187cc
+/* [RW 1] Set to 1 to enable PTP packets to be forwarded to the host. */
+#define NIG_REG_P1_LLH_PTP_TO_HOST 0x187d4
+/* [RW 32] Specify the client number to be assigned to each priority of the
+ * strict priority arbiter. This register specifies bits 31:0 of the 36-bit
+ * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
+ * client; bits [35-32] are for priority 8 client. The clients are assigned
+ * the following IDs: 0-management; 1-debug traffic from this port; 2-debug
+ * traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic;
+ * 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is
+ * set to 0x345678021. This is a new register (with 2_) added in E3 B0 to
+ * accommodate the 9 input clients to ETS arbiter. */
+#define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_LSB 0x18680
+/* [RW 4] Specify the client number to be assigned to each priority of the
+ * strict priority arbiter. This register specifies bits 35:32 of the 36-bit
+ * value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
+ * client; bits [35-32] are for priority 8 client. The clients are assigned
+ * the following IDs: 0-management; 1-debug traffic from this port; 2-debug
+ * traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic;
+ * 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is
+ * set to 0x345678021. This is a new register (with 2_) added in E3 B0 to
+ * accommodate the 9 input clients to ETS arbiter. */
+#define NIG_REG_P0_TX_ARB_PRIORITY_CLIENT2_MSB 0x18684
+/* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP
+ * packets to BRB LB interface to forward the packet to the host. All
+ * packets from MCP are forwarded to the network when this bit is cleared -
+ * regardless of the configured destination in tx_mng_destination register.
+ * When MCP-to-host paths for both ports 0 and 1 are disabled - the arbiter
+ * for BRB LB interface is bypassed and PBF LB traffic is always selected to
+ * send to BRB LB.
+ */
+#define NIG_REG_P0_TX_MNG_HOST_ENABLE 0x182f4
+#define NIG_REG_P1_HWPFC_ENABLE 0x181d0
+#define NIG_REG_P1_MAC_IN_EN 0x185c0
+/* [RW 1] Output enable for TX MAC interface */
+#define NIG_REG_P1_MAC_OUT_EN 0x185c4
+/* [RW 1] Output enable for TX PAUSE signal to the MAC. */
+#define NIG_REG_P1_MAC_PAUSE_OUT_EN 0x185c8
+/* [RW 32] Eight 4-bit configurations for specifying which COS (0-15 for
+ * future expansion) each priorty is to be mapped to. Bits 3:0 specify the
+ * COS for priority 0. Bits 31:28 specify the COS for priority 7. The 3-bit
+ * priority field is extracted from the outer-most VLAN in receive packet.
+ * Only COS 0 and COS 1 are supported in E2. */
+#define NIG_REG_P1_PKT_PRIORITY_TO_COS 0x181a8
+/* [RW 6] Enable for TimeSync feature. Bits [2:0] are for RX side. Bits
+ * [5:3] are for TX side. Bit 0 enables TimeSync on RX side. Bit 1 enables
+ * V1 frame format in timesync event detection on RX side. Bit 2 enables V2
+ * frame format in timesync event detection on RX side. Bit 3 enables
+ * TimeSync on TX side. Bit 4 enables V1 frame format in timesync event
+ * detection on TX side. Bit 5 enables V2 frame format in timesync event
+ * detection on TX side. Note that for HW to detect PTP packet and extract
+ * data from the packet, at least one of the version bits of that traffic
+ * direction has to be enabled.
+ */
+#define NIG_REG_P1_PTP_EN 0x187b0
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 0. A
+ * priority is mapped to COS 0 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P1_RX_COS0_PRIORITY_MASK 0x181ac
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 1. A
+ * priority is mapped to COS 1 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P1_RX_COS1_PRIORITY_MASK 0x181b0
+/* [RW 16] Bit-map indicating which SAFC/PFC priorities to map to COS 2. A
+ * priority is mapped to COS 2 when the corresponding mask bit is 1. More
+ * than one bit may be set; allowing multiple priorities to be mapped to one
+ * COS. */
+#define NIG_REG_P1_RX_COS2_PRIORITY_MASK 0x186f8
+/* [R 1] RX FIFO for receiving data from MAC is empty. */
+#define NIG_REG_P1_RX_MACFIFO_EMPTY 0x1858c
+/* [R 1] TLLH FIFO is empty. */
+#define NIG_REG_P1_TLLH_FIFO_EMPTY 0x18338
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_SEQID 0x187e0
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_LSB 0x187d8
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P0_TLLH_PTP_BUF_TS_MSB 0x187dc
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P0_TLLH_PTP_PARAM_MASK 0x187f0
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P0_TLLH_PTP_RULE_MASK 0x187f4
+/* [RW 19] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * TX side. Bits [15:0] reflect the sequence ID of the packet. Bit 16
+ * indicates the validity of the data in the buffer. Bit 17 indicates that
+ * the sequence ID is valid and it is waiting for the TX timestamp value.
+ * Bit 18 indicates whether the timestamp is from a SW request (value of 1)
+ * or HW request (value of 0). Writing a 1 to bit 16 will clear the buffer.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_SEQID 0x187ec
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the lower 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_LSB 0x187e4
+/* [R 32] Packet TimeSync information that is buffered in 1-deep FIFOs for
+ * MCP. This location returns the upper 32 bits of timestamp value.
+ */
+#define NIG_REG_P1_TLLH_PTP_BUF_TS_MSB 0x187e8
+/* [RW 11] Mask register for the various parameters used in determining PTP
+ * packet presence. Set each bit to 1 to mask out the particular parameter.
+ * 0-IPv4 DA 0 of 224.0.1.129. 1-IPv4 DA 1 of 224.0.0.107. 2-IPv6 DA 0 of
+ * 0xFF0*:0:0:0:0:0:0:181. 3-IPv6 DA 1 of 0xFF02:0:0:0:0:0:0:6B. 4-UDP
+ * destination port 0 of 319. 5-UDP destination port 1 of 320. 6-MAC
+ * Ethertype 0 of 0x88F7. 7-configurable MAC Ethertype 1. 8-MAC DA 0 of
+ * 0x01-1B-19-00-00-00. 9-MAC DA 1 of 0x01-80-C2-00-00-0E. 10-configurable
+ * MAC DA 2. The reset default is set to mask out all parameters.
+ */
+#define NIG_REG_P1_TLLH_PTP_PARAM_MASK 0x187f8
+/* [RW 14] Mask regiser for the rules used in detecting PTP packets. Set
+ * each bit to 1 to mask out that particular rule. 0-{IPv4 DA 0; UDP DP 0} .
+ * 1-{IPv4 DA 0; UDP DP 1} . 2-{IPv4 DA 1; UDP DP 0} . 3-{IPv4 DA 1; UDP DP
+ * 1} . 4-{IPv6 DA 0; UDP DP 0} . 5-{IPv6 DA 0; UDP DP 1} . 6-{IPv6 DA 1;
+ * UDP DP 0} . 7-{IPv6 DA 1; UDP DP 1} . 8-{MAC DA 0; Ethertype 0} . 9-{MAC
+ * DA 1; Ethertype 0} . 10-{MAC DA 0; Ethertype 1} . 11-{MAC DA 1; Ethertype
+ * 1} . 12-{MAC DA 2; Ethertype 0} . 13-{MAC DA 2; Ethertype 1} . The reset
+ * default is to mask out all of the rules.
+ */
+#define NIG_REG_P1_TLLH_PTP_RULE_MASK 0x187fc
+/* [RW 32] Specify which of the credit registers the client is to be mapped
+ * to. This register specifies bits 31:0 of the 36-bit value. Bits[3:0] are
+ * for client 0; bits [35:32] are for client 8. For clients that are not
+ * subject to WFQ credit blocking - their specifications here are not used.
+ * This is a new register (with 2_) added in E3 B0 to accommodate the 9
+ * input clients to ETS arbiter. The reset default is set for management and
+ * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to
+ * use credit registers 0-5 respectively (0x543210876). Note that credit
+ * registers can not be shared between clients. Note also that there are
+ * only COS0-2 in port 1- there is a total of 6 clients in port 1. Only
+ * credit registers 0-5 are valid. This register should be configured
+ * appropriately before enabling WFQ. */
+#define NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_LSB 0x186e8
+/* [RW 4] Specify which of the credit registers the client is to be mapped
+ * to. This register specifies bits 35:32 of the 36-bit value. Bits[3:0] are
+ * for client 0; bits [35:32] are for client 8. For clients that are not
+ * subject to WFQ credit blocking - their specifications here are not used.
+ * This is a new register (with 2_) added in E3 B0 to accommodate the 9
+ * input clients to ETS arbiter. The reset default is set for management and
+ * debug to use credit registers 6, 7, and 8, respectively, and COSes 0-5 to
+ * use credit registers 0-5 respectively (0x543210876). Note that credit
+ * registers can not be shared between clients. Note also that there are
+ * only COS0-2 in port 1- there is a total of 6 clients in port 1. Only
+ * credit registers 0-5 are valid. This register should be configured
+ * appropriately before enabling WFQ. */
+#define NIG_REG_P1_TX_ARB_CLIENT_CREDIT_MAP2_MSB 0x186ec
+/* [RW 9] Specify whether the client competes directly in the strict
+ * priority arbiter. The bits are mapped according to client ID (client IDs
+ * are defined in tx_arb_priority_client2): 0-management; 1-debug traffic
+ * from this port; 2-debug traffic from other port; 3-COS0 traffic; 4-COS1
+ * traffic; 5-COS2 traffic; 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic.
+ * Default value is set to enable strict priorities for all clients. */
+#define NIG_REG_P1_TX_ARB_CLIENT_IS_STRICT 0x18234
+/* [RW 9] Specify whether the client is subject to WFQ credit blocking. The
+ * bits are mapped according to client ID (client IDs are defined in
+ * tx_arb_priority_client2): 0-management; 1-debug traffic from this port;
+ * 2-debug traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2
+ * traffic; 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. Default value is
+ * 0 for not using WFQ credit blocking. */
+#define NIG_REG_P1_TX_ARB_CLIENT_IS_SUBJECT2WFQ 0x18238
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_0 0x18258
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_1 0x1825c
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_2 0x18260
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_3 0x18264
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_4 0x18268
+#define NIG_REG_P1_TX_ARB_CREDIT_UPPER_BOUND_5 0x186f4
+/* [RW 32] Specify the weight (in bytes) to be added to credit register 0
+ * when it is time to increment. */
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_0 0x18244
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_1 0x18248
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_2 0x1824c
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_3 0x18250
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_4 0x18254
+#define NIG_REG_P1_TX_ARB_CREDIT_WEIGHT_5 0x186f0
+/* [RW 12] Specify the number of strict priority arbitration slots between
+ two round-robin arbitration slots to avoid starvation. A value of 0 means
+ no strict priority cycles - the strict priority with anti-starvation
+ arbiter becomes a round-robin arbiter. */
+#define NIG_REG_P1_TX_ARB_NUM_STRICT_ARB_SLOTS 0x18240
+/* [RW 32] Specify the client number to be assigned to each priority of the
+ strict priority arbiter. This register specifies bits 31:0 of the 36-bit
+ value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
+ client; bits [35-32] are for priority 8 client. The clients are assigned
+ the following IDs: 0-management; 1-debug traffic from this port; 2-debug
+ traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic;
+ 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is
+ set to 0x345678021. This is a new register (with 2_) added in E3 B0 to
+ accommodate the 9 input clients to ETS arbiter. Note that this register
+ is the same as the one for port 0, except that port 1 only has COS 0-2
+ traffic. There is no traffic for COS 3-5 of port 1. */
+#define NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_LSB 0x186e0
+/* [RW 4] Specify the client number to be assigned to each priority of the
+ strict priority arbiter. This register specifies bits 35:32 of the 36-bit
+ value. Priority 0 is the highest priority. Bits [3:0] are for priority 0
+ client; bits [35-32] are for priority 8 client. The clients are assigned
+ the following IDs: 0-management; 1-debug traffic from this port; 2-debug
+ traffic from other port; 3-COS0 traffic; 4-COS1 traffic; 5-COS2 traffic;
+ 6-COS3 traffic; 7-COS4 traffic; 8-COS5 traffic. The reset value[35:0] is
+ set to 0x345678021. This is a new register (with 2_) added in E3 B0 to
+ accommodate the 9 input clients to ETS arbiter. Note that this register
+ is the same as the one for port 0, except that port 1 only has COS 0-2
+ traffic. There is no traffic for COS 3-5 of port 1. */
+#define NIG_REG_P1_TX_ARB_PRIORITY_CLIENT2_MSB 0x186e4
+/* [R 1] TX FIFO for transmitting data to MAC is empty. */
+#define NIG_REG_P1_TX_MACFIFO_EMPTY 0x18594
+/* [RW 1] MCP-to-host path enable. Set this bit to enable the routing of MCP
+ * packets to BRB LB interface to forward the packet to the host. All
+ * packets from MCP are forwarded to the network when this bit is cleared -
+ * regardless of the configured destination in tx_mng_destination register.
+ */
+#define NIG_REG_P1_TX_MNG_HOST_ENABLE 0x182f8
+/* [R 1] FIFO empty status of the MCP TX FIFO used for storing MCP packets
+ forwarded to the host. */
+#define NIG_REG_P1_TX_MNG_HOST_FIFO_EMPTY 0x182b8
+/* [RW 32] Specify the upper bound that credit register 0 is allowed to
+ * reach. */
+/* [RW 1] Pause enable for port0. This register may get 1 only when
+ ~safc_enable.safc_enable = 0 and ppp_enable.ppp_enable =0 for the same
+ port */
+#define NIG_REG_PAUSE_ENABLE_0 0x160c0
+#define NIG_REG_PAUSE_ENABLE_1 0x160c4
+/* [RW 1] Input enable for RX PBF LP IF */
+#define NIG_REG_PBF_LB_IN_EN 0x100b4
+/* [RW 1] Value of this register will be transmitted to port swap when
+ ~nig_registers_strap_override.strap_override =1 */
+#define NIG_REG_PORT_SWAP 0x10394
+/* [RW 1] PPP enable for port0. This register may get 1 only when
+ * ~safc_enable.safc_enable = 0 and pause_enable.pause_enable =0 for the
+ * same port */
+#define NIG_REG_PPP_ENABLE_0 0x160b0
+#define NIG_REG_PPP_ENABLE_1 0x160b4
+/* [RW 1] output enable for RX parser descriptor IF */
+#define NIG_REG_PRS_EOP_OUT_EN 0x10104
+/* [RW 1] Input enable for RX parser request IF */
+#define NIG_REG_PRS_REQ_IN_EN 0x100b8
+/* [RW 5] control to serdes - CL45 DEVAD */
+#define NIG_REG_SERDES0_CTRL_MD_DEVAD 0x10370
+/* [RW 1] control to serdes; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_SERDES0_CTRL_MD_ST 0x1036c
+/* [RW 5] control to serdes - CL22 PHY_ADD and CL45 PRTAD */
+#define NIG_REG_SERDES0_CTRL_PHY_ADDR 0x10374
+/* [R 1] status from serdes0 that inputs to interrupt logic of link status */
+#define NIG_REG_SERDES0_STATUS_LINK_STATUS 0x10578
+/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
+ for port0 */
+#define NIG_REG_STAT0_BRB_DISCARD 0x105f0
+/* [R 32] Rx statistics : In user packets truncated due to BRB backpressure
+ for port0 */
+#define NIG_REG_STAT0_BRB_TRUNCATE 0x105f8
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1024 and 1522 bytes for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT0 0x10750
+/* [WB_R 36] Tx statistics : Number of packets from emac0 or bmac0 that
+ between 1523 bytes and above for port0 */
+#define NIG_REG_STAT0_EGRESS_MAC_PKT1 0x10760
+/* [R 32] Rx statistics : In user packets discarded due to BRB backpressure
+ for port1 */
+#define NIG_REG_STAT1_BRB_DISCARD 0x10628
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1024 and 1522 bytes for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT0 0x107a0
+/* [WB_R 36] Tx statistics : Number of packets from emac1 or bmac1 that
+ between 1523 bytes and above for port1 */
+#define NIG_REG_STAT1_EGRESS_MAC_PKT1 0x107b0
+/* [WB_R 64] Rx statistics : User octets received for LP */
+#define NIG_REG_STAT2_BRB_OCTET 0x107e0
+#define NIG_REG_STATUS_INTERRUPT_PORT0 0x10328
+#define NIG_REG_STATUS_INTERRUPT_PORT1 0x1032c
+/* [RW 1] port swap mux selection. If this register equal to 0 then port
+ swap is equal to SPIO pin that inputs from ifmux_serdes_swap. If 1 then
+ ort swap is equal to ~nig_registers_port_swap.port_swap */
+#define NIG_REG_STRAP_OVERRIDE 0x10398
+/* [WB 64] Addresses for TimeSync related registers in the timesync
+ * generator sub-module.
+ */
+#define NIG_REG_TIMESYNC_GEN_REG 0x18800
+/* [RW 1] output enable for RX_XCM0 IF */
+#define NIG_REG_XCM0_OUT_EN 0x100f0
+/* [RW 1] output enable for RX_XCM1 IF */
+#define NIG_REG_XCM1_OUT_EN 0x100f4
+/* [RW 1] control to xgxs - remote PHY in-band MDIO */
+#define NIG_REG_XGXS0_CTRL_EXTREMOTEMDIOST 0x10348
+/* [RW 5] control to xgxs - CL45 DEVAD */
+#define NIG_REG_XGXS0_CTRL_MD_DEVAD 0x1033c
+/* [RW 1] control to xgxs; 0 - clause 45; 1 - clause 22 */
+#define NIG_REG_XGXS0_CTRL_MD_ST 0x10338
+/* [RW 5] control to xgxs - CL22 PHY_ADD and CL45 PRTAD */
+#define NIG_REG_XGXS0_CTRL_PHY_ADDR 0x10340
+/* [R 1] status from xgxs0 that inputs to interrupt logic of link10g. */
+#define NIG_REG_XGXS0_STATUS_LINK10G 0x10680
+/* [R 4] status from xgxs0 that inputs to interrupt logic of link status */
+#define NIG_REG_XGXS0_STATUS_LINK_STATUS 0x10684
+/* [RW 2] selection for XGXS lane of port 0 in NIG_MUX block */
+#define NIG_REG_XGXS_LANE_SEL_P0 0x102e8
+/* [RW 1] selection for port0 for NIG_MUX block : 0 = SerDes; 1 = XGXS */
+#define NIG_REG_XGXS_SERDES0_MODE_SEL 0x102e0
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_EMAC0_MISC_MI_INT (0x1<<0)
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_SERDES0_LINK_STATUS (0x1<<9)
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK10G (0x1<<15)
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS (0xf<<18)
+#define NIG_STATUS_INTERRUPT_PORT0_REG_STATUS_XGXS0_LINK_STATUS_SIZE 18
+/* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter. */
+#define PBF_REG_COS0_UPPER_BOUND 0x15c05c
+/* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter
+ * of port 0. */
+#define PBF_REG_COS0_UPPER_BOUND_P0 0x15c2cc
+/* [RW 31] The upper bound of the weight of COS0 in the ETS command arbiter
+ * of port 1. */
+#define PBF_REG_COS0_UPPER_BOUND_P1 0x15c2e4
+/* [RW 31] The weight of COS0 in the ETS command arbiter. */
+#define PBF_REG_COS0_WEIGHT 0x15c054
+/* [RW 31] The weight of COS0 in port 0 ETS command arbiter. */
+#define PBF_REG_COS0_WEIGHT_P0 0x15c2a8
+/* [RW 31] The weight of COS0 in port 1 ETS command arbiter. */
+#define PBF_REG_COS0_WEIGHT_P1 0x15c2c0
+/* [RW 31] The upper bound of the weight of COS1 in the ETS command arbiter. */
+#define PBF_REG_COS1_UPPER_BOUND 0x15c060
+/* [RW 31] The weight of COS1 in the ETS command arbiter. */
+#define PBF_REG_COS1_WEIGHT 0x15c058
+/* [RW 31] The weight of COS1 in port 0 ETS command arbiter. */
+#define PBF_REG_COS1_WEIGHT_P0 0x15c2ac
+/* [RW 31] The weight of COS1 in port 1 ETS command arbiter. */
+#define PBF_REG_COS1_WEIGHT_P1 0x15c2c4
+/* [RW 31] The weight of COS2 in port 0 ETS command arbiter. */
+#define PBF_REG_COS2_WEIGHT_P0 0x15c2b0
+/* [RW 31] The weight of COS2 in port 1 ETS command arbiter. */
+#define PBF_REG_COS2_WEIGHT_P1 0x15c2c8
+/* [RW 31] The weight of COS3 in port 0 ETS command arbiter. */
+#define PBF_REG_COS3_WEIGHT_P0 0x15c2b4
+/* [RW 31] The weight of COS4 in port 0 ETS command arbiter. */
+#define PBF_REG_COS4_WEIGHT_P0 0x15c2b8
+/* [RW 31] The weight of COS5 in port 0 ETS command arbiter. */
+#define PBF_REG_COS5_WEIGHT_P0 0x15c2bc
+/* [R 11] Current credit for the LB queue in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_CREDIT_LB_Q 0x140338
+/* [R 11] Current credit for queue 0 in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_CREDIT_Q0 0x14033c
+/* [R 11] Current credit for queue 1 in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_CREDIT_Q1 0x140340
+/* [RW 1] Disable processing further tasks from port 0 (after ending the
+ current task in process). */
+#define PBF_REG_DISABLE_NEW_TASK_PROC_P0 0x14005c
+/* [RW 1] Disable processing further tasks from port 1 (after ending the
+ current task in process). */
+#define PBF_REG_DISABLE_NEW_TASK_PROC_P1 0x140060
+/* [RW 1] Disable processing further tasks from port 4 (after ending the
+ current task in process). */
+#define PBF_REG_DISABLE_NEW_TASK_PROC_P4 0x14006c
+#define PBF_REG_DISABLE_PF 0x1402e8
+#define PBF_REG_DISABLE_VF 0x1402ec
+/* [RW 18] For port 0: For each client that is subject to WFQ (the
+ * corresponding bit is 1); indicates to which of the credit registers this
+ * client is mapped. For clients which are not credit blocked; their mapping
+ * is dont care. */
+#define PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P0 0x15c288
+/* [RW 9] For port 1: For each client that is subject to WFQ (the
+ * corresponding bit is 1); indicates to which of the credit registers this
+ * client is mapped. For clients which are not credit blocked; their mapping
+ * is dont care. */
+#define PBF_REG_ETS_ARB_CLIENT_CREDIT_MAP_P1 0x15c28c
+/* [RW 6] For port 0: Bit per client to indicate if the client competes in
+ * the strict priority arbiter directly (corresponding bit = 1); or first
+ * goes to the RR arbiter (corresponding bit = 0); and then competes in the
+ * lowest priority in the strict-priority arbiter. */
+#define PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P0 0x15c278
+/* [RW 3] For port 1: Bit per client to indicate if the client competes in
+ * the strict priority arbiter directly (corresponding bit = 1); or first
+ * goes to the RR arbiter (corresponding bit = 0); and then competes in the
+ * lowest priority in the strict-priority arbiter. */
+#define PBF_REG_ETS_ARB_CLIENT_IS_STRICT_P1 0x15c27c
+/* [RW 6] For port 0: Bit per client to indicate if the client is subject to
+ * WFQ credit blocking (corresponding bit = 1). */
+#define PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P0 0x15c280
+/* [RW 3] For port 0: Bit per client to indicate if the client is subject to
+ * WFQ credit blocking (corresponding bit = 1). */
+#define PBF_REG_ETS_ARB_CLIENT_IS_SUBJECT2WFQ_P1 0x15c284
+/* [RW 16] For port 0: The number of strict priority arbitration slots
+ * between 2 RR arbitration slots. A value of 0 means no strict priority
+ * cycles; i.e. the strict-priority w/ anti-starvation arbiter is a RR
+ * arbiter. */
+#define PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P0 0x15c2a0
+/* [RW 16] For port 1: The number of strict priority arbitration slots
+ * between 2 RR arbitration slots. A value of 0 means no strict priority
+ * cycles; i.e. the strict-priority w/ anti-starvation arbiter is a RR
+ * arbiter. */
+#define PBF_REG_ETS_ARB_NUM_STRICT_ARB_SLOTS_P1 0x15c2a4
+/* [RW 18] For port 0: Indicates which client is connected to each priority
+ * in the strict-priority arbiter. Priority 0 is the highest priority, and
+ * priority 5 is the lowest; to which the RR output is connected to (this is
+ * not configurable). */
+#define PBF_REG_ETS_ARB_PRIORITY_CLIENT_P0 0x15c270
+/* [RW 9] For port 1: Indicates which client is connected to each priority
+ * in the strict-priority arbiter. Priority 0 is the highest priority, and
+ * priority 5 is the lowest; to which the RR output is connected to (this is
+ * not configurable). */
+#define PBF_REG_ETS_ARB_PRIORITY_CLIENT_P1 0x15c274
+/* [RW 1] Indicates that ETS is performed between the COSes in the command
+ * arbiter. If reset strict priority w/ anti-starvation will be performed
+ * w/o WFQ. */
+#define PBF_REG_ETS_ENABLED 0x15c050
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
+ * Ethernet header. */
+#define PBF_REG_HDRS_AFTER_BASIC 0x15c0a8
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 */
+#define PBF_REG_HDRS_AFTER_TAG_0 0x15c0b8
+/* [R 1] Removed for E3 B0 - Indicates which COS is conncted to the highest
+ * priority in the command arbiter. */
+#define PBF_REG_HIGH_PRIORITY_COS_NUM 0x15c04c
+#define PBF_REG_IF_ENABLE_REG 0x140044
+/* [RW 1] Init bit. When set the initial credits are copied to the credit
+ registers (except the port credits). Should be set and then reset after
+ the configuration of the block has ended. */
+#define PBF_REG_INIT 0x140000
+/* [RW 11] Initial credit for the LB queue in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_INIT_CRD_LB_Q 0x15c248
+/* [RW 11] Initial credit for queue 0 in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_INIT_CRD_Q0 0x15c230
+/* [RW 11] Initial credit for queue 1 in the tx port buffers in 16 byte
+ * lines. */
+#define PBF_REG_INIT_CRD_Q1 0x15c234
+/* [RW 1] Init bit for port 0. When set the initial credit of port 0 is
+ copied to the credit register. Should be set and then reset after the
+ configuration of the port has ended. */
+#define PBF_REG_INIT_P0 0x140004
+/* [RW 1] Init bit for port 1. When set the initial credit of port 1 is
+ copied to the credit register. Should be set and then reset after the
+ configuration of the port has ended. */
+#define PBF_REG_INIT_P1 0x140008
+/* [RW 1] Init bit for port 4. When set the initial credit of port 4 is
+ copied to the credit register. Should be set and then reset after the
+ configuration of the port has ended. */
+#define PBF_REG_INIT_P4 0x14000c
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * the LB queue. Reset upon init. */
+#define PBF_REG_INTERNAL_CRD_FREED_CNT_LB_Q 0x140354
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * queue 0. Reset upon init. */
+#define PBF_REG_INTERNAL_CRD_FREED_CNT_Q0 0x140358
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * queue 1. Reset upon init. */
+#define PBF_REG_INTERNAL_CRD_FREED_CNT_Q1 0x14035c
+/* [RW 1] Enable for mac interface 0. */
+#define PBF_REG_MAC_IF0_ENABLE 0x140030
+/* [RW 1] Enable for mac interface 1. */
+#define PBF_REG_MAC_IF1_ENABLE 0x140034
+/* [RW 1] Enable for the loopback interface. */
+#define PBF_REG_MAC_LB_ENABLE 0x140040
+/* [RW 6] Bit-map indicating which headers must appear in the packet */
+#define PBF_REG_MUST_HAVE_HDRS 0x15c0c4
+/* [RW 16] The number of strict priority arbitration slots between 2 RR
+ * arbitration slots. A value of 0 means no strict priority cycles; i.e. the
+ * strict-priority w/ anti-starvation arbiter is a RR arbiter. */
+#define PBF_REG_NUM_STRICT_ARB_SLOTS 0x15c064
+/* [RW 10] Port 0 threshold used by arbiter in 16 byte lines used when pause
+ not suppoterd. */
+#define PBF_REG_P0_ARB_THRSH 0x1400e4
+/* [R 11] Current credit for port 0 in the tx port buffers in 16 byte lines. */
+#define PBF_REG_P0_CREDIT 0x140200
+/* [RW 11] Initial credit for port 0 in the tx port buffers in 16 byte
+ lines. */
+#define PBF_REG_P0_INIT_CRD 0x1400d0
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * port 0. Reset upon init. */
+#define PBF_REG_P0_INTERNAL_CRD_FREED_CNT 0x140308
+/* [R 1] Removed for E3 B0 - Indication that pause is enabled for port 0. */
+#define PBF_REG_P0_PAUSE_ENABLE 0x140014
+/* [R 8] Removed for E3 B0 - Number of tasks in port 0 task queue. */
+#define PBF_REG_P0_TASK_CNT 0x140204
+/* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines
+ * freed from the task queue of port 0. Reset upon init. */
+#define PBF_REG_P0_TQ_LINES_FREED_CNT 0x1402f0
+/* [R 12] Number of 8 bytes lines occupied in the task queue of port 0. */
+#define PBF_REG_P0_TQ_OCCUPANCY 0x1402fc
+/* [R 11] Removed for E3 B0 - Current credit for port 1 in the tx port
+ * buffers in 16 byte lines. */
+#define PBF_REG_P1_CREDIT 0x140208
+/* [R 11] Removed for E3 B0 - Initial credit for port 0 in the tx port
+ * buffers in 16 byte lines. */
+#define PBF_REG_P1_INIT_CRD 0x1400d4
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * port 1. Reset upon init. */
+#define PBF_REG_P1_INTERNAL_CRD_FREED_CNT 0x14030c
+/* [R 8] Removed for E3 B0 - Number of tasks in port 1 task queue. */
+#define PBF_REG_P1_TASK_CNT 0x14020c
+/* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines
+ * freed from the task queue of port 1. Reset upon init. */
+#define PBF_REG_P1_TQ_LINES_FREED_CNT 0x1402f4
+/* [R 12] Number of 8 bytes lines occupied in the task queue of port 1. */
+#define PBF_REG_P1_TQ_OCCUPANCY 0x140300
+/* [R 11] Current credit for port 4 in the tx port buffers in 16 byte lines. */
+#define PBF_REG_P4_CREDIT 0x140210
+/* [RW 11] Initial credit for port 4 in the tx port buffers in 16 byte
+ lines. */
+#define PBF_REG_P4_INIT_CRD 0x1400e0
+/* [R 32] Cyclic counter for the amount credits in 16 bytes lines added for
+ * port 4. Reset upon init. */
+#define PBF_REG_P4_INTERNAL_CRD_FREED_CNT 0x140310
+/* [R 8] Removed for E3 B0 - Number of tasks in port 4 task queue. */
+#define PBF_REG_P4_TASK_CNT 0x140214
+/* [R 32] Removed for E3 B0 - Cyclic counter for number of 8 byte lines
+ * freed from the task queue of port 4. Reset upon init. */
+#define PBF_REG_P4_TQ_LINES_FREED_CNT 0x1402f8
+/* [R 12] Number of 8 bytes lines occupied in the task queue of port 4. */
+#define PBF_REG_P4_TQ_OCCUPANCY 0x140304
+/* [RW 5] Interrupt mask register #0 read/write */
+#define PBF_REG_PBF_INT_MASK 0x1401d4
+/* [R 5] Interrupt register #0 read */
+#define PBF_REG_PBF_INT_STS 0x1401c8
+/* [RW 20] Parity mask register #0 read/write */
+#define PBF_REG_PBF_PRTY_MASK 0x1401e4
+/* [R 28] Parity register #0 read */
+#define PBF_REG_PBF_PRTY_STS 0x1401d8
+/* [RC 20] Parity register #0 read clear */
+#define PBF_REG_PBF_PRTY_STS_CLR 0x1401dc
+/* [RW 16] The Ethernet type value for L2 tag 0 */
+#define PBF_REG_TAG_ETHERTYPE_0 0x15c090
+/* [RW 4] The length of the info field for L2 tag 0. The length is between
+ * 2B and 14B; in 2B granularity */
+#define PBF_REG_TAG_LEN_0 0x15c09c
+/* [R 32] Cyclic counter for number of 8 byte lines freed from the LB task
+ * queue. Reset upon init. */
+#define PBF_REG_TQ_LINES_FREED_CNT_LB_Q 0x14038c
+/* [R 32] Cyclic counter for number of 8 byte lines freed from the task
+ * queue 0. Reset upon init. */
+#define PBF_REG_TQ_LINES_FREED_CNT_Q0 0x140390
+/* [R 32] Cyclic counter for number of 8 byte lines freed from task queue 1.
+ * Reset upon init. */
+#define PBF_REG_TQ_LINES_FREED_CNT_Q1 0x140394
+/* [R 13] Number of 8 bytes lines occupied in the task queue of the LB
+ * queue. */
+#define PBF_REG_TQ_OCCUPANCY_LB_Q 0x1403a8
+/* [R 13] Number of 8 bytes lines occupied in the task queue of queue 0. */
+#define PBF_REG_TQ_OCCUPANCY_Q0 0x1403ac
+/* [R 13] Number of 8 bytes lines occupied in the task queue of queue 1. */
+#define PBF_REG_TQ_OCCUPANCY_Q1 0x1403b0
+#define PB_REG_CONTROL 0
+/* [RW 2] Interrupt mask register #0 read/write */
+#define PB_REG_PB_INT_MASK 0x28
+/* [R 2] Interrupt register #0 read */
+#define PB_REG_PB_INT_STS 0x1c
+/* [RW 4] Parity mask register #0 read/write */
+#define PB_REG_PB_PRTY_MASK 0x38
+/* [R 4] Parity register #0 read */
+#define PB_REG_PB_PRTY_STS 0x2c
+/* [RC 4] Parity register #0 read clear */
+#define PB_REG_PB_PRTY_STS_CLR 0x30
+#define PGLUE_B_PGLUE_B_INT_STS_REG_ADDRESS_ERROR (0x1<<0)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_CSSNOOP_FIFO_OVERFLOW (0x1<<8)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_INCORRECT_RCV_BEHAVIOR (0x1<<1)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_TCPL_ERROR_ATTN (0x1<<6)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_TCPL_IN_TWO_RCBS_ATTN (0x1<<7)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_VF_GRC_SPACE_VIOLATION_ATTN (0x1<<4)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_VF_LENGTH_VIOLATION_ATTN (0x1<<3)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_VF_MSIX_BAR_VIOLATION_ATTN (0x1<<5)
+#define PGLUE_B_PGLUE_B_INT_STS_REG_WAS_ERROR_ATTN (0x1<<2)
+/* [R 8] Config space A attention dirty bits. Each bit indicates that the
+ * corresponding PF generates config space A attention. Set by PXP. Reset by
+ * MCP writing 1 to icfg_space_a_request_clr. Note: register contains bits
+ * from both paths. */
+#define PGLUE_B_REG_CFG_SPACE_A_REQUEST 0x9010
+/* [R 8] Config space B attention dirty bits. Each bit indicates that the
+ * corresponding PF generates config space B attention. Set by PXP. Reset by
+ * MCP writing 1 to icfg_space_b_request_clr. Note: register contains bits
+ * from both paths. */
+#define PGLUE_B_REG_CFG_SPACE_B_REQUEST 0x9014
+/* [RW 1] Type A PF enable inbound interrupt table for CSDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_CSDM_INB_INT_A_PF_ENABLE 0x9194
+/* [RW 18] Type B VF inbound interrupt table for CSDM: bits[17:9]-mask;
+ * its[8:0]-address. Bits [1:0] must be zero (DW resolution address). */
+#define PGLUE_B_REG_CSDM_INB_INT_B_VF 0x916c
+/* [RW 1] Type B VF enable inbound interrupt table for CSDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_CSDM_INB_INT_B_VF_ENABLE 0x919c
+/* [RW 16] Start offset of CSDM zone A (queue zone) in the internal RAM */
+#define PGLUE_B_REG_CSDM_START_OFFSET_A 0x9100
+/* [RW 16] Start offset of CSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_CSDM_START_OFFSET_B 0x9108
+/* [RW 5] VF Shift of CSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_CSDM_VF_SHIFT_B 0x9110
+/* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */
+#define PGLUE_B_REG_CSDM_ZONE_A_SIZE_PF 0x91ac
+/* [R 8] FLR request attention dirty bits for PFs 0 to 7. Each bit indicates
+ * that the FLR register of the corresponding PF was set. Set by PXP. Reset
+ * by MCP writing 1 to flr_request_pf_7_0_clr. Note: register contains bits
+ * from both paths. */
+#define PGLUE_B_REG_FLR_REQUEST_PF_7_0 0x9028
+/* [W 8] FLR request attention dirty bits clear for PFs 0 to 7. MCP writes 1
+ * to a bit in this register in order to clear the corresponding bit in
+ * flr_request_pf_7_0 register. Note: register contains bits from both
+ * paths. */
+#define PGLUE_B_REG_FLR_REQUEST_PF_7_0_CLR 0x9418
+/* [R 32] FLR request attention dirty bits for VFs 96 to 127. Each bit
+ * indicates that the FLR register of the corresponding VF was set. Set by
+ * PXP. Reset by MCP writing 1 to flr_request_vf_127_96_clr. */
+#define PGLUE_B_REG_FLR_REQUEST_VF_127_96 0x9024
+/* [R 32] FLR request attention dirty bits for VFs 0 to 31. Each bit
+ * indicates that the FLR register of the corresponding VF was set. Set by
+ * PXP. Reset by MCP writing 1 to flr_request_vf_31_0_clr. */
+#define PGLUE_B_REG_FLR_REQUEST_VF_31_0 0x9018
+/* [R 32] FLR request attention dirty bits for VFs 32 to 63. Each bit
+ * indicates that the FLR register of the corresponding VF was set. Set by
+ * PXP. Reset by MCP writing 1 to flr_request_vf_63_32_clr. */
+#define PGLUE_B_REG_FLR_REQUEST_VF_63_32 0x901c
+/* [R 32] FLR request attention dirty bits for VFs 64 to 95. Each bit
+ * indicates that the FLR register of the corresponding VF was set. Set by
+ * PXP. Reset by MCP writing 1 to flr_request_vf_95_64_clr. */
+#define PGLUE_B_REG_FLR_REQUEST_VF_95_64 0x9020
+/* [R 8] Each bit indicates an incorrect behavior in user RX interface. Bit
+ * 0 - Target memory read arrived with a correctable error. Bit 1 - Target
+ * memory read arrived with an uncorrectable error. Bit 2 - Configuration RW
+ * arrived with a correctable error. Bit 3 - Configuration RW arrived with
+ * an uncorrectable error. Bit 4 - Completion with Configuration Request
+ * Retry Status. Bit 5 - Expansion ROM access received with a write request.
