--- /dev/null
+/*
+ * pata_sis.c - SiS ATA driver
+ *
+ * (C) 2005 Red Hat
+ * (C) 2007,2009 Bartlomiej Zolnierkiewicz
+ *
+ * Based upon linux/drivers/ide/pci/sis5513.c
+ * Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2002 Lionel Bouton <Lionel.Bouton@inet6.fr>, Maintainer
+ * Copyright (C) 2003 Vojtech Pavlik <vojtech@suse.cz>
+ * SiS Taiwan : for direct support and hardware.
+ * Daniela Engert : for initial ATA100 advices and numerous others.
+ * John Fremlin, Manfred Spraul, Dave Morgan, Peter Kjellerstedt :
+ * for checking code correctness, providing patches.
+ * Original tests and design on the SiS620 chipset.
+ * ATA100 tests and design on the SiS735 chipset.
+ * ATA16/33 support from specs
+ * ATA133 support for SiS961/962 by L.C. Chang <lcchang@sis.com.tw>
+ *
+ *
+ * TODO
+ * Check MWDMA on drives that don't support MWDMA speed pio cycles ?
+ * More Testing
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+#include "sis.h"
+
+#define DRV_NAME "pata_sis"
+#define DRV_VERSION "0.5.2"
+
+struct sis_chipset {
+ u16 device; /* PCI host ID */
+ const struct ata_port_info *info; /* Info block */
+ /* Probably add family, cable detect type etc here to clean
+ up code later */
+};
+
+struct sis_laptop {
+ u16 device;
+ u16 subvendor;
+ u16 subdevice;
+};
+
+static const struct sis_laptop sis_laptop[] = {
+ /* devid, subvendor, subdev */
+ { 0x5513, 0x1043, 0x1107 }, /* ASUS A6K */
+ { 0x5513, 0x1734, 0x105F }, /* FSC Amilo A1630 */
+ { 0x5513, 0x1071, 0x8640 }, /* EasyNote K5305 */
+ /* end marker */
+ { 0, }
+};
+
+static int sis_short_ata40(struct pci_dev *dev)
+{
+ const struct sis_laptop *lap = &sis_laptop[0];
+
+ while (lap->device) {
+ if (lap->device == dev->device &&
+ lap->subvendor == dev->subsystem_vendor &&
+ lap->subdevice == dev->subsystem_device)
+ return 1;
+ lap++;
+ }
+
+ return 0;
+}
+
+/**
+ * sis_old_port_base - return PCI configuration base for dev
+ * @adev: device
+ *
+ * Returns the base of the PCI configuration registers for this port
+ * number.
+ */
+
+static int sis_old_port_base(struct ata_device *adev)
+{
+ return 0x40 + (4 * adev->link->ap->port_no) + (2 * adev->devno);
+}
+
+/**
+ * sis_port_base - return PCI configuration base for dev
+ * @adev: device
+ *
+ * Returns the base of the PCI configuration registers for this port
+ * number.
+ */
+
+static int sis_port_base(struct ata_device *adev)
+{
+ struct ata_port *ap = adev->link->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port = 0x40;
+ u32 reg54;
+
+ /* If bit 30 is set then the registers are mapped at 0x70 not 0x40 */
+ pci_read_config_dword(pdev, 0x54, ®54);
+ if (reg54 & 0x40000000)
+ port = 0x70;
+
+ return port + (8 * ap->port_no) + (4 * adev->devno);
+}
+
+/**
+ * sis_133_cable_detect - check for 40/80 pin
+ * @ap: Port
+ * @deadline: deadline jiffies for the operation
+ *
+ * Perform cable detection for the later UDMA133 capable
+ * SiS chipset.
+ */
+
+static int sis_133_cable_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u16 tmp;
+
+ /* The top bit of this register is the cable detect bit */
+ pci_read_config_word(pdev, 0x50 + 2 * ap->port_no, &tmp);
+ if ((tmp & 0x8000) && !sis_short_ata40(pdev))
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
+}
+
+/**
+ * sis_66_cable_detect - check for 40/80 pin
+ * @ap: Port
+ *
+ * Perform cable detection on the UDMA66, UDMA100 and early UDMA133
+ * SiS IDE controllers.
