--- /dev/null
+/*
+ * lm90.c - Part of lm_sensors, Linux kernel modules for hardware
+ * monitoring
+ * Copyright (C) 2003-2010 Jean Delvare <jdelvare@suse.de>
+ *
+ * Based on the lm83 driver. The LM90 is a sensor chip made by National
+ * Semiconductor. It reports up to two temperatures (its own plus up to
+ * one external one) with a 0.125 deg resolution (1 deg for local
+ * temperature) and a 3-4 deg accuracy.
+ *
+ * This driver also supports the LM89 and LM99, two other sensor chips
+ * made by National Semiconductor. Both have an increased remote
+ * temperature measurement accuracy (1 degree), and the LM99
+ * additionally shifts remote temperatures (measured and limits) by 16
+ * degrees, which allows for higher temperatures measurement.
+ * Note that there is no way to differentiate between both chips.
+ * When device is auto-detected, the driver will assume an LM99.
+ *
+ * This driver also supports the LM86, another sensor chip made by
+ * National Semiconductor. It is exactly similar to the LM90 except it
+ * has a higher accuracy.
+ *
+ * This driver also supports the ADM1032, a sensor chip made by Analog
+ * Devices. That chip is similar to the LM90, with a few differences
+ * that are not handled by this driver. Among others, it has a higher
+ * accuracy than the LM90, much like the LM86 does.
+ *
+ * This driver also supports the MAX6657, MAX6658 and MAX6659 sensor
+ * chips made by Maxim. These chips are similar to the LM86.
+ * Note that there is no easy way to differentiate between the three
+ * variants. We use the device address to detect MAX6659, which will result
+ * in a detection as max6657 if it is on address 0x4c. The extra address
+ * and features of the MAX6659 are only supported if the chip is configured
+ * explicitly as max6659, or if its address is not 0x4c.
+ * These chips lack the remote temperature offset feature.
+ *
+ * This driver also supports the MAX6646, MAX6647, MAX6648, MAX6649 and
+ * MAX6692 chips made by Maxim. These are again similar to the LM86,
+ * but they use unsigned temperature values and can report temperatures
+ * from 0 to 145 degrees.
+ *
+ * This driver also supports the MAX6680 and MAX6681, two other sensor
+ * chips made by Maxim. These are quite similar to the other Maxim
+ * chips. The MAX6680 and MAX6681 only differ in the pinout so they can
+ * be treated identically.
+ *
+ * This driver also supports the MAX6695 and MAX6696, two other sensor
+ * chips made by Maxim. These are also quite similar to other Maxim
+ * chips, but support three temperature sensors instead of two. MAX6695
+ * and MAX6696 only differ in the pinout so they can be treated identically.
+ *
+ * This driver also supports ADT7461 and ADT7461A from Analog Devices as well as
+ * NCT1008 from ON Semiconductor. The chips are supported in both compatibility
+ * and extended mode. They are mostly compatible with LM90 except for a data
+ * format difference for the temperature value registers.
+ *
+ * This driver also supports the SA56004 from Philips. This device is
+ * pin-compatible with the LM86, the ED/EDP parts are also address-compatible.
+ *
+ * This driver also supports the G781 from GMT. This device is compatible
+ * with the ADM1032.
+ *
+ * This driver also supports TMP451 from Texas Instruments. This device is
+ * supported in both compatibility and extended mode. It's mostly compatible
+ * with ADT7461 except for local temperature low byte register and max
+ * conversion rate.
+ *
+ * Since the LM90 was the first chipset supported by this driver, most
+ * comments will refer to this chipset, but are actually general and
+ * concern all supported chipsets, unless mentioned otherwise.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/hwmon.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/sysfs.h>
+#include <linux/interrupt.h>
+#include <linux/regulator/consumer.h>
+
+/*
+ * Addresses to scan
+ * Address is fully defined internally and cannot be changed except for
+ * MAX6659, MAX6680 and MAX6681.
+ * LM86, LM89, LM90, LM99, ADM1032, ADM1032-1, ADT7461, ADT7461A, MAX6649,
+ * MAX6657, MAX6658, NCT1008 and W83L771 have address 0x4c.
+ * ADM1032-2, ADT7461-2, ADT7461A-2, LM89-1, LM99-1, MAX6646, and NCT1008D
+ * have address 0x4d.
+ * MAX6647 has address 0x4e.
+ * MAX6659 can have address 0x4c, 0x4d or 0x4e.
+ * MAX6680 and MAX6681 can have address 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+ * 0x4c, 0x4d or 0x4e.
+ * SA56004 can have address 0x48 through 0x4F.
+ */
+
+static const unsigned short normal_i2c[] = {
+ 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x48, 0x49, 0x4a, 0x4b, 0x4c,
+ 0x4d, 0x4e, 0x4f, I2C_CLIENT_END };
+
+enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
+ max6646, w83l771, max6696, sa56004, g781, tmp451 };
+
+/*
+ * The LM90 registers
+ */
+
+#define LM90_REG_R_MAN_ID 0xFE
+#define LM90_REG_R_CHIP_ID 0xFF
+#define LM90_REG_R_CONFIG1 0x03
+#define LM90_REG_W_CONFIG1 0x09
+#define LM90_REG_R_CONFIG2 0xBF
+#define LM90_REG_W_CONFIG2 0xBF
+#define LM90_REG_R_CONVRATE 0x04
+#define LM90_REG_W_CONVRATE 0x0A
+#define LM90_REG_R_STATUS 0x02
+#define LM90_REG_R_LOCAL_TEMP 0x00
+#define LM90_REG_R_LOCAL_HIGH 0x05
+#define LM90_REG_W_LOCAL_HIGH 0x0B
+#define LM90_REG_R_LOCAL_LOW 0x06
+#define LM90_REG_W_LOCAL_LOW 0x0C
+#define LM90_REG_R_LOCAL_CRIT 0x20
+#define LM90_REG_W_LOCAL_CRIT 0x20
+#define LM90_REG_R_REMOTE_TEMPH 0x01
+#define LM90_REG_R_REMOTE_TEMPL 0x10
+#define LM90_REG_R_REMOTE_OFFSH 0x11
+#define LM90_REG_W_REMOTE_OFFSH 0x11
+#define LM90_REG_R_REMOTE_OFFSL 0x12
+#define LM90_REG_W_REMOTE_OFFSL 0x12
+#define LM90_REG_R_REMOTE_HIGHH 0x07
+#define LM90_REG_W_REMOTE_HIGHH 0x0D
+#define LM90_REG_R_REMOTE_HIGHL 0x13
+#define LM90_REG_W_REMOTE_HIGHL 0x13
+#define LM90_REG_R_REMOTE_LOWH 0x08
+#define LM90_REG_W_REMOTE_LOWH 0x0E
+#define LM90_REG_R_REMOTE_LOWL 0x14
+#define LM90_REG_W_REMOTE_LOWL 0x14
+#define LM90_REG_R_REMOTE_CRIT 0x19
+#define LM90_REG_W_REMOTE_CRIT 0x19
+#define LM90_REG_R_TCRIT_HYST 0x21
+#define LM90_REG_W_TCRIT_HYST 0x21
+
+/* MAX6646/6647/6649/6657/6658/6659/6695/6696 registers */
+
+#define MAX6657_REG_R_LOCAL_TEMPL 0x11
+#define MAX6696_REG_R_STATUS2 0x12
+#define MAX6659_REG_R_REMOTE_EMERG 0x16
+#define MAX6659_REG_W_REMOTE_EMERG 0x16
+#define MAX6659_REG_R_LOCAL_EMERG 0x17
