/************************************************************************** ETHERBOOT - BOOTP/TFTP Bootstrap Program Author: Martin Renters Date: May/94 This code is based heavily on David Greenman's if_ed.c driver Copyright (C) 1993-1994, David Greenman, Martin Renters. This software may be used, modified, copied, distributed, and sold, in both source and binary form provided that the above copyright and these terms are retained. Under no circumstances are the authors responsible for the proper functioning of this software, nor do the authors assume any responsibility for damages incurred with its use. Multicast support added by Timothy Legge (timlegge@users.sourceforge.net) 09/28/2003 Relocation support added by Ken Yap (ken_yap@users.sourceforge.net) 28/12/02 3c503 support added by Bill Paul (wpaul@ctr.columbia.edu) on 11/15/94 SMC8416 support added by Bill Paul (wpaul@ctr.columbia.edu) on 12/25/94 3c503 PIO support added by Jim Hague (jim.hague@acm.org) on 2/17/98 RX overrun by Klaus Espenlaub (espenlaub@informatik.uni-ulm.de) on 3/10/99 parts taken from the Linux 8390 driver (by Donald Becker and Paul Gortmaker) SMC8416 PIO support added by Andrew Bettison (andrewb@zip.com.au) on 4/3/02 based on the Linux 8390 driver (by Donald Becker and Paul Gortmaker) **************************************************************************/ FILE_LICENCE ( BSD2 ); /* #warning "ns8390.c: FIXME: split ISA and PCI, clean up" */ #if 1 #if !defined(INCLUDE_NS8390) && !defined(INCLUDE_WD) && \ !defined(INCLUDE_NE) && !defined(INCLUDE_3C503) /* The driver named ns8390 is the PCI driver, often called "PCI ne2000 clones". */ # define INCLUDE_NS8390 1 #endif #include "etherboot.h" #include "nic.h" #include "ns8390.h" #include #ifdef INCLUDE_NS8390 #include #else #include #endif static unsigned char eth_vendor, eth_flags; #ifdef INCLUDE_WD static unsigned char eth_laar; #endif static unsigned short eth_nic_base, eth_asic_base; static unsigned char eth_memsize, eth_rx_start, eth_tx_start; static Address eth_bmem, eth_rmem; static unsigned char eth_drain_receiver; #ifdef INCLUDE_WD static struct wd_board { const char *name; char id; char flags; char memsize; } wd_boards[] = { {"WD8003S", TYPE_WD8003S, 0, MEM_8192}, {"WD8003E", TYPE_WD8003E, 0, MEM_8192}, {"WD8013EBT", TYPE_WD8013EBT, FLAG_16BIT, MEM_16384}, {"WD8003W", TYPE_WD8003W, 0, MEM_8192}, {"WD8003EB", TYPE_WD8003EB, 0, MEM_8192}, {"WD8013W", TYPE_WD8013W, FLAG_16BIT, MEM_16384}, {"WD8003EP/WD8013EP", TYPE_WD8013EP, 0, MEM_8192}, {"WD8013WC", TYPE_WD8013WC, FLAG_16BIT, MEM_16384}, {"WD8013EPC", TYPE_WD8013EPC, FLAG_16BIT, MEM_16384}, {"SMC8216T", TYPE_SMC8216T, FLAG_16BIT | FLAG_790, MEM_16384}, {"SMC8216C", TYPE_SMC8216C, FLAG_16BIT | FLAG_790, MEM_16384}, {"SMC8416T", TYPE_SMC8416T, FLAG_16BIT | FLAG_790, MEM_8192}, {"SMC8416C/BT", TYPE_SMC8416C, FLAG_16BIT | FLAG_790, MEM_8192}, {"SMC8013EBP", TYPE_SMC8013EBP,FLAG_16BIT, MEM_16384}, {NULL, 0, 0, 0} }; #endif #ifdef INCLUDE_3C503 static unsigned char t503_output; /* AUI or internal xcvr (Thinnet) */ #endif #if defined(INCLUDE_WD) #define ASIC_PIO WD_IAR #define eth_probe wd_probe #if defined(INCLUDE_3C503) || defined(INCLUDE_NE) || defined(INCLUDE_NS8390) Error you must only define one of INCLUDE_WD, INCLUDE_3C503, INCLUDE_NE, INCLUDE_NS8390 #endif #endif #if defined(INCLUDE_3C503) #define eth_probe t503_probe #if defined(INCLUDE_NE) || defined(INCLUDE_NS8390) || defined(INCLUDE_WD) Error you must only define one of INCLUDE_WD, INCLUDE_3C503, INCLUDE_NE, INCLUDE_NS8390 #endif #endif #if defined(INCLUDE_NE) #define eth_probe ne_probe #if defined(INCLUDE_NS8390) || defined(INCLUDE_3C503) || defined(INCLUDE_WD) Error