+++ /dev/null
-#!/usr/bin/env bash
-
-#Deploy script to install provisioning server for Foreman/QuickStack
-#author: Tim Rozet (trozet@redhat.com)
-#
-#Uses Vagrant and VirtualBox
-#VagrantFile uses bootsrap.sh which Installs Khaleesi
-#Khaleesi will install and configure Foreman/QuickStack
-#
-#Pre-requisties:
-#Supports 3 or 4 network interface configuration
-#Target system must be RPM based
-#Ensure the host's kernel is up to date (yum update)
-#Provisioned nodes expected to have following order of network connections (note: not all have to exist, but order is maintained):
-#eth0- admin network
-#eth1- private network (+storage network in 3 NIC config)
-#eth2- public network
-#eth3- storage network
-#script assumes /24 subnet mask
-
-##VARS
-reset=`tput sgr0`
-blue=`tput setaf 4`
-red=`tput setaf 1`
-green=`tput setaf 2`
-
-declare -A interface_arr
-declare -A controllers_ip_arr
-declare -A admin_ip_arr
-declare -A public_ip_arr
-
-vagrant_box_dir=~/.vagrant.d/boxes/opnfv-VAGRANTSLASH-centos-7.0/1.0.0/virtualbox/
-vagrant_box_vmdk=box-disk1.vmdk
-vm_dir=/var/opt/opnfv
-script=`realpath $0`
-##END VARS
-
-##FUNCTIONS
-display_usage() {
- echo -e "\n\n${blue}This script is used to deploy Foreman/QuickStack Installer and Provision OPNFV Target System${reset}\n\n"
- echo -e "\n${green}Make sure you have the latest kernel installed before running this script! (yum update kernel +reboot)${reset}\n"
- echo -e "\nUsage:\n$0 [arguments] \n"
- echo -e "\n -no_parse : No variable parsing into config. Flag. \n"
- echo -e "\n -base_config : Full path of settings file to parse. Optional. Will provide a new base settings file rather than the default. Example: -base_config /opt/myinventory.yml \n"
- echo -e "\n -virtual : Node virtualization instead of baremetal. Flag. \n"
- echo -e "\n -enable_virtual_dhcp : Run dhcp server instead of using static IPs. Use this with -virtual only. \n"
- echo -e "\n -static_ip_range : static IP range to define when using virtual and when dhcp is not being used (default), must at least a 20 IP block. Format: '192.168.1.1,192.168.1.20' \n"
- echo -e "\n -ping_site : site to use to verify IP connectivity from the VM when -virtual is used. Format: -ping_site www.blah.com \n"
- echo -e "\n -floating_ip_count : number of IP address from the public range to be used for floating IP. Default is 20.\n"
- echo -e "\n -admin_nic : Baremetal NIC for the admin network. Required if other "nic" arguments are used. \
-Not applicable with -virtual. Example: -admin_nic em1"
- echo -e "\n -private_nic : Baremetal NIC for the private network. Required if other "nic" arguments are used. \
-Not applicable with -virtual. Example: -private_nic em2"
- echo -e "\n -public_nic : Baremetal NIC for the public network. Required if other "nic" arguments are used. \
-Can also be used with -virtual. Example: -public_nic em3"
- echo -e "\n -storage_nic : Baremetal NIC for the storage network. Optional. Not applicable with -virtual. \
-Private NIC will be used for storage if not specified. Example: -storage_nic em4"