+ * Bit 6 - Completion with pcie_rx_err of 0000; CMPL_STATUS of non-zero; and
+ * pcie_rx_last not asserted. Bit 7 - Completion with pcie_rx_err of 1010;
+ * and pcie_rx_last not asserted. */
+#define PGLUE_B_REG_INCORRECT_RCV_DETAILS 0x9068
+#define PGLUE_B_REG_INTERNAL_PFID_ENABLE_MASTER 0x942c
+#define PGLUE_B_REG_INTERNAL_PFID_ENABLE_TARGET_READ 0x9430
+#define PGLUE_B_REG_INTERNAL_PFID_ENABLE_TARGET_WRITE 0x9434
+#define PGLUE_B_REG_INTERNAL_VFID_ENABLE 0x9438
+/* [W 7] Writing 1 to each bit in this register clears a corresponding error
+ * details register and enables logging new error details. Bit 0 - clears
+ * INCORRECT_RCV_DETAILS; Bit 1 - clears RX_ERR_DETAILS; Bit 2 - clears
+ * TX_ERR_WR_ADD_31_0 TX_ERR_WR_ADD_63_32 TX_ERR_WR_DETAILS
+ * TX_ERR_WR_DETAILS2 TX_ERR_RD_ADD_31_0 TX_ERR_RD_ADD_63_32
+ * TX_ERR_RD_DETAILS TX_ERR_RD_DETAILS2 TX_ERR_WR_DETAILS_ICPL; Bit 3 -
+ * clears VF_LENGTH_VIOLATION_DETAILS. Bit 4 - clears
+ * VF_GRC_SPACE_VIOLATION_DETAILS. Bit 5 - clears RX_TCPL_ERR_DETAILS. Bit 6
+ * - clears TCPL_IN_TWO_RCBS_DETAILS. */
+#define PGLUE_B_REG_LATCHED_ERRORS_CLR 0x943c
+
+/* [R 9] Interrupt register #0 read */
+#define PGLUE_B_REG_PGLUE_B_INT_STS 0x9298
+/* [RC 9] Interrupt register #0 read clear */
+#define PGLUE_B_REG_PGLUE_B_INT_STS_CLR 0x929c
+/* [RW 2] Parity mask register #0 read/write */
+#define PGLUE_B_REG_PGLUE_B_PRTY_MASK 0x92b4
+/* [R 2] Parity register #0 read */
+#define PGLUE_B_REG_PGLUE_B_PRTY_STS 0x92a8
+/* [RC 2] Parity register #0 read clear */
+#define PGLUE_B_REG_PGLUE_B_PRTY_STS_CLR 0x92ac
+/* [R 13] Details of first request received with error. [2:0] - PFID. [3] -
+ * VF_VALID. [9:4] - VFID. [11:10] - Error Code - 0 - Indicates Completion
+ * Timeout of a User Tx non-posted request. 1 - unsupported request. 2 -
+ * completer abort. 3 - Illegal value for this field. [12] valid - indicates
+ * if there was a completion error since the last time this register was
+ * cleared. */
+#define PGLUE_B_REG_RX_ERR_DETAILS 0x9080
+/* [R 18] Details of first ATS Translation Completion request received with
+ * error. [2:0] - PFID. [3] - VF_VALID. [9:4] - VFID. [11:10] - Error Code -
+ * 0 - Indicates Completion Timeout of a User Tx non-posted request. 1 -
+ * unsupported request. 2 - completer abort. 3 - Illegal value for this
+ * field. [16:12] - ATC OTB EntryID. [17] valid - indicates if there was a
+ * completion error since the last time this register was cleared. */
+#define PGLUE_B_REG_RX_TCPL_ERR_DETAILS 0x9084
+/* [W 8] Debug only - Shadow BME bits clear for PFs 0 to 7. MCP writes 1 to
+ * a bit in this register in order to clear the corresponding bit in
+ * shadow_bme_pf_7_0 register. MCP should never use this unless a
+ * work-around is needed. Note: register contains bits from both paths. */
+#define PGLUE_B_REG_SHADOW_BME_PF_7_0_CLR 0x9458
+/* [R 8] SR IOV disabled attention dirty bits. Each bit indicates that the
+ * VF enable register of the corresponding PF is written to 0 and was
+ * previously 1. Set by PXP. Reset by MCP writing 1 to
+ * sr_iov_disabled_request_clr. Note: register contains bits from both
+ * paths. */
+#define PGLUE_B_REG_SR_IOV_DISABLED_REQUEST 0x9030
+/* [R 32] Indicates the status of tags 32-63. 0 - tags is used - read
+ * completion did not return yet. 1 - tag is unused. Same functionality as
+ * pxp2_registers_pgl_exp_rom_data2 for tags 0-31. */
+#define PGLUE_B_REG_TAGS_63_32 0x9244
+/* [RW 1] Type A PF enable inbound interrupt table for TSDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_TSDM_INB_INT_A_PF_ENABLE 0x9170
+/* [RW 16] Start offset of TSDM zone A (queue zone) in the internal RAM */
+#define PGLUE_B_REG_TSDM_START_OFFSET_A 0x90c4
+/* [RW 16] Start offset of TSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_TSDM_START_OFFSET_B 0x90cc
+/* [RW 5] VF Shift of TSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_TSDM_VF_SHIFT_B 0x90d4
+/* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */
+#define PGLUE_B_REG_TSDM_ZONE_A_SIZE_PF 0x91a0
+/* [R 32] Address [31:0] of first read request not submitted due to error */
+#define PGLUE_B_REG_TX_ERR_RD_ADD_31_0 0x9098
+/* [R 32] Address [63:32] of first read request not submitted due to error */
+#define PGLUE_B_REG_TX_ERR_RD_ADD_63_32 0x909c
+/* [R 31] Details of first read request not submitted due to error. [4:0]
+ * VQID. [5] TREQ. 1 - Indicates the request is a Translation Request.
+ * [20:8] - Length in bytes. [23:21] - PFID. [24] - VF_VALID. [30:25] -
+ * VFID. */
+#define PGLUE_B_REG_TX_ERR_RD_DETAILS 0x90a0
+/* [R 26] Details of first read request not submitted due to error. [15:0]
+ * Request ID. [19:16] client ID. [20] - last SR. [24:21] - Error type -
+ * [21] - Indicates was_error was set; [22] - Indicates BME was cleared;
+ * [23] - Indicates FID_enable was cleared; [24] - Indicates VF with parent
+ * PF FLR_request or IOV_disable_request dirty bit is set. [25] valid -
+ * indicates if there was a request not submitted due to error since the
+ * last time this register was cleared. */
+#define PGLUE_B_REG_TX_ERR_RD_DETAILS2 0x90a4
+/* [R 32] Address [31:0] of first write request not submitted due to error */
+#define PGLUE_B_REG_TX_ERR_WR_ADD_31_0 0x9088
+/* [R 32] Address [63:32] of first write request not submitted due to error */
+#define PGLUE_B_REG_TX_ERR_WR_ADD_63_32 0x908c
+/* [R 31] Details of first write request not submitted due to error. [4:0]
+ * VQID. [20:8] - Length in bytes. [23:21] - PFID. [24] - VF_VALID. [30:25]
+ * - VFID. */
+#define PGLUE_B_REG_TX_ERR_WR_DETAILS 0x9090
+/* [R 26] Details of first write request not submitted due to error. [15:0]
+ * Request ID. [19:16] client ID. [20] - last SR. [24:21] - Error type -
+ * [21] - Indicates was_error was set; [22] - Indicates BME was cleared;
+ * [23] - Indicates FID_enable was cleared; [24] - Indicates VF with parent
+ * PF FLR_request or IOV_disable_request dirty bit is set. [25] valid -
+ * indicates if there was a request not submitted due to error since the
+ * last time this register was cleared. */
+#define PGLUE_B_REG_TX_ERR_WR_DETAILS2 0x9094
+/* [RW 10] Type A PF/VF inbound interrupt table for USDM: bits[9:5]-mask;
+ * its[4:0]-address relative to start_offset_a. Bits [1:0] can have any
+ * value (Byte resolution address). */
+#define PGLUE_B_REG_USDM_INB_INT_A_0 0x9128
+#define PGLUE_B_REG_USDM_INB_INT_A_1 0x912c
+#define PGLUE_B_REG_USDM_INB_INT_A_2 0x9130
+#define PGLUE_B_REG_USDM_INB_INT_A_3 0x9134
+#define PGLUE_B_REG_USDM_INB_INT_A_4 0x9138
+#define PGLUE_B_REG_USDM_INB_INT_A_5 0x913c
+#define PGLUE_B_REG_USDM_INB_INT_A_6 0x9140
+/* [RW 1] Type A PF enable inbound interrupt table for USDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_USDM_INB_INT_A_PF_ENABLE 0x917c
+/* [RW 1] Type A VF enable inbound interrupt table for USDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_USDM_INB_INT_A_VF_ENABLE 0x9180
+/* [RW 1] Type B VF enable inbound interrupt table for USDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_USDM_INB_INT_B_VF_ENABLE 0x9184
+/* [RW 16] Start offset of USDM zone A (queue zone) in the internal RAM */
+#define PGLUE_B_REG_USDM_START_OFFSET_A 0x90d8
+/* [RW 16] Start offset of USDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_USDM_START_OFFSET_B 0x90e0
+/* [RW 5] VF Shift of USDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_USDM_VF_SHIFT_B 0x90e8
+/* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */
+#define PGLUE_B_REG_USDM_ZONE_A_SIZE_PF 0x91a4
+/* [R 26] Details of first target VF request accessing VF GRC space that
+ * failed permission check. [14:0] Address. [15] w_nr: 0 - Read; 1 - Write.
+ * [21:16] VFID. [24:22] - PFID. [25] valid - indicates if there was a
+ * request accessing VF GRC space that failed permission check since the
+ * last time this register was cleared. Permission checks are: function
+ * permission; R/W permission; address range permission. */
+#define PGLUE_B_REG_VF_GRC_SPACE_VIOLATION_DETAILS 0x9234
+/* [R 31] Details of first target VF request with length violation (too many
+ * DWs) accessing BAR0. [12:0] Address in DWs (bits [14:2] of byte address).
+ * [14:13] BAR. [20:15] VFID. [23:21] - PFID. [29:24] - Length in DWs. [30]
+ * valid - indicates if there was a request with length violation since the
+ * last time this register was cleared. Length violations: length of more
+ * than 2DWs; length of 2DWs and address not QW aligned; window is GRC and
+ * length is more than 1 DW. */
+#define PGLUE_B_REG_VF_LENGTH_VIOLATION_DETAILS 0x9230
+/* [R 8] Was_error indication dirty bits for PFs 0 to 7. Each bit indicates
+ * that there was a completion with uncorrectable error for the
+ * corresponding PF. Set by PXP. Reset by MCP writing 1 to
+ * was_error_pf_7_0_clr. */
+#define PGLUE_B_REG_WAS_ERROR_PF_7_0 0x907c
+/* [W 8] Was_error indication dirty bits clear for PFs 0 to 7. MCP writes 1
+ * to a bit in this register in order to clear the corresponding bit in
+ * flr_request_pf_7_0 register. */
+#define PGLUE_B_REG_WAS_ERROR_PF_7_0_CLR 0x9470
+/* [R 32] Was_error indication dirty bits for VFs 96 to 127. Each bit
+ * indicates that there was a completion with uncorrectable error for the
+ * corresponding VF. Set by PXP. Reset by MCP writing 1 to
+ * was_error_vf_127_96_clr. */
+#define PGLUE_B_REG_WAS_ERROR_VF_127_96 0x9078
+/* [W 32] Was_error indication dirty bits clear for VFs 96 to 127. MCP
+ * writes 1 to a bit in this register in order to clear the corresponding
+ * bit in was_error_vf_127_96 register. */
+#define PGLUE_B_REG_WAS_ERROR_VF_127_96_CLR 0x9474
+/* [R 32] Was_error indication dirty bits for VFs 0 to 31. Each bit
+ * indicates that there was a completion with uncorrectable error for the
+ * corresponding VF. Set by PXP. Reset by MCP writing 1 to
+ * was_error_vf_31_0_clr. */
+#define PGLUE_B_REG_WAS_ERROR_VF_31_0 0x906c
+/* [W 32] Was_error indication dirty bits clear for VFs 0 to 31. MCP writes
+ * 1 to a bit in this register in order to clear the corresponding bit in
+ * was_error_vf_31_0 register. */
+#define PGLUE_B_REG_WAS_ERROR_VF_31_0_CLR 0x9478
+/* [R 32] Was_error indication dirty bits for VFs 32 to 63. Each bit
+ * indicates that there was a completion with uncorrectable error for the
+ * corresponding VF. Set by PXP. Reset by MCP writing 1 to
+ * was_error_vf_63_32_clr. */
+#define PGLUE_B_REG_WAS_ERROR_VF_63_32 0x9070
+/* [W 32] Was_error indication dirty bits clear for VFs 32 to 63. MCP writes
+ * 1 to a bit in this register in order to clear the corresponding bit in
+ * was_error_vf_63_32 register. */
+#define PGLUE_B_REG_WAS_ERROR_VF_63_32_CLR 0x947c
+/* [R 32] Was_error indication dirty bits for VFs 64 to 95. Each bit
+ * indicates that there was a completion with uncorrectable error for the
+ * corresponding VF. Set by PXP. Reset by MCP writing 1 to
+ * was_error_vf_95_64_clr. */
+#define PGLUE_B_REG_WAS_ERROR_VF_95_64 0x9074
+/* [W 32] Was_error indication dirty bits clear for VFs 64 to 95. MCP writes
+ * 1 to a bit in this register in order to clear the corresponding bit in
+ * was_error_vf_95_64 register. */
+#define PGLUE_B_REG_WAS_ERROR_VF_95_64_CLR 0x9480
+/* [RW 1] Type A PF enable inbound interrupt table for XSDM. 0 - disable; 1
+ * - enable. */
+#define PGLUE_B_REG_XSDM_INB_INT_A_PF_ENABLE 0x9188
+/* [RW 16] Start offset of XSDM zone A (queue zone) in the internal RAM */
+#define PGLUE_B_REG_XSDM_START_OFFSET_A 0x90ec
+/* [RW 16] Start offset of XSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_XSDM_START_OFFSET_B 0x90f4
+/* [RW 5] VF Shift of XSDM zone B (legacy zone) in the internal RAM */
+#define PGLUE_B_REG_XSDM_VF_SHIFT_B 0x90fc
+/* [RW 1] 0 - Zone A size is 136x32B; 1 - Zone A size is 152x32B. */
+#define PGLUE_B_REG_XSDM_ZONE_A_SIZE_PF 0x91a8
+#define PRS_REG_A_PRSU_20 0x40134
+/* [R 8] debug only: CFC load request current credit. Transaction based. */
+#define PRS_REG_CFC_LD_CURRENT_CREDIT 0x40164
+/* [R 8] debug only: CFC search request current credit. Transaction based. */
+#define PRS_REG_CFC_SEARCH_CURRENT_CREDIT 0x40168
+/* [RW 6] The initial credit for the search message to the CFC interface.
+ Credit is transaction based. */
+#define PRS_REG_CFC_SEARCH_INITIAL_CREDIT 0x4011c
+/* [RW 24] CID for port 0 if no match */
+#define PRS_REG_CID_PORT_0 0x400fc
+/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
+ load response is reset and packet type is 0. Used in packet start message
+ to TCM. */
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_0 0x400dc
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_1 0x400e0
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_2 0x400e4
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_3 0x400e8
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_4 0x400ec
+#define PRS_REG_CM_HDR_FLUSH_LOAD_TYPE_5 0x400f0
+/* [RW 32] The CM header for flush message where 'load existed' bit in CFC
+ load response is set and packet type is 0. Used in packet start message
+ to TCM. */
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_0 0x400bc
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_1 0x400c0
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_2 0x400c4
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_3 0x400c8
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_4 0x400cc
+#define PRS_REG_CM_HDR_FLUSH_NO_LOAD_TYPE_5 0x400d0
+/* [RW 32] The CM header for a match and packet type 1 for loopback port.
+ Used in packet start message to TCM. */
+#define PRS_REG_CM_HDR_LOOPBACK_TYPE_1 0x4009c
+#define PRS_REG_CM_HDR_LOOPBACK_TYPE_2 0x400a0
+#define PRS_REG_CM_HDR_LOOPBACK_TYPE_3 0x400a4
+#define PRS_REG_CM_HDR_LOOPBACK_TYPE_4 0x400a8
+/* [RW 32] The CM header for a match and packet type 0. Used in packet start
+ message to TCM. */
+#define PRS_REG_CM_HDR_TYPE_0 0x40078
+#define PRS_REG_CM_HDR_TYPE_1 0x4007c
+#define PRS_REG_CM_HDR_TYPE_2 0x40080
+#define PRS_REG_CM_HDR_TYPE_3 0x40084
+#define PRS_REG_CM_HDR_TYPE_4 0x40088
+/* [RW 32] The CM header in case there was not a match on the connection */
+#define PRS_REG_CM_NO_MATCH_HDR 0x400b8
+/* [RW 1] Indicates if in e1hov mode. 0=non-e1hov mode; 1=e1hov mode. */
+#define PRS_REG_E1HOV_MODE 0x401c8
+/* [RW 8] The 8-bit event ID for a match and packet type 1. Used in packet
+ start message to TCM. */
+#define PRS_REG_EVENT_ID_1 0x40054
+#define PRS_REG_EVENT_ID_2 0x40058
+#define PRS_REG_EVENT_ID_3 0x4005c
+/* [RW 16] The Ethernet type value for FCoE */
+#define PRS_REG_FCOE_TYPE 0x401d0
+/* [RW 8] Context region for flush packet with packet type 0. Used in CFC
+ load request message. */
+#define PRS_REG_FLUSH_REGIONS_TYPE_0 0x40004
+#define PRS_REG_FLUSH_REGIONS_TYPE_1 0x40008
+#define PRS_REG_FLUSH_REGIONS_TYPE_2 0x4000c
+#define PRS_REG_FLUSH_REGIONS_TYPE_3 0x40010
+#define PRS_REG_FLUSH_REGIONS_TYPE_4 0x40014
+#define PRS_REG_FLUSH_REGIONS_TYPE_5 0x40018
+#define PRS_REG_FLUSH_REGIONS_TYPE_6 0x4001c
+#define PRS_REG_FLUSH_REGIONS_TYPE_7 0x40020
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
+ * Ethernet header. */
+#define PRS_REG_HDRS_AFTER_BASIC 0x40238
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after the basic
+ * Ethernet header for port 0 packets. */
+#define PRS_REG_HDRS_AFTER_BASIC_PORT_0 0x40270
+#define PRS_REG_HDRS_AFTER_BASIC_PORT_1 0x40290
+/* [R 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 */
+#define PRS_REG_HDRS_AFTER_TAG_0 0x40248
+/* [RW 6] Bit-map indicating which L2 hdrs may appear after L2 tag 0 for
+ * port 0 packets */
+#define PRS_REG_HDRS_AFTER_TAG_0_PORT_0 0x40280
+#define PRS_REG_HDRS_AFTER_TAG_0_PORT_1 0x402a0
+/* [RW 4] The increment value to send in the CFC load request message */
+#define PRS_REG_INC_VALUE 0x40048
+/* [RW 6] Bit-map indicating which headers must appear in the packet */
+#define PRS_REG_MUST_HAVE_HDRS 0x40254
+/* [RW 6] Bit-map indicating which headers must appear in the packet for
+ * port 0 packets */
+#define PRS_REG_MUST_HAVE_HDRS_PORT_0 0x4028c
+#define PRS_REG_MUST_HAVE_HDRS_PORT_1 0x402ac
+#define PRS_REG_NIC_MODE 0x40138
+/* [RW 8] The 8-bit event ID for cases where there is no match on the
+ connection. Used in packet start message to TCM. */
+#define PRS_REG_NO_MATCH_EVENT_ID 0x40070
+/* [ST 24] The number of input CFC flush packets */
+#define PRS_REG_NUM_OF_CFC_FLUSH_MESSAGES 0x40128
+/* [ST 32] The number of cycles the Parser halted its operation since it
+ could not allocate the next serial number */
+#define PRS_REG_NUM_OF_DEAD_CYCLES 0x40130
+/* [ST 24] The number of input packets */
+#define PRS_REG_NUM_OF_PACKETS 0x40124
+/* [ST 24] The number of input transparent flush packets */
+#define PRS_REG_NUM_OF_TRANSPARENT_FLUSH_MESSAGES 0x4012c
+/* [RW 8] Context region for received Ethernet packet with a match and
+ packet type 0. Used in CFC load request message */
+#define PRS_REG_PACKET_REGIONS_TYPE_0 0x40028
+#define PRS_REG_PACKET_REGIONS_TYPE_1 0x4002c
+#define PRS_REG_PACKET_REGIONS_TYPE_2 0x40030
+#define PRS_REG_PACKET_REGIONS_TYPE_3 0x40034
+#define PRS_REG_PACKET_REGIONS_TYPE_4 0x40038
+#define PRS_REG_PACKET_REGIONS_TYPE_5 0x4003c
+#define PRS_REG_PACKET_REGIONS_TYPE_6 0x40040
+#define PRS_REG_PACKET_REGIONS_TYPE_7 0x40044
+/* [R 2] debug only: Number of pending requests for CAC on port 0. */
+#define PRS_REG_PENDING_BRB_CAC0_RQ 0x40174
+/* [R 2] debug only: Number of pending requests for header parsing. */
+#define PRS_REG_PENDING_BRB_PRS_RQ 0x40170
+/* [R 1] Interrupt register #0 read */
+#define PRS_REG_PRS_INT_STS 0x40188
+/* [RW 8] Parity mask register #0 read/write */
+#define PRS_REG_PRS_PRTY_MASK 0x401a4
+/* [R 8] Parity register #0 read */
+#define PRS_REG_PRS_PRTY_STS 0x40198
+/* [RC 8] Parity register #0 read clear */
+#define PRS_REG_PRS_PRTY_STS_CLR 0x4019c
+/* [RW 8] Context region for pure acknowledge packets. Used in CFC load
+ request message */
+#define PRS_REG_PURE_REGIONS 0x40024
+/* [R 32] debug only: Serial number status lsb 32 bits. '1' indicates this
+ serail number was released by SDM but cannot be used because a previous
+ serial number was not released. */
+#define PRS_REG_SERIAL_NUM_STATUS_LSB 0x40154
+/* [R 32] debug only: Serial number status msb 32 bits. '1' indicates this
+ serail number was released by SDM but cannot be used because a previous
+ serial number was not released. */
+#define PRS_REG_SERIAL_NUM_STATUS_MSB 0x40158
+/* [R 4] debug only: SRC current credit. Transaction based. */
+#define PRS_REG_SRC_CURRENT_CREDIT 0x4016c
+/* [RW 16] The Ethernet type value for L2 tag 0 */
+#define PRS_REG_TAG_ETHERTYPE_0 0x401d4
+/* [RW 4] The length of the info field for L2 tag 0. The length is between
+ * 2B and 14B; in 2B granularity */
+#define PRS_REG_TAG_LEN_0 0x4022c
+/* [R 8] debug only: TCM current credit. Cycle based. */
+#define PRS_REG_TCM_CURRENT_CREDIT 0x40160
+/* [R 8] debug only: TSDM current credit. Transaction based. */
+#define PRS_REG_TSDM_CURRENT_CREDIT 0x4015c
+#define PXP2_PXP2_INT_MASK_0_REG_PGL_CPL_AFT (0x1<<19)
+#define PXP2_PXP2_INT_MASK_0_REG_PGL_CPL_OF (0x1<<20)
+#define PXP2_PXP2_INT_MASK_0_REG_PGL_PCIE_ATTN (0x1<<22)
+#define PXP2_PXP2_INT_MASK_0_REG_PGL_READ_BLOCKED (0x1<<23)
+#define PXP2_PXP2_INT_MASK_0_REG_PGL_WRITE_BLOCKED (0x1<<24)
+#define PXP2_PXP2_INT_STS_0_REG_WR_PGLUE_EOP_ERROR (0x1<<7)
+#define PXP2_PXP2_INT_STS_CLR_0_REG_WR_PGLUE_EOP_ERROR (0x1<<7)
+/* [R 6] Debug only: Number of used entries in the data FIFO */
+#define PXP2_REG_HST_DATA_FIFO_STATUS 0x12047c
+/* [R 7] Debug only: Number of used entries in the header FIFO */
+#define PXP2_REG_HST_HEADER_FIFO_STATUS 0x120478
+#define PXP2_REG_PGL_ADDR_88_F0 0x120534
+/* [R 32] GRC address for configuration access to PCIE config address 0x88.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_88_F1 0x120544
+#define PXP2_REG_PGL_ADDR_8C_F0 0x120538
+/* [R 32] GRC address for configuration access to PCIE config address 0x8c.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_8C_F1 0x120548
+#define PXP2_REG_PGL_ADDR_90_F0 0x12053c
+/* [R 32] GRC address for configuration access to PCIE config address 0x90.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_90_F1 0x12054c
+#define PXP2_REG_PGL_ADDR_94_F0 0x120540
+/* [R 32] GRC address for configuration access to PCIE config address 0x94.
+ * any write to this PCIE address will cause a GRC write access to the
+ * address that's in t this register */
+#define PXP2_REG_PGL_ADDR_94_F1 0x120550
+#define PXP2_REG_PGL_CONTROL0 0x120490
+#define PXP2_REG_PGL_CONTROL1 0x120514
+#define PXP2_REG_PGL_DEBUG 0x120520
+/* [RW 32] third dword data of expansion rom request. this register is
+ special. reading from it provides a vector outstanding read requests. if
+ a bit is zero it means that a read request on the corresponding tag did
+ not finish yet (not all completions have arrived for it) */
+#define PXP2_REG_PGL_EXP_ROM2 0x120808
+/* [RW 32] Inbound interrupt table for CSDM: bits[31:16]-mask;
+ its[15:0]-address */
+#define PXP2_REG_PGL_INT_CSDM_0 0x1204f4
+#define PXP2_REG_PGL_INT_CSDM_1 0x1204f8
+#define PXP2_REG_PGL_INT_CSDM_2 0x1204fc
+#define PXP2_REG_PGL_INT_CSDM_3 0x120500
+#define PXP2_REG_PGL_INT_CSDM_4 0x120504
+#define PXP2_REG_PGL_INT_CSDM_5 0x120508
+#define PXP2_REG_PGL_INT_CSDM_6 0x12050c
+#define PXP2_REG_PGL_INT_CSDM_7 0x120510
+/* [RW 32] Inbound interrupt table for TSDM: bits[31:16]-mask;
+ its[15:0]-address */
+#define PXP2_REG_PGL_INT_TSDM_0 0x120494
+#define PXP2_REG_PGL_INT_TSDM_1 0x120498
+#define PXP2_REG_PGL_INT_TSDM_2 0x12049c
+#define PXP2_REG_PGL_INT_TSDM_3 0x1204a0
+#define PXP2_REG_PGL_INT_TSDM_4 0x1204a4
+#define PXP2_REG_PGL_INT_TSDM_5 0x1204a8
+#define PXP2_REG_PGL_INT_TSDM_6 0x1204ac
+#define PXP2_REG_PGL_INT_TSDM_7 0x1204b0
+/* [RW 32] Inbound interrupt table for USDM: bits[31:16]-mask;
+ its[15:0]-address */
+#define PXP2_REG_PGL_INT_USDM_0 0x1204b4
+#define PXP2_REG_PGL_INT_USDM_1 0x1204b8
+#define PXP2_REG_PGL_INT_USDM_2 0x1204bc
+#define PXP2_REG_PGL_INT_USDM_3 0x1204c0
+#define PXP2_REG_PGL_INT_USDM_4 0x1204c4
+#define PXP2_REG_PGL_INT_USDM_5 0x1204c8
+#define PXP2_REG_PGL_INT_USDM_6 0x1204cc
+#define PXP2_REG_PGL_INT_USDM_7 0x1204d0
+/* [RW 32] Inbound interrupt table for XSDM: bits[31:16]-mask;
+ its[15:0]-address */
+#define PXP2_REG_PGL_INT_XSDM_0 0x1204d4
+#define PXP2_REG_PGL_INT_XSDM_1 0x1204d8
+#define PXP2_REG_PGL_INT_XSDM_2 0x1204dc
+#define PXP2_REG_PGL_INT_XSDM_3 0x1204e0
+#define PXP2_REG_PGL_INT_XSDM_4 0x1204e4
+#define PXP2_REG_PGL_INT_XSDM_5 0x1204e8
+#define PXP2_REG_PGL_INT_XSDM_6 0x1204ec
+#define PXP2_REG_PGL_INT_XSDM_7 0x1204f0
+/* [RW 3] this field allows one function to pretend being another function
+ when accessing any BAR mapped resource within the device. the value of
+ the field is the number of the function that will be accessed
+ effectively. after software write to this bit it must read it in order to
+ know that the new value is updated */
+#define PXP2_REG_PGL_PRETEND_FUNC_F0 0x120674
+#define PXP2_REG_PGL_PRETEND_FUNC_F1 0x120678
+#define PXP2_REG_PGL_PRETEND_FUNC_F2 0x12067c
+#define PXP2_REG_PGL_PRETEND_FUNC_F3 0x120680
+#define PXP2_REG_PGL_PRETEND_FUNC_F4 0x120684
+#define PXP2_REG_PGL_PRETEND_FUNC_F5 0x120688
+#define PXP2_REG_PGL_PRETEND_FUNC_F6 0x12068c
+#define PXP2_REG_PGL_PRETEND_FUNC_F7 0x120690
+/* [R 1] this bit indicates that a read request was blocked because of
+ bus_master_en was deasserted */
+#define PXP2_REG_PGL_READ_BLOCKED 0x120568
+#define PXP2_REG_PGL_TAGS_LIMIT 0x1205a8
+/* [R 18] debug only */
+#define PXP2_REG_PGL_TXW_CDTS 0x12052c
+/* [R 1] this bit indicates that a write request was blocked because of
+ bus_master_en was deasserted */
+#define PXP2_REG_PGL_WRITE_BLOCKED 0x120564
+#define PXP2_REG_PSWRQ_BW_ADD1 0x1201c0
+#define PXP2_REG_PSWRQ_BW_ADD10 0x1201e4
+#define PXP2_REG_PSWRQ_BW_ADD11 0x1201e8
+#define PXP2_REG_PSWRQ_BW_ADD2 0x1201c4
+#define PXP2_REG_PSWRQ_BW_ADD28 0x120228
+#define PXP2_REG_PSWRQ_BW_ADD3 0x1201c8
+#define PXP2_REG_PSWRQ_BW_ADD6 0x1201d4
+#define PXP2_REG_PSWRQ_BW_ADD7 0x1201d8
+#define PXP2_REG_PSWRQ_BW_ADD8 0x1201dc
+#define PXP2_REG_PSWRQ_BW_ADD9 0x1201e0
+#define PXP2_REG_PSWRQ_BW_CREDIT 0x12032c
+#define PXP2_REG_PSWRQ_BW_L1 0x1202b0
+#define PXP2_REG_PSWRQ_BW_L10 0x1202d4
+#define PXP2_REG_PSWRQ_BW_L11 0x1202d8
+#define PXP2_REG_PSWRQ_BW_L2 0x1202b4
+#define PXP2_REG_PSWRQ_BW_L28 0x120318
+#define PXP2_REG_PSWRQ_BW_L3 0x1202b8
+#define PXP2_REG_PSWRQ_BW_L6 0x1202c4
+#define PXP2_REG_PSWRQ_BW_L7 0x1202c8
+#define PXP2_REG_PSWRQ_BW_L8 0x1202cc
+#define PXP2_REG_PSWRQ_BW_L9 0x1202d0
+#define PXP2_REG_PSWRQ_BW_RD 0x120324
+#define PXP2_REG_PSWRQ_BW_UB1 0x120238
+#define PXP2_REG_PSWRQ_BW_UB10 0x12025c
+#define PXP2_REG_PSWRQ_BW_UB11 0x120260
+#define PXP2_REG_PSWRQ_BW_UB2 0x12023c
+#define PXP2_REG_PSWRQ_BW_UB28 0x1202a0
+#define PXP2_REG_PSWRQ_BW_UB3 0x120240
+#define PXP2_REG_PSWRQ_BW_UB6 0x12024c
+#define PXP2_REG_PSWRQ_BW_UB7 0x120250
+#define PXP2_REG_PSWRQ_BW_UB8 0x120254
+#define PXP2_REG_PSWRQ_BW_UB9 0x120258
+#define PXP2_REG_PSWRQ_BW_WR 0x120328
+#define PXP2_REG_PSWRQ_CDU0_L2P 0x120000
+#define PXP2_REG_PSWRQ_QM0_L2P 0x120038
+#define PXP2_REG_PSWRQ_SRC0_L2P 0x120054
+#define PXP2_REG_PSWRQ_TM0_L2P 0x12001c
+#define PXP2_REG_PSWRQ_TSDM0_L2P 0x1200e0
+/* [RW 32] Interrupt mask register #0 read/write */
+#define PXP2_REG_PXP2_INT_MASK_0 0x120578
+/* [R 32] Interrupt register #0 read */
+#define PXP2_REG_PXP2_INT_STS_0 0x12056c
+#define PXP2_REG_PXP2_INT_STS_1 0x120608
+/* [RC 32] Interrupt register #0 read clear */
+#define PXP2_REG_PXP2_INT_STS_CLR_0 0x120570
+/* [RW 32] Parity mask register #0 read/write */
+#define PXP2_REG_PXP2_PRTY_MASK_0 0x120588
+#define PXP2_REG_PXP2_PRTY_MASK_1 0x120598
+/* [R 32] Parity register #0 read */
+#define PXP2_REG_PXP2_PRTY_STS_0 0x12057c
+#define PXP2_REG_PXP2_PRTY_STS_1 0x12058c
+/* [RC 32] Parity register #0 read clear */
+#define PXP2_REG_PXP2_PRTY_STS_CLR_0 0x120580
+#define PXP2_REG_PXP2_PRTY_STS_CLR_1 0x120590
+/* [R 1] Debug only: The 'almost full' indication from each fifo (gives
+ indication about backpressure) */
+#define PXP2_REG_RD_ALMOST_FULL_0 0x120424
+/* [R 8] Debug only: The blocks counter - number of unused block ids */
+#define PXP2_REG_RD_BLK_CNT 0x120418
+/* [RW 8] Debug only: Total number of available blocks in Tetris Buffer.
