--- /dev/null
+/*
+ * Synopsys DesignWare Multimedia Card Interface driver
+ * (Based on NXP driver for lpc 31xx)
+ *
+ * Copyright (C) 2009 NXP Semiconductors
+ * Copyright (C) 2009, 2010 Imagination Technologies Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/blkdev.h>
+#include <linux/clk.h>
+#include <linux/debugfs.h>
+#include <linux/device.h>
+#include <linux/dma-mapping.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/seq_file.h>
+#include <linux/slab.h>
+#include <linux/stat.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+#include <linux/mmc/sd.h>
+#include <linux/mmc/sdio.h>
+#include <linux/mmc/dw_mmc.h>
+#include <linux/bitops.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/mmc/slot-gpio.h>
+
+#include "dw_mmc.h"
+
+/* Common flag combinations */
+#define DW_MCI_DATA_ERROR_FLAGS (SDMMC_INT_DRTO | SDMMC_INT_DCRC | \
+ SDMMC_INT_HTO | SDMMC_INT_SBE | \
+ SDMMC_INT_EBE)
+#define DW_MCI_CMD_ERROR_FLAGS (SDMMC_INT_RTO | SDMMC_INT_RCRC | \
+ SDMMC_INT_RESP_ERR)
+#define DW_MCI_ERROR_FLAGS (DW_MCI_DATA_ERROR_FLAGS | \
+ DW_MCI_CMD_ERROR_FLAGS | SDMMC_INT_HLE)
+#define DW_MCI_SEND_STATUS 1
+#define DW_MCI_RECV_STATUS 2
+#define DW_MCI_DMA_THRESHOLD 16
+
+#define DW_MCI_FREQ_MAX 200000000 /* unit: HZ */
+#define DW_MCI_FREQ_MIN 400000 /* unit: HZ */
+
+#ifdef CONFIG_MMC_DW_IDMAC
+#define IDMAC_INT_CLR (SDMMC_IDMAC_INT_AI | SDMMC_IDMAC_INT_NI | \
+ SDMMC_IDMAC_INT_CES | SDMMC_IDMAC_INT_DU | \
+ SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
+ SDMMC_IDMAC_INT_TI)
+
+struct idmac_desc_64addr {
+ u32 des0; /* Control Descriptor */
+
+ u32 des1; /* Reserved */
+
+ u32 des2; /*Buffer sizes */
+#define IDMAC_64ADDR_SET_BUFFER1_SIZE(d, s) \
+ ((d)->des2 = ((d)->des2 & cpu_to_le32(0x03ffe000)) | \
+ ((cpu_to_le32(s)) & cpu_to_le32(0x1fff)))
+
+ u32 des3; /* Reserved */
+
+ u32 des4; /* Lower 32-bits of Buffer Address Pointer 1*/
+ u32 des5; /* Upper 32-bits of Buffer Address Pointer 1*/
+
+ u32 des6; /* Lower 32-bits of Next Descriptor Address */
+ u32 des7; /* Upper 32-bits of Next Descriptor Address */
+};
+
+struct idmac_desc {
+ __le32 des0; /* Control Descriptor */
+#define IDMAC_DES0_DIC BIT(1)
+#define IDMAC_DES0_LD BIT(2)
+#define IDMAC_DES0_FD BIT(3)
+#define IDMAC_DES0_CH BIT(4)
+#define IDMAC_DES0_ER BIT(5)
+#define IDMAC_DES0_CES BIT(30)
+#define IDMAC_DES0_OWN BIT(31)
+
+ __le32 des1; /* Buffer sizes */
+#define IDMAC_SET_BUFFER1_SIZE(d, s) \
+ ((d)->des1 = ((d)->des1 & 0x03ffe000) | ((s) & 0x1fff))
+
+ __le32 des2; /* buffer 1 physical address */
+
+ __le32 des3; /* buffer 2 physical address */
+};
+#endif /* CONFIG_MMC_DW_IDMAC */
+
+static bool dw_mci_reset(struct dw_mci *host);
+static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
+static int dw_mci_card_busy(struct mmc_host *mmc);
+
+#if defined(CONFIG_DEBUG_FS)
+static int dw_mci_req_show(struct seq_file *s, void *v)
+{
+ struct dw_mci_slot *slot = s->private;
+ struct mmc_request *mrq;
+ struct mmc_command *cmd;
+ struct mmc_command *stop;
+ struct mmc_data *data;
+
+ /* Make sure we get a consistent snapshot */
+ spin_lock_bh(&slot->host->lock);
+ mrq = slot->mrq;
+
+ if (mrq) {
+ cmd = mrq->cmd;
+ data = mrq->data;
+ stop = mrq->stop;
+
+ if (cmd)
+ seq_printf(s,
+ "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
+ cmd->opcode, cmd->arg, cmd->flags,
+ cmd->resp[0], cmd->resp[1], cmd->resp[2],
+ cmd->resp[2], cmd->error);
+ if (data)
+ seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
+ data->bytes_xfered, data->blocks,
+ data->blksz, data->flags, data->error);
+ if (stop)
+ seq_printf(s,
+ "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
+ stop->opcode, stop->arg, stop->flags,
+ stop->resp[0], stop->resp[1], stop->resp[2],
+ stop->resp[2], stop->error);
+ }
+
+ spin_unlock_bh(&slot->host->lock);
+
+ return 0;
+}
+
+static int dw_mci_req_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dw_mci_req_show, inode->i_private);
+}
+
+static const struct file_operations dw_mci_req_fops = {
+ .owner = THIS_MODULE,
+ .open = dw_mci_req_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static int dw_mci_regs_show(struct seq_file *s, void *v)
+{
+ seq_printf(s, "STATUS:\t0x%08x\n", SDMMC_STATUS);
+ seq_printf(s, "RINTSTS:\t0x%08x\n", SDMMC_RINTSTS);
+ seq_printf(s, "CMD:\t0x%08x\n", SDMMC_CMD);
+ seq_printf(s, "CTRL:\t0x%08x\n", SDMMC_CTRL);
+ seq_printf(s, "INTMASK:\t0x%08x\n", SDMMC_INTMASK);
+ seq_printf(s, "CLKENA:\t0x%08x\n", SDMMC_CLKENA);
+
+ return 0;
+}
+
+static int dw_mci_regs_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, dw_mci_regs_show, inode->i_private);
+}
+
+static const struct file_operations dw_mci_regs_fops = {
+ .owner = THIS_MODULE,
+ .open = dw_mci_regs_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
+static void dw_mci_init_debugfs(struct dw_mci_slot *slot)
+{
+ struct mmc_host *mmc = slot->mmc;
+ struct dw_mci *host = slot->host;
+ struct dentry *root;
+ struct dentry *node;
+
+ root = mmc->debugfs_root;
+ if (!root)
+ return;
+
+ node = debugfs_create_file("regs", S_IRUSR, root, host,
+ &dw_mci_regs_fops);
+ if (!node)
+ goto err;
+
+ node = debugfs_create_file("req", S_IRUSR, root, slot,
+ &dw_mci_req_fops);
+ if (!node)
+ goto err;
+
+ node = debugfs_create_u32("state", S_IRUSR, root, (u32 *)&host->state);
+ if (!node)
+ goto err;
+
+ node = debugfs_create_x32("pending_events", S_IRUSR, root,
+ (u32 *)&host->pending_events);
+ if (!node)
+ goto err;
+
+ node = debugfs_create_x32("completed_events", S_IRUSR, root,
+ (u32 *)&host->completed_events);
+ if (!node)
+ goto err;
+
+ return;
+
+err:
+ dev_err(&mmc->class_dev, "failed to initialize debugfs for slot\n");
+}
+#endif /* defined(CONFIG_DEBUG_FS) */
+
+static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg);
+
+static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd)
+{
+ struct mmc_data *data;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
+ u32 cmdr;
+ cmd->error = -EINPROGRESS;
+
+ cmdr = cmd->opcode;
+
+ if (cmd->opcode == MMC_STOP_TRANSMISSION ||
+ cmd->opcode == MMC_GO_IDLE_STATE ||
+ cmd->opcode == MMC_GO_INACTIVE_STATE ||
+ (cmd->opcode == SD_IO_RW_DIRECT &&
+ ((cmd->arg >> 9) & 0x1FFFF) == SDIO_CCCR_ABORT))
+ cmdr |= SDMMC_CMD_STOP;
+ else if (cmd->opcode != MMC_SEND_STATUS && cmd->data)
+ cmdr |= SDMMC_CMD_PRV_DAT_WAIT;
+
+ if (cmd->opcode == SD_SWITCH_VOLTAGE) {
+ u32 clk_en_a;
+
+ /* Special bit makes CMD11 not die */
+ cmdr |= SDMMC_CMD_VOLT_SWITCH;
+
+ /* Change state to continue to handle CMD11 weirdness */
+ WARN_ON(slot->host->state != STATE_SENDING_CMD);
+ slot->host->state = STATE_SENDING_CMD11;
+
+ /*
+ * We need to disable low power mode (automatic clock stop)
+ * while doing voltage switch so we don't confuse the card,
+ * since stopping the clock is a specific part of the UHS
+ * voltage change dance.
+ *
+ * Note that low power mode (SDMMC_CLKEN_LOW_PWR) will be
+ * unconditionally turned back on in dw_mci_setup_bus() if it's
+ * ever called with a non-zero clock. That shouldn't happen
+ * until the voltage change is all done.
+ */
+ clk_en_a = mci_readl(host, CLKENA);
+ clk_en_a &= ~(SDMMC_CLKEN_LOW_PWR << slot->id);
+ mci_writel(host, CLKENA, clk_en_a);
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
+ SDMMC_CMD_PRV_DAT_WAIT, 0);
+ }
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ /* We expect a response, so set this bit */
+ cmdr |= SDMMC_CMD_RESP_EXP;
+ if (cmd->flags & MMC_RSP_136)
+ cmdr |= SDMMC_CMD_RESP_LONG;
+ }
+
+ if (cmd->flags & MMC_RSP_CRC)
+ cmdr |= SDMMC_CMD_RESP_CRC;
+
+ data = cmd->data;
+ if (data) {
+ cmdr |= SDMMC_CMD_DAT_EXP;
+ if (data->flags & MMC_DATA_STREAM)
+ cmdr |= SDMMC_CMD_STRM_MODE;
+ if (data->flags & MMC_DATA_WRITE)
+ cmdr |= SDMMC_CMD_DAT_WR;
+ }
+
+ if (drv_data && drv_data->prepare_command)
+ drv_data->prepare_command(slot->host, &cmdr);
+
+ return cmdr;
+}
+
+static u32 dw_mci_prep_stop_abort(struct dw_mci *host, struct mmc_command *cmd)
+{
+ struct mmc_command *stop;
+ u32 cmdr;
+
+ if (!cmd->data)
+ return 0;
+
+ stop = &host->stop_abort;
+ cmdr = cmd->opcode;
+ memset(stop, 0, sizeof(struct mmc_command));
+
+ if (cmdr == MMC_READ_SINGLE_BLOCK ||
+ cmdr == MMC_READ_MULTIPLE_BLOCK ||
+ cmdr == MMC_WRITE_BLOCK ||
+ cmdr == MMC_WRITE_MULTIPLE_BLOCK ||
+ cmdr == MMC_SEND_TUNING_BLOCK ||
+ cmdr == MMC_SEND_TUNING_BLOCK_HS200) {
+ stop->opcode = MMC_STOP_TRANSMISSION;
+ stop->arg = 0;
+ stop->flags = MMC_RSP_R1B | MMC_CMD_AC;
+ } else if (cmdr == SD_IO_RW_EXTENDED) {
+ stop->opcode = SD_IO_RW_DIRECT;
+ stop->arg |= (1 << 31) | (0 << 28) | (SDIO_CCCR_ABORT << 9) |
+ ((cmd->arg >> 28) & 0x7);
+ stop->flags = MMC_RSP_SPI_R5 | MMC_RSP_R5 | MMC_CMD_AC;
+ } else {
+ return 0;
+ }
+
+ cmdr = stop->opcode | SDMMC_CMD_STOP |
+ SDMMC_CMD_RESP_CRC | SDMMC_CMD_RESP_EXP;
+
+ return cmdr;
+}
+
+static void dw_mci_wait_while_busy(struct dw_mci *host, u32 cmd_flags)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+
+ /*
+ * Databook says that before issuing a new data transfer command
+ * we need to check to see if the card is busy. Data transfer commands
+ * all have SDMMC_CMD_PRV_DAT_WAIT set, so we'll key off that.