+#define MAX6659_REG_W_LOCAL_EMERG 0x17
+
+/* SA56004 registers */
+
+#define SA56004_REG_R_LOCAL_TEMPL 0x22
+
+#define LM90_DEF_CONVRATE_RVAL 6 /* Def conversion rate register value */
+#define LM90_MAX_CONVRATE_MS 16000 /* Maximum conversion rate in ms */
+
+/* TMP451 registers */
+#define TMP451_REG_R_LOCAL_TEMPL 0x15
+
+/*
+ * Device flags
+ */
+#define LM90_FLAG_ADT7461_EXT (1 << 0) /* ADT7461 extended mode */
+/* Device features */
+#define LM90_HAVE_OFFSET (1 << 1) /* temperature offset register */
+#define LM90_HAVE_REM_LIMIT_EXT (1 << 3) /* extended remote limit */
+#define LM90_HAVE_EMERGENCY (1 << 4) /* 3rd upper (emergency) limit */
+#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */
+#define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
+#define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
+
+/* LM90 status */
+#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
+#define LM90_STATUS_RTHRM (1 << 1) /* remote THERM limit tripped */
+#define LM90_STATUS_ROPEN (1 << 2) /* remote is an open circuit */
+#define LM90_STATUS_RLOW (1 << 3) /* remote low temp limit tripped */
+#define LM90_STATUS_RHIGH (1 << 4) /* remote high temp limit tripped */
+#define LM90_STATUS_LLOW (1 << 5) /* local low temp limit tripped */
+#define LM90_STATUS_LHIGH (1 << 6) /* local high temp limit tripped */
+
+#define MAX6696_STATUS2_R2THRM (1 << 1) /* remote2 THERM limit tripped */
+#define MAX6696_STATUS2_R2OPEN (1 << 2) /* remote2 is an open circuit */
+#define MAX6696_STATUS2_R2LOW (1 << 3) /* remote2 low temp limit tripped */
+#define MAX6696_STATUS2_R2HIGH (1 << 4) /* remote2 high temp limit tripped */
+#define MAX6696_STATUS2_ROT2 (1 << 5) /* remote emergency limit tripped */
+#define MAX6696_STATUS2_R2OT2 (1 << 6) /* remote2 emergency limit tripped */
+#define MAX6696_STATUS2_LOT2 (1 << 7) /* local emergency limit tripped */
+
+/*
+ * Driver data (common to all clients)
+ */
+
+static const struct i2c_device_id lm90_id[] = {
+ { "adm1032", adm1032 },
+ { "adt7461", adt7461 },
+ { "adt7461a", adt7461 },
+ { "g781", g781 },
+ { "lm90", lm90 },
+ { "lm86", lm86 },
+ { "lm89", lm86 },
+ { "lm99", lm99 },
+ { "max6646", max6646 },
+ { "max6647", max6646 },
+ { "max6649", max6646 },
+ { "max6657", max6657 },
+ { "max6658", max6657 },
+ { "max6659", max6659 },
+ { "max6680", max6680 },
+ { "max6681", max6680 },
+ { "max6695", max6696 },
+ { "max6696", max6696 },
+ { "nct1008", adt7461 },
+ { "w83l771", w83l771 },
+ { "sa56004", sa56004 },
+ { "tmp451", tmp451 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, lm90_id);
+
+/*
+ * chip type specific parameters
+ */
+struct lm90_params {
+ u32 flags; /* Capabilities */
+ u16 alert_alarms; /* Which alarm bits trigger ALERT# */
+ /* Upper 8 bits for max6695/96 */
+ u8 max_convrate; /* Maximum conversion rate register value */
+ u8 reg_local_ext; /* Extended local temp register (optional) */
+};
+
+static const struct lm90_params lm90_params[] = {
+ [adm1032] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+ | LM90_HAVE_BROKEN_ALERT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 10,
+ },
+ [adt7461] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+ | LM90_HAVE_BROKEN_ALERT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 10,
+ },
+ [g781] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+ | LM90_HAVE_BROKEN_ALERT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ },
+ [lm86] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [lm90] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [lm99] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ },
+ [max6646] = {
+ .alert_alarms = 0x7c,
+ .max_convrate = 6,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6657] = {
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6659] = {
+ .flags = LM90_HAVE_EMERGENCY,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [max6680] = {
+ .flags = LM90_HAVE_OFFSET,
+ .alert_alarms = 0x7c,
+ .max_convrate = 7,
+ },
+ [max6696] = {
+ .flags = LM90_HAVE_EMERGENCY
+ | LM90_HAVE_EMERGENCY_ALARM | LM90_HAVE_TEMP3,
+ .alert_alarms = 0x1c7c,
+ .max_convrate = 6,
+ .reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
+ },
+ [w83l771] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 8,
+ },
+ [sa56004] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT,
+ .alert_alarms = 0x7b,
+ .max_convrate = 9,
+ .reg_local_ext = SA56004_REG_R_LOCAL_TEMPL,
+ },
+ [tmp451] = {
+ .flags = LM90_HAVE_OFFSET | LM90_HAVE_REM_LIMIT_EXT
+ | LM90_HAVE_BROKEN_ALERT,
+ .alert_alarms = 0x7c,
+ .max_convrate = 9,
+ .reg_local_ext = TMP451_REG_R_LOCAL_TEMPL,
+ }
+};
+
+/*
+ * TEMP8 register index
+ */
+enum lm90_temp8_reg_index {
+ LOCAL_LOW = 0,
+ LOCAL_HIGH,
+ LOCAL_CRIT,
+ REMOTE_CRIT,
+ LOCAL_EMERG, /* max6659 and max6695/96 */
+ REMOTE_EMERG, /* max6659 and max6695/96 */
+ REMOTE2_CRIT, /* max6695/96 only */
+ REMOTE2_EMERG, /* max6695/96 only */
+ TEMP8_REG_NUM
+};
+
+/*
+ * TEMP11 register index
+ */
+enum lm90_temp11_reg_index {
+ REMOTE_TEMP = 0,
+ REMOTE_LOW,
+ REMOTE_HIGH,
+ REMOTE_OFFSET, /* except max6646, max6657/58/59, and max6695/96 */
+ LOCAL_TEMP,
+ REMOTE2_TEMP, /* max6695/96 only */
+ REMOTE2_LOW, /* max6695/96 only */
+ REMOTE2_HIGH, /* max6695/96 only */
+ TEMP11_REG_NUM
+};
+
+/*
+ * Client data (each client gets its own)
+ */
+
+struct lm90_data {
+ struct i2c_client *client;
+ struct device *hwmon_dev;
+ const struct attribute_group *groups[6];
+ struct mutex update_lock;
+ struct regulator *regulator;
+ char valid; /* zero until following fields are valid */
+ unsigned long last_updated; /* in jiffies */
+ int kind;
+ u32 flags;
+
+ int update_interval; /* in milliseconds */
+
+ u8 config_orig; /* Original configuration register value */
+ u8 convrate_orig; /* Original conversion rate register value */
+ u16 alert_alarms; /* Which alarm bits trigger ALERT# */
+ /* Upper 8 bits for max6695/96 */
+ u8 max_convrate; /* Maximum conversion rate */
+ u8 reg_local_ext; /* local extension register offset */
+
+ /* registers values */
+ s8 temp8[TEMP8_REG_NUM];
+ s16 temp11[TEMP11_REG_NUM];
+ u8 temp_hyst;
+ u16 alarms; /* bitvector (upper 8 bits for max6695/96) */
+};
+
+/*
+ * Support functions
+ */
+
+/*
+ * The ADM1032 supports PEC but not on write byte transactions, so we need
+ * to explicitly ask for a transaction without PEC.