you must only define one of INCLUDE_WD, INCLUDE_3C503, INCLUDE_NE, INCLUDE_NS8390 #endif #endif #if defined(INCLUDE_NS8390) #define eth_probe nepci_probe #if defined(INCLUDE_NE) || defined(INCLUDE_3C503) || defined(INCLUDE_WD) Error you must only define one of INCLUDE_WD, INCLUDE_3C503, INCLUDE_NE, INCLUDE_NS8390 #endif #endif #if defined(INCLUDE_3C503) #define ASIC_PIO _3COM_RFMSB #else #if defined(INCLUDE_NE) || defined(INCLUDE_NS8390) #define ASIC_PIO NE_DATA #endif #endif #if defined(INCLUDE_NE) || defined(INCLUDE_NS8390) || (defined(INCLUDE_3C503) && !defined(T503_SHMEM)) || (defined(INCLUDE_WD) && defined(WD_790_PIO)) /************************************************************************** ETH_PIO_READ - Read a frame via Programmed I/O **************************************************************************/ static void eth_pio_read(unsigned int src, unsigned char *dst, unsigned int cnt) { #ifdef INCLUDE_WD outb(src & 0xff, eth_asic_base + WD_GP2); outb(src >> 8, eth_asic_base + WD_GP2); #else outb(D8390_COMMAND_RD2 | D8390_COMMAND_STA, eth_nic_base + D8390_P0_COMMAND); outb(cnt, eth_nic_base + D8390_P0_RBCR0); outb(cnt>>8, eth_nic_base + D8390_P0_RBCR1); outb(src, eth_nic_base + D8390_P0_RSAR0); outb(src>>8, eth_nic_base + D8390_P0_RSAR1); outb(D8390_COMMAND_RD0 | D8390_COMMAND_STA, eth_nic_base + D8390_P0_COMMAND); #ifdef INCLUDE_3C503 outb(src & 0xff, eth_asic_base + _3COM_DALSB); outb(src >> 8, eth_asic_base + _3COM_DAMSB); outb(t503_output | _3COM_CR_START, eth_asic_base + _3COM_CR); #endif #endif if (eth_flags & FLAG_16BIT) cnt = (cnt + 1) >> 1; while(cnt--) { #ifdef INCLUDE_3C503 while((inb(eth_asic_base + _3COM_STREG) & _3COM_STREG_DPRDY) == 0) ; #endif if (eth_flags & FLAG_16BIT) { *((unsigned short *)dst) = inw(eth_asic_base + ASIC_PIO); dst += 2; } else *(dst++) = inb(eth_asic_base + ASIC_PIO); } #ifdef INCLUDE_3C503 outb(t503_output, eth_asic_base + _3COM_CR); #endif } /************************************************************************** ETH_PIO_WRITE - Write a frame via Programmed I/O **************************************************************************/ static void eth_pio_write(const unsigned char *src, unsigned int dst, unsigned int cnt) { #ifdef COMPEX_RL2000_FIX unsigned int x; #endif /* COMPEX_RL2000_FIX */ #ifdef INCLUDE_WD outb(dst & 0xff, eth_asic_base + WD_GP2); outb(dst >> 8, eth_asic_base + WD_GP2); #else outb(D8390_COMMAND_RD2 | D8390_COMMAND_STA, eth_nic_base + D8390_P0_COMMAND); outb(D8390_ISR_RDC, eth_nic_base + D8390_P0_ISR); outb(cnt, eth_nic_base + D8390_P0_RBCR0); outb(cnt>>8, eth_nic_base + D8390_P0_RBCR1); outb(dst, eth_nic_base + D8390_P0_RSAR0); outb(dst>>8, eth_nic_base + D8390_P0_RSAR1); outb(D8390_COMMAND_RD1 | D8390_COMMAND_STA, eth_nic_base + D8390_P0_COMMAND); #ifdef INCLUDE_3C503 outb(dst & 0xff, eth_asic_base + _3COM_DALSB); outb(dst >> 8, eth_asic_base + _3COM_DAMSB); outb(t503_output | _3COM_CR_DDIR | _3COM_CR_START, eth_asic_base + _3COM_CR); #endif #endif if (eth_flags & FLAG_16BIT) cnt = (cnt + 1) >> 1; while(cnt--) { #ifdef INCLUDE_3C503 while((inb(eth_asic_base + _3COM_STREG) & _3COM_STREG_DPRDY) == 0) ; #endif if (eth_flags & FLAG_16BIT) { outw(*((unsigned short *)src), eth_asic_base + ASIC_PIO); src += 2; } else outb(*(src++), eth_asic_base + ASIC_PIO); } #ifdef INCLUDE_3C503 outb(t503_output, eth_asic_base + _3COM_CR); #else #ifdef COMPEX_RL2000_FIX for (x = 0; x < COMPEX_RL2000_TRIES && (inb(eth_nic_base + D8390_P0_ISR) & D8390_ISR_RDC) != D8390_ISR_RDC; ++x); if (x >= COMPEX_RL2000_TRIES) printf("Warning: Compex RL2000 aborted wait!