+ *
+ * ...also allow sending for SDMMC_CMD_VOLT_SWITCH where busy is
+ * expected.
+ */
+ if ((cmd_flags & SDMMC_CMD_PRV_DAT_WAIT) &&
+ !(cmd_flags & SDMMC_CMD_VOLT_SWITCH)) {
+ while (mci_readl(host, STATUS) & SDMMC_STATUS_BUSY) {
+ if (time_after(jiffies, timeout)) {
+ /* Command will fail; we'll pass error then */
+ dev_err(host->dev, "Busy; trying anyway\n");
+ break;
+ }
+ udelay(10);
+ }
+ }
+}
+
+static void dw_mci_start_command(struct dw_mci *host,
+ struct mmc_command *cmd, u32 cmd_flags)
+{
+ host->cmd = cmd;
+ dev_vdbg(host->dev,
+ "start command: ARGR=0x%08x CMDR=0x%08x\n",
+ cmd->arg, cmd_flags);
+
+ mci_writel(host, CMDARG, cmd->arg);
+ wmb();
+ dw_mci_wait_while_busy(host, cmd_flags);
+
+ mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
+}
+
+static inline void send_stop_abort(struct dw_mci *host, struct mmc_data *data)
+{
+ struct mmc_command *stop = data->stop ? data->stop : &host->stop_abort;
+ dw_mci_start_command(host, stop, host->stop_cmdr);
+}
+
+/* DMA interface functions */
+static void dw_mci_stop_dma(struct dw_mci *host)
+{
+ if (host->using_dma) {
+ host->dma_ops->stop(host);
+ host->dma_ops->cleanup(host);
+ }
+
+ /* Data transfer was stopped by the interrupt handler */
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+}
+
+static int dw_mci_get_dma_dir(struct mmc_data *data)
+{
+ if (data->flags & MMC_DATA_WRITE)
+ return DMA_TO_DEVICE;
+ else
+ return DMA_FROM_DEVICE;
+}
+
+#ifdef CONFIG_MMC_DW_IDMAC
+static void dw_mci_dma_cleanup(struct dw_mci *host)
+{
+ struct mmc_data *data = host->data;
+
+ if (data)
+ if (!data->host_cookie)
+ dma_unmap_sg(host->dev,
+ data->sg,
+ data->sg_len,
+ dw_mci_get_dma_dir(data));
+}
+
+static void dw_mci_idmac_reset(struct dw_mci *host)
+{
+ u32 bmod = mci_readl(host, BMOD);
+ /* Software reset of DMA */
+ bmod |= SDMMC_IDMAC_SWRESET;
+ mci_writel(host, BMOD, bmod);
+}
+
+static void dw_mci_idmac_stop_dma(struct dw_mci *host)
+{
+ u32 temp;
+
+ /* Disable and reset the IDMAC interface */
+ temp = mci_readl(host, CTRL);
+ temp &= ~SDMMC_CTRL_USE_IDMAC;
+ temp |= SDMMC_CTRL_DMA_RESET;
+ mci_writel(host, CTRL, temp);
+
+ /* Stop the IDMAC running */
+ temp = mci_readl(host, BMOD);
+ temp &= ~(SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB);
+ temp |= SDMMC_IDMAC_SWRESET;
+ mci_writel(host, BMOD, temp);
+}
+
+static void dw_mci_idmac_complete_dma(struct dw_mci *host)
+{
+ struct mmc_data *data = host->data;
+
+ dev_vdbg(host->dev, "DMA complete\n");
+
+ host->dma_ops->cleanup(host);
+
+ /*
+ * If the card was removed, data will be NULL. No point in trying to
+ * send the stop command or waiting for NBUSY in this case.
+ */
+ if (data) {
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ }
+}
+
+static void dw_mci_translate_sglist(struct dw_mci *host, struct mmc_data *data,
+ unsigned int sg_len)
+{
+ int i;
+ if (host->dma_64bit_address == 1) {
+ struct idmac_desc_64addr *desc = host->sg_cpu;
+
+ for (i = 0; i < sg_len; i++, desc++) {
+ unsigned int length = sg_dma_len(&data->sg[i]);
+ u64 mem_addr = sg_dma_address(&data->sg[i]);
+
+ /*
+ * Set the OWN bit and disable interrupts for this
+ * descriptor
+ */
+ desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
+ IDMAC_DES0_CH;
+ /* Buffer length */
+ IDMAC_64ADDR_SET_BUFFER1_SIZE(desc, length);
+
+ /* Physical address to DMA to/from */
+ desc->des4 = mem_addr & 0xffffffff;
+ desc->des5 = mem_addr >> 32;
+ }
+
+ /* Set first descriptor */
+ desc = host->sg_cpu;
+ desc->des0 |= IDMAC_DES0_FD;
+
+ /* Set last descriptor */
+ desc = host->sg_cpu + (i - 1) *
+ sizeof(struct idmac_desc_64addr);
+ desc->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
+ desc->des0 |= IDMAC_DES0_LD;
+
+ } else {
+ struct idmac_desc *desc = host->sg_cpu;
+
+ for (i = 0; i < sg_len; i++, desc++) {
+ unsigned int length = sg_dma_len(&data->sg[i]);
+ u32 mem_addr = sg_dma_address(&data->sg[i]);
+
+ /*
+ * Set the OWN bit and disable interrupts for this
+ * descriptor
+ */
+ desc->des0 = cpu_to_le32(IDMAC_DES0_OWN |
+ IDMAC_DES0_DIC | IDMAC_DES0_CH);
+ /* Buffer length */
+ IDMAC_SET_BUFFER1_SIZE(desc, length);
+
+ /* Physical address to DMA to/from */
+ desc->des2 = cpu_to_le32(mem_addr);
+ }
+
+ /* Set first descriptor */
+ desc = host->sg_cpu;
+ desc->des0 |= cpu_to_le32(IDMAC_DES0_FD);
+
+ /* Set last descriptor */
+ desc = host->sg_cpu + (i - 1) * sizeof(struct idmac_desc);
+ desc->des0 &= cpu_to_le32(~(IDMAC_DES0_CH | IDMAC_DES0_DIC));
+ desc->des0 |= cpu_to_le32(IDMAC_DES0_LD);
+ }
+
+ wmb();
+}
+
+static void dw_mci_idmac_start_dma(struct dw_mci *host, unsigned int sg_len)
+{
+ u32 temp;
+
+ dw_mci_translate_sglist(host, host->data, sg_len);
+
+ /* Make sure to reset DMA in case we did PIO before this */
+ dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET);
+ dw_mci_idmac_reset(host);
+
+ /* Select IDMAC interface */
+ temp = mci_readl(host, CTRL);
+ temp |= SDMMC_CTRL_USE_IDMAC;
+ mci_writel(host, CTRL, temp);
+
+ wmb();
+
+ /* Enable the IDMAC */
+ temp = mci_readl(host, BMOD);
+ temp |= SDMMC_IDMAC_ENABLE | SDMMC_IDMAC_FB;
+ mci_writel(host, BMOD, temp);
+
+ /* Start it running */
+ mci_writel(host, PLDMND, 1);
+}
+
+static int dw_mci_idmac_init(struct dw_mci *host)
+{
+ int i;
+
+ if (host->dma_64bit_address == 1) {
+ struct idmac_desc_64addr *p;
+ /* Number of descriptors in the ring buffer */
+ host->ring_size = PAGE_SIZE / sizeof(struct idmac_desc_64addr);
+
+ /* Forward link the descriptor list */
+ for (i = 0, p = host->sg_cpu; i < host->ring_size - 1;
+ i++, p++) {
+ p->des6 = (host->sg_dma +
+ (sizeof(struct idmac_desc_64addr) *
+ (i + 1))) & 0xffffffff;
+
+ p->des7 = (u64)(host->sg_dma +
+ (sizeof(struct idmac_desc_64addr) *
+ (i + 1))) >> 32;
+ /* Initialize reserved and buffer size fields to "0" */
+ p->des1 = 0;
+ p->des2 = 0;
+ p->des3 = 0;
+ }
+
+ /* Set the last descriptor as the end-of-ring descriptor */
+ p->des6 = host->sg_dma & 0xffffffff;
+ p->des7 = (u64)host->sg_dma >> 32;
+ p->des0 = IDMAC_DES0_ER;
+
+ } else {
+ struct idmac_desc *p;
+ /* Number of descriptors in the ring buffer */
+ host->ring_size = PAGE_SIZE / sizeof(struct idmac_desc);
+
+ /* Forward link the descriptor list */
+ for (i = 0, p = host->sg_cpu; i < host->ring_size - 1; i++, p++) {
+ p->des3 = cpu_to_le32(host->sg_dma +
+ (sizeof(struct idmac_desc) * (i + 1)));
+ p->des1 = 0;
+ }
+
+ /* Set the last descriptor as the end-of-ring descriptor */
+ p->des3 = cpu_to_le32(host->sg_dma);
+ p->des0 = cpu_to_le32(IDMAC_DES0_ER);
+ }
+
+ dw_mci_idmac_reset(host);
+
+ if (host->dma_64bit_address == 1) {
+ /* Mask out interrupts - get Tx & Rx complete only */
+ mci_writel(host, IDSTS64, IDMAC_INT_CLR);
+ mci_writel(host, IDINTEN64, SDMMC_IDMAC_INT_NI |
+ SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
+
+ /* Set the descriptor base address */
+ mci_writel(host, DBADDRL, host->sg_dma & 0xffffffff);
+ mci_writel(host, DBADDRU, (u64)host->sg_dma >> 32);
+
+ } else {
+ /* Mask out interrupts - get Tx & Rx complete only */
+ mci_writel(host, IDSTS, IDMAC_INT_CLR);
+ mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI |
+ SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
+
+ /* Set the descriptor base address */
+ mci_writel(host, DBADDR, host->sg_dma);
+ }
+
+ return 0;
+}
+
+static const struct dw_mci_dma_ops dw_mci_idmac_ops = {
+ .init = dw_mci_idmac_init,
+ .start = dw_mci_idmac_start_dma,
+ .stop = dw_mci_idmac_stop_dma,
+ .complete = dw_mci_idmac_complete_dma,
+ .cleanup = dw_mci_dma_cleanup,
+};
+#endif /* CONFIG_MMC_DW_IDMAC */
+
+static int dw_mci_pre_dma_transfer(struct dw_mci *host,
+ struct mmc_data *data,
+ bool next)
+{
+ struct scatterlist *sg;
+ unsigned int i, sg_len;
+
+ if (!next && data->host_cookie)
+ return data->host_cookie;
+
+ /*
+ * We don't do DMA on "complex" transfers, i.e. with
+ * non-word-aligned buffers or lengths. Also, we don't bother
+ * with all the DMA setup overhead for short transfers.