+ */
+static inline s32 adm1032_write_byte(struct i2c_client *client, u8 value)
+{
+ return i2c_smbus_xfer(client->adapter, client->addr,
+ client->flags & ~I2C_CLIENT_PEC,
+ I2C_SMBUS_WRITE, value, I2C_SMBUS_BYTE, NULL);
+}
+
+/*
+ * It is assumed that client->update_lock is held (unless we are in
+ * detection or initialization steps). This matters when PEC is enabled,
+ * because we don't want the address pointer to change between the write
+ * byte and the read byte transactions.
+ */
+static int lm90_read_reg(struct i2c_client *client, u8 reg, u8 *value)
+{
+ int err;
+
+ if (client->flags & I2C_CLIENT_PEC) {
+ err = adm1032_write_byte(client, reg);
+ if (err >= 0)
+ err = i2c_smbus_read_byte(client);
+ } else
+ err = i2c_smbus_read_byte_data(client, reg);
+
+ if (err < 0) {
+ dev_warn(&client->dev, "Register %#02x read failed (%d)\n",
+ reg, err);
+ return err;
+ }
+ *value = err;
+
+ return 0;
+}
+
+static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value)
+{
+ int err;
+ u8 oldh, newh, l;
+
+ /*
+ * There is a trick here. We have to read two registers to have the
+ * sensor temperature, but we have to beware a conversion could occur
+ * between the readings. The datasheet says we should either use
+ * the one-shot conversion register, which we don't want to do
+ * (disables hardware monitoring) or monitor the busy bit, which is
+ * impossible (we can't read the values and monitor that bit at the
+ * exact same time). So the solution used here is to read the high
+ * byte once, then the low byte, then the high byte again. If the new
+ * high byte matches the old one, then we have a valid reading. Else
+ * we have to read the low byte again, and now we believe we have a
+ * correct reading.
+ */
+ if ((err = lm90_read_reg(client, regh, &oldh))
+ || (err = lm90_read_reg(client, regl, &l))
+ || (err = lm90_read_reg(client, regh, &newh)))
+ return err;
+ if (oldh != newh) {
+ err = lm90_read_reg(client, regl, &l);
+ if (err)
+ return err;
+ }
+ *value = (newh << 8) | l;
+
+ return 0;
+}
+
+/*
+ * client->update_lock must be held when calling this function (unless we are
+ * in detection or initialization steps), and while a remote channel other
+ * than channel 0 is selected. Also, calling code must make sure to re-select
+ * external channel 0 before releasing the lock. This is necessary because
+ * various registers have different meanings as a result of selecting a
+ * non-default remote channel.
+ */
+static inline void lm90_select_remote_channel(struct i2c_client *client,
+ struct lm90_data *data,
+ int channel)
+{
+ u8 config;
+
+ if (data->kind == max6696) {
+ lm90_read_reg(client, LM90_REG_R_CONFIG1, &config);
+ config &= ~0x08;
+ if (channel)
+ config |= 0x08;
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
+ config);
+ }
+}
+
+/*
+ * Set conversion rate.
+ * client->update_lock must be held when calling this function (unless we are
+ * in detection or initialization steps).
+ */
+static void lm90_set_convrate(struct i2c_client *client, struct lm90_data *data,
+ unsigned int interval)
+{
+ int i;
+ unsigned int update_interval;
+
+ /* Shift calculations to avoid rounding errors */
+ interval <<= 6;
+
+ /* find the nearest update rate */
+ for (i = 0, update_interval = LM90_MAX_CONVRATE_MS << 6;
+ i < data->max_convrate; i++, update_interval >>= 1)
+ if (interval >= update_interval * 3 / 4)
+ break;
+
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, i);
+ data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64);
+}
+
+static struct lm90_data *lm90_update_device(struct device *dev)
+{
+ struct lm90_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ unsigned long next_update;
+
+ mutex_lock(&data->update_lock);
+
+ next_update = data->last_updated +
+ msecs_to_jiffies(data->update_interval);
+ if (time_after(jiffies, next_update) || !data->valid) {
+ u8 h, l;
+ u8 alarms;
+
+ dev_dbg(&client->dev, "Updating lm90 data.\n");
+ lm90_read_reg(client, LM90_REG_R_LOCAL_LOW,
+ &data->temp8[LOCAL_LOW]);
+ lm90_read_reg(client, LM90_REG_R_LOCAL_HIGH,
+ &data->temp8[LOCAL_HIGH]);
+ lm90_read_reg(client, LM90_REG_R_LOCAL_CRIT,
+ &data->temp8[LOCAL_CRIT]);
+ lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT,
+ &data->temp8[REMOTE_CRIT]);
+ lm90_read_reg(client, LM90_REG_R_TCRIT_HYST, &data->temp_hyst);
+
+ if (data->reg_local_ext) {
+ lm90_read16(client, LM90_REG_R_LOCAL_TEMP,
+ data->reg_local_ext,
+ &data->temp11[LOCAL_TEMP]);
+ } else {
+ if (lm90_read_reg(client, LM90_REG_R_LOCAL_TEMP,
+ &h) == 0)
+ data->temp11[LOCAL_TEMP] = h << 8;
+ }
+ lm90_read16(client, LM90_REG_R_REMOTE_TEMPH,
+ LM90_REG_R_REMOTE_TEMPL,
+ &data->temp11[REMOTE_TEMP]);
+
+ if (lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h) == 0) {
+ data->temp11[REMOTE_LOW] = h << 8;
+ if ((data->flags & LM90_HAVE_REM_LIMIT_EXT)
+ && lm90_read_reg(client, LM90_REG_R_REMOTE_LOWL,
+ &l) == 0)
+ data->temp11[REMOTE_LOW] |= l;
+ }
+ if (lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h) == 0) {
+ data->temp11[REMOTE_HIGH] = h << 8;
+ if ((data->flags & LM90_HAVE_REM_LIMIT_EXT)
+ && lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHL,
+ &l) == 0)
+ data->temp11[REMOTE_HIGH] |= l;
+ }
+
+ if (data->flags & LM90_HAVE_OFFSET) {
+ if (lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSH,
+ &h) == 0
+ && lm90_read_reg(client, LM90_REG_R_REMOTE_OFFSL,
+ &l) == 0)
+ data->temp11[REMOTE_OFFSET] = (h << 8) | l;
+ }
+ if (data->flags & LM90_HAVE_EMERGENCY) {
+ lm90_read_reg(client, MAX6659_REG_R_LOCAL_EMERG,
+ &data->temp8[LOCAL_EMERG]);
+ lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG,
+ &data->temp8[REMOTE_EMERG]);
+ }
+ lm90_read_reg(client, LM90_REG_R_STATUS, &alarms);
+ data->alarms = alarms; /* save as 16 bit value */
+
+ if (data->kind == max6696) {
+ lm90_select_remote_channel(client, data, 1);
+ lm90_read_reg(client, LM90_REG_R_REMOTE_CRIT,
+ &data->temp8[REMOTE2_CRIT]);
+ lm90_read_reg(client, MAX6659_REG_R_REMOTE_EMERG,
+ &data->temp8[REMOTE2_EMERG]);
+ lm90_read16(client, LM90_REG_R_REMOTE_TEMPH,
+ LM90_REG_R_REMOTE_TEMPL,
+ &data->temp11[REMOTE2_TEMP]);
+ if (!lm90_read_reg(client, LM90_REG_R_REMOTE_LOWH, &h))
+ data->temp11[REMOTE2_LOW] = h << 8;
+ if (!lm90_read_reg(client, LM90_REG_R_REMOTE_HIGHH, &h))
+ data->temp11[REMOTE2_HIGH] = h << 8;
+ lm90_select_remote_channel(client, data, 0);
+
+ if (!lm90_read_reg(client, MAX6696_REG_R_STATUS2,
+ &alarms))
+ data->alarms |= alarms << 8;
+ }
+
+ /*
+ * Re-enable ALERT# output if it was originally enabled and
+ * relevant alarms are all clear
+ */
+ if ((data->config_orig & 0x80) == 0
+ && (data->alarms & data->alert_alarms) == 0) {
+ u8 config;
+
+ lm90_read_reg(client, LM90_REG_R_CONFIG1, &config);
+ if (config & 0x80) {
+ dev_dbg(&client->dev, "Re-enabling ALERT#\n");
+ i2c_smbus_write_byte_data(client,
+ LM90_REG_W_CONFIG1,
+ config & ~0x80);
+ }
+ }
+
+ data->last_updated = jiffies;
+ data->valid = 1;
+ }
+
+ mutex_unlock(&data->update_lock);
+
+ return data;
+}
+
+/*
+ * Conversions
+ * For local temperatures and limits, critical limits and the hysteresis
+ * value, the LM90 uses signed 8-bit values with LSB = 1 degree Celsius.