- echo -e "\n -single_baremetal_nic : Baremetal NIC for the all in one network. Optional. Not applicable with -virtual. \
-Example: -single_baremetal_nic em1"
-}
-
-##verify vm dir exists
-##params: none
-function verify_vm_dir {
- if [ -d "$vm_dir" ]; then
- echo -e "\n\n${red}ERROR: VM Directory: $vm_dir already exists. Environment not clean. Please use clean.sh. Exiting${reset}\n\n"
- exit 1
- else
- mkdir -p $vm_dir
- fi
-
- chmod 700 $vm_dir
-
- if [ ! -d $vm_dir ]; then
- echo -e "\n\n${red}ERROR: Unable to create VM Directory: $vm_dir Exiting${reset}\n\n"
- exit -1
- fi
-}
-
-##find ip of interface
-##params: interface name
-function find_ip {
- ip addr show $1 | grep -Eo '^\s+inet\s+[\.0-9]+' | awk '{print $2}'
-}
-
-##finds subnet of ip and netmask
-##params: ip, netmask
-function find_subnet {
- IFS=. read -r i1 i2 i3 i4 <<< "$1"
- IFS=. read -r m1 m2 m3 m4 <<< "$2"
- printf "%d.%d.%d.%d\n" "$((i1 & m1))" "$((i2 & m2))" "$((i3 & m3))" "$((i4 & m4))"
-}
-
-##verify subnet has at least n IPs
-##params: subnet mask, n IPs
-function verify_subnet_size {
- IFS=. read -r i1 i2 i3 i4 <<< "$1"
- num_ips_required=$2
-
- ##this function assumes you would never need more than 254
- ##we check here to make sure
- if [ "$num_ips_required" -ge 254 ]; then
- echo -e "\n\n${red}ERROR: allocating more than 254 IPs is unsupported...Exiting${reset}\n\n"
- return 1
- fi
-
- ##we just return if 3rd octet is not 255
- ##because we know the subnet is big enough
- if [ "$i3" -ne 255 ]; then
- return 0
- elif [ $((254-$i4)) -ge "$num_ips_required" ]; then
- return 0
- else
- echo -e "\n\n${red}ERROR: Subnet is too small${reset}\n\n"
- return 1
- fi
-}
-
-##finds last usable ip (broadcast minus 1) of a subnet from an IP and netmask
-## Warning: This function only works for IPv4 at the moment.
-##params: ip, netmask
-function find_last_ip_subnet {
- IFS=. read -r i1 i2 i3 i4 <<< "$1"
- IFS=. read -r m1 m2 m3 m4 <<< "$2"
- IFS=. read -r s1 s2 s3 s4 <<< "$((i1 & m1)).$((i2 & m2)).$((i3 & m3)).$((i4 & m4))"
- printf "%d.%d.%d.%d\n" "$((255 - $m1 + $s1))" "$((255 - $m2 + $s2))" "$((255 - $m3 + $s3))" "$((255 - $m4 + $s4 - 1))"
-}
-
-##increments subnet by a value
-##params: ip, value
-##assumes low value
-function increment_subnet {
- IFS=. read -r i1 i2 i3 i4 <<< "$1"
- printf "%d.%d.%d.%d\n" "$i1" "$i2" "$i3" "$((i4 | $2))"
-}
-
-
-##finds netmask of interface
-##params: interface
-##returns long format 255.255.x.x
-function find_netmask {
- ifconfig $1 | grep -Eo 'netmask\s+[\.0-9]+' | awk '{print $2}'
-}
-
-##finds short netmask of interface
-##params: interface
-##returns short format, ex: /21
-function find_short_netmask {
- echo "/$(ip addr show $1 | grep -Eo '^\s+inet\s+[\/\.0-9]+' | awk '{print $2}' | cut -d / -f2)"
-}
-
-##increments next IP
-##params: ip
-##assumes a /24 subnet
-function next_ip {
- baseaddr="$(echo $1 | cut -d. -f1-3)"
- lsv="$(echo $1 | cut -d. -f4)"
- if [ "$lsv" -ge 254 ]; then
- return 1
- fi
- ((lsv++))
- echo $baseaddr.$lsv
-}
-
-##subtracts a value from an IP address
-##params: last ip, ip_count
-##assumes ip_count is less than the last octect of the address
