--- /dev/null
+/*
+ * Copyright (c) 2003-2006 Silicon Graphics, Inc. All Rights Reserved.
+ * Copyright (C) 2008-2009 MontaVista Software, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it would be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this program; if not, write the Free Software
+ * Foundation, Inc., 59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
+ *
+ * For further information regarding this notice, see:
+ *
+ * http://oss.sgi.com/projects/GenInfo/NoticeExplan
+ */
+
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/scatterlist.h>
+#include <linux/ioc4.h>
+#include <linux/io.h>
+#include <linux/ide.h>
+
+#define DRV_NAME "SGIIOC4"
+
+/* IOC4 Specific Definitions */
+#define IOC4_CMD_OFFSET 0x100
+#define IOC4_CTRL_OFFSET 0x120
+#define IOC4_DMA_OFFSET 0x140
+#define IOC4_INTR_OFFSET 0x0
+
+#define IOC4_TIMING 0x00
+#define IOC4_DMA_PTR_L 0x01
+#define IOC4_DMA_PTR_H 0x02
+#define IOC4_DMA_ADDR_L 0x03
+#define IOC4_DMA_ADDR_H 0x04
+#define IOC4_BC_DEV 0x05
+#define IOC4_BC_MEM 0x06
+#define IOC4_DMA_CTRL 0x07
+#define IOC4_DMA_END_ADDR 0x08
+
+/* Bits in the IOC4 Control/Status Register */
+#define IOC4_S_DMA_START 0x01
+#define IOC4_S_DMA_STOP 0x02
+#define IOC4_S_DMA_DIR 0x04
+#define IOC4_S_DMA_ACTIVE 0x08
+#define IOC4_S_DMA_ERROR 0x10
+#define IOC4_ATA_MEMERR 0x02
+
+/* Read/Write Directions */
+#define IOC4_DMA_WRITE 0x04
+#define IOC4_DMA_READ 0x00
+
+/* Interrupt Register Offsets */
+#define IOC4_INTR_REG 0x03
+#define IOC4_INTR_SET 0x05
+#define IOC4_INTR_CLEAR 0x07
+
+#define IOC4_IDE_CACHELINE_SIZE 128
+#define IOC4_CMD_CTL_BLK_SIZE 0x20
+#define IOC4_SUPPORTED_FIRMWARE_REV 46
+
+struct ioc4_dma_regs {
+ u32 timing_reg0;
+ u32 timing_reg1;
+ u32 low_mem_ptr;
+ u32 high_mem_ptr;
+ u32 low_mem_addr;
+ u32 high_mem_addr;
+ u32 dev_byte_count;
+ u32 mem_byte_count;
+ u32 status;
+};
+
+/* Each Physical Region Descriptor Entry size is 16 bytes (2 * 64 bits) */
+/* IOC4 has only 1 IDE channel */
+#define IOC4_PRD_BYTES 16
+#define IOC4_PRD_ENTRIES (PAGE_SIZE / (4 * IOC4_PRD_BYTES))
+
+
+static void sgiioc4_init_hwif_ports(struct ide_hw *hw,
+ unsigned long data_port,
+ unsigned long ctrl_port,
+ unsigned long irq_port)
+{
+ unsigned long reg = data_port;
+ int i;
+
+ /* Registers are word (32 bit) aligned */
+ for (i = 0; i <= 7; i++)
+ hw->io_ports_array[i] = reg + i * 4;
+
+ hw->io_ports.ctl_addr = ctrl_port;
+ hw->io_ports.irq_addr = irq_port;
+}
+
+static int sgiioc4_checkirq(ide_hwif_t *hwif)
+{
+ unsigned long intr_addr = hwif->io_ports.irq_addr + IOC4_INTR_REG * 4;
+
+ if (readl((void __iomem *)intr_addr) & 0x03)
+ return 1;
+
+ return 0;
+}
+
+static u8 sgiioc4_read_status(ide_hwif_t *);
+
+static int sgiioc4_clearirq(ide_drive_t *drive)
+{
+ u32 intr_reg;
+ ide_hwif_t *hwif = drive->hwif;
+ struct ide_io_ports *io_ports = &hwif->io_ports;
+ unsigned long other_ir = io_ports->irq_addr + (IOC4_INTR_REG << 2);
+
+ /* Code to check for PCI error conditions */
+ intr_reg = readl((void __iomem *)other_ir);
+ if (intr_reg & 0x03) { /* Valid IOC4-IDE interrupt */
+ /*
+ * Using sgiioc4_read_status to read the Status register has a
+ * side effect of clearing the interrupt. The first read should
+ * clear it if it is set. The second read should return
+ * a "clear" status if it got cleared. If not, then spin
+ * for a bit trying to clear it.