+ */
+
+static int sis_66_cable_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+
+ /* Older chips keep cable detect in bits 4/5 of reg 0x48 */
+ pci_read_config_byte(pdev, 0x48, &tmp);
+ tmp >>= ap->port_no;
+ if ((tmp & 0x10) && !sis_short_ata40(pdev))
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
+}
+
+
+/**
+ * sis_pre_reset - probe begin
+ * @link: ATA link
+ * @deadline: deadline jiffies for the operation
+ *
+ * Set up cable type and use generic probe init
+ */
+
+static int sis_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+ static const struct pci_bits sis_enable_bits[] = {
+ { 0x4aU, 1U, 0x02UL, 0x02UL }, /* port 0 */
+ { 0x4aU, 1U, 0x04UL, 0x04UL }, /* port 1 */
+ };
+
+ struct ata_port *ap = link->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+
+ if (!pci_test_config_bits(pdev, &sis_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ /* Clear the FIFO settings. We can't enable the FIFO until
+ we know we are poking at a disk */
+ pci_write_config_byte(pdev, 0x4B, 0);
+ return ata_sff_prereset(link, deadline);
+}
+
+
+/**
+ * sis_set_fifo - Set RWP fifo bits for this device
+ * @ap: Port
+ * @adev: Device
+ *
+ * SIS chipsets implement prefetch/postwrite bits for each device
+ * on both channels. This functionality is not ATAPI compatible and
+ * must be configured according to the class of device present
+ */
+
+static void sis_set_fifo(struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 fifoctrl;
+ u8 mask = 0x11;
+
+ mask <<= (2 * ap->port_no);
+ mask <<= adev->devno;
+
+ /* This holds various bits including the FIFO control */
+ pci_read_config_byte(pdev, 0x4B, &fifoctrl);
+ fifoctrl &= ~mask;
+
+ /* Enable for ATA (disk) only */
+ if (adev->class == ATA_DEV_ATA)
+ fifoctrl |= mask;
+ pci_write_config_byte(pdev, 0x4B, fifoctrl);
+}
+
+/**
+ * sis_old_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring for.
+ *
+ * Set PIO mode for device, in host controller PCI config space. This
+ * function handles PIO set up for all chips that are pre ATA100 and
+ * also early ATA100 devices.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_old_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port = sis_old_port_base(adev);
+ u8 t1, t2;
+ int speed = adev->pio_mode - XFER_PIO_0;
+
+ static const u8 active[] = { 0x00, 0x07, 0x04, 0x03, 0x01 };
+ static const u8 recovery[] = { 0x00, 0x06, 0x04, 0x03, 0x03 };
+
+ sis_set_fifo(ap, adev);
+
+ pci_read_config_byte(pdev, port, &t1);
+ pci_read_config_byte(pdev, port + 1, &t2);
+
+ t1 &= ~0x0F; /* Clear active/recovery timings */
+ t2 &= ~0x07;
+
+ t1 |= active[speed];
+ t2 |= recovery[speed];
+
+ pci_write_config_byte(pdev, port, t1);
+ pci_write_config_byte(pdev, port + 1, t2);
+}
+
+/**
+ * sis_100_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring for.
+ *
+ * Set PIO mode for device, in host controller PCI config space. This
+ * function handles PIO set up for ATA100 devices and early ATA133.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_100_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port = sis_old_port_base(adev);
+ int speed = adev->pio_mode - XFER_PIO_0;
+
+ static const u8 actrec[] = { 0x00, 0x67, 0x44, 0x33, 0x31 };
+
+ sis_set_fifo(ap, adev);
+
+ pci_write_config_byte(pdev, port, actrec[speed]);
+}
+
+/**
+ * sis_133_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device we are configuring for.