+ * For remote temperatures and limits, it uses signed 11-bit values with
+ * LSB = 0.125 degree Celsius, left-justified in 16-bit registers. Some
+ * Maxim chips use unsigned values.
+ */
+
+static inline int temp_from_s8(s8 val)
+{
+ return val * 1000;
+}
+
+static inline int temp_from_u8(u8 val)
+{
+ return val * 1000;
+}
+
+static inline int temp_from_s16(s16 val)
+{
+ return val / 32 * 125;
+}
+
+static inline int temp_from_u16(u16 val)
+{
+ return val / 32 * 125;
+}
+
+static s8 temp_to_s8(long val)
+{
+ if (val <= -128000)
+ return -128;
+ if (val >= 127000)
+ return 127;
+ if (val < 0)
+ return (val - 500) / 1000;
+ return (val + 500) / 1000;
+}
+
+static u8 temp_to_u8(long val)
+{
+ if (val <= 0)
+ return 0;
+ if (val >= 255000)
+ return 255;
+ return (val + 500) / 1000;
+}
+
+static s16 temp_to_s16(long val)
+{
+ if (val <= -128000)
+ return 0x8000;
+ if (val >= 127875)
+ return 0x7FE0;
+ if (val < 0)
+ return (val - 62) / 125 * 32;
+ return (val + 62) / 125 * 32;
+}
+
+static u8 hyst_to_reg(long val)
+{
+ if (val <= 0)
+ return 0;
+ if (val >= 30500)
+ return 31;
+ return (val + 500) / 1000;
+}
+
+/*
+ * ADT7461 in compatibility mode is almost identical to LM90 except that
+ * attempts to write values that are outside the range 0 < temp < 127 are
+ * treated as the boundary value.
+ *
+ * ADT7461 in "extended mode" operation uses unsigned integers offset by
+ * 64 (e.g., 0 -> -64 degC). The range is restricted to -64..191 degC.
+ */
+static inline int temp_from_u8_adt7461(struct lm90_data *data, u8 val)
+{
+ if (data->flags & LM90_FLAG_ADT7461_EXT)
+ return (val - 64) * 1000;
+ else
+ return temp_from_s8(val);
+}
+
+static inline int temp_from_u16_adt7461(struct lm90_data *data, u16 val)
+{
+ if (data->flags & LM90_FLAG_ADT7461_EXT)
+ return (val - 0x4000) / 64 * 250;
+ else
+ return temp_from_s16(val);
+}
+
+static u8 temp_to_u8_adt7461(struct lm90_data *data, long val)
+{
+ if (data->flags & LM90_FLAG_ADT7461_EXT) {
+ if (val <= -64000)
+ return 0;
+ if (val >= 191000)
+ return 0xFF;
+ return (val + 500 + 64000) / 1000;
+ } else {
+ if (val <= 0)
+ return 0;
+ if (val >= 127000)
+ return 127;
+ return (val + 500) / 1000;
+ }
+}
+
+static u16 temp_to_u16_adt7461(struct lm90_data *data, long val)
+{
+ if (data->flags & LM90_FLAG_ADT7461_EXT) {
+ if (val <= -64000)
+ return 0;
+ if (val >= 191750)
+ return 0xFFC0;
+ return (val + 64000 + 125) / 250 * 64;
+ } else {
+ if (val <= 0)
+ return 0;
+ if (val >= 127750)
+ return 0x7FC0;
+ return (val + 125) / 250 * 64;
+ }
+}
+
+/*
+ * Sysfs stuff
+ */
+
+static ssize_t show_temp8(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct lm90_data *data = lm90_update_device(dev);
+ int temp;
+
+ if (data->kind == adt7461 || data->kind == tmp451)
+ temp = temp_from_u8_adt7461(data, data->temp8[attr->index]);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(data->temp8[attr->index]);
+ else
+ temp = temp_from_s8(data->temp8[attr->index]);
+
+ /* +16 degrees offset for temp2 for the LM99 */
+ if (data->kind == lm99 && attr->index == 3)
+ temp += 16000;
+
+ return sprintf(buf, "%d\n", temp);
+}
+
+static ssize_t set_temp8(struct device *dev, struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ static const u8 reg[TEMP8_REG_NUM] = {
+ LM90_REG_W_LOCAL_LOW,
+ LM90_REG_W_LOCAL_HIGH,
+ LM90_REG_W_LOCAL_CRIT,
+ LM90_REG_W_REMOTE_CRIT,
+ MAX6659_REG_W_LOCAL_EMERG,
+ MAX6659_REG_W_REMOTE_EMERG,
+ LM90_REG_W_REMOTE_CRIT,
+ MAX6659_REG_W_REMOTE_EMERG,
+ };
+
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct lm90_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ int nr = attr->index;
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err < 0)
+ return err;
+
+ /* +16 degrees offset for temp2 for the LM99 */
+ if (data->kind == lm99 && attr->index == 3)
+ val -= 16000;
+
+ mutex_lock(&data->update_lock);
+ if (data->kind == adt7461 || data->kind == tmp451)
+ data->temp8[nr] = temp_to_u8_adt7461(data, val);
+ else if (data->kind == max6646)
+ data->temp8[nr] = temp_to_u8(val);
+ else
+ data->temp8[nr] = temp_to_s8(val);
+
+ lm90_select_remote_channel(client, data, nr >= 6);
+ i2c_smbus_write_byte_data(client, reg[nr], data->temp8[nr]);
+ lm90_select_remote_channel(client, data, 0);
+
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t show_temp11(struct device *dev, struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct lm90_data *data = lm90_update_device(dev);
+ int temp;
+
+ if (data->kind == adt7461 || data->kind == tmp451)
+ temp = temp_from_u16_adt7461(data, data->temp11[attr->index]);
+ else if (data->kind == max6646)
+ temp = temp_from_u16(data->temp11[attr->index]);
+ else
+ temp = temp_from_s16(data->temp11[attr->index]);
+
+ /* +16 degrees offset for temp2 for the LM99 */
+ if (data->kind == lm99 && attr->index <= 2)
+ temp += 16000;
+
+ return sprintf(buf, "%d\n", temp);
+}
+
+static ssize_t set_temp11(struct device *dev, struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct {
+ u8 high;
+ u8 low;
+ int channel;
+ } reg[5] = {
+ { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 0 },
+ { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 0 },
+ { LM90_REG_W_REMOTE_OFFSH, LM90_REG_W_REMOTE_OFFSL, 0 },
+ { LM90_REG_W_REMOTE_LOWH, LM90_REG_W_REMOTE_LOWL, 1 },
+ { LM90_REG_W_REMOTE_HIGHH, LM90_REG_W_REMOTE_HIGHL, 1 }
+ };
+
+ struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+ struct lm90_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ int nr = attr->nr;
+ int index = attr->index;
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err < 0)
+ return err;
+
+ /* +16 degrees offset for temp2 for the LM99 */
+ if (data->kind == lm99 && index <= 2)
+ val -= 16000;
+
+ mutex_lock(&data->update_lock);
+ if (data->kind == adt7461 || data->kind == tmp451)
+ data->temp11[index] = temp_to_u16_adt7461(data, val);
+ else if (data->kind == max6646)
+ data->temp11[index] = temp_to_u8(val) << 8;