+ Must be bigger than 6. Normally should not be changed. */
+#define PXP2_REG_RD_BLK_NUM_CFG 0x12040c
+/* [RW 2] CDU byte swapping mode configuration for master read requests */
+#define PXP2_REG_RD_CDURD_SWAP_MODE 0x120404
+/* [RW 1] When '1'; inputs to the PSWRD block are ignored */
+#define PXP2_REG_RD_DISABLE_INPUTS 0x120374
+/* [R 1] PSWRD internal memories initialization is done */
+#define PXP2_REG_RD_INIT_DONE 0x120370
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq10 */
+#define PXP2_REG_RD_MAX_BLKS_VQ10 0x1203a0
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq11 */
+#define PXP2_REG_RD_MAX_BLKS_VQ11 0x1203a4
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq17 */
+#define PXP2_REG_RD_MAX_BLKS_VQ17 0x1203bc
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq18 */
+#define PXP2_REG_RD_MAX_BLKS_VQ18 0x1203c0
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq19 */
+#define PXP2_REG_RD_MAX_BLKS_VQ19 0x1203c4
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq22 */
+#define PXP2_REG_RD_MAX_BLKS_VQ22 0x1203d0
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq25 */
+#define PXP2_REG_RD_MAX_BLKS_VQ25 0x1203dc
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq6 */
+#define PXP2_REG_RD_MAX_BLKS_VQ6 0x120390
+/* [RW 8] The maximum number of blocks in Tetris Buffer that can be
+ allocated for vq9 */
+#define PXP2_REG_RD_MAX_BLKS_VQ9 0x12039c
+/* [RW 2] PBF byte swapping mode configuration for master read requests */
+#define PXP2_REG_RD_PBF_SWAP_MODE 0x1203f4
+/* [R 1] Debug only: Indication if delivery ports are idle */
+#define PXP2_REG_RD_PORT_IS_IDLE_0 0x12041c
+#define PXP2_REG_RD_PORT_IS_IDLE_1 0x120420
+/* [RW 2] QM byte swapping mode configuration for master read requests */
+#define PXP2_REG_RD_QM_SWAP_MODE 0x1203f8
+/* [R 7] Debug only: The SR counter - number of unused sub request ids */
+#define PXP2_REG_RD_SR_CNT 0x120414
+/* [RW 2] SRC byte swapping mode configuration for master read requests */
+#define PXP2_REG_RD_SRC_SWAP_MODE 0x120400
+/* [RW 7] Debug only: Total number of available PCI read sub-requests. Must
+ be bigger than 1. Normally should not be changed. */
+#define PXP2_REG_RD_SR_NUM_CFG 0x120408
+/* [RW 1] Signals the PSWRD block to start initializing internal memories */
+#define PXP2_REG_RD_START_INIT 0x12036c
+/* [RW 2] TM byte swapping mode configuration for master read requests */
+#define PXP2_REG_RD_TM_SWAP_MODE 0x1203fc
+/* [RW 10] Bandwidth addition to VQ0 write requests */
+#define PXP2_REG_RQ_BW_RD_ADD0 0x1201bc
+/* [RW 10] Bandwidth addition to VQ12 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD12 0x1201ec
+/* [RW 10] Bandwidth addition to VQ13 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD13 0x1201f0
+/* [RW 10] Bandwidth addition to VQ14 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD14 0x1201f4
+/* [RW 10] Bandwidth addition to VQ15 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD15 0x1201f8
+/* [RW 10] Bandwidth addition to VQ16 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD16 0x1201fc
+/* [RW 10] Bandwidth addition to VQ17 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD17 0x120200
+/* [RW 10] Bandwidth addition to VQ18 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD18 0x120204
+/* [RW 10] Bandwidth addition to VQ19 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD19 0x120208
+/* [RW 10] Bandwidth addition to VQ20 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD20 0x12020c
+/* [RW 10] Bandwidth addition to VQ22 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD22 0x120210
+/* [RW 10] Bandwidth addition to VQ23 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD23 0x120214
+/* [RW 10] Bandwidth addition to VQ24 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD24 0x120218
+/* [RW 10] Bandwidth addition to VQ25 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD25 0x12021c
+/* [RW 10] Bandwidth addition to VQ26 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD26 0x120220
+/* [RW 10] Bandwidth addition to VQ27 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD27 0x120224
+/* [RW 10] Bandwidth addition to VQ4 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD4 0x1201cc
+/* [RW 10] Bandwidth addition to VQ5 read requests */
+#define PXP2_REG_RQ_BW_RD_ADD5 0x1201d0
+/* [RW 10] Bandwidth Typical L for VQ0 Read requests */
+#define PXP2_REG_RQ_BW_RD_L0 0x1202ac
+/* [RW 10] Bandwidth Typical L for VQ12 Read requests */
+#define PXP2_REG_RQ_BW_RD_L12 0x1202dc
+/* [RW 10] Bandwidth Typical L for VQ13 Read requests */
+#define PXP2_REG_RQ_BW_RD_L13 0x1202e0
+/* [RW 10] Bandwidth Typical L for VQ14 Read requests */
+#define PXP2_REG_RQ_BW_RD_L14 0x1202e4
+/* [RW 10] Bandwidth Typical L for VQ15 Read requests */
+#define PXP2_REG_RQ_BW_RD_L15 0x1202e8
+/* [RW 10] Bandwidth Typical L for VQ16 Read requests */
+#define PXP2_REG_RQ_BW_RD_L16 0x1202ec
+/* [RW 10] Bandwidth Typical L for VQ17 Read requests */
+#define PXP2_REG_RQ_BW_RD_L17 0x1202f0
+/* [RW 10] Bandwidth Typical L for VQ18 Read requests */
+#define PXP2_REG_RQ_BW_RD_L18 0x1202f4
+/* [RW 10] Bandwidth Typical L for VQ19 Read requests */
+#define PXP2_REG_RQ_BW_RD_L19 0x1202f8
+/* [RW 10] Bandwidth Typical L for VQ20 Read requests */
+#define PXP2_REG_RQ_BW_RD_L20 0x1202fc
+/* [RW 10] Bandwidth Typical L for VQ22 Read requests */
+#define PXP2_REG_RQ_BW_RD_L22 0x120300
+/* [RW 10] Bandwidth Typical L for VQ23 Read requests */
+#define PXP2_REG_RQ_BW_RD_L23 0x120304
+/* [RW 10] Bandwidth Typical L for VQ24 Read requests */
+#define PXP2_REG_RQ_BW_RD_L24 0x120308
+/* [RW 10] Bandwidth Typical L for VQ25 Read requests */
+#define PXP2_REG_RQ_BW_RD_L25 0x12030c
+/* [RW 10] Bandwidth Typical L for VQ26 Read requests */
+#define PXP2_REG_RQ_BW_RD_L26 0x120310
+/* [RW 10] Bandwidth Typical L for VQ27 Read requests */
+#define PXP2_REG_RQ_BW_RD_L27 0x120314
+/* [RW 10] Bandwidth Typical L for VQ4 Read requests */
+#define PXP2_REG_RQ_BW_RD_L4 0x1202bc
+/* [RW 10] Bandwidth Typical L for VQ5 Read- currently not used */
+#define PXP2_REG_RQ_BW_RD_L5 0x1202c0
+/* [RW 7] Bandwidth upper bound for VQ0 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND0 0x120234
+/* [RW 7] Bandwidth upper bound for VQ12 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND12 0x120264
+/* [RW 7] Bandwidth upper bound for VQ13 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND13 0x120268
+/* [RW 7] Bandwidth upper bound for VQ14 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND14 0x12026c
+/* [RW 7] Bandwidth upper bound for VQ15 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND15 0x120270
+/* [RW 7] Bandwidth upper bound for VQ16 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND16 0x120274
+/* [RW 7] Bandwidth upper bound for VQ17 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND17 0x120278
+/* [RW 7] Bandwidth upper bound for VQ18 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND18 0x12027c
+/* [RW 7] Bandwidth upper bound for VQ19 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND19 0x120280
+/* [RW 7] Bandwidth upper bound for VQ20 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND20 0x120284
+/* [RW 7] Bandwidth upper bound for VQ22 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND22 0x120288
+/* [RW 7] Bandwidth upper bound for VQ23 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND23 0x12028c
+/* [RW 7] Bandwidth upper bound for VQ24 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND24 0x120290
+/* [RW 7] Bandwidth upper bound for VQ25 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND25 0x120294
+/* [RW 7] Bandwidth upper bound for VQ26 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND26 0x120298
+/* [RW 7] Bandwidth upper bound for VQ27 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND27 0x12029c
+/* [RW 7] Bandwidth upper bound for VQ4 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND4 0x120244
+/* [RW 7] Bandwidth upper bound for VQ5 read requests */
+#define PXP2_REG_RQ_BW_RD_UBOUND5 0x120248
+/* [RW 10] Bandwidth addition to VQ29 write requests */
+#define PXP2_REG_RQ_BW_WR_ADD29 0x12022c
+/* [RW 10] Bandwidth addition to VQ30 write requests */
+#define PXP2_REG_RQ_BW_WR_ADD30 0x120230
+/* [RW 10] Bandwidth Typical L for VQ29 Write requests */
+#define PXP2_REG_RQ_BW_WR_L29 0x12031c
+/* [RW 10] Bandwidth Typical L for VQ30 Write requests */
+#define PXP2_REG_RQ_BW_WR_L30 0x120320
+/* [RW 7] Bandwidth upper bound for VQ29 */
+#define PXP2_REG_RQ_BW_WR_UBOUND29 0x1202a4
+/* [RW 7] Bandwidth upper bound for VQ30 */
+#define PXP2_REG_RQ_BW_WR_UBOUND30 0x1202a8
+/* [RW 18] external first_mem_addr field in L2P table for CDU module port 0 */
+#define PXP2_REG_RQ_CDU0_EFIRST_MEM_ADDR 0x120008
+/* [RW 2] Endian mode for cdu */
+#define PXP2_REG_RQ_CDU_ENDIAN_M 0x1201a0
+#define PXP2_REG_RQ_CDU_FIRST_ILT 0x12061c
+#define PXP2_REG_RQ_CDU_LAST_ILT 0x120620
+/* [RW 3] page size in L2P table for CDU module; -4k; -8k; -16k; -32k; -64k;
+ -128k */
+#define PXP2_REG_RQ_CDU_P_SIZE 0x120018
+/* [R 1] 1' indicates that the requester has finished its internal
+ configuration */
+#define PXP2_REG_RQ_CFG_DONE 0x1201b4
+/* [RW 2] Endian mode for debug */
+#define PXP2_REG_RQ_DBG_ENDIAN_M 0x1201a4
+/* [RW 1] When '1'; requests will enter input buffers but wont get out
+ towards the glue */
+#define PXP2_REG_RQ_DISABLE_INPUTS 0x120330
+/* [RW 4] Determines alignment of write SRs when a request is split into
+ * several SRs. 0 - 8B aligned. 1 - 64B aligned. 2 - 128B aligned. 3 - 256B
+ * aligned. 4 - 512B aligned. */
+#define PXP2_REG_RQ_DRAM_ALIGN 0x1205b0
+/* [RW 4] Determines alignment of read SRs when a request is split into
+ * several SRs. 0 - 8B aligned. 1 - 64B aligned. 2 - 128B aligned. 3 - 256B
+ * aligned. 4 - 512B aligned. */
+#define PXP2_REG_RQ_DRAM_ALIGN_RD 0x12092c
+/* [RW 1] when set the new alignment method (E2) will be applied; when reset
+ * the original alignment method (E1 E1H) will be applied */
+#define PXP2_REG_RQ_DRAM_ALIGN_SEL 0x120930
+/* [RW 1] If 1 ILT failiue will not result in ELT access; An interrupt will
+ be asserted */
+#define PXP2_REG_RQ_ELT_DISABLE 0x12066c
+/* [RW 2] Endian mode for hc */
+#define PXP2_REG_RQ_HC_ENDIAN_M 0x1201a8
+/* [RW 1] when '0' ILT logic will work as in A0; otherwise B0; for back
+ compatibility needs; Note that different registers are used per mode */
+#define PXP2_REG_RQ_ILT_MODE 0x1205b4
+/* [WB 53] Onchip address table */
+#define PXP2_REG_RQ_ONCHIP_AT 0x122000
+/* [WB 53] Onchip address table - B0 */
+#define PXP2_REG_RQ_ONCHIP_AT_B0 0x128000
+/* [RW 13] Pending read limiter threshold; in Dwords */
+#define PXP2_REG_RQ_PDR_LIMIT 0x12033c
+/* [RW 2] Endian mode for qm */
+#define PXP2_REG_RQ_QM_ENDIAN_M 0x120194
+#define PXP2_REG_RQ_QM_FIRST_ILT 0x120634
+#define PXP2_REG_RQ_QM_LAST_ILT 0x120638
+/* [RW 3] page size in L2P table for QM module; -4k; -8k; -16k; -32k; -64k;
+ -128k */
+#define PXP2_REG_RQ_QM_P_SIZE 0x120050
+/* [RW 1] 1' indicates that the RBC has finished configuring the PSWRQ */
+#define PXP2_REG_RQ_RBC_DONE 0x1201b0
+/* [RW 3] Max burst size filed for read requests port 0; 000 - 128B;
+ 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
+#define PXP2_REG_RQ_RD_MBS0 0x120160
+/* [RW 3] Max burst size filed for read requests port 1; 000 - 128B;
+ 001:256B; 010: 512B; 11:1K:100:2K; 01:4K */
+#define PXP2_REG_RQ_RD_MBS1 0x120168
+/* [RW 2] Endian mode for src */
+#define PXP2_REG_RQ_SRC_ENDIAN_M 0x12019c
+#define PXP2_REG_RQ_SRC_FIRST_ILT 0x12063c
+#define PXP2_REG_RQ_SRC_LAST_ILT 0x120640
+/* [RW 3] page size in L2P table for SRC module; -4k; -8k; -16k; -32k; -64k;
+ -128k */
+#define PXP2_REG_RQ_SRC_P_SIZE 0x12006c
+/* [RW 2] Endian mode for tm */
+#define PXP2_REG_RQ_TM_ENDIAN_M 0x120198
+#define PXP2_REG_RQ_TM_FIRST_ILT 0x120644
+#define PXP2_REG_RQ_TM_LAST_ILT 0x120648
+/* [RW 3] page size in L2P table for TM module; -4k; -8k; -16k; -32k; -64k;
+ -128k */
+#define PXP2_REG_RQ_TM_P_SIZE 0x120034
+/* [R 5] Number of entries in the ufifo; his fifo has l2p completions */
+#define PXP2_REG_RQ_UFIFO_NUM_OF_ENTRY 0x12080c
+/* [RW 18] external first_mem_addr field in L2P table for USDM module port 0 */
+#define PXP2_REG_RQ_USDM0_EFIRST_MEM_ADDR 0x120094
+/* [R 8] Number of entries occupied by vq 0 in pswrq memory */
+#define PXP2_REG_RQ_VQ0_ENTRY_CNT 0x120810
+/* [R 8] Number of entries occupied by vq 10 in pswrq memory */
+#define PXP2_REG_RQ_VQ10_ENTRY_CNT 0x120818
+/* [R 8] Number of entries occupied by vq 11 in pswrq memory */
+#define PXP2_REG_RQ_VQ11_ENTRY_CNT 0x120820
+/* [R 8] Number of entries occupied by vq 12 in pswrq memory */
+#define PXP2_REG_RQ_VQ12_ENTRY_CNT 0x120828
+/* [R 8] Number of entries occupied by vq 13 in pswrq memory */
+#define PXP2_REG_RQ_VQ13_ENTRY_CNT 0x120830
+/* [R 8] Number of entries occupied by vq 14 in pswrq memory */
+#define PXP2_REG_RQ_VQ14_ENTRY_CNT 0x120838
+/* [R 8] Number of entries occupied by vq 15 in pswrq memory */
+#define PXP2_REG_RQ_VQ15_ENTRY_CNT 0x120840
+/* [R 8] Number of entries occupied by vq 16 in pswrq memory */
+#define PXP2_REG_RQ_VQ16_ENTRY_CNT 0x120848
+/* [R 8] Number of entries occupied by vq 17 in pswrq memory */
+#define PXP2_REG_RQ_VQ17_ENTRY_CNT 0x120850
+/* [R 8] Number of entries occupied by vq 18 in pswrq memory */
+#define PXP2_REG_RQ_VQ18_ENTRY_CNT 0x120858
+/* [R 8] Number of entries occupied by vq 19 in pswrq memory */
+#define PXP2_REG_RQ_VQ19_ENTRY_CNT 0x120860
+/* [R 8] Number of entries occupied by vq 1 in pswrq memory */
+#define PXP2_REG_RQ_VQ1_ENTRY_CNT 0x120868
+/* [R 8] Number of entries occupied by vq 20 in pswrq memory */
+#define PXP2_REG_RQ_VQ20_ENTRY_CNT 0x120870
+/* [R 8] Number of entries occupied by vq 21 in pswrq memory */
+#define PXP2_REG_RQ_VQ21_ENTRY_CNT 0x120878
+/* [R 8] Number of entries occupied by vq 22 in pswrq memory */
+#define PXP2_REG_RQ_VQ22_ENTRY_CNT 0x120880
+/* [R 8] Number of entries occupied by vq 23 in pswrq memory */
+#define PXP2_REG_RQ_VQ23_ENTRY_CNT 0x120888
+/* [R 8] Number of entries occupied by vq 24 in pswrq memory */
+#define PXP2_REG_RQ_VQ24_ENTRY_CNT 0x120890
+/* [R 8] Number of entries occupied by vq 25 in pswrq memory */
+#define PXP2_REG_RQ_VQ25_ENTRY_CNT 0x120898
+/* [R 8] Number of entries occupied by vq 26 in pswrq memory */
+#define PXP2_REG_RQ_VQ26_ENTRY_CNT 0x1208a0
+/* [R 8] Number of entries occupied by vq 27 in pswrq memory */
+#define PXP2_REG_RQ_VQ27_ENTRY_CNT 0x1208a8
+/* [R 8] Number of entries occupied by vq 28 in pswrq memory */
+#define PXP2_REG_RQ_VQ28_ENTRY_CNT 0x1208b0
+/* [R 8] Number of entries occupied by vq 29 in pswrq memory */
+#define PXP2_REG_RQ_VQ29_ENTRY_CNT 0x1208b8
+/* [R 8] Number of entries occupied by vq 2 in pswrq memory */
+#define PXP2_REG_RQ_VQ2_ENTRY_CNT 0x1208c0
+/* [R 8] Number of entries occupied by vq 30 in pswrq memory */
+#define PXP2_REG_RQ_VQ30_ENTRY_CNT 0x1208c8
+/* [R 8] Number of entries occupied by vq 31 in pswrq memory */
+#define PXP2_REG_RQ_VQ31_ENTRY_CNT 0x1208d0
+/* [R 8] Number of entries occupied by vq 3 in pswrq memory */
+#define PXP2_REG_RQ_VQ3_ENTRY_CNT 0x1208d8
+/* [R 8] Number of entries occupied by vq 4 in pswrq memory */
+#define PXP2_REG_RQ_VQ4_ENTRY_CNT 0x1208e0
+/* [R 8] Number of entries occupied by vq 5 in pswrq memory */
+#define PXP2_REG_RQ_VQ5_ENTRY_CNT 0x1208e8
+/* [R 8] Number of entries occupied by vq 6 in pswrq memory */
+#define PXP2_REG_RQ_VQ6_ENTRY_CNT 0x1208f0
+/* [R 8] Number of entries occupied by vq 7 in pswrq memory */
+#define PXP2_REG_RQ_VQ7_ENTRY_CNT 0x1208f8
+/* [R 8] Number of entries occupied by vq 8 in pswrq memory */
+#define PXP2_REG_RQ_VQ8_ENTRY_CNT 0x120900
+/* [R 8] Number of entries occupied by vq 9 in pswrq memory */
+#define PXP2_REG_RQ_VQ9_ENTRY_CNT 0x120908
+/* [RW 3] Max burst size filed for write requests port 0; 000 - 128B;
+ 001:256B; 010: 512B; */
+#define PXP2_REG_RQ_WR_MBS0 0x12015c
+/* [RW 3] Max burst size filed for write requests port 1; 000 - 128B;
+ 001:256B; 010: 512B; */
+#define PXP2_REG_RQ_WR_MBS1 0x120164
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CDU_MPS 0x1205f0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_CSDM_MPS 0x1205d0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DBG_MPS 0x1205e8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_DMAE_MPS 0x1205ec
+/* [RW 10] if Number of entries in dmae fifo will be higher than this
+ threshold then has_payload indication will be asserted; the default value
+ should be equal to > write MBS size! */
+#define PXP2_REG_WR_DMAE_TH 0x120368
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_HC_MPS 0x1205c8
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_QM_MPS 0x1205dc
+/* [RW 1] 0 - working in A0 mode; - working in B0 mode */
+#define PXP2_REG_WR_REV_MODE 0x120670
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_SRC_MPS 0x1205e4
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TM_MPS 0x1205e0
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_TSDM_MPS 0x1205d4
+/* [RW 10] if Number of entries in usdmdp fifo will be higher than this
+ threshold then has_payload indication will be asserted; the default value
+ should be equal to > write MBS size! */
+#define PXP2_REG_WR_USDMDP_TH 0x120348
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_USDM_MPS 0x1205cc
+/* [RW 2] 0 - 128B; - 256B; - 512B; - 1024B; when the payload in the
+ buffer reaches this number has_payload will be asserted */
+#define PXP2_REG_WR_XSDM_MPS 0x1205d8
+/* [R 1] debug only: Indication if PSWHST arbiter is idle */
+#define PXP_REG_HST_ARB_IS_IDLE 0x103004
+/* [R 8] debug only: A bit mask for all PSWHST arbiter clients. '1' means
+ this client is waiting for the arbiter. */
+#define PXP_REG_HST_CLIENTS_WAITING_TO_ARB 0x103008
+/* [RW 1] When 1; doorbells are discarded and not passed to doorbell queue
+ block. Should be used for close the gates. */
+#define PXP_REG_HST_DISCARD_DOORBELLS 0x1030a4
+/* [R 1] debug only: '1' means this PSWHST is discarding doorbells. This bit
+ should update according to 'hst_discard_doorbells' register when the state
+ machine is idle */
+#define PXP_REG_HST_DISCARD_DOORBELLS_STATUS 0x1030a0
+/* [RW 1] When 1; new internal writes arriving to the block are discarded.
+ Should be used for close the gates. */
+#define PXP_REG_HST_DISCARD_INTERNAL_WRITES 0x1030a8
+/* [R 6] debug only: A bit mask for all PSWHST internal write clients. '1'
+ means this PSWHST is discarding inputs from this client. Each bit should
+ update according to 'hst_discard_internal_writes' register when the state
+ machine is idle. */
+#define PXP_REG_HST_DISCARD_INTERNAL_WRITES_STATUS 0x10309c
+/* [WB 160] Used for initialization of the inbound interrupts memory */
+#define PXP_REG_HST_INBOUND_INT 0x103800
+/* [RW 7] Indirect access to the permission table. The fields are : {Valid;
+ * VFID[5:0]}
+ */
+#define PXP_REG_HST_ZONE_PERMISSION_TABLE 0x103400
+/* [RW 32] Interrupt mask register #0 read/write */
+#define PXP_REG_PXP_INT_MASK_0 0x103074
+#define PXP_REG_PXP_INT_MASK_1 0x103084
+/* [R 32] Interrupt register #0 read */
+#define PXP_REG_PXP_INT_STS_0 0x103068
+#define PXP_REG_PXP_INT_STS_1 0x103078
+/* [RC 32] Interrupt register #0 read clear */
+#define PXP_REG_PXP_INT_STS_CLR_0 0x10306c
+#define PXP_REG_PXP_INT_STS_CLR_1 0x10307c
+/* [RW 27] Parity mask register #0 read/write */
+#define PXP_REG_PXP_PRTY_MASK 0x103094
+/* [R 26] Parity register #0 read */
+#define PXP_REG_PXP_PRTY_STS 0x103088
+/* [RC 27] Parity register #0 read clear */
+#define PXP_REG_PXP_PRTY_STS_CLR 0x10308c
+/* [RW 4] The activity counter initial increment value sent in the load
+ request */
+#define QM_REG_ACTCTRINITVAL_0 0x168040
+#define QM_REG_ACTCTRINITVAL_1 0x168044
+#define QM_REG_ACTCTRINITVAL_2 0x168048
+#define QM_REG_ACTCTRINITVAL_3 0x16804c
+/* [RW 32] The base logical address (in bytes) of each physical queue. The
+ index I represents the physical queue number. The 12 lsbs are ignore and
+ considered zero so practically there are only 20 bits in this register;
+ queues 63-0 */
+#define QM_REG_BASEADDR 0x168900
+/* [RW 32] The base logical address (in bytes) of each physical queue. The
+ index I represents the physical queue number. The 12 lsbs are ignore and
+ considered zero so practically there are only 20 bits in this register;
+ queues 127-64 */
+#define QM_REG_BASEADDR_EXT_A 0x16e100
+/* [RW 16] The byte credit cost for each task. This value is for both ports */
+#define QM_REG_BYTECRDCOST 0x168234
+/* [RW 16] The initial byte credit value for both ports. */
+#define QM_REG_BYTECRDINITVAL 0x168238
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 31-0 */
+#define QM_REG_BYTECRDPORT_LSB 0x168228
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 95-64 */
+#define QM_REG_BYTECRDPORT_LSB_EXT_A 0x16e520
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 63-32 */
+#define QM_REG_BYTECRDPORT_MSB 0x168224
+/* [RW 32] A bit per physical queue. If the bit is cleared then the physical
+ queue uses port 0 else it uses port 1; queues 127-96 */
+#define QM_REG_BYTECRDPORT_MSB_EXT_A 0x16e51c
+/* [RW 16] The byte credit value that if above the QM is considered almost
+ full */
+#define QM_REG_BYTECREDITAFULLTHR 0x168094
+/* [RW 4] The initial credit for interface */
+#define QM_REG_CMINITCRD_0 0x1680cc
+#define QM_REG_BYTECRDCMDQ_0 0x16e6e8
+#define QM_REG_CMINITCRD_1 0x1680d0
+#define QM_REG_CMINITCRD_2 0x1680d4
+#define QM_REG_CMINITCRD_3 0x1680d8
+#define QM_REG_CMINITCRD_4 0x1680dc
+#define QM_REG_CMINITCRD_5 0x1680e0
+#define QM_REG_CMINITCRD_6 0x1680e4
+#define QM_REG_CMINITCRD_7 0x1680e8
+/* [RW 8] A mask bit per CM interface. If this bit is 0 then this interface
+ is masked */
+#define QM_REG_CMINTEN 0x1680ec
+/* [RW 12] A bit vector which indicates which one of the queues are tied to
+ interface 0 */
+#define QM_REG_CMINTVOQMASK_0 0x1681f4
+#define QM_REG_CMINTVOQMASK_1 0x1681f8
+#define QM_REG_CMINTVOQMASK_2 0x1681fc
+#define QM_REG_CMINTVOQMASK_3 0x168200
+#define QM_REG_CMINTVOQMASK_4 0x168204
+#define QM_REG_CMINTVOQMASK_5 0x168208
+#define QM_REG_CMINTVOQMASK_6 0x16820c
+#define QM_REG_CMINTVOQMASK_7 0x168210
+/* [RW 20] The number of connections divided by 16 which dictates the size
+ of each queue which belongs to even function number. */
+#define QM_REG_CONNNUM_0 0x168020
+/* [R 6] Keep the fill level of the fifo from write client 4 */
+#define QM_REG_CQM_WRC_FIFOLVL 0x168018
+/* [RW 8] The context regions sent in the CFC load request */
+#define QM_REG_CTXREG_0 0x168030
+#define QM_REG_CTXREG_1 0x168034
+#define QM_REG_CTXREG_2 0x168038
+#define QM_REG_CTXREG_3 0x16803c
+/* [RW 12] The VOQ mask used to select the VOQs which needs to be full for
+ bypass enable */
+#define QM_REG_ENBYPVOQMASK 0x16823c
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 31-0 */
+#define QM_REG_ENBYTECRD_LSB 0x168220
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 95-64 */
+#define QM_REG_ENBYTECRD_LSB_EXT_A 0x16e518
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 63-32 */
+#define QM_REG_ENBYTECRD_MSB 0x16821c
+/* [RW 32] A bit mask per each physical queue. If a bit is set then the
+ physical queue uses the byte credit; queues 127-96 */
+#define QM_REG_ENBYTECRD_MSB_EXT_A 0x16e514
+/* [RW 4] If cleared then the secondary interface will not be served by the
+ RR arbiter */
+#define QM_REG_ENSEC 0x1680f0
+/* [RW 32] NA */
+#define QM_REG_FUNCNUMSEL_LSB 0x168230
+/* [RW 32] NA */
+#define QM_REG_FUNCNUMSEL_MSB 0x16822c
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 31:0 */
+#define QM_REG_HWAEMPTYMASK_LSB 0x168218
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 95-64 */
+#define QM_REG_HWAEMPTYMASK_LSB_EXT_A 0x16e510
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 63:32 */
+#define QM_REG_HWAEMPTYMASK_MSB 0x168214
+/* [RW 32] A mask register to mask the Almost empty signals which will not
+ be use for the almost empty indication to the HW block; queues 127-96 */
+#define QM_REG_HWAEMPTYMASK_MSB_EXT_A 0x16e50c
+/* [RW 4] The number of outstanding request to CFC */
+#define QM_REG_OUTLDREQ 0x168804
+/* [RC 1] A flag to indicate that overflow error occurred in one of the
+ queues. */
+#define QM_REG_OVFERROR 0x16805c
+/* [RC 7] the Q where the overflow occurs */
+#define QM_REG_OVFQNUM 0x168058
+/* [R 16] Pause state for physical queues 15-0 */
+#define QM_REG_PAUSESTATE0 0x168410
+/* [R 16] Pause state for physical queues 31-16 */
+#define QM_REG_PAUSESTATE1 0x168414
+/* [R 16] Pause state for physical queues 47-32 */
+#define QM_REG_PAUSESTATE2 0x16e684
+/* [R 16] Pause state for physical queues 63-48 */
+#define QM_REG_PAUSESTATE3 0x16e688
+/* [R 16] Pause state for physical queues 79-64 */
+#define QM_REG_PAUSESTATE4 0x16e68c
+/* [R 16] Pause state for physical queues 95-80 */
+#define QM_REG_PAUSESTATE5 0x16e690
+/* [R 16] Pause state for physical queues 111-96 */
+#define QM_REG_PAUSESTATE6 0x16e694
+/* [R 16] Pause state for physical queues 127-112 */
+#define QM_REG_PAUSESTATE7 0x16e698
+/* [RW 2] The PCI attributes field used in the PCI request. */
+#define QM_REG_PCIREQAT 0x168054
+#define QM_REG_PF_EN 0x16e70c
+/* [R 24] The number of tasks stored in the QM for the PF. only even
+ * functions are valid in E2 (odd I registers will be hard wired to 0) */
+#define QM_REG_PF_USG_CNT_0 0x16e040
+/* [R 16] NOT USED */
+#define QM_REG_PORT0BYTECRD 0x168300
+/* [R 16] The byte credit of port 1 */
+#define QM_REG_PORT1BYTECRD 0x168304
+/* [RW 3] pci function number of queues 15-0 */
+#define QM_REG_PQ2PCIFUNC_0 0x16e6bc
+#define QM_REG_PQ2PCIFUNC_1 0x16e6c0
+#define QM_REG_PQ2PCIFUNC_2 0x16e6c4
+#define QM_REG_PQ2PCIFUNC_3 0x16e6c8
+#define QM_REG_PQ2PCIFUNC_4 0x16e6cc
+#define QM_REG_PQ2PCIFUNC_5 0x16e6d0
+#define QM_REG_PQ2PCIFUNC_6 0x16e6d4
+#define QM_REG_PQ2PCIFUNC_7 0x16e6d8
+/* [WB 54] Pointer Table Memory for queues 63-0; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+#define QM_REG_PTRTBL 0x168a00
+/* [WB 54] Pointer Table Memory for queues 127-64; The mapping is as follow:
+ ptrtbl[53:30] read pointer; ptrtbl[29:6] write pointer; ptrtbl[5:4] read
+ bank0; ptrtbl[3:2] read bank 1; ptrtbl[1:0] write bank; */
+#define QM_REG_PTRTBL_EXT_A 0x16e200
+/* [RW 2] Interrupt mask register #0 read/write */
+#define QM_REG_QM_INT_MASK 0x168444
+/* [R 2] Interrupt register #0 read */
+#define QM_REG_QM_INT_STS 0x168438
+/* [RW 12] Parity mask register #0 read/write */
+#define QM_REG_QM_PRTY_MASK 0x168454
+/* [R 12] Parity register #0 read */
+#define QM_REG_QM_PRTY_STS 0x168448
+/* [RC 12] Parity register #0 read clear */
+#define QM_REG_QM_PRTY_STS_CLR 0x16844c
+/* [R 32] Current queues in pipeline: Queues from 32 to 63 */
+#define QM_REG_QSTATUS_HIGH 0x16802c
+/* [R 32] Current queues in pipeline: Queues from 96 to 127 */
+#define QM_REG_QSTATUS_HIGH_EXT_A 0x16e408
+/* [R 32] Current queues in pipeline: Queues from 0 to 31 */
+#define QM_REG_QSTATUS_LOW 0x168028
+/* [R 32] Current queues in pipeline: Queues from 64 to 95 */
+#define QM_REG_QSTATUS_LOW_EXT_A 0x16e404
+/* [R 24] The number of tasks queued for each queue; queues 63-0 */
+#define QM_REG_QTASKCTR_0 0x168308
+/* [R 24] The number of tasks queued for each queue; queues 127-64 */
+#define QM_REG_QTASKCTR_EXT_A_0 0x16e584
+/* [RW 4] Queue tied to VOQ */
+#define QM_REG_QVOQIDX_0 0x1680f4
+#define QM_REG_QVOQIDX_10 0x16811c
+#define QM_REG_QVOQIDX_100 0x16e49c
+#define QM_REG_QVOQIDX_101 0x16e4a0
+#define QM_REG_QVOQIDX_102 0x16e4a4
+#define QM_REG_QVOQIDX_103 0x16e4a8
+#define QM_REG_QVOQIDX_104 0x16e4ac
+#define QM_REG_QVOQIDX_105 0x16e4b0
+#define QM_REG_QVOQIDX_106 0x16e4b4
+#define QM_REG_QVOQIDX_107 0x16e4b8
+#define QM_REG_QVOQIDX_108 0x16e4bc
+#define QM_REG_QVOQIDX_109 0x16e4c0
+#define QM_REG_QVOQIDX_11 0x168120
+#define QM_REG_QVOQIDX_110 0x16e4c4
+#define QM_REG_QVOQIDX_111 0x16e4c8
+#define QM_REG_QVOQIDX_112 0x16e4cc
+#define QM_REG_QVOQIDX_113 0x16e4d0
+#define QM_REG_QVOQIDX_114 0x16e4d4
+#define QM_REG_QVOQIDX_115 0x16e4d8
+#define QM_REG_QVOQIDX_116 0x16e4dc
+#define QM_REG_QVOQIDX_117 0x16e4e0
+#define QM_REG_QVOQIDX_118 0x16e4e4
+#define QM_REG_QVOQIDX_119 0x16e4e8
+#define QM_REG_QVOQIDX_12 0x168124
+#define QM_REG_QVOQIDX_120 0x16e4ec
+#define QM_REG_QVOQIDX_121 0x16e4f0
+#define QM_REG_QVOQIDX_122 0x16e4f4
+#define QM_REG_QVOQIDX_123 0x16e4f8
+#define QM_REG_QVOQIDX_124 0x16e4fc
+#define QM_REG_QVOQIDX_125 0x16e500
+#define QM_REG_QVOQIDX_126 0x16e504
+#define QM_REG_QVOQIDX_127 0x16e508
+#define QM_REG_QVOQIDX_13 0x168128
+#define QM_REG_QVOQIDX_14 0x16812c
+#define QM_REG_QVOQIDX_15 0x168130
+#define QM_REG_QVOQIDX_16 0x168134
+#define QM_REG_QVOQIDX_17 0x168138
+#define QM_REG_QVOQIDX_21 0x168148
+#define QM_REG_QVOQIDX_22 0x16814c
+#define QM_REG_QVOQIDX_23 0x168150
+#define QM_REG_QVOQIDX_24 0x168154
+#define QM_REG_QVOQIDX_25 0x168158
+#define QM_REG_QVOQIDX_26 0x16815c
+#define QM_REG_QVOQIDX_27 0x168160
+#define QM_REG_QVOQIDX_28 0x168164
+#define QM_REG_QVOQIDX_29 0x168168
+#define QM_REG_QVOQIDX_30 0x16816c
+#define QM_REG_QVOQIDX_31 0x168170
+#define QM_REG_QVOQIDX_32 0x168174
+#define QM_REG_QVOQIDX_33 0x168178
+#define QM_REG_QVOQIDX_34 0x16817c
+#define QM_REG_QVOQIDX_35 0x168180
+#define QM_REG_QVOQIDX_36 0x168184
+#define QM_REG_QVOQIDX_37 0x168188
+#define QM_REG_QVOQIDX_38 0x16818c
+#define QM_REG_QVOQIDX_39 0x168190
+#define QM_REG_QVOQIDX_40 0x168194
+#define QM_REG_QVOQIDX_41 0x168198
+#define QM_REG_QVOQIDX_42 0x16819c
+#define QM_REG_QVOQIDX_43 0x1681a0
+#define QM_REG_QVOQIDX_44 0x1681a4
+#define QM_REG_QVOQIDX_45 0x1681a8
+#define QM_REG_QVOQIDX_46 0x1681ac
+#define QM_REG_QVOQIDX_47 0x1681b0
+#define QM_REG_QVOQIDX_48 0x1681b4
+#define QM_REG_QVOQIDX_49 0x1681b8
+#define QM_REG_QVOQIDX_5 0x168108
+#define QM_REG_QVOQIDX_50 0x1681bc
+#define QM_REG_QVOQIDX_51 0x1681c0
+#define QM_REG_QVOQIDX_52 0x1681c4
+#define QM_REG_QVOQIDX_53 0x1681c8
+#define QM_REG_QVOQIDX_54 0x1681cc
+#define QM_REG_QVOQIDX_55 0x1681d0
+#define QM_REG_QVOQIDX_56 0x1681d4
+#define QM_REG_QVOQIDX_57 0x1681d8
+#define QM_REG_QVOQIDX_58 0x1681dc
+#define QM_REG_QVOQIDX_59 0x1681e0
+#define QM_REG_QVOQIDX_6 0x16810c
+#define QM_REG_QVOQIDX_60 0x1681e4
+#define QM_REG_QVOQIDX_61 0x1681e8
+#define QM_REG_QVOQIDX_62 0x1681ec
+#define QM_REG_QVOQIDX_63 0x1681f0
+#define QM_REG_QVOQIDX_64 0x16e40c
+#define QM_REG_QVOQIDX_65 0x16e410
+#define QM_REG_QVOQIDX_69 0x16e420
+#define QM_REG_QVOQIDX_7 0x168110
+#define QM_REG_QVOQIDX_70 0x16e424
+#define QM_REG_QVOQIDX_71 0x16e428
+#define QM_REG_QVOQIDX_72 0x16e42c
+#define QM_REG_QVOQIDX_73 0x16e430
+#define QM_REG_QVOQIDX_74 0x16e434
+#define QM_REG_QVOQIDX_75 0x16e438
+#define QM_REG_QVOQIDX_76 0x16e43c
+#define QM_REG_QVOQIDX_77 0x16e440
+#define QM_REG_QVOQIDX_78 0x16e444
+#define QM_REG_QVOQIDX_79 0x16e448
+#define QM_REG_QVOQIDX_8 0x168114
+#define QM_REG_QVOQIDX_80 0x16e44c
+#define QM_REG_QVOQIDX_81 0x16e450
+#define QM_REG_QVOQIDX_85 0x16e460
+#define QM_REG_QVOQIDX_86 0x16e464
+#define QM_REG_QVOQIDX_87 0x16e468
+#define QM_REG_QVOQIDX_88 0x16e46c
+#define QM_REG_QVOQIDX_89 0x16e470
+#define QM_REG_QVOQIDX_9 0x168118
+#define QM_REG_QVOQIDX_90 0x16e474
+#define QM_REG_QVOQIDX_91 0x16e478
+#define QM_REG_QVOQIDX_92 0x16e47c
+#define QM_REG_QVOQIDX_93 0x16e480
+#define QM_REG_QVOQIDX_94 0x16e484
+#define QM_REG_QVOQIDX_95 0x16e488
+#define QM_REG_QVOQIDX_96 0x16e48c
+#define QM_REG_QVOQIDX_97 0x16e490
+#define QM_REG_QVOQIDX_98 0x16e494
+#define QM_REG_QVOQIDX_99 0x16e498
+/* [RW 1] Initialization bit command */
+#define QM_REG_SOFT_RESET 0x168428
+/* [RW 8] The credit cost per every task in the QM. A value per each VOQ */
+#define QM_REG_TASKCRDCOST_0 0x16809c
+#define QM_REG_TASKCRDCOST_1 0x1680a0
+#define QM_REG_TASKCRDCOST_2 0x1680a4
+#define QM_REG_TASKCRDCOST_4 0x1680ac
+#define QM_REG_TASKCRDCOST_5 0x1680b0
+/* [R 6] Keep the fill level of the fifo from write client 3 */
+#define QM_REG_TQM_WRC_FIFOLVL 0x168010
+/* [R 6] Keep the fill level of the fifo from write client 2 */
+#define QM_REG_UQM_WRC_FIFOLVL 0x168008
+/* [RC 32] Credit update error register */
+#define QM_REG_VOQCRDERRREG 0x168408
+/* [R 16] The credit value for each VOQ */
+#define QM_REG_VOQCREDIT_0 0x1682d0
+#define QM_REG_VOQCREDIT_1 0x1682d4
+#define QM_REG_VOQCREDIT_4 0x1682e0
+/* [RW 16] The credit value that if above the QM is considered almost full */
+#define QM_REG_VOQCREDITAFULLTHR 0x168090
+/* [RW 16] The init and maximum credit for each VoQ */
+#define QM_REG_VOQINITCREDIT_0 0x168060
+#define QM_REG_VOQINITCREDIT_1 0x168064
+#define QM_REG_VOQINITCREDIT_2 0x168068
+#define QM_REG_VOQINITCREDIT_4 0x168070
+#define QM_REG_VOQINITCREDIT_5 0x168074
+/* [RW 1] The port of which VOQ belongs */
+#define QM_REG_VOQPORT_0 0x1682a0
+#define QM_REG_VOQPORT_1 0x1682a4
+#define QM_REG_VOQPORT_2 0x1682a8
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_0_LSB 0x168240
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_0_LSB_EXT_A 0x16e524
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_0_MSB 0x168244
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_0_MSB_EXT_A 0x16e528
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_10_LSB 0x168290
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_10_LSB_EXT_A 0x16e574
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_10_MSB 0x168294
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_10_MSB_EXT_A 0x16e578
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_11_LSB 0x168298
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_11_LSB_EXT_A 0x16e57c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_11_MSB 0x16829c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_11_MSB_EXT_A 0x16e580
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_1_LSB 0x168248
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_1_LSB_EXT_A 0x16e52c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_1_MSB 0x16824c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_1_MSB_EXT_A 0x16e530
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_2_LSB 0x168250
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_2_LSB_EXT_A 0x16e534
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_2_MSB 0x168254
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_2_MSB_EXT_A 0x16e538
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_3_LSB 0x168258
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_3_LSB_EXT_A 0x16e53c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_3_MSB_EXT_A 0x16e540