+ */
+ if (data->blocks * data->blksz < DW_MCI_DMA_THRESHOLD)
+ return -EINVAL;
+
+ if (data->blksz & 3)
+ return -EINVAL;
+
+ for_each_sg(data->sg, sg, data->sg_len, i) {
+ if (sg->offset & 3 || sg->length & 3)
+ return -EINVAL;
+ }
+
+ sg_len = dma_map_sg(host->dev,
+ data->sg,
+ data->sg_len,
+ dw_mci_get_dma_dir(data));
+ if (sg_len == 0)
+ return -EINVAL;
+
+ if (next)
+ data->host_cookie = sg_len;
+
+ return sg_len;
+}
+
+static void dw_mci_pre_req(struct mmc_host *mmc,
+ struct mmc_request *mrq,
+ bool is_first_req)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct mmc_data *data = mrq->data;
+
+ if (!slot->host->use_dma || !data)
+ return;
+
+ if (data->host_cookie) {
+ data->host_cookie = 0;
+ return;
+ }
+
+ if (dw_mci_pre_dma_transfer(slot->host, mrq->data, 1) < 0)
+ data->host_cookie = 0;
+}
+
+static void dw_mci_post_req(struct mmc_host *mmc,
+ struct mmc_request *mrq,
+ int err)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct mmc_data *data = mrq->data;
+
+ if (!slot->host->use_dma || !data)
+ return;
+
+ if (data->host_cookie)
+ dma_unmap_sg(slot->host->dev,
+ data->sg,
+ data->sg_len,
+ dw_mci_get_dma_dir(data));
+ data->host_cookie = 0;
+}
+
+static void dw_mci_adjust_fifoth(struct dw_mci *host, struct mmc_data *data)
+{
+#ifdef CONFIG_MMC_DW_IDMAC
+ unsigned int blksz = data->blksz;
+ const u32 mszs[] = {1, 4, 8, 16, 32, 64, 128, 256};
+ u32 fifo_width = 1 << host->data_shift;
+ u32 blksz_depth = blksz / fifo_width, fifoth_val;
+ u32 msize = 0, rx_wmark = 1, tx_wmark, tx_wmark_invers;
+ int idx = (sizeof(mszs) / sizeof(mszs[0])) - 1;
+
+ tx_wmark = (host->fifo_depth) / 2;
+ tx_wmark_invers = host->fifo_depth - tx_wmark;
+
+ /*
+ * MSIZE is '1',
+ * if blksz is not a multiple of the FIFO width
+ */
+ if (blksz % fifo_width) {
+ msize = 0;
+ rx_wmark = 1;
+ goto done;
+ }
+
+ do {
+ if (!((blksz_depth % mszs[idx]) ||
+ (tx_wmark_invers % mszs[idx]))) {
+ msize = idx;
+ rx_wmark = mszs[idx] - 1;
+ break;
+ }
+ } while (--idx > 0);
+ /*
+ * If idx is '0', it won't be tried
+ * Thus, initial values are uesed
+ */
+done:
+ fifoth_val = SDMMC_SET_FIFOTH(msize, rx_wmark, tx_wmark);
+ mci_writel(host, FIFOTH, fifoth_val);
+#endif
+}
+
+static void dw_mci_ctrl_rd_thld(struct dw_mci *host, struct mmc_data *data)
+{
+ unsigned int blksz = data->blksz;
+ u32 blksz_depth, fifo_depth;
+ u16 thld_size;
+
+ WARN_ON(!(data->flags & MMC_DATA_READ));
+
+ /*
+ * CDTHRCTL doesn't exist prior to 240A (in fact that register offset is
+ * in the FIFO region, so we really shouldn't access it).
+ */
+ if (host->verid < DW_MMC_240A)
+ return;
+
+ if (host->timing != MMC_TIMING_MMC_HS200 &&
+ host->timing != MMC_TIMING_MMC_HS400 &&
+ host->timing != MMC_TIMING_UHS_SDR104)
+ goto disable;
+
+ blksz_depth = blksz / (1 << host->data_shift);
+ fifo_depth = host->fifo_depth;
+
+ if (blksz_depth > fifo_depth)
+ goto disable;
+
+ /*
+ * If (blksz_depth) >= (fifo_depth >> 1), should be 'thld_size <= blksz'
+ * If (blksz_depth) < (fifo_depth >> 1), should be thld_size = blksz
+ * Currently just choose blksz.
+ */
+ thld_size = blksz;
+ mci_writel(host, CDTHRCTL, SDMMC_SET_RD_THLD(thld_size, 1));
+ return;
+
+disable:
+ mci_writel(host, CDTHRCTL, SDMMC_SET_RD_THLD(0, 0));
+}
+
+static int dw_mci_submit_data_dma(struct dw_mci *host, struct mmc_data *data)
+{
+ unsigned long irqflags;
+ int sg_len;
+ u32 temp;
+
+ host->using_dma = 0;
+
+ /* If we don't have a channel, we can't do DMA */
+ if (!host->use_dma)
+ return -ENODEV;
+
+ sg_len = dw_mci_pre_dma_transfer(host, data, 0);
+ if (sg_len < 0) {
+ host->dma_ops->stop(host);
+ return sg_len;
+ }
+
+ host->using_dma = 1;
+
+ dev_vdbg(host->dev,
+ "sd sg_cpu: %#lx sg_dma: %#lx sg_len: %d\n",
+ (unsigned long)host->sg_cpu, (unsigned long)host->sg_dma,
+ sg_len);
+
+ /*
+ * Decide the MSIZE and RX/TX Watermark.
+ * If current block size is same with previous size,
+ * no need to update fifoth.
+ */
+ if (host->prev_blksz != data->blksz)
+ dw_mci_adjust_fifoth(host, data);
+
+ /* Enable the DMA interface */
+ temp = mci_readl(host, CTRL);
+ temp |= SDMMC_CTRL_DMA_ENABLE;
+ mci_writel(host, CTRL, temp);
+
+ /* Disable RX/TX IRQs, let DMA handle it */
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ temp = mci_readl(host, INTMASK);
+ temp &= ~(SDMMC_INT_RXDR | SDMMC_INT_TXDR);
+ mci_writel(host, INTMASK, temp);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+
+ host->dma_ops->start(host, sg_len);
+
+ return 0;
+}
+
+static void dw_mci_submit_data(struct dw_mci *host, struct mmc_data *data)
+{
+ unsigned long irqflags;
+ u32 temp;
+
+ data->error = -EINPROGRESS;
+
+ WARN_ON(host->data);
+ host->sg = NULL;
+ host->data = data;
+
+ if (data->flags & MMC_DATA_READ) {
+ host->dir_status = DW_MCI_RECV_STATUS;
+ dw_mci_ctrl_rd_thld(host, data);
+ } else {
+ host->dir_status = DW_MCI_SEND_STATUS;
+ }
+
+ if (dw_mci_submit_data_dma(host, data)) {
+ int flags = SG_MITER_ATOMIC;
+ if (host->data->flags & MMC_DATA_READ)
+ flags |= SG_MITER_TO_SG;
+ else
+ flags |= SG_MITER_FROM_SG;
+
+ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
+ host->sg = data->sg;
+ host->part_buf_start = 0;
+ host->part_buf_count = 0;
+
+ mci_writel(host, RINTSTS, SDMMC_INT_TXDR | SDMMC_INT_RXDR);
+
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ temp = mci_readl(host, INTMASK);
+ temp |= SDMMC_INT_TXDR | SDMMC_INT_RXDR;
+ mci_writel(host, INTMASK, temp);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+
+ temp = mci_readl(host, CTRL);
+ temp &= ~SDMMC_CTRL_DMA_ENABLE;
+ mci_writel(host, CTRL, temp);
+
+ /*
+ * Use the initial fifoth_val for PIO mode.
+ * If next issued data may be transfered by DMA mode,
+ * prev_blksz should be invalidated.
+ */
+ mci_writel(host, FIFOTH, host->fifoth_val);
+ host->prev_blksz = 0;
+ } else {
+ /*
+ * Keep the current block size.
+ * It will be used to decide whether to update
+ * fifoth register next time.
+ */
+ host->prev_blksz = data->blksz;
+ }
+}
+
+static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg)
+{
+ struct dw_mci *host = slot->host;
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+ unsigned int cmd_status = 0;
+
+ mci_writel(host, CMDARG, arg);
+ wmb();
+ dw_mci_wait_while_busy(host, cmd);
+ mci_writel(host, CMD, SDMMC_CMD_START | cmd);
+
+ while (time_before(jiffies, timeout)) {
+ cmd_status = mci_readl(host, CMD);
+ if (!(cmd_status & SDMMC_CMD_START))
+ return;
+ }
+ dev_err(&slot->mmc->class_dev,
+ "Timeout sending command (cmd %#x arg %#x status %#x)\n",
+ cmd, arg, cmd_status);
+}
+
+static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit)
+{
+ struct dw_mci *host = slot->host;
+ unsigned int clock = slot->clock;
+ u32 div;
+ u32 clk_en_a;
+ u32 sdmmc_cmd_bits = SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT;
+
+ /* We must continue to set bit 28 in CMD until the change is complete */
+ if (host->state == STATE_WAITING_CMD11_DONE)
+ sdmmc_cmd_bits |= SDMMC_CMD_VOLT_SWITCH;
+
+ if (!clock) {
+ mci_writel(host, CLKENA, 0);
+ mci_send_cmd(slot, sdmmc_cmd_bits, 0);
+ } else if (clock != host->current_speed || force_clkinit) {
+ div = host->bus_hz / clock;
+ if (host->bus_hz % clock && host->bus_hz > clock)
+ /*
+ * move the + 1 after the divide to prevent
+ * over-clocking the card.
+ */
+ div += 1;
+
+ div = (host->bus_hz != clock) ? DIV_ROUND_UP(div, 2) : 0;
+
+ if ((clock << div) != slot->__clk_old || force_clkinit)
+ dev_info(&slot->mmc->class_dev,
+ "Bus speed (slot %d) = %dHz (slot req %dHz, actual %dHZ div = %d)\n",
+ slot->id, host->bus_hz, clock,
+ div ? ((host->bus_hz / div) >> 1) :
+ host->bus_hz, div);
+
+ /* disable clock */
+ mci_writel(host, CLKENA, 0);
+ mci_writel(host, CLKSRC, 0);
+
+ /* inform CIU */
+ mci_send_cmd(slot, sdmmc_cmd_bits, 0);
+
+ /* set clock to desired speed */
+ mci_writel(host, CLKDIV, div);
+
+ /* inform CIU */
+ mci_send_cmd(slot, sdmmc_cmd_bits, 0);
+
+ /* enable clock; only low power if no SDIO */
+ clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
+ if (!test_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags))
+ clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
+ mci_writel(host, CLKENA, clk_en_a);
+
+ /* inform CIU */
+ mci_send_cmd(slot, sdmmc_cmd_bits, 0);
+
+ /* keep the clock with reflecting clock dividor */
+ slot->__clk_old = clock << div;
+ }
+
+ host->current_speed = clock;
+
+ /* Set the current slot bus width */
+ mci_writel(host, CTYPE, (slot->ctype << slot->id));
+}
+
+static void __dw_mci_start_request(struct dw_mci *host,
+ struct dw_mci_slot *slot,
+ struct mmc_command *cmd)
+{
+ struct mmc_request *mrq;
+ struct mmc_data *data;
+ u32 cmdflags;
+
+ mrq = slot->mrq;
+
+ host->cur_slot = slot;
+ host->mrq = mrq;
+
+ host->pending_events = 0;
+ host->completed_events = 0;
+ host->cmd_status = 0;
+ host->data_status = 0;
+ host->dir_status = 0;
+
+ data = cmd->data;
+ if (data) {
+ mci_writel(host, TMOUT, 0xFFFFFFFF);
+ mci_writel(host, BYTCNT, data->blksz*data->blocks);
+ mci_writel(host, BLKSIZ, data->blksz);
+ }
+
+ cmdflags = dw_mci_prepare_command(slot->mmc, cmd);
+
+ /* this is the first command, send the initialization clock */
+ if (test_and_clear_bit(DW_MMC_CARD_NEED_INIT, &slot->flags))
+ cmdflags |= SDMMC_CMD_INIT;
+
+ if (data) {
+ dw_mci_submit_data(host, data);
+ wmb();
+ }
+
+ dw_mci_start_command(host, cmd, cmdflags);
+
+ if (cmd->opcode == SD_SWITCH_VOLTAGE) {
+ unsigned long irqflags;
+
+ /*
+ * Databook says to fail after 2ms w/ no response, but evidence
+ * shows that sometimes the cmd11 interrupt takes over 130ms.
+ * We'll set to 500ms, plus an extra jiffy just in case jiffies
+ * is just about to roll over.
+ *
+ * We do this whole thing under spinlock and only if the
+ * command hasn't already completed (indicating the the irq
+ * already ran so we don't want the timeout).
+ */
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ if (!test_bit(EVENT_CMD_COMPLETE, &host->pending_events))
+ mod_timer(&host->cmd11_timer,
+ jiffies + msecs_to_jiffies(500) + 1);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+ }
+
+ if (mrq->stop)
+ host->stop_cmdr = dw_mci_prepare_command(slot->mmc, mrq->stop);
+ else
+ host->stop_cmdr = dw_mci_prep_stop_abort(host, cmd);
+}
+
+static void dw_mci_start_request(struct dw_mci *host,
+ struct dw_mci_slot *slot)
+{
+ struct mmc_request *mrq = slot->mrq;
+ struct mmc_command *cmd;
+
+ cmd = mrq->sbc ? mrq->sbc : mrq->cmd;
+ __dw_mci_start_request(host, slot, cmd);
+}
+
+/* must be called with host->lock held */
+static void dw_mci_queue_request(struct dw_mci *host, struct dw_mci_slot *slot,
+ struct mmc_request *mrq)
+{
+ dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
+ host->state);
+
+ slot->mrq = mrq;
+
+ if (host->state == STATE_WAITING_CMD11_DONE) {
+ dev_warn(&slot->mmc->class_dev,
+ "Voltage change didn't complete\n");
+ /*
+ * this case isn't expected to happen, so we can
+ * either crash here or just try to continue on
+ * in the closest possible state
+ */
+ host->state = STATE_IDLE;
+ }
+
+ if (host->state == STATE_IDLE) {
+ host->state = STATE_SENDING_CMD;
+ dw_mci_start_request(host, slot);
+ } else {
+ list_add_tail(&slot->queue_node, &host->queue);
+ }
+}
+
+static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ WARN_ON(slot->mrq);
+
+ /*
+ * The check for card presence and queueing of the request must be
+ * atomic, otherwise the card could be removed in between and the
+ * request wouldn't fail until another card was inserted.
+ */
+ spin_lock_bh(&host->lock);
+
+ if (!test_bit(DW_MMC_CARD_PRESENT, &slot->flags)) {
+ spin_unlock_bh(&host->lock);
+ mrq->cmd->error = -ENOMEDIUM;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+
+ dw_mci_queue_request(host, slot, mrq);
+
+ spin_unlock_bh(&host->lock);
+}
+
+static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ const struct dw_mci_drv_data *drv_data = slot->host->drv_data;
+ u32 regs;
+ int ret;
+
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_4:
+ slot->ctype = SDMMC_CTYPE_4BIT;
+ break;
+ case MMC_BUS_WIDTH_8:
+ slot->ctype = SDMMC_CTYPE_8BIT;
+ break;
+ default:
+ /* set default 1 bit mode */
+ slot->ctype = SDMMC_CTYPE_1BIT;
+ }
+
+ regs = mci_readl(slot->host, UHS_REG);
+
+ /* DDR mode set */
+ if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_MMC_HS400)
+ regs |= ((0x1 << slot->id) << 16);
+ else
+ regs &= ~((0x1 << slot->id) << 16);
+
+ mci_writel(slot->host, UHS_REG, regs);
+ slot->host->timing = ios->timing;
+
+ /*
+ * Use mirror of ios->clock to prevent race with mmc
+ * core ios update when finding the minimum.
+ */
+ slot->clock = ios->clock;
+
+ if (drv_data && drv_data->set_ios)
+ drv_data->set_ios(slot->host, ios);
+
+ switch (ios->power_mode) {
+ case MMC_POWER_UP:
+ if (!IS_ERR(mmc->supply.vmmc)) {
+ ret = mmc_regulator_set_ocr(mmc, mmc->supply.vmmc,
+ ios->vdd);
+ if (ret) {
+ dev_err(slot->host->dev,
+ "failed to enable vmmc regulator\n");
+ /*return, if failed turn on vmmc*/
+ return;
+ }
+ }
+ set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags);
+ regs = mci_readl(slot->host, PWREN);
+ regs |= (1 << slot->id);
+ mci_writel(slot->host, PWREN, regs);
+ break;
+ case MMC_POWER_ON:
+ if (!slot->host->vqmmc_enabled) {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ ret = regulator_enable(mmc->supply.vqmmc);
+ if (ret < 0)
+ dev_err(slot->host->dev,
+ "failed to enable vqmmc\n");
+ else
+ slot->host->vqmmc_enabled = true;
+
+ } else {
+ /* Keep track so we don't reset again */
+ slot->host->vqmmc_enabled = true;
+ }
+
+ /* Reset our state machine after powering on */
+ dw_mci_ctrl_reset(slot->host,
+ SDMMC_CTRL_ALL_RESET_FLAGS);
+ }
+
+ /* Adjust clock / bus width after power is up */
+ dw_mci_setup_bus(slot, false);
+
+ break;
+ case MMC_POWER_OFF:
+ /* Turn clock off before power goes down */
+ dw_mci_setup_bus(slot, false);
+
+ if (!IS_ERR(mmc->supply.vmmc))
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
+
+ if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
+ regulator_disable(mmc->supply.vqmmc);
+ slot->host->vqmmc_enabled = false;
+
+ regs = mci_readl(slot->host, PWREN);
+ regs &= ~(1 << slot->id);
+ mci_writel(slot->host, PWREN, regs);
+ break;
+ default:
+ break;
+ }
+
+ if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
+ slot->host->state = STATE_IDLE;
+}
+
+static int dw_mci_card_busy(struct mmc_host *mmc)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ u32 status;
+
+ /*
+ * Check the busy bit which is low when DAT[3:0]
+ * (the data lines) are 0000
+ */
+ status = mci_readl(slot->host, STATUS);
+
+ return !!(status & SDMMC_STATUS_BUSY);
+}
+
+static int dw_mci_switch_voltage(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ u32 uhs;
+ u32 v18 = SDMMC_UHS_18V << slot->id;
+ int min_uv, max_uv;
+ int ret;
+
+ /*
+ * Program the voltage. Note that some instances of dw_mmc may use
+ * the UHS_REG for this. For other instances (like exynos) the UHS_REG
+ * does no harm but you need to set the regulator directly. Try both.
+ */
+ uhs = mci_readl(host, UHS_REG);
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ min_uv = 2700000;
+ max_uv = 3600000;
+ uhs &= ~v18;
+ } else {
+ min_uv = 1700000;
+ max_uv = 1950000;
+ uhs |= v18;
+ }
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
+
+ if (ret) {
+ dev_dbg(&mmc->class_dev,
+ "Regulator set error %d: %d - %d\n",
+ ret, min_uv, max_uv);
+ return ret;
+ }
+ }
+ mci_writel(host, UHS_REG, uhs);
+
+ return 0;
+}
+
+static int dw_mci_get_ro(struct mmc_host *mmc)
+{
+ int read_only;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ int gpio_ro = mmc_gpio_get_ro(mmc);
+
+ /* Use platform get_ro function, else try on board write protect */
+ if ((slot->quirks & DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT) ||
+ (slot->host->quirks & DW_MCI_QUIRK_NO_WRITE_PROTECT))
+ read_only = 0;
+ else if (!IS_ERR_VALUE(gpio_ro))
+ read_only = gpio_ro;
+ else
+ read_only =
+ mci_readl(slot->host, WRTPRT) & (1 << slot->id) ? 1 : 0;
+
+ dev_dbg(&mmc->class_dev, "card is %s\n",
+ read_only ? "read-only" : "read-write");
+
+ return read_only;
+}
+
+static int dw_mci_get_cd(struct mmc_host *mmc)
+{
+ int present;
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci_board *brd = slot->host->pdata;
+ struct dw_mci *host = slot->host;
+ int gpio_cd = mmc_gpio_get_cd(mmc);
+
+ /* Use platform get_cd function, else try onboard card detect */
+ if ((brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION) ||
+ (mmc->caps & MMC_CAP_NONREMOVABLE))
+ present = 1;
+ else if (!IS_ERR_VALUE(gpio_cd))
+ present = gpio_cd;
+ else
+ present = (mci_readl(slot->host, CDETECT) & (1 << slot->id))
+ == 0 ? 1 : 0;
+
+ spin_lock_bh(&host->lock);
+ if (present) {
+ set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ dev_dbg(&mmc->class_dev, "card is present\n");
+ } else {
+ clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ dev_dbg(&mmc->class_dev, "card is not present\n");
+ }
+ spin_unlock_bh(&host->lock);
+
+ return present;
+}
+
+static void dw_mci_init_card(struct mmc_host *mmc, struct mmc_card *card)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+
+ /*
+ * Low power mode will stop the card clock when idle. According to the
+ * description of the CLKENA register we should disable low power mode
+ * for SDIO cards if we need SDIO interrupts to work.
+ */
+ if (mmc->caps & MMC_CAP_SDIO_IRQ) {
+ const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id;
+ u32 clk_en_a_old;
+ u32 clk_en_a;
+
+ clk_en_a_old = mci_readl(host, CLKENA);
+
+ if (card->type == MMC_TYPE_SDIO ||
+ card->type == MMC_TYPE_SD_COMBO) {
+ set_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
+ clk_en_a = clk_en_a_old & ~clken_low_pwr;
+ } else {
+ clear_bit(DW_MMC_CARD_NO_LOW_PWR, &slot->flags);
+ clk_en_a = clk_en_a_old | clken_low_pwr;
+ }
+
+ if (clk_en_a != clk_en_a_old) {
+ mci_writel(host, CLKENA, clk_en_a);
+ mci_send_cmd(slot, SDMMC_CMD_UPD_CLK |
+ SDMMC_CMD_PRV_DAT_WAIT, 0);
+ }
+ }
+}
+
+static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ unsigned long irqflags;
+ u32 int_mask;
+
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+
+ /* Enable/disable Slot Specific SDIO interrupt */
+ int_mask = mci_readl(host, INTMASK);
+ if (enb)
+ int_mask |= SDMMC_INT_SDIO(slot->sdio_id);
+ else
+ int_mask &= ~SDMMC_INT_SDIO(slot->sdio_id);
+ mci_writel(host, INTMASK, int_mask);
+
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+}
+
+static int dw_mci_execute_tuning(struct mmc_host *mmc, u32 opcode)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int err = -ENOSYS;
+
+ if (drv_data && drv_data->execute_tuning)
+ err = drv_data->execute_tuning(slot);
+ return err;
+}
+
+static int dw_mci_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ if (drv_data && drv_data->prepare_hs400_tuning)
+ return drv_data->prepare_hs400_tuning(host, ios);
+
+ return 0;
+}
+
+static const struct mmc_host_ops dw_mci_ops = {
+ .request = dw_mci_request,
+ .pre_req = dw_mci_pre_req,
+ .post_req = dw_mci_post_req,
+ .set_ios = dw_mci_set_ios,
+ .get_ro = dw_mci_get_ro,
+ .get_cd = dw_mci_get_cd,
+ .enable_sdio_irq = dw_mci_enable_sdio_irq,
+ .execute_tuning = dw_mci_execute_tuning,
+ .card_busy = dw_mci_card_busy,
+ .start_signal_voltage_switch = dw_mci_switch_voltage,
+ .init_card = dw_mci_init_card,
+ .prepare_hs400_tuning = dw_mci_prepare_hs400_tuning,
+};
+
+static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
+ __releases(&host->lock)
+ __acquires(&host->lock)
+{
+ struct dw_mci_slot *slot;
+ struct mmc_host *prev_mmc = host->cur_slot->mmc;
+
+ WARN_ON(host->cmd || host->data);
+
+ host->cur_slot->mrq = NULL;
+ host->mrq = NULL;
+ if (!list_empty(&host->queue)) {
+ slot = list_entry(host->queue.next,
+ struct dw_mci_slot, queue_node);
+ list_del(&slot->queue_node);
+ dev_vdbg(host->dev, "list not empty: %s is next\n",
+ mmc_hostname(slot->mmc));
+ host->state = STATE_SENDING_CMD;
+ dw_mci_start_request(host, slot);
+ } else {
+ dev_vdbg(host->dev, "list empty\n");
+
+ if (host->state == STATE_SENDING_CMD11)
+ host->state = STATE_WAITING_CMD11_DONE;
+ else
+ host->state = STATE_IDLE;
+ }
+
+ spin_unlock(&host->lock);
+ mmc_request_done(prev_mmc, mrq);
+ spin_lock(&host->lock);
+}
+
+static int dw_mci_command_complete(struct dw_mci *host, struct mmc_command *cmd)
+{
+ u32 status = host->cmd_status;
+
+ host->cmd_status = 0;
+
+ /* Read the response from the card (up to 16 bytes) */
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ if (cmd->flags & MMC_RSP_136) {
+ cmd->resp[3] = mci_readl(host, RESP0);
+ cmd->resp[2] = mci_readl(host, RESP1);
+ cmd->resp[1] = mci_readl(host, RESP2);
+ cmd->resp[0] = mci_readl(host, RESP3);
+ } else {
+ cmd->resp[0] = mci_readl(host, RESP0);
+ cmd->resp[1] = 0;
+ cmd->resp[2] = 0;
+ cmd->resp[3] = 0;
+ }
+ }
+
+ if (status & SDMMC_INT_RTO)
+ cmd->error = -ETIMEDOUT;
+ else if ((cmd->flags & MMC_RSP_CRC) && (status & SDMMC_INT_RCRC))
+ cmd->error = -EILSEQ;
+ else if (status & SDMMC_INT_RESP_ERR)
+ cmd->error = -EIO;
+ else
+ cmd->error = 0;
+
+ if (cmd->error) {
+ /* newer ip versions need a delay between retries */
+ if (host->quirks & DW_MCI_QUIRK_RETRY_DELAY)
+ mdelay(20);
+ }
+
+ return cmd->error;
+}
+
+static int dw_mci_data_complete(struct dw_mci *host, struct mmc_data *data)
+{
+ u32 status = host->data_status;
+
+ if (status & DW_MCI_DATA_ERROR_FLAGS) {
+ if (status & SDMMC_INT_DRTO) {
+ data->error = -ETIMEDOUT;
+ } else if (status & SDMMC_INT_DCRC) {
+ data->error = -EILSEQ;
+ } else if (status & SDMMC_INT_EBE) {
+ if (host->dir_status ==
+ DW_MCI_SEND_STATUS) {
+ /*
+ * No data CRC status was returned.
+ * The number of bytes transferred
+ * will be exaggerated in PIO mode.
+ */
+ data->bytes_xfered = 0;
+ data->error = -ETIMEDOUT;
+ } else if (host->dir_status ==
+ DW_MCI_RECV_STATUS) {
+ data->error = -EIO;
+ }
+ } else {
+ /* SDMMC_INT_SBE is included */
+ data->error = -EIO;
+ }
+
+ dev_dbg(host->dev, "data error, status 0x%08x\n", status);
+
+ /*
+ * After an error, there may be data lingering
+ * in the FIFO
+ */
+ dw_mci_reset(host);
+ } else {
+ data->bytes_xfered = data->blocks * data->blksz;
+ data->error = 0;
+ }
+
+ return data->error;
+}
+
+static void dw_mci_tasklet_func(unsigned long priv)
+{
+ struct dw_mci *host = (struct dw_mci *)priv;
+ struct mmc_data *data;
+ struct mmc_command *cmd;
+ struct mmc_request *mrq;
+ enum dw_mci_state state;
+ enum dw_mci_state prev_state;
+ unsigned int err;
+
+ spin_lock(&host->lock);
+
+ state = host->state;
+ data = host->data;
+ mrq = host->mrq;
+
+ do {
+ prev_state = state;
+
+ switch (state) {
+ case STATE_IDLE:
+ case STATE_WAITING_CMD11_DONE:
+ break;
+
+ case STATE_SENDING_CMD11:
+ case STATE_SENDING_CMD:
+ if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
+ &host->pending_events))
+ break;
+
+ cmd = host->cmd;
+ host->cmd = NULL;
+ set_bit(EVENT_CMD_COMPLETE, &host->completed_events);
+ err = dw_mci_command_complete(host, cmd);
+ if (cmd == mrq->sbc && !err) {
+ prev_state = state = STATE_SENDING_CMD;
+ __dw_mci_start_request(host, host->cur_slot,
+ mrq->cmd);
+ goto unlock;
+ }
+
+ if (cmd->data && err) {
+ dw_mci_stop_dma(host);
+ send_stop_abort(host, data);
+ state = STATE_SENDING_STOP;
+ break;
+ }
+
+ if (!cmd->data || err) {
+ dw_mci_request_end(host, mrq);
+ goto unlock;
+ }
+
+ prev_state = state = STATE_SENDING_DATA;
+ /* fall through */
+
+ case STATE_SENDING_DATA:
+ /*
+ * We could get a data error and never a transfer
+ * complete so we'd better check for it here.
+ *
+ * Note that we don't really care if we also got a
+ * transfer complete; stopping the DMA and sending an
+ * abort won't hurt.
+ */
+ if (test_and_clear_bit(EVENT_DATA_ERROR,
+ &host->pending_events)) {
+ dw_mci_stop_dma(host);
+ if (data->stop ||
+ !(host->data_status & (SDMMC_INT_DRTO |
+ SDMMC_INT_EBE)))
+ send_stop_abort(host, data);
+ state = STATE_DATA_ERROR;
+ break;
+ }
+
+ if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
+ &host->pending_events))
+ break;
+
+ set_bit(EVENT_XFER_COMPLETE, &host->completed_events);
+
+ /*
+ * Handle an EVENT_DATA_ERROR that might have shown up
+ * before the transfer completed. This might not have
+ * been caught by the check above because the interrupt
+ * could have gone off between the previous check and
+ * the check for transfer complete.
+ *
+ * Technically this ought not be needed assuming we
+ * get a DATA_COMPLETE eventually (we'll notice the
+ * error and end the request), but it shouldn't hurt.
+ *
+ * This has the advantage of sending the stop command.
+ */
+ if (test_and_clear_bit(EVENT_DATA_ERROR,
+ &host->pending_events)) {
+ dw_mci_stop_dma(host);
+ if (data->stop ||
+ !(host->data_status & (SDMMC_INT_DRTO |
+ SDMMC_INT_EBE)))
+ send_stop_abort(host, data);
+ state = STATE_DATA_ERROR;
+ break;
+ }
+ prev_state = state = STATE_DATA_BUSY;
+
+ /* fall through */
+
+ case STATE_DATA_BUSY:
+ if (!test_and_clear_bit(EVENT_DATA_COMPLETE,
+ &host->pending_events))
+ break;
+
+ host->data = NULL;
+ set_bit(EVENT_DATA_COMPLETE, &host->completed_events);
+ err = dw_mci_data_complete(host, data);
+
+ if (!err) {
+ if (!data->stop || mrq->sbc) {
+ if (mrq->sbc && data->stop)
+ data->stop->error = 0;
+ dw_mci_request_end(host, mrq);
+ goto unlock;
+ }
+
+ /* stop command for open-ended transfer*/
+ if (data->stop)
+ send_stop_abort(host, data);
+ } else {
+ /*
+ * If we don't have a command complete now we'll
+ * never get one since we just reset everything;
+ * better end the request.
+ *
+ * If we do have a command complete we'll fall
+ * through to the SENDING_STOP command and
+ * everything will be peachy keen.
+ */
+ if (!test_bit(EVENT_CMD_COMPLETE,
+ &host->pending_events)) {
+ host->cmd = NULL;
+ dw_mci_request_end(host, mrq);
+ goto unlock;
+ }
+ }
+
+ /*
+ * If err has non-zero,
+ * stop-abort command has been already issued.
+ */
+ prev_state = state = STATE_SENDING_STOP;
+
+ /* fall through */
+
+ case STATE_SENDING_STOP:
+ if (!test_and_clear_bit(EVENT_CMD_COMPLETE,
+ &host->pending_events))
+ break;
+
+ /* CMD error in data command */
+ if (mrq->cmd->error && mrq->data)
+ dw_mci_reset(host);
+
+ host->cmd = NULL;
+ host->data = NULL;
+
+ if (mrq->stop)
+ dw_mci_command_complete(host, mrq->stop);
+ else
+ host->cmd_status = 0;
+
+ dw_mci_request_end(host, mrq);
+ goto unlock;
+
+ case STATE_DATA_ERROR:
+ if (!test_and_clear_bit(EVENT_XFER_COMPLETE,
+ &host->pending_events))
+ break;
+
+ state = STATE_DATA_BUSY;
+ break;
+ }
+ } while (state != prev_state);
+
+ host->state = state;
+unlock:
+ spin_unlock(&host->lock);
+
+}
+
+/* push final bytes to part_buf, only use during push */
+static void dw_mci_set_part_bytes(struct dw_mci *host, void *buf, int cnt)
+{
+ memcpy((void *)&host->part_buf, buf, cnt);
+ host->part_buf_count = cnt;
+}
+
+/* append bytes to part_buf, only use during push */
+static int dw_mci_push_part_bytes(struct dw_mci *host, void *buf, int cnt)
+{
+ cnt = min(cnt, (1 << host->data_shift) - host->part_buf_count);
+ memcpy((void *)&host->part_buf + host->part_buf_count, buf, cnt);
+ host->part_buf_count += cnt;
+ return cnt;
+}
+
+/* pull first bytes from part_buf, only use during pull */
+static int dw_mci_pull_part_bytes(struct dw_mci *host, void *buf, int cnt)
+{
+ cnt = min(cnt, (int)host->part_buf_count);
+ if (cnt) {
+ memcpy(buf, (void *)&host->part_buf + host->part_buf_start,
+ cnt);
+ host->part_buf_count -= cnt;
+ host->part_buf_start += cnt;
+ }
+ return cnt;
+}
+
+/* pull final bytes from the part_buf, assuming it's just been filled */
+static void dw_mci_pull_final_bytes(struct dw_mci *host, void *buf, int cnt)
+{
+ memcpy(buf, &host->part_buf, cnt);
+ host->part_buf_start = cnt;
+ host->part_buf_count = (1 << host->data_shift) - cnt;
+}
+
+static void dw_mci_push_data16(struct dw_mci *host, void *buf, int cnt)
+{
+ struct mmc_data *data = host->data;
+ int init_cnt = cnt;
+
+ /* try and push anything in the part_buf */
+ if (unlikely(host->part_buf_count)) {
+ int len = dw_mci_push_part_bytes(host, buf, cnt);
+ buf += len;
+ cnt -= len;
+ if (host->part_buf_count == 2) {
+ mci_fifo_writew(host->fifo_reg, host->part_buf16);
+ host->part_buf_count = 0;
+ }
+ }
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x1)) {
+ while (cnt >= 2) {
+ u16 aligned_buf[64];
+ int len = min(cnt & -2, (int)sizeof(aligned_buf));
+ int items = len >> 1;
+ int i;
+ /* memcpy from input buffer into aligned buffer */
+ memcpy(aligned_buf, buf, len);
+ buf += len;
+ cnt -= len;
+ /* push data from aligned buffer into fifo */
+ for (i = 0; i < items; ++i)
+ mci_fifo_writew(host->fifo_reg, aligned_buf[i]);
+ }
+ } else
+#endif
+ {
+ u16 *pdata = buf;
+ for (; cnt >= 2; cnt -= 2)
+ mci_fifo_writew(host->fifo_reg, *pdata++);
+ buf = pdata;
+ }
+ /* put anything remaining in the part_buf */
+ if (cnt) {
+ dw_mci_set_part_bytes(host, buf, cnt);
+ /* Push data if we have reached the expected data length */
+ if ((data->bytes_xfered + init_cnt) ==
+ (data->blksz * data->blocks))
+ mci_fifo_writew(host->fifo_reg, host->part_buf16);
+ }
+}
+
+static void dw_mci_pull_data16(struct dw_mci *host, void *buf, int cnt)
+{
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x1)) {
+ while (cnt >= 2) {
+ /* pull data from fifo into aligned buffer */
+ u16 aligned_buf[64];
+ int len = min(cnt & -2, (int)sizeof(aligned_buf));
+ int items = len >> 1;
+ int i;
+ for (i = 0; i < items; ++i)
+ aligned_buf[i] = mci_fifo_readw(host->fifo_reg);
+ /* memcpy from aligned buffer into output buffer */
+ memcpy(buf, aligned_buf, len);
+ buf += len;
+ cnt -= len;
+ }
+ } else
+#endif
+ {
+ u16 *pdata = buf;
+ for (; cnt >= 2; cnt -= 2)
+ *pdata++ = mci_fifo_readw(host->fifo_reg);
+ buf = pdata;
+ }
+ if (cnt) {
+ host->part_buf16 = mci_fifo_readw(host->fifo_reg);
+ dw_mci_pull_final_bytes(host, buf, cnt);
+ }
+}
+
+static void dw_mci_push_data32(struct dw_mci *host, void *buf, int cnt)
+{
+ struct mmc_data *data = host->data;
+ int init_cnt = cnt;
+
+ /* try and push anything in the part_buf */
+ if (unlikely(host->part_buf_count)) {
+ int len = dw_mci_push_part_bytes(host, buf, cnt);
+ buf += len;
+ cnt -= len;
+ if (host->part_buf_count == 4) {
+ mci_fifo_writel(host->fifo_reg, host->part_buf32);
+ host->part_buf_count = 0;
+ }
+ }
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x3)) {
+ while (cnt >= 4) {
+ u32 aligned_buf[32];
+ int len = min(cnt & -4, (int)sizeof(aligned_buf));
+ int items = len >> 2;
+ int i;
+ /* memcpy from input buffer into aligned buffer */
+ memcpy(aligned_buf, buf, len);
+ buf += len;
+ cnt -= len;
+ /* push data from aligned buffer into fifo */
+ for (i = 0; i < items; ++i)
+ mci_fifo_writel(host->fifo_reg, aligned_buf[i]);
+ }
+ } else
+#endif
+ {
+ u32 *pdata = buf;
+ for (; cnt >= 4; cnt -= 4)
+ mci_fifo_writel(host->fifo_reg, *pdata++);
+ buf = pdata;
+ }
+ /* put anything remaining in the part_buf */
+ if (cnt) {
+ dw_mci_set_part_bytes(host, buf, cnt);
+ /* Push data if we have reached the expected data length */
+ if ((data->bytes_xfered + init_cnt) ==
+ (data->blksz * data->blocks))
+ mci_fifo_writel(host->fifo_reg, host->part_buf32);
+ }
+}
+
+static void dw_mci_pull_data32(struct dw_mci *host, void *buf, int cnt)
+{
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x3)) {
+ while (cnt >= 4) {
+ /* pull data from fifo into aligned buffer */
+ u32 aligned_buf[32];
+ int len = min(cnt & -4, (int)sizeof(aligned_buf));
+ int items = len >> 2;
+ int i;
+ for (i = 0; i < items; ++i)
+ aligned_buf[i] = mci_fifo_readl(host->fifo_reg);
+ /* memcpy from aligned buffer into output buffer */
+ memcpy(buf, aligned_buf, len);
+ buf += len;
+ cnt -= len;
+ }
+ } else
+#endif
+ {
+ u32 *pdata = buf;
+ for (; cnt >= 4; cnt -= 4)
+ *pdata++ = mci_fifo_readl(host->fifo_reg);
+ buf = pdata;
+ }
+ if (cnt) {
+ host->part_buf32 = mci_fifo_readl(host->fifo_reg);
+ dw_mci_pull_final_bytes(host, buf, cnt);
+ }
+}
+
+static void dw_mci_push_data64(struct dw_mci *host, void *buf, int cnt)
+{
+ struct mmc_data *data = host->data;
+ int init_cnt = cnt;
+
+ /* try and push anything in the part_buf */
+ if (unlikely(host->part_buf_count)) {
+ int len = dw_mci_push_part_bytes(host, buf, cnt);
+ buf += len;
+ cnt -= len;
+
+ if (host->part_buf_count == 8) {
+ mci_fifo_writeq(host->fifo_reg, host->part_buf);
+ host->part_buf_count = 0;
+ }
+ }
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x7)) {
+ while (cnt >= 8) {
+ u64 aligned_buf[16];
+ int len = min(cnt & -8, (int)sizeof(aligned_buf));
+ int items = len >> 3;
+ int i;
+ /* memcpy from input buffer into aligned buffer */
+ memcpy(aligned_buf, buf, len);
+ buf += len;
+ cnt -= len;
+ /* push data from aligned buffer into fifo */
+ for (i = 0; i < items; ++i)
+ mci_fifo_writeq(host->fifo_reg, aligned_buf[i]);
+ }
+ } else
+#endif
+ {
+ u64 *pdata = buf;
+ for (; cnt >= 8; cnt -= 8)
+ mci_fifo_writeq(host->fifo_reg, *pdata++);
+ buf = pdata;
+ }
+ /* put anything remaining in the part_buf */
+ if (cnt) {
+ dw_mci_set_part_bytes(host, buf, cnt);
+ /* Push data if we have reached the expected data length */
+ if ((data->bytes_xfered + init_cnt) ==
+ (data->blksz * data->blocks))
+ mci_fifo_writeq(host->fifo_reg, host->part_buf);
+ }
+}
+
+static void dw_mci_pull_data64(struct dw_mci *host, void *buf, int cnt)
+{
+#ifndef CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
+ if (unlikely((unsigned long)buf & 0x7)) {
+ while (cnt >= 8) {
+ /* pull data from fifo into aligned buffer */
+ u64 aligned_buf[16];
+ int len = min(cnt & -8, (int)sizeof(aligned_buf));
+ int items = len >> 3;
+ int i;
+ for (i = 0; i < items; ++i)
+ aligned_buf[i] = mci_fifo_readq(host->fifo_reg);
+
+ /* memcpy from aligned buffer into output buffer */
+ memcpy(buf, aligned_buf, len);
+ buf += len;
+ cnt -= len;
+ }
+ } else
+#endif
+ {
+ u64 *pdata = buf;
+ for (; cnt >= 8; cnt -= 8)
+ *pdata++ = mci_fifo_readq(host->fifo_reg);
+ buf = pdata;
+ }
+ if (cnt) {
+ host->part_buf = mci_fifo_readq(host->fifo_reg);
+ dw_mci_pull_final_bytes(host, buf, cnt);
+ }
+}
+
+static void dw_mci_pull_data(struct dw_mci *host, void *buf, int cnt)
+{
+ int len;
+
+ /* get remaining partial bytes */
+ len = dw_mci_pull_part_bytes(host, buf, cnt);
+ if (unlikely(len == cnt))
+ return;
+ buf += len;
+ cnt -= len;
+
+ /* get the rest of the data */
+ host->pull_data(host, buf, cnt);
+}
+
+static void dw_mci_read_data_pio(struct dw_mci *host, bool dto)
+{
+ struct sg_mapping_iter *sg_miter = &host->sg_miter;
+ void *buf;
+ unsigned int offset;
+ struct mmc_data *data = host->data;
+ int shift = host->data_shift;
+ u32 status;
+ unsigned int len;
+ unsigned int remain, fcnt;
+
+ do {
+ if (!sg_miter_next(sg_miter))
+ goto done;
+
+ host->sg = sg_miter->piter.sg;
+ buf = sg_miter->addr;
+ remain = sg_miter->length;
+ offset = 0;
+
+ do {
+ fcnt = (SDMMC_GET_FCNT(mci_readl(host, STATUS))
+ << shift) + host->part_buf_count;
+ len = min(remain, fcnt);
+ if (!len)
+ break;
+ dw_mci_pull_data(host, (void *)(buf + offset), len);
+ data->bytes_xfered += len;
+ offset += len;
+ remain -= len;
+ } while (remain);
+
+ sg_miter->consumed = offset;
+ status = mci_readl(host, MINTSTS);
+ mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
+ /* if the RXDR is ready read again */
+ } while ((status & SDMMC_INT_RXDR) ||
+ (dto && SDMMC_GET_FCNT(mci_readl(host, STATUS))));
+
+ if (!remain) {
+ if (!sg_miter_next(sg_miter))
+ goto done;
+ sg_miter->consumed = 0;
+ }
+ sg_miter_stop(sg_miter);
+ return;
+
+done:
+ sg_miter_stop(sg_miter);
+ host->sg = NULL;
+ smp_wmb();
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+}
+
+static void dw_mci_write_data_pio(struct dw_mci *host)
+{
+ struct sg_mapping_iter *sg_miter = &host->sg_miter;
+ void *buf;
+ unsigned int offset;
+ struct mmc_data *data = host->data;
+ int shift = host->data_shift;
+ u32 status;
+ unsigned int len;
+ unsigned int fifo_depth = host->fifo_depth;
+ unsigned int remain, fcnt;
+
+ do {
+ if (!sg_miter_next(sg_miter))
+ goto done;
+
+ host->sg = sg_miter->piter.sg;
+ buf = sg_miter->addr;
+ remain = sg_miter->length;
+ offset = 0;
+
+ do {
+ fcnt = ((fifo_depth -
+ SDMMC_GET_FCNT(mci_readl(host, STATUS)))
+ << shift) - host->part_buf_count;
+ len = min(remain, fcnt);
+ if (!len)
+ break;
+ host->push_data(host, (void *)(buf + offset), len);
+ data->bytes_xfered += len;
+ offset += len;
+ remain -= len;
+ } while (remain);
+
+ sg_miter->consumed = offset;
+ status = mci_readl(host, MINTSTS);
+ mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
+ } while (status & SDMMC_INT_TXDR); /* if TXDR write again */
+
+ if (!remain) {
+ if (!sg_miter_next(sg_miter))
+ goto done;
+ sg_miter->consumed = 0;
+ }
+ sg_miter_stop(sg_miter);
+ return;
+
+done:
+ sg_miter_stop(sg_miter);
+ host->sg = NULL;
+ smp_wmb();
+ set_bit(EVENT_XFER_COMPLETE, &host->pending_events);
+}
+
+static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status)
+{
+ if (!host->cmd_status)
+ host->cmd_status = status;
+
+ smp_wmb();
+
+ set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+}
+
+static void dw_mci_handle_cd(struct dw_mci *host)
+{
+ int i;
+
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+
+ if (!slot)
+ continue;
+
+ if (slot->mmc->ops->card_event)
+ slot->mmc->ops->card_event(slot->mmc);
+ mmc_detect_change(slot->mmc,
+ msecs_to_jiffies(host->pdata->detect_delay_ms));
+ }
+}
+
+static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
+{
+ struct dw_mci *host = dev_id;
+ u32 pending;
+ int i;
+
+ pending = mci_readl(host, MINTSTS); /* read-only mask reg */
+
+ /*
+ * DTO fix - version 2.10a and below, and only if internal DMA
+ * is configured.
+ */
+ if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO) {
+ if (!pending &&
+ ((mci_readl(host, STATUS) >> 17) & 0x1fff))
+ pending |= SDMMC_INT_DATA_OVER;
+ }
+
+ if (pending) {
+ /* Check volt switch first, since it can look like an error */
+ if ((host->state == STATE_SENDING_CMD11) &&
+ (pending & SDMMC_INT_VOLT_SWITCH)) {
+ unsigned long irqflags;
+
+ mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
+ pending &= ~SDMMC_INT_VOLT_SWITCH;
+
+ /*
+ * Hold the lock; we know cmd11_timer can't be kicked
+ * off after the lock is released, so safe to delete.