+ else if (data->flags & LM90_HAVE_REM_LIMIT_EXT)
+ data->temp11[index] = temp_to_s16(val);
+ else
+ data->temp11[index] = temp_to_s8(val) << 8;
+
+ lm90_select_remote_channel(client, data, reg[nr].channel);
+ i2c_smbus_write_byte_data(client, reg[nr].high,
+ data->temp11[index] >> 8);
+ if (data->flags & LM90_HAVE_REM_LIMIT_EXT)
+ i2c_smbus_write_byte_data(client, reg[nr].low,
+ data->temp11[index] & 0xff);
+ lm90_select_remote_channel(client, data, 0);
+
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t show_temphyst(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct lm90_data *data = lm90_update_device(dev);
+ int temp;
+
+ if (data->kind == adt7461 || data->kind == tmp451)
+ temp = temp_from_u8_adt7461(data, data->temp8[attr->index]);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(data->temp8[attr->index]);
+ else
+ temp = temp_from_s8(data->temp8[attr->index]);
+
+ /* +16 degrees offset for temp2 for the LM99 */
+ if (data->kind == lm99 && attr->index == 3)
+ temp += 16000;
+
+ return sprintf(buf, "%d\n", temp - temp_from_s8(data->temp_hyst));
+}
+
+static ssize_t set_temphyst(struct device *dev, struct device_attribute *dummy,
+ const char *buf, size_t count)
+{
+ struct lm90_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ long val;
+ int err;
+ int temp;
+
+ err = kstrtol(buf, 10, &val);
+ if (err < 0)
+ return err;
+
+ mutex_lock(&data->update_lock);
+ if (data->kind == adt7461 || data->kind == tmp451)
+ temp = temp_from_u8_adt7461(data, data->temp8[LOCAL_CRIT]);
+ else if (data->kind == max6646)
+ temp = temp_from_u8(data->temp8[LOCAL_CRIT]);
+ else
+ temp = temp_from_s8(data->temp8[LOCAL_CRIT]);
+
+ data->temp_hyst = hyst_to_reg(temp - val);
+ i2c_smbus_write_byte_data(client, LM90_REG_W_TCRIT_HYST,
+ data->temp_hyst);
+ mutex_unlock(&data->update_lock);
+ return count;
+}
+
+static ssize_t show_alarms(struct device *dev, struct device_attribute *dummy,
+ char *buf)
+{
+ struct lm90_data *data = lm90_update_device(dev);
+ return sprintf(buf, "%d\n", data->alarms);
+}
+
+static ssize_t show_alarm(struct device *dev, struct device_attribute
+ *devattr, char *buf)
+{
+ struct sensor_device_attribute *attr = to_sensor_dev_attr(devattr);
+ struct lm90_data *data = lm90_update_device(dev);
+ int bitnr = attr->index;
+
+ return sprintf(buf, "%d\n", (data->alarms >> bitnr) & 1);
+}
+
+static ssize_t show_update_interval(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct lm90_data *data = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", data->update_interval);
+}
+
+static ssize_t set_update_interval(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct lm90_data *data = dev_get_drvdata(dev);
+ struct i2c_client *client = data->client;
+ unsigned long val;
+ int err;
+
+ err = kstrtoul(buf, 10, &val);
+ if (err)
+ return err;
+
+ mutex_lock(&data->update_lock);
+ lm90_set_convrate(client, data, clamp_val(val, 0, 100000));
+ mutex_unlock(&data->update_lock);
+
+ return count;
+}
+
+static SENSOR_DEVICE_ATTR_2(temp1_input, S_IRUGO, show_temp11, NULL,
+ 0, LOCAL_TEMP);
+static SENSOR_DEVICE_ATTR_2(temp2_input, S_IRUGO, show_temp11, NULL,
+ 0, REMOTE_TEMP);
+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, LOCAL_LOW);
+static SENSOR_DEVICE_ATTR_2(temp2_min, S_IWUSR | S_IRUGO, show_temp11,
+ set_temp11, 0, REMOTE_LOW);
+static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, LOCAL_HIGH);
+static SENSOR_DEVICE_ATTR_2(temp2_max, S_IWUSR | S_IRUGO, show_temp11,
+ set_temp11, 1, REMOTE_HIGH);
+static SENSOR_DEVICE_ATTR(temp1_crit, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, LOCAL_CRIT);
+static SENSOR_DEVICE_ATTR(temp2_crit, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, REMOTE_CRIT);
+static SENSOR_DEVICE_ATTR(temp1_crit_hyst, S_IWUSR | S_IRUGO, show_temphyst,
+ set_temphyst, LOCAL_CRIT);
+static SENSOR_DEVICE_ATTR(temp2_crit_hyst, S_IRUGO, show_temphyst, NULL,
+ REMOTE_CRIT);
+static SENSOR_DEVICE_ATTR_2(temp2_offset, S_IWUSR | S_IRUGO, show_temp11,
+ set_temp11, 2, REMOTE_OFFSET);
+
+/* Individual alarm files */
+static SENSOR_DEVICE_ATTR(temp1_crit_alarm, S_IRUGO, show_alarm, NULL, 0);
+static SENSOR_DEVICE_ATTR(temp2_crit_alarm, S_IRUGO, show_alarm, NULL, 1);
+static SENSOR_DEVICE_ATTR(temp2_fault, S_IRUGO, show_alarm, NULL, 2);
+static SENSOR_DEVICE_ATTR(temp2_min_alarm, S_IRUGO, show_alarm, NULL, 3);
+static SENSOR_DEVICE_ATTR(temp2_max_alarm, S_IRUGO, show_alarm, NULL, 4);
+static SENSOR_DEVICE_ATTR(temp1_min_alarm, S_IRUGO, show_alarm, NULL, 5);
+static SENSOR_DEVICE_ATTR(temp1_max_alarm, S_IRUGO, show_alarm, NULL, 6);
+/* Raw alarm file for compatibility */
+static DEVICE_ATTR(alarms, S_IRUGO, show_alarms, NULL);
+
+static DEVICE_ATTR(update_interval, S_IRUGO | S_IWUSR, show_update_interval,
+ set_update_interval);
+
+static struct attribute *lm90_attributes[] = {
+ &sensor_dev_attr_temp1_input.dev_attr.attr,
+ &sensor_dev_attr_temp2_input.dev_attr.attr,
+ &sensor_dev_attr_temp1_min.dev_attr.attr,
+ &sensor_dev_attr_temp2_min.dev_attr.attr,
+ &sensor_dev_attr_temp1_max.dev_attr.attr,
+ &sensor_dev_attr_temp2_max.dev_attr.attr,
+ &sensor_dev_attr_temp1_crit.dev_attr.attr,
+ &sensor_dev_attr_temp2_crit.dev_attr.attr,
+ &sensor_dev_attr_temp1_crit_hyst.dev_attr.attr,
+ &sensor_dev_attr_temp2_crit_hyst.dev_attr.attr,
+
+ &sensor_dev_attr_temp1_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_fault.dev_attr.attr,
+ &sensor_dev_attr_temp2_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_max_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp1_max_alarm.dev_attr.attr,
+ &dev_attr_alarms.attr,
+ &dev_attr_update_interval.attr,
+ NULL
+};
+
+static const struct attribute_group lm90_group = {
+ .attrs = lm90_attributes,
+};
+
+static struct attribute *lm90_temp2_offset_attributes[] = {
+ &sensor_dev_attr_temp2_offset.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group lm90_temp2_offset_group = {
+ .attrs = lm90_temp2_offset_attributes,
+};
+
+/*