+ *
+ * Set PIO mode for device, in host controller PCI config space. This
+ * function handles PIO set up for the later ATA133 devices.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_133_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port;
+ u32 t1;
+ int speed = adev->pio_mode - XFER_PIO_0;
+
+ static const u32 timing133[] = {
+ 0x28269000, /* Recovery << 24 | Act << 16 | Ini << 12 */
+ 0x0C266000,
+ 0x04263000,
+ 0x0C0A3000,
+ 0x05093000
+ };
+ static const u32 timing100[] = {
+ 0x1E1C6000, /* Recovery << 24 | Act << 16 | Ini << 12 */
+ 0x091C4000,
+ 0x031C2000,
+ 0x09072000,
+ 0x04062000
+ };
+
+ sis_set_fifo(ap, adev);
+
+ port = sis_port_base(adev);
+ pci_read_config_dword(pdev, port, &t1);
+ t1 &= 0xC0C00FFF; /* Mask out timing */
+
+ if (t1 & 0x08) /* 100 or 133 ? */
+ t1 |= timing133[speed];
+ else
+ t1 |= timing100[speed];
+ pci_write_config_byte(pdev, port, t1);
+}
+
+/**
+ * sis_old_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * Handles pre UDMA and UDMA33 devices. Supports MWDMA as well unlike
+ * the old ide/pci driver.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_old_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int speed = adev->dma_mode - XFER_MW_DMA_0;
+ int drive_pci = sis_old_port_base(adev);
+ u16 timing;
+
+ static const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
+ static const u16 udma_bits[] = { 0xE000, 0xC000, 0xA000 };
+
+ pci_read_config_word(pdev, drive_pci, &timing);
+
+ if (adev->dma_mode < XFER_UDMA_0) {
+ /* bits 3-0 hold recovery timing bits 8-10 active timing and
+ the higher bits are dependent on the device */
+ timing &= ~0x870F;
+ timing |= mwdma_bits[speed];
+ } else {
+ /* Bit 15 is UDMA on/off, bit 13-14 are cycle time */
+ speed = adev->dma_mode - XFER_UDMA_0;
+ timing &= ~0x6000;
+ timing |= udma_bits[speed];
+ }
+ pci_write_config_word(pdev, drive_pci, timing);
+}
+
+/**
+ * sis_66_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * Handles UDMA66 and early UDMA100 devices. Supports MWDMA as well unlike
+ * the old ide/pci driver.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_66_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int speed = adev->dma_mode - XFER_MW_DMA_0;
+ int drive_pci = sis_old_port_base(adev);
+ u16 timing;
+
+ /* MWDMA 0-2 and UDMA 0-5 */
+ static const u16 mwdma_bits[] = { 0x008, 0x302, 0x301 };
+ static const u16 udma_bits[] = { 0xF000, 0xD000, 0xB000, 0xA000, 0x9000, 0x8000 };
+
+ pci_read_config_word(pdev, drive_pci, &timing);
+
+ if (adev->dma_mode < XFER_UDMA_0) {
+ /* bits 3-0 hold recovery timing bits 8-10 active timing and
+ the higher bits are dependent on the device, bit 15 udma */
+ timing &= ~0x870F;
+ timing |= mwdma_bits[speed];
+ } else {
+ /* Bit 15 is UDMA on/off, bit 12-14 are cycle time */
+ speed = adev->dma_mode - XFER_UDMA_0;
+ timing &= ~0xF000;
+ timing |= udma_bits[speed];
+ }
+ pci_write_config_word(pdev, drive_pci, timing);
+}
+
+/**
+ * sis_100_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * Handles UDMA66 and early UDMA100 devices.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_100_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int speed = adev->dma_mode - XFER_MW_DMA_0;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+
+ static const u8 udma_bits[] = { 0x8B, 0x87, 0x85, 0x83, 0x82, 0x81};
+
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
+
+ if (adev->dma_mode < XFER_UDMA_0) {
+ /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
+ } else {
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
+ speed = adev->dma_mode - XFER_UDMA_0;
+ timing &= ~0x8F;
+ timing |= udma_bits[speed];
+ }
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
+}
+
+/**