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_4_LSB 0x168260
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_4_LSB_EXT_A 0x16e544
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_4_MSB 0x168264
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_4_MSB_EXT_A 0x16e548
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_5_LSB 0x168268
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_5_LSB_EXT_A 0x16e54c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_5_MSB 0x16826c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_5_MSB_EXT_A 0x16e550
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_6_LSB 0x168270
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_6_LSB_EXT_A 0x16e554
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_6_MSB 0x168274
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_6_MSB_EXT_A 0x16e558
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_7_LSB 0x168278
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_7_LSB_EXT_A 0x16e55c
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_7_MSB 0x16827c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_7_MSB_EXT_A 0x16e560
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_8_LSB 0x168280
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_8_LSB_EXT_A 0x16e564
+/* [RW 32] The physical queue number associated with each VOQ; queues 63-32 */
+#define QM_REG_VOQQMASK_8_MSB 0x168284
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_8_MSB_EXT_A 0x16e568
+/* [RW 32] The physical queue number associated with each VOQ; queues 31-0 */
+#define QM_REG_VOQQMASK_9_LSB 0x168288
+/* [RW 32] The physical queue number associated with each VOQ; queues 95-64 */
+#define QM_REG_VOQQMASK_9_LSB_EXT_A 0x16e56c
+/* [RW 32] The physical queue number associated with each VOQ; queues 127-96 */
+#define QM_REG_VOQQMASK_9_MSB_EXT_A 0x16e570
+/* [RW 32] Wrr weights */
+#define QM_REG_WRRWEIGHTS_0 0x16880c
+#define QM_REG_WRRWEIGHTS_1 0x168810
+#define QM_REG_WRRWEIGHTS_10 0x168814
+#define QM_REG_WRRWEIGHTS_11 0x168818
+#define QM_REG_WRRWEIGHTS_12 0x16881c
+#define QM_REG_WRRWEIGHTS_13 0x168820
+#define QM_REG_WRRWEIGHTS_14 0x168824
+#define QM_REG_WRRWEIGHTS_15 0x168828
+#define QM_REG_WRRWEIGHTS_16 0x16e000
+#define QM_REG_WRRWEIGHTS_17 0x16e004
+#define QM_REG_WRRWEIGHTS_18 0x16e008
+#define QM_REG_WRRWEIGHTS_19 0x16e00c
+#define QM_REG_WRRWEIGHTS_2 0x16882c
+#define QM_REG_WRRWEIGHTS_20 0x16e010
+#define QM_REG_WRRWEIGHTS_21 0x16e014
+#define QM_REG_WRRWEIGHTS_22 0x16e018
+#define QM_REG_WRRWEIGHTS_23 0x16e01c
+#define QM_REG_WRRWEIGHTS_24 0x16e020
+#define QM_REG_WRRWEIGHTS_25 0x16e024
+#define QM_REG_WRRWEIGHTS_26 0x16e028
+#define QM_REG_WRRWEIGHTS_27 0x16e02c
+#define QM_REG_WRRWEIGHTS_28 0x16e030
+#define QM_REG_WRRWEIGHTS_29 0x16e034
+#define QM_REG_WRRWEIGHTS_3 0x168830
+#define QM_REG_WRRWEIGHTS_30 0x16e038
+#define QM_REG_WRRWEIGHTS_31 0x16e03c
+#define QM_REG_WRRWEIGHTS_4 0x168834
+#define QM_REG_WRRWEIGHTS_5 0x168838
+#define QM_REG_WRRWEIGHTS_6 0x16883c
+#define QM_REG_WRRWEIGHTS_7 0x168840
+#define QM_REG_WRRWEIGHTS_8 0x168844
+#define QM_REG_WRRWEIGHTS_9 0x168848
+/* [R 6] Keep the fill level of the fifo from write client 1 */
+#define QM_REG_XQM_WRC_FIFOLVL 0x168000
+/* [W 1] reset to parity interrupt */
+#define SEM_FAST_REG_PARITY_RST 0x18840
+#define SRC_REG_COUNTFREE0 0x40500
+/* [RW 1] If clr the searcher is compatible to E1 A0 - support only two
+ ports. If set the searcher support 8 functions. */
+#define SRC_REG_E1HMF_ENABLE 0x404cc
+#define SRC_REG_FIRSTFREE0 0x40510
+#define SRC_REG_KEYRSS0_0 0x40408
+#define SRC_REG_KEYRSS0_7 0x40424
+#define SRC_REG_KEYRSS1_9 0x40454
+#define SRC_REG_KEYSEARCH_0 0x40458
+#define SRC_REG_KEYSEARCH_1 0x4045c
+#define SRC_REG_KEYSEARCH_2 0x40460
+#define SRC_REG_KEYSEARCH_3 0x40464
+#define SRC_REG_KEYSEARCH_4 0x40468
+#define SRC_REG_KEYSEARCH_5 0x4046c
+#define SRC_REG_KEYSEARCH_6 0x40470
+#define SRC_REG_KEYSEARCH_7 0x40474
+#define SRC_REG_KEYSEARCH_8 0x40478
+#define SRC_REG_KEYSEARCH_9 0x4047c
+#define SRC_REG_LASTFREE0 0x40530
+#define SRC_REG_NUMBER_HASH_BITS0 0x40400
+/* [RW 1] Reset internal state machines. */
+#define SRC_REG_SOFT_RST 0x4049c
+/* [R 3] Interrupt register #0 read */
+#define SRC_REG_SRC_INT_STS 0x404ac
+/* [RW 3] Parity mask register #0 read/write */
+#define SRC_REG_SRC_PRTY_MASK 0x404c8
+/* [R 3] Parity register #0 read */
+#define SRC_REG_SRC_PRTY_STS 0x404bc
+/* [RC 3] Parity register #0 read clear */
+#define SRC_REG_SRC_PRTY_STS_CLR 0x404c0
+/* [R 4] Used to read the value of the XX protection CAM occupancy counter. */
+#define TCM_REG_CAM_OCCUP 0x5017c
+/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define TCM_REG_CDU_AG_RD_IFEN 0x50034
+/* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input
+ are disregarded; all other signals are treated as usual; if 1 - normal
+ activity. */
+#define TCM_REG_CDU_AG_WR_IFEN 0x50030
+/* [RW 1] CDU STORM read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define TCM_REG_CDU_SM_RD_IFEN 0x5003c
+/* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid
+ input is disregarded; all other signals are treated as usual; if 1 -
+ normal activity. */
+#define TCM_REG_CDU_SM_WR_IFEN 0x50038
+/* [RW 4] CFC output initial credit. Max credit available - 15.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 1 at start-up. */
+#define TCM_REG_CFC_INIT_CRD 0x50204
+/* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_CP_WEIGHT 0x500c0
+/* [RW 1] Input csem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define TCM_REG_CSEM_IFEN 0x5002c
+/* [RC 1] Message length mismatch (relative to last indication) at the In#9
+ interface. */
+#define TCM_REG_CSEM_LENGTH_MIS 0x50174
+/* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_CSEM_WEIGHT 0x500bc
+/* [RW 8] The Event ID in case of ErrorFlg is set in the input message. */
+#define TCM_REG_ERR_EVNT_ID 0x500a0
+/* [RW 28] The CM erroneous header for QM and Timers formatting. */
+#define TCM_REG_ERR_TCM_HDR 0x5009c
+/* [RW 8] The Event ID for Timers expiration. */
+#define TCM_REG_EXPR_EVNT_ID 0x500a4
+/* [RW 8] FIC0 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define TCM_REG_FIC0_INIT_CRD 0x5020c
+/* [RW 8] FIC1 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define TCM_REG_FIC1_INIT_CRD 0x50210
+/* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1
+ - strict priority defined by ~tcm_registers_gr_ag_pr.gr_ag_pr;
+ ~tcm_registers_gr_ld0_pr.gr_ld0_pr and
+ ~tcm_registers_gr_ld1_pr.gr_ld1_pr. */
+#define TCM_REG_GR_ARB_TYPE 0x50114
+/* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Store channel is the
+ compliment of the other 3 groups. */
+#define TCM_REG_GR_LD0_PR 0x5011c
+/* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Store channel is the
+ compliment of the other 3 groups. */
+#define TCM_REG_GR_LD1_PR 0x50120
+/* [RW 4] The number of double REG-pairs; loaded from the STORM context and
+ sent to STORM; for a specific connection type. The double REG-pairs are
+ used to align to STORM context row size of 128 bits. The offset of these
+ data in the STORM context is always 0. Index _i stands for the connection
+ type (one of 16). */
+#define TCM_REG_N_SM_CTX_LD_0 0x50050
+#define TCM_REG_N_SM_CTX_LD_1 0x50054
+#define TCM_REG_N_SM_CTX_LD_2 0x50058
+#define TCM_REG_N_SM_CTX_LD_3 0x5005c
+#define TCM_REG_N_SM_CTX_LD_4 0x50060
+#define TCM_REG_N_SM_CTX_LD_5 0x50064
+/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_PBF_IFEN 0x50024
+/* [RC 1] Message length mismatch (relative to last indication) at the In#7
+ interface. */
+#define TCM_REG_PBF_LENGTH_MIS 0x5016c
+/* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_PBF_WEIGHT 0x500b4
+#define TCM_REG_PHYS_QNUM0_0 0x500e0
+#define TCM_REG_PHYS_QNUM0_1 0x500e4
+#define TCM_REG_PHYS_QNUM1_0 0x500e8
+#define TCM_REG_PHYS_QNUM1_1 0x500ec
+#define TCM_REG_PHYS_QNUM2_0 0x500f0
+#define TCM_REG_PHYS_QNUM2_1 0x500f4
+#define TCM_REG_PHYS_QNUM3_0 0x500f8
+#define TCM_REG_PHYS_QNUM3_1 0x500fc
+/* [RW 1] Input prs Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_PRS_IFEN 0x50020
+/* [RC 1] Message length mismatch (relative to last indication) at the In#6
+ interface. */
+#define TCM_REG_PRS_LENGTH_MIS 0x50168
+/* [RW 3] The weight of the input prs in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_PRS_WEIGHT 0x500b0
+/* [RW 8] The Event ID for Timers formatting in case of stop done. */
+#define TCM_REG_STOP_EVNT_ID 0x500a8
+/* [RC 1] Message length mismatch (relative to last indication) at the STORM
+ interface. */
+#define TCM_REG_STORM_LENGTH_MIS 0x50160
+/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define TCM_REG_STORM_TCM_IFEN 0x50010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_STORM_WEIGHT 0x500ac
+/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TCM_CFC_IFEN 0x50040
+/* [RW 11] Interrupt mask register #0 read/write */
+#define TCM_REG_TCM_INT_MASK 0x501dc
+/* [R 11] Interrupt register #0 read */
+#define TCM_REG_TCM_INT_STS 0x501d0
+/* [RW 27] Parity mask register #0 read/write */
+#define TCM_REG_TCM_PRTY_MASK 0x501ec
+/* [R 27] Parity register #0 read */
+#define TCM_REG_TCM_PRTY_STS 0x501e0
+/* [RC 27] Parity register #0 read clear */
+#define TCM_REG_TCM_PRTY_STS_CLR 0x501e4
+/* [RW 3] The size of AG context region 0 in REG-pairs. Designates the MS
+ REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
+ Is used to determine the number of the AG context REG-pairs written back;
+ when the input message Reg1WbFlg isn't set. */
+#define TCM_REG_TCM_REG0_SZ 0x500d8
+/* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TCM_STORM0_IFEN 0x50004
+/* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TCM_STORM1_IFEN 0x50008
+/* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TCM_TQM_IFEN 0x5000c
+/* [RW 1] If set the Q index; received from the QM is inserted to event ID. */
+#define TCM_REG_TCM_TQM_USE_Q 0x500d4
+/* [RW 28] The CM header for Timers expiration command. */
+#define TCM_REG_TM_TCM_HDR 0x50098
+/* [RW 1] Timers - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define TCM_REG_TM_TCM_IFEN 0x5001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TM_WEIGHT 0x500d0
+/* [RW 6] QM output initial credit. Max credit available - 32.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 32 at start-up. */
+#define TCM_REG_TQM_INIT_CRD 0x5021c
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_P_WEIGHT 0x500c8
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TQM_S_WEIGHT 0x500cc
+/* [RW 28] The CM header value for QM request (primary). */
+#define TCM_REG_TQM_TCM_HDR_P 0x50090
+/* [RW 28] The CM header value for QM request (secondary). */
+#define TCM_REG_TQM_TCM_HDR_S 0x50094
+/* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TQM_TCM_IFEN 0x50014
+/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define TCM_REG_TSDM_IFEN 0x50018
+/* [RC 1] Message length mismatch (relative to last indication) at the SDM
+ interface. */
+#define TCM_REG_TSDM_LENGTH_MIS 0x50164
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_TSDM_WEIGHT 0x500c4
+/* [RW 1] Input usem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define TCM_REG_USEM_IFEN 0x50028
+/* [RC 1] Message length mismatch (relative to last indication) at the In#8
+ interface. */
+#define TCM_REG_USEM_LENGTH_MIS 0x50170
+/* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define TCM_REG_USEM_WEIGHT 0x500b8
+/* [RW 21] Indirect access to the descriptor table of the XX protection
+ mechanism. The fields are: [5:0] - length of the message; 15:6] - message
+ pointer; 20:16] - next pointer. */
+#define TCM_REG_XX_DESCR_TABLE 0x50280
+#define TCM_REG_XX_DESCR_TABLE_SIZE 29
+/* [R 6] Use to read the value of XX protection Free counter. */
+#define TCM_REG_XX_FREE 0x50178
+/* [RW 6] Initial value for the credit counter; responsible for fulfilling
+ of the Input Stage XX protection buffer by the XX protection pending
+ messages. Max credit available - 127.Write writes the initial credit
+ value; read returns the current value of the credit counter. Must be
+ initialized to 19 at start-up. */
+#define TCM_REG_XX_INIT_CRD 0x50220
+/* [RW 6] Maximum link list size (messages locked) per connection in the XX
+ protection. */
+#define TCM_REG_XX_MAX_LL_SZ 0x50044
+/* [RW 6] The maximum number of pending messages; which may be stored in XX
+ protection. ~tcm_registers_xx_free.xx_free is read on read. */
+#define TCM_REG_XX_MSG_NUM 0x50224
+/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
+#define TCM_REG_XX_OVFL_EVNT_ID 0x50048
+/* [RW 16] Indirect access to the XX table of the XX protection mechanism.
+ The fields are:[4:0] - tail pointer; [10:5] - Link List size; 15:11] -
+ header pointer. */
+#define TCM_REG_XX_TABLE 0x50240
+/* [RW 4] Load value for cfc ac credit cnt. */
+#define TM_REG_CFC_AC_CRDCNT_VAL 0x164208
+/* [RW 4] Load value for cfc cld credit cnt. */
+#define TM_REG_CFC_CLD_CRDCNT_VAL 0x164210
+/* [RW 8] Client0 context region. */
+#define TM_REG_CL0_CONT_REGION 0x164030
+/* [RW 8] Client1 context region. */
+#define TM_REG_CL1_CONT_REGION 0x164034
+/* [RW 8] Client2 context region. */
+#define TM_REG_CL2_CONT_REGION 0x164038
+/* [RW 2] Client in High priority client number. */
+#define TM_REG_CLIN_PRIOR0_CLIENT 0x164024
+/* [RW 4] Load value for clout0 cred cnt. */
+#define TM_REG_CLOUT_CRDCNT0_VAL 0x164220
+/* [RW 4] Load value for clout1 cred cnt. */
+#define TM_REG_CLOUT_CRDCNT1_VAL 0x164228
+/* [RW 4] Load value for clout2 cred cnt. */
+#define TM_REG_CLOUT_CRDCNT2_VAL 0x164230
+/* [RW 1] Enable client0 input. */
+#define TM_REG_EN_CL0_INPUT 0x164008
+/* [RW 1] Enable client1 input. */
+#define TM_REG_EN_CL1_INPUT 0x16400c
+/* [RW 1] Enable client2 input. */
+#define TM_REG_EN_CL2_INPUT 0x164010
+#define TM_REG_EN_LINEAR0_TIMER 0x164014
+/* [RW 1] Enable real time counter. */
+#define TM_REG_EN_REAL_TIME_CNT 0x1640d8
+/* [RW 1] Enable for Timers state machines. */
+#define TM_REG_EN_TIMERS 0x164000
+/* [RW 4] Load value for expiration credit cnt. CFC max number of
+ outstanding load requests for timers (expiration) context loading. */
+#define TM_REG_EXP_CRDCNT_VAL 0x164238
+/* [RW 32] Linear0 logic address. */
+#define TM_REG_LIN0_LOGIC_ADDR 0x164240
+/* [RW 18] Linear0 Max active cid (in banks of 32 entries). */
+#define TM_REG_LIN0_MAX_ACTIVE_CID 0x164048
+/* [ST 16] Linear0 Number of scans counter. */
+#define TM_REG_LIN0_NUM_SCANS 0x1640a0
+/* [WB 64] Linear0 phy address. */
+#define TM_REG_LIN0_PHY_ADDR 0x164270
+/* [RW 1] Linear0 physical address valid. */
+#define TM_REG_LIN0_PHY_ADDR_VALID 0x164248
+#define TM_REG_LIN0_SCAN_ON 0x1640d0
+/* [RW 24] Linear0 array scan timeout. */
+#define TM_REG_LIN0_SCAN_TIME 0x16403c
+#define TM_REG_LIN0_VNIC_UC 0x164128
+/* [RW 32] Linear1 logic address. */
+#define TM_REG_LIN1_LOGIC_ADDR 0x164250
+/* [WB 64] Linear1 phy address. */
+#define TM_REG_LIN1_PHY_ADDR 0x164280
+/* [RW 1] Linear1 physical address valid. */
+#define TM_REG_LIN1_PHY_ADDR_VALID 0x164258
+/* [RW 6] Linear timer set_clear fifo threshold. */
+#define TM_REG_LIN_SETCLR_FIFO_ALFULL_THR 0x164070
+/* [RW 2] Load value for pci arbiter credit cnt. */
+#define TM_REG_PCIARB_CRDCNT_VAL 0x164260
+/* [RW 20] The amount of hardware cycles for each timer tick. */
+#define TM_REG_TIMER_TICK_SIZE 0x16401c
+/* [RW 8] Timers Context region. */
+#define TM_REG_TM_CONTEXT_REGION 0x164044
+/* [RW 1] Interrupt mask register #0 read/write */
+#define TM_REG_TM_INT_MASK 0x1640fc
+/* [R 1] Interrupt register #0 read */
+#define TM_REG_TM_INT_STS 0x1640f0
+/* [RW 7] Parity mask register #0 read/write */
+#define TM_REG_TM_PRTY_MASK 0x16410c
+/* [R 7] Parity register #0 read */
+#define TM_REG_TM_PRTY_STS 0x164100
+/* [RC 7] Parity register #0 read clear */
+#define TM_REG_TM_PRTY_STS_CLR 0x164104
+/* [RW 8] The event id for aggregated interrupt 0 */
+#define TSDM_REG_AGG_INT_EVENT_0 0x42038
+#define TSDM_REG_AGG_INT_EVENT_1 0x4203c
+#define TSDM_REG_AGG_INT_EVENT_2 0x42040
+#define TSDM_REG_AGG_INT_EVENT_3 0x42044
+#define TSDM_REG_AGG_INT_EVENT_4 0x42048
+/* [RW 1] The T bit for aggregated interrupt 0 */
+#define TSDM_REG_AGG_INT_T_0 0x420b8
+#define TSDM_REG_AGG_INT_T_1 0x420bc
+/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
+#define TSDM_REG_CFC_RSP_START_ADDR 0x42008
+/* [RW 16] The maximum value of the completion counter #0 */
+#define TSDM_REG_CMP_COUNTER_MAX0 0x4201c
+/* [RW 16] The maximum value of the completion counter #1 */
+#define TSDM_REG_CMP_COUNTER_MAX1 0x42020
+/* [RW 16] The maximum value of the completion counter #2 */
+#define TSDM_REG_CMP_COUNTER_MAX2 0x42024
+/* [RW 16] The maximum value of the completion counter #3 */
+#define TSDM_REG_CMP_COUNTER_MAX3 0x42028
+/* [RW 13] The start address in the internal RAM for the completion
+ counters. */
+#define TSDM_REG_CMP_COUNTER_START_ADDR 0x4200c
+#define TSDM_REG_ENABLE_IN1 0x42238
+#define TSDM_REG_ENABLE_IN2 0x4223c
+#define TSDM_REG_ENABLE_OUT1 0x42240
+#define TSDM_REG_ENABLE_OUT2 0x42244
+/* [RW 4] The initial number of messages that can be sent to the pxp control
+ interface without receiving any ACK. */
+#define TSDM_REG_INIT_CREDIT_PXP_CTRL 0x424bc
+/* [ST 32] The number of ACK after placement messages received */
+#define TSDM_REG_NUM_OF_ACK_AFTER_PLACE 0x4227c
+/* [ST 32] The number of packet end messages received from the parser */
+#define TSDM_REG_NUM_OF_PKT_END_MSG 0x42274
+/* [ST 32] The number of requests received from the pxp async if */
+#define TSDM_REG_NUM_OF_PXP_ASYNC_REQ 0x42278
+/* [ST 32] The number of commands received in queue 0 */
+#define TSDM_REG_NUM_OF_Q0_CMD 0x42248
+/* [ST 32] The number of commands received in queue 10 */
+#define TSDM_REG_NUM_OF_Q10_CMD 0x4226c
+/* [ST 32] The number of commands received in queue 11 */
+#define TSDM_REG_NUM_OF_Q11_CMD 0x42270
+/* [ST 32] The number of commands received in queue 1 */
+#define TSDM_REG_NUM_OF_Q1_CMD 0x4224c
+/* [ST 32] The number of commands received in queue 3 */
+#define TSDM_REG_NUM_OF_Q3_CMD 0x42250
+/* [ST 32] The number of commands received in queue 4 */
+#define TSDM_REG_NUM_OF_Q4_CMD 0x42254
+/* [ST 32] The number of commands received in queue 5 */
+#define TSDM_REG_NUM_OF_Q5_CMD 0x42258
+/* [ST 32] The number of commands received in queue 6 */
+#define TSDM_REG_NUM_OF_Q6_CMD 0x4225c
+/* [ST 32] The number of commands received in queue 7 */
+#define TSDM_REG_NUM_OF_Q7_CMD 0x42260
+/* [ST 32] The number of commands received in queue 8 */
+#define TSDM_REG_NUM_OF_Q8_CMD 0x42264
+/* [ST 32] The number of commands received in queue 9 */
+#define TSDM_REG_NUM_OF_Q9_CMD 0x42268
+/* [RW 13] The start address in the internal RAM for the packet end message */
+#define TSDM_REG_PCK_END_MSG_START_ADDR 0x42014
+/* [RW 13] The start address in the internal RAM for queue counters */
+#define TSDM_REG_Q_COUNTER_START_ADDR 0x42010
+/* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */
+#define TSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0x42548
+/* [R 1] parser fifo empty in sdm_sync block */
+#define TSDM_REG_SYNC_PARSER_EMPTY 0x42550
+/* [R 1] parser serial fifo empty in sdm_sync block */
+#define TSDM_REG_SYNC_SYNC_EMPTY 0x42558
+/* [RW 32] Tick for timer counter. Applicable only when
+ ~tsdm_registers_timer_tick_enable.timer_tick_enable =1 */
+#define TSDM_REG_TIMER_TICK 0x42000
+/* [RW 32] Interrupt mask register #0 read/write */
+#define TSDM_REG_TSDM_INT_MASK_0 0x4229c
+#define TSDM_REG_TSDM_INT_MASK_1 0x422ac
+/* [R 32] Interrupt register #0 read */
+#define TSDM_REG_TSDM_INT_STS_0 0x42290
+#define TSDM_REG_TSDM_INT_STS_1 0x422a0
+/* [RW 11] Parity mask register #0 read/write */
+#define TSDM_REG_TSDM_PRTY_MASK 0x422bc
+/* [R 11] Parity register #0 read */
+#define TSDM_REG_TSDM_PRTY_STS 0x422b0
+/* [RC 11] Parity register #0 read clear */
+#define TSDM_REG_TSDM_PRTY_STS_CLR 0x422b4
+/* [RW 5] The number of time_slots in the arbitration cycle */
+#define TSEM_REG_ARB_CYCLE_SIZE 0x180034
+/* [RW 3] The source that is associated with arbitration element 0. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2 */
+#define TSEM_REG_ARB_ELEMENT0 0x180020
+/* [RW 3] The source that is associated with arbitration element 1. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~tsem_registers_arb_element0.arb_element0 */
+#define TSEM_REG_ARB_ELEMENT1 0x180024
+/* [RW 3] The source that is associated with arbitration element 2. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~tsem_registers_arb_element0.arb_element0
+ and ~tsem_registers_arb_element1.arb_element1 */
+#define TSEM_REG_ARB_ELEMENT2 0x180028
+/* [RW 3] The source that is associated with arbitration element 3. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.Could
+ not be equal to register ~tsem_registers_arb_element0.arb_element0 and
+ ~tsem_registers_arb_element1.arb_element1 and
+ ~tsem_registers_arb_element2.arb_element2 */
+#define TSEM_REG_ARB_ELEMENT3 0x18002c
+/* [RW 3] The source that is associated with arbitration element 4. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~tsem_registers_arb_element0.arb_element0
+ and ~tsem_registers_arb_element1.arb_element1 and
+ ~tsem_registers_arb_element2.arb_element2 and
+ ~tsem_registers_arb_element3.arb_element3 */
+#define TSEM_REG_ARB_ELEMENT4 0x180030
+#define TSEM_REG_ENABLE_IN 0x1800a4
+#define TSEM_REG_ENABLE_OUT 0x1800a8
+/* [RW 32] This address space contains all registers and memories that are
+ placed in SEM_FAST block. The SEM_FAST registers are described in
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
+#define TSEM_REG_FAST_MEMORY 0x1a0000
+/* [RW 1] Disables input messages from FIC0 May be updated during run_time
+ by the microcode */
+#define TSEM_REG_FIC0_DISABLE 0x180224
+/* [RW 1] Disables input messages from FIC1 May be updated during run_time
+ by the microcode */
+#define TSEM_REG_FIC1_DISABLE 0x180234
+/* [RW 15] Interrupt table Read and write access to it is not possible in
+ the middle of the work */
+#define TSEM_REG_INT_TABLE 0x180400
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC0 */
+#define TSEM_REG_MSG_NUM_FIC0 0x180000
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC1 */
+#define TSEM_REG_MSG_NUM_FIC1 0x180004
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC0 */
+#define TSEM_REG_MSG_NUM_FOC0 0x180008
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC1 */
+#define TSEM_REG_MSG_NUM_FOC1 0x18000c
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC2 */
+#define TSEM_REG_MSG_NUM_FOC2 0x180010
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC3 */
+#define TSEM_REG_MSG_NUM_FOC3 0x180014
+/* [RW 1] Disables input messages from the passive buffer May be updated
+ during run_time by the microcode */
+#define TSEM_REG_PAS_DISABLE 0x18024c
+/* [WB 128] Debug only. Passive buffer memory */
+#define TSEM_REG_PASSIVE_BUFFER 0x181000
+/* [WB 46] pram memory. B45 is parity; b[44:0] - data. */
+#define TSEM_REG_PRAM 0x1c0000
+/* [R 8] Valid sleeping threads indication have bit per thread */
+#define TSEM_REG_SLEEP_THREADS_VALID 0x18026c
+/* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */
+#define TSEM_REG_SLOW_EXT_STORE_EMPTY 0x1802a0
+/* [RW 8] List of free threads . There is a bit per thread. */
+#define TSEM_REG_THREADS_LIST 0x1802e4
+/* [RC 32] Parity register #0 read clear */
+#define TSEM_REG_TSEM_PRTY_STS_CLR_0 0x180118
+#define TSEM_REG_TSEM_PRTY_STS_CLR_1 0x180128
+/* [RW 3] The arbitration scheme of time_slot 0 */
+#define TSEM_REG_TS_0_AS 0x180038
+/* [RW 3] The arbitration scheme of time_slot 10 */
+#define TSEM_REG_TS_10_AS 0x180060
+/* [RW 3] The arbitration scheme of time_slot 11 */
+#define TSEM_REG_TS_11_AS 0x180064
+/* [RW 3] The arbitration scheme of time_slot 12 */
+#define TSEM_REG_TS_12_AS 0x180068
+/* [RW 3] The arbitration scheme of time_slot 13 */
+#define TSEM_REG_TS_13_AS 0x18006c
+/* [RW 3] The arbitration scheme of time_slot 14 */
+#define TSEM_REG_TS_14_AS 0x180070
+/* [RW 3] The arbitration scheme of time_slot 15 */
+#define TSEM_REG_TS_15_AS 0x180074
+/* [RW 3] The arbitration scheme of time_slot 16 */
+#define TSEM_REG_TS_16_AS 0x180078
+/* [RW 3] The arbitration scheme of time_slot 17 */
+#define TSEM_REG_TS_17_AS 0x18007c
+/* [RW 3] The arbitration scheme of time_slot 18 */
+#define TSEM_REG_TS_18_AS 0x180080
+/* [RW 3] The arbitration scheme of time_slot 1 */
+#define TSEM_REG_TS_1_AS 0x18003c
+/* [RW 3] The arbitration scheme of time_slot 2 */
+#define TSEM_REG_TS_2_AS 0x180040
+/* [RW 3] The arbitration scheme of time_slot 3 */
+#define TSEM_REG_TS_3_AS 0x180044
+/* [RW 3] The arbitration scheme of time_slot 4 */
+#define TSEM_REG_TS_4_AS 0x180048
+/* [RW 3] The arbitration scheme of time_slot 5 */
+#define TSEM_REG_TS_5_AS 0x18004c
+/* [RW 3] The arbitration scheme of time_slot 6 */
+#define TSEM_REG_TS_6_AS 0x180050
+/* [RW 3] The arbitration scheme of time_slot 7 */
+#define TSEM_REG_TS_7_AS 0x180054
+/* [RW 3] The arbitration scheme of time_slot 8 */
+#define TSEM_REG_TS_8_AS 0x180058
+/* [RW 3] The arbitration scheme of time_slot 9 */
+#define TSEM_REG_TS_9_AS 0x18005c
+/* [RW 32] Interrupt mask register #0 read/write */
+#define TSEM_REG_TSEM_INT_MASK_0 0x180100
+#define TSEM_REG_TSEM_INT_MASK_1 0x180110
+/* [R 32] Interrupt register #0 read */
+#define TSEM_REG_TSEM_INT_STS_0 0x1800f4
+#define TSEM_REG_TSEM_INT_STS_1 0x180104
+/* [RW 32] Parity mask register #0 read/write */
+#define TSEM_REG_TSEM_PRTY_MASK_0 0x180120
+#define TSEM_REG_TSEM_PRTY_MASK_1 0x180130
+/* [R 32] Parity register #0 read */
+#define TSEM_REG_TSEM_PRTY_STS_0 0x180114
+#define TSEM_REG_TSEM_PRTY_STS_1 0x180124
+/* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64
+ * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */
+#define TSEM_REG_VFPF_ERR_NUM 0x180380
+/* [RW 32] Indirect access to AG context with 32-bits granularity. The bits
+ * [10:8] of the address should be the offset within the accessed LCID
+ * context; the bits [7:0] are the accessed LCID.Example: to write to REG10
+ * LCID100. The RBC address should be 12'ha64. */
+#define UCM_REG_AG_CTX 0xe2000
+/* [R 5] Used to read the XX protection CAM occupancy counter. */
+#define UCM_REG_CAM_OCCUP 0xe0170
+/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define UCM_REG_CDU_AG_RD_IFEN 0xe0038
+/* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input
+ are disregarded; all other signals are treated as usual; if 1 - normal
+ activity. */
+#define UCM_REG_CDU_AG_WR_IFEN 0xe0034
+/* [RW 1] CDU STORM read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define UCM_REG_CDU_SM_RD_IFEN 0xe0040
+/* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid
+ input is disregarded; all other signals are treated as usual; if 1 -
+ normal activity. */
+#define UCM_REG_CDU_SM_WR_IFEN 0xe003c
+/* [RW 4] CFC output initial credit. Max credit available - 15.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 1 at start-up. */
+#define UCM_REG_CFC_INIT_CRD 0xe0204
+/* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_CP_WEIGHT 0xe00c4
+/* [RW 1] Input csem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_CSEM_IFEN 0xe0028
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the csem interface is detected. */
+#define UCM_REG_CSEM_LENGTH_MIS 0xe0160
+/* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_CSEM_WEIGHT 0xe00b8
+/* [RW 1] Input dorq Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_DORQ_IFEN 0xe0030
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the dorq interface is detected. */
+#define UCM_REG_DORQ_LENGTH_MIS 0xe0168
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_DORQ_WEIGHT 0xe00c0
+/* [RW 8] The Event ID in case ErrorFlg input message bit is set. */
+#define UCM_REG_ERR_EVNT_ID 0xe00a4
+/* [RW 28] The CM erroneous header for QM and Timers formatting. */
+#define UCM_REG_ERR_UCM_HDR 0xe00a0
+/* [RW 8] The Event ID for Timers expiration. */
+#define UCM_REG_EXPR_EVNT_ID 0xe00a8
+/* [RW 8] FIC0 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define UCM_REG_FIC0_INIT_CRD 0xe020c
+/* [RW 8] FIC1 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define UCM_REG_FIC1_INIT_CRD 0xe0210
+/* [RW 1] Arbitration between Input Arbiter groups: 0 - fair Round-Robin; 1
+ - strict priority defined by ~ucm_registers_gr_ag_pr.gr_ag_pr;
+ ~ucm_registers_gr_ld0_pr.gr_ld0_pr and
+ ~ucm_registers_gr_ld1_pr.gr_ld1_pr. */
+#define UCM_REG_GR_ARB_TYPE 0xe0144
+/* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Store channel group is
+ compliment to the others. */
+#define UCM_REG_GR_LD0_PR 0xe014c
+/* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Store channel group is
+ compliment to the others. */
+#define UCM_REG_GR_LD1_PR 0xe0150
+/* [RW 2] The queue index for invalidate counter flag decision. */
+#define UCM_REG_INV_CFLG_Q 0xe00e4
+/* [RW 5] The number of double REG-pairs; loaded from the STORM context and
+ sent to STORM; for a specific connection type. the double REG-pairs are
+ used in order to align to STORM context row size of 128 bits. The offset
+ of these data in the STORM context is always 0. Index _i stands for the
+ connection type (one of 16). */
+#define UCM_REG_N_SM_CTX_LD_0 0xe0054
+#define UCM_REG_N_SM_CTX_LD_1 0xe0058
+#define UCM_REG_N_SM_CTX_LD_2 0xe005c
+#define UCM_REG_N_SM_CTX_LD_3 0xe0060
+#define UCM_REG_N_SM_CTX_LD_4 0xe0064
+#define UCM_REG_N_SM_CTX_LD_5 0xe0068
+#define UCM_REG_PHYS_QNUM0_0 0xe0110
+#define UCM_REG_PHYS_QNUM0_1 0xe0114
+#define UCM_REG_PHYS_QNUM1_0 0xe0118
+#define UCM_REG_PHYS_QNUM1_1 0xe011c
+#define UCM_REG_PHYS_QNUM2_0 0xe0120
+#define UCM_REG_PHYS_QNUM2_1 0xe0124
+#define UCM_REG_PHYS_QNUM3_0 0xe0128
+#define UCM_REG_PHYS_QNUM3_1 0xe012c
+/* [RW 8] The Event ID for Timers formatting in case of stop done. */
+#define UCM_REG_STOP_EVNT_ID 0xe00ac
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the STORM interface is detected. */
+#define UCM_REG_STORM_LENGTH_MIS 0xe0154
+/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_STORM_UCM_IFEN 0xe0010
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_STORM_WEIGHT 0xe00b0
+/* [RW 4] Timers output initial credit. Max credit available - 15.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 4 at start-up. */
+#define UCM_REG_TM_INIT_CRD 0xe021c
+/* [RW 28] The CM header for Timers expiration command. */
+#define UCM_REG_TM_UCM_HDR 0xe009c
+/* [RW 1] Timers - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_TM_UCM_IFEN 0xe001c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_TM_WEIGHT 0xe00d4
+/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_TSEM_IFEN 0xe0024
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the tsem interface is detected. */
+#define UCM_REG_TSEM_LENGTH_MIS 0xe015c
+/* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_TSEM_WEIGHT 0xe00b4
+/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_UCM_CFC_IFEN 0xe0044
+/* [RW 11] Interrupt mask register #0 read/write */
+#define UCM_REG_UCM_INT_MASK 0xe01d4
+/* [R 11] Interrupt register #0 read */
+#define UCM_REG_UCM_INT_STS 0xe01c8
+/* [RW 27] Parity mask register #0 read/write */
+#define UCM_REG_UCM_PRTY_MASK 0xe01e4
+/* [R 27] Parity register #0 read */
+#define UCM_REG_UCM_PRTY_STS 0xe01d8
+/* [RC 27] Parity register #0 read clear */
+#define UCM_REG_UCM_PRTY_STS_CLR 0xe01dc
+/* [RW 2] The size of AG context region 0 in REG-pairs. Designates the MS
+ REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
+ Is used to determine the number of the AG context REG-pairs written back;
+ when the Reg1WbFlg isn't set. */
+#define UCM_REG_UCM_REG0_SZ 0xe00dc
+/* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_UCM_STORM0_IFEN 0xe0004
+/* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_UCM_STORM1_IFEN 0xe0008
+/* [RW 1] CM - Timers Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_UCM_TM_IFEN 0xe0020
+/* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_UCM_UQM_IFEN 0xe000c
+/* [RW 1] If set the Q index; received from the QM is inserted to event ID. */
+#define UCM_REG_UCM_UQM_USE_Q 0xe00d8
+/* [RW 6] QM output initial credit. Max credit available - 32.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 32 at start-up. */
+#define UCM_REG_UQM_INIT_CRD 0xe0220
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_UQM_P_WEIGHT 0xe00cc
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_UQM_S_WEIGHT 0xe00d0
+/* [RW 28] The CM header value for QM request (primary). */
+#define UCM_REG_UQM_UCM_HDR_P 0xe0094
+/* [RW 28] The CM header value for QM request (secondary). */
+#define UCM_REG_UQM_UCM_HDR_S 0xe0098
+/* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_UQM_UCM_IFEN 0xe0014
+/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define UCM_REG_USDM_IFEN 0xe0018
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the SDM interface is detected. */
+#define UCM_REG_USDM_LENGTH_MIS 0xe0158
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_USDM_WEIGHT 0xe00c8
+/* [RW 1] Input xsem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define UCM_REG_XSEM_IFEN 0xe002c
+/* [RC 1] Set when the message length mismatch (relative to last indication)
+ at the xsem interface isdetected. */
+#define UCM_REG_XSEM_LENGTH_MIS 0xe0164
+/* [RW 3] The weight of the input xsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define UCM_REG_XSEM_WEIGHT 0xe00bc
+/* [RW 20] Indirect access to the descriptor table of the XX protection
+ mechanism. The fields are:[5:0] - message length; 14:6] - message
+ pointer; 19:15] - next pointer. */
+#define UCM_REG_XX_DESCR_TABLE 0xe0280
+#define UCM_REG_XX_DESCR_TABLE_SIZE 27
+/* [R 6] Use to read the XX protection Free counter. */
+#define UCM_REG_XX_FREE 0xe016c
+/* [RW 6] Initial value for the credit counter; responsible for fulfilling
+ of the Input Stage XX protection buffer by the XX protection pending
+ messages. Write writes the initial credit value; read returns the current
+ value of the credit counter. Must be initialized to 12 at start-up. */
+#define UCM_REG_XX_INIT_CRD 0xe0224
+/* [RW 6] The maximum number of pending messages; which may be stored in XX
+ protection. ~ucm_registers_xx_free.xx_free read on read. */
+#define UCM_REG_XX_MSG_NUM 0xe0228
+/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
+#define UCM_REG_XX_OVFL_EVNT_ID 0xe004c
+/* [RW 16] Indirect access to the XX table of the XX protection mechanism.