+ */
+ u8 stat = sgiioc4_read_status(hwif);
+ int count = 0;
+
+ stat = sgiioc4_read_status(hwif);
+ while ((stat & ATA_BUSY) && (count++ < 100)) {
+ udelay(1);
+ stat = sgiioc4_read_status(hwif);
+ }
+
+ if (intr_reg & 0x02) {
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ /* Error when transferring DMA data on PCI bus */
+ u32 pci_err_addr_low, pci_err_addr_high,
+ pci_stat_cmd_reg;
+
+ pci_err_addr_low =
+ readl((void __iomem *)io_ports->irq_addr);
+ pci_err_addr_high =
+ readl((void __iomem *)(io_ports->irq_addr + 4));
+ pci_read_config_dword(dev, PCI_COMMAND,
+ &pci_stat_cmd_reg);
+ printk(KERN_ERR "%s(%s): PCI Bus Error when doing DMA: "
+ "status-cmd reg is 0x%x\n",
+ __func__, drive->name, pci_stat_cmd_reg);
+ printk(KERN_ERR "%s(%s): PCI Error Address is 0x%x%x\n",
+ __func__, drive->name,
+ pci_err_addr_high, pci_err_addr_low);
+ /* Clear the PCI Error indicator */
+ pci_write_config_dword(dev, PCI_COMMAND, 0x00000146);
+ }
+
+ /* Clear the Interrupt, Error bits on the IOC4 */
+ writel(0x03, (void __iomem *)other_ir);
+
+ intr_reg = readl((void __iomem *)other_ir);
+ }
+
+ return intr_reg & 3;
+}
+
+static void sgiioc4_dma_start(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned long ioc4_dma_addr = hwif->dma_base + IOC4_DMA_CTRL * 4;
+ unsigned int reg = readl((void __iomem *)ioc4_dma_addr);
+ unsigned int temp_reg = reg | IOC4_S_DMA_START;
+
+ writel(temp_reg, (void __iomem *)ioc4_dma_addr);
+}
+
+static u32 sgiioc4_ide_dma_stop(ide_hwif_t *hwif, u64 dma_base)
+{
+ unsigned long ioc4_dma_addr = dma_base + IOC4_DMA_CTRL * 4;
+ u32 ioc4_dma;
+ int count;
+
+ count = 0;
+ ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
+ while ((ioc4_dma & IOC4_S_DMA_STOP) && (count++ < 200)) {
+ udelay(1);
+ ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
+ }
+ return ioc4_dma;
+}
+
+/* Stops the IOC4 DMA Engine */
+static int sgiioc4_dma_end(ide_drive_t *drive)
+{
+ u32 ioc4_dma, bc_dev, bc_mem, num, valid = 0, cnt = 0;
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned long dma_base = hwif->dma_base;
+ int dma_stat = 0;
+ unsigned long *ending_dma = ide_get_hwifdata(hwif);
+
+ writel(IOC4_S_DMA_STOP, (void __iomem *)(dma_base + IOC4_DMA_CTRL * 4));
+
+ ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);
+
+ if (ioc4_dma & IOC4_S_DMA_STOP) {
+ printk(KERN_ERR
+ "%s(%s): IOC4 DMA STOP bit is still 1 :"
+ "ioc4_dma_reg 0x%x\n",
+ __func__, drive->name, ioc4_dma);
+ dma_stat = 1;
+ }
+
+ /*
+ * The IOC4 will DMA 1's to the ending DMA area to indicate that
+ * previous data DMA is complete. This is necessary because of relaxed
+ * ordering between register reads and DMA writes on the Altix.