+ * Additional attributes for devices with emergency sensors
+ */
+static SENSOR_DEVICE_ATTR(temp1_emergency, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, LOCAL_EMERG);
+static SENSOR_DEVICE_ATTR(temp2_emergency, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, REMOTE_EMERG);
+static SENSOR_DEVICE_ATTR(temp1_emergency_hyst, S_IRUGO, show_temphyst,
+ NULL, LOCAL_EMERG);
+static SENSOR_DEVICE_ATTR(temp2_emergency_hyst, S_IRUGO, show_temphyst,
+ NULL, REMOTE_EMERG);
+
+static struct attribute *lm90_emergency_attributes[] = {
+ &sensor_dev_attr_temp1_emergency.dev_attr.attr,
+ &sensor_dev_attr_temp2_emergency.dev_attr.attr,
+ &sensor_dev_attr_temp1_emergency_hyst.dev_attr.attr,
+ &sensor_dev_attr_temp2_emergency_hyst.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group lm90_emergency_group = {
+ .attrs = lm90_emergency_attributes,
+};
+
+static SENSOR_DEVICE_ATTR(temp1_emergency_alarm, S_IRUGO, show_alarm, NULL, 15);
+static SENSOR_DEVICE_ATTR(temp2_emergency_alarm, S_IRUGO, show_alarm, NULL, 13);
+
+static struct attribute *lm90_emergency_alarm_attributes[] = {
+ &sensor_dev_attr_temp1_emergency_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp2_emergency_alarm.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group lm90_emergency_alarm_group = {
+ .attrs = lm90_emergency_alarm_attributes,
+};
+
+/*
+ * Additional attributes for devices with 3 temperature sensors
+ */
+static SENSOR_DEVICE_ATTR_2(temp3_input, S_IRUGO, show_temp11, NULL,
+ 0, REMOTE2_TEMP);
+static SENSOR_DEVICE_ATTR_2(temp3_min, S_IWUSR | S_IRUGO, show_temp11,
+ set_temp11, 3, REMOTE2_LOW);
+static SENSOR_DEVICE_ATTR_2(temp3_max, S_IWUSR | S_IRUGO, show_temp11,
+ set_temp11, 4, REMOTE2_HIGH);
+static SENSOR_DEVICE_ATTR(temp3_crit, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, REMOTE2_CRIT);
+static SENSOR_DEVICE_ATTR(temp3_crit_hyst, S_IRUGO, show_temphyst, NULL,
+ REMOTE2_CRIT);
+static SENSOR_DEVICE_ATTR(temp3_emergency, S_IWUSR | S_IRUGO, show_temp8,
+ set_temp8, REMOTE2_EMERG);
+static SENSOR_DEVICE_ATTR(temp3_emergency_hyst, S_IRUGO, show_temphyst,
+ NULL, REMOTE2_EMERG);
+
+static SENSOR_DEVICE_ATTR(temp3_crit_alarm, S_IRUGO, show_alarm, NULL, 9);
+static SENSOR_DEVICE_ATTR(temp3_fault, S_IRUGO, show_alarm, NULL, 10);
+static SENSOR_DEVICE_ATTR(temp3_min_alarm, S_IRUGO, show_alarm, NULL, 11);
+static SENSOR_DEVICE_ATTR(temp3_max_alarm, S_IRUGO, show_alarm, NULL, 12);
+static SENSOR_DEVICE_ATTR(temp3_emergency_alarm, S_IRUGO, show_alarm, NULL, 14);
+
+static struct attribute *lm90_temp3_attributes[] = {
+ &sensor_dev_attr_temp3_input.dev_attr.attr,
+ &sensor_dev_attr_temp3_min.dev_attr.attr,
+ &sensor_dev_attr_temp3_max.dev_attr.attr,
+ &sensor_dev_attr_temp3_crit.dev_attr.attr,
+ &sensor_dev_attr_temp3_crit_hyst.dev_attr.attr,
+ &sensor_dev_attr_temp3_emergency.dev_attr.attr,
+ &sensor_dev_attr_temp3_emergency_hyst.dev_attr.attr,
+
+ &sensor_dev_attr_temp3_fault.dev_attr.attr,
+ &sensor_dev_attr_temp3_min_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_max_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_crit_alarm.dev_attr.attr,
+ &sensor_dev_attr_temp3_emergency_alarm.dev_attr.attr,
+ NULL
+};
+
+static const struct attribute_group lm90_temp3_group = {
+ .attrs = lm90_temp3_attributes,
+};
+
+/* pec used for ADM1032 only */
+static ssize_t show_pec(struct device *dev, struct device_attribute *dummy,
+ char *buf)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ return sprintf(buf, "%d\n", !!(client->flags & I2C_CLIENT_PEC));
+}
+
+static ssize_t set_pec(struct device *dev, struct device_attribute *dummy,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ long val;
+ int err;
+
+ err = kstrtol(buf, 10, &val);
+ if (err < 0)
+ return err;
+
+ switch (val) {
+ case 0:
+ client->flags &= ~I2C_CLIENT_PEC;
+ break;
+ case 1:
+ client->flags |= I2C_CLIENT_PEC;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return count;
+}
+
+static DEVICE_ATTR(pec, S_IWUSR | S_IRUGO, show_pec, set_pec);
+
+/*
+ * Real code
+ */
+
+/* Return 0 if detection is successful, -ENODEV otherwise */
+static int lm90_detect(struct i2c_client *client,
+ struct i2c_board_info *info)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ int address = client->addr;
+ const char *name = NULL;
+ int man_id, chip_id, config1, config2, convrate;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
+ return -ENODEV;
+
+ /* detection and identification */
+ man_id = i2c_smbus_read_byte_data(client, LM90_REG_R_MAN_ID);
+ chip_id = i2c_smbus_read_byte_data(client, LM90_REG_R_CHIP_ID);
+ config1 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG1);
+ convrate = i2c_smbus_read_byte_data(client, LM90_REG_R_CONVRATE);
+ if (man_id < 0 || chip_id < 0 || config1 < 0 || convrate < 0)
+ return -ENODEV;
+
+ if (man_id == 0x01 || man_id == 0x5C || man_id == 0x41) {
+ config2 = i2c_smbus_read_byte_data(client, LM90_REG_R_CONFIG2);
+ if (config2 < 0)
+ return -ENODEV;
+ } else
+ config2 = 0; /* Make compiler happy */
+
+ if ((address == 0x4C || address == 0x4D)
+ && man_id == 0x01) { /* National Semiconductor */
+ if ((config1 & 0x2A) == 0x00
+ && (config2 & 0xF8) == 0x00
+ && convrate <= 0x09) {
+ if (address == 0x4C
+ && (chip_id & 0xF0) == 0x20) { /* LM90 */
+ name = "lm90";
+ } else
+ if ((chip_id & 0xF0) == 0x30) { /* LM89/LM99 */
+ name = "lm99";
+ dev_info(&adapter->dev,
+ "Assuming LM99 chip at 0x%02x\n",
+ address);
+ dev_info(&adapter->dev,
+ "If it is an LM89, instantiate it "
+ "with the new_device sysfs "
+ "interface\n");
+ } else
+ if (address == 0x4C
+ && (chip_id & 0xF0) == 0x10) { /* LM86 */
+ name = "lm86";
+ }
+ }
+ } else
+ if ((address == 0x4C || address == 0x4D)
+ && man_id == 0x41) { /* Analog Devices */
+ if ((chip_id & 0xF0) == 0x40 /* ADM1032 */
+ && (config1 & 0x3F) == 0x00
+ && convrate <= 0x0A) {
+ name = "adm1032";
+ /*
+ * The ADM1032 supports PEC, but only if combined
+ * transactions are not used.