+ The fields are: [4:0] - tail pointer; 10:5] - Link List size; 15:11] -
+ header pointer. */
+#define UCM_REG_XX_TABLE 0xe0300
+#define UMAC_COMMAND_CONFIG_REG_HD_ENA (0x1<<10)
+#define UMAC_COMMAND_CONFIG_REG_IGNORE_TX_PAUSE (0x1<<28)
+#define UMAC_COMMAND_CONFIG_REG_LOOP_ENA (0x1<<15)
+#define UMAC_COMMAND_CONFIG_REG_NO_LGTH_CHECK (0x1<<24)
+#define UMAC_COMMAND_CONFIG_REG_PAD_EN (0x1<<5)
+#define UMAC_COMMAND_CONFIG_REG_PAUSE_IGNORE (0x1<<8)
+#define UMAC_COMMAND_CONFIG_REG_PROMIS_EN (0x1<<4)
+#define UMAC_COMMAND_CONFIG_REG_RX_ENA (0x1<<1)
+#define UMAC_COMMAND_CONFIG_REG_SW_RESET (0x1<<13)
+#define UMAC_COMMAND_CONFIG_REG_TX_ENA (0x1<<0)
+#define UMAC_REG_COMMAND_CONFIG 0x8
+/* [RW 16] This is the duration for which MAC must wait to go back to ACTIVE
+ * state from LPI state when it receives packet for transmission. The
+ * decrement unit is 1 micro-second. */
+#define UMAC_REG_EEE_WAKE_TIMER 0x6c
+/* [RW 32] Register Bit 0 refers to Bit 16 of the MAC address; Bit 1 refers
+ * to bit 17 of the MAC address etc. */
+#define UMAC_REG_MAC_ADDR0 0xc
+/* [RW 16] Register Bit 0 refers to Bit 0 of the MAC address; Register Bit 1
+ * refers to Bit 1 of the MAC address etc. Bits 16 to 31 are reserved. */
+#define UMAC_REG_MAC_ADDR1 0x10
+/* [RW 14] Defines a 14-Bit maximum frame length used by the MAC receive
+ * logic to check frames. */
+#define UMAC_REG_MAXFR 0x14
+#define UMAC_REG_UMAC_EEE_CTRL 0x64
+#define UMAC_UMAC_EEE_CTRL_REG_EEE_EN (0x1<<3)
+/* [RW 8] The event id for aggregated interrupt 0 */
+#define USDM_REG_AGG_INT_EVENT_0 0xc4038
+#define USDM_REG_AGG_INT_EVENT_1 0xc403c
+#define USDM_REG_AGG_INT_EVENT_2 0xc4040
+#define USDM_REG_AGG_INT_EVENT_4 0xc4048
+#define USDM_REG_AGG_INT_EVENT_5 0xc404c
+#define USDM_REG_AGG_INT_EVENT_6 0xc4050
+/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
+ or auto-mask-mode (1) */
+#define USDM_REG_AGG_INT_MODE_0 0xc41b8
+#define USDM_REG_AGG_INT_MODE_1 0xc41bc
+#define USDM_REG_AGG_INT_MODE_4 0xc41c8
+#define USDM_REG_AGG_INT_MODE_5 0xc41cc
+#define USDM_REG_AGG_INT_MODE_6 0xc41d0
+/* [RW 1] The T bit for aggregated interrupt 5 */
+#define USDM_REG_AGG_INT_T_5 0xc40cc
+#define USDM_REG_AGG_INT_T_6 0xc40d0
+/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
+#define USDM_REG_CFC_RSP_START_ADDR 0xc4008
+/* [RW 16] The maximum value of the completion counter #0 */
+#define USDM_REG_CMP_COUNTER_MAX0 0xc401c
+/* [RW 16] The maximum value of the completion counter #1 */
+#define USDM_REG_CMP_COUNTER_MAX1 0xc4020
+/* [RW 16] The maximum value of the completion counter #2 */
+#define USDM_REG_CMP_COUNTER_MAX2 0xc4024
+/* [RW 16] The maximum value of the completion counter #3 */
+#define USDM_REG_CMP_COUNTER_MAX3 0xc4028
+/* [RW 13] The start address in the internal RAM for the completion
+ counters. */
+#define USDM_REG_CMP_COUNTER_START_ADDR 0xc400c
+#define USDM_REG_ENABLE_IN1 0xc4238
+#define USDM_REG_ENABLE_IN2 0xc423c
+#define USDM_REG_ENABLE_OUT1 0xc4240
+#define USDM_REG_ENABLE_OUT2 0xc4244
+/* [RW 4] The initial number of messages that can be sent to the pxp control
+ interface without receiving any ACK. */
+#define USDM_REG_INIT_CREDIT_PXP_CTRL 0xc44c0
+/* [ST 32] The number of ACK after placement messages received */
+#define USDM_REG_NUM_OF_ACK_AFTER_PLACE 0xc4280
+/* [ST 32] The number of packet end messages received from the parser */
+#define USDM_REG_NUM_OF_PKT_END_MSG 0xc4278
+/* [ST 32] The number of requests received from the pxp async if */
+#define USDM_REG_NUM_OF_PXP_ASYNC_REQ 0xc427c
+/* [ST 32] The number of commands received in queue 0 */
+#define USDM_REG_NUM_OF_Q0_CMD 0xc4248
+/* [ST 32] The number of commands received in queue 10 */
+#define USDM_REG_NUM_OF_Q10_CMD 0xc4270
+/* [ST 32] The number of commands received in queue 11 */
+#define USDM_REG_NUM_OF_Q11_CMD 0xc4274
+/* [ST 32] The number of commands received in queue 1 */
+#define USDM_REG_NUM_OF_Q1_CMD 0xc424c
+/* [ST 32] The number of commands received in queue 2 */
+#define USDM_REG_NUM_OF_Q2_CMD 0xc4250
+/* [ST 32] The number of commands received in queue 3 */
+#define USDM_REG_NUM_OF_Q3_CMD 0xc4254
+/* [ST 32] The number of commands received in queue 4 */
+#define USDM_REG_NUM_OF_Q4_CMD 0xc4258
+/* [ST 32] The number of commands received in queue 5 */
+#define USDM_REG_NUM_OF_Q5_CMD 0xc425c
+/* [ST 32] The number of commands received in queue 6 */
+#define USDM_REG_NUM_OF_Q6_CMD 0xc4260
+/* [ST 32] The number of commands received in queue 7 */
+#define USDM_REG_NUM_OF_Q7_CMD 0xc4264
+/* [ST 32] The number of commands received in queue 8 */
+#define USDM_REG_NUM_OF_Q8_CMD 0xc4268
+/* [ST 32] The number of commands received in queue 9 */
+#define USDM_REG_NUM_OF_Q9_CMD 0xc426c
+/* [RW 13] The start address in the internal RAM for the packet end message */
+#define USDM_REG_PCK_END_MSG_START_ADDR 0xc4014
+/* [RW 13] The start address in the internal RAM for queue counters */
+#define USDM_REG_Q_COUNTER_START_ADDR 0xc4010
+/* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */
+#define USDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0xc4550
+/* [R 1] parser fifo empty in sdm_sync block */
+#define USDM_REG_SYNC_PARSER_EMPTY 0xc4558
+/* [R 1] parser serial fifo empty in sdm_sync block */
+#define USDM_REG_SYNC_SYNC_EMPTY 0xc4560
+/* [RW 32] Tick for timer counter. Applicable only when
+ ~usdm_registers_timer_tick_enable.timer_tick_enable =1 */
+#define USDM_REG_TIMER_TICK 0xc4000
+/* [RW 32] Interrupt mask register #0 read/write */
+#define USDM_REG_USDM_INT_MASK_0 0xc42a0
+#define USDM_REG_USDM_INT_MASK_1 0xc42b0
+/* [R 32] Interrupt register #0 read */
+#define USDM_REG_USDM_INT_STS_0 0xc4294
+#define USDM_REG_USDM_INT_STS_1 0xc42a4
+/* [RW 11] Parity mask register #0 read/write */
+#define USDM_REG_USDM_PRTY_MASK 0xc42c0
+/* [R 11] Parity register #0 read */
+#define USDM_REG_USDM_PRTY_STS 0xc42b4
+/* [RC 11] Parity register #0 read clear */
+#define USDM_REG_USDM_PRTY_STS_CLR 0xc42b8
+/* [RW 5] The number of time_slots in the arbitration cycle */
+#define USEM_REG_ARB_CYCLE_SIZE 0x300034
+/* [RW 3] The source that is associated with arbitration element 0. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2 */
+#define USEM_REG_ARB_ELEMENT0 0x300020
+/* [RW 3] The source that is associated with arbitration element 1. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~usem_registers_arb_element0.arb_element0 */
+#define USEM_REG_ARB_ELEMENT1 0x300024
+/* [RW 3] The source that is associated with arbitration element 2. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~usem_registers_arb_element0.arb_element0
+ and ~usem_registers_arb_element1.arb_element1 */
+#define USEM_REG_ARB_ELEMENT2 0x300028
+/* [RW 3] The source that is associated with arbitration element 3. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.Could
+ not be equal to register ~usem_registers_arb_element0.arb_element0 and
+ ~usem_registers_arb_element1.arb_element1 and
+ ~usem_registers_arb_element2.arb_element2 */
+#define USEM_REG_ARB_ELEMENT3 0x30002c
+/* [RW 3] The source that is associated with arbitration element 4. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~usem_registers_arb_element0.arb_element0
+ and ~usem_registers_arb_element1.arb_element1 and
+ ~usem_registers_arb_element2.arb_element2 and
+ ~usem_registers_arb_element3.arb_element3 */
+#define USEM_REG_ARB_ELEMENT4 0x300030
+#define USEM_REG_ENABLE_IN 0x3000a4
+#define USEM_REG_ENABLE_OUT 0x3000a8
+/* [RW 32] This address space contains all registers and memories that are
+ placed in SEM_FAST block. The SEM_FAST registers are described in
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
+#define USEM_REG_FAST_MEMORY 0x320000
+/* [RW 1] Disables input messages from FIC0 May be updated during run_time
+ by the microcode */
+#define USEM_REG_FIC0_DISABLE 0x300224
+/* [RW 1] Disables input messages from FIC1 May be updated during run_time
+ by the microcode */
+#define USEM_REG_FIC1_DISABLE 0x300234
+/* [RW 15] Interrupt table Read and write access to it is not possible in
+ the middle of the work */
+#define USEM_REG_INT_TABLE 0x300400
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC0 */
+#define USEM_REG_MSG_NUM_FIC0 0x300000
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC1 */
+#define USEM_REG_MSG_NUM_FIC1 0x300004
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC0 */
+#define USEM_REG_MSG_NUM_FOC0 0x300008
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC1 */
+#define USEM_REG_MSG_NUM_FOC1 0x30000c
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC2 */
+#define USEM_REG_MSG_NUM_FOC2 0x300010
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC3 */
+#define USEM_REG_MSG_NUM_FOC3 0x300014
+/* [RW 1] Disables input messages from the passive buffer May be updated
+ during run_time by the microcode */
+#define USEM_REG_PAS_DISABLE 0x30024c
+/* [WB 128] Debug only. Passive buffer memory */
+#define USEM_REG_PASSIVE_BUFFER 0x302000
+/* [WB 46] pram memory. B45 is parity; b[44:0] - data. */
+#define USEM_REG_PRAM 0x340000
+/* [R 16] Valid sleeping threads indication have bit per thread */
+#define USEM_REG_SLEEP_THREADS_VALID 0x30026c
+/* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */
+#define USEM_REG_SLOW_EXT_STORE_EMPTY 0x3002a0
+/* [RW 16] List of free threads . There is a bit per thread. */
+#define USEM_REG_THREADS_LIST 0x3002e4
+/* [RW 3] The arbitration scheme of time_slot 0 */
+#define USEM_REG_TS_0_AS 0x300038
+/* [RW 3] The arbitration scheme of time_slot 10 */
+#define USEM_REG_TS_10_AS 0x300060
+/* [RW 3] The arbitration scheme of time_slot 11 */
+#define USEM_REG_TS_11_AS 0x300064
+/* [RW 3] The arbitration scheme of time_slot 12 */
+#define USEM_REG_TS_12_AS 0x300068
+/* [RW 3] The arbitration scheme of time_slot 13 */
+#define USEM_REG_TS_13_AS 0x30006c
+/* [RW 3] The arbitration scheme of time_slot 14 */
+#define USEM_REG_TS_14_AS 0x300070
+/* [RW 3] The arbitration scheme of time_slot 15 */
+#define USEM_REG_TS_15_AS 0x300074
+/* [RW 3] The arbitration scheme of time_slot 16 */
+#define USEM_REG_TS_16_AS 0x300078
+/* [RW 3] The arbitration scheme of time_slot 17 */
+#define USEM_REG_TS_17_AS 0x30007c
+/* [RW 3] The arbitration scheme of time_slot 18 */
+#define USEM_REG_TS_18_AS 0x300080
+/* [RW 3] The arbitration scheme of time_slot 1 */
+#define USEM_REG_TS_1_AS 0x30003c
+/* [RW 3] The arbitration scheme of time_slot 2 */
+#define USEM_REG_TS_2_AS 0x300040
+/* [RW 3] The arbitration scheme of time_slot 3 */
+#define USEM_REG_TS_3_AS 0x300044
+/* [RW 3] The arbitration scheme of time_slot 4 */
+#define USEM_REG_TS_4_AS 0x300048
+/* [RW 3] The arbitration scheme of time_slot 5 */
+#define USEM_REG_TS_5_AS 0x30004c
+/* [RW 3] The arbitration scheme of time_slot 6 */
+#define USEM_REG_TS_6_AS 0x300050
+/* [RW 3] The arbitration scheme of time_slot 7 */
+#define USEM_REG_TS_7_AS 0x300054
+/* [RW 3] The arbitration scheme of time_slot 8 */
+#define USEM_REG_TS_8_AS 0x300058
+/* [RW 3] The arbitration scheme of time_slot 9 */
+#define USEM_REG_TS_9_AS 0x30005c
+/* [RW 32] Interrupt mask register #0 read/write */
+#define USEM_REG_USEM_INT_MASK_0 0x300110
+#define USEM_REG_USEM_INT_MASK_1 0x300120
+/* [R 32] Interrupt register #0 read */
+#define USEM_REG_USEM_INT_STS_0 0x300104
+#define USEM_REG_USEM_INT_STS_1 0x300114
+/* [RW 32] Parity mask register #0 read/write */
+#define USEM_REG_USEM_PRTY_MASK_0 0x300130
+#define USEM_REG_USEM_PRTY_MASK_1 0x300140
+/* [R 32] Parity register #0 read */
+#define USEM_REG_USEM_PRTY_STS_0 0x300124
+#define USEM_REG_USEM_PRTY_STS_1 0x300134
+/* [RC 32] Parity register #0 read clear */
+#define USEM_REG_USEM_PRTY_STS_CLR_0 0x300128
+#define USEM_REG_USEM_PRTY_STS_CLR_1 0x300138
+/* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64
+ * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */
+#define USEM_REG_VFPF_ERR_NUM 0x300380
+#define VFC_MEMORIES_RST_REG_CAM_RST (0x1<<0)
+#define VFC_MEMORIES_RST_REG_RAM_RST (0x1<<1)
+#define VFC_REG_MEMORIES_RST 0x1943c
+/* [RW 32] Indirect access to AG context with 32-bits granularity. The bits
+ * [12:8] of the address should be the offset within the accessed LCID
+ * context; the bits [7:0] are the accessed LCID.Example: to write to REG10
+ * LCID100. The RBC address should be 13'ha64. */
+#define XCM_REG_AG_CTX 0x28000
+/* [RW 2] The queue index for registration on Aux1 counter flag. */
+#define XCM_REG_AUX1_Q 0x20134
+/* [RW 2] Per each decision rule the queue index to register to. */
+#define XCM_REG_AUX_CNT_FLG_Q_19 0x201b0
+/* [R 5] Used to read the XX protection CAM occupancy counter. */
+#define XCM_REG_CAM_OCCUP 0x20244
+/* [RW 1] CDU AG read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define XCM_REG_CDU_AG_RD_IFEN 0x20044
+/* [RW 1] CDU AG write Interface enable. If 0 - the request and valid input
+ are disregarded; all other signals are treated as usual; if 1 - normal
+ activity. */
+#define XCM_REG_CDU_AG_WR_IFEN 0x20040
+/* [RW 1] CDU STORM read Interface enable. If 0 - the request input is
+ disregarded; valid output is deasserted; all other signals are treated as
+ usual; if 1 - normal activity. */
+#define XCM_REG_CDU_SM_RD_IFEN 0x2004c
+/* [RW 1] CDU STORM write Interface enable. If 0 - the request and valid
+ input is disregarded; all other signals are treated as usual; if 1 -
+ normal activity. */
+#define XCM_REG_CDU_SM_WR_IFEN 0x20048
+/* [RW 4] CFC output initial credit. Max credit available - 15.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 1 at start-up. */
+#define XCM_REG_CFC_INIT_CRD 0x20404
+/* [RW 3] The weight of the CP input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_CP_WEIGHT 0x200dc
+/* [RW 1] Input csem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_CSEM_IFEN 0x20028
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the csem interface. */
+#define XCM_REG_CSEM_LENGTH_MIS 0x20228
+/* [RW 3] The weight of the input csem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_CSEM_WEIGHT 0x200c4
+/* [RW 1] Input dorq Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_DORQ_IFEN 0x20030
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the dorq interface. */
+#define XCM_REG_DORQ_LENGTH_MIS 0x20230
+/* [RW 3] The weight of the input dorq in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_DORQ_WEIGHT 0x200cc
+/* [RW 8] The Event ID in case the ErrorFlg input message bit is set. */
+#define XCM_REG_ERR_EVNT_ID 0x200b0
+/* [RW 28] The CM erroneous header for QM and Timers formatting. */
+#define XCM_REG_ERR_XCM_HDR 0x200ac
+/* [RW 8] The Event ID for Timers expiration. */
+#define XCM_REG_EXPR_EVNT_ID 0x200b4
+/* [RW 8] FIC0 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define XCM_REG_FIC0_INIT_CRD 0x2040c
+/* [RW 8] FIC1 output initial credit. Max credit available - 255.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 64 at start-up. */
+#define XCM_REG_FIC1_INIT_CRD 0x20410
+#define XCM_REG_GLB_DEL_ACK_MAX_CNT_0 0x20118
+#define XCM_REG_GLB_DEL_ACK_MAX_CNT_1 0x2011c
+#define XCM_REG_GLB_DEL_ACK_TMR_VAL_0 0x20108
+#define XCM_REG_GLB_DEL_ACK_TMR_VAL_1 0x2010c
+/* [RW 1] Arbitratiojn between Input Arbiter groups: 0 - fair Round-Robin; 1
+ - strict priority defined by ~xcm_registers_gr_ag_pr.gr_ag_pr;
+ ~xcm_registers_gr_ld0_pr.gr_ld0_pr and
+ ~xcm_registers_gr_ld1_pr.gr_ld1_pr. */
+#define XCM_REG_GR_ARB_TYPE 0x2020c
+/* [RW 2] Load (FIC0) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Channel group is the
+ compliment of the other 3 groups. */
+#define XCM_REG_GR_LD0_PR 0x20214
+/* [RW 2] Load (FIC1) channel group priority. The lowest priority is 0; the
+ highest priority is 3. It is supposed that the Channel group is the
+ compliment of the other 3 groups. */
+#define XCM_REG_GR_LD1_PR 0x20218
+/* [RW 1] Input nig0 Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_NIG0_IFEN 0x20038
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the nig0 interface. */
+#define XCM_REG_NIG0_LENGTH_MIS 0x20238
+/* [RW 3] The weight of the input nig0 in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_NIG0_WEIGHT 0x200d4
+/* [RW 1] Input nig1 Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_NIG1_IFEN 0x2003c
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the nig1 interface. */
+#define XCM_REG_NIG1_LENGTH_MIS 0x2023c
+/* [RW 5] The number of double REG-pairs; loaded from the STORM context and
+ sent to STORM; for a specific connection type. The double REG-pairs are
+ used in order to align to STORM context row size of 128 bits. The offset
+ of these data in the STORM context is always 0. Index _i stands for the
+ connection type (one of 16). */
+#define XCM_REG_N_SM_CTX_LD_0 0x20060
+#define XCM_REG_N_SM_CTX_LD_1 0x20064
+#define XCM_REG_N_SM_CTX_LD_2 0x20068
+#define XCM_REG_N_SM_CTX_LD_3 0x2006c
+#define XCM_REG_N_SM_CTX_LD_4 0x20070
+#define XCM_REG_N_SM_CTX_LD_5 0x20074
+/* [RW 1] Input pbf Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_PBF_IFEN 0x20034
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the pbf interface. */
+#define XCM_REG_PBF_LENGTH_MIS 0x20234
+/* [RW 3] The weight of the input pbf in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_PBF_WEIGHT 0x200d0
+#define XCM_REG_PHYS_QNUM3_0 0x20100
+#define XCM_REG_PHYS_QNUM3_1 0x20104
+/* [RW 8] The Event ID for Timers formatting in case of stop done. */
+#define XCM_REG_STOP_EVNT_ID 0x200b8
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the STORM interface. */
+#define XCM_REG_STORM_LENGTH_MIS 0x2021c
+/* [RW 3] The weight of the STORM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_STORM_WEIGHT 0x200bc
+/* [RW 1] STORM - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_STORM_XCM_IFEN 0x20010
+/* [RW 4] Timers output initial credit. Max credit available - 15.Write
+ writes the initial credit value; read returns the current value of the
+ credit counter. Must be initialized to 4 at start-up. */
+#define XCM_REG_TM_INIT_CRD 0x2041c
+/* [RW 3] The weight of the Timers input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_TM_WEIGHT 0x200ec
+/* [RW 28] The CM header for Timers expiration command. */
+#define XCM_REG_TM_XCM_HDR 0x200a8
+/* [RW 1] Timers - CM Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_TM_XCM_IFEN 0x2001c
+/* [RW 1] Input tsem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_TSEM_IFEN 0x20024
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the tsem interface. */
+#define XCM_REG_TSEM_LENGTH_MIS 0x20224
+/* [RW 3] The weight of the input tsem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_TSEM_WEIGHT 0x200c0
+/* [RW 2] The queue index for registration on UNA greater NXT decision rule. */
+#define XCM_REG_UNA_GT_NXT_Q 0x20120
+/* [RW 1] Input usem Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_USEM_IFEN 0x2002c
+/* [RC 1] Message length mismatch (relative to last indication) at the usem
+ interface. */
+#define XCM_REG_USEM_LENGTH_MIS 0x2022c
+/* [RW 3] The weight of the input usem in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_USEM_WEIGHT 0x200c8
+#define XCM_REG_WU_DA_CNT_CMD00 0x201d4
+#define XCM_REG_WU_DA_CNT_CMD01 0x201d8
+#define XCM_REG_WU_DA_CNT_CMD10 0x201dc
+#define XCM_REG_WU_DA_CNT_CMD11 0x201e0
+#define XCM_REG_WU_DA_CNT_UPD_VAL00 0x201e4
+#define XCM_REG_WU_DA_CNT_UPD_VAL01 0x201e8
+#define XCM_REG_WU_DA_CNT_UPD_VAL10 0x201ec
+#define XCM_REG_WU_DA_CNT_UPD_VAL11 0x201f0
+#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00 0x201c4
+#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD01 0x201c8
+#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD10 0x201cc
+#define XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD11 0x201d0
+/* [RW 1] CM - CFC Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XCM_CFC_IFEN 0x20050
+/* [RW 14] Interrupt mask register #0 read/write */
+#define XCM_REG_XCM_INT_MASK 0x202b4
+/* [R 14] Interrupt register #0 read */
+#define XCM_REG_XCM_INT_STS 0x202a8
+/* [RW 30] Parity mask register #0 read/write */
+#define XCM_REG_XCM_PRTY_MASK 0x202c4
+/* [R 30] Parity register #0 read */
+#define XCM_REG_XCM_PRTY_STS 0x202b8
+/* [RC 30] Parity register #0 read clear */
+#define XCM_REG_XCM_PRTY_STS_CLR 0x202bc
+
+/* [RW 4] The size of AG context region 0 in REG-pairs. Designates the MS
+ REG-pair number (e.g. if region 0 is 6 REG-pairs; the value should be 5).
+ Is used to determine the number of the AG context REG-pairs written back;
+ when the Reg1WbFlg isn't set. */
+#define XCM_REG_XCM_REG0_SZ 0x200f4
+/* [RW 1] CM - STORM 0 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XCM_STORM0_IFEN 0x20004
+/* [RW 1] CM - STORM 1 Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XCM_STORM1_IFEN 0x20008
+/* [RW 1] CM - Timers Interface enable. If 0 - the valid input is
+ disregarded; acknowledge output is deasserted; all other signals are
+ treated as usual; if 1 - normal activity. */
+#define XCM_REG_XCM_TM_IFEN 0x20020
+/* [RW 1] CM - QM Interface enable. If 0 - the acknowledge input is
+ disregarded; valid is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XCM_XQM_IFEN 0x2000c
+/* [RW 1] If set the Q index; received from the QM is inserted to event ID. */
+#define XCM_REG_XCM_XQM_USE_Q 0x200f0
+/* [RW 4] The value by which CFC updates the activity counter at QM bypass. */
+#define XCM_REG_XQM_BYP_ACT_UPD 0x200fc
+/* [RW 6] QM output initial credit. Max credit available - 32.Write writes
+ the initial credit value; read returns the current value of the credit
+ counter. Must be initialized to 32 at start-up. */
+#define XCM_REG_XQM_INIT_CRD 0x20420
+/* [RW 3] The weight of the QM (primary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_XQM_P_WEIGHT 0x200e4
+/* [RW 3] The weight of the QM (secondary) input in the WRR mechanism. 0
+ stands for weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_XQM_S_WEIGHT 0x200e8
+/* [RW 28] The CM header value for QM request (primary). */
+#define XCM_REG_XQM_XCM_HDR_P 0x200a0
+/* [RW 28] The CM header value for QM request (secondary). */
+#define XCM_REG_XQM_XCM_HDR_S 0x200a4
+/* [RW 1] QM - CM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XQM_XCM_IFEN 0x20014
+/* [RW 1] Input SDM Interface enable. If 0 - the valid input is disregarded;
+ acknowledge output is deasserted; all other signals are treated as usual;
+ if 1 - normal activity. */
+#define XCM_REG_XSDM_IFEN 0x20018
+/* [RC 1] Set at message length mismatch (relative to last indication) at
+ the SDM interface. */
+#define XCM_REG_XSDM_LENGTH_MIS 0x20220
+/* [RW 3] The weight of the SDM input in the WRR mechanism. 0 stands for
+ weight 8 (the most prioritised); 1 stands for weight 1(least
+ prioritised); 2 stands for weight 2; tc. */
+#define XCM_REG_XSDM_WEIGHT 0x200e0
+/* [RW 17] Indirect access to the descriptor table of the XX protection
+ mechanism. The fields are: [5:0] - message length; 11:6] - message
+ pointer; 16:12] - next pointer. */
+#define XCM_REG_XX_DESCR_TABLE 0x20480
+#define XCM_REG_XX_DESCR_TABLE_SIZE 32
+/* [R 6] Used to read the XX protection Free counter. */
+#define XCM_REG_XX_FREE 0x20240
+/* [RW 6] Initial value for the credit counter; responsible for fulfilling
+ of the Input Stage XX protection buffer by the XX protection pending
+ messages. Max credit available - 3.Write writes the initial credit value;
+ read returns the current value of the credit counter. Must be initialized
+ to 2 at start-up. */
+#define XCM_REG_XX_INIT_CRD 0x20424
+/* [RW 6] The maximum number of pending messages; which may be stored in XX
+ protection. ~xcm_registers_xx_free.xx_free read on read. */
+#define XCM_REG_XX_MSG_NUM 0x20428
+/* [RW 8] The Event ID; sent to the STORM in case of XX overflow. */
+#define XCM_REG_XX_OVFL_EVNT_ID 0x20058
+#define XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_LOCAL_FAULT_STATUS (0x1<<0)
+#define XMAC_CLEAR_RX_LSS_STATUS_REG_CLEAR_REMOTE_FAULT_STATUS (0x1<<1)
+#define XMAC_CTRL_REG_LINE_LOCAL_LPBK (0x1<<2)
+#define XMAC_CTRL_REG_RX_EN (0x1<<1)
+#define XMAC_CTRL_REG_SOFT_RESET (0x1<<6)
+#define XMAC_CTRL_REG_TX_EN (0x1<<0)
+#define XMAC_CTRL_REG_XLGMII_ALIGN_ENB (0x1<<7)
+#define XMAC_PAUSE_CTRL_REG_RX_PAUSE_EN (0x1<<18)
+#define XMAC_PAUSE_CTRL_REG_TX_PAUSE_EN (0x1<<17)
+#define XMAC_PFC_CTRL_HI_REG_FORCE_PFC_XON (0x1<<1)
+#define XMAC_PFC_CTRL_HI_REG_PFC_REFRESH_EN (0x1<<0)
+#define XMAC_PFC_CTRL_HI_REG_PFC_STATS_EN (0x1<<3)
+#define XMAC_PFC_CTRL_HI_REG_RX_PFC_EN (0x1<<4)
+#define XMAC_PFC_CTRL_HI_REG_TX_PFC_EN (0x1<<5)
+#define XMAC_REG_CLEAR_RX_LSS_STATUS 0x60
+#define XMAC_REG_CTRL 0
+/* [RW 16] Upper 48 bits of ctrl_sa register. Used as the SA in PAUSE/PFC
+ * packets transmitted by the MAC */
+#define XMAC_REG_CTRL_SA_HI 0x2c
+/* [RW 32] Lower 48 bits of ctrl_sa register. Used as the SA in PAUSE/PFC
+ * packets transmitted by the MAC */
+#define XMAC_REG_CTRL_SA_LO 0x28
+#define XMAC_REG_EEE_CTRL 0xd8
+#define XMAC_REG_EEE_TIMERS_HI 0xe4
+#define XMAC_REG_PAUSE_CTRL 0x68
+#define XMAC_REG_PFC_CTRL 0x70
+#define XMAC_REG_PFC_CTRL_HI 0x74
+#define XMAC_REG_RX_LSS_CTRL 0x50
+#define XMAC_REG_RX_LSS_STATUS 0x58
+/* [RW 14] Maximum packet size in receive direction; exclusive of preamble &
+ * CRC in strip mode */
+#define XMAC_REG_RX_MAX_SIZE 0x40
+#define XMAC_REG_TX_CTRL 0x20
+#define XMAC_RX_LSS_CTRL_REG_LOCAL_FAULT_DISABLE (0x1<<0)
+#define XMAC_RX_LSS_CTRL_REG_REMOTE_FAULT_DISABLE (0x1<<1)
+/* [RW 16] Indirect access to the XX table of the XX protection mechanism.