+ * sis_133_early_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * Handles early SiS 961 bridges.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_133_early_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int speed = adev->dma_mode - XFER_MW_DMA_0;
+ int drive_pci = sis_old_port_base(adev);
+ u8 timing;
+ /* Low 4 bits are timing */
+ static const u8 udma_bits[] = { 0x8F, 0x8A, 0x87, 0x85, 0x83, 0x82, 0x81};
+
+ pci_read_config_byte(pdev, drive_pci + 1, &timing);
+
+ if (adev->dma_mode < XFER_UDMA_0) {
+ /* NOT SUPPORTED YET: NEED DATA SHEET. DITTO IN OLD DRIVER */
+ } else {
+ /* Bit 7 is UDMA on/off, bit 0-3 are cycle time */
+ speed = adev->dma_mode - XFER_UDMA_0;
+ timing &= ~0x8F;
+ timing |= udma_bits[speed];
+ }
+ pci_write_config_byte(pdev, drive_pci + 1, timing);
+}
+
+/**
+ * sis_133_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void sis_133_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port;
+ u32 t1;
+
+ port = sis_port_base(adev);
+ pci_read_config_dword(pdev, port, &t1);
+
+ if (adev->dma_mode < XFER_UDMA_0) {
+ /* Recovery << 24 | Act << 16 | Ini << 12, like PIO modes */
+ static const u32 timing_u100[] = { 0x19154000, 0x06072000, 0x04062000 };
+ static const u32 timing_u133[] = { 0x221C6000, 0x0C0A3000, 0x05093000 };
+ int speed = adev->dma_mode - XFER_MW_DMA_0;
+
+ t1 &= 0xC0C00FFF;
+ /* disable UDMA */
+ t1 &= ~0x00000004;
+ if (t1 & 0x08)
+ t1 |= timing_u133[speed];
+ else
+ t1 |= timing_u100[speed];
+ } else {
+ /* bits 4- cycle time 8 - cvs time */
+ static const u32 timing_u100[] = { 0x6B0, 0x470, 0x350, 0x140, 0x120, 0x110, 0x000 };
+ static const u32 timing_u133[] = { 0x9F0, 0x6A0, 0x470, 0x250, 0x230, 0x220, 0x210 };
+ int speed = adev->dma_mode - XFER_UDMA_0;
+
+ t1 &= ~0x00000FF0;
+ /* enable UDMA */
+ t1 |= 0x00000004;
+ if (t1 & 0x08)
+ t1 |= timing_u133[speed];
+ else
+ t1 |= timing_u100[speed];
+ }
+ pci_write_config_dword(pdev, port, t1);
+}
+
+/**
+ * sis_133_mode_filter - mode selection filter
+ * @adev: ATA device
+ *
+ * Block UDMA6 on devices that do not support it.
+ */
+
+static unsigned long sis_133_mode_filter(struct ata_device *adev, unsigned long mask)
+{
+ struct ata_port *ap = adev->link->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ int port = sis_port_base(adev);
+ u32 t1;
+
+ pci_read_config_dword(pdev, port, &t1);
+ /* if ATA133 is disabled, mask it out */
+ if (!(t1 & 0x08))
+ mask &= ~(0xC0 << ATA_SHIFT_UDMA);
+ return mask;
+}
+
+static struct scsi_host_template sis_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations sis_133_for_sata_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .set_piomode = sis_133_set_piomode,
+ .set_dmamode = sis_133_set_dmamode,
+ .cable_detect = sis_133_cable_detect,
+};
+
+static struct ata_port_operations sis_base_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .prereset = sis_pre_reset,
+};
+
+static struct ata_port_operations sis_133_ops = {
+ .inherits = &sis_base_ops,
+ .set_piomode = sis_133_set_piomode,
+ .set_dmamode = sis_133_set_dmamode,
+ .cable_detect = sis_133_cable_detect,
+ .mode_filter = sis_133_mode_filter,
+};
+
+static struct ata_port_operations sis_133_early_ops = {
+ .inherits = &sis_base_ops,
+ .set_piomode = sis_100_set_piomode,
+ .set_dmamode = sis_133_early_set_dmamode,
+ .cable_detect = sis_66_cable_detect,
+};
+
+static struct ata_port_operations sis_100_ops = {
+ .inherits = &sis_base_ops,
+ .set_piomode = sis_100_set_piomode,
+ .set_dmamode = sis_100_set_dmamode,
+ .cable_detect = sis_66_cable_detect,
+};
+
+static struct ata_port_operations sis_66_ops = {
+ .inherits = &sis_base_ops,
+ .set_piomode = sis_old_set_piomode,
+ .set_dmamode = sis_66_set_dmamode,
+ .cable_detect = sis_66_cable_detect,
+};
+
+static struct ata_port_operations sis_old_ops = {
+ .inherits = &sis_base_ops,
+ .set_piomode = sis_old_set_piomode,
+ .set_dmamode = sis_old_set_dmamode,
