--- /dev/null
+/*
+ * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver
+ *
+ * The IT8213 is a very Intel ICH like device for timing purposes, having
+ * a similar register layout and the same split clock arrangement. Cable
+ * detection is different, and it does not have slave channels or all the
+ * clutter of later ICH/SATA setups.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+#include <linux/ata.h>
+
+#define DRV_NAME "pata_it8213"
+#define DRV_VERSION "0.0.3"
+
+/**
+ * it8213_pre_reset - probe begin
+ * @link: link
+ * @deadline: deadline jiffies for the operation
+ *
+ * Filter out ports by the enable bits before doing the normal reset
+ * and probe.
+ */
+
+static int it8213_pre_reset(struct ata_link *link, unsigned long deadline)
+{
+ static const struct pci_bits it8213_enable_bits[] = {
+ { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */
+ };
+ struct ata_port *ap = link->ap;
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no]))
+ return -ENOENT;
+
+ return ata_sff_prereset(link, deadline);
+}
+
+/**
+ * it8213_cable_detect - check for 40/80 pin
+ * @ap: Port
+ *
+ * Perform cable detection for the 8213 ATA interface. This is
+ * different to the PIIX arrangement
+ */
+
+static int it8213_cable_detect(struct ata_port *ap)
+{
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u8 tmp;
+ pci_read_config_byte(pdev, 0x42, &tmp);
+ if (tmp & 2) /* The initial docs are incorrect */
+ return ATA_CBL_PATA40;
+ return ATA_CBL_PATA80;
+}
+
+/**
+ * it8213_set_piomode - Initialize host controller PATA PIO timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device whose timings we are configuring
+ *
+ * Set PIO mode for device, in host controller PCI config space.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
+{
+ unsigned int pio = adev->pio_mode - XFER_PIO_0;
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ unsigned int master_port = ap->port_no ? 0x42 : 0x40;
+ u16 master_data;
+ int control = 0;
+
+ /*
+ * See Intel Document 298600-004 for the timing programing rules
+ * for PIIX/ICH. The 8213 is a clone so very similar
+ */
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ if (pio > 1)
+ control |= 1; /* TIME */
+ if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */
+ control |= 2; /* IE */
+ /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
+ if (adev->class != ATA_DEV_ATA)
+ control |= 4; /* PPE */
+
+ pci_read_config_word(dev, master_port, &master_data);
+
+ /* Set PPE, IE, and TIME as appropriate */
+ if (adev->devno == 0) {
+ master_data &= 0xCCF0;
+ master_data |= control;
+ master_data |= (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ } else {
+ u8 slave_data;
+
+ master_data &= 0xFF0F;
+ master_data |= (control << 4);
+
+ /* Slave timing in separate register */
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= 0xF0;
+ slave_data |= (timings[pio][0] << 2) | timings[pio][1];
+ pci_write_config_byte(dev, 0x44, slave_data);
+ }
+
+ master_data |= 0x4000; /* Ensure SITRE is set */
+ pci_write_config_word(dev, master_port, master_data);
+}
+
+/**
+ * it8213_set_dmamode - Initialize host controller PATA DMA timings
+ * @ap: Port whose timings we are configuring
+ * @adev: Device to program
+ *
+ * Set UDMA/MWDMA mode for device, in host controller PCI config space.
+ * This device is basically an ICH alike.
+ *
+ * LOCKING:
+ * None (inherited from caller).