+ The fields are:[4:0] - tail pointer; 9:5] - Link List size; 14:10] -
+ header pointer. */
+#define XCM_REG_XX_TABLE 0x20500
+/* [RW 8] The event id for aggregated interrupt 0 */
+#define XSDM_REG_AGG_INT_EVENT_0 0x166038
+#define XSDM_REG_AGG_INT_EVENT_1 0x16603c
+#define XSDM_REG_AGG_INT_EVENT_10 0x166060
+#define XSDM_REG_AGG_INT_EVENT_11 0x166064
+#define XSDM_REG_AGG_INT_EVENT_12 0x166068
+#define XSDM_REG_AGG_INT_EVENT_13 0x16606c
+#define XSDM_REG_AGG_INT_EVENT_14 0x166070
+#define XSDM_REG_AGG_INT_EVENT_2 0x166040
+#define XSDM_REG_AGG_INT_EVENT_3 0x166044
+#define XSDM_REG_AGG_INT_EVENT_4 0x166048
+#define XSDM_REG_AGG_INT_EVENT_5 0x16604c
+#define XSDM_REG_AGG_INT_EVENT_6 0x166050
+#define XSDM_REG_AGG_INT_EVENT_7 0x166054
+#define XSDM_REG_AGG_INT_EVENT_8 0x166058
+#define XSDM_REG_AGG_INT_EVENT_9 0x16605c
+/* [RW 1] For each aggregated interrupt index whether the mode is normal (0)
+ or auto-mask-mode (1) */
+#define XSDM_REG_AGG_INT_MODE_0 0x1661b8
+#define XSDM_REG_AGG_INT_MODE_1 0x1661bc
+/* [RW 13] The start address in the internal RAM for the cfc_rsp lcid */
+#define XSDM_REG_CFC_RSP_START_ADDR 0x166008
+/* [RW 16] The maximum value of the completion counter #0 */
+#define XSDM_REG_CMP_COUNTER_MAX0 0x16601c
+/* [RW 16] The maximum value of the completion counter #1 */
+#define XSDM_REG_CMP_COUNTER_MAX1 0x166020
+/* [RW 16] The maximum value of the completion counter #2 */
+#define XSDM_REG_CMP_COUNTER_MAX2 0x166024
+/* [RW 16] The maximum value of the completion counter #3 */
+#define XSDM_REG_CMP_COUNTER_MAX3 0x166028
+/* [RW 13] The start address in the internal RAM for the completion
+ counters. */
+#define XSDM_REG_CMP_COUNTER_START_ADDR 0x16600c
+#define XSDM_REG_ENABLE_IN1 0x166238
+#define XSDM_REG_ENABLE_IN2 0x16623c
+#define XSDM_REG_ENABLE_OUT1 0x166240
+#define XSDM_REG_ENABLE_OUT2 0x166244
+/* [RW 4] The initial number of messages that can be sent to the pxp control
+ interface without receiving any ACK. */
+#define XSDM_REG_INIT_CREDIT_PXP_CTRL 0x1664bc
+/* [ST 32] The number of ACK after placement messages received */
+#define XSDM_REG_NUM_OF_ACK_AFTER_PLACE 0x16627c
+/* [ST 32] The number of packet end messages received from the parser */
+#define XSDM_REG_NUM_OF_PKT_END_MSG 0x166274
+/* [ST 32] The number of requests received from the pxp async if */
+#define XSDM_REG_NUM_OF_PXP_ASYNC_REQ 0x166278
+/* [ST 32] The number of commands received in queue 0 */
+#define XSDM_REG_NUM_OF_Q0_CMD 0x166248
+/* [ST 32] The number of commands received in queue 10 */
+#define XSDM_REG_NUM_OF_Q10_CMD 0x16626c
+/* [ST 32] The number of commands received in queue 11 */
+#define XSDM_REG_NUM_OF_Q11_CMD 0x166270
+/* [ST 32] The number of commands received in queue 1 */
+#define XSDM_REG_NUM_OF_Q1_CMD 0x16624c
+/* [ST 32] The number of commands received in queue 3 */
+#define XSDM_REG_NUM_OF_Q3_CMD 0x166250
+/* [ST 32] The number of commands received in queue 4 */
+#define XSDM_REG_NUM_OF_Q4_CMD 0x166254
+/* [ST 32] The number of commands received in queue 5 */
+#define XSDM_REG_NUM_OF_Q5_CMD 0x166258
+/* [ST 32] The number of commands received in queue 6 */
+#define XSDM_REG_NUM_OF_Q6_CMD 0x16625c
+/* [ST 32] The number of commands received in queue 7 */
+#define XSDM_REG_NUM_OF_Q7_CMD 0x166260
+/* [ST 32] The number of commands received in queue 8 */
+#define XSDM_REG_NUM_OF_Q8_CMD 0x166264
+/* [ST 32] The number of commands received in queue 9 */
+#define XSDM_REG_NUM_OF_Q9_CMD 0x166268
+/* [RW 13] The start address in the internal RAM for queue counters */
+#define XSDM_REG_Q_COUNTER_START_ADDR 0x166010
+/* [W 17] Generate an operation after completion; bit-16 is
+ * AggVectIdx_valid; bits 15:8 are AggVectIdx; bits 7:5 are the TRIG and
+ * bits 4:0 are the T124Param[4:0] */
+#define XSDM_REG_OPERATION_GEN 0x1664c4
+/* [R 1] pxp_ctrl rd_data fifo empty in sdm_dma_rsp block */
+#define XSDM_REG_RSP_PXP_CTRL_RDATA_EMPTY 0x166548
+/* [R 1] parser fifo empty in sdm_sync block */
+#define XSDM_REG_SYNC_PARSER_EMPTY 0x166550
+/* [R 1] parser serial fifo empty in sdm_sync block */
+#define XSDM_REG_SYNC_SYNC_EMPTY 0x166558
+/* [RW 32] Tick for timer counter. Applicable only when
+ ~xsdm_registers_timer_tick_enable.timer_tick_enable =1 */
+#define XSDM_REG_TIMER_TICK 0x166000
+/* [RW 32] Interrupt mask register #0 read/write */
+#define XSDM_REG_XSDM_INT_MASK_0 0x16629c
+#define XSDM_REG_XSDM_INT_MASK_1 0x1662ac
+/* [R 32] Interrupt register #0 read */
+#define XSDM_REG_XSDM_INT_STS_0 0x166290
+#define XSDM_REG_XSDM_INT_STS_1 0x1662a0
+/* [RW 11] Parity mask register #0 read/write */
+#define XSDM_REG_XSDM_PRTY_MASK 0x1662bc
+/* [R 11] Parity register #0 read */
+#define XSDM_REG_XSDM_PRTY_STS 0x1662b0
+/* [RC 11] Parity register #0 read clear */
+#define XSDM_REG_XSDM_PRTY_STS_CLR 0x1662b4
+/* [RW 5] The number of time_slots in the arbitration cycle */
+#define XSEM_REG_ARB_CYCLE_SIZE 0x280034
+/* [RW 3] The source that is associated with arbitration element 0. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2 */
+#define XSEM_REG_ARB_ELEMENT0 0x280020
+/* [RW 3] The source that is associated with arbitration element 1. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~xsem_registers_arb_element0.arb_element0 */
+#define XSEM_REG_ARB_ELEMENT1 0x280024
+/* [RW 3] The source that is associated with arbitration element 2. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~xsem_registers_arb_element0.arb_element0
+ and ~xsem_registers_arb_element1.arb_element1 */
+#define XSEM_REG_ARB_ELEMENT2 0x280028
+/* [RW 3] The source that is associated with arbitration element 3. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.Could
+ not be equal to register ~xsem_registers_arb_element0.arb_element0 and
+ ~xsem_registers_arb_element1.arb_element1 and
+ ~xsem_registers_arb_element2.arb_element2 */
+#define XSEM_REG_ARB_ELEMENT3 0x28002c
+/* [RW 3] The source that is associated with arbitration element 4. Source
+ decoding is: 0- foc0; 1-fic1; 2-sleeping thread with priority 0; 3-
+ sleeping thread with priority 1; 4- sleeping thread with priority 2.
+ Could not be equal to register ~xsem_registers_arb_element0.arb_element0
+ and ~xsem_registers_arb_element1.arb_element1 and
+ ~xsem_registers_arb_element2.arb_element2 and
+ ~xsem_registers_arb_element3.arb_element3 */
+#define XSEM_REG_ARB_ELEMENT4 0x280030
+#define XSEM_REG_ENABLE_IN 0x2800a4
+#define XSEM_REG_ENABLE_OUT 0x2800a8
+/* [RW 32] This address space contains all registers and memories that are
+ placed in SEM_FAST block. The SEM_FAST registers are described in
+ appendix B. In order to access the sem_fast registers the base address
+ ~fast_memory.fast_memory should be added to eachsem_fast register offset. */
+#define XSEM_REG_FAST_MEMORY 0x2a0000
+/* [RW 1] Disables input messages from FIC0 May be updated during run_time
+ by the microcode */
+#define XSEM_REG_FIC0_DISABLE 0x280224
+/* [RW 1] Disables input messages from FIC1 May be updated during run_time
+ by the microcode */
+#define XSEM_REG_FIC1_DISABLE 0x280234
+/* [RW 15] Interrupt table Read and write access to it is not possible in
+ the middle of the work */
+#define XSEM_REG_INT_TABLE 0x280400
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC0 */
+#define XSEM_REG_MSG_NUM_FIC0 0x280000
+/* [ST 24] Statistics register. The number of messages that entered through
+ FIC1 */
+#define XSEM_REG_MSG_NUM_FIC1 0x280004
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC0 */
+#define XSEM_REG_MSG_NUM_FOC0 0x280008
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC1 */
+#define XSEM_REG_MSG_NUM_FOC1 0x28000c
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC2 */
+#define XSEM_REG_MSG_NUM_FOC2 0x280010
+/* [ST 24] Statistics register. The number of messages that were sent to
+ FOC3 */
+#define XSEM_REG_MSG_NUM_FOC3 0x280014
+/* [RW 1] Disables input messages from the passive buffer May be updated
+ during run_time by the microcode */
+#define XSEM_REG_PAS_DISABLE 0x28024c
+/* [WB 128] Debug only. Passive buffer memory */
+#define XSEM_REG_PASSIVE_BUFFER 0x282000
+/* [WB 46] pram memory. B45 is parity; b[44:0] - data. */
+#define XSEM_REG_PRAM 0x2c0000
+/* [R 16] Valid sleeping threads indication have bit per thread */
+#define XSEM_REG_SLEEP_THREADS_VALID 0x28026c
+/* [R 1] EXT_STORE FIFO is empty in sem_slow_ls_ext */
+#define XSEM_REG_SLOW_EXT_STORE_EMPTY 0x2802a0
+/* [RW 16] List of free threads . There is a bit per thread. */
+#define XSEM_REG_THREADS_LIST 0x2802e4
+/* [RW 3] The arbitration scheme of time_slot 0 */
+#define XSEM_REG_TS_0_AS 0x280038
+/* [RW 3] The arbitration scheme of time_slot 10 */
+#define XSEM_REG_TS_10_AS 0x280060
+/* [RW 3] The arbitration scheme of time_slot 11 */
+#define XSEM_REG_TS_11_AS 0x280064
+/* [RW 3] The arbitration scheme of time_slot 12 */
+#define XSEM_REG_TS_12_AS 0x280068
+/* [RW 3] The arbitration scheme of time_slot 13 */
+#define XSEM_REG_TS_13_AS 0x28006c
+/* [RW 3] The arbitration scheme of time_slot 14 */
+#define XSEM_REG_TS_14_AS 0x280070
+/* [RW 3] The arbitration scheme of time_slot 15 */
+#define XSEM_REG_TS_15_AS 0x280074
+/* [RW 3] The arbitration scheme of time_slot 16 */
+#define XSEM_REG_TS_16_AS 0x280078
+/* [RW 3] The arbitration scheme of time_slot 17 */
+#define XSEM_REG_TS_17_AS 0x28007c
+/* [RW 3] The arbitration scheme of time_slot 18 */
+#define XSEM_REG_TS_18_AS 0x280080
+/* [RW 3] The arbitration scheme of time_slot 1 */
+#define XSEM_REG_TS_1_AS 0x28003c
+/* [RW 3] The arbitration scheme of time_slot 2 */
+#define XSEM_REG_TS_2_AS 0x280040
+/* [RW 3] The arbitration scheme of time_slot 3 */
+#define XSEM_REG_TS_3_AS 0x280044
+/* [RW 3] The arbitration scheme of time_slot 4 */
+#define XSEM_REG_TS_4_AS 0x280048
+/* [RW 3] The arbitration scheme of time_slot 5 */
+#define XSEM_REG_TS_5_AS 0x28004c
+/* [RW 3] The arbitration scheme of time_slot 6 */
+#define XSEM_REG_TS_6_AS 0x280050
+/* [RW 3] The arbitration scheme of time_slot 7 */
+#define XSEM_REG_TS_7_AS 0x280054
+/* [RW 3] The arbitration scheme of time_slot 8 */
+#define XSEM_REG_TS_8_AS 0x280058
+/* [RW 3] The arbitration scheme of time_slot 9 */
+#define XSEM_REG_TS_9_AS 0x28005c
+/* [W 7] VF or PF ID for reset error bit. Values 0-63 reset error bit for 64
+ * VF; values 64-67 reset error for 4 PF; values 68-127 are not valid. */
+#define XSEM_REG_VFPF_ERR_NUM 0x280380
+/* [RW 32] Interrupt mask register #0 read/write */
+#define XSEM_REG_XSEM_INT_MASK_0 0x280110
+#define XSEM_REG_XSEM_INT_MASK_1 0x280120
+/* [R 32] Interrupt register #0 read */
+#define XSEM_REG_XSEM_INT_STS_0 0x280104
+#define XSEM_REG_XSEM_INT_STS_1 0x280114
+/* [RW 32] Parity mask register #0 read/write */
+#define XSEM_REG_XSEM_PRTY_MASK_0 0x280130
+#define XSEM_REG_XSEM_PRTY_MASK_1 0x280140
+/* [R 32] Parity register #0 read */
+#define XSEM_REG_XSEM_PRTY_STS_0 0x280124
+#define XSEM_REG_XSEM_PRTY_STS_1 0x280134
+/* [RC 32] Parity register #0 read clear */
+#define XSEM_REG_XSEM_PRTY_STS_CLR_0 0x280128
+#define XSEM_REG_XSEM_PRTY_STS_CLR_1 0x280138
+#define MCPR_ACCESS_LOCK_LOCK (1L<<31)
+#define MCPR_NVM_ACCESS_ENABLE_EN (1L<<0)
+#define MCPR_NVM_ACCESS_ENABLE_WR_EN (1L<<1)
+#define MCPR_NVM_ADDR_NVM_ADDR_VALUE (0xffffffL<<0)
+#define MCPR_NVM_CFG4_FLASH_SIZE (0x7L<<0)
+#define MCPR_NVM_COMMAND_DOIT (1L<<4)
+#define MCPR_NVM_COMMAND_DONE (1L<<3)
+#define MCPR_NVM_COMMAND_FIRST (1L<<7)
+#define MCPR_NVM_COMMAND_LAST (1L<<8)
+#define MCPR_NVM_COMMAND_WR (1L<<5)
+#define MCPR_NVM_SW_ARB_ARB_ARB1 (1L<<9)
+#define MCPR_NVM_SW_ARB_ARB_REQ_CLR1 (1L<<5)
+#define MCPR_NVM_SW_ARB_ARB_REQ_SET1 (1L<<1)
+#define BIGMAC_REGISTER_BMAC_CONTROL (0x00<<3)
+#define BIGMAC_REGISTER_BMAC_XGXS_CONTROL (0x01<<3)
+#define BIGMAC_REGISTER_CNT_MAX_SIZE (0x05<<3)
+#define BIGMAC_REGISTER_RX_CONTROL (0x21<<3)
+#define BIGMAC_REGISTER_RX_LLFC_MSG_FLDS (0x46<<3)
+#define BIGMAC_REGISTER_RX_LSS_STATUS (0x43<<3)
+#define BIGMAC_REGISTER_RX_MAX_SIZE (0x23<<3)
+#define BIGMAC_REGISTER_RX_STAT_GR64 (0x26<<3)
+#define BIGMAC_REGISTER_RX_STAT_GRIPJ (0x42<<3)
+#define BIGMAC_REGISTER_TX_CONTROL (0x07<<3)
+#define BIGMAC_REGISTER_TX_MAX_SIZE (0x09<<3)
+#define BIGMAC_REGISTER_TX_PAUSE_THRESHOLD (0x0A<<3)
+#define BIGMAC_REGISTER_TX_SOURCE_ADDR (0x08<<3)
+#define BIGMAC_REGISTER_TX_STAT_GTBYT (0x20<<3)
+#define BIGMAC_REGISTER_TX_STAT_GTPKT (0x0C<<3)
+#define BIGMAC2_REGISTER_BMAC_CONTROL (0x00<<3)
+#define BIGMAC2_REGISTER_BMAC_XGXS_CONTROL (0x01<<3)
+#define BIGMAC2_REGISTER_CNT_MAX_SIZE (0x05<<3)
+#define BIGMAC2_REGISTER_PFC_CONTROL (0x06<<3)
+#define BIGMAC2_REGISTER_RX_CONTROL (0x3A<<3)
+#define BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS (0x62<<3)
+#define BIGMAC2_REGISTER_RX_LSS_STAT (0x3E<<3)
+#define BIGMAC2_REGISTER_RX_MAX_SIZE (0x3C<<3)
+#define BIGMAC2_REGISTER_RX_STAT_GR64 (0x40<<3)
+#define BIGMAC2_REGISTER_RX_STAT_GRIPJ (0x5f<<3)
+#define BIGMAC2_REGISTER_RX_STAT_GRPP (0x51<<3)
+#define BIGMAC2_REGISTER_TX_CONTROL (0x1C<<3)
+#define BIGMAC2_REGISTER_TX_MAX_SIZE (0x1E<<3)
+#define BIGMAC2_REGISTER_TX_PAUSE_CONTROL (0x20<<3)
+#define BIGMAC2_REGISTER_TX_SOURCE_ADDR (0x1D<<3)
+#define BIGMAC2_REGISTER_TX_STAT_GTBYT (0x39<<3)
+#define BIGMAC2_REGISTER_TX_STAT_GTPOK (0x22<<3)
+#define BIGMAC2_REGISTER_TX_STAT_GTPP (0x24<<3)
+#define EMAC_LED_1000MB_OVERRIDE (1L<<1)
+#define EMAC_LED_100MB_OVERRIDE (1L<<2)
+#define EMAC_LED_10MB_OVERRIDE (1L<<3)
+#define EMAC_LED_2500MB_OVERRIDE (1L<<12)
+#define EMAC_LED_OVERRIDE (1L<<0)
+#define EMAC_LED_TRAFFIC (1L<<6)
+#define EMAC_MDIO_COMM_COMMAND_ADDRESS (0L<<26)
+#define EMAC_MDIO_COMM_COMMAND_READ_22 (2L<<26)
+#define EMAC_MDIO_COMM_COMMAND_READ_45 (3L<<26)
+#define EMAC_MDIO_COMM_COMMAND_WRITE_22 (1L<<26)
+#define EMAC_MDIO_COMM_COMMAND_WRITE_45 (1L<<26)
+#define EMAC_MDIO_COMM_DATA (0xffffL<<0)
+#define EMAC_MDIO_COMM_START_BUSY (1L<<29)
+#define EMAC_MDIO_MODE_AUTO_POLL (1L<<4)
+#define EMAC_MDIO_MODE_CLAUSE_45 (1L<<31)
+#define EMAC_MDIO_MODE_CLOCK_CNT (0x3ffL<<16)
+#define EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT 16
+#define EMAC_MDIO_STATUS_10MB (1L<<1)
+#define EMAC_MODE_25G_MODE (1L<<5)
+#define EMAC_MODE_HALF_DUPLEX (1L<<1)
+#define EMAC_MODE_PORT_GMII (2L<<2)
+#define EMAC_MODE_PORT_MII (1L<<2)
+#define EMAC_MODE_PORT_MII_10M (3L<<2)
+#define EMAC_MODE_RESET (1L<<0)
+#define EMAC_REG_EMAC_LED 0xc
+#define EMAC_REG_EMAC_MAC_MATCH 0x10
+#define EMAC_REG_EMAC_MDIO_COMM 0xac
+#define EMAC_REG_EMAC_MDIO_MODE 0xb4
+#define EMAC_REG_EMAC_MDIO_STATUS 0xb0
+#define EMAC_REG_EMAC_MODE 0x0
+#define EMAC_REG_EMAC_RX_MODE 0xc8
+#define EMAC_REG_EMAC_RX_MTU_SIZE 0x9c
+#define EMAC_REG_EMAC_RX_STAT_AC 0x180
+#define EMAC_REG_EMAC_RX_STAT_AC_28 0x1f4
+#define EMAC_REG_EMAC_RX_STAT_AC_COUNT 23
+#define EMAC_REG_EMAC_TX_MODE 0xbc
+#define EMAC_REG_EMAC_TX_STAT_AC 0x280
+#define EMAC_REG_EMAC_TX_STAT_AC_COUNT 22
+#define EMAC_REG_RX_PFC_MODE 0x320
+#define EMAC_REG_RX_PFC_MODE_PRIORITIES (1L<<2)
+#define EMAC_REG_RX_PFC_MODE_RX_EN (1L<<1)
+#define EMAC_REG_RX_PFC_MODE_TX_EN (1L<<0)
+#define EMAC_REG_RX_PFC_PARAM 0x324
+#define EMAC_REG_RX_PFC_PARAM_OPCODE_BITSHIFT 0
+#define EMAC_REG_RX_PFC_PARAM_PRIORITY_EN_BITSHIFT 16
+#define EMAC_REG_RX_PFC_STATS_XOFF_RCVD 0x328
+#define EMAC_REG_RX_PFC_STATS_XOFF_RCVD_COUNT (0xffff<<0)
+#define EMAC_REG_RX_PFC_STATS_XOFF_SENT 0x330
+#define EMAC_REG_RX_PFC_STATS_XOFF_SENT_COUNT (0xffff<<0)
+#define EMAC_REG_RX_PFC_STATS_XON_RCVD 0x32c
+#define EMAC_REG_RX_PFC_STATS_XON_RCVD_COUNT (0xffff<<0)
+#define EMAC_REG_RX_PFC_STATS_XON_SENT 0x334
+#define EMAC_REG_RX_PFC_STATS_XON_SENT_COUNT (0xffff<<0)
+#define EMAC_RX_MODE_FLOW_EN (1L<<2)
+#define EMAC_RX_MODE_KEEP_MAC_CONTROL (1L<<3)
+#define EMAC_RX_MODE_KEEP_VLAN_TAG (1L<<10)
+#define EMAC_RX_MODE_PROMISCUOUS (1L<<8)
+#define EMAC_RX_MODE_RESET (1L<<0)
+#define EMAC_RX_MTU_SIZE_JUMBO_ENA (1L<<31)
+#define EMAC_TX_MODE_EXT_PAUSE_EN (1L<<3)
+#define EMAC_TX_MODE_FLOW_EN (1L<<4)
+#define EMAC_TX_MODE_RESET (1L<<0)
+#define MISC_REGISTERS_GPIO_0 0
+#define MISC_REGISTERS_GPIO_1 1
+#define MISC_REGISTERS_GPIO_2 2
+#define MISC_REGISTERS_GPIO_3 3
+#define MISC_REGISTERS_GPIO_CLR_POS 16
+#define MISC_REGISTERS_GPIO_FLOAT (0xffL<<24)
+#define MISC_REGISTERS_GPIO_FLOAT_POS 24
+#define MISC_REGISTERS_GPIO_HIGH 1
+#define MISC_REGISTERS_GPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_GPIO_INT_CLR_POS 24
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_CLR 0
+#define MISC_REGISTERS_GPIO_INT_OUTPUT_SET 1
+#define MISC_REGISTERS_GPIO_INT_SET_POS 16
+#define MISC_REGISTERS_GPIO_LOW 0
+#define MISC_REGISTERS_GPIO_OUTPUT_HIGH 1
+#define MISC_REGISTERS_GPIO_OUTPUT_LOW 0
+#define MISC_REGISTERS_GPIO_PORT_SHIFT 4
+#define MISC_REGISTERS_GPIO_SET_POS 8
+#define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_BRB1 (0x1<<0)
+#define MISC_REGISTERS_RESET_REG_1_RST_DORQ (0x1<<19)
+#define MISC_REGISTERS_RESET_REG_1_RST_HC (0x1<<29)
+#define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7)
+#define MISC_REGISTERS_RESET_REG_1_RST_PXP (0x1<<26)
+#define MISC_REGISTERS_RESET_REG_1_RST_PXPV (0x1<<27)
+#define MISC_REGISTERS_RESET_REG_1_RST_XSEM (0x1<<22)
+#define MISC_REGISTERS_RESET_REG_1_SET 0x584
+#define MISC_REGISTERS_RESET_REG_2_CLEAR 0x598
+#define MISC_REGISTERS_RESET_REG_2_MSTAT0 (0x1<<24)
+#define MISC_REGISTERS_RESET_REG_2_MSTAT1 (0x1<<25)
+#define MISC_REGISTERS_RESET_REG_2_PGLC (0x1<<19)
+#define MISC_REGISTERS_RESET_REG_2_RST_ATC (0x1<<17)
+#define MISC_REGISTERS_RESET_REG_2_RST_BMAC0 (0x1<<0)
+#define MISC_REGISTERS_RESET_REG_2_RST_BMAC1 (0x1<<1)
+#define MISC_REGISTERS_RESET_REG_2_RST_EMAC0 (0x1<<2)
+#define MISC_REGISTERS_RESET_REG_2_RST_EMAC0_HARD_CORE (0x1<<14)
+#define MISC_REGISTERS_RESET_REG_2_RST_EMAC1 (0x1<<3)
+#define MISC_REGISTERS_RESET_REG_2_RST_EMAC1_HARD_CORE (0x1<<15)
+#define MISC_REGISTERS_RESET_REG_2_RST_GRC (0x1<<4)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_HARD_CORE_RST_B (0x1<<6)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_CMN_CORE (0x1<<8)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_CMN_CPU (0x1<<7)
+#define MISC_REGISTERS_RESET_REG_2_RST_MCP_N_RESET_REG_HARD_CORE (0x1<<5)
+#define MISC_REGISTERS_RESET_REG_2_RST_MDIO (0x1<<13)
+#define MISC_REGISTERS_RESET_REG_2_RST_MISC_CORE (0x1<<11)
+#define MISC_REGISTERS_RESET_REG_2_RST_PCI_MDIO (0x1<<13)
+#define MISC_REGISTERS_RESET_REG_2_RST_RBCN (0x1<<9)
+#define MISC_REGISTERS_RESET_REG_2_SET 0x594
+#define MISC_REGISTERS_RESET_REG_2_UMAC0 (0x1<<20)
+#define MISC_REGISTERS_RESET_REG_2_UMAC1 (0x1<<21)
+#define MISC_REGISTERS_RESET_REG_2_XMAC (0x1<<22)
+#define MISC_REGISTERS_RESET_REG_2_XMAC_SOFT (0x1<<23)
+#define MISC_REGISTERS_RESET_REG_3_CLEAR 0x5a8
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_IDDQ (0x1<<1)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN (0x1<<2)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_PWRDWN_SD (0x1<<3)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_SERDES0_RSTB_HW (0x1<<0)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_IDDQ (0x1<<5)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN (0x1<<6)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_PWRDWN_SD (0x1<<7)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_RSTB_HW (0x1<<4)
+#define MISC_REGISTERS_RESET_REG_3_MISC_NIG_MUX_XGXS0_TXD_FIFO_RSTB (0x1<<8)
+#define MISC_REGISTERS_RESET_REG_3_SET 0x5a4
+#define MISC_REGISTERS_SPIO_4 4
+#define MISC_REGISTERS_SPIO_5 5
+#define MISC_REGISTERS_SPIO_7 7
+#define MISC_REGISTERS_SPIO_CLR_POS 16
+#define MISC_REGISTERS_SPIO_FLOAT (0xffL<<24)
+#define MISC_REGISTERS_SPIO_FLOAT_POS 24
+#define MISC_REGISTERS_SPIO_INPUT_HI_Z 2
+#define MISC_REGISTERS_SPIO_INT_OLD_SET_POS 16
+#define MISC_REGISTERS_SPIO_OUTPUT_HIGH 1
+#define MISC_REGISTERS_SPIO_OUTPUT_LOW 0
+#define MISC_REGISTERS_SPIO_SET_POS 8
+#define MISC_SPIO_CLR_POS 16
+#define MISC_SPIO_FLOAT (0xffL<<24)
+#define MISC_SPIO_FLOAT_POS 24
+#define MISC_SPIO_INPUT_HI_Z 2
+#define MISC_SPIO_INT_OLD_SET_POS 16
+#define MISC_SPIO_OUTPUT_HIGH 1
+#define MISC_SPIO_OUTPUT_LOW 0
+#define MISC_SPIO_SET_POS 8
+#define MISC_SPIO_SPIO4 0x10
+#define MISC_SPIO_SPIO5 0x20
+#define HW_LOCK_MAX_RESOURCE_VALUE 31
+#define HW_LOCK_RESOURCE_DCBX_ADMIN_MIB 13
+#define HW_LOCK_RESOURCE_DRV_FLAGS 10
+#define HW_LOCK_RESOURCE_GPIO 1
+#define HW_LOCK_RESOURCE_MDIO 0
+#define HW_LOCK_RESOURCE_NVRAM 12
+#define HW_LOCK_RESOURCE_PORT0_ATT_MASK 3
+#define HW_LOCK_RESOURCE_RECOVERY_LEADER_0 8
+#define HW_LOCK_RESOURCE_RECOVERY_LEADER_1 9
+#define HW_LOCK_RESOURCE_RECOVERY_REG 11
+#define HW_LOCK_RESOURCE_RESET 5
+#define HW_LOCK_RESOURCE_SPIO 2
+#define AEU_INPUTS_ATTN_BITS_ATC_HW_INTERRUPT (0x1<<4)
+#define AEU_INPUTS_ATTN_BITS_ATC_PARITY_ERROR (0x1<<5)
+#define AEU_INPUTS_ATTN_BITS_BRB_HW_INTERRUPT (0x1<<19)
+#define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR (0x1<<18)
+#define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT (0x1<<31)
+#define AEU_INPUTS_ATTN_BITS_CCM_PARITY_ERROR (0x1<<30)
+#define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT (0x1<<9)
+#define AEU_INPUTS_ATTN_BITS_CDU_PARITY_ERROR (0x1<<8)
+#define AEU_INPUTS_ATTN_BITS_CFC_HW_INTERRUPT (0x1<<7)
+#define AEU_INPUTS_ATTN_BITS_CFC_PARITY_ERROR (0x1<<6)
+#define AEU_INPUTS_ATTN_BITS_CSDM_HW_INTERRUPT (0x1<<29)
+#define AEU_INPUTS_ATTN_BITS_CSDM_PARITY_ERROR (0x1<<28)
+#define AEU_INPUTS_ATTN_BITS_CSEMI_HW_INTERRUPT (0x1<<1)
+#define AEU_INPUTS_ATTN_BITS_CSEMI_PARITY_ERROR (0x1<<0)
+#define AEU_INPUTS_ATTN_BITS_DEBUG_PARITY_ERROR (0x1<<18)
+#define AEU_INPUTS_ATTN_BITS_DMAE_HW_INTERRUPT (0x1<<11)
+#define AEU_INPUTS_ATTN_BITS_DMAE_PARITY_ERROR (0x1<<10)
+#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_HW_INTERRUPT (0x1<<13)
+#define AEU_INPUTS_ATTN_BITS_DOORBELLQ_PARITY_ERROR (0x1<<12)
+#define AEU_INPUTS_ATTN_BITS_GPIO0_FUNCTION_0 (0x1<<2)
+#define AEU_INPUTS_ATTN_BITS_IGU_PARITY_ERROR (0x1<<12)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_ROM_PARITY (0x1<<28)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_SCPAD_PARITY (0x1<<31)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_RX_PARITY (0x1<<29)
+#define AEU_INPUTS_ATTN_BITS_MCP_LATCHED_UMP_TX_PARITY (0x1<<30)
+#define AEU_INPUTS_ATTN_BITS_MISC_HW_INTERRUPT (0x1<<15)
+#define AEU_INPUTS_ATTN_BITS_MISC_PARITY_ERROR (0x1<<14)
+#define AEU_INPUTS_ATTN_BITS_NIG_PARITY_ERROR (0x1<<14)
+#define AEU_INPUTS_ATTN_BITS_PARSER_PARITY_ERROR (0x1<<20)
+#define AEU_INPUTS_ATTN_BITS_PBCLIENT_HW_INTERRUPT (0x1<<31)
+#define AEU_INPUTS_ATTN_BITS_PBCLIENT_PARITY_ERROR (0x1<<30)
+#define AEU_INPUTS_ATTN_BITS_PBF_PARITY_ERROR (0x1<<0)
+#define AEU_INPUTS_ATTN_BITS_PGLUE_HW_INTERRUPT (0x1<<2)
+#define AEU_INPUTS_ATTN_BITS_PGLUE_PARITY_ERROR (0x1<<3)
+#define AEU_INPUTS_ATTN_BITS_PXPPCICLOCKCLIENT_HW_INTERRUPT (0x1<<5)
+#define AEU_INPUTS_ATTN_BITS_PXPPCICLOCKCLIENT_PARITY_ERROR (0x1<<4)
+#define AEU_INPUTS_ATTN_BITS_PXP_HW_INTERRUPT (0x1<<3)
+#define AEU_INPUTS_ATTN_BITS_PXP_PARITY_ERROR (0x1<<2)
+#define AEU_INPUTS_ATTN_BITS_QM_HW_INTERRUPT (0x1<<3)
+#define AEU_INPUTS_ATTN_BITS_QM_PARITY_ERROR (0x1<<2)
+#define AEU_INPUTS_ATTN_BITS_SEARCHER_PARITY_ERROR (0x1<<22)
+#define AEU_INPUTS_ATTN_BITS_SPIO5 (0x1<<15)
+#define AEU_INPUTS_ATTN_BITS_TCM_HW_INTERRUPT (0x1<<27)
+#define AEU_INPUTS_ATTN_BITS_TCM_PARITY_ERROR (0x1<<26)
+#define AEU_INPUTS_ATTN_BITS_TIMERS_HW_INTERRUPT (0x1<<5)
+#define AEU_INPUTS_ATTN_BITS_TIMERS_PARITY_ERROR (0x1<<4)
+#define AEU_INPUTS_ATTN_BITS_TSDM_HW_INTERRUPT (0x1<<25)
+#define AEU_INPUTS_ATTN_BITS_TSDM_PARITY_ERROR (0x1<<24)
+#define AEU_INPUTS_ATTN_BITS_TSEMI_HW_INTERRUPT (0x1<<29)
+#define AEU_INPUTS_ATTN_BITS_TSEMI_PARITY_ERROR (0x1<<28)
+#define AEU_INPUTS_ATTN_BITS_UCM_HW_INTERRUPT (0x1<<23)
+#define AEU_INPUTS_ATTN_BITS_UCM_PARITY_ERROR (0x1<<22)
+#define AEU_INPUTS_ATTN_BITS_UPB_HW_INTERRUPT (0x1<<27)
+#define AEU_INPUTS_ATTN_BITS_UPB_PARITY_ERROR (0x1<<26)
+#define AEU_INPUTS_ATTN_BITS_USDM_HW_INTERRUPT (0x1<<21)
+#define AEU_INPUTS_ATTN_BITS_USDM_PARITY_ERROR (0x1<<20)
+#define AEU_INPUTS_ATTN_BITS_USEMI_HW_INTERRUPT (0x1<<25)
+#define AEU_INPUTS_ATTN_BITS_USEMI_PARITY_ERROR (0x1<<24)
+#define AEU_INPUTS_ATTN_BITS_VAUX_PCI_CORE_PARITY_ERROR (0x1<<16)
+#define AEU_INPUTS_ATTN_BITS_XCM_HW_INTERRUPT (0x1<<9)
+#define AEU_INPUTS_ATTN_BITS_XCM_PARITY_ERROR (0x1<<8)
+#define AEU_INPUTS_ATTN_BITS_XSDM_HW_INTERRUPT (0x1<<7)
+#define AEU_INPUTS_ATTN_BITS_XSDM_PARITY_ERROR (0x1<<6)
+#define AEU_INPUTS_ATTN_BITS_XSEMI_HW_INTERRUPT (0x1<<11)
+#define AEU_INPUTS_ATTN_BITS_XSEMI_PARITY_ERROR (0x1<<10)
+
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 (0x1<<5)
+#define AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_1 (0x1<<9)
+
+#define RESERVED_GENERAL_ATTENTION_BIT_0 0
+
+#define EVEREST_GEN_ATTN_IN_USE_MASK 0x7ffe0
+#define EVEREST_LATCHED_ATTN_IN_USE_MASK 0xffe00000
+
+#define RESERVED_GENERAL_ATTENTION_BIT_6 6
+#define RESERVED_GENERAL_ATTENTION_BIT_7 7
+#define RESERVED_GENERAL_ATTENTION_BIT_8 8
+#define RESERVED_GENERAL_ATTENTION_BIT_9 9
+#define RESERVED_GENERAL_ATTENTION_BIT_10 10
+#define RESERVED_GENERAL_ATTENTION_BIT_11 11
+#define RESERVED_GENERAL_ATTENTION_BIT_12 12
+#define RESERVED_GENERAL_ATTENTION_BIT_13 13
+#define RESERVED_GENERAL_ATTENTION_BIT_14 14
+#define RESERVED_GENERAL_ATTENTION_BIT_15 15
+#define RESERVED_GENERAL_ATTENTION_BIT_16 16
+#define RESERVED_GENERAL_ATTENTION_BIT_17 17
+#define RESERVED_GENERAL_ATTENTION_BIT_18 18
+#define RESERVED_GENERAL_ATTENTION_BIT_19 19
+#define RESERVED_GENERAL_ATTENTION_BIT_20 20
+#define RESERVED_GENERAL_ATTENTION_BIT_21 21
+
+/* storm asserts attention bits */
+#define TSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_7
+#define USTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_8
+#define CSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_9
+#define XSTORM_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_10
+
+/* mcp error attention bit */
+#define MCP_FATAL_ASSERT_ATTENTION_BIT RESERVED_GENERAL_ATTENTION_BIT_11
+
+/*E1H NIG status sync attention mapped to group 4-7*/
+#define LINK_SYNC_ATTENTION_BIT_FUNC_0 RESERVED_GENERAL_ATTENTION_BIT_12
+#define LINK_SYNC_ATTENTION_BIT_FUNC_1 RESERVED_GENERAL_ATTENTION_BIT_13
+#define LINK_SYNC_ATTENTION_BIT_FUNC_2 RESERVED_GENERAL_ATTENTION_BIT_14
+#define LINK_SYNC_ATTENTION_BIT_FUNC_3 RESERVED_GENERAL_ATTENTION_BIT_15
+#define LINK_SYNC_ATTENTION_BIT_FUNC_4 RESERVED_GENERAL_ATTENTION_BIT_16
+#define LINK_SYNC_ATTENTION_BIT_FUNC_5 RESERVED_GENERAL_ATTENTION_BIT_17
+#define LINK_SYNC_ATTENTION_BIT_FUNC_6 RESERVED_GENERAL_ATTENTION_BIT_18
+#define LINK_SYNC_ATTENTION_BIT_FUNC_7 RESERVED_GENERAL_ATTENTION_BIT_19
+
+
+#define LATCHED_ATTN_RBCR 23
+#define LATCHED_ATTN_RBCT 24
+#define LATCHED_ATTN_RBCN 25
+#define LATCHED_ATTN_RBCU 26
+#define LATCHED_ATTN_RBCP 27
+#define LATCHED_ATTN_TIMEOUT_GRC 28
+#define LATCHED_ATTN_RSVD_GRC 29
+#define LATCHED_ATTN_ROM_PARITY_MCP 30
+#define LATCHED_ATTN_UM_RX_PARITY_MCP 31
+#define LATCHED_ATTN_UM_TX_PARITY_MCP 32
+#define LATCHED_ATTN_SCPAD_PARITY_MCP 33
+
+#define GENERAL_ATTEN_WORD(atten_name) ((94 + atten_name) / 32)
+#define GENERAL_ATTEN_OFFSET(atten_name)\
+ (1UL << ((94 + atten_name) % 32))
+/*
+ * This file defines GRC base address for every block.