+ .cable_detect = ata_cable_40wire,
+};
+
+static const struct ata_port_info sis_info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ /* No UDMA */
+ .port_ops = &sis_old_ops,
+};
+static const struct ata_port_info sis_info33 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
+ .port_ops = &sis_old_ops,
+};
+static const struct ata_port_info sis_info66 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA4,
+ .port_ops = &sis_66_ops,
+};
+static const struct ata_port_info sis_info100 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &sis_100_ops,
+};
+static const struct ata_port_info sis_info100_early = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA5,
+ .port_ops = &sis_66_ops,
+};
+static const struct ata_port_info sis_info133 = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sis_133_ops,
+};
+const struct ata_port_info sis_info133_for_sata = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sis_133_for_sata_ops,
+};
+static const struct ata_port_info sis_info133_early = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ /* No MWDMA */
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &sis_133_early_ops,
+};
+
+/* Privately shared with the SiS180 SATA driver, not for use elsewhere */
+EXPORT_SYMBOL_GPL(sis_info133_for_sata);
+
+static void sis_fixup(struct pci_dev *pdev, struct sis_chipset *sis)
+{
+ u16 regw;
+ u8 reg;
+
+ if (sis->info == &sis_info133) {
+ pci_read_config_word(pdev, 0x50, ®w);
+ if (regw & 0x08)
+ pci_write_config_word(pdev, 0x50, regw & ~0x08);
+ pci_read_config_word(pdev, 0x52, ®w);
+ if (regw & 0x08)
+ pci_write_config_word(pdev, 0x52, regw & ~0x08);
+ return;
+ }
+
+ if (sis->info == &sis_info133_early || sis->info == &sis_info100) {
+ /* Fix up latency */
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
+ /* Set compatibility bit */
+ pci_read_config_byte(pdev, 0x49, ®);
+ if (!(reg & 0x01))
+ pci_write_config_byte(pdev, 0x49, reg | 0x01);
+ return;
+ }
+
+ if (sis->info == &sis_info66 || sis->info == &sis_info100_early) {
+ /* Fix up latency */
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x80);
+ /* Set compatibility bit */
+ pci_read_config_byte(pdev, 0x52, ®);
+ if (!(reg & 0x04))
+ pci_write_config_byte(pdev, 0x52, reg | 0x04);
+ return;
+ }
+
+ if (sis->info == &sis_info33) {
+ pci_read_config_byte(pdev, PCI_CLASS_PROG, ®);
+ if (( reg & 0x0F ) != 0x00)
+ pci_write_config_byte(pdev, PCI_CLASS_PROG, reg & 0xF0);
+ /* Fall through to ATA16 fixup below */
+ }
+
+ if (sis->info == &sis_info || sis->info == &sis_info33) {
+ /* force per drive recovery and active timings
+ needed on ATA_33 and below chips */
+ pci_read_config_byte(pdev, 0x52, ®);
+ if (!(reg & 0x08))
+ pci_write_config_byte(pdev, 0x52, reg|0x08);
+ return;
+ }
+
+ BUG();
+}
+
+/**
+ * sis_init_one - Register SiS ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in sis_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer. We probe for combined mode (sigh),
+ * and then hand over control to libata, for it to do the rest.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ const struct ata_port_info *ppi[] = { NULL, NULL };
+ struct pci_dev *host = NULL;
+ struct sis_chipset *chipset = NULL;
+ struct sis_chipset *sets;
+ int rc;
+
+ static struct sis_chipset sis_chipsets[] = {
+
+ { 0x0968, &sis_info133 },
+ { 0x0966, &sis_info133 },
+ { 0x0965, &sis_info133 },
+ { 0x0745, &sis_info100 },
+ { 0x0735, &sis_info100 },
+ { 0x0733, &sis_info100 },
+ { 0x0635, &sis_info100 },
+ { 0x0633, &sis_info100 },
+
+ { 0x0730, &sis_info100_early }, /* 100 with ATA 66 layout */
+ { 0x0550, &sis_info100_early }, /* 100 with ATA 66 layout */
+
+ { 0x0640, &sis_info66 },
+ { 0x0630, &sis_info66 },
+ { 0x0620, &sis_info66 },
+ { 0x0540, &sis_info66 },
+ { 0x0530, &sis_info66 },
+
+ { 0x5600, &sis_info33 },