\n"); #endif /* COMPEX_RL2000_FIX */ #ifndef INCLUDE_WD while((inb(eth_nic_base + D8390_P0_ISR) & D8390_ISR_RDC) != D8390_ISR_RDC); #endif #endif } #else /************************************************************************** ETH_PIO_READ - Dummy routine when NE2000 not compiled in **************************************************************************/ static void eth_pio_read(unsigned int src __unused, unsigned char *dst __unused, unsigned int cnt __unused) {} #endif /************************************************************************** enable_multycast - Enable Multicast **************************************************************************/ static void enable_multicast(unsigned short eth_nic_base) { unsigned char mcfilter[8]; int i; memset(mcfilter, 0xFF, 8); outb(4, eth_nic_base+D8390_P0_RCR); outb(D8390_COMMAND_RD2 + D8390_COMMAND_PS1, eth_nic_base + D8390_P0_COMMAND); for(i=0;i<8;i++) { outb(mcfilter[i], eth_nic_base + 8 + i); if(inb(eth_nic_base + 8 + i)!=mcfilter[i]) printf("Error SMC 83C690 Multicast filter read/write mishap %d\n",i); } outb(D8390_COMMAND_RD2 + D8390_COMMAND_PS0, eth_nic_base + D8390_P0_COMMAND); outb(4 | 0x08, eth_nic_base+D8390_P0_RCR); } /************************************************************************** NS8390_RESET - Reset adapter **************************************************************************/ static void ns8390_reset(struct nic *nic) { int i; eth_drain_receiver = 0; #ifdef INCLUDE_WD if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS0 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS0 | D8390_COMMAND_RD2 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); if (eth_flags & FLAG_16BIT) outb(0x49, eth_nic_base+D8390_P0_DCR); else outb(0x48, eth_nic_base+D8390_P0_DCR); outb(0, eth_nic_base+D8390_P0_RBCR0); outb(0, eth_nic_base+D8390_P0_RBCR1); outb(0x20, eth_nic_base+D8390_P0_RCR); /* monitor mode */ outb(2, eth_nic_base+D8390_P0_TCR); outb(eth_tx_start, eth_nic_base+D8390_P0_TPSR); outb(eth_rx_start, eth_nic_base+D8390_P0_PSTART); #ifdef INCLUDE_WD if (eth_flags & FLAG_790) { #ifdef WD_790_PIO outb(0x10, eth_asic_base + 0x06); /* disable interrupts, enable PIO */ outb(0x01, eth_nic_base + 0x09); /* enable ring read auto-wrap */ #else outb(0, eth_nic_base + 0x09); #endif } #endif outb(eth_memsize, eth_nic_base+D8390_P0_PSTOP); outb(eth_memsize - 1, eth_nic_base+D8390_P0_BOUND); outb(0xFF, eth_nic_base+D8390_P0_ISR); outb(0, eth_nic_base+D8390_P0_IMR); #ifdef INCLUDE_WD if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS1 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS1 | D8390_COMMAND_RD2 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); for (i=0; inode_addr[i], eth_nic_base+D8390_P1_PAR0+i); for (i=0; iflags) ? 0 : _3COM_CR_XSEL; outb(t503_output, eth_asic_base + _3COM_CR); #endif } static int ns8390_poll(struct nic *nic, int retrieve); #ifndef INCLUDE_3C503 /************************************************************************** ETH_RX_OVERRUN - Bring adapter back to work after an RX overrun **************************************************************************/ static void eth_rx_overrun(struct nic *nic) { int start_time; #ifdef INCLUDE_WD if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS0 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS0 | D8390_COMMAND_RD2 | D8390_COMMAND_STP, eth_nic_base+D8390_P0_COMMAND); /* wait for at least 1.6ms - we wait one timer tick */ start_time = currticks(); while (currticks() - start_time <= 1) /* Nothing */; outb(0, eth_nic_base+D8390_P0_RBCR0); /* reset byte counter */ outb(0, eth_nic_base+D8390_P0_RBCR1); /* * Linux driver checks for interrupted TX here. This is not necessary, * because the transmit routine waits until the frame is sent. */ /* enter loopback mode and restart NIC */ outb(2, eth_nic_base+D8390_P0_TCR); #ifdef INCLUDE_WD if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS0 | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS0 | D8390_COMMAND_RD2 | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); /* clear the RX ring, acknowledge overrun interrupt */ eth_drain_receiver = 1; while (ns8390_poll(nic, 1)) /* Nothing */; eth_drain_receiver = 0; outb(D8390_ISR_OVW, eth_nic_base+D8390_P0_ISR); /* leave loopback mode - no packets to be resent (see Linux driver) */ outb(0, eth_nic_base+D8390_P0_TCR); } #endif /* INCLUDE_3C503 */ /************************************************************************** NS8390_TRANSMIT - Transmit a frame **************************************************************************/ static void ns8390_transmit( struct nic *nic, const char *d, /* Destination */ unsigned int t, /* Type */ unsigned int s, /* size */ const char *p) /* Packet */ { #if defined(INCLUDE_3C503) || (defined(INCLUDE_WD) && ! defined(WD_790_PIO)) Address eth_vmem = bus_to_virt(eth_bmem); #endif #ifdef INCLUDE_3C503 if (!(eth_flags & FLAG_PIO)) { memcpy((char *)eth_vmem, d, ETH_ALEN); /* dst */ memcpy((char *)eth_vmem+ETH_ALEN, nic->node_addr, ETH_ALEN); /* src */ *((char *)eth_vmem+12) = t>>8; /* type */ *((char *)eth_vmem+13) = t; memcpy((char *)eth_vmem+ETH_HLEN, p, s); s += ETH_HLEN; while (s < ETH_ZLEN) *((char *)eth_vmem+(s++)) = 0; } #endif #ifdef INCLUDE_WD if (eth_flags & FLAG_16BIT) { outb(eth_laar | WD_LAAR_M16EN, eth_asic_base + WD_LAAR); inb(0x84); } #ifndef WD_790_PIO /* Memory interface */ if (eth_flags & FLAG_790) { outb(WD_MSR_MENB, eth_asic_base + WD_MSR); inb(0x84); } inb(0x84); memcpy((char *)eth_vmem, d, ETH_ALEN); /* dst */ memcpy((char *)eth_vmem+ETH_ALEN, nic->node_addr, ETH_ALEN); /* src */ *((char *)eth_vmem+12) = t>>8; /* type */ *((char *)eth_vmem+13) = t; memcpy((char *)eth_vmem+ETH_HLEN, p, s); s += ETH_HLEN; while (s < ETH_ZLEN) *((char *)eth_vmem+(s++)) = 0; if (eth_flags & FLAG_790) { outb(0, eth_asic_base + WD_MSR); inb(0x84); } #else inb(0x84); #endif #endif #if defined(INCLUDE_3C503) if (eth_flags & FLAG_PIO) #endif #if defined(INCLUDE_NE) || defined(INCLUDE_NS8390) || (defined(INCLUDE_3C503) && !defined(T503_SHMEM)) || (defined(INCLUDE_WD) && defined(WD_790_PIO)) { /* Programmed I/O */ unsigned short type; type = (t >> 8) | (t << 8); eth_pio_write( (unsigned char *) d, eth_tx_start<<8, ETH_ALEN); eth_pio_write(nic->node_addr, (eth_tx_start<<8)+ETH_ALEN, ETH_ALEN); /* bcc generates worse code without (const+const) below */ eth_pio_write((unsigned char *)&type, (eth_tx_start<<8)+(ETH_ALEN+ETH_ALEN), 2); eth_pio_write( (unsigned char *) p, (eth_tx_start<<8)+ETH_HLEN, s); s += ETH_HLEN; if (s < ETH_ZLEN) s = ETH_ZLEN; } #endif #if defined(INCLUDE_3C503) #endif #ifdef INCLUDE_WD if (eth_flags & FLAG_16BIT) { outb(eth_laar & ~WD_LAAR_M16EN, eth_asic_base + WD_LAAR); inb(0x84); } if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS0 | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS0 | D8390_COMMAND_RD2 | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); outb(eth_tx_start, eth_nic_base+D8390_P0_TPSR); outb(s, eth_nic_base+D8390_P0_TBCR0); outb(s>>8, eth_nic_base+D8390_P0_TBCR1); #ifdef INCLUDE_WD if (eth_flags & FLAG_790) outb(D8390_COMMAND_PS0 | D8390_COMMAND_TXP | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); else #endif outb(D8390_COMMAND_PS0 | D8390_COMMAND_TXP | D8390_COMMAND_RD2 | D8390_COMMAND_STA, eth_nic_base+D8390_P0_COMMAND); } /************************************************************************** NS8390_POLL - Wait for a frame **************************************************************************/ static int ns8390_poll(struct nic *nic, int retrieve) { int ret = 0; unsigned char rstat, curr, next; unsigned short len, frag; unsigned short pktoff; unsigned char *p; struct ringbuffer pkthdr; #ifndef INCLUDE_3C503 /* avoid infinite recursion: see eth_rx_overrun() */ if (!eth_drain_receiver && (inb(eth_nic_base+D8390_P0_ISR) & D8390_ISR_OVW)) { eth_rx_overrun(nic); return(0); } #endif /* INCLUDE_3C503 */ rstat = inb(eth_nic_base+D8390_P0_RSR); if (!(rstat & D8390_RSTAT_PRX)) return(0); next = inb(eth_nic_base+D8390_P0_BOUND)+1; if (next >= eth_memsize) next = eth_rx_start; outb(D8390_COMMAND_PS1, eth_nic_base+D8390_P0_COMMAND); curr = inb(eth_nic_base+D8390_P1_CURR); outb(D8390_COMMAND_PS0, eth_nic_base+D8390_P0_COMMAND); if (curr >= eth_memsize) curr=eth_rx_start; if (curr == next) return(0); if ( ! retrieve ) return 1; #ifdef INCLUDE_WD if (eth_flags & FLAG_16BIT) { outb(eth_laar | WD_LAAR_M16EN, eth_asic_base + WD_LAAR); inb(0x84); } #ifndef WD_790_PIO if (eth_flags & FLAG_790) { outb(WD_MSR_MENB, eth_asic_base + WD_MSR); inb(0x84); } #endif inb(0x84); #endif pktoff = next << 8; if (eth_flags & FLAG_PIO) eth_pio_read(pktoff, (unsigned char *)&pkthdr, 4); else memcpy(&pkthdr, bus_to_virt(eth_rmem + pktoff), 4); pktoff += sizeof(pkthdr); /* incoming length includes FCS so must sub 4 */ len = pkthdr.len - 4; if ((pkthdr.status & D8390_RSTAT_PRX) == 0 || len < ETH_ZLEN || len > ETH_FRAME_LEN) { printf("Bogus packet, ignoring\n"); return (0); } else { p = nic->packet; nic->packetlen = len; /* available to caller */ frag = (eth_memsize << 8) - pktoff; if (len > frag) { /* We have a wrap-around */ /* read first part */ if (eth_flags & FLAG_PIO) eth_pio_read(pktoff, p, frag); else memcpy(p, bus_to_virt(eth_rmem + pktoff), frag); pktoff = eth_rx_start << 8; p += frag; len -= frag; } /* read second part */ if (eth_flags & FLAG_PIO) eth_pio_read(pktoff, p, len); else memcpy(p, bus_to_virt(eth_rmem + pktoff), len); ret = 1; } #ifdef INCLUDE_WD #ifndef WD_790_PIO if (eth_flags & FLAG_790) { outb(0, eth_asic_base + WD_MSR); inb(0x84); } #endif if (eth_flags & FLAG_16BIT) { outb(eth_laar & ~WD_LAAR_M16EN, eth_asic_base + WD_LAAR); inb(0x84); } inb(0x84); #endif next = pkthdr.next; /* frame number of next packet */ if (next == eth_rx_start) next = eth_memsize; outb(next-1, eth_nic_base+D8390_P0_BOUND); return(ret); } /************************************************************************** NS8390_DISABLE - Turn off adapter **************************************************************************/ static void ns8390_disable ( struct nic *nic ) { ns8390_reset(nic); } /************************************************************************** NS8390_IRQ - Enable, Disable, or Force interrupts **************************************************************************/ static void ns8390_irq(struct nic *nic __unused, irq_action_t action __unused) { switch ( action ) { case DISABLE : break; case ENABLE : break; case FORCE : break; } } static struct nic_operations ns8390_operations; static struct nic_operations ns8390_operations = { .connect = dummy_connect, .poll = ns8390_poll, .transmit = ns8390_transmit, .irq = ns8390_irq, }; /************************************************************************** ETH_PROBE - Look for an adapter **************************************************************************/ #ifdef INCLUDE_NS8390 static int eth_probe (struct nic *nic, struct pci_device *pci) #else static int eth_probe (struct dev *dev, unsigned short *probe_addrs __unused) #endif { int i; #ifdef INCLUDE_NS8390 unsigned short pci_probe_addrs[] = { pci->ioaddr, 0 }; unsigned short *probe_addrs = pci_probe_addrs; #endif eth_vendor = VENDOR_NONE; eth_drain_receiver = 0; nic->irqno = 0; #ifdef INCLUDE_WD { /****************************************************************** Search for WD/SMC cards ******************************************************************/ struct wd_board *brd; unsigned short chksum; unsigned char c; for (eth_asic_base = WD_LOW_BASE; eth_asic_base <= WD_HIGH_BASE; eth_asic_base += 0x20) { chksum = 0; for (i=8; i<16; i++) chksum += inb(eth_asic_base+i); /* Extra checks to avoid soundcard */ if ((chksum & 0xFF) == 0xFF && inb(eth_asic_base+8) != 0xFF && inb(eth_asic_base+9) != 0xFF) break; } if (eth_asic_base > WD_HIGH_BASE) return (0); /* We've found a board */ eth_vendor = VENDOR_WD; eth_nic_base = eth_asic_base + WD_NIC_ADDR; nic->ioaddr = eth_nic_base; c = inb(eth_asic_base+WD_BID); /* Get board id */ for (brd = wd_boards; brd->name; brd++) if (brd->id == c) break; if (!brd->name) { printf("Unknown WD/SMC NIC type %hhX\n", c); return (0); /* Unknown type */ } eth_flags = brd->flags; eth_memsize = brd->memsize; eth_tx_start = 0; eth_rx_start = D8390_TXBUF_SIZE; if ((c == TYPE_WD8013EP) && (inb(eth_asic_base + WD_ICR) & WD_ICR_16BIT)) { eth_flags = FLAG_16BIT; eth_memsize = MEM_16384; } if ((c & WD_SOFTCONFIG) && (!(eth_flags & FLAG_790))) { eth_bmem = (0x80000 | ((inb(eth_asic_base + WD_MSR) & 0x3F) << 13)); } else eth_bmem = WD_DEFAULT_MEM; if (brd->id == TYPE_SMC8216T || brd->id == TYPE_SMC8216C) { /* from Linux driver, 8416BT detects as 8216 sometimes */ unsigned int addr = inb(eth_asic_base + 0xb); if (((addr >> 4) & 3) == 0) { brd += 2; eth_memsize = brd->memsize; } } outb(0x80, eth_asic_base + WD_MSR); /* Reset */ for (i=0; inode_addr[i] = inb(i+eth_asic_base+WD_LAR); } DBG ( "\n%s base %4.4x", brd->name, eth_asic_base ); if (eth_flags & FLAG_790) { #ifdef WD_790_PIO DBG ( ", PIO mode, addr %s\n", eth_ntoa ( nic->node_addr ) ); eth_bmem = 0; eth_flags |= FLAG_PIO; /* force PIO mode */ outb(0, eth_asic_base+WD_MSR); #else DBG ( ", Memory %x, MAC Addr %s\n", eth_bmem, eth_ntoa ( nic->node_addr) ); outb(WD_MSR_MENB, eth_asic_base+WD_MSR); outb((inb(eth_asic_base+0x04) | 0x80), eth_asic_base+0x04); outb(((unsigned)(eth_bmem >> 13) & 0x0F) | ((unsigned)(eth_bmem >> 11) & 0x40) | (inb(eth_asic_base+0x0B) & 0xB0), eth_asic_base+0x0B); outb((inb(eth_asic_base+0x04) & ~0x80), eth_asic_base+0x04); #endif } else { DBG (", Memory %x, MAC Addr %s\n", eth_bmem, eth_ntoa ( nic->node_addr) ); outb(((unsigned)(eth_bmem >> 13) & 0x3F) | 0x40, eth_asic_base+WD_MSR); } if (eth_flags & FLAG_16BIT) { if (eth_flags & FLAG_790) { eth_laar = inb(eth_asic_base + WD_LAAR); outb(WD_LAAR_M16EN, eth_asic_base + WD_LAAR); } else { outb((eth_laar = WD_LAAR_L16EN | 1), eth_asic_base + WD_LAAR); /* The previous line used to be WD_LAAR_M16EN | WD_LAAR_L16EN | 1)); jluke@deakin.edu.au reported that removing WD_LAAR_M16EN made it work for WD8013s. This seems to work for my 8013 boards. I don't know what is really happening. I wish I had data sheets or more time to decode the Linux driver. - Ken */ } inb(0x84); } } #endif #ifdef INCLUDE_3C503 #ifdef T503_AUI nic->flags = 1; /* aui */ #else nic->flags = 0; /* no aui */ #endif /****************************************************************** Search for 3Com 3c503 if no WD/SMC cards ******************************************************************/ if (eth_vendor == VENDOR_NONE) { int idx; int iobase_reg, membase_reg; static unsigned short base[] = { 0x300, 