+ * This file is included by chipsim, asm microcode and cpp microcode.
+ * These values are used in Design.xml on regBase attribute
+ * Use the base with the generated offsets of specific registers.
+ */
+
+#define GRCBASE_PXPCS 0x000000
+#define GRCBASE_PCICONFIG 0x002000
+#define GRCBASE_PCIREG 0x002400
+#define GRCBASE_EMAC0 0x008000
+#define GRCBASE_EMAC1 0x008400
+#define GRCBASE_DBU 0x008800
+#define GRCBASE_MISC 0x00A000
+#define GRCBASE_DBG 0x00C000
+#define GRCBASE_NIG 0x010000
+#define GRCBASE_XCM 0x020000
+#define GRCBASE_PRS 0x040000
+#define GRCBASE_SRCH 0x040400
+#define GRCBASE_TSDM 0x042000
+#define GRCBASE_TCM 0x050000
+#define GRCBASE_BRB1 0x060000
+#define GRCBASE_MCP 0x080000
+#define GRCBASE_UPB 0x0C1000
+#define GRCBASE_CSDM 0x0C2000
+#define GRCBASE_USDM 0x0C4000
+#define GRCBASE_CCM 0x0D0000
+#define GRCBASE_UCM 0x0E0000
+#define GRCBASE_CDU 0x101000
+#define GRCBASE_DMAE 0x102000
+#define GRCBASE_PXP 0x103000
+#define GRCBASE_CFC 0x104000
+#define GRCBASE_HC 0x108000
+#define GRCBASE_PXP2 0x120000
+#define GRCBASE_PBF 0x140000
+#define GRCBASE_UMAC0 0x160000
+#define GRCBASE_UMAC1 0x160400
+#define GRCBASE_XPB 0x161000
+#define GRCBASE_MSTAT0 0x162000
+#define GRCBASE_MSTAT1 0x162800
+#define GRCBASE_XMAC0 0x163000
+#define GRCBASE_XMAC1 0x163800
+#define GRCBASE_TIMERS 0x164000
+#define GRCBASE_XSDM 0x166000
+#define GRCBASE_QM 0x168000
+#define GRCBASE_DQ 0x170000
+#define GRCBASE_TSEM 0x180000
+#define GRCBASE_CSEM 0x200000
+#define GRCBASE_XSEM 0x280000
+#define GRCBASE_USEM 0x300000
+#define GRCBASE_MISC_AEU GRCBASE_MISC
+
+
+/* offset of configuration space in the pci core register */
+#define PCICFG_OFFSET 0x2000
+#define PCICFG_VENDOR_ID_OFFSET 0x00
+#define PCICFG_DEVICE_ID_OFFSET 0x02
+#define PCICFG_COMMAND_OFFSET 0x04
+#define PCICFG_COMMAND_IO_SPACE (1<<0)
+#define PCICFG_COMMAND_MEM_SPACE (1<<1)
+#define PCICFG_COMMAND_BUS_MASTER (1<<2)
+#define PCICFG_COMMAND_SPECIAL_CYCLES (1<<3)
+#define PCICFG_COMMAND_MWI_CYCLES (1<<4)
+#define PCICFG_COMMAND_VGA_SNOOP (1<<5)
+#define PCICFG_COMMAND_PERR_ENA (1<<6)
+#define PCICFG_COMMAND_STEPPING (1<<7)
+#define PCICFG_COMMAND_SERR_ENA (1<<8)
+#define PCICFG_COMMAND_FAST_B2B (1<<9)
+#define PCICFG_COMMAND_INT_DISABLE (1<<10)
+#define PCICFG_COMMAND_RESERVED (0x1f<<11)
+#define PCICFG_STATUS_OFFSET 0x06
+#define PCICFG_REVISION_ID_OFFSET 0x08
+#define PCICFG_REVESION_ID_MASK 0xff
+#define PCICFG_REVESION_ID_ERROR_VAL 0xff
+#define PCICFG_CACHE_LINE_SIZE 0x0c
+#define PCICFG_LATENCY_TIMER 0x0d
+#define PCICFG_BAR_1_LOW 0x10
+#define PCICFG_BAR_1_HIGH 0x14
+#define PCICFG_BAR_2_LOW 0x18
+#define PCICFG_BAR_2_HIGH 0x1c
+#define PCICFG_SUBSYSTEM_VENDOR_ID_OFFSET 0x2c
+#define PCICFG_SUBSYSTEM_ID_OFFSET 0x2e
+#define PCICFG_INT_LINE 0x3c
+#define PCICFG_INT_PIN 0x3d
+#define PCICFG_PM_CAPABILITY 0x48
+#define PCICFG_PM_CAPABILITY_VERSION (0x3<<16)
+#define PCICFG_PM_CAPABILITY_CLOCK (1<<19)
+#define PCICFG_PM_CAPABILITY_RESERVED (1<<20)
+#define PCICFG_PM_CAPABILITY_DSI (1<<21)
+#define PCICFG_PM_CAPABILITY_AUX_CURRENT (0x7<<22)
+#define PCICFG_PM_CAPABILITY_D1_SUPPORT (1<<25)
+#define PCICFG_PM_CAPABILITY_D2_SUPPORT (1<<26)
+#define PCICFG_PM_CAPABILITY_PME_IN_D0 (1<<27)
+#define PCICFG_PM_CAPABILITY_PME_IN_D1 (1<<28)
+#define PCICFG_PM_CAPABILITY_PME_IN_D2 (1<<29)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_HOT (1<<30)
+#define PCICFG_PM_CAPABILITY_PME_IN_D3_COLD (1<<31)
+#define PCICFG_PM_CSR_OFFSET 0x4c
+#define PCICFG_PM_CSR_STATE (0x3<<0)
+#define PCICFG_PM_CSR_PME_ENABLE (1<<8)
+#define PCICFG_PM_CSR_PME_STATUS (1<<15)
+#define PCICFG_MSI_CAP_ID_OFFSET 0x58
+#define PCICFG_MSI_CONTROL_ENABLE (0x1<<16)
+#define PCICFG_MSI_CONTROL_MCAP (0x7<<17)
+#define PCICFG_MSI_CONTROL_MENA (0x7<<20)
+#define PCICFG_MSI_CONTROL_64_BIT_ADDR_CAP (0x1<<23)
+#define PCICFG_MSI_CONTROL_MSI_PVMASK_CAPABLE (0x1<<24)
+#define PCICFG_GRC_ADDRESS 0x78
+#define PCICFG_GRC_DATA 0x80
+#define PCICFG_ME_REGISTER 0x98
+#define PCICFG_MSIX_CAP_ID_OFFSET 0xa0
+#define PCICFG_MSIX_CONTROL_TABLE_SIZE (0x7ff<<16)
+#define PCICFG_MSIX_CONTROL_RESERVED (0x7<<27)
+#define PCICFG_MSIX_CONTROL_FUNC_MASK (0x1<<30)
+#define PCICFG_MSIX_CONTROL_MSIX_ENABLE (0x1<<31)
+
+#define PCICFG_DEVICE_CONTROL 0xb4
+#define PCICFG_DEVICE_STATUS 0xb6
+#define PCICFG_DEVICE_STATUS_CORR_ERR_DET (1<<0)
+#define PCICFG_DEVICE_STATUS_NON_FATAL_ERR_DET (1<<1)
+#define PCICFG_DEVICE_STATUS_FATAL_ERR_DET (1<<2)
+#define PCICFG_DEVICE_STATUS_UNSUP_REQ_DET (1<<3)
+#define PCICFG_DEVICE_STATUS_AUX_PWR_DET (1<<4)
+#define PCICFG_DEVICE_STATUS_NO_PEND (1<<5)
+#define PCICFG_LINK_CONTROL 0xbc
+
+
+#define BAR_USTRORM_INTMEM 0x400000
+#define BAR_CSTRORM_INTMEM 0x410000
+#define BAR_XSTRORM_INTMEM 0x420000
+#define BAR_TSTRORM_INTMEM 0x430000
+
+/* for accessing the IGU in case of status block ACK */
+#define BAR_IGU_INTMEM 0x440000
+
+#define BAR_DOORBELL_OFFSET 0x800000
+
+#define BAR_ME_REGISTER 0x450000
+
+/* config_2 offset */
+#define GRC_CONFIG_2_SIZE_REG 0x408
+#define PCI_CONFIG_2_BAR1_SIZE (0xfL<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_DISABLED (0L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_64K (1L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_128K (2L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_256K (3L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_512K (4L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_1M (5L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_2M (6L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_4M (7L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_8M (8L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_16M (9L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_32M (10L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_64M (11L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_128M (12L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_256M (13L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_512M (14L<<0)
+#define PCI_CONFIG_2_BAR1_SIZE_1G (15L<<0)
+#define PCI_CONFIG_2_BAR1_64ENA (1L<<4)
+#define PCI_CONFIG_2_EXP_ROM_RETRY (1L<<5)
+#define PCI_CONFIG_2_CFG_CYCLE_RETRY (1L<<6)
+#define PCI_CONFIG_2_FIRST_CFG_DONE (1L<<7)
+#define PCI_CONFIG_2_EXP_ROM_SIZE (0xffL<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_DISABLED (0L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_2K (1L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_4K (2L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_8K (3L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_16K (4L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_32K (5L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_64K (6L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_128K (7L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_256K (8L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_512K (9L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_1M (10L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_2M (11L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_4M (12L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_8M (13L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_16M (14L<<8)
+#define PCI_CONFIG_2_EXP_ROM_SIZE_32M (15L<<8)
+#define PCI_CONFIG_2_BAR_PREFETCH (1L<<16)
+#define PCI_CONFIG_2_RESERVED0 (0x7fffL<<17)
+
+/* config_3 offset */
+#define GRC_CONFIG_3_SIZE_REG 0x40c
+#define PCI_CONFIG_3_STICKY_BYTE (0xffL<<0)
+#define PCI_CONFIG_3_FORCE_PME (1L<<24)
+#define PCI_CONFIG_3_PME_STATUS (1L<<25)
+#define PCI_CONFIG_3_PME_ENABLE (1L<<26)
+#define PCI_CONFIG_3_PM_STATE (0x3L<<27)
+#define PCI_CONFIG_3_VAUX_PRESET (1L<<30)
+#define PCI_CONFIG_3_PCI_POWER (1L<<31)
+
+#define GRC_BAR2_CONFIG 0x4e0
+#define PCI_CONFIG_2_BAR2_SIZE (0xfL<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_DISABLED (0L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64K (1L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128K (2L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256K (3L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512K (4L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1M (5L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_2M (6L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_4M (7L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_8M (8L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_16M (9L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_32M (10L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_64M (11L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_128M (12L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_256M (13L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_512M (14L<<0)
+#define PCI_CONFIG_2_BAR2_SIZE_1G (15L<<0)
+#define PCI_CONFIG_2_BAR2_64ENA (1L<<4)
+
+#define PCI_PM_DATA_A 0x410
+#define PCI_PM_DATA_B 0x414
+#define PCI_ID_VAL1 0x434
+#define PCI_ID_VAL2 0x438
+#define PCI_ID_VAL3 0x43c
+
+#define GRC_CONFIG_REG_VF_MSIX_CONTROL 0x61C
+#define GRC_CONFIG_REG_PF_INIT_VF 0x624
+#define GRC_CR_PF_INIT_VF_PF_FIRST_VF_NUM_MASK 0xf
+/* First VF_NUM for PF is encoded in this register.
+ * The number of VFs assigned to a PF is assumed to be a multiple of 8.
+ * Software should program these bits based on Total Number of VFs \
+ * programmed for each PF.
+ * Since registers from 0x000-0x7ff are split across functions, each PF will
+ * have the same location for the same 4 bits
+ */
+
+#define PXPCS_TL_CONTROL_5 0x814
+#define PXPCS_TL_CONTROL_5_UNKNOWNTYPE_ERR_ATTN (1 << 29) /*WC*/
+#define PXPCS_TL_CONTROL_5_BOUNDARY4K_ERR_ATTN (1 << 28) /*WC*/
+#define PXPCS_TL_CONTROL_5_MRRS_ERR_ATTN (1 << 27) /*WC*/
+#define PXPCS_TL_CONTROL_5_MPS_ERR_ATTN (1 << 26) /*WC*/
+#define PXPCS_TL_CONTROL_5_TTX_BRIDGE_FORWARD_ERR (1 << 25) /*WC*/
+#define PXPCS_TL_CONTROL_5_TTX_TXINTF_OVERFLOW (1 << 24) /*WC*/
+#define PXPCS_TL_CONTROL_5_PHY_ERR_ATTN (1 << 23) /*RO*/
+#define PXPCS_TL_CONTROL_5_DL_ERR_ATTN (1 << 22) /*RO*/
+#define PXPCS_TL_CONTROL_5_TTX_ERR_NP_TAG_IN_USE (1 << 21) /*WC*/
+#define PXPCS_TL_CONTROL_5_TRX_ERR_UNEXP_RTAG (1 << 20) /*WC*/
+#define PXPCS_TL_CONTROL_5_PRI_SIG_TARGET_ABORT1 (1 << 19) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_UNSPPORT1 (1 << 18) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_ECRC1 (1 << 17) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_MALF_TLP1 (1 << 16) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_RX_OFLOW1 (1 << 15) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_UNEXP_CPL1 (1 << 14) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_MASTER_ABRT1 (1 << 13) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_CPL_TIMEOUT1 (1 << 12) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_FC_PRTL1 (1 << 11) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_PSND_TLP1 (1 << 10) /*WC*/
+#define PXPCS_TL_CONTROL_5_PRI_SIG_TARGET_ABORT (1 << 9) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_UNSPPORT (1 << 8) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_ECRC (1 << 7) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_MALF_TLP (1 << 6) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_RX_OFLOW (1 << 5) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_UNEXP_CPL (1 << 4) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_MASTER_ABRT (1 << 3) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_CPL_TIMEOUT (1 << 2) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_FC_PRTL (1 << 1) /*WC*/
+#define PXPCS_TL_CONTROL_5_ERR_PSND_TLP (1 << 0) /*WC*/
+
+
+#define PXPCS_TL_FUNC345_STAT 0x854
+#define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT4 (1 << 29) /* WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT4\
+ (1 << 28) /* Unsupported Request Error Status in function4, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_ECRC4\
+ (1 << 27) /* ECRC Error TLP Status Status in function 4, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP4\
+ (1 << 26) /* Malformed TLP Status Status in function 4, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW4\
+ (1 << 25) /* Receiver Overflow Status Status in function 4, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL4\
+ (1 << 24) /* Unexpected Completion Status Status in function 4, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT4\
+ (1 << 23) /* Receive UR Statusin function 4. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT4\
+ (1 << 22) /* Completer Timeout Status Status in function 4, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL4\
+ (1 << 21) /* Flow Control Protocol Error Status Status in \
+ function 4, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP4\
+ (1 << 20) /* Poisoned Error Status Status in function 4, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT3 (1 << 19) /* WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT3\
+ (1 << 18) /* Unsupported Request Error Status in function3, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_ECRC3\
+ (1 << 17) /* ECRC Error TLP Status Status in function 3, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP3\
+ (1 << 16) /* Malformed TLP Status Status in function 3, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW3\
+ (1 << 15) /* Receiver Overflow Status Status in function 3, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL3\
+ (1 << 14) /* Unexpected Completion Status Status in function 3, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT3\
+ (1 << 13) /* Receive UR Statusin function 3. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT3\
+ (1 << 12) /* Completer Timeout Status Status in function 3, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL3\
+ (1 << 11) /* Flow Control Protocol Error Status Status in \
+ function 3, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP3\
+ (1 << 10) /* Poisoned Error Status Status in function 3, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_PRI_SIG_TARGET_ABORT2 (1 << 9) /* WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNSPPORT2\
+ (1 << 8) /* Unsupported Request Error Status for Function 2, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_ECRC2\
+ (1 << 7) /* ECRC Error TLP Status Status for Function 2, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_MALF_TLP2\
+ (1 << 6) /* Malformed TLP Status Status for Function 2, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_RX_OFLOW2\
+ (1 << 5) /* Receiver Overflow Status Status for Function 2, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_UNEXP_CPL2\
+ (1 << 4) /* Unexpected Completion Status Status for Function 2, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC345_STAT_ERR_MASTER_ABRT2\
+ (1 << 3) /* Receive UR Statusfor Function 2. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_CPL_TIMEOUT2\
+ (1 << 2) /* Completer Timeout Status Status for Function 2, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_FC_PRTL2\
+ (1 << 1) /* Flow Control Protocol Error Status Status for \
+ Function 2, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC345_STAT_ERR_PSND_TLP2\
+ (1 << 0) /* Poisoned Error Status Status for Function 2, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+
+
+#define PXPCS_TL_FUNC678_STAT 0x85C
+#define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT7 (1 << 29) /* WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT7\
+ (1 << 28) /* Unsupported Request Error Status in function7, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_ECRC7\
+ (1 << 27) /* ECRC Error TLP Status Status in function 7, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP7\
+ (1 << 26) /* Malformed TLP Status Status in function 7, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW7\
+ (1 << 25) /* Receiver Overflow Status Status in function 7, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL7\
+ (1 << 24) /* Unexpected Completion Status Status in function 7, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT7\
+ (1 << 23) /* Receive UR Statusin function 7. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT7\
+ (1 << 22) /* Completer Timeout Status Status in function 7, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL7\
+ (1 << 21) /* Flow Control Protocol Error Status Status in \
+ function 7, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP7\
+ (1 << 20) /* Poisoned Error Status Status in function 7, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT6 (1 << 19) /* WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT6\
+ (1 << 18) /* Unsupported Request Error Status in function6, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_ECRC6\
+ (1 << 17) /* ECRC Error TLP Status Status in function 6, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP6\
+ (1 << 16) /* Malformed TLP Status Status in function 6, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW6\
+ (1 << 15) /* Receiver Overflow Status Status in function 6, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL6\
+ (1 << 14) /* Unexpected Completion Status Status in function 6, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT6\
+ (1 << 13) /* Receive UR Statusin function 6. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT6\
+ (1 << 12) /* Completer Timeout Status Status in function 6, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL6\
+ (1 << 11) /* Flow Control Protocol Error Status Status in \
+ function 6, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP6\
+ (1 << 10) /* Poisoned Error Status Status in function 6, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_PRI_SIG_TARGET_ABORT5 (1 << 9) /* WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNSPPORT5\
+ (1 << 8) /* Unsupported Request Error Status for Function 5, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_ECRC5\
+ (1 << 7) /* ECRC Error TLP Status Status for Function 5, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_MALF_TLP5\
+ (1 << 6) /* Malformed TLP Status Status for Function 5, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_RX_OFLOW5\
+ (1 << 5) /* Receiver Overflow Status Status for Function 5, if \
+ set, generate pcie_err_attn output when this error is seen.. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_UNEXP_CPL5\
+ (1 << 4) /* Unexpected Completion Status Status for Function 5, \
+ if set, generate pcie_err_attn output when this error is seen. WC \
+ */
+#define PXPCS_TL_FUNC678_STAT_ERR_MASTER_ABRT5\
+ (1 << 3) /* Receive UR Statusfor Function 5. If set, generate \
+ pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_CPL_TIMEOUT5\
+ (1 << 2) /* Completer Timeout Status Status for Function 5, if \
+ set, generate pcie_err_attn output when this error is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_FC_PRTL5\
+ (1 << 1) /* Flow Control Protocol Error Status Status for \
+ Function 5, if set, generate pcie_err_attn output when this error \
+ is seen. WC */
+#define PXPCS_TL_FUNC678_STAT_ERR_PSND_TLP5\
+ (1 << 0) /* Poisoned Error Status Status for Function 5, if set, \
+ generate pcie_err_attn output when this error is seen.. WC */
+
+
+#define BAR_USTRORM_INTMEM 0x400000
+#define BAR_CSTRORM_INTMEM 0x410000
+#define BAR_XSTRORM_INTMEM 0x420000
+#define BAR_TSTRORM_INTMEM 0x430000
+
+/* for accessing the IGU in case of status block ACK */
+#define BAR_IGU_INTMEM 0x440000
+
+#define BAR_DOORBELL_OFFSET 0x800000
+
+#define BAR_ME_REGISTER 0x450000
+#define ME_REG_PF_NUM_SHIFT 0
+#define ME_REG_PF_NUM\
+ (7L<<ME_REG_PF_NUM_SHIFT) /* Relative PF Num */
+#define ME_REG_VF_VALID (1<<8)
+#define ME_REG_VF_NUM_SHIFT 9
+#define ME_REG_VF_NUM_MASK (0x3f<<ME_REG_VF_NUM_SHIFT)
+#define ME_REG_VF_ERR (0x1<<3)
+#define ME_REG_ABS_PF_NUM_SHIFT 16
+#define ME_REG_ABS_PF_NUM\
+ (7L<<ME_REG_ABS_PF_NUM_SHIFT) /* Absolute PF Num */
+
+
+#define PXP_VF_ADDR_IGU_START 0
+#define PXP_VF_ADDR_IGU_SIZE 0x3000
+#define PXP_VF_ADDR_IGU_END\
+ ((PXP_VF_ADDR_IGU_START) + (PXP_VF_ADDR_IGU_SIZE) - 1)
+
+#define PXP_VF_ADDR_USDM_QUEUES_START 0x3000
+#define PXP_VF_ADDR_USDM_QUEUES_SIZE\
+ (PXP_VF_ADRR_NUM_QUEUES * PXP_ADDR_QUEUE_SIZE)
+#define PXP_VF_ADDR_USDM_QUEUES_END\
+ ((PXP_VF_ADDR_USDM_QUEUES_START) + (PXP_VF_ADDR_USDM_QUEUES_SIZE) - 1)
+
+#define PXP_VF_ADDR_CSDM_GLOBAL_START 0x7600
+#define PXP_VF_ADDR_CSDM_GLOBAL_SIZE (PXP_ADDR_REG_SIZE)
+#define PXP_VF_ADDR_CSDM_GLOBAL_END\
+ ((PXP_VF_ADDR_CSDM_GLOBAL_START) + (PXP_VF_ADDR_CSDM_GLOBAL_SIZE) - 1)
+
+#define PXP_VF_ADDR_DB_START 0x7c00
+#define PXP_VF_ADDR_DB_SIZE 0x200
+#define PXP_VF_ADDR_DB_END\
+ ((PXP_VF_ADDR_DB_START) + (PXP_VF_ADDR_DB_SIZE) - 1)
+
+#define MDIO_REG_BANK_CL73_IEEEB0 0x0
+#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL 0x0
+#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN 0x0200
+#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN 0x1000
+#define MDIO_CL73_IEEEB0_CL73_AN_CONTROL_MAIN_RST 0x8000
+
+#define MDIO_REG_BANK_CL73_IEEEB1 0x10
+#define MDIO_CL73_IEEEB1_AN_ADV1 0x00
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE 0x0400
+#define MDIO_CL73_IEEEB1_AN_ADV1_ASYMMETRIC 0x0800
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_BOTH 0x0C00
+#define MDIO_CL73_IEEEB1_AN_ADV1_PAUSE_MASK 0x0C00
+#define MDIO_CL73_IEEEB1_AN_ADV2 0x01
+#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M 0x0000
+#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX 0x0020
+#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4 0x0040
+#define MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KR 0x0080
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1 0x03
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE 0x0400
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_ASYMMETRIC 0x0800
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_BOTH 0x0C00
+#define MDIO_CL73_IEEEB1_AN_LP_ADV1_PAUSE_MASK 0x0C00
+#define MDIO_CL73_IEEEB1_AN_LP_ADV2 0x04
+
+#define MDIO_REG_BANK_RX0 0x80b0
+#define MDIO_RX0_RX_STATUS 0x10
+#define MDIO_RX0_RX_STATUS_SIGDET 0x8000
+#define MDIO_RX0_RX_STATUS_RX_SEQ_DONE 0x1000
+#define MDIO_RX0_RX_EQ_BOOST 0x1c
+#define MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
+#define MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL 0x10
+
+#define MDIO_REG_BANK_RX1 0x80c0
+#define MDIO_RX1_RX_EQ_BOOST 0x1c
+#define MDIO_RX1_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
+#define MDIO_RX1_RX_EQ_BOOST_OFFSET_CTRL 0x10
+
+#define MDIO_REG_BANK_RX2 0x80d0
+#define MDIO_RX2_RX_EQ_BOOST 0x1c
+#define MDIO_RX2_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
+#define MDIO_RX2_RX_EQ_BOOST_OFFSET_CTRL 0x10
+
+#define MDIO_REG_BANK_RX3 0x80e0
+#define MDIO_RX3_RX_EQ_BOOST 0x1c
+#define MDIO_RX3_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
+#define MDIO_RX3_RX_EQ_BOOST_OFFSET_CTRL 0x10
+
+#define MDIO_REG_BANK_RX_ALL 0x80f0
+#define MDIO_RX_ALL_RX_EQ_BOOST 0x1c
+#define MDIO_RX_ALL_RX_EQ_BOOST_EQUALIZER_CTRL_MASK 0x7
+#define MDIO_RX_ALL_RX_EQ_BOOST_OFFSET_CTRL 0x10
+
+#define MDIO_REG_BANK_TX0 0x8060
+#define MDIO_TX0_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX1 0x8070
+#define MDIO_TX1_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX2 0x8080
+#define MDIO_TX2_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_TX3 0x8090
+#define MDIO_TX3_TX_DRIVER 0x17
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK 0xf000
+#define MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT 12
+#define MDIO_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_TX0_TX_DRIVER_IDRIVER_SHIFT 8
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_MASK 0x00f0
+#define MDIO_TX0_TX_DRIVER_IPREDRIVER_SHIFT 4
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_MASK 0x000e
+#define MDIO_TX0_TX_DRIVER_IFULLSPD_SHIFT 1
+#define MDIO_TX0_TX_DRIVER_ICBUF1T 1
+
+#define MDIO_REG_BANK_XGXS_BLOCK0 0x8000
+#define MDIO_BLOCK0_XGXS_CONTROL 0x10
+
+#define MDIO_REG_BANK_XGXS_BLOCK1 0x8010
+#define MDIO_BLOCK1_LANE_CTRL0 0x15
+#define MDIO_BLOCK1_LANE_CTRL1 0x16
+#define MDIO_BLOCK1_LANE_CTRL2 0x17
+#define MDIO_BLOCK1_LANE_PRBS 0x19
+
+#define MDIO_REG_BANK_XGXS_BLOCK2 0x8100
+#define MDIO_XGXS_BLOCK2_RX_LN_SWAP 0x10
+#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_ENABLE 0x8000
+#define MDIO_XGXS_BLOCK2_RX_LN_SWAP_FORCE_ENABLE 0x4000
+#define MDIO_XGXS_BLOCK2_TX_LN_SWAP 0x11
+#define MDIO_XGXS_BLOCK2_TX_LN_SWAP_ENABLE 0x8000
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G 0x14
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_CX4_XGXS 0x0001
+#define MDIO_XGXS_BLOCK2_UNICORE_MODE_10G_HIGIG_XGXS 0x0010
+#define MDIO_XGXS_BLOCK2_TEST_MODE_LANE 0x15
+
+#define MDIO_REG_BANK_GP_STATUS 0x8120
+#define MDIO_GP_STATUS_TOP_AN_STATUS1 0x1B
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_AUTONEG_COMPLETE 0x0001
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL37_AUTONEG_COMPLETE 0x0002
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_LINK_STATUS 0x0004
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_DUPLEX_STATUS 0x0008
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_MR_LP_NP_AN_ABLE 0x0010
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_CL73_LP_NP_BAM_ABLE 0x0020
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE 0x0040
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_RXSIDE 0x0080
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_MASK 0x3f00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10M 0x0000
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_100M 0x0100
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G 0x0200
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_2_5G 0x0300
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_5G 0x0400
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_6G 0x0500
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_HIG 0x0600
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_CX4 0x0700
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12G_HIG 0x0800
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_12_5G 0x0900
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_13G 0x0A00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_15G 0x0B00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_16G 0x0C00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX 0x0D00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4 0x0E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR 0x0F00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI 0x1B00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS 0x1E00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI 0x1F00
+#define MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_KR2 0x3900
+
+
+#define MDIO_REG_BANK_10G_PARALLEL_DETECT 0x8130
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS 0x10
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_STATUS_PD_LINK 0x8000
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL 0x11
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_CONTROL_PARDET10G_EN 0x1
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK 0x13
+#define MDIO_10G_PARALLEL_DETECT_PAR_DET_10G_LINK_CNT (0xb71<<1)
+
+#define MDIO_REG_BANK_SERDES_DIGITAL 0x8300
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1 0x10
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_FIBER_MODE 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_TBI_IF 0x0002
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_INVERT_SIGNAL_DETECT 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_MSTR_MODE 0x0020
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2 0x11
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_PRL_DT_EN 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_CONTROL2_AN_FST_TMR 0x0040
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1 0x14
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SGMII 0x0001
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_LINK 0x0002
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_DUPLEX 0x0004
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_MASK 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_SHIFT 3
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_2_5G 0x0018
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_1G 0x0010
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_100M 0x0008
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS1_SPEED_10M 0x0000
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS2 0x15
+#define MDIO_SERDES_DIGITAL_A_1000X_STATUS2_AN_DISABLED 0x0002
+#define MDIO_SERDES_DIGITAL_MISC1 0x18
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_MASK 0xE000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_25M 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_100M 0x2000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_125M 0x4000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M 0x6000
+#define MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_187_5M 0x8000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL 0x0010
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK 0x000f
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_2_5G 0x0000
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_5G 0x0001
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_6G 0x0002
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_HIG 0x0003
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4 0x0004
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12G 0x0005
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_12_5G 0x0006
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G 0x0007
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_15G 0x0008
+#define MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_16G 0x0009
+
+#define MDIO_REG_BANK_OVER_1G 0x8320
+#define MDIO_OVER_1G_DIGCTL_3_4 0x14
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_MASK 0xffe0
+#define MDIO_OVER_1G_DIGCTL_3_4_MP_ID_SHIFT 5
+#define MDIO_OVER_1G_UP1 0x19
+#define MDIO_OVER_1G_UP1_2_5G 0x0001
+#define MDIO_OVER_1G_UP1_5G 0x0002
+#define MDIO_OVER_1G_UP1_6G 0x0004
+#define MDIO_OVER_1G_UP1_10G 0x0010
+#define MDIO_OVER_1G_UP1_10GH 0x0008
+#define MDIO_OVER_1G_UP1_12G 0x0020
+#define MDIO_OVER_1G_UP1_12_5G 0x0040
+#define MDIO_OVER_1G_UP1_13G 0x0080
+#define MDIO_OVER_1G_UP1_15G 0x0100
+#define MDIO_OVER_1G_UP1_16G 0x0200
+#define MDIO_OVER_1G_UP2 0x1A
+#define MDIO_OVER_1G_UP2_IPREDRIVER_MASK 0x0007
+#define MDIO_OVER_1G_UP2_IDRIVER_MASK 0x0038
+#define MDIO_OVER_1G_UP2_PREEMPHASIS_MASK 0x03C0
+#define MDIO_OVER_1G_UP3 0x1B
+#define MDIO_OVER_1G_UP3_HIGIG2 0x0001
+#define MDIO_OVER_1G_LP_UP1 0x1C
+#define MDIO_OVER_1G_LP_UP2 0x1D
+#define MDIO_OVER_1G_LP_UP2_MR_ADV_OVER_1G_MASK 0x03ff
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK 0x0780
+#define MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT 7
+#define MDIO_OVER_1G_LP_UP3 0x1E
+
+#define MDIO_REG_BANK_REMOTE_PHY 0x8330
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS 0x10
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_OVER1G_MSG 0x0010
+#define MDIO_REMOTE_PHY_MISC_RX_STATUS_CL37_FSM_RECEIVED_BRCM_OUI_MSG 0x0600
+
+#define MDIO_REG_BANK_BAM_NEXT_PAGE 0x8350
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL 0x10
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE 0x0001
+#define MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN 0x0002
+
+#define MDIO_REG_BANK_CL73_USERB0 0x8370
+#define MDIO_CL73_USERB0_CL73_UCTRL 0x10
+#define MDIO_CL73_USERB0_CL73_UCTRL_USTAT1_MUXSEL 0x0002
+#define MDIO_CL73_USERB0_CL73_USTAT1 0x11
+#define MDIO_CL73_USERB0_CL73_USTAT1_LINK_STATUS_CHECK 0x0100
+#define MDIO_CL73_USERB0_CL73_USTAT1_AN_GOOD_CHECK_BAM37 0x0400
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1 0x12
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN 0x8000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN 0x4000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN 0x2000
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3 0x14
+#define MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR 0x0001
+
+#define MDIO_REG_BANK_AER_BLOCK 0xFFD0
+#define MDIO_AER_BLOCK_AER_REG 0x1E
+
+#define MDIO_REG_BANK_COMBO_IEEE0 0xFFE0
+#define MDIO_COMBO_IEEE0_MII_CONTROL 0x10
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK 0x2040
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_10 0x0000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100 0x2000
+#define MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_1000 0x0040
+#define MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX 0x0100
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN 0x0200
+#define MDIO_COMBO_IEEO_MII_CONTROL_AN_EN 0x1000
+#define MDIO_COMBO_IEEO_MII_CONTROL_LOOPBACK 0x4000
+#define MDIO_COMBO_IEEO_MII_CONTROL_RESET 0x8000
+#define MDIO_COMBO_IEEE0_MII_STATUS 0x11
+#define MDIO_COMBO_IEEE0_MII_STATUS_LINK_PASS 0x0004
+#define MDIO_COMBO_IEEE0_MII_STATUS_AUTONEG_COMPLETE 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV 0x14
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX 0x0020
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_HALF_DUPLEX 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC 0x0080
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC 0x0100
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_ADV_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1 0x15
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_NEXT_PAGE 0x8000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_ACK 0x4000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_MASK 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_NONE 0x0000
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_PAUSE_BOTH 0x0180
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_HALF_DUP_CAP 0x0040
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_FULL_DUP_CAP 0x0020
+/*WhenthelinkpartnerisinSGMIImode(bit0=1),then
+bit15=link,bit12=duplex,bits11:10=speed,bit14=acknowledge.
+Theotherbitsarereservedandshouldbezero*/
+#define MDIO_COMBO_IEEE0_AUTO_NEG_LINK_PARTNER_ABILITY1_SGMII_MODE 0x0001
+
+
+#define MDIO_PMA_DEVAD 0x1
+/*ieee*/
+#define MDIO_PMA_REG_CTRL 0x0
+#define MDIO_PMA_REG_STATUS 0x1
+#define MDIO_PMA_REG_10G_CTRL2 0x7
+#define MDIO_PMA_REG_TX_DISABLE 0x0009
+#define MDIO_PMA_REG_RX_SD 0xa
+/*bcm*/
+#define MDIO_PMA_REG_BCM_CTRL 0x0096
+#define MDIO_PMA_REG_FEC_CTRL 0x00ab
+#define MDIO_PMA_REG_PHY_IDENTIFIER 0xc800
+#define MDIO_PMA_REG_DIGITAL_CTRL 0xc808
+#define MDIO_PMA_REG_DIGITAL_STATUS 0xc809
+#define MDIO_PMA_REG_TX_POWER_DOWN 0xca02
+#define MDIO_PMA_REG_CMU_PLL_BYPASS 0xca09
+#define MDIO_PMA_REG_MISC_CTRL 0xca0a
+#define MDIO_PMA_REG_GEN_CTRL 0xca10
+#define MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP 0x0188
+#define MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET 0x018a
+#define MDIO_PMA_REG_M8051_MSGIN_REG 0xca12
+#define MDIO_PMA_REG_M8051_MSGOUT_REG 0xca13
+#define MDIO_PMA_REG_ROM_VER1 0xca19
+#define MDIO_PMA_REG_ROM_VER2 0xca1a
+#define MDIO_PMA_REG_EDC_FFE_MAIN 0xca1b
+#define MDIO_PMA_REG_PLL_BANDWIDTH 0xca1d
+#define MDIO_PMA_REG_PLL_CTRL 0xca1e
+#define MDIO_PMA_REG_MISC_CTRL0 0xca23
+#define MDIO_PMA_REG_LRM_MODE 0xca3f
+#define MDIO_PMA_REG_CDR_BANDWIDTH 0xca46
+#define MDIO_PMA_REG_MISC_CTRL1 0xca85
+
+#define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL 0x8000
+#define MDIO_PMA_REG_SFP_TWO_WIRE_CTRL_STATUS_MASK 0x000c
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IDLE 0x0000
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_COMPLETE 0x0004
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_IN_PROGRESS 0x0008
+#define MDIO_PMA_REG_SFP_TWO_WIRE_STATUS_FAILED 0x000c
+#define MDIO_PMA_REG_SFP_TWO_WIRE_BYTE_CNT 0x8002
+#define MDIO_PMA_REG_SFP_TWO_WIRE_MEM_ADDR 0x8003
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_BUF 0xc820
+#define MDIO_PMA_REG_8726_TWO_WIRE_DATA_MASK 0xff
+#define MDIO_PMA_REG_8726_TX_CTRL1 0xca01
+#define MDIO_PMA_REG_8726_TX_CTRL2 0xca05
+
+#define MDIO_PMA_REG_8727_TWO_WIRE_SLAVE_ADDR 0x8005
+#define MDIO_PMA_REG_8727_TWO_WIRE_DATA_BUF 0x8007
+#define MDIO_PMA_REG_8727_TWO_WIRE_DATA_MASK 0xff
+#define MDIO_PMA_REG_8727_TX_CTRL1 0xca02
+#define MDIO_PMA_REG_8727_TX_CTRL2 0xca05
+#define MDIO_PMA_REG_8727_PCS_OPT_CTRL 0xc808
+#define MDIO_PMA_REG_8727_GPIO_CTRL 0xc80e
+#define MDIO_PMA_REG_8727_PCS_GP 0xc842
+#define MDIO_PMA_REG_8727_OPT_CFG_REG 0xc8e4
+
+#define MDIO_AN_REG_8727_MISC_CTRL 0x8309
+
+#define MDIO_PMA_REG_8073_CHIP_REV 0xc801
+#define MDIO_PMA_REG_8073_SPEED_LINK_STATUS 0xc820
+#define MDIO_PMA_REG_8073_XAUI_WA 0xc841
+#define MDIO_PMA_REG_8073_OPT_DIGITAL_CTRL 0xcd08
+
+#define MDIO_PMA_REG_7101_RESET 0xc000
+#define MDIO_PMA_REG_7107_LED_CNTL 0xc007
+#define MDIO_PMA_REG_7107_LINK_LED_CNTL 0xc009
+#define MDIO_PMA_REG_7101_VER1 0xc026
+#define MDIO_PMA_REG_7101_VER2 0xc027
+
+#define MDIO_PMA_REG_8481_PMD_SIGNAL 0xa811
+#define MDIO_PMA_REG_8481_LED1_MASK 0xa82c
+#define MDIO_PMA_REG_8481_LED2_MASK 0xa82f
+#define MDIO_PMA_REG_8481_LED3_MASK 0xa832
+#define MDIO_PMA_REG_8481_LED3_BLINK 0xa834
+#define MDIO_PMA_REG_8481_LED5_MASK 0xa838
+#define MDIO_PMA_REG_8481_SIGNAL_MASK 0xa835
+#define MDIO_PMA_REG_8481_LINK_SIGNAL 0xa83b
+#define MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_MASK 0x800
+#define MDIO_PMA_REG_8481_LINK_SIGNAL_LED4_ENABLE_SHIFT 11
+
+
+#define MDIO_WIS_DEVAD 0x2
+/*bcm*/
+#define MDIO_WIS_REG_LASI_CNTL 0x9002
+#define MDIO_WIS_REG_LASI_STATUS 0x9005
+
+#define MDIO_PCS_DEVAD 0x3
+#define MDIO_PCS_REG_STATUS 0x0020
+#define MDIO_PCS_REG_LASI_STATUS 0x9005
+#define MDIO_PCS_REG_7101_DSP_ACCESS 0xD000
+#define MDIO_PCS_REG_7101_SPI_MUX 0xD008
+#define MDIO_PCS_REG_7101_SPI_CTRL_ADDR 0xE12A
+#define MDIO_PCS_REG_7101_SPI_RESET_BIT (5)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR 0xE02A
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_WRITE_ENABLE_CMD (6)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_BULK_ERASE_CMD (0xC7)
+#define MDIO_PCS_REG_7101_SPI_FIFO_ADDR_PAGE_PROGRAM_CMD (2)
+#define MDIO_PCS_REG_7101_SPI_BYTES_TO_TRANSFER_ADDR 0xE028
+
+
+#define MDIO_XS_DEVAD 0x4
+#define MDIO_XS_PLL_SEQUENCER 0x8000
+#define MDIO_XS_SFX7101_XGXS_TEST1 0xc00a
+
+#define MDIO_XS_8706_REG_BANK_RX0 0x80bc
+#define MDIO_XS_8706_REG_BANK_RX1 0x80cc
+#define MDIO_XS_8706_REG_BANK_RX2 0x80dc
+#define MDIO_XS_8706_REG_BANK_RX3 0x80ec
+#define MDIO_XS_8706_REG_BANK_RXA 0x80fc
+
+#define MDIO_XS_REG_8073_RX_CTRL_PCIE 0x80FA
+
+#define MDIO_AN_DEVAD 0x7
+/*ieee*/
+#define MDIO_AN_REG_CTRL 0x0000
+#define MDIO_AN_REG_STATUS 0x0001
+#define MDIO_AN_REG_STATUS_AN_COMPLETE 0x0020
+#define MDIO_AN_REG_ADV_PAUSE 0x0010
+#define MDIO_AN_REG_ADV_PAUSE_PAUSE 0x0400
+#define MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC 0x0800
+#define MDIO_AN_REG_ADV_PAUSE_BOTH 0x0C00
+#define MDIO_AN_REG_ADV_PAUSE_MASK 0x0C00
+#define MDIO_AN_REG_ADV 0x0011
+#define MDIO_AN_REG_ADV2 0x0012
+#define MDIO_AN_REG_LP_AUTO_NEG 0x0013
+#define MDIO_AN_REG_LP_AUTO_NEG2 0x0014
+#define MDIO_AN_REG_MASTER_STATUS 0x0021
+#define MDIO_AN_REG_EEE_ADV 0x003c
+#define MDIO_AN_REG_LP_EEE_ADV 0x003d
+/*bcm*/
+#define MDIO_AN_REG_LINK_STATUS 0x8304
+#define MDIO_AN_REG_CL37_CL73 0x8370
+#define MDIO_AN_REG_CL37_AN 0xffe0
+#define MDIO_AN_REG_CL37_FC_LD 0xffe4
+#define MDIO_AN_REG_CL37_FC_LP 0xffe5
+#define MDIO_AN_REG_1000T_STATUS 0xffea
+
+#define MDIO_AN_REG_8073_2_5G 0x8329
+#define MDIO_AN_REG_8073_BAM 0x8350
+
+#define MDIO_AN_REG_8481_10GBASE_T_AN_CTRL 0x0020
+#define MDIO_AN_REG_8481_LEGACY_MII_CTRL 0xffe0
+#define MDIO_AN_REG_8481_MII_CTRL_FORCE_1G 0x40
+#define MDIO_AN_REG_8481_LEGACY_MII_STATUS 0xffe1
+#define MDIO_AN_REG_8481_LEGACY_AN_ADV 0xffe4
+#define MDIO_AN_REG_8481_LEGACY_AN_EXPANSION 0xffe6
+#define MDIO_AN_REG_8481_1000T_CTRL 0xffe9
+#define MDIO_AN_REG_8481_1G_100T_EXT_CTRL 0xfff0
+#define MIDO_AN_REG_8481_EXT_CTRL_FORCE_LEDS_OFF 0x0008
+#define MDIO_AN_REG_8481_EXPANSION_REG_RD_RW 0xfff5
+#define MDIO_AN_REG_8481_EXPANSION_REG_ACCESS 0xfff7
+#define MDIO_AN_REG_8481_AUX_CTRL 0xfff8
+#define MDIO_AN_REG_8481_LEGACY_SHADOW 0xfffc
+
+/* BCM84823 only */
+#define MDIO_CTL_DEVAD 0x1e
+#define MDIO_CTL_REG_84823_MEDIA 0x401a
+#define MDIO_CTL_REG_84823_MEDIA_MAC_MASK 0x0018
+ /* These pins configure the BCM84823 interface to MAC after reset. */
+#define MDIO_CTL_REG_84823_CTRL_MAC_XFI 0x0008
+#define MDIO_CTL_REG_84823_MEDIA_MAC_XAUI_M 0x0010
+ /* These pins configure the BCM84823 interface to Line after reset. */
+#define MDIO_CTL_REG_84823_MEDIA_LINE_MASK 0x0060
+#define MDIO_CTL_REG_84823_MEDIA_LINE_XAUI_L 0x0020
+#define MDIO_CTL_REG_84823_MEDIA_LINE_XFI 0x0040
+ /* When this pin is active high during reset, 10GBASE-T core is power
+ * down, When it is active low the 10GBASE-T is power up
+ */
+#define MDIO_CTL_REG_84823_MEDIA_COPPER_CORE_DOWN 0x0080
+#define MDIO_CTL_REG_84823_MEDIA_PRIORITY_MASK 0x0100
+#define MDIO_CTL_REG_84823_MEDIA_PRIORITY_COPPER 0x0000
+#define MDIO_CTL_REG_84823_MEDIA_PRIORITY_FIBER 0x0100
+#define MDIO_CTL_REG_84823_MEDIA_FIBER_1G 0x1000
+#define MDIO_CTL_REG_84823_USER_CTRL_REG 0x4005
+#define MDIO_CTL_REG_84823_USER_CTRL_CMS 0x0080
+#define MDIO_PMA_REG_84823_CTL_SLOW_CLK_CNT_HIGH 0xa82b
+#define MDIO_PMA_REG_84823_BLINK_RATE_VAL_15P9HZ 0x2f
+#define MDIO_PMA_REG_84823_CTL_LED_CTL_1 0xa8e3
+#define MDIO_PMA_REG_84833_CTL_LED_CTL_1 0xa8ec
+#define MDIO_PMA_REG_84823_LED3_STRETCH_EN 0x0080
+
+/* BCM84833 only */
+#define MDIO_84833_TOP_CFG_FW_REV 0x400f
+#define MDIO_84833_TOP_CFG_FW_EEE 0x10b1
+#define MDIO_84833_TOP_CFG_FW_NO_EEE 0x1f81
+#define MDIO_84833_TOP_CFG_XGPHY_STRAP1 0x401a
+#define MDIO_84833_SUPER_ISOLATE 0x8000
+/* These are mailbox register set used by 84833. */
+#define MDIO_84833_TOP_CFG_SCRATCH_REG0 0x4005
+#define MDIO_84833_TOP_CFG_SCRATCH_REG1 0x4006
+#define MDIO_84833_TOP_CFG_SCRATCH_REG2 0x4007
+#define MDIO_84833_TOP_CFG_SCRATCH_REG3 0x4008
+#define MDIO_84833_TOP_CFG_SCRATCH_REG4 0x4009
+#define MDIO_84833_TOP_CFG_SCRATCH_REG26 0x4037
+#define MDIO_84833_TOP_CFG_SCRATCH_REG27 0x4038
+#define MDIO_84833_TOP_CFG_SCRATCH_REG28 0x4039
+#define MDIO_84833_TOP_CFG_SCRATCH_REG29 0x403a
+#define MDIO_84833_TOP_CFG_SCRATCH_REG30 0x403b
+#define MDIO_84833_TOP_CFG_SCRATCH_REG31 0x403c
+#define MDIO_84833_CMD_HDLR_COMMAND MDIO_84833_TOP_CFG_SCRATCH_REG0
+#define MDIO_84833_CMD_HDLR_STATUS MDIO_84833_TOP_CFG_SCRATCH_REG26
+#define MDIO_84833_CMD_HDLR_DATA1 MDIO_84833_TOP_CFG_SCRATCH_REG27
+#define MDIO_84833_CMD_HDLR_DATA2 MDIO_84833_TOP_CFG_SCRATCH_REG28
+#define MDIO_84833_CMD_HDLR_DATA3 MDIO_84833_TOP_CFG_SCRATCH_REG29
+#define MDIO_84833_CMD_HDLR_DATA4 MDIO_84833_TOP_CFG_SCRATCH_REG30
+#define MDIO_84833_CMD_HDLR_DATA5 MDIO_84833_TOP_CFG_SCRATCH_REG31
+
+/* Mailbox command set used by 84833. */
+#define PHY84833_CMD_SET_PAIR_SWAP 0x8001
+#define PHY84833_CMD_GET_EEE_MODE 0x8008
+#define PHY84833_CMD_SET_EEE_MODE 0x8009
+/* Mailbox status set used by 84833. */
+#define PHY84833_STATUS_CMD_RECEIVED 0x0001
+#define PHY84833_STATUS_CMD_IN_PROGRESS 0x0002
+#define PHY84833_STATUS_CMD_COMPLETE_PASS 0x0004
+#define PHY84833_STATUS_CMD_COMPLETE_ERROR 0x0008
+#define PHY84833_STATUS_CMD_OPEN_FOR_CMDS 0x0010
+#define PHY84833_STATUS_CMD_SYSTEM_BOOT 0x0020
+#define PHY84833_STATUS_CMD_NOT_OPEN_FOR_CMDS 0x0040
+#define PHY84833_STATUS_CMD_CLEAR_COMPLETE 0x0080
+#define PHY84833_STATUS_CMD_OPEN_OVERRIDE 0xa5a5
+
+
+/* Warpcore clause 45 addressing */
+#define MDIO_WC_DEVAD 0x3
+#define MDIO_WC_REG_IEEE0BLK_MIICNTL 0x0
+#define MDIO_WC_REG_IEEE0BLK_AUTONEGNP 0x7
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT0 0x10
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1 0x11
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT2 0x12
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_ABILITY 0x4000
+#define MDIO_WC_REG_AN_IEEE1BLK_AN_ADV2_FEC_REQ 0x8000
+#define MDIO_WC_REG_PCS_STATUS2 0x0021
+#define MDIO_WC_REG_PMD_KR_CONTROL 0x0096
+#define MDIO_WC_REG_XGXSBLK0_XGXSCONTROL 0x8000
+#define MDIO_WC_REG_XGXSBLK0_MISCCONTROL1 0x800e
+#define MDIO_WC_REG_XGXSBLK1_DESKEW 0x8010
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL0 0x8015
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL1 0x8016
+#define MDIO_WC_REG_XGXSBLK1_LANECTRL2 0x8017
+#define MDIO_WC_REG_TX0_ANA_CTRL0 0x8061
+#define MDIO_WC_REG_TX1_ANA_CTRL0 0x8071
+#define MDIO_WC_REG_TX2_ANA_CTRL0 0x8081
+#define MDIO_WC_REG_TX3_ANA_CTRL0 0x8091
+#define MDIO_WC_REG_TX0_TX_DRIVER 0x8067
+#define MDIO_WC_REG_TX0_TX_DRIVER_IFIR_OFFSET 0x01
+#define MDIO_WC_REG_TX0_TX_DRIVER_IFIR_MASK 0x000e
+#define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET 0x04
+#define MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_MASK 0x00f0
+#define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET 0x08
+#define MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_MASK 0x0f00
+#define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET 0x0c
+#define MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_MASK 0x7000
+#define MDIO_WC_REG_TX1_TX_DRIVER 0x8077
+#define MDIO_WC_REG_TX2_TX_DRIVER 0x8087
+#define MDIO_WC_REG_TX3_TX_DRIVER 0x8097
+#define MDIO_WC_REG_RX0_ANARXCONTROL1G 0x80b9
+#define MDIO_WC_REG_RX2_ANARXCONTROL1G 0x80d9
+#define MDIO_WC_REG_RX0_PCI_CTRL 0x80ba
+#define MDIO_WC_REG_RX1_PCI_CTRL 0x80ca
+#define MDIO_WC_REG_RX2_PCI_CTRL 0x80da
+#define MDIO_WC_REG_RX3_PCI_CTRL 0x80ea
+#define MDIO_WC_REG_RXB_ANA_RX_CONTROL_PCI 0x80fa
+#define MDIO_WC_REG_XGXSBLK2_UNICORE_MODE_10G 0x8104
+#define MDIO_WC_REG_XGXS_STATUS3 0x8129
+#define MDIO_WC_REG_PAR_DET_10G_STATUS 0x8130
+#define MDIO_WC_REG_PAR_DET_10G_CTRL 0x8131
+#define MDIO_WC_REG_XGXS_X2_CONTROL2 0x8141
+#define MDIO_WC_REG_XGXS_X2_CONTROL3 0x8142
+#define MDIO_WC_REG_XGXS_RX_LN_SWAP1 0x816B
+#define MDIO_WC_REG_XGXS_TX_LN_SWAP1 0x8169
+#define MDIO_WC_REG_GP2_STATUS_GP_2_0 0x81d0
+#define MDIO_WC_REG_GP2_STATUS_GP_2_1 0x81d1
+#define MDIO_WC_REG_GP2_STATUS_GP_2_2 0x81d2
+#define MDIO_WC_REG_GP2_STATUS_GP_2_3 0x81d3
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4 0x81d4
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL73_AN_CMPL 0x1000
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_AN_CMPL 0x0100
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_LP_AN_CAP 0x0010
+#define MDIO_WC_REG_GP2_STATUS_GP_2_4_CL37_AN_CAP 0x1
+#define MDIO_WC_REG_UC_INFO_B0_DEAD_TRAP 0x81EE
+#define MDIO_WC_REG_UC_INFO_B1_VERSION 0x81F0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE 0x81F2
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE0_OFFSET 0x0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_DEFAULT 0x0
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_OPT_LR 0x1
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_DAC 0x2
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_SFP_XLAUI 0x3
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_MODE_LONG_CH_6G 0x4
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE1_OFFSET 0x4
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE2_OFFSET 0x8
+#define MDIO_WC_REG_UC_INFO_B1_FIRMWARE_LANE3_OFFSET 0xc
+#define MDIO_WC_REG_UC_INFO_B1_CRC 0x81FE
+#define MDIO_WC_REG_DSC_SMC 0x8213
+#define MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0 0x821e
+#define MDIO_WC_REG_TX_FIR_TAP 0x82e2
+#define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET 0x00
+#define MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_MASK 0x000f
+#define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET 0x04
+#define MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_MASK 0x03f0
+#define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET 0x0a
+#define MDIO_WC_REG_TX_FIR_TAP_POST_TAP_MASK 0x7c00
+#define MDIO_WC_REG_TX_FIR_TAP_ENABLE 0x8000
+#define MDIO_WC_REG_CL72_USERB0_CL72_TX_FIR_TAP 0x82e2
+#define MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL 0x82e3
+#define MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL 0x82e6
+#define MDIO_WC_REG_CL72_USERB0_CL72_BR_DEF_CTRL 0x82e7
+#define MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL 0x82e8
+#define MDIO_WC_REG_CL72_USERB0_CL72_MISC4_CONTROL 0x82ec
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1 0x8300
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2 0x8301
+#define MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3 0x8302
+#define MDIO_WC_REG_SERDESDIGITAL_STATUS1000X1 0x8304
+#define MDIO_WC_REG_SERDESDIGITAL_MISC1 0x8308
+#define MDIO_WC_REG_SERDESDIGITAL_MISC2 0x8309
+#define MDIO_WC_REG_DIGITAL3_UP1 0x8329
+#define MDIO_WC_REG_DIGITAL3_LP_UP1 0x832c
+#define MDIO_WC_REG_DIGITAL4_MISC3 0x833c
+#define MDIO_WC_REG_DIGITAL4_MISC5 0x833e
+#define MDIO_WC_REG_DIGITAL5_MISC6 0x8345
+#define MDIO_WC_REG_DIGITAL5_MISC7 0x8349
+#define MDIO_WC_REG_DIGITAL5_LINK_STATUS 0x834d
+#define MDIO_WC_REG_DIGITAL5_ACTUAL_SPEED 0x834e
+#define MDIO_WC_REG_DIGITAL6_MP5_NEXTPAGECTRL 0x8350
+#define MDIO_WC_REG_CL49_USERB0_CTRL 0x8368
+#define MDIO_WC_REG_CL73_USERB0_CTRL 0x8370
+#define MDIO_WC_REG_CL73_USERB0_USTAT 0x8371
+#define MDIO_WC_REG_CL73_BAM_CTRL1 0x8372
+#define MDIO_WC_REG_CL73_BAM_CTRL2 0x8373
+#define MDIO_WC_REG_CL73_BAM_CTRL3 0x8374
+#define MDIO_WC_REG_CL73_BAM_CODE_FIELD 0x837b
+#define MDIO_WC_REG_EEE_COMBO_CONTROL0 0x8390
+#define MDIO_WC_REG_TX66_CONTROL 0x83b0
+#define MDIO_WC_REG_RX66_CONTROL 0x83c0
+#define MDIO_WC_REG_RX66_SCW0 0x83c2
+#define MDIO_WC_REG_RX66_SCW1 0x83c3
+#define MDIO_WC_REG_RX66_SCW2 0x83c4
+#define MDIO_WC_REG_RX66_SCW3 0x83c5
+#define MDIO_WC_REG_RX66_SCW0_MASK 0x83c6
+#define MDIO_WC_REG_RX66_SCW1_MASK 0x83c7
+#define MDIO_WC_REG_RX66_SCW2_MASK 0x83c8
+#define MDIO_WC_REG_RX66_SCW3_MASK 0x83c9
+#define MDIO_WC_REG_FX100_CTRL1 0x8400
+#define MDIO_WC_REG_FX100_CTRL3 0x8402
+#define MDIO_WC_REG_CL82_USERB1_TX_CTRL5 0x8436
+#define MDIO_WC_REG_CL82_USERB1_TX_CTRL6 0x8437
+#define MDIO_WC_REG_CL82_USERB1_TX_CTRL7 0x8438
+#define MDIO_WC_REG_CL82_USERB1_TX_CTRL9 0x8439
+#define MDIO_WC_REG_CL82_USERB1_RX_CTRL10 0x843a
+#define MDIO_WC_REG_CL82_USERB1_RX_CTRL11 0x843b
+#define MDIO_WC_REG_ETA_CL73_OUI1 0x8453
+#define MDIO_WC_REG_ETA_CL73_OUI2 0x8454
+#define MDIO_WC_REG_ETA_CL73_OUI3 0x8455
+#define MDIO_WC_REG_ETA_CL73_LD_BAM_CODE 0x8456
+#define MDIO_WC_REG_ETA_CL73_LD_UD_CODE 0x8457
+#define MDIO_WC_REG_MICROBLK_CMD 0xffc2
+#define MDIO_WC_REG_MICROBLK_DL_STATUS 0xffc5
+#define MDIO_WC_REG_MICROBLK_CMD3 0xffcc
+
+#define MDIO_WC_REG_AERBLK_AER 0xffde
+#define MDIO_WC_REG_COMBO_IEEE0_MIICTRL 0xffe0
+#define MDIO_WC_REG_COMBO_IEEE0_MIIISTAT 0xffe1
+
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET 0x810A
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET_RX_BITSHIFT 0
+#define MDIO_WC0_XGXS_BLK2_LANE_RESET_TX_BITSHIFT 4
+
+#define MDIO_WC0_XGXS_BLK6_XGXS_X2_CONTROL2 0x8141
+
+#define DIGITAL5_ACTUAL_SPEED_TX_MASK 0x003f
+
+/* 54618se */
+#define MDIO_REG_GPHY_PHYID_LSB 0x3
+#define MDIO_REG_GPHY_ID_54618SE 0x5cd5
+#define MDIO_REG_GPHY_CL45_ADDR_REG 0xd
+#define MDIO_REG_GPHY_CL45_DATA_REG 0xe
+#define MDIO_REG_GPHY_EEE_RESOLVED 0x803e
+#define MDIO_REG_GPHY_EXP_ACCESS_GATE 0x15
+#define MDIO_REG_GPHY_EXP_ACCESS 0x17
+#define MDIO_REG_GPHY_EXP_ACCESS_TOP 0xd00
+#define MDIO_REG_GPHY_EXP_TOP_2K_BUF 0x40
+#define MDIO_REG_GPHY_AUX_STATUS 0x19
+#define MDIO_REG_INTR_STATUS 0x1a
+#define MDIO_REG_INTR_MASK 0x1b
+#define MDIO_REG_INTR_MASK_LINK_STATUS (0x1 << 1)
+#define MDIO_REG_GPHY_SHADOW 0x1c
+#define MDIO_REG_GPHY_SHADOW_LED_SEL1 (0x0d << 10)
+#define MDIO_REG_GPHY_SHADOW_LED_SEL2 (0x0e << 10)
+#define MDIO_REG_GPHY_SHADOW_WR_ENA (0x1 << 15)
+#define MDIO_REG_GPHY_SHADOW_AUTO_DET_MED (0x1e << 10)
+#define MDIO_REG_GPHY_SHADOW_INVERT_FIB_SD (0x1 << 8)
+
+#define IGU_FUNC_BASE 0x0400
+
+#define IGU_ADDR_MSIX 0x0000
+#define IGU_ADDR_INT_ACK 0x0200
+#define IGU_ADDR_PROD_UPD 0x0201
+#define IGU_ADDR_ATTN_BITS_UPD 0x0202
+#define IGU_ADDR_ATTN_BITS_SET 0x0203
+#define IGU_ADDR_ATTN_BITS_CLR 0x0204
+#define IGU_ADDR_COALESCE_NOW 0x0205
+#define IGU_ADDR_SIMD_MASK 0x0206
+#define IGU_ADDR_SIMD_NOMASK 0x0207
+#define IGU_ADDR_MSI_CTL 0x0210
+#define IGU_ADDR_MSI_ADDR_LO 0x0211
+#define IGU_ADDR_MSI_ADDR_HI 0x0212
+#define IGU_ADDR_MSI_DATA 0x0213
+
+#define IGU_USE_REGISTER_ustorm_type_0_sb_cleanup 0
+#define IGU_USE_REGISTER_ustorm_type_1_sb_cleanup 1
+#define IGU_USE_REGISTER_cstorm_type_0_sb_cleanup 2
+#define IGU_USE_REGISTER_cstorm_type_1_sb_cleanup 3
+
+#define COMMAND_REG_INT_ACK 0x0
+#define COMMAND_REG_PROD_UPD 0x4
+#define COMMAND_REG_ATTN_BITS_UPD 0x8
+#define COMMAND_REG_ATTN_BITS_SET 0xc
+#define COMMAND_REG_ATTN_BITS_CLR 0x10
+#define COMMAND_REG_COALESCE_NOW 0x14
+#define COMMAND_REG_SIMD_MASK 0x18
+#define COMMAND_REG_SIMD_NOMASK 0x1c
+
+
+#define IGU_MEM_BASE 0x0000
+
+#define IGU_MEM_MSIX_BASE 0x0000
+#define IGU_MEM_MSIX_UPPER 0x007f
+#define IGU_MEM_MSIX_RESERVED_UPPER 0x01ff
+
+#define IGU_MEM_PBA_MSIX_BASE 0x0200
+#define IGU_MEM_PBA_MSIX_UPPER 0x0200
+
+#define IGU_CMD_BACKWARD_COMP_PROD_UPD 0x0201
+#define IGU_MEM_PBA_MSIX_RESERVED_UPPER 0x03ff
+
+#define IGU_CMD_INT_ACK_BASE 0x0400
+#define IGU_CMD_INT_ACK_UPPER\
+ (IGU_CMD_INT_ACK_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1)
+#define IGU_CMD_INT_ACK_RESERVED_UPPER 0x04ff
+
+#define IGU_CMD_E2_PROD_UPD_BASE 0x0500
+#define IGU_CMD_E2_PROD_UPD_UPPER\
+ (IGU_CMD_E2_PROD_UPD_BASE + MAX_SB_PER_PORT * NUM_OF_PORTS_PER_PATH - 1)
+#define IGU_CMD_E2_PROD_UPD_RESERVED_UPPER 0x059f
+
+#define IGU_CMD_ATTN_BIT_UPD_UPPER 0x05a0
+#define IGU_CMD_ATTN_BIT_SET_UPPER 0x05a1
+#define IGU_CMD_ATTN_BIT_CLR_UPPER 0x05a2
+
+#define IGU_REG_SISR_MDPC_WMASK_UPPER 0x05a3
+#define IGU_REG_SISR_MDPC_WMASK_LSB_UPPER 0x05a4
+#define IGU_REG_SISR_MDPC_WMASK_MSB_UPPER 0x05a5
+#define IGU_REG_SISR_MDPC_WOMASK_UPPER 0x05a6
+
+#define IGU_REG_RESERVED_UPPER 0x05ff
+/* Fields of IGU PF CONFIGURATION REGISTER */
+#define IGU_PF_CONF_FUNC_EN (0x1<<0) /* function enable */
+#define IGU_PF_CONF_MSI_MSIX_EN (0x1<<1) /* MSI/MSIX enable */
+#define IGU_PF_CONF_INT_LINE_EN (0x1<<2) /* INT enable */
+#define IGU_PF_CONF_ATTN_BIT_EN (0x1<<3) /* attention enable */
+#define IGU_PF_CONF_SINGLE_ISR_EN (0x1<<4) /* single ISR mode enable */
+#define IGU_PF_CONF_SIMD_MODE (0x1<<5) /* simd all ones mode */
+
+/* Fields of IGU VF CONFIGURATION REGISTER */
+#define IGU_VF_CONF_FUNC_EN (0x1<<0) /* function enable */
+#define IGU_VF_CONF_MSI_MSIX_EN (0x1<<1) /* MSI/MSIX enable */
+#define IGU_VF_CONF_PARENT_MASK (0x3<<2) /* Parent PF */
+#define IGU_VF_CONF_PARENT_SHIFT 2 /* Parent PF */
+#define IGU_VF_CONF_SINGLE_ISR_EN (0x1<<4) /* single ISR mode enable */
+
+
+#define IGU_BC_DSB_NUM_SEGS 5
+#define IGU_BC_NDSB_NUM_SEGS 2
+#define IGU_NORM_DSB_NUM_SEGS 2
+#define IGU_NORM_NDSB_NUM_SEGS 1
+#define IGU_BC_BASE_DSB_PROD 128
+#define IGU_NORM_BASE_DSB_PROD 136
+
+ /* FID (if VF - [6] = 0; [5:0] = VF number; if PF - [6] = 1; \
+ [5:2] = 0; [1:0] = PF number) */
+#define IGU_FID_ENCODE_IS_PF (0x1<<6)
+#define IGU_FID_ENCODE_IS_PF_SHIFT 6
+#define IGU_FID_VF_NUM_MASK (0x3f)
+#define IGU_FID_PF_NUM_MASK (0x7)
+
+#define IGU_REG_MAPPING_MEMORY_VALID (1<<0)
+#define IGU_REG_MAPPING_MEMORY_VECTOR_MASK (0x3F<<1)
+#define IGU_REG_MAPPING_MEMORY_VECTOR_SHIFT 1
+#define IGU_REG_MAPPING_MEMORY_FID_MASK (0x7F<<7)
+#define IGU_REG_MAPPING_MEMORY_FID_SHIFT 7
+
+
+#define CDU_REGION_NUMBER_XCM_AG 2
+#define CDU_REGION_NUMBER_UCM_AG 4
+
+
+/* String-to-compress [31:8] = CID (all 24 bits)
+ * String-to-compress [7:4] = Region
+ * String-to-compress [3:0] = Type
+ */
+#define CDU_VALID_DATA(_cid, _region, _type)\
+ (((_cid) << 8) | (((_region)&0xf)<<4) | (((_type)&0xf)))
+#define CDU_CRC8(_cid, _region, _type)\
+ (calc_crc8(CDU_VALID_DATA(_cid, _region, _type), 0xff))
+#define CDU_RSRVD_VALUE_TYPE_A(_cid, _region, _type)\
+ (0x80 | ((CDU_CRC8(_cid, _region, _type)) & 0x7f))
+#define CDU_RSRVD_VALUE_TYPE_B(_crc, _type)\
+ (0x80 | ((_type)&0xf << 3) | ((CDU_CRC8(_cid, _region, _type)) & 0x7))
+#define CDU_RSRVD_INVALIDATE_CONTEXT_VALUE(_val) ((_val) & ~0x80)
+
+/******************************************************************************
+ * Description:
+ * Calculates crc 8 on a word value: polynomial 0-1-2-8
+ * Code was translated from Verilog.
+ * Return:
+ *****************************************************************************/
+static inline u8 calc_crc8(u32 data, u8 crc)
+{
+ u8 D[32];
+ u8 NewCRC[8];
+ u8 C[8];
+ u8 crc_res;
+ u8 i;
+
+ /* split the data into 31 bits */
+ for (i = 0; i < 32; i++) {
+ D[i] = (u8)(data & 1);
+ data = data >> 1;
+ }
+
+ /* split the crc into 8 bits */
+ for (i = 0; i < 8; i++) {
+ C[i] = crc & 1;
+ crc = crc >> 1;
+ }
+
+ NewCRC[0] = D[31] ^ D[30] ^ D[28] ^ D[23] ^ D[21] ^ D[19] ^ D[18] ^
+ D[16] ^ D[14] ^ D[12] ^ D[8] ^ D[7] ^ D[6] ^ D[0] ^ C[4] ^
+ C[6] ^ C[7];
+ NewCRC[1] = D[30] ^ D[29] ^ D[28] ^ D[24] ^ D[23] ^ D[22] ^ D[21] ^
+ D[20] ^ D[18] ^ D[17] ^ D[16] ^ D[15] ^ D[14] ^ D[13] ^
+ D[12] ^ D[9] ^ D[6] ^ D[1] ^ D[0] ^ C[0] ^ C[4] ^ C[5] ^
+ C[6];
+ NewCRC[2] = D[29] ^ D[28] ^ D[25] ^ D[24] ^ D[22] ^ D[17] ^ D[15] ^
+ D[13] ^ D[12] ^ D[10] ^ D[8] ^ D[6] ^ D[2] ^ D[1] ^ D[0] ^
+ C[0] ^ C[1] ^ C[4] ^ C[5];
+ NewCRC[3] = D[30] ^ D[29] ^ D[26] ^ D[25] ^ D[23] ^ D[18] ^ D[16] ^
+ D[14] ^ D[13] ^ D[11] ^ D[9] ^ D[7] ^ D[3] ^ D[2] ^ D[1] ^
+ C[1] ^ C[2] ^ C[5] ^ C[6];
+ NewCRC[4] = D[31] ^ D[30] ^ D[27] ^ D[26] ^ D[24] ^ D[19] ^ D[17] ^
+ D[15] ^ D[14] ^ D[12] ^ D[10] ^ D[8] ^ D[4] ^ D[3] ^ D[2] ^
+ C[0] ^ C[2] ^ C[3] ^ C[6] ^ C[7];
+ NewCRC[5] = D[31] ^ D[28] ^ D[27] ^ D[25] ^ D[20] ^ D[18] ^ D[16] ^
+ D[15] ^ D[13] ^ D[11] ^ D[9] ^ D[5] ^ D[4] ^ D[3] ^ C[1] ^
+ C[3] ^ C[4] ^ C[7];
+ NewCRC[6] = D[29] ^ D[28] ^ D[26] ^ D[21] ^ D[19] ^ D[17] ^ D[16] ^
+ D[14] ^ D[12] ^ D[10] ^ D[6] ^ D[5] ^ D[4] ^ C[2] ^ C[4] ^
+ C[5];
+ NewCRC[7] = D[30] ^ D[29] ^ D[27] ^ D[22] ^ D[20] ^ D[18] ^ D[17] ^
+ D[15] ^ D[13] ^ D[11] ^ D[7] ^ D[6] ^ D[5] ^ C[3] ^ C[5] ^
+ C[6];
+
+ crc_res = 0;
+ for (i = 0; i < 8; i++)
+ crc_res |= (NewCRC[i] << i);
+
+ return crc_res;
+}
+
+
+#endif /* BNX2X_REG_H */
Code Review / kvmfornfv.git / blobdiff