--- /dev/null
+/*
+ * (c) 2003-2006 Advanced Micro Devices, Inc.
+ * Your use of this code is subject to the terms and conditions of the
+ * GNU general public license version 2. See "COPYING" or
+ * http://www.gnu.org/licenses/gpl.html
+ */
+
+struct powernow_k8_data {
+ unsigned int cpu;
+
+ u32 numps; /* number of p-states */
+ u32 batps; /* number of p-states supported on battery */
+
+ /* these values are constant when the PSB is used to determine
+ * vid/fid pairings, but are modified during the ->target() call
+ * when ACPI is used */
+ u32 rvo; /* ramp voltage offset */
+ u32 irt; /* isochronous relief time */
+ u32 vidmvs; /* usable value calculated from mvs */
+ u32 vstable; /* voltage stabilization time, units 20 us */
+ u32 plllock; /* pll lock time, units 1 us */
+ u32 exttype; /* extended interface = 1 */
+
+ /* keep track of the current fid / vid or pstate */
+ u32 currvid;
+ u32 currfid;
+
+ /* the powernow_table includes all frequency and vid/fid pairings:
+ * fid are the lower 8 bits of the index, vid are the upper 8 bits.
+ * frequency is in kHz */
+ struct cpufreq_frequency_table *powernow_table;
+
+ /* the acpi table needs to be kept. it's only available if ACPI was
+ * used to determine valid frequency/vid/fid states */
+ struct acpi_processor_performance acpi_data;
+
+ /* we need to keep track of associated cores, but let cpufreq
+ * handle hotplug events - so just point at cpufreq pol->cpus
+ * structure */
+ struct cpumask *available_cores;
+};
+
+/* processor's cpuid instruction support */
+#define CPUID_PROCESSOR_SIGNATURE 1 /* function 1 */
+#define CPUID_XFAM 0x0ff00000 /* extended family */
+#define CPUID_XFAM_K8 0
+#define CPUID_XMOD 0x000f0000 /* extended model */
+#define CPUID_XMOD_REV_MASK 0x000c0000
+#define CPUID_XFAM_10H 0x00100000 /* family 0x10 */
+#define CPUID_USE_XFAM_XMOD 0x00000f00
+#define CPUID_GET_MAX_CAPABILITIES 0x80000000
+#define CPUID_FREQ_VOLT_CAPABILITIES 0x80000007
+#define P_STATE_TRANSITION_CAPABLE 6
+
+/* Model Specific Registers for p-state transitions. MSRs are 64-bit. For */
+/* writes (wrmsr - opcode 0f 30), the register number is placed in ecx, and */
+/* the value to write is placed in edx:eax. For reads (rdmsr - opcode 0f 32), */
+/* the register number is placed in ecx, and the data is returned in edx:eax. */
+
+#define MSR_FIDVID_CTL 0xc0010041
+#define MSR_FIDVID_STATUS 0xc0010042
+
+/* Field definitions within the FID VID Low Control MSR : */
+#define MSR_C_LO_INIT_FID_VID 0x00010000
+#define MSR_C_LO_NEW_VID 0x00003f00
+#define MSR_C_LO_NEW_FID 0x0000003f
+#define MSR_C_LO_VID_SHIFT 8
+
+/* Field definitions within the FID VID High Control MSR : */
+#define MSR_C_HI_STP_GNT_TO 0x000fffff
+
+/* Field definitions within the FID VID Low Status MSR : */
+#define MSR_S_LO_CHANGE_PENDING 0x80000000 /* cleared when completed */
+#define MSR_S_LO_MAX_RAMP_VID 0x3f000000
+#define MSR_S_LO_MAX_FID 0x003f0000
+#define MSR_S_LO_START_FID 0x00003f00
+#define MSR_S_LO_CURRENT_FID 0x0000003f
+
+/* Field definitions within the FID VID High Status MSR : */
+#define MSR_S_HI_MIN_WORKING_VID 0x3f000000
+#define MSR_S_HI_MAX_WORKING_VID 0x003f0000
+#define MSR_S_HI_START_VID 0x00003f00
+#define MSR_S_HI_CURRENT_VID 0x0000003f
+#define MSR_C_HI_STP_GNT_BENIGN 0x00000001
+
+/*
+ * There are restrictions frequencies have to follow:
+ * - only 1 entry in the low fid table ( <=1.4GHz )
+ * - lowest entry in the high fid table must be >= 2 * the entry in the
+ * low fid table
+ * - lowest entry in the high fid table must be a <= 200MHz + 2 * the entry
+ * in the low fid table
+ * - the parts can only step at <= 200 MHz intervals, odd fid values are
+ * supported in revision G and later revisions.
+ * - lowest frequency must be >= interprocessor hypertransport link speed
+ * (only applies to MP systems obviously)
+ */
+
+/* fids (frequency identifiers) are arranged in 2 tables - lo and hi */
+#define LO_FID_TABLE_TOP 7 /* fid values marking the boundary */
+#define HI_FID_TABLE_BOTTOM 8 /* between the low and high tables */
+
+#define LO_VCOFREQ_TABLE_TOP 1400 /* corresponding vco frequency values */
+#define HI_VCOFREQ_TABLE_BOTTOM 1600
+
+#define MIN_FREQ_RESOLUTION 200 /* fids jump by 2 matching freq jumps by 200 */
+
+#define MAX_FID 0x2a /* Spec only gives FID values as far as 5 GHz */
+#define LEAST_VID 0x3e /* Lowest (numerically highest) useful vid value */
+
+#define MIN_FREQ 800 /* Min and max freqs, per spec */
+#define MAX_FREQ 5000
+
+#define INVALID_FID_MASK 0xffffffc0 /* not a valid fid if these bits are set */
+#define INVALID_VID_MASK 0xffffffc0 /* not a valid vid if these bits are set */
+
+#define VID_OFF 0x3f
+
+#define STOP_GRANT_5NS 1 /* min poss memory access latency for voltage change */
+
+#define PLL_LOCK_CONVERSION (1000/5) /* ms to ns, then divide by clock period */
+
+#define MAXIMUM_VID_STEPS 1 /* Current cpus only allow a single step of 25mV */
+#define VST_UNITS_20US 20 /* Voltage Stabilization Time is in units of 20us */
+
+/*
+ * Most values of interest are encoded in a single field of the _PSS
+ * entries: the "control" value.
+ */
+
+#define IRT_SHIFT 30
+#define RVO_SHIFT 28
+#define EXT_TYPE_SHIFT 27
+#define PLL_L_SHIFT 20
+#define MVS_SHIFT 18
+#define VST_SHIFT 11
+#define VID_SHIFT 6
+#define IRT_MASK 3
+#define RVO_MASK 3
+#define EXT_TYPE_MASK 1
+#define PLL_L_MASK 0x7f
+#define MVS_MASK 3
+#define VST_MASK 0x7f
+#define VID_MASK 0x1f
+#define FID_MASK 0x1f
+#define EXT_VID_MASK 0x3f
+#define EXT_FID_MASK 0x3f
+
+
+/*
+ * Version 1.4 of the PSB table. This table is constructed by BIOS and is
+ * to tell the OS's power management driver which VIDs and FIDs are
+ * supported by this particular processor.
+ * If the data in the PSB / PST is wrong, then this driver will program the
+ * wrong values into hardware, which is very likely to lead to a crash.
+ */
+
+#define PSB_ID_STRING "AMDK7PNOW!"
+#define PSB_ID_STRING_LEN 10
+
+#define PSB_VERSION_1_4 0x14
+
+struct psb_s {
+ u8 signature[10];
+ u8 tableversion;
+ u8 flags1;
+ u16 vstable;
+ u8 flags2;
+ u8 num_tables;
+ u32 cpuid;
+ u8 plllocktime;
+ u8 maxfid;
+ u8 maxvid;
+ u8 numps;
+};
+
+/* Pairs of fid/vid values are appended to the version 1.4 PSB table. */
+struct pst_s {
+ u8 fid;
+ u8 vid;
+};
+
+static int core_voltage_pre_transition(struct powernow_k8_data *data,
+ u32 reqvid, u32 regfid);
+static int core_voltage_post_transition(struct powernow_k8_data *data, u32 reqvid);
+static int core_frequency_transition(struct powernow_k8_data *data, u32 reqfid);
+
+static void powernow_k8_acpi_pst_values(struct powernow_k8_data *data, unsigned int index);
+
+static int fill_powernow_table_fidvid(struct powernow_k8_data *data, struct cpufreq_frequency_table *powernow_table);
Code Review / kvmfornfv.git / blobdiff