+ */
+ if (i2c_check_functionality(adapter,
+ I2C_FUNC_SMBUS_BYTE))
+ info->flags |= I2C_CLIENT_PEC;
+ } else
+ if (chip_id == 0x51 /* ADT7461 */
+ && (config1 & 0x1B) == 0x00
+ && convrate <= 0x0A) {
+ name = "adt7461";
+ } else
+ if (chip_id == 0x57 /* ADT7461A, NCT1008 */
+ && (config1 & 0x1B) == 0x00
+ && convrate <= 0x0A) {
+ name = "adt7461a";
+ }
+ } else
+ if (man_id == 0x4D) { /* Maxim */
+ int emerg, emerg2, status2;
+
+ /*
+ * We read MAX6659_REG_R_REMOTE_EMERG twice, and re-read
+ * LM90_REG_R_MAN_ID in between. If MAX6659_REG_R_REMOTE_EMERG
+ * exists, both readings will reflect the same value. Otherwise,
+ * the readings will be different.
+ */
+ emerg = i2c_smbus_read_byte_data(client,
+ MAX6659_REG_R_REMOTE_EMERG);
+ man_id = i2c_smbus_read_byte_data(client,
+ LM90_REG_R_MAN_ID);
+ emerg2 = i2c_smbus_read_byte_data(client,
+ MAX6659_REG_R_REMOTE_EMERG);
+ status2 = i2c_smbus_read_byte_data(client,
+ MAX6696_REG_R_STATUS2);
+ if (emerg < 0 || man_id < 0 || emerg2 < 0 || status2 < 0)
+ return -ENODEV;
+
+ /*
+ * The MAX6657, MAX6658 and MAX6659 do NOT have a chip_id
+ * register. Reading from that address will return the last
+ * read value, which in our case is those of the man_id
+ * register. Likewise, the config1 register seems to lack a
+ * low nibble, so the value will be those of the previous
+ * read, so in our case those of the man_id register.
+ * MAX6659 has a third set of upper temperature limit registers.
+ * Those registers also return values on MAX6657 and MAX6658,
+ * thus the only way to detect MAX6659 is by its address.
+ * For this reason it will be mis-detected as MAX6657 if its
+ * address is 0x4C.
+ */
+ if (chip_id == man_id
+ && (address == 0x4C || address == 0x4D || address == 0x4E)
+ && (config1 & 0x1F) == (man_id & 0x0F)
+ && convrate <= 0x09) {
+ if (address == 0x4C)
+ name = "max6657";
+ else
+ name = "max6659";
+ } else
+ /*
+ * Even though MAX6695 and MAX6696 do not have a chip ID
+ * register, reading it returns 0x01. Bit 4 of the config1
+ * register is unused and should return zero when read. Bit 0 of
+ * the status2 register is unused and should return zero when
+ * read.
+ *
+ * MAX6695 and MAX6696 have an additional set of temperature
+ * limit registers. We can detect those chips by checking if
+ * one of those registers exists.
+ */
+ if (chip_id == 0x01
+ && (config1 & 0x10) == 0x00
+ && (status2 & 0x01) == 0x00
+ && emerg == emerg2
+ && convrate <= 0x07) {
+ name = "max6696";
+ } else
+ /*
+ * The chip_id register of the MAX6680 and MAX6681 holds the
+ * revision of the chip. The lowest bit of the config1 register
+ * is unused and should return zero when read, so should the
+ * second to last bit of config1 (software reset).
+ */
+ if (chip_id == 0x01
+ && (config1 & 0x03) == 0x00
+ && convrate <= 0x07) {
+ name = "max6680";
+ } else
+ /*
+ * The chip_id register of the MAX6646/6647/6649 holds the
+ * revision of the chip. The lowest 6 bits of the config1
+ * register are unused and should return zero when read.
+ */
+ if (chip_id == 0x59
+ && (config1 & 0x3f) == 0x00
+ && convrate <= 0x07) {
+ name = "max6646";
+ }
+ } else
+ if (address == 0x4C
+ && man_id == 0x5C) { /* Winbond/Nuvoton */
+ if ((config1 & 0x2A) == 0x00
+ && (config2 & 0xF8) == 0x00) {
+ if (chip_id == 0x01 /* W83L771W/G */
+ && convrate <= 0x09) {
+ name = "w83l771";
+ } else
+ if ((chip_id & 0xFE) == 0x10 /* W83L771AWG/ASG */
+ && convrate <= 0x08) {
+ name = "w83l771";
+ }
+ }
+ } else
+ if (address >= 0x48 && address <= 0x4F
+ && man_id == 0xA1) { /* NXP Semiconductor/Philips */
+ if (chip_id == 0x00
+ && (config1 & 0x2A) == 0x00
+ && (config2 & 0xFE) == 0x00
+ && convrate <= 0x09) {
+ name = "sa56004";
+ }
+ } else
+ if ((address == 0x4C || address == 0x4D)
+ && man_id == 0x47) { /* GMT */
+ if (chip_id == 0x01 /* G781 */
+ && (config1 & 0x3F) == 0x00
+ && convrate <= 0x08)
+ name = "g781";
+ } else
+ if (address == 0x4C
+ && man_id == 0x55) { /* Texas Instruments */
+ int local_ext;
+
+ local_ext = i2c_smbus_read_byte_data(client,
+ TMP451_REG_R_LOCAL_TEMPL);
+
+ if (chip_id == 0x00 /* TMP451 */
+ && (config1 & 0x1B) == 0x00
+ && convrate <= 0x09
+ && (local_ext & 0x0F) == 0x00)
+ name = "tmp451";
+ }
+
+ if (!name) { /* identification failed */
+ dev_dbg(&adapter->dev,
+ "Unsupported chip at 0x%02x (man_id=0x%02X, "
+ "chip_id=0x%02X)\n", address, man_id, chip_id);
+ return -ENODEV;
+ }
+
+ strlcpy(info->type, name, I2C_NAME_SIZE);
+
+ return 0;
+}
+
+static void lm90_restore_conf(struct i2c_client *client, struct lm90_data *data)
+{
+ /* Restore initial configuration */
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE,
+ data->convrate_orig);
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
+ data->config_orig);
+}
+
+static void lm90_init_client(struct i2c_client *client, struct lm90_data *data)
+{
+ u8 config, convrate;
+
+ if (lm90_read_reg(client, LM90_REG_R_CONVRATE, &convrate) < 0) {
+ dev_warn(&client->dev, "Failed to read convrate register!\n");
+ convrate = LM90_DEF_CONVRATE_RVAL;
+ }
+ data->convrate_orig = convrate;
+
+ /*
+ * Start the conversions.
+ */
+ lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
+ if (lm90_read_reg(client, LM90_REG_R_CONFIG1, &config) < 0) {
+ dev_warn(&client->dev, "Initialization failed!\n");
+ return;
+ }
+ data->config_orig = config;
+
+ /* Check Temperature Range Select */
+ if (data->kind == adt7461 || data->kind == tmp451) {
+ if (config & 0x04)
+ data->flags |= LM90_FLAG_ADT7461_EXT;
+ }
+
+ /*
+ * Put MAX6680/MAX8881 into extended resolution (bit 0x10,
+ * 0.125 degree resolution) and range (0x08, extend range
+ * to -64 degree) mode for the remote temperature sensor.