+ */
+
+static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
+{
+ struct pci_dev *dev = to_pci_dev(ap->host->dev);
+ u16 master_data;
+ u8 speed = adev->dma_mode;
+ int devid = adev->devno;
+ u8 udma_enable;
+
+ static const /* ISP RTC */
+ u8 timings[][2] = { { 0, 0 },
+ { 0, 0 },
+ { 1, 0 },
+ { 2, 1 },
+ { 2, 3 }, };
+
+ pci_read_config_word(dev, 0x40, &master_data);
+ pci_read_config_byte(dev, 0x48, &udma_enable);
+
+ if (speed >= XFER_UDMA_0) {
+ unsigned int udma = adev->dma_mode - XFER_UDMA_0;
+ u16 udma_timing;
+ u16 ideconf;
+ int u_clock, u_speed;
+
+ /* Clocks follow the PIIX style */
+ u_speed = min(2 - (udma & 1), udma);
+ if (udma > 4)
+ u_clock = 0x1000; /* 100Mhz */
+ else if (udma > 2)
+ u_clock = 1; /* 66Mhz */
+ else
+ u_clock = 0; /* 33Mhz */
+
+ udma_enable |= (1 << devid);
+
+ /* Load the UDMA cycle time */
+ pci_read_config_word(dev, 0x4A, &udma_timing);
+ udma_timing &= ~(3 << (4 * devid));
+ udma_timing |= u_speed << (4 * devid);
+ pci_write_config_word(dev, 0x4A, udma_timing);
+
+ /* Load the clock selection */
+ pci_read_config_word(dev, 0x54, &ideconf);
+ ideconf &= ~(0x1001 << devid);
+ ideconf |= u_clock << devid;
+ pci_write_config_word(dev, 0x54, ideconf);
+ } else {
+ /*
+ * MWDMA is driven by the PIO timings. We must also enable
+ * IORDY unconditionally along with TIME1. PPE has already
+ * been set when the PIO timing was set.
+ */
+ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0;
+ unsigned int control;
+ u8 slave_data;
+ static const unsigned int needed_pio[3] = {
+ XFER_PIO_0, XFER_PIO_3, XFER_PIO_4
+ };
+ int pio = needed_pio[mwdma] - XFER_PIO_0;
+
+ control = 3; /* IORDY|TIME1 */
+
+ /* If the drive MWDMA is faster than it can do PIO then
+ we must force PIO into PIO0 */
+
+ if (adev->pio_mode < needed_pio[mwdma])
+ /* Enable DMA timing only */
+ control |= 8; /* PIO cycles in PIO0 */
+
+ if (devid) { /* Slave */
+ master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */
+ master_data |= control << 4;
+ pci_read_config_byte(dev, 0x44, &slave_data);
+ slave_data &= 0xF0;
+ /* Load the matching timing */
+ slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
+ pci_write_config_byte(dev, 0x44, slave_data);
+ } else { /* Master */
+ master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY
+ and master timing bits */
+ master_data |= control;
+ master_data |=
+ (timings[pio][0] << 12) |
+ (timings[pio][1] << 8);
+ }
+ udma_enable &= ~(1 << devid);
+ pci_write_config_word(dev, 0x40, master_data);
+ }
+ pci_write_config_byte(dev, 0x48, udma_enable);
+}
+
+static struct scsi_host_template it8213_sht = {
+ ATA_BMDMA_SHT(DRV_NAME),
+};
+
+
+static struct ata_port_operations it8213_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .cable_detect = it8213_cable_detect,
+ .set_piomode = it8213_set_piomode,
+ .set_dmamode = it8213_set_dmamode,
+ .prereset = it8213_pre_reset,
+};
+
+
+/**
+ * it8213_init_one - Register 8213 ATA PCI device with kernel services
+ * @pdev: PCI device to register
+ * @ent: Entry in it8213_pci_tbl matching with @pdev
+ *
+ * Called from kernel PCI layer.
+ *
+ * LOCKING:
+ * Inherited from PCI layer (may sleep).
+ *
+ * RETURNS:
+ * Zero on success, or -ERRNO value.
+ */
+
+static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static const struct ata_port_info info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA12_ONLY,
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &it8213_ops,
+ };
+ /* Current IT8213 stuff is single port */
+ const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info };
+
+ ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+ return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0);
+}
+
+static const struct pci_device_id it8213_pci_tbl[] = {
+ { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), },
+
+ { } /* terminate list */
+};
+
+static struct pci_driver it8213_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = it8213_pci_tbl,
+ .probe = it8213_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+module_pci_driver(it8213_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, it8213_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
Code Review / kvmfornfv.git / blobdiff