+ */
+ while ((cnt++ < 200) && (!valid)) {
+ for (num = 0; num < 16; num++) {
+ if (ending_dma[num]) {
+ valid = 1;
+ break;
+ }
+ }
+ udelay(1);
+ }
+ if (!valid) {
+ printk(KERN_ERR "%s(%s) : DMA incomplete\n", __func__,
+ drive->name);
+ dma_stat = 1;
+ }
+
+ bc_dev = readl((void __iomem *)(dma_base + IOC4_BC_DEV * 4));
+ bc_mem = readl((void __iomem *)(dma_base + IOC4_BC_MEM * 4));
+
+ if ((bc_dev & 0x01FF) || (bc_mem & 0x1FF)) {
+ if (bc_dev > bc_mem + 8) {
+ printk(KERN_ERR
+ "%s(%s): WARNING!! byte_count_dev %d "
+ "!= byte_count_mem %d\n",
+ __func__, drive->name, bc_dev, bc_mem);
+ }
+ }
+
+ return dma_stat;
+}
+
+static void sgiioc4_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive)
+{
+}
+
+/* Returns 1 if DMA IRQ issued, 0 otherwise */
+static int sgiioc4_dma_test_irq(ide_drive_t *drive)
+{
+ return sgiioc4_checkirq(drive->hwif);
+}
+
+static void sgiioc4_dma_host_set(ide_drive_t *drive, int on)
+{
+ if (!on)
+ sgiioc4_clearirq(drive);
+}
+
+static void sgiioc4_resetproc(ide_drive_t *drive)
+{
+ struct ide_cmd *cmd = &drive->hwif->cmd;
+
+ sgiioc4_dma_end(drive);
+ ide_dma_unmap_sg(drive, cmd);
+ sgiioc4_clearirq(drive);
+}
+
+static void sgiioc4_dma_lost_irq(ide_drive_t *drive)
+{
+ sgiioc4_resetproc(drive);
+
+ ide_dma_lost_irq(drive);
+}
+
+static u8 sgiioc4_read_status(ide_hwif_t *hwif)
+{
+ unsigned long port = hwif->io_ports.status_addr;
+ u8 reg = (u8) readb((void __iomem *) port);
+
+ if (!(reg & ATA_BUSY)) { /* Not busy... check for interrupt */
+ unsigned long other_ir = port - 0x110;
+ unsigned int intr_reg = (u32) readl((void __iomem *) other_ir);
+
+ /* Clear the Interrupt, Error bits on the IOC4 */
+ if (intr_reg & 0x03) {
+ writel(0x03, (void __iomem *) other_ir);
+ intr_reg = (u32) readl((void __iomem *) other_ir);
+ }
+ }
+
+ return reg;
+}
+
+/* Creates a DMA map for the scatter-gather list entries */
+static int ide_dma_sgiioc4(ide_hwif_t *hwif, const struct ide_port_info *d)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ unsigned long dma_base = pci_resource_start(dev, 0) + IOC4_DMA_OFFSET;
+ int num_ports = sizeof(struct ioc4_dma_regs);
+ void *pad;
+
+ printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name);
+
+ if (request_mem_region(dma_base, num_ports, hwif->name) == NULL) {
+ printk(KERN_ERR "%s(%s) -- ERROR: addresses 0x%08lx to 0x%08lx "
+ "already in use\n", __func__, hwif->name,
+ dma_base, dma_base + num_ports - 1);
+ return -1;
+ }
+
+ hwif->dma_base = (unsigned long)hwif->io_ports.irq_addr +
+ IOC4_DMA_OFFSET;
+
+ hwif->sg_max_nents = IOC4_PRD_ENTRIES;
+
+ hwif->prd_max_nents = IOC4_PRD_ENTRIES;
+ hwif->prd_ent_size = IOC4_PRD_BYTES;
+
+ if (ide_allocate_dma_engine(hwif))
+ goto dma_pci_alloc_failure;
+
+ pad = dma_alloc_coherent(&dev->dev, IOC4_IDE_CACHELINE_SIZE,
+ (dma_addr_t *)&hwif->extra_base, GFP_KERNEL);
+ if (pad) {
+ ide_set_hwifdata(hwif, pad);
+ return 0;
+ }
+
+ ide_release_dma_engine(hwif);
+
+ printk(KERN_ERR "%s(%s) -- ERROR: Unable to allocate DMA maps\n",
+ __func__, hwif->name);
+ printk(KERN_INFO "%s: changing from DMA to PIO mode", hwif->name);
+
+dma_pci_alloc_failure:
+ release_mem_region(dma_base, num_ports);
+
+ return -1;
+}
+
+/* Initializes the IOC4 DMA Engine */
+static void sgiioc4_configure_for_dma(int dma_direction, ide_drive_t *drive)
+{
+ u32 ioc4_dma;
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned long dma_base = hwif->dma_base;
+ unsigned long ioc4_dma_addr = dma_base + IOC4_DMA_CTRL * 4;
+ u32 dma_addr, ending_dma_addr;
+
+ ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
+
+ if (ioc4_dma & IOC4_S_DMA_ACTIVE) {
+ printk(KERN_WARNING "%s(%s): Warning!! DMA from previous "
+ "transfer was still active\n", __func__, drive->name);
+ writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
+ ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);
+
+ if (ioc4_dma & IOC4_S_DMA_STOP)
+ printk(KERN_ERR "%s(%s): IOC4 DMA STOP bit is "
+ "still 1\n", __func__, drive->name);
+ }
+
+ ioc4_dma = readl((void __iomem *)ioc4_dma_addr);
+ if (ioc4_dma & IOC4_S_DMA_ERROR) {
+ printk(KERN_WARNING "%s(%s): Warning!! DMA Error during "
+ "previous transfer, status 0x%x\n",
+ __func__, drive->name, ioc4_dma);
+ writel(IOC4_S_DMA_STOP, (void __iomem *)ioc4_dma_addr);
+ ioc4_dma = sgiioc4_ide_dma_stop(hwif, dma_base);
+
+ if (ioc4_dma & IOC4_S_DMA_STOP)
+ printk(KERN_ERR "%s(%s): IOC4 DMA STOP bit is "
+ "still 1\n", __func__, drive->name);
+ }
+
+ /* Address of the Scatter Gather List */
+ dma_addr = cpu_to_le32(hwif->dmatable_dma);
+ writel(dma_addr, (void __iomem *)(dma_base + IOC4_DMA_PTR_L * 4));
+
+ /* Address of the Ending DMA */
+ memset(ide_get_hwifdata(hwif), 0, IOC4_IDE_CACHELINE_SIZE);
+ ending_dma_addr = cpu_to_le32(hwif->extra_base);
+ writel(ending_dma_addr, (void __iomem *)(dma_base +
+ IOC4_DMA_END_ADDR * 4));
+
+ writel(dma_direction, (void __iomem *)ioc4_dma_addr);
+}
+
+/* IOC4 Scatter Gather list Format */
+/* 128 Bit entries to support 64 bit addresses in the future */
+/* The Scatter Gather list Entry should be in the BIG-ENDIAN Format */
+/* --------------------------------------------------------------------- */
+/* | Upper 32 bits - Zero | Lower 32 bits- address | */
+/* --------------------------------------------------------------------- */
+/* | Upper 32 bits - Zero |EOL| 15 unused | 16 Bit Length| */
+/* --------------------------------------------------------------------- */
+/* Creates the scatter gather list, DMA Table */
+
+static int sgiioc4_build_dmatable(ide_drive_t *drive, struct ide_cmd *cmd)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ unsigned int *table = hwif->dmatable_cpu;
+ unsigned int count = 0, i = cmd->sg_nents;
+ struct scatterlist *sg = hwif->sg_table;
+
+ while (i && sg_dma_len(sg)) {
+ dma_addr_t cur_addr;
+ int cur_len;
+ cur_addr = sg_dma_address(sg);
+ cur_len = sg_dma_len(sg);
+
+ while (cur_len) {
+ if (count++ >= IOC4_PRD_ENTRIES) {
+ printk(KERN_WARNING
+ "%s: DMA table too small\n",
+ drive->name);
+ return 0;
+ } else {
+ u32 bcount =
+ 0x10000 - (cur_addr & 0xffff);
+
+ if (bcount > cur_len)
+ bcount = cur_len;
+
+ /*
+ * Put the address, length in
+ * the IOC4 dma-table format
+ */
+ *table = 0x0;
+ table++;
+ *table = cpu_to_be32(cur_addr);
+ table++;
+ *table = 0x0;
+ table++;
+
+ *table = cpu_to_be32(bcount);
+ table++;
+
+ cur_addr += bcount;
+ cur_len -= bcount;
+ }
+ }
+
+ sg = sg_next(sg);
+ i--;
+ }
+
+ if (count) {
+ table--;
+ *table |= cpu_to_be32(0x80000000);
+ return count;
+ }
+
+ return 0; /* revert to PIO for this request */
+}
+
+static int sgiioc4_dma_setup(ide_drive_t *drive, struct ide_cmd *cmd)
+{
+ int ddir;
+ u8 write = !!(cmd->tf_flags & IDE_TFLAG_WRITE);
+
+ if (sgiioc4_build_dmatable(drive, cmd) == 0)
+ /* try PIO instead of DMA */
+ return 1;
+
+ if (write)
+ /* Writes TO the IOC4 FROM Main Memory */
+ ddir = IOC4_DMA_READ;
+ else
+ /* Writes FROM the IOC4 TO Main Memory */
+ ddir = IOC4_DMA_WRITE;
+
+ sgiioc4_configure_for_dma(ddir, drive);
+
+ return 0;
+}
+
+static const struct ide_tp_ops sgiioc4_tp_ops = {
+ .exec_command = ide_exec_command,
+ .read_status = sgiioc4_read_status,
+ .read_altstatus = ide_read_altstatus,
+ .write_devctl = ide_write_devctl,
+
+ .dev_select = ide_dev_select,
+ .tf_load = ide_tf_load,
+ .tf_read = ide_tf_read,
+
+ .input_data = ide_input_data,
+ .output_data = ide_output_data,
+};
+
+static const struct ide_port_ops sgiioc4_port_ops = {
+ .set_dma_mode = sgiioc4_set_dma_mode,
+ /* reset DMA engine, clear IRQs */
+ .resetproc = sgiioc4_resetproc,
+};
+
+static const struct ide_dma_ops sgiioc4_dma_ops = {
+ .dma_host_set = sgiioc4_dma_host_set,
+ .dma_setup = sgiioc4_dma_setup,
+ .dma_start = sgiioc4_dma_start,
+ .dma_end = sgiioc4_dma_end,
+ .dma_test_irq = sgiioc4_dma_test_irq,
+ .dma_lost_irq = sgiioc4_dma_lost_irq,
+};
+
+static const struct ide_port_info sgiioc4_port_info = {
+ .name = DRV_NAME,
+ .chipset = ide_pci,
+ .init_dma = ide_dma_sgiioc4,
+ .tp_ops = &sgiioc4_tp_ops,
+ .port_ops = &sgiioc4_port_ops,
+ .dma_ops = &sgiioc4_dma_ops,
+ .host_flags = IDE_HFLAG_MMIO,
+ .irq_flags = IRQF_SHARED,
+ .mwdma_mask = ATA_MWDMA2_ONLY,
+};
+
