Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / drivers / i2c / busses / i2c-iop3xx.h

diff --git a/kernel/drivers/i2c/busses/i2c-iop3xx.h b/kernel/drivers/i2c/busses/i2c-iop3xx.h
new file mode 100644 (file)
index 0000000..2d6929c
--- /dev/null
+++ b/kernel/drivers/i2c/busses/i2c-iop3xx.h
@@ -0,0 +1,103 @@
+/* ------------------------------------------------------------------------- */
+/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c         */
+/* ------------------------------------------------------------------------- */
+/*   Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd
+ *                      <Peter dot Milne at D hyphen TACQ dot com>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation, version 2.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.                            */
+/* ------------------------------------------------------------------------- */
+
+
+#ifndef I2C_IOP3XX_H
+#define I2C_IOP3XX_H 1
+
+/*
+ * iop321 hardware bit definitions
+ */
+#define IOP3XX_ICR_FAST_MODE   0x8000  /* 1=400kBps, 0=100kBps */
+#define IOP3XX_ICR_UNIT_RESET  0x4000  /* 1=RESET */
+#define IOP3XX_ICR_SAD_IE      0x2000  /* 1=Slave Detect Interrupt Enable */
+#define IOP3XX_ICR_ALD_IE      0x1000  /* 1=Arb Loss Detect Interrupt Enable */
+#define IOP3XX_ICR_SSD_IE      0x0800  /* 1=Slave STOP Detect Interrupt Enable */
+#define IOP3XX_ICR_BERR_IE     0x0400  /* 1=Bus Error Interrupt Enable */
+#define IOP3XX_ICR_RXFULL_IE   0x0200  /* 1=Receive Full Interrupt Enable */
+#define IOP3XX_ICR_TXEMPTY_IE  0x0100  /* 1=Transmit Empty Interrupt Enable */
+#define IOP3XX_ICR_GCD         0x0080  /* 1=General Call Disable */
+/*
+ * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set
+ * when sending a master mode general call message from the I2C unit"
+ */
+#define IOP3XX_ICR_UE          0x0040  /* 1=Unit Enable */
+/*
+ * "NOTE: To avoid I2C bus integrity problems, 
+ * the user needs to ensure that the GPIO Output Data Register - 
+ * GPOD bits associated with an I2C port are cleared prior to setting 
+ * the enable bit for that I2C serial port. 
+ * The user prepares to enable I2C port 0 and 
+ * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively.
+ */
+#define IOP3XX_ICR_SCLEN       0x0020  /* 1=SCL enable for master mode */
+#define IOP3XX_ICR_MABORT      0x0010  /* 1=Send a STOP with no data 
+                                        * NB TBYTE must be clear */
+#define IOP3XX_ICR_TBYTE       0x0008  /* 1=Send/Receive a byte. i2c clears */
+#define IOP3XX_ICR_NACK                0x0004  /* 1=reply with NACK */
+#define IOP3XX_ICR_MSTOP       0x0002  /* 1=send a STOP after next data byte */
+#define IOP3XX_ICR_MSTART      0x0001  /* 1=initiate a START */
+
+
+#define IOP3XX_ISR_BERRD       0x0400  /* 1=BUS ERROR Detected */
+#define IOP3XX_ISR_SAD         0x0200  /* 1=Slave ADdress Detected */
+#define IOP3XX_ISR_GCAD                0x0100  /* 1=General Call Address Detected */
+#define IOP3XX_ISR_RXFULL      0x0080  /* 1=Receive Full */
+#define IOP3XX_ISR_TXEMPTY     0x0040  /* 1=Transmit Empty */
+#define IOP3XX_ISR_ALD         0x0020  /* 1=Arbitration Loss Detected */
+#define IOP3XX_ISR_SSD         0x0010  /* 1=Slave STOP Detected */
+#define IOP3XX_ISR_BBUSY       0x0008  /* 1=Bus BUSY */
+#define IOP3XX_ISR_UNITBUSY    0x0004  /* 1=Unit Busy */
+#define IOP3XX_ISR_NACK                0x0002  /* 1=Unit Rx or Tx a NACK */
+#define IOP3XX_ISR_RXREAD      0x0001  /* 1=READ 0=WRITE (R/W bit of slave addr */
+
+#define IOP3XX_ISR_CLEARBITS   0x07f0
+
+#define IOP3XX_ISAR_SAMASK     0x007f
+
+#define IOP3XX_IDBR_MASK       0x00ff
+
+#define IOP3XX_IBMR_SCL                0x0002
+#define IOP3XX_IBMR_SDA                0x0001
+
+#define IOP3XX_GPOD_I2C0       0x00c0  /* clear these bits to enable ch0 */
+#define IOP3XX_GPOD_I2C1       0x0030  /* clear these bits to enable ch1 */
+
+#define MYSAR                  0       /* default slave address */
+
+#define I2C_ERR                        321
+#define I2C_ERR_BERR           (I2C_ERR+0)
+#define I2C_ERR_ALD            (I2C_ERR+1)
+
+
+#define        CR_OFFSET               0
+#define        SR_OFFSET               0x4
+#define        SAR_OFFSET              0x8
+#define        DBR_OFFSET              0xc
+#define        CCR_OFFSET              0x10
+#define        BMR_OFFSET              0x14
+
+#define        IOP3XX_I2C_IO_SIZE      0x18
+
+struct i2c_algo_iop3xx_data {
+       void __iomem *ioaddr;
+       wait_queue_head_t waitq;
+       spinlock_t lock;
+       u32 SR_enabled, SR_received;
+       int id;
+};
+
+#endif /* I2C_IOP3XX_H */