+ */
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ dw_mci_cmd_interrupt(host, pending);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+
+ del_timer(&host->cmd11_timer);
+ }
+
+ if (pending & DW_MCI_CMD_ERROR_FLAGS) {
+ mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS);
+ host->cmd_status = pending;
+ smp_wmb();
+ set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+ }
+
+ if (pending & DW_MCI_DATA_ERROR_FLAGS) {
+ /* if there is an error report DATA_ERROR */
+ mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS);
+ host->data_status = pending;
+ smp_wmb();
+ set_bit(EVENT_DATA_ERROR, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ }
+
+ if (pending & SDMMC_INT_DATA_OVER) {
+ mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER);
+ if (!host->data_status)
+ host->data_status = pending;
+ smp_wmb();
+ if (host->dir_status == DW_MCI_RECV_STATUS) {
+ if (host->sg != NULL)
+ dw_mci_read_data_pio(host, true);
+ }
+ set_bit(EVENT_DATA_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+ }
+
+ if (pending & SDMMC_INT_RXDR) {
+ mci_writel(host, RINTSTS, SDMMC_INT_RXDR);
+ if (host->dir_status == DW_MCI_RECV_STATUS && host->sg)
+ dw_mci_read_data_pio(host, false);
+ }
+
+ if (pending & SDMMC_INT_TXDR) {
+ mci_writel(host, RINTSTS, SDMMC_INT_TXDR);
+ if (host->dir_status == DW_MCI_SEND_STATUS && host->sg)
+ dw_mci_write_data_pio(host);
+ }
+
+ if (pending & SDMMC_INT_CMD_DONE) {
+ mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE);
+ dw_mci_cmd_interrupt(host, pending);
+ }
+
+ if (pending & SDMMC_INT_CD) {
+ mci_writel(host, RINTSTS, SDMMC_INT_CD);
+ dw_mci_handle_cd(host);
+ }
+
+ /* Handle SDIO Interrupts */
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+
+ if (!slot)
+ continue;
+
+ if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
+ mci_writel(host, RINTSTS,
+ SDMMC_INT_SDIO(slot->sdio_id));
+ mmc_signal_sdio_irq(slot->mmc);
+ }
+ }
+
+ }
+
+#ifdef CONFIG_MMC_DW_IDMAC
+ /* Handle DMA interrupts */
+ if (host->dma_64bit_address == 1) {
+ pending = mci_readl(host, IDSTS64);
+ if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
+ mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
+ SDMMC_IDMAC_INT_RI);
+ mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
+ host->dma_ops->complete(host);
+ }
+ } else {
+ pending = mci_readl(host, IDSTS);
+ if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
+ SDMMC_IDMAC_INT_RI);
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
+ host->dma_ops->complete(host);
+ }
+ }
+#endif
+
+ return IRQ_HANDLED;
+}
+
+#ifdef CONFIG_OF
+/* given a slot id, find out the device node representing that slot */
+static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
+{
+ struct device_node *np;
+ const __be32 *addr;
+ int len;
+
+ if (!dev || !dev->of_node)
+ return NULL;
+
+ for_each_child_of_node(dev->of_node, np) {
+ addr = of_get_property(np, "reg", &len);
+ if (!addr || (len < sizeof(int)))
+ continue;
+ if (be32_to_cpup(addr) == slot)
+ return np;
+ }
+ return NULL;
+}
+
+static struct dw_mci_of_slot_quirks {
+ char *quirk;
+ int id;
+} of_slot_quirks[] = {
+ {
+ .quirk = "disable-wp",
+ .id = DW_MCI_SLOT_QUIRK_NO_WRITE_PROTECT,
+ },
+};
+
+static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
+{
+ struct device_node *np = dw_mci_of_find_slot_node(dev, slot);
+ int quirks = 0;
+ int idx;
+
+ /* get quirks */
+ for (idx = 0; idx < ARRAY_SIZE(of_slot_quirks); idx++)
+ if (of_get_property(np, of_slot_quirks[idx].quirk, NULL)) {
+ dev_warn(dev, "Slot quirk %s is deprecated\n",
+ of_slot_quirks[idx].quirk);
+ quirks |= of_slot_quirks[idx].id;
+ }
+
+ return quirks;
+}
+#else /* CONFIG_OF */
+static int dw_mci_of_get_slot_quirks(struct device *dev, u8 slot)
+{
+ return 0;
+}
+#endif /* CONFIG_OF */
+
+static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
+{
+ struct mmc_host *mmc;
+ struct dw_mci_slot *slot;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int ctrl_id, ret;
+ u32 freq[2];
+
+ mmc = mmc_alloc_host(sizeof(struct dw_mci_slot), host->dev);
+ if (!mmc)
+ return -ENOMEM;
+
+ slot = mmc_priv(mmc);
+ slot->id = id;
+ slot->sdio_id = host->sdio_id0 + id;
+ slot->mmc = mmc;
+ slot->host = host;
+ host->slot[id] = slot;
+
+ slot->quirks = dw_mci_of_get_slot_quirks(host->dev, slot->id);
+
+ mmc->ops = &dw_mci_ops;
+ if (of_property_read_u32_array(host->dev->of_node,
+ "clock-freq-min-max", freq, 2)) {
+ mmc->f_min = DW_MCI_FREQ_MIN;
+ mmc->f_max = DW_MCI_FREQ_MAX;
+ } else {
+ mmc->f_min = freq[0];
+ mmc->f_max = freq[1];
+ }
+
+ /*if there are external regulators, get them*/
+ ret = mmc_regulator_get_supply(mmc);
+ if (ret == -EPROBE_DEFER)
+ goto err_host_allocated;
+
+ if (!mmc->ocr_avail)
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
+
+ if (host->pdata->caps)
+ mmc->caps = host->pdata->caps;
+
+ if (host->pdata->pm_caps)
+ mmc->pm_caps = host->pdata->pm_caps;
+
+ if (host->dev->of_node) {
+ ctrl_id = of_alias_get_id(host->dev->of_node, "mshc");
+ if (ctrl_id < 0)
+ ctrl_id = 0;
+ } else {
+ ctrl_id = to_platform_device(host->dev)->id;
+ }
+ if (drv_data && drv_data->caps)
+ mmc->caps |= drv_data->caps[ctrl_id];
+
+ if (host->pdata->caps2)
+ mmc->caps2 = host->pdata->caps2;
+
+ ret = mmc_of_parse(mmc);
+ if (ret)
+ goto err_host_allocated;
+
+ if (host->pdata->blk_settings) {
+ mmc->max_segs = host->pdata->blk_settings->max_segs;
+ mmc->max_blk_size = host->pdata->blk_settings->max_blk_size;
+ mmc->max_blk_count = host->pdata->blk_settings->max_blk_count;
+ mmc->max_req_size = host->pdata->blk_settings->max_req_size;
+ mmc->max_seg_size = host->pdata->blk_settings->max_seg_size;
+ } else {
+ /* Useful defaults if platform data is unset. */
+#ifdef CONFIG_MMC_DW_IDMAC
+ mmc->max_segs = host->ring_size;
+ mmc->max_blk_size = 65536;
+ mmc->max_seg_size = 0x1000;
+ mmc->max_req_size = mmc->max_seg_size * host->ring_size;
+ mmc->max_blk_count = mmc->max_req_size / 512;
+#else
+ mmc->max_segs = 64;
+ mmc->max_blk_size = 65536; /* BLKSIZ is 16 bits */
+ mmc->max_blk_count = 512;
+ mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
+ mmc->max_seg_size = mmc->max_req_size;
+#endif /* CONFIG_MMC_DW_IDMAC */
+ }
+
+ if (dw_mci_get_cd(mmc))
+ set_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ else
+ clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+
+ ret = mmc_add_host(mmc);
+ if (ret)
+ goto err_host_allocated;
+
+#if defined(CONFIG_DEBUG_FS)
+ dw_mci_init_debugfs(slot);
+#endif
+
+ return 0;
+
+err_host_allocated:
+ mmc_free_host(mmc);
+ return ret;
+}
+
+static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id)
+{
+ /* Debugfs stuff is cleaned up by mmc core */
+ mmc_remove_host(slot->mmc);
+ slot->host->slot[id] = NULL;
+ mmc_free_host(slot->mmc);
+}
+
+static void dw_mci_init_dma(struct dw_mci *host)
+{
+ int addr_config;
+ /* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
+ addr_config = (mci_readl(host, HCON) >> 27) & 0x01;
+
+ if (addr_config == 1) {
+ /* host supports IDMAC in 64-bit address mode */
+ host->dma_64bit_address = 1;
+ dev_info(host->dev, "IDMAC supports 64-bit address mode.\n");
+ if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
+ dma_set_coherent_mask(host->dev, DMA_BIT_MASK(64));
+ } else {
+ /* host supports IDMAC in 32-bit address mode */
+ host->dma_64bit_address = 0;
+ dev_info(host->dev, "IDMAC supports 32-bit address mode.\n");
+ }
+
+ /* Alloc memory for sg translation */
+ host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE,
+ &host->sg_dma, GFP_KERNEL);
+ if (!host->sg_cpu) {
+ dev_err(host->dev, "%s: could not alloc DMA memory\n",
+ __func__);
+ goto no_dma;
+ }
+
+ /* Determine which DMA interface to use */
+#ifdef CONFIG_MMC_DW_IDMAC
+ host->dma_ops = &dw_mci_idmac_ops;
+ dev_info(host->dev, "Using internal DMA controller.\n");
+#endif
+
+ if (!host->dma_ops)
+ goto no_dma;
+
+ if (host->dma_ops->init && host->dma_ops->start &&
+ host->dma_ops->stop && host->dma_ops->cleanup) {
+ if (host->dma_ops->init(host)) {
+ dev_err(host->dev, "%s: Unable to initialize "
+ "DMA Controller.\n", __func__);
+ goto no_dma;
+ }
+ } else {
+ dev_err(host->dev, "DMA initialization not found.\n");
+ goto no_dma;
+ }
+
+ host->use_dma = 1;
+ return;
+
+no_dma:
+ dev_info(host->dev, "Using PIO mode.\n");
+ host->use_dma = 0;
+ return;
+}
+
+static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+ u32 ctrl;
+
+ ctrl = mci_readl(host, CTRL);
+ ctrl |= reset;
+ mci_writel(host, CTRL, ctrl);
+
+ /* wait till resets clear */
+ do {
+ ctrl = mci_readl(host, CTRL);
+ if (!(ctrl & reset))
+ return true;
+ } while (time_before(jiffies, timeout));
+
+ dev_err(host->dev,
+ "Timeout resetting block (ctrl reset %#x)\n",
+ ctrl & reset);
+
+ return false;
+}
+
+static bool dw_mci_reset(struct dw_mci *host)
+{
+ u32 flags = SDMMC_CTRL_RESET | SDMMC_CTRL_FIFO_RESET;
+ bool ret = false;
+
+ /*
+ * Reseting generates a block interrupt, hence setting
+ * the scatter-gather pointer to NULL.
+ */
+ if (host->sg) {
+ sg_miter_stop(&host->sg_miter);
+ host->sg = NULL;
+ }
+
+ if (host->use_dma)
+ flags |= SDMMC_CTRL_DMA_RESET;
+
+ if (dw_mci_ctrl_reset(host, flags)) {
+ /*
+ * In all cases we clear the RAWINTS register to clear any
+ * interrupts.
+ */
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+
+ /* if using dma we wait for dma_req to clear */
+ if (host->use_dma) {
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+ u32 status;
+ do {
+ status = mci_readl(host, STATUS);
+ if (!(status & SDMMC_STATUS_DMA_REQ))
+ break;
+ cpu_relax();
+ } while (time_before(jiffies, timeout));
+
+ if (status & SDMMC_STATUS_DMA_REQ) {
+ dev_err(host->dev,
+ "%s: Timeout waiting for dma_req to "
+ "clear during reset\n", __func__);
+ goto ciu_out;
+ }
+
+ /* when using DMA next we reset the fifo again */
+ if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_FIFO_RESET))
+ goto ciu_out;
+ }
+ } else {
+ /* if the controller reset bit did clear, then set clock regs */
+ if (!(mci_readl(host, CTRL) & SDMMC_CTRL_RESET)) {
+ dev_err(host->dev, "%s: fifo/dma reset bits didn't "
+ "clear but ciu was reset, doing clock update\n",
+ __func__);
+ goto ciu_out;
+ }
+ }
+
+#if IS_ENABLED(CONFIG_MMC_DW_IDMAC)
+ /* It is also recommended that we reset and reprogram idmac */
+ dw_mci_idmac_reset(host);
+#endif
+
+ ret = true;
+
+ciu_out:
+ /* After a CTRL reset we need to have CIU set clock registers */
+ mci_send_cmd(host->cur_slot, SDMMC_CMD_UPD_CLK, 0);
+
+ return ret;
+}
+
+static void dw_mci_cmd11_timer(unsigned long arg)
+{
+ struct dw_mci *host = (struct dw_mci *)arg;
+
+ if (host->state != STATE_SENDING_CMD11) {
+ dev_warn(host->dev, "Unexpected CMD11 timeout\n");
+ return;
+ }
+
+ host->cmd_status = SDMMC_INT_RTO;
+ set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+}
+
+#ifdef CONFIG_OF
+static struct dw_mci_of_quirks {
+ char *quirk;
+ int id;
+} of_quirks[] = {
+ {
+ .quirk = "broken-cd",
+ .id = DW_MCI_QUIRK_BROKEN_CARD_DETECTION,
+ }, {
+ .quirk = "disable-wp",
+ .id = DW_MCI_QUIRK_NO_WRITE_PROTECT,
+ },
+};
+
+static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
+{
+ struct dw_mci_board *pdata;
+ struct device *dev = host->dev;
+ struct device_node *np = dev->of_node;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int idx, ret;
+ u32 clock_frequency;
+
+ pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
+ if (!pdata)
+ return ERR_PTR(-ENOMEM);
+
+ /* find out number of slots supported */
+ if (of_property_read_u32(dev->of_node, "num-slots",
+ &pdata->num_slots)) {
+ dev_info(dev, "num-slots property not found, "
+ "assuming 1 slot is available\n");
+ pdata->num_slots = 1;
+ }
+
+ /* get quirks */
+ for (idx = 0; idx < ARRAY_SIZE(of_quirks); idx++)
+ if (of_get_property(np, of_quirks[idx].quirk, NULL))
+ pdata->quirks |= of_quirks[idx].id;
+
+ if (of_property_read_u32(np, "fifo-depth", &pdata->fifo_depth))
+ dev_info(dev, "fifo-depth property not found, using "
+ "value of FIFOTH register as default\n");
+
+ of_property_read_u32(np, "card-detect-delay", &pdata->detect_delay_ms);
+
+ if (!of_property_read_u32(np, "clock-frequency", &clock_frequency))
+ pdata->bus_hz = clock_frequency;
+
+ if (drv_data && drv_data->parse_dt) {
+ ret = drv_data->parse_dt(host);
+ if (ret)
+ return ERR_PTR(ret);
+ }
+
+ if (of_find_property(np, "supports-highspeed", NULL))
+ pdata->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
+
+ return pdata;
+}
+
+#else /* CONFIG_OF */
+static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host)
+{
+ return ERR_PTR(-EINVAL);
+}
+#endif /* CONFIG_OF */
+
+static void dw_mci_enable_cd(struct dw_mci *host)
+{
+ struct dw_mci_board *brd = host->pdata;
+ unsigned long irqflags;
+ u32 temp;
+ int i;
+
+ /* No need for CD if broken card detection */
+ if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
+ return;
+
+ /* No need for CD if all slots have a non-error GPIO */
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+
+ if (IS_ERR_VALUE(mmc_gpio_get_cd(slot->mmc)))
+ break;
+ }
+ if (i == host->num_slots)
+ return;
+
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ temp = mci_readl(host, INTMASK);
+ temp |= SDMMC_INT_CD;
+ mci_writel(host, INTMASK, temp);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+}
+
+int dw_mci_probe(struct dw_mci *host)
+{
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+ int width, i, ret = 0;
+ u32 fifo_size;
+ int init_slots = 0;
+
+ if (!host->pdata) {
+ host->pdata = dw_mci_parse_dt(host);
+ if (IS_ERR(host->pdata)) {
+ dev_err(host->dev, "platform data not available\n");
+ return -EINVAL;
+ }
+ }
+
+ if (host->pdata->num_slots > 1) {
+ dev_err(host->dev,
+ "Platform data must supply num_slots.\n");
+ return -ENODEV;
+ }
+
+ host->biu_clk = devm_clk_get(host->dev, "biu");
+ if (IS_ERR(host->biu_clk)) {
+ dev_dbg(host->dev, "biu clock not available\n");
+ } else {
+ ret = clk_prepare_enable(host->biu_clk);
+ if (ret) {
+ dev_err(host->dev, "failed to enable biu clock\n");
+ return ret;
+ }
+ }
+
+ host->ciu_clk = devm_clk_get(host->dev, "ciu");
+ if (IS_ERR(host->ciu_clk)) {
+ dev_dbg(host->dev, "ciu clock not available\n");
+ host->bus_hz = host->pdata->bus_hz;
+ } else {
+ ret = clk_prepare_enable(host->ciu_clk);
+ if (ret) {
+ dev_err(host->dev, "failed to enable ciu clock\n");
+ goto err_clk_biu;
+ }
+
+ if (host->pdata->bus_hz) {
+ ret = clk_set_rate(host->ciu_clk, host->pdata->bus_hz);
+ if (ret)
+ dev_warn(host->dev,
+ "Unable to set bus rate to %uHz\n",
+ host->pdata->bus_hz);
+ }
+ host->bus_hz = clk_get_rate(host->ciu_clk);
+ }
+
+ if (!host->bus_hz) {
+ dev_err(host->dev,
+ "Platform data must supply bus speed\n");
+ ret = -ENODEV;
+ goto err_clk_ciu;
+ }
+
+ if (drv_data && drv_data->init) {
+ ret = drv_data->init(host);
+ if (ret) {
+ dev_err(host->dev,
+ "implementation specific init failed\n");
+ goto err_clk_ciu;
+ }
+ }
+
+ if (drv_data && drv_data->setup_clock) {
+ ret = drv_data->setup_clock(host);
+ if (ret) {
+ dev_err(host->dev,
+ "implementation specific clock setup failed\n");
+ goto err_clk_ciu;
+ }
+ }
+
+ setup_timer(&host->cmd11_timer,
+ dw_mci_cmd11_timer, (unsigned long)host);
+
+ host->quirks = host->pdata->quirks;
+
+ spin_lock_init(&host->lock);
+ spin_lock_init(&host->irq_lock);
+ INIT_LIST_HEAD(&host->queue);
+
+ /*
+ * Get the host data width - this assumes that HCON has been set with
+ * the correct values.
+ */
+ i = (mci_readl(host, HCON) >> 7) & 0x7;
+ if (!i) {
+ host->push_data = dw_mci_push_data16;
+ host->pull_data = dw_mci_pull_data16;
+ width = 16;
+ host->data_shift = 1;
+ } else if (i == 2) {
+ host->push_data = dw_mci_push_data64;
+ host->pull_data = dw_mci_pull_data64;
+ width = 64;
+ host->data_shift = 3;
+ } else {
+ /* Check for a reserved value, and warn if it is */
+ WARN((i != 1),
+ "HCON reports a reserved host data width!\n"
+ "Defaulting to 32-bit access.\n");
+ host->push_data = dw_mci_push_data32;
+ host->pull_data = dw_mci_pull_data32;
+ width = 32;
+ host->data_shift = 2;
+ }
+
+ /* Reset all blocks */
+ if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS))
+ return -ENODEV;
+
+ host->dma_ops = host->pdata->dma_ops;
+ dw_mci_init_dma(host);
+
+ /* Clear the interrupts for the host controller */
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
+
+ /* Put in max timeout */
+ mci_writel(host, TMOUT, 0xFFFFFFFF);
+
+ /*
+ * FIFO threshold settings RxMark = fifo_size / 2 - 1,
+ * Tx Mark = fifo_size / 2 DMA Size = 8
+ */
+ if (!host->pdata->fifo_depth) {
+ /*
+ * Power-on value of RX_WMark is FIFO_DEPTH-1, but this may
+ * have been overwritten by the bootloader, just like we're
+ * about to do, so if you know the value for your hardware, you
+ * should put it in the platform data.
+ */
+ fifo_size = mci_readl(host, FIFOTH);
+ fifo_size = 1 + ((fifo_size >> 16) & 0xfff);
+ } else {
+ fifo_size = host->pdata->fifo_depth;
+ }
+ host->fifo_depth = fifo_size;
+ host->fifoth_val =
+ SDMMC_SET_FIFOTH(0x2, fifo_size / 2 - 1, fifo_size / 2);
+ mci_writel(host, FIFOTH, host->fifoth_val);
+
+ /* disable clock to CIU */
+ mci_writel(host, CLKENA, 0);
+ mci_writel(host, CLKSRC, 0);
+
+ /*
+ * In 2.40a spec, Data offset is changed.
+ * Need to check the version-id and set data-offset for DATA register.
+ */
+ host->verid = SDMMC_GET_VERID(mci_readl(host, VERID));
+ dev_info(host->dev, "Version ID is %04x\n", host->verid);
+
+ if (host->verid < DW_MMC_240A)
+ host->fifo_reg = host->regs + DATA_OFFSET;
+ else
+ host->fifo_reg = host->regs + DATA_240A_OFFSET;
+
+ tasklet_init(&host->tasklet, dw_mci_tasklet_func, (unsigned long)host);
+ ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
+ host->irq_flags, "dw-mci", host);
+ if (ret)
+ goto err_dmaunmap;
+
+ if (host->pdata->num_slots)
+ host->num_slots = host->pdata->num_slots;
+ else
+ host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1;
+
+ /*
+ * Enable interrupts for command done, data over, data empty,
+ * receive ready and error such as transmit, receive timeout, crc error
+ */
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
+ SDMMC_INT_TXDR | SDMMC_INT_RXDR |
+ DW_MCI_ERROR_FLAGS);
+ mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE); /* Enable mci interrupt */
+
+ dev_info(host->dev, "DW MMC controller at irq %d, "
+ "%d bit host data width, "
+ "%u deep fifo\n",
+ host->irq, width, fifo_size);
+
+ /* We need at least one slot to succeed */
+ for (i = 0; i < host->num_slots; i++) {
+ ret = dw_mci_init_slot(host, i);
+ if (ret)
+ dev_dbg(host->dev, "slot %d init failed\n", i);
+ else
+ init_slots++;
+ }
+
+ if (init_slots) {
+ dev_info(host->dev, "%d slots initialized\n", init_slots);
+ } else {
+ dev_dbg(host->dev, "attempted to initialize %d slots, "
+ "but failed on all\n", host->num_slots);
+ goto err_dmaunmap;
+ }
+
+ /* Now that slots are all setup, we can enable card detect */
+ dw_mci_enable_cd(host);
+
+ if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO)
+ dev_info(host->dev, "Internal DMAC interrupt fix enabled.\n");
+
+ return 0;
+
+err_dmaunmap:
+ if (host->use_dma && host->dma_ops->exit)
+ host->dma_ops->exit(host);
+
+err_clk_ciu:
+ if (!IS_ERR(host->ciu_clk))
+ clk_disable_unprepare(host->ciu_clk);
+
+err_clk_biu:
+ if (!IS_ERR(host->biu_clk))
+ clk_disable_unprepare(host->biu_clk);
+
+ return ret;
+}
+EXPORT_SYMBOL(dw_mci_probe);
+
+void dw_mci_remove(struct dw_mci *host)
+{
+ int i;
+
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, 0); /* disable all mmc interrupt first */
+
+ for (i = 0; i < host->num_slots; i++) {
+ dev_dbg(host->dev, "remove slot %d\n", i);
+ if (host->slot[i])
+ dw_mci_cleanup_slot(host->slot[i], i);
+ }
+
+ /* disable clock to CIU */
+ mci_writel(host, CLKENA, 0);
+ mci_writel(host, CLKSRC, 0);
+
+ if (host->use_dma && host->dma_ops->exit)
+ host->dma_ops->exit(host);
+
+ if (!IS_ERR(host->ciu_clk))
+ clk_disable_unprepare(host->ciu_clk);
+
+ if (!IS_ERR(host->biu_clk))
+ clk_disable_unprepare(host->biu_clk);
+}
+EXPORT_SYMBOL(dw_mci_remove);
+
+
+
+#ifdef CONFIG_PM_SLEEP
+/*
+ * TODO: we should probably disable the clock to the card in the suspend path.
+ */
+int dw_mci_suspend(struct dw_mci *host)
+{
+ return 0;
+}
+EXPORT_SYMBOL(dw_mci_suspend);
+
+int dw_mci_resume(struct dw_mci *host)
+{
+ int i, ret;
+
+ if (!dw_mci_ctrl_reset(host, SDMMC_CTRL_ALL_RESET_FLAGS)) {
+ ret = -ENODEV;
+ return ret;
+ }
+
+ if (host->use_dma && host->dma_ops->init)
+ host->dma_ops->init(host);
+
+ /*
+ * Restore the initial value at FIFOTH register
+ * And Invalidate the prev_blksz with zero
+ */
+ mci_writel(host, FIFOTH, host->fifoth_val);
+ host->prev_blksz = 0;
+
+ /* Put in max timeout */
+ mci_writel(host, TMOUT, 0xFFFFFFFF);
+
+ mci_writel(host, RINTSTS, 0xFFFFFFFF);
+ mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
+ SDMMC_INT_TXDR | SDMMC_INT_RXDR |
+ DW_MCI_ERROR_FLAGS);
+ mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
+
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+ if (!slot)
+ continue;
+ if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER) {
+ dw_mci_set_ios(slot->mmc, &slot->mmc->ios);
+ dw_mci_setup_bus(slot, true);
+ }
+ }
+
+ /* Now that slots are all setup, we can enable card detect */
+ dw_mci_enable_cd(host);
+
+ return 0;
+}
+EXPORT_SYMBOL(dw_mci_resume);
+#endif /* CONFIG_PM_SLEEP */
+
+static int __init dw_mci_init(void)
+{
+ pr_info("Synopsys Designware Multimedia Card Interface Driver\n");
+ return 0;
+}
+
+static void __exit dw_mci_exit(void)
+{
+}
+
+module_init(dw_mci_init);
+module_exit(dw_mci_exit);
+
+MODULE_DESCRIPTION("DW Multimedia Card Interface driver");
+MODULE_AUTHOR("NXP Semiconductor VietNam");
+MODULE_AUTHOR("Imagination Technologies Ltd");
+MODULE_LICENSE("GPL v2");
Code Review / kvmfornfv.git / blobdiff