+ { 0x5598, &sis_info33 },
+ { 0x5597, &sis_info33 },
+ { 0x5591, &sis_info33 },
+ { 0x5582, &sis_info33 },
+ { 0x5581, &sis_info33 },
+
+ { 0x5596, &sis_info },
+ { 0x5571, &sis_info },
+ { 0x5517, &sis_info },
+ { 0x5511, &sis_info },
+
+ {0}
+ };
+ static struct sis_chipset sis133_early = {
+ 0x0, &sis_info133_early
+ };
+ static struct sis_chipset sis133 = {
+ 0x0, &sis_info133
+ };
+ static struct sis_chipset sis100_early = {
+ 0x0, &sis_info100_early
+ };
+ static struct sis_chipset sis100 = {
+ 0x0, &sis_info100
+ };
+
+ ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+ rc = pcim_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ /* We have to find the bridge first */
+ for (sets = &sis_chipsets[0]; sets->device; sets++) {
+ host = pci_get_device(PCI_VENDOR_ID_SI, sets->device, NULL);
+ if (host != NULL) {
+ chipset = sets; /* Match found */
+ if (sets->device == 0x630) { /* SIS630 */
+ if (host->revision >= 0x30) /* 630 ET */
+ chipset = &sis100_early;
+ }
+ break;
+ }
+ }
+
+ /* Look for concealed bridges */
+ if (chipset == NULL) {
+ /* Second check */
+ u32 idemisc;
+ u16 trueid;
+
+ /* Disable ID masking and register remapping then
+ see what the real ID is */
+
+ pci_read_config_dword(pdev, 0x54, &idemisc);
+ pci_write_config_dword(pdev, 0x54, idemisc & 0x7fffffff);
+ pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
+ pci_write_config_dword(pdev, 0x54, idemisc);
+
+ switch(trueid) {
+ case 0x5518: /* SIS 962/963 */
+ dev_info(&pdev->dev,
+ "SiS 962/963 MuTIOL IDE UDMA133 controller\n");
+ chipset = &sis133;
+ if ((idemisc & 0x40000000) == 0) {
+ pci_write_config_dword(pdev, 0x54, idemisc | 0x40000000);
+ dev_info(&pdev->dev,
+ "Switching to 5513 register mapping\n");
+ }
+ break;
+ case 0x0180: /* SIS 965/965L */
+ chipset = &sis133;
+ break;
+ case 0x1180: /* SIS 966/966L */
+ chipset = &sis133;
+ break;
+ }
+ }
+
+ /* Further check */
+ if (chipset == NULL) {
+ struct pci_dev *lpc_bridge;
+ u16 trueid;
+ u8 prefctl;
+ u8 idecfg;
+
+ /* Try the second unmasking technique */
+ pci_read_config_byte(pdev, 0x4a, &idecfg);
+ pci_write_config_byte(pdev, 0x4a, idecfg | 0x10);
+ pci_read_config_word(pdev, PCI_DEVICE_ID, &trueid);
+ pci_write_config_byte(pdev, 0x4a, idecfg);
+
+ switch(trueid) {
+ case 0x5517:
+ lpc_bridge = pci_get_slot(pdev->bus, 0x10); /* Bus 0 Dev 2 Fn 0 */
+ if (lpc_bridge == NULL)
+ break;
+ pci_read_config_byte(pdev, 0x49, &prefctl);
+ pci_dev_put(lpc_bridge);
+
+ if (lpc_bridge->revision == 0x10 && (prefctl & 0x80)) {
+ chipset = &sis133_early;
+ break;
+ }
+ chipset = &sis100;
+ break;
+ }
+ }
+ pci_dev_put(host);
+
+ /* No chipset info, no support */
+ if (chipset == NULL)
+ return -ENODEV;
+
+ ppi[0] = chipset->info;
+
+ sis_fixup(pdev, chipset);
+
+ return ata_pci_bmdma_init_one(pdev, ppi, &sis_sht, chipset, 0);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int sis_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = pci_get_drvdata(pdev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+
+ sis_fixup(pdev, host->private_data);
+
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
+static const struct pci_device_id sis_pci_tbl[] = {
+ { PCI_VDEVICE(SI, 0x5513), }, /* SiS 5513 */
+ { PCI_VDEVICE(SI, 0x5518), }, /* SiS 5518 */
+ { PCI_VDEVICE(SI, 0x1180), }, /* SiS 1180 */
+
+ { }
+};
+
+static struct pci_driver sis_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = sis_pci_tbl,
+ .probe = sis_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+ .suspend = ata_pci_device_suspend,
+ .resume = sis_reinit_one,
+#endif
+};
+
+module_pci_driver(sis_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for SiS ATA");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sis_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
Code Review / kvmfornfv.git / blobdiff