0x310, 0x330, 0x350, 0x250, 0x280, 0x2A0, 0x2E0, 0 }; /* Loop through possible addresses checking each one */ for (idx = 0; (eth_nic_base = base[idx]) != 0; ++idx) { eth_asic_base = eth_nic_base + _3COM_ASIC_OFFSET; /* * Note that we use the same settings for both 8 and 16 bit cards: * both have an 8K bank of memory at page 1 while only the 16 bit * cards have a bank at page 0. */ eth_memsize = MEM_16384; eth_tx_start = 32; eth_rx_start = 32 + D8390_TXBUF_SIZE; /* Check our base address. iobase and membase should */ /* both have a maximum of 1 bit set or be 0. */ iobase_reg = inb(eth_asic_base + _3COM_BCFR); membase_reg = inb(eth_asic_base + _3COM_PCFR); if ((iobase_reg & (iobase_reg - 1)) || (membase_reg & (membase_reg - 1))) continue; /* nope */ /* Now get the shared memory address */ eth_flags = 0; switch (membase_reg) { case _3COM_PCFR_DC000: eth_bmem = 0xdc000; break; case _3COM_PCFR_D8000: eth_bmem = 0xd8000; break; case _3COM_PCFR_CC000: eth_bmem = 0xcc000; break; case _3COM_PCFR_C8000: eth_bmem = 0xc8000; break; case _3COM_PCFR_PIO: eth_flags |= FLAG_PIO; eth_bmem = 0; break; default: continue; /* nope */ } break; } if (base[idx] == 0) /* not found */ return (0); #ifndef T503_SHMEM eth_flags |= FLAG_PIO; /* force PIO mode */ eth_bmem = 0; #endif eth_vendor = VENDOR_3COM; /* Need this to make ns8390_poll() happy. */ eth_rmem = eth_bmem - 0x2000; /* Reset NIC and ASIC */ outb(_3COM_CR_RST | _3COM_CR_XSEL, eth_asic_base + _3COM_CR ); outb(_3COM_CR_XSEL, eth_asic_base + _3COM_CR ); /* Get our ethernet address */ outb(_3COM_CR_EALO | _3COM_CR_XSEL, eth_asic_base + _3COM_CR); nic->ioaddr = eth_nic_base; DBG ( "\n3Com 3c503 base %4.4x, ", eth_nic_base ); if (eth_flags & FLAG_PIO) DBG ( "PIO mode" ); else DBG ( "memory %4.4x", eth_bmem ); for (i=0; inode_addr[i] = inb(eth_nic_base+i); } DBG ( ", %s, MAC Addr %s\n", nic->flags ? "AUI" : "internal xcvr", eth_ntoa ( nic->node_addr ) ); outb(_3COM_CR_XSEL, eth_asic_base + _3COM_CR); /* * Initialize GA configuration register. Set bank and enable shared * mem. We always use bank 1. Disable interrupts. */ outb(_3COM_GACFR_RSEL | _3COM_GACFR_MBS0 | _3COM_GACFR_TCM | _3COM_GACFR_NIM, eth_asic_base + _3COM_GACFR); outb(0xff, eth_asic_base + _3COM_VPTR2); outb(0xff, eth_asic_base + _3COM_VPTR1); outb(0x00, eth_asic_base + _3COM_VPTR0); /* * Clear memory and verify that it worked (we use only 8K) */ if (!(eth_flags & FLAG_PIO)) { memset(bus_to_virt(eth_bmem), 0, 0x2000); for(i = 0; i < 0x2000; ++i) if (*((char *)(bus_to_virt(eth_bmem+i)))) { printf ("Failed to clear 3c503 shared mem.\n"); return (0); } } /* * Initialize GA page/start/stop registers. */ outb(eth_tx_start, eth_asic_base + _3COM_PSTR); outb(eth_memsize, eth_asic_base + _3COM_PSPR); } #endif #if defined(INCLUDE_NE) || defined(INCLUDE_NS8390) { /****************************************************************** Search for NE1000/2000 if no WD/SMC or 3com cards ******************************************************************/ unsigned char c; if (eth_vendor == VENDOR_NONE) { unsigned char romdata[16]; unsigned char testbuf[32]; int idx; static unsigned char test[] = "NE*000 memory"; static unsigned short base[] = { #ifdef NE_SCAN NE_SCAN, #endif 0 }; /* if no addresses supplied, fall back on defaults */ if (probe_addrs == NULL || probe_addrs[0] == 0) probe_addrs = base; eth_bmem = 0; /* No shared memory */ for (idx = 0; (eth_nic_base = probe_addrs[idx]) != 0; ++idx) { eth_flags = FLAG_PIO; eth_asic_base = eth_nic_base + NE_ASIC_OFFSET; eth_memsize = MEM_16384; eth_tx_start = 32; eth_rx_start = 32 + D8390_TXBUF_SIZE; c = inb(eth_asic_base + NE_RESET); outb(c, eth_asic_base + NE_RESET); (void) inb(0x84); outb(D8390_COMMAND_STP | D8390_COMMAND_RD2, eth_nic_base + D8390_P0_COMMAND); outb(D8390_RCR_MON, eth_nic_base + D8390_P0_RCR); outb(D8390_DCR_FT1 | D8390_DCR_LS, eth_nic_base + D8390_P0_DCR); outb(MEM_8192, eth_nic_base + D8390_P0_PSTART); outb(MEM_16384, eth_nic_base + D8390_P0_PSTOP); #ifdef NS8390_FORCE_16BIT eth_flags |= FLAG_16BIT; /* force 16-bit mode */ #endif eth_pio_write( (unsigned char *) test, 8192, sizeof(test)); eth_pio_read(8192, testbuf, sizeof(test)); if (!memcmp(test, testbuf, sizeof(test))) break; eth_flags |= FLAG_16BIT; eth_memsize = MEM_32768; eth_tx_start = 64; eth_rx_start = 64 + D8390_TXBUF_SIZE; outb(D8390_DCR_WTS | D8390_DCR_FT1 | D8390_DCR_LS, eth_nic_base + D8390_P0_DCR); outb(MEM_16384, eth_nic_base + D8390_P0_PSTART); outb(MEM_32768, eth_nic_base + D8390_P0_PSTOP); eth_pio_write( (unsigned char *) test, 16384, sizeof(test)); eth_pio_read(16384, testbuf, sizeof(test)); if (!memcmp(testbuf, test, sizeof(test))) break; } if (eth_nic_base == 0) return (0); if (eth_nic_base > ISA_MAX_ADDR) /* PCI probably */ eth_flags |= FLAG_16BIT; eth_vendor = VENDOR_NOVELL; eth_pio_read(0, romdata, sizeof(romdata)); for (i=0; inode_addr[i] = romdata[i + ((eth_flags & FLAG_16BIT) ? i : 0)]; } nic->ioaddr = eth_nic_base; DBG ( "\nNE%c000 base %4.4x, MAC Addr %s\n", (eth_flags & FLAG_16BIT) ? '2' : '1', eth_nic_base, eth_ntoa ( nic->node_addr ) ); } } #endif if (eth_vendor == VENDOR_NONE) return(0); if (eth_vendor != VENDOR_3COM) eth_rmem = eth_bmem; ns8390_reset(nic); nic->nic_op = &ns8390_operations; /* Based on PnP ISA map */ #ifdef INCLUDE_WD dev->devid.vendor_id = htons(GENERIC_ISAPNP_VENDOR); dev->devid.device_id = htons(0x812a); #endif #ifdef INCLUDE_3C503 dev->devid.vendor_id = htons(GENERIC_ISAPNP_VENDOR); dev->devid.device_id = htons(0x80f3); #endif #ifdef INCLUDE_NE dev->devid.vendor_id = htons(GENERIC_ISAPNP_VENDOR); dev->devid.device_id = htons(0x80d6); #endif return 1; } #ifdef INCLUDE_WD struct isa_driver wd_driver __isa_driver = { .type = NIC_DRIVER, .name = "WD", .probe = wd_probe, .ioaddrs = 0, }; ISA_ROM("wd","WD8003/8013, SMC8216/8416, SMC 83c790 (EtherEZ)"); #endif #ifdef INCLUDE_3C503 struct isa_driver t503_driver __isa_driver = { .type = NIC_DRIVER, .name = "3C503", .probe = t503_probe, .ioaddrs = 0, }; ISA_ROM("3c503","3Com503, Etherlink II[/16]"); #endif #ifdef INCLUDE_NE struct isa_driver ne_driver __isa_driver = { .type = NIC_DRIVER, .name = "NE*000", .probe = ne_probe, .ioaddrs = 0, }; ISA_ROM("ne","NE1000/2000 and clones"); #endif #ifdef INCLUDE_NS8390 static struct pci_device_id nepci_nics[] = { /* A few NE2000 PCI clones, list not exhaustive */ PCI_ROM(0x10ec, 0x8029, "rtl8029", "Realtek 8029", 0), PCI_ROM(0x1186, 0x0300, "dlink-528", "D-Link DE-528", 0), PCI_ROM(0x1050, 0x0940, "winbond940", "Winbond NE2000-PCI", 0), /* Winbond 86C940 / 89C940 */ PCI_ROM(0x1050, 0x5a5a, "winbond940f", "Winbond W89c940F", 0), /* Winbond 89C940F */ PCI_ROM(0x11f6, 0x1401, "compexrl2000", "Compex ReadyLink 2000", 0), PCI_ROM(0x8e2e, 0x3000, "ktiet32p2", "KTI ET32P2", 0), PCI_ROM(0x4a14, 0x5000, "nv5000sc", "NetVin NV5000SC", 0), PCI_ROM(0x12c3, 0x0058, "holtek80232", "Holtek HT80232", 0), PCI_ROM(0x12c3, 0x5598, "holtek80229", "Holtek HT80229", 0), PCI_ROM(0x10bd, 0x0e34, "surecom-ne34", "Surecom NE34", 0), PCI_ROM(0x1106, 0x0926, "via86c926", "Via 86c926", 0), }; PCI_DRIVER ( nepci_driver, nepci_nics, PCI_NO_CLASS ); DRIVER ( "NE2000/PCI", nic_driver, pci_driver, nepci_driver, nepci_probe, ns8390_disable ); #endif /* INCLUDE_NS8390 */ #endif /* * Local variables: * c-basic-offset: 8 * c-indent-level: 8 * tab-width: 8 * End: */