#include "qcom-apq8064-v2.0.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
/ {
model = "Qualcomm APQ8064/IFC6410";
compatible = "qcom,apq8064-ifc6410", "qcom,apq8064";
+ aliases {
+ serial0 = &gsbi7_serial;
+ serial1 = &gsbi6_serial;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ pwrseq {
+ compatible = "simple-bus";
+
+ sdcc4_pwrseq: sdcc4_pwrseq {
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_default_gpios>;
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pm8921_gpio 43 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <¬ify_led>;
+
+ led@1 {
+ label = "apq8064:green:user1";
+ gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
soc {
pinctrl@800000 {
- i2c1_pins: i2c1 {
- mux {
- pins = "gpio20", "gpio21";
- function = "gsbi1";
- };
- };
-
card_detect: card_detect {
mux {
pins = "gpio26";
};
};
+ rpm@108000 {
+ regulators {
+ vin_lvs1_3_6-supply = <&pm8921_s4>;
+ vin_lvs2-supply = <&pm8921_s1>;
+ vin_lvs4_5_7-supply = <&pm8921_s4>;
+
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+ vdd_l24-supply = <&pm8921_s1>;
+ vdd_l25-supply = <&pm8921_s1>;
+ vdd_l26-supply = <&pm8921_s7>;
+ vdd_l27-supply = <&pm8921_s7>;
+ vdd_l28-supply = <&pm8921_s7>;
+
+
+ /* Buck SMPS */
+ pm8921_s1: s1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ qcom,switch-mode-frequency = <3200000>;
+ bias-pull-down;
+ };
+
+ pm8921_s3: s3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ qcom,switch-mode-frequency = <4800000>;
+ };
+
+ pm8921_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ pm8921_s7: s7 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ pm8921_l3: l3 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ bias-pull-down;
+ };
+
+ pm8921_l4: l4 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ bias-pull-down;
+ };
+
+ pm8921_l5: l5 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <3000000>;
+ bias-pull-down;
+ };
+
+ pm8921_l6: l6 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ bias-pull-down;
+ };
+
+ pm8921_l23: l23 {
+ regulator-min-microvolt = <1700000>;
+ regulator-max-microvolt = <1900000>;
+ bias-pull-down;
+ };
+
+ pm8921_lvs1: lvs1 {
+ bias-pull-down;
+ };
+ };
+ };
+
+ ext_3p3v: regulator-fixed@1 {
+ compatible = "regulator-fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "ext_3p3v";
+ regulator-type = "voltage";
+ startup-delay-us = <0>;
+ gpio = <&tlmm_pinmux 77 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+ };
+
+ gsbi3: gsbi@16200000 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C>;
+ i2c3: i2c@16280000 {
+ status = "okay";
+ };
+ };
+
gsbi@12440000 {
status = "okay";
qcom,mode = <GSBI_PROT_I2C>;
i2c@12460000 {
status = "okay";
clock-frequency = <200000>;
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
- eeprom: eeprom@52 {
+ eeprom@52 {
compatible = "atmel,24c128";
reg = <0x52>;
pagesize = <32>;
};
};
+ gsbi@16500000 {
+ status = "ok";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+
+ serial@16540000 {
+ status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi6_uart_4pins>;
+ };
+ };
+
gsbi@16600000 {
status = "ok";
qcom,mode = <GSBI_PROT_I2C_UART>;
serial@16640000 {
status = "ok";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsbi7_uart_2pins>;
+ };
+ };
+
+ sata_phy0: phy@1b400000 {
+ status = "okay";
+ };
+
+ sata0: sata@29000000 {
+ status = "okay";
+ target-supply = <&pm8921_s4>;
+ };
+
+ /* OTG */
+ usb1_phy: phy@12500000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l4>;
+ };
+
+ usb3_phy: phy@12520000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ usb4_phy: phy@12530000 {
+ status = "okay";
+ vddcx-supply = <&pm8921_s3>;
+ v3p3-supply = <&pm8921_l3>;
+ v1p8-supply = <&pm8921_l23>;
+ };
+
+ gadget1: gadget@12500000 {
+ status = "okay";
+ };
+
+ /* OTG */
+ usb1: usb@12500000 {
+ status = "okay";
+ };
+
+ usb3: usb@12520000 {
+ status = "okay";
+ };
+
+ usb4: usb@12530000 {
+ status = "okay";
+ };
+
+ qcom,ssbi@500000 {
+ pmic@0 {
+ gpio@150 {
+ wlan_default_gpios: wlan-gpios {
+ pios {
+ pins = "gpio43";
+ function = "normal";
+ bias-disable;
+ power-source = <PM8921_GPIO_S4>;
+ };
+ };
+
+ notify_led: nled {
+ pios {
+ pins = "gpio18";
+ function = "normal";
+ bias-disable;
+ power-source = <PM8921_GPIO_S4>;
+ };
+ };
+ };
};
};
/* eMMC */
sdcc1: sdcc@12400000 {
status = "okay";
+ vmmc-supply = <&pm8921_l5>;
+ vqmmc-supply = <&pm8921_s4>;
};
/* External micro SD card */
sdcc3: sdcc@12180000 {
status = "okay";
+ vmmc-supply = <&pm8921_l6>;
pinctrl-names = "default";
pinctrl-0 = <&card_detect>;
cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
/* WLAN */
sdcc4: sdcc@121c0000 {
status = "okay";
+ vmmc-supply = <&ext_3p3v>;
+ vqmmc-supply = <&pm8921_lvs1>;
+ mmc-pwrseq = <&sdcc4_pwrseq>;
};
};
};
Code Review / kvmfornfv.git / blobdiff