+static int sgiioc4_ide_setup_pci_device(struct pci_dev *dev)
+{
+ unsigned long cmd_base, irqport;
+ unsigned long bar0, cmd_phys_base, ctl;
+ void __iomem *virt_base;
+ struct ide_hw hw, *hws[] = { &hw };
+ int rc;
+
+ /* Get the CmdBlk and CtrlBlk base registers */
+ bar0 = pci_resource_start(dev, 0);
+ virt_base = pci_ioremap_bar(dev, 0);
+ if (virt_base == NULL) {
+ printk(KERN_ERR "%s: Unable to remap BAR 0 address: 0x%lx\n",
+ DRV_NAME, bar0);
+ return -ENOMEM;
+ }
+ cmd_base = (unsigned long)virt_base + IOC4_CMD_OFFSET;
+ ctl = (unsigned long)virt_base + IOC4_CTRL_OFFSET;
+ irqport = (unsigned long)virt_base + IOC4_INTR_OFFSET;
+
+ cmd_phys_base = bar0 + IOC4_CMD_OFFSET;
+ if (request_mem_region(cmd_phys_base, IOC4_CMD_CTL_BLK_SIZE,
+ DRV_NAME) == NULL) {
+ printk(KERN_ERR "%s %s -- ERROR: addresses 0x%08lx to 0x%08lx "
+ "already in use\n", DRV_NAME, pci_name(dev),
+ cmd_phys_base, cmd_phys_base + IOC4_CMD_CTL_BLK_SIZE);
+ rc = -EBUSY;
+ goto req_mem_rgn_err;
+ }
+
+ /* Initialize the IO registers */
+ memset(&hw, 0, sizeof(hw));
+ sgiioc4_init_hwif_ports(&hw, cmd_base, ctl, irqport);
+ hw.irq = dev->irq;
+ hw.dev = &dev->dev;
+
+ /* Initialize chipset IRQ registers */
+ writel(0x03, (void __iomem *)(irqport + IOC4_INTR_SET * 4));
+
+ rc = ide_host_add(&sgiioc4_port_info, hws, 1, NULL);
+ if (!rc)
+ return 0;
+
+ release_mem_region(cmd_phys_base, IOC4_CMD_CTL_BLK_SIZE);
+req_mem_rgn_err:
+ iounmap(virt_base);
+ return rc;
+}
+
+static unsigned int pci_init_sgiioc4(struct pci_dev *dev)
+{
+ int ret;
+
+ printk(KERN_INFO "%s: IDE controller at PCI slot %s, revision %d\n",
+ DRV_NAME, pci_name(dev), dev->revision);
+
+ if (dev->revision < IOC4_SUPPORTED_FIRMWARE_REV) {
+ printk(KERN_ERR "Skipping %s IDE controller in slot %s: "
+ "firmware is obsolete - please upgrade to "
+ "revision46 or higher\n",
+ DRV_NAME, pci_name(dev));
+ ret = -EAGAIN;
+ goto out;
+ }
+ ret = sgiioc4_ide_setup_pci_device(dev);
+out:
+ return ret;
+}
+
+static int ioc4_ide_attach_one(struct ioc4_driver_data *idd)
+{
+ /*
+ * PCI-RT does not bring out IDE connection.
+ * Do not attach to this particular IOC4.
+ */
+ if (idd->idd_variant == IOC4_VARIANT_PCI_RT)
+ return 0;
+
+ return pci_init_sgiioc4(idd->idd_pdev);
+}
+
+static struct ioc4_submodule ioc4_ide_submodule = {
+ .is_name = "IOC4_ide",
+ .is_owner = THIS_MODULE,
+ .is_probe = ioc4_ide_attach_one,
+};
+
+static int __init ioc4_ide_init(void)
+{
+ return ioc4_register_submodule(&ioc4_ide_submodule);
+}
+
+late_initcall(ioc4_ide_init); /* Call only after IDE init is done */
+
+MODULE_AUTHOR("Aniket Malatpure/Jeremy Higdon");
+MODULE_DESCRIPTION("IDE PCI driver module for SGI IOC4 Base-IO Card");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff