/* * Copyright (c) 1993 Herb Peyerl (hpeyerl@novatel.ca) All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions are * met: 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. 2. The name * of the author may not be used to endorse or promote products derived from * this software withough specific prior written permission * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * * if_epreg.h,v 1.4 1994/11/13 10:12:37 gibbs Exp Modified by: * October 2, 1994 Modified by: Andres Vega Garcia INRIA - Sophia Antipolis, France e-mail: avega@sophia.inria.fr finger: avega@pax.inria.fr */ FILE_LICENCE ( BSD3 ); #include "nic.h" /* * Ethernet software status per interface. */ /* * Some global constants */ #define TX_INIT_RATE 16 #define TX_INIT_MAX_RATE 64 #define RX_INIT_LATENCY 64 #define RX_INIT_EARLY_THRESH 64 #define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */ #define MIN_RX_EARLY_THRESHL 4 #define EEPROMSIZE 0x40 #define MAX_EEPROMBUSY 1000 #define EP_ID_PORT_START 0x110 /* avoid 0x100 to avoid conflict with SB16 */ #define EP_ID_PORT_INC 0x10 #define EP_ID_PORT_END 0x200 #define EP_TAG_MAX 0x7 /* must be 2^n - 1 */ /* * Commands to read/write EEPROM trough EEPROM command register (Window 0, * Offset 0xa) */ #define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */ #define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */ #define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */ #define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */ #define EEPROM_BUSY (1<<15) #define EEPROM_TST_MODE (1<<14) /* * Some short functions, worth to let them be a macro */ #define is_eeprom_busy(b) (inw((b)+EP_W0_EEPROM_COMMAND)&EEPROM_BUSY) #define GO_WINDOW(b,x) outw(WINDOW_SELECT|(x), (b)+EP_COMMAND) /************************************************************************** * * These define the EEPROM data structure. They are used in the probe * function to verify the existence of the adapter after having sent * the ID_Sequence. * * There are others but only the ones we use are defined here. * **************************************************************************/ #define EEPROM_NODE_ADDR_0 0x0 /* Word */ #define EEPROM_NODE_ADDR_1 0x1 /* Word */ #define EEPROM_NODE_ADDR_2 0x2 /* Word */ #define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ #define EEPROM_MFG_ID 0x7 /* 0x6d50 */ #define EEPROM_ADDR_CFG 0x8 /* Base addr */ #define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ /************************************************************************** * * These are the registers for the 3Com 3c509 and their bit patterns when * applicable. They have been taken out the the "EtherLink III Parallel * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual * from 3com. * * Getting this document out of 3Com is almost impossible. However, * archived copies are available at * http://www.osdever.net/cottontail/downloads/docs/3c5x9b.zip and * several other places on the web (search for 3c5x9b.pdf). * **************************************************************************/ #define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a * command reg. */ #define EP_STATUS 0x0e /* Read. BASE+0x0e is always status * reg. */ #define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window * reg. */ /* * Window 0 registers. Setup. */ /* Write */ #define EP_W0_EEPROM_DATA 0x0c #define EP_W0_EEPROM_COMMAND 0x0a #define EP_W0_RESOURCE_CFG 0x08 #define EP_W0_ADDRESS_CFG 0x06 #define EP_W0_CONFIG_CTRL 0x04 /* Read */ #define EP_W0_PRODUCT_ID 0x02 #define EP_W0_MFG_ID 0x00 /* * Window 1 registers. Operating Set. */ /* Write */ #define EP_W1_TX_PIO_WR_2 0x02 #define EP_W1_TX_PIO_WR_1 0x00 /* Read */ #define EP_W1_FREE_TX 0x0c #define EP_W1_TX_STATUS 0x0b /* byte */ #define EP_W1_TIMER 0x0a /* byte */ #define EP_W1_RX_STATUS 0x08 #define EP_W1_RX_PIO_RD_2 0x02 #define EP_W1_RX_PIO_RD_1 0x00 /* * Window 2 registers. Station Address Setup/Read */ /* Read/Write */ #define EP_W2_ADDR_5 0x05 #define EP_W2_ADDR_4 0x04 #define EP_W2_ADDR_3 0x03 #define EP_W2_ADDR_2 0x02 #define EP_W2_ADDR_1 0x01 #define EP_W2_ADDR_0 0x00 /* * Window 3 registers. FIFO Management. */ /* Read */ #define EP_W3_FREE_TX 0x0c #define EP_W3_FREE_RX 0x0a /* * Window 4 registers. Diagnostics. */ /* Read/Write */ #define EP_W4_MEDIA_TYPE 0x0a #define EP_W4_CTRLR_STATUS 0x08 #define EP_W4_NET_DIAG 0x06 #define EP_W4_FIFO_DIAG 0x04 #define EP_W4_HOST_DIAG 0x02 #define EP_W4_TX_DIAG 0x00 /* * Window 5 Registers. Results and Internal status. */ /* Read */ #define EP_W5_READ_0_MASK 0x0c #define EP_W5_INTR_MASK 0x0a #define EP_W5_RX_FILTER 0x08 #define EP_W5_RX_EARLY_THRESH 0x06 #define EP_W5_TX_AVAIL_THRESH 0x02 #define EP_W5_TX_START_THRESH 0x00 /* * Window 6 registers. Statistics. */ /* Read/Write */ #define TX_TOTAL_OK 0x0c #define RX_TOTAL_OK 0x0a #define TX_DEFERRALS 0x08 #define RX_FRAMES_OK 0x07 #define TX_FRAMES_OK 0x06 #define RX_OVERRUNS 0x05 #define TX_COLLISIONS 0x04 #define TX_AFTER_1_COLLISION 0x03 #define TX_AFTER_X_COLLISIONS 0x02 #define TX_NO_SQE 0x01 #define TX_CD_LOST 0x00 /**************************************** * * Register definitions. * ****************************************/ /* * Command register. All windows. * * 16 bit register. * 15-11: 5-bit code for command to be executed. * 10-0: 11-bit arg if any. For commands with no args; * this can be set to anything. */ #define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms * after issuing */ #define WINDOW_SELECT (unsigned short) (0x1<<11) #define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to * determine whether * this is needed. If * so; wait 800 uSec * before using trans- * ceiver. */ #define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on * power-up */ #define RX_ENABLE (unsigned short) (0x4<<11) #define RX_RESET (unsigned short) (0x5<<11) #define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11) #define TX_ENABLE (unsigned short) (0x9<<11) #define TX_DISABLE (unsigned short) (0xa<<11) #define TX_RESET (unsigned short) (0xb<<11) #define REQ_INTR (unsigned short) (0xc<<11) #define SET_INTR_MASK (unsigned short) (0xe<<11) #define SET_RD_0_MASK (unsigned short) (0xf<<11) #define SET_RX_FILTER (unsigned short) (0x10<<11) #define FIL_INDIVIDUAL (unsigned short) (0x1) #define FIL_GROUP (unsigned short) (0x2) #define FIL_BRDCST (unsigned short) (0x4) #define FIL_ALL (unsigned short) (0x8) #define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11) #define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11) #define SET_TX_START_THRESH (unsigned short) (0x13<<11) #define STATS_ENABLE (unsigned short) (0x15<<11) #define STATS_DISABLE (unsigned short) (0x16<<11) #define STOP_TRANSCEIVER (unsigned short) (0x17<<11) /* * The following C_* acknowledge the various interrupts. Some of them don't * do anything. See the manual. */ #define ACK_INTR (unsigned short) (0x6800) #define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1) #define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2) #define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4) #define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8) #define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10) #define C_RX_EARLY (unsigned short) (ACK_INTR|0x20) #define C_INT_RQD (unsigned short) (ACK_INTR|0x40) #define C_UPD_STATS (unsigned short) (ACK_INTR|0x80) /* * Status register. All windows. * * 15-13: Window number(0-7). * 12: Command_in_progress. * 11: reserved. * 10: reserved. * 9: reserved. * 8: reserved. * 7: Update Statistics. * 6: Interrupt Requested. * 5: RX Early. * 4: RX Complete. * 3: TX Available. * 2: TX Complete. * 1: Adapter Failure. * 0: Interrupt Latch. */ #define S_INTR_LATCH (unsigned short) (0x1) #define S_CARD_FAILURE (unsigned short) (0x2) #define S_TX_COMPLETE (unsigned short) (0x4) #define S_TX_AVAIL (unsigned short) (0x8) #define S_RX_COMPLETE (unsigned short) (0x10) #define S_RX_EARLY (unsigned short) (0x20) #define S_INT_RQD (unsigned short) (0x40) #define S_UPD_STATS (unsigned short) (0x80) #define S_5_INTS (S_CARD_FAILURE|S_TX_COMPLETE|\ S_TX_AVAIL|S_RX_COMPLETE|S_RX_EARLY) #define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000) /* * FIFO Registers. * RX Status. Window 1/Port 08 * * 15: Incomplete or FIFO empty. * 14: 1: Error in RX Packet 0: Incomplete or no error. * 13-11: Type of error. * 1000 = Overrun. * 1011 = Run Packet Error. * 1100 = Alignment Error. * 1101 = CRC Error. * 1001 = Oversize Packet Error (>1514 bytes) * 0010 = Dribble Bits. * (all other error codes, no errors.) * * 10-0: RX Bytes (0-1514) */ #define ERR_RX_INCOMPLETE (unsigned short) (0x1<<15) #define ERR_RX (unsigned short) (0x1<<14) #define ERR_RX_OVERRUN (unsigned short) (0x8<<11) #define ERR_RX_RUN_PKT (unsigned short) (0xb<<11) #define ERR_RX_ALIGN (unsigned short) (0xc<<11) #define ERR_RX_CRC (unsigned short) (0xd<<11) #define ERR_RX_OVERSIZE (unsigned short) (0x9<<11) #define ERR_RX_DRIBBLE (unsigned short) (0x2<<11) /* * FIFO Registers. * TX Status. Window 1/Port 0B * * Reports the transmit status of a completed transmission. Writing this * register pops the transmit completion stack. * * Window 1/Port 0x0b. * * 7: Complete * 6: Interrupt on successful transmission requested. * 5: Jabber Error (TP Only, TX Reset required. ) * 4: Underrun (TX Reset required. ) * 3: Maximum Collisions. * 2: TX Status Overflow. * 1-0: Undefined. * */ #define TXS_COMPLETE 0x80 #define TXS_SUCCES_INTR_REQ 0x40 #define TXS_JABBER 0x20 #define TXS_UNDERRUN 0x10 #define TXS_MAX_COLLISION 0x8 #define TXS_STATUS_OVERFLOW 0x4 /* * Configuration control register. * Window 0/Port 04 */ /* Read */ #define IS_AUI (1<<13) #define IS_BNC (1<<12) #define IS_UTP (1<<9) /* Write */ #define ENABLE_DRQ_IRQ 0x0001 #define W0_P4_CMD_RESET_ADAPTER 0x4 #define W0_P4_CMD_ENABLE_ADAPTER 0x1 /* * Media type and status. * Window 4/Port 0A */ #define ENABLE_UTP 0xc0 #define DISABLE_UTP 0x0 /* * Resource control register */ #define SET_IRQ(i) ( ((i)<<12) | 0xF00) /* set IRQ i */ /* * Receive status register */ #define RX_BYTES_MASK (unsigned short) (0x07ff) #define RX_ERROR 0x4000 #define RX_INCOMPLETE 0x8000 /* * Misc defines for various things. */ #define MFG_ID 0x6d50 /* in EEPROM and W0 ADDR_CONFIG */ #define PROD_ID 0x9150 #define AUI 0x1 #define BNC 0x2 #define UTP 0x4 #define RX_BYTES_MASK (unsigned short) (0x07ff) /* * Function shared between 3c509.c and 3c529.c */ extern int t5x9_probe ( struct nic *nic, uint16_t prod_id_check, uint16_t prod_id_mask ); extern void t5x9_disable ( struct nic *nic ); /* * Local variables: * c-basic-offset: 8 * End: */