+ */
+ if (data->kind == max6680)
+ config |= 0x18;
+
+ /*
+ * Select external channel 0 for max6695/96
+ */
+ if (data->kind == max6696)
+ config &= ~0x08;
+
+ config &= 0xBF; /* run */
+ if (config != data->config_orig) /* Only write if changed */
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config);
+}
+
+static bool lm90_is_tripped(struct i2c_client *client, u16 *status)
+{
+ struct lm90_data *data = i2c_get_clientdata(client);
+ u8 st, st2 = 0;
+
+ lm90_read_reg(client, LM90_REG_R_STATUS, &st);
+
+ if (data->kind == max6696)
+ lm90_read_reg(client, MAX6696_REG_R_STATUS2, &st2);
+
+ *status = st | (st2 << 8);
+
+ if ((st & 0x7f) == 0 && (st2 & 0xfe) == 0)
+ return false;
+
+ if ((st & (LM90_STATUS_LLOW | LM90_STATUS_LHIGH | LM90_STATUS_LTHRM)) ||
+ (st2 & MAX6696_STATUS2_LOT2))
+ dev_warn(&client->dev,
+ "temp%d out of range, please check!\n", 1);
+ if ((st & (LM90_STATUS_RLOW | LM90_STATUS_RHIGH | LM90_STATUS_RTHRM)) ||
+ (st2 & MAX6696_STATUS2_ROT2))
+ dev_warn(&client->dev,
+ "temp%d out of range, please check!\n", 2);
+ if (st & LM90_STATUS_ROPEN)
+ dev_warn(&client->dev,
+ "temp%d diode open, please check!\n", 2);
+ if (st2 & (MAX6696_STATUS2_R2LOW | MAX6696_STATUS2_R2HIGH |
+ MAX6696_STATUS2_R2THRM | MAX6696_STATUS2_R2OT2))
+ dev_warn(&client->dev,
+ "temp%d out of range, please check!\n", 3);
+ if (st2 & MAX6696_STATUS2_R2OPEN)
+ dev_warn(&client->dev,
+ "temp%d diode open, please check!\n", 3);
+
+ return true;
+}
+
+static irqreturn_t lm90_irq_thread(int irq, void *dev_id)
+{
+ struct i2c_client *client = dev_id;
+ u16 status;
+
+ if (lm90_is_tripped(client, &status))
+ return IRQ_HANDLED;
+ else
+ return IRQ_NONE;
+}
+
+static int lm90_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct i2c_adapter *adapter = to_i2c_adapter(dev->parent);
+ struct lm90_data *data;
+ struct regulator *regulator;
+ int groups = 0;
+ int err;
+
+ regulator = devm_regulator_get(dev, "vcc");
+ if (IS_ERR(regulator))
+ return PTR_ERR(regulator);
+
+ err = regulator_enable(regulator);
+ if (err < 0) {
+ dev_err(dev, "Failed to enable regulator: %d\n", err);
+ return err;
+ }
+
+ data = devm_kzalloc(dev, sizeof(struct lm90_data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->client = client;
+ i2c_set_clientdata(client, data);
+ mutex_init(&data->update_lock);
+
+ data->regulator = regulator;
+
+ /* Set the device type */
+ data->kind = id->driver_data;
+ if (data->kind == adm1032) {
+ if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE))
+ client->flags &= ~I2C_CLIENT_PEC;
+ }
+
+ /*
+ * Different devices have different alarm bits triggering the
+ * ALERT# output
+ */
+ data->alert_alarms = lm90_params[data->kind].alert_alarms;
+
+ /* Set chip capabilities */
+ data->flags = lm90_params[data->kind].flags;
+ data->reg_local_ext = lm90_params[data->kind].reg_local_ext;
+
+ /* Set maximum conversion rate */
+ data->max_convrate = lm90_params[data->kind].max_convrate;
+
+ /* Initialize the LM90 chip */
+ lm90_init_client(client, data);
+
+ /* Register sysfs hooks */
+ data->groups[groups++] = &lm90_group;
+
+ if (data->flags & LM90_HAVE_OFFSET)
+ data->groups[groups++] = &lm90_temp2_offset_group;
+
+ if (data->flags & LM90_HAVE_EMERGENCY)
+ data->groups[groups++] = &lm90_emergency_group;
+
+ if (data->flags & LM90_HAVE_EMERGENCY_ALARM)
+ data->groups[groups++] = &lm90_emergency_alarm_group;
+
+ if (data->flags & LM90_HAVE_TEMP3)
+ data->groups[groups++] = &lm90_temp3_group;
+
+ if (client->flags & I2C_CLIENT_PEC) {
+ err = device_create_file(dev, &dev_attr_pec);
+ if (err)
+ goto exit_restore;
+ }
+
+ data->hwmon_dev = hwmon_device_register_with_groups(dev, client->name,
+ data, data->groups);
+ if (IS_ERR(data->hwmon_dev)) {
+ err = PTR_ERR(data->hwmon_dev);
+ goto exit_remove_pec;
+ }
+
+ if (client->irq) {
+ dev_dbg(dev, "IRQ: %d\n", client->irq);
+ err = devm_request_threaded_irq(dev, client->irq,
+ NULL, lm90_irq_thread,
+ IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+ "lm90", client);
+ if (err < 0) {
+ dev_err(dev, "cannot request IRQ %d\n", client->irq);
+ goto exit_unregister;
+ }
+ }
+
+ return 0;
+
+exit_unregister:
+ hwmon_device_unregister(data->hwmon_dev);
+exit_remove_pec:
+ device_remove_file(dev, &dev_attr_pec);
+exit_restore:
+ lm90_restore_conf(client, data);
+ regulator_disable(data->regulator);
+
+ return err;
+}
+
+static int lm90_remove(struct i2c_client *client)
+{
+ struct lm90_data *data = i2c_get_clientdata(client);
+
+ hwmon_device_unregister(data->hwmon_dev);
+ device_remove_file(&client->dev, &dev_attr_pec);
+ lm90_restore_conf(client, data);
+ regulator_disable(data->regulator);
+
+ return 0;
+}
+
+static void lm90_alert(struct i2c_client *client, unsigned int flag)
+{
+ u16 alarms;
+
+ if (lm90_is_tripped(client, &alarms)) {
+ /*
+ * Disable ALERT# output, because these chips don't implement
+ * SMBus alert correctly; they should only hold the alert line
+ * low briefly.
+ */
+ struct lm90_data *data = i2c_get_clientdata(client);
+
+ if ((data->flags & LM90_HAVE_BROKEN_ALERT)
+ && (alarms & data->alert_alarms)) {
+ u8 config;
+ dev_dbg(&client->dev, "Disabling ALERT#\n");
+ lm90_read_reg(client, LM90_REG_R_CONFIG1, &config);
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
+ config | 0x80);
+ }
+ } else {
+ dev_info(&client->dev, "Everything OK\n");
+ }
+}
+
+static struct i2c_driver lm90_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "lm90",
+ },
+ .probe = lm90_probe,
+ .remove = lm90_remove,
+ .alert = lm90_alert,
+ .id_table = lm90_id,
+ .detect = lm90_detect,
+ .address_list = normal_i2c,
+};
+
+module_i2c_driver(lm90_driver);
+
+MODULE_AUTHOR("Jean Delvare <jdelvare@suse.de>");
+MODULE_DESCRIPTION("LM90/ADM1032 driver");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff