--- /dev/null
+/*
+ * Cypress APA trackpad with I2C interface
+ *
+ * Author: Dudley Du <dudl@cypress.com>
+ * Further cleanup and restructuring by:
+ * Daniel Kurtz <djkurtz@chromium.org>
+ * Benson Leung <bleung@chromium.org>
+ *
+ * Copyright (C) 2011-2014 Cypress Semiconductor, Inc.
+ * Copyright (C) 2011-2012 Google, Inc.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <asm/unaligned.h>
+#include "cyapa.h"
+
+
+#define GEN3_MAX_FINGERS 5
+#define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07)
+
+#define BLK_HEAD_BYTES 32
+
+/* Macro for register map group offset. */
+#define PRODUCT_ID_SIZE 16
+#define QUERY_DATA_SIZE 27
+#define REG_PROTOCOL_GEN_QUERY_OFFSET 20
+
+#define REG_OFFSET_DATA_BASE 0x0000
+#define REG_OFFSET_COMMAND_BASE 0x0028
+#define REG_OFFSET_QUERY_BASE 0x002a
+
+#define CYAPA_OFFSET_SOFT_RESET REG_OFFSET_COMMAND_BASE
+#define OP_RECALIBRATION_MASK 0x80
+#define OP_REPORT_BASELINE_MASK 0x40
+#define REG_OFFSET_MAX_BASELINE 0x0026
+#define REG_OFFSET_MIN_BASELINE 0x0027
+
+#define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1)
+#define SET_POWER_MODE_DELAY 10000 /* Unit: us */
+#define SET_POWER_MODE_TRIES 5
+
+#define GEN3_BL_CMD_CHECKSUM_SEED 0xff
+#define GEN3_BL_CMD_INITIATE_BL 0x38
+#define GEN3_BL_CMD_WRITE_BLOCK 0x39
+#define GEN3_BL_CMD_VERIFY_BLOCK 0x3a
+#define GEN3_BL_CMD_TERMINATE_BL 0x3b
+#define GEN3_BL_CMD_LAUNCH_APP 0xa5
+
+/*
+ * CYAPA trackpad device states.
+ * Used in register 0x00, bit1-0, DeviceStatus field.
+ * Other values indicate device is in an abnormal state and must be reset.
+ */
+#define CYAPA_DEV_NORMAL 0x03
+#define CYAPA_DEV_BUSY 0x01
+
+#define CYAPA_FW_BLOCK_SIZE 64
+#define CYAPA_FW_READ_SIZE 16
+#define CYAPA_FW_HDR_START 0x0780
+#define CYAPA_FW_HDR_BLOCK_COUNT 2
+#define CYAPA_FW_HDR_BLOCK_START (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_HDR_SIZE (CYAPA_FW_HDR_BLOCK_COUNT * \
+ CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_DATA_START 0x0800
+#define CYAPA_FW_DATA_BLOCK_COUNT 480
+#define CYAPA_FW_DATA_BLOCK_START (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_DATA_SIZE (CYAPA_FW_DATA_BLOCK_COUNT * \
+ CYAPA_FW_BLOCK_SIZE)
+#define CYAPA_FW_SIZE (CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE)
+#define CYAPA_CMD_LEN 16
+
+#define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b
+#define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1)
+
+
+struct cyapa_touch {
+ /*
+ * high bits or x/y position value
+ * bit 7 - 4: high 4 bits of x position value
+ * bit 3 - 0: high 4 bits of y position value
+ */
+ u8 xy_hi;
+ u8 x_lo; /* low 8 bits of x position value. */
+ u8 y_lo; /* low 8 bits of y position value. */
+ u8 pressure;
+ /* id range is 1 - 15. It is incremented with every new touch. */
+ u8 id;
+} __packed;
+
+struct cyapa_reg_data {
+ /*
+ * bit 0 - 1: device status
+ * bit 3 - 2: power mode
+ * bit 6 - 4: reserved
+ * bit 7: interrupt valid bit
+ */
+ u8 device_status;
+ /*
+ * bit 7 - 4: number of fingers currently touching pad
+ * bit 3: valid data check bit
+ * bit 2: middle mechanism button state if exists
+ * bit 1: right mechanism button state if exists
+ * bit 0: left mechanism button state if exists
+ */
+ u8 finger_btn;
+ /* CYAPA reports up to 5 touches per packet. */
+ struct cyapa_touch touches[5];
+} __packed;
+
+struct gen3_write_block_cmd {
+ u8 checksum_seed; /* Always be 0xff */
+ u8 cmd_code; /* command code: 0x39 */
+ u8 key[8]; /* 8-byte security key */
+ __be16 block_num;
+ u8 block_data[CYAPA_FW_BLOCK_SIZE];
+ u8 block_checksum; /* Calculated using bytes 12 - 75 */
+ u8 cmd_checksum; /* Calculated using bytes 0-76 */
+} __packed;
+
+static const u8 security_key[] = {
+ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 };
+static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03,
+ 0x04, 0x05, 0x06, 0x07 };
+static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03,
+ 0x04, 0x05, 0x06, 0x07 };
+static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04,
+ 0x05, 0x06, 0x07 };
+
+
+ /* for byte read/write command */
+#define CMD_RESET 0
+#define CMD_POWER_MODE 1
+#define CMD_DEV_STATUS 2
+#define CMD_REPORT_MAX_BASELINE 3
+#define CMD_REPORT_MIN_BASELINE 4
+#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
+#define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET)
+#define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE)
+#define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS)
+#define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
+#define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
+
+ /* for group registers read/write command */
+#define REG_GROUP_DATA 0
+#define REG_GROUP_CMD 2
+#define REG_GROUP_QUERY 3
+#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
+#define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA)
+#define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD)
+#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
+
+ /* for register block read/write command */
+#define CMD_BL_STATUS 0
+#define CMD_BL_HEAD 1
+#define CMD_BL_CMD 2
+#define CMD_BL_DATA 3
+#define CMD_BL_ALL 4
+#define CMD_BLK_PRODUCT_ID 5
+#define CMD_BLK_HEAD 6
+#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
+
+/* register block read/write command in bootloader mode */
+#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
+#define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD)
+#define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD)
+#define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA)
+#define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL)
+
+/* register block read/write command in operational mode */
+#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
+#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
+
+ /* for byte read/write command */
+#define CMD_RESET 0
+#define CMD_POWER_MODE 1
+#define CMD_DEV_STATUS 2
+#define CMD_REPORT_MAX_BASELINE 3
+#define CMD_REPORT_MIN_BASELINE 4
+#define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1)
+#define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET)
+#define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE)
+#define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS)
+#define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE)
+#define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE)
+
+ /* for group registers read/write command */
+#define REG_GROUP_DATA 0
+#define REG_GROUP_CMD 2
+#define REG_GROUP_QUERY 3
+#define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3))
+#define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA)
+#define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD)
+#define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY)
+
+ /* for register block read/write command */
+#define CMD_BL_STATUS 0
+#define CMD_BL_HEAD 1
+#define CMD_BL_CMD 2
+#define CMD_BL_DATA 3
+#define CMD_BL_ALL 4
+#define CMD_BLK_PRODUCT_ID 5
+#define CMD_BLK_HEAD 6
+#define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1))
+
+/* register block read/write command in bootloader mode */
+#define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS)
+#define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD)
+#define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD)
+#define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA)
+#define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL)
+
+/* register block read/write command in operational mode */
+#define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID)
+#define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD)
+
+struct cyapa_cmd_len {
+ u8 cmd;
+ u8 len;
+};
+
+/* maps generic CYAPA_CMD_* code to the I2C equivalent */
+static const struct cyapa_cmd_len cyapa_i2c_cmds[] = {
+ { CYAPA_OFFSET_SOFT_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */
+ { REG_OFFSET_COMMAND_BASE + 1, 1 }, /* CYAPA_CMD_POWER_MODE */
+ { REG_OFFSET_DATA_BASE, 1 }, /* CYAPA_CMD_DEV_STATUS */
+ { REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) },
+ /* CYAPA_CMD_GROUP_DATA */
+ { REG_OFFSET_COMMAND_BASE, 0 }, /* CYAPA_CMD_GROUP_CMD */
+ { REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */
+ { BL_HEAD_OFFSET, 3 }, /* CYAPA_CMD_BL_STATUS */
+ { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_HEAD */
+ { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_CMD */
+ { BL_DATA_OFFSET, 16 }, /* CYAPA_CMD_BL_DATA */
+ { BL_HEAD_OFFSET, 32 }, /* CYAPA_CMD_BL_ALL */
+ { REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE },
+ /* CYAPA_CMD_BLK_PRODUCT_ID */
+ { REG_OFFSET_DATA_BASE, 32 }, /* CYAPA_CMD_BLK_HEAD */
+ { REG_OFFSET_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */
+ { REG_OFFSET_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */
+};
+
+static const struct cyapa_cmd_len cyapa_smbus_cmds[] = {
+ { CYAPA_SMBUS_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */
+ { CYAPA_SMBUS_POWER_MODE, 1 }, /* CYAPA_CMD_POWER_MODE */
+ { CYAPA_SMBUS_DEV_STATUS, 1 }, /* CYAPA_CMD_DEV_STATUS */
+ { CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) },
+ /* CYAPA_CMD_GROUP_DATA */
+ { CYAPA_SMBUS_GROUP_CMD, 2 }, /* CYAPA_CMD_GROUP_CMD */
+ { CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE },
+ /* CYAPA_CMD_GROUP_QUERY */
+ { CYAPA_SMBUS_BL_STATUS, 3 }, /* CYAPA_CMD_BL_STATUS */
+ { CYAPA_SMBUS_BL_HEAD, 16 }, /* CYAPA_CMD_BL_HEAD */
+ { CYAPA_SMBUS_BL_CMD, 16 }, /* CYAPA_CMD_BL_CMD */
+ { CYAPA_SMBUS_BL_DATA, 16 }, /* CYAPA_CMD_BL_DATA */
+ { CYAPA_SMBUS_BL_ALL, 32 }, /* CYAPA_CMD_BL_ALL */
+ { CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE },
+ /* CYAPA_CMD_BLK_PRODUCT_ID */
+ { CYAPA_SMBUS_BLK_HEAD, 16 }, /* CYAPA_CMD_BLK_HEAD */
+ { CYAPA_SMBUS_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */
+ { CYAPA_SMBUS_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */
+};
+
+
+/*
+ * cyapa_smbus_read_block - perform smbus block read command
+ * @cyapa - private data structure of the driver
+ * @cmd - the properly encoded smbus command
+ * @len - expected length of smbus command result
+ * @values - buffer to store smbus command result
+ *
+ * Returns negative errno, else the number of bytes written.
+ *
+ * Note:
+ * In trackpad device, the memory block allocated for I2C register map
+ * is 256 bytes, so the max read block for I2C bus is 256 bytes.
+ */
+ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len,
+ u8 *values)
+{
+ ssize_t ret;
+ u8 index;
+ u8 smbus_cmd;
+ u8 *buf;
+ struct i2c_client *client = cyapa->client;
+
+ if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd))
+ return -EINVAL;
+
+ if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) {
+ /* read specific block registers command. */
+ smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
+ ret = i2c_smbus_read_block_data(client, smbus_cmd, values);
+ goto out;
+ }
+
+ ret = 0;
+ for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) {
+ smbus_cmd = SMBUS_ENCODE_IDX(cmd, index);
+ smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ);
+ buf = values + I2C_SMBUS_BLOCK_MAX * index;
+ ret = i2c_smbus_read_block_data(client, smbus_cmd, buf);
+ if (ret < 0)
+ goto out;
+ }
+
+out:
+ return ret > 0 ? len : ret;
+}
+
+static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx)
+{
+ u8 cmd;
+
+ if (cyapa->smbus) {
+ cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+ cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ);
+ } else {
+ cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+ }
+ return i2c_smbus_read_byte_data(cyapa->client, cmd);
+}
+
+static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value)
+{
+ u8 cmd;
+
+ if (cyapa->smbus) {
+ cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+ cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE);
+ } else {
+ cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+ }
+ return i2c_smbus_write_byte_data(cyapa->client, cmd, value);
+}
+
+ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len,
+ u8 *values)
+{
+ return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values);
+}
+
+static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg,
+ size_t len, const u8 *values)
+{
+ return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values);
+}
+
+ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values)
+{
+ u8 cmd;
+ size_t len;
+
+ if (cyapa->smbus) {
+ cmd = cyapa_smbus_cmds[cmd_idx].cmd;
+ len = cyapa_smbus_cmds[cmd_idx].len;
+ return cyapa_smbus_read_block(cyapa, cmd, len, values);
+ }
+ cmd = cyapa_i2c_cmds[cmd_idx].cmd;
+ len = cyapa_i2c_cmds[cmd_idx].len;
+ return cyapa_i2c_reg_read_block(cyapa, cmd, len, values);
+}
+
+/*
+ * Determine the Gen3 trackpad device's current operating state.
+ *
+ */
+static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len)
+{
+ cyapa->state = CYAPA_STATE_NO_DEVICE;
+
+ /* Parse based on Gen3 characteristic registers and bits */
+ if (reg_data[REG_BL_FILE] == BL_FILE &&
+ reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE &&
+ (reg_data[REG_BL_STATUS] ==
+ (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) ||
+ reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) {
+ /*
+ * Normal state after power on or reset,
+ * REG_BL_STATUS == 0x11, firmware image checksum is valid.
+ * REG_BL_STATUS == 0x10, firmware image checksum is invalid.
+ */
+ cyapa->gen = CYAPA_GEN3;
+ cyapa->state = CYAPA_STATE_BL_IDLE;
+ } else if (reg_data[REG_BL_FILE] == BL_FILE &&
+ (reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) ==
+ BL_STATUS_RUNNING) {
+ cyapa->gen = CYAPA_GEN3;
+ if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) {
+ cyapa->state = CYAPA_STATE_BL_BUSY;
+ } else {
+ if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) ==
+ BL_ERROR_BOOTLOADING)
+ cyapa->state = CYAPA_STATE_BL_ACTIVE;
+ else
+ cyapa->state = CYAPA_STATE_BL_IDLE;
+ }
+ } else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) &&
+ (reg_data[REG_OP_DATA1] & OP_DATA_VALID)) {
+ /*
+ * Normal state when running in operational mode,
+ * may also not in full power state or
+ * busying in command process.
+ */
+ if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <=
+ GEN3_MAX_FINGERS) {
+ /* Finger number data is valid. */
+ cyapa->gen = CYAPA_GEN3;
+ cyapa->state = CYAPA_STATE_OP;
+ }
+ } else if (reg_data[REG_OP_STATUS] == 0x0C &&
+ reg_data[REG_OP_DATA1] == 0x08) {
+ /* Op state when first two registers overwritten with 0x00 */
+ cyapa->gen = CYAPA_GEN3;
+ cyapa->state = CYAPA_STATE_OP;
+ } else if (reg_data[REG_BL_STATUS] &
+ (BL_STATUS_RUNNING | BL_STATUS_BUSY)) {
+ cyapa->gen = CYAPA_GEN3;
+ cyapa->state = CYAPA_STATE_BL_BUSY;
+ }
+
+ if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP ||
+ cyapa->state == CYAPA_STATE_BL_IDLE ||
+ cyapa->state == CYAPA_STATE_BL_ACTIVE ||
+ cyapa->state == CYAPA_STATE_BL_BUSY))
+ return 0;
+
+ return -EAGAIN;
+}
+
+/*
+ * Enter bootloader by soft resetting the device.
+ *
+ * If device is already in the bootloader, the function just returns.
+ * Otherwise, reset the device; after reset, device enters bootloader idle
+ * state immediately.
+ *
+ * Returns:
+ * 0 on success
+ * -EAGAIN device was reset, but is not now in bootloader idle state
+ * < 0 if the device never responds within the timeout
+ */
+static int cyapa_gen3_bl_enter(struct cyapa *cyapa)
+{
+ int error;
+ int waiting_time;
+
+ error = cyapa_poll_state(cyapa, 500);
+ if (error)
+ return error;
+ if (cyapa->state == CYAPA_STATE_BL_IDLE) {
+ /* Already in BL_IDLE. Skipping reset. */
+ return 0;
+ }
+
+ if (cyapa->state != CYAPA_STATE_OP)
+ return -EAGAIN;
+
+ cyapa->operational = false;
+ cyapa->state = CYAPA_STATE_NO_DEVICE;
+ error = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, 0x01);
+ if (error)
+ return -EIO;
+
+ usleep_range(25000, 50000);
+ waiting_time = 2000; /* For some shipset, max waiting time is 1~2s. */
+ do {
+ error = cyapa_poll_state(cyapa, 500);
+ if (error) {
+ if (error == -ETIMEDOUT) {
+ waiting_time -= 500;
+ continue;
+ }
+ return error;
+ }
+
+ if ((cyapa->state == CYAPA_STATE_BL_IDLE) &&
+ !(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
+ break;
+
+ msleep(100);
+ waiting_time -= 100;
+ } while (waiting_time > 0);
+
+ if ((cyapa->state != CYAPA_STATE_BL_IDLE) ||
+ (cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG))
+ return -EAGAIN;
+
+ return 0;
+}
+
+static int cyapa_gen3_bl_activate(struct cyapa *cyapa)
+{
+ int error;
+
+ error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_activate),
+ bl_activate);
+ if (error)
+ return error;
+
+ /* Wait for bootloader to activate; takes between 2 and 12 seconds */
+ msleep(2000);
+ error = cyapa_poll_state(cyapa, 11000);
+ if (error)
+ return error;
+ if (cyapa->state != CYAPA_STATE_BL_ACTIVE)
+ return -EAGAIN;
+
+ return 0;
+}
+
+static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa)
+{
+ int error;
+
+ error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate),
+ bl_deactivate);
+ if (error)
+ return error;
+
+ /* Wait for bootloader to switch to idle state; should take < 100ms */
+ msleep(100);
+ error = cyapa_poll_state(cyapa, 500);
+ if (error)
+ return error;
+ if (cyapa->state != CYAPA_STATE_BL_IDLE)
+ return -EAGAIN;
+ return 0;
+}
+
+/*
+ * Exit bootloader
+ *
+ * Send bl_exit command, then wait 50 - 100 ms to let device transition to
+ * operational mode. If this is the first time the device's firmware is
+ * running, it can take up to 2 seconds to calibrate its sensors. So, poll
+ * the device's new state for up to 2 seconds.
+ *
+ * Returns:
+ * -EIO failure while reading from device
+ * -EAGAIN device is stuck in bootloader, b/c it has invalid firmware
+ * 0 device is supported and in operational mode
+ */
+static int cyapa_gen3_bl_exit(struct cyapa *cyapa)
+{
+ int error;
+
+ error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit);
+ if (error)
+ return error;
+
+ /*
+ * Wait for bootloader to exit, and operation mode to start.
+ * Normally, this takes at least 50 ms.
+ */
+ usleep_range(50000, 100000);
+ /*
+ * In addition, when a device boots for the first time after being
+ * updated to new firmware, it must first calibrate its sensors, which
+ * can take up to an additional 2 seconds. If the device power is
+ * running low, this may take even longer.
+ */
+ error = cyapa_poll_state(cyapa, 4000);
+ if (error < 0)
+ return error;
+ if (cyapa->state != CYAPA_STATE_OP)
+ return -EAGAIN;
+
+ return 0;
+}
+
+static u16 cyapa_gen3_csum(const u8 *buf, size_t count)
+{
+ int i;
+ u16 csum = 0;
+
+ for (i = 0; i < count; i++)
+ csum += buf[i];
+
+ return csum;
+}
+
+/*
+ * Verify the integrity of a CYAPA firmware image file.
+ *
+ * The firmware image file is 30848 bytes, composed of 482 64-byte blocks.
+ *
+ * The first 2 blocks are the firmware header.
+ * The next 480 blocks are the firmware image.
+ *
+ * The first two bytes of the header hold the header checksum, computed by
+ * summing the other 126 bytes of the header.
+ * The last two bytes of the header hold the firmware image checksum, computed
+ * by summing the 30720 bytes of the image modulo 0xffff.
+ *
+ * Both checksums are stored little-endian.
+ */
+static int cyapa_gen3_check_fw(struct cyapa *cyapa, const struct firmware *fw)
+{
+ struct device *dev = &cyapa->client->dev;
+ u16 csum;
+ u16 csum_expected;
+
+ /* Firmware must match exact 30848 bytes = 482 64-byte blocks. */
+ if (fw->size != CYAPA_FW_SIZE) {
+ dev_err(dev, "invalid firmware size = %zu, expected %u.\n",
+ fw->size, CYAPA_FW_SIZE);
+ return -EINVAL;
+ }
+
+ /* Verify header block */
+ csum_expected = (fw->data[0] << 8) | fw->data[1];
+ csum = cyapa_gen3_csum(&fw->data[2], CYAPA_FW_HDR_SIZE - 2);
+ if (csum != csum_expected) {
+ dev_err(dev, "%s %04x, expected: %04x\n",
+ "invalid firmware header checksum = ",
+ csum, csum_expected);
+ return -EINVAL;
+ }
+
+ /* Verify firmware image */
+ csum_expected = (fw->data[CYAPA_FW_HDR_SIZE - 2] << 8) |
+ fw->data[CYAPA_FW_HDR_SIZE - 1];
+ csum = cyapa_gen3_csum(&fw->data[CYAPA_FW_HDR_SIZE],
+ CYAPA_FW_DATA_SIZE);
+ if (csum != csum_expected) {
+ dev_err(dev, "%s %04x, expected: %04x\n",
+ "invalid firmware header checksum = ",
+ csum, csum_expected);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+/*
+ * Write a |len| byte long buffer |buf| to the device, by chopping it up into a
+ * sequence of smaller |CYAPA_CMD_LEN|-length write commands.
+ *
+ * The data bytes for a write command are prepended with the 1-byte offset
+ * of the data relative to the start of |buf|.
+ */
+static int cyapa_gen3_write_buffer(struct cyapa *cyapa,
+ const u8 *buf, size_t len)
+{
+ int error;
+ size_t i;
+ unsigned char cmd[CYAPA_CMD_LEN + 1];
+ size_t cmd_len;
+
+ for (i = 0; i < len; i += CYAPA_CMD_LEN) {
+ const u8 *payload = &buf[i];
+
+ cmd_len = (len - i >= CYAPA_CMD_LEN) ? CYAPA_CMD_LEN : len - i;
+ cmd[0] = i;
+ memcpy(&cmd[1], payload, cmd_len);
+
+ error = cyapa_i2c_reg_write_block(cyapa, 0, cmd_len + 1, cmd);
+ if (error)
+ return error;
+ }
+ return 0;
+}
+
+/*
+ * A firmware block write command writes 64 bytes of data to a single flash
+ * page in the device. The 78-byte block write command has the format:
+ * <0xff> <CMD> <Key> <Start> <Data> <Data-Checksum> <CMD Checksum>
+ *
+ * <0xff> - every command starts with 0xff
+ * <CMD> - the write command value is 0x39
+ * <Key> - write commands include an 8-byte key: { 00 01 02 03 04 05 06 07 }
+ * <Block> - Memory Block number (address / 64) (16-bit, big-endian)
+ * <Data> - 64 bytes of firmware image data
+ * <Data Checksum> - sum of 64 <Data> bytes, modulo 0xff
+ * <CMD Checksum> - sum of 77 bytes, from 0xff to <Data Checksum>
+ *
+ * Each write command is split into 5 i2c write transactions of up to 16 bytes.
+ * Each transaction starts with an i2c register offset: (00, 10, 20, 30, 40).
+ */
+static int cyapa_gen3_write_fw_block(struct cyapa *cyapa,
+ u16 block, const u8 *data)
+{
+ int ret;
+ struct gen3_write_block_cmd write_block_cmd;
+ u8 status[BL_STATUS_SIZE];
+ int tries;
+ u8 bl_status, bl_error;
+
+ /* Set write command and security key bytes. */
+ write_block_cmd.checksum_seed = GEN3_BL_CMD_CHECKSUM_SEED;
+ write_block_cmd.cmd_code = GEN3_BL_CMD_WRITE_BLOCK;
+ memcpy(write_block_cmd.key, security_key, sizeof(security_key));
+ put_unaligned_be16(block, &write_block_cmd.block_num);
+ memcpy(write_block_cmd.block_data, data, CYAPA_FW_BLOCK_SIZE);
+ write_block_cmd.block_checksum = cyapa_gen3_csum(
+ write_block_cmd.block_data, CYAPA_FW_BLOCK_SIZE);
+ write_block_cmd.cmd_checksum = cyapa_gen3_csum((u8 *)&write_block_cmd,
+ sizeof(write_block_cmd) - 1);
+
+ ret = cyapa_gen3_write_buffer(cyapa, (u8 *)&write_block_cmd,
+ sizeof(write_block_cmd));
+ if (ret)
+ return ret;
+
+ /* Wait for write to finish */
+ tries = 11; /* Programming for one block can take about 100ms. */
+ do {
+ usleep_range(10000, 20000);
+
+ /* Check block write command result status. */
+ ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET,
+ BL_STATUS_SIZE, status);
+ if (ret != BL_STATUS_SIZE)
+ return (ret < 0) ? ret : -EIO;
+ } while ((status[REG_BL_STATUS] & BL_STATUS_BUSY) && --tries);
+
+ /* Ignore WATCHDOG bit and reserved bits. */
+ bl_status = status[REG_BL_STATUS] & ~BL_STATUS_REV_MASK;
+ bl_error = status[REG_BL_ERROR] & ~BL_ERROR_RESERVED;
+
+ if (bl_status & BL_STATUS_BUSY)
+ ret = -ETIMEDOUT;
+ else if (bl_status != BL_STATUS_RUNNING ||
+ bl_error != BL_ERROR_BOOTLOADING)
+ ret = -EIO;
+ else
+ ret = 0;
+
+ return ret;
+}
+
+static int cyapa_gen3_write_blocks(struct cyapa *cyapa,
+ size_t start_block, size_t block_count,
+ const u8 *image_data)
+{
+ int error;
+ int i;
+
+ for (i = 0; i < block_count; i++) {
+ size_t block = start_block + i;
+ size_t addr = i * CYAPA_FW_BLOCK_SIZE;
+ const u8 *data = &image_data[addr];
+
+ error = cyapa_gen3_write_fw_block(cyapa, block, data);
+ if (error)
+ return error;
+ }
+ return 0;
+}
+
+static int cyapa_gen3_do_fw_update(struct cyapa *cyapa,
+ const struct firmware *fw)
+{
+ struct device *dev = &cyapa->client->dev;
+ int error;
+
+ /* First write data, starting at byte 128 of fw->data */
+ error = cyapa_gen3_write_blocks(cyapa,
+ CYAPA_FW_DATA_BLOCK_START, CYAPA_FW_DATA_BLOCK_COUNT,
+ &fw->data[CYAPA_FW_HDR_BLOCK_COUNT * CYAPA_FW_BLOCK_SIZE]);
+ if (error) {
+ dev_err(dev, "FW update aborted, write image: %d\n", error);
+ return error;
+ }
+
+ /* Then write checksum */
+ error = cyapa_gen3_write_blocks(cyapa,
+ CYAPA_FW_HDR_BLOCK_START, CYAPA_FW_HDR_BLOCK_COUNT,
+ &fw->data[0]);
+ if (error) {
+ dev_err(dev, "FW update aborted, write checksum: %d\n", error);
+ return error;
+ }
+
+ return 0;
+}
+
+static ssize_t cyapa_gen3_do_calibrate(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct cyapa *cyapa = dev_get_drvdata(dev);
+ int tries;
+ int ret;
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
+ if (ret < 0) {
+ dev_err(dev, "Error reading dev status: %d\n", ret);
+ goto out;
+ }
+ if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) {
+ dev_warn(dev, "Trackpad device is busy, device state: 0x%02x\n",
+ ret);
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET,
+ OP_RECALIBRATION_MASK);
+ if (ret < 0) {
+ dev_err(dev, "Failed to send calibrate command: %d\n",
+ ret);
+ goto out;
+ }
+
+ tries = 20; /* max recalibration timeout 2s. */
+ do {
+ /*
+ * For this recalibration, the max time will not exceed 2s.
+ * The average time is approximately 500 - 700 ms, and we
+ * will check the status every 100 - 200ms.
+ */
+ usleep_range(100000, 200000);
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
+ if (ret < 0) {
+ dev_err(dev, "Error reading dev status: %d\n",
+ ret);
+ goto out;
+ }
+ if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL)
+ break;
+ } while (--tries);
+
+ if (tries == 0) {
+ dev_err(dev, "Failed to calibrate. Timeout.\n");
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+ dev_dbg(dev, "Calibration successful.\n");
+
+out:
+ return ret < 0 ? ret : count;
+}
+
+static ssize_t cyapa_gen3_show_baseline(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct cyapa *cyapa = dev_get_drvdata(dev);
+ int max_baseline, min_baseline;
+ int tries;
+ int ret;
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
+ if (ret < 0) {
+ dev_err(dev, "Error reading dev status. err = %d\n", ret);
+ goto out;
+ }
+ if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) {
+ dev_warn(dev, "Trackpad device is busy. device state = 0x%x\n",
+ ret);
+ ret = -EAGAIN;
+ goto out;
+ }
+
+ ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET,
+ OP_REPORT_BASELINE_MASK);
+ if (ret < 0) {
+ dev_err(dev, "Failed to send report baseline command. %d\n",
+ ret);
+ goto out;
+ }
+
+ tries = 3; /* Try for 30 to 60 ms */
+ do {
+ usleep_range(10000, 20000);
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS);
+ if (ret < 0) {
+ dev_err(dev, "Error reading dev status. err = %d\n",
+ ret);
+ goto out;
+ }
+ if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL)
+ break;
+ } while (--tries);
+
+ if (tries == 0) {
+ dev_err(dev, "Device timed out going to Normal state.\n");
+ ret = -ETIMEDOUT;
+ goto out;
+ }
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_MAX_BASELINE);
+ if (ret < 0) {
+ dev_err(dev, "Failed to read max baseline. err = %d\n", ret);
+ goto out;
+ }
+ max_baseline = ret;
+
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_MIN_BASELINE);
+ if (ret < 0) {
+ dev_err(dev, "Failed to read min baseline. err = %d\n", ret);
+ goto out;
+ }
+ min_baseline = ret;
+
+ dev_dbg(dev, "Baseline report successful. Max: %d Min: %d\n",
+ max_baseline, min_baseline);
+ ret = scnprintf(buf, PAGE_SIZE, "%d %d\n", max_baseline, min_baseline);
+
+out:
+ return ret;
+}
+
+/*
+ * cyapa_get_wait_time_for_pwr_cmd
+ *
+ * Compute the amount of time we need to wait after updating the touchpad
+ * power mode. The touchpad needs to consume the incoming power mode set
+ * command at the current clock rate.
+ */
+
+static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode)
+{
+ switch (pwr_mode) {
+ case PWR_MODE_FULL_ACTIVE: return 20;
+ case PWR_MODE_BTN_ONLY: return 20;
+ case PWR_MODE_OFF: return 20;
+ default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50;
+ }
+}
+
+/*
+ * Set device power mode
+ *
+ * Write to the field to configure power state. Power states include :
+ * Full : Max scans and report rate.
+ * Idle : Report rate set by user specified time.
+ * ButtonOnly : No scans for fingers. When the button is triggered,
+ * a slave interrupt is asserted to notify host to wake up.
+ * Off : Only awake for i2c commands from host. No function for button
+ * or touch sensors.
+ *
+ * The power_mode command should conform to the following :
+ * Full : 0x3f
+ * Idle : Configurable from 20 to 1000ms. See note below for
+ * cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time
+ * ButtonOnly : 0x01
+ * Off : 0x00
+ *
+ * Device power mode can only be set when device is in operational mode.
+ */
+static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode,
+ u16 always_unused)
+{
+ int ret;
+ u8 power;
+ int tries;
+ u16 sleep_time;
+
+ always_unused = 0;
+ if (cyapa->state != CYAPA_STATE_OP)
+ return 0;
+
+ tries = SET_POWER_MODE_TRIES;
+ while (tries--) {
+ ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE);
+ if (ret >= 0)
+ break;
+ usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
+ }
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Return early if the power mode to set is the same as the current
+ * one.
+ */
+ if ((ret & PWR_MODE_MASK) == power_mode)
+ return 0;
+
+ sleep_time = cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK);
+ power = ret;
+ power &= ~PWR_MODE_MASK;
+ power |= power_mode & PWR_MODE_MASK;
+ tries = SET_POWER_MODE_TRIES;
+ while (tries--) {
+ ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power);
+ if (!ret)
+ break;
+ usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY);
+ }
+
+ /*
+ * Wait for the newly set power command to go in at the previous
+ * clock speed (scanrate) used by the touchpad firmware. Not
+ * doing so before issuing the next command may result in errors
+ * depending on the command's content.
+ */
+ msleep(sleep_time);
+ return ret;
+}
+
+static int cyapa_gen3_get_query_data(struct cyapa *cyapa)
+{
+ u8 query_data[QUERY_DATA_SIZE];
+ int ret;
+
+ if (cyapa->state != CYAPA_STATE_OP)
+ return -EBUSY;
+
+ ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data);
+ if (ret != QUERY_DATA_SIZE)
+ return (ret < 0) ? ret : -EIO;
+
+ memcpy(&cyapa->product_id[0], &query_data[0], 5);
+ cyapa->product_id[5] = '-';
+ memcpy(&cyapa->product_id[6], &query_data[5], 6);
+ cyapa->product_id[12] = '-';
+ memcpy(&cyapa->product_id[13], &query_data[11], 2);
+ cyapa->product_id[15] = '\0';
+
+ cyapa->fw_maj_ver = query_data[15];
+ cyapa->fw_min_ver = query_data[16];
+
+ cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK;
+
+ cyapa->gen = query_data[20] & 0x0f;
+
+ cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22];
+ cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23];
+
+ cyapa->physical_size_x =
+ ((query_data[24] & 0xf0) << 4) | query_data[25];
+ cyapa->physical_size_y =
+ ((query_data[24] & 0x0f) << 8) | query_data[26];
+
+ cyapa->max_z = 255;
+
+ return 0;
+}
+
+static int cyapa_gen3_bl_query_data(struct cyapa *cyapa)
+{
+ u8 bl_data[CYAPA_CMD_LEN];
+ int ret;
+
+ ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data);
+ if (ret != CYAPA_CMD_LEN)
+ return (ret < 0) ? ret : -EIO;
+
+ /*
+ * This value will be updated again when entered application mode.
+ * If TP failed to enter application mode, this fw version values
+ * can be used as a reference.
+ * This firmware version valid when fw image checksum is valid.
+ */
+ if (bl_data[REG_BL_STATUS] ==
+ (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) {
+ cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET];
+ cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET];
+ }
+
+ return 0;
+}
+
+/*
+ * Check if device is operational.
+ *
+ * An operational device is responding, has exited bootloader, and has
+ * firmware supported by this driver.
+ *
+ * Returns:
+ * -EBUSY no device or in bootloader
+ * -EIO failure while reading from device
+ * -EAGAIN device is still in bootloader
+ * if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware
+ * -EINVAL device is in operational mode, but not supported by this driver
+ * 0 device is supported
+ */
+static int cyapa_gen3_do_operational_check(struct cyapa *cyapa)
+{
+ struct device *dev = &cyapa->client->dev;
+ int error;
+
+ switch (cyapa->state) {
+ case CYAPA_STATE_BL_ACTIVE:
+ error = cyapa_gen3_bl_deactivate(cyapa);
+ if (error) {
+ dev_err(dev, "failed to bl_deactivate: %d\n", error);
+ return error;
+ }
+
+ /* Fallthrough state */
+ case CYAPA_STATE_BL_IDLE:
+ /* Try to get firmware version in bootloader mode. */
+ cyapa_gen3_bl_query_data(cyapa);
+
+ error = cyapa_gen3_bl_exit(cyapa);
+ if (error) {
+ dev_err(dev, "failed to bl_exit: %d\n", error);
+ return error;
+ }
+
+ /* Fallthrough state */
+ case CYAPA_STATE_OP:
+ /*
+ * Reading query data before going back to the full mode
+ * may cause problems, so we set the power mode first here.
+ */
+ error = cyapa_gen3_set_power_mode(cyapa,
+ PWR_MODE_FULL_ACTIVE, 0);
+ if (error)
+ dev_err(dev, "%s: set full power mode failed: %d\n",
+ __func__, error);
+ error = cyapa_gen3_get_query_data(cyapa);
+ if (error < 0)
+ return error;
+
+ /* Only support firmware protocol gen3 */
+ if (cyapa->gen != CYAPA_GEN3) {
+ dev_err(dev, "unsupported protocol version (%d)",
+ cyapa->gen);
+ return -EINVAL;
+ }
+
+ /* Only support product ID starting with CYTRA */
+ if (memcmp(cyapa->product_id, product_id,
+ strlen(product_id)) != 0) {
+ dev_err(dev, "unsupported product ID (%s)\n",
+ cyapa->product_id);
+ return -EINVAL;
+ }
+
+ return 0;
+
+ default:
+ return -EIO;
+ }
+ return 0;
+}
+
+/*
+ * Return false, do not continue process
+ * Return true, continue process.
+ */
+static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa)
+{
+ /* Not gen3 irq command response, skip for continue. */
+ if (cyapa->gen != CYAPA_GEN3)
+ return true;
+
+ if (cyapa->operational)
+ return true;
+
+ /*
+ * Driver in detecting or other interface function processing,
+ * so, stop cyapa_gen3_irq_handler to continue process to
+ * avoid unwanted to error detecting and processing.
+ *
+ * And also, avoid the periodicly accerted interrupts to be processed
+ * as touch inputs when gen3 failed to launch into application mode,
+ * which will cause gen3 stays in bootloader mode.
+ */
+ return false;
+}
+
+static int cyapa_gen3_irq_handler(struct cyapa *cyapa)
+{
+ struct input_dev *input = cyapa->input;
+ struct device *dev = &cyapa->client->dev;
+ struct cyapa_reg_data data;
+ int num_fingers;
+ int ret;
+ int i;
+
+ ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data);
+ if (ret != sizeof(data)) {
+ dev_err(dev, "failed to read report data, (%d)\n", ret);
+ return -EINVAL;
+ }
+
+ if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC ||
+ (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL ||
+ (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) {
+ dev_err(dev, "invalid device state bytes, %02x %02x\n",
+ data.device_status, data.finger_btn);
+ return -EINVAL;
+ }
+
+ num_fingers = (data.finger_btn >> 4) & 0x0f;
+ for (i = 0; i < num_fingers; i++) {
+ const struct cyapa_touch *touch = &data.touches[i];
+ /* Note: touch->id range is 1 to 15; slots are 0 to 14. */
+ int slot = touch->id - 1;
+
+ input_mt_slot(input, slot);
+ input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
+ input_report_abs(input, ABS_MT_POSITION_X,
+ ((touch->xy_hi & 0xf0) << 4) | touch->x_lo);
+ input_report_abs(input, ABS_MT_POSITION_Y,
+ ((touch->xy_hi & 0x0f) << 8) | touch->y_lo);
+ input_report_abs(input, ABS_MT_PRESSURE, touch->pressure);
+ }
+
+ input_mt_sync_frame(input);
+
+ if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK)
+ input_report_key(input, BTN_LEFT,
+ !!(data.finger_btn & OP_DATA_LEFT_BTN));
+ if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK)
+ input_report_key(input, BTN_MIDDLE,
+ !!(data.finger_btn & OP_DATA_MIDDLE_BTN));
+ if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK)
+ input_report_key(input, BTN_RIGHT,
+ !!(data.finger_btn & OP_DATA_RIGHT_BTN));
+ input_sync(input);
+
+ return 0;
+}
+
+static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; }
+static int cyapa_gen3_bl_initiate(struct cyapa *cyapa,
+ const struct firmware *fw) { return 0; }
+static int cyapa_gen3_empty_output_data(struct cyapa *cyapa,
+ u8 *buf, int *len, cb_sort func) { return 0; }
+
+const struct cyapa_dev_ops cyapa_gen3_ops = {
+ .check_fw = cyapa_gen3_check_fw,
+ .bl_enter = cyapa_gen3_bl_enter,
+ .bl_activate = cyapa_gen3_bl_activate,
+ .update_fw = cyapa_gen3_do_fw_update,
+ .bl_deactivate = cyapa_gen3_bl_deactivate,
+ .bl_initiate = cyapa_gen3_bl_initiate,
+
+ .show_baseline = cyapa_gen3_show_baseline,
+ .calibrate_store = cyapa_gen3_do_calibrate,
+
+ .initialize = cyapa_gen3_initialize,
+
+ .state_parse = cyapa_gen3_state_parse,
+ .operational_check = cyapa_gen3_do_operational_check,
+
+ .irq_handler = cyapa_gen3_irq_handler,
+ .irq_cmd_handler = cyapa_gen3_irq_cmd_handler,
+ .sort_empty_output_data = cyapa_gen3_empty_output_data,
+ .set_power_mode = cyapa_gen3_set_power_mode,
+};
Code Review / kvmfornfv.git / blobdiff