-subtract_ip() {
- IFS=. read -r i1 i2 i3 i4 <<< "$1"
- ip_count=$2
- if [ $i4 -lt $ip_count ]; then
- echo -e "\n\n${red}ERROR: Can't subtract $ip_count from IP address $1 Exiting${reset}\n\n"
- exit 1
- fi
- printf "%d.%d.%d.%d\n" "$i1" "$i2" "$i3" "$((i4 - $ip_count ))"
-}
-
-##removes the network interface config from Vagrantfile
-##params: interface
-##assumes you are in the directory of Vagrantfile
-function remove_vagrant_network {
- sed -i 's/^.*'"$1"'.*$//' Vagrantfile
-}
-
-##check if IP is in use
-##params: ip
-##ping ip to get arp entry, then check arp
-function is_ip_used {
- ping -c 5 $1 > /dev/null 2>&1
- arp -n | grep "$1 " | grep -iv incomplete > /dev/null 2>&1
-}
-
-##find next usable IP
-##params: ip
-function next_usable_ip {
- new_ip=$(next_ip $1)
- while [ "$new_ip" ]; do
- if ! is_ip_used $new_ip; then
- echo $new_ip
- return 0
- fi
- new_ip=$(next_ip $new_ip)
- done
- return 1
-}
-
-##increment ip by value
-##params: ip, amount to increment by
-##increment_ip $next_private_ip 10
-function increment_ip {
- baseaddr="$(echo $1 | cut -d. -f1-3)"
- lsv="$(echo $1 | cut -d. -f4)"
- incrval=$2
- lsv=$((lsv+incrval))
- if [ "$lsv" -ge 254 ]; then
- return 1
- fi
- echo $baseaddr.$lsv
-}
-
-##translates yaml into variables
-##params: filename, prefix (ex. "config_")
-##usage: parse_yaml opnfv_ksgen_settings.yml "config_"
-parse_yaml() {
- local prefix=$2
- local s='[[:space:]]*' w='[a-zA-Z0-9_]*' fs=$(echo @|tr @ '\034')
- sed -ne "s|^\($s\)\($w\)$s:$s\"\(.*\)\"$s\$|\1$fs\2$fs\3|p" \
- -e "s|^\($s\)\($w\)$s:$s\(.*\)$s\$|\1$fs\2$fs\3|p" $1 |
- awk -F$fs '{
- indent = length($1)/2;
- vname[indent] = $2;
- for (i in vname) {if (i > indent) {delete vname[i]}}
- if (length($3) > 0) {
- vn=""; for (i=0; i<indent; i++) {vn=(vn)(vname[i])("_")}
- printf("%s%s%s=\"%s\"\n", "'$prefix'",vn, $2, $3);
- }
- }'
-}
-
-##translates the command line paramaters into variables
-##params: $@ the entire command line is passed
-##usage: parse_cmd_line() "$@"
-parse_cmdline() {
- if [[ ( $1 == "--help") || $1 == "-h" ]]; then
- display_usage
- exit 0
- fi
-
- echo -e "\n\n${blue}This script is used to deploy Foreman/QuickStack Installer and Provision OPNFV Target System${reset}\n\n"
- echo "Use -h to display help"
- sleep 2
-
- while [ "`echo $1 | cut -c1`" = "-" ]
- do
- echo $1
- case "$1" in
- -base_config)
- base_config=$2
- shift 2
- ;;
- -no_parse)
- no_parse="TRUE"
- shift 1
- ;;
- -virtual)
- virtual="TRUE"
- shift 1
- ;;
- -enable_virtual_dhcp)
- enable_virtual_dhcp="TRUE"
- shift 1
- ;;
- -static_ip_range)
- static_ip_range=$2
- shift 2
- ;;
- -ping_site)
- ping_site=$2
- shift 2
- ;;
- -floating_ip_count)
- floating_ip_count=$2
- shift 2
- ;;
- -admin_nic)
- admin_nic=$2
- shift 2
- nic_arg_flag=1
- ;;
- -private_nic)
- private_nic=$2
- shift 2
- nic_arg_flag=1
- ;;
- -public_nic)
- public_nic=$2
- shift 2
- nic_arg_flag=1
- ;;
- -storage_nic)
- storage_nic=$2
- shift 2
- nic_arg_flag=1
- ;;
- -single_baremetal_nic)
- single_baremetal_nic=$2
- shift 2
- ;;
- *)
- display_usage
- exit 1
- ;;
- esac
- done
-
- if [ ! -z "$enable_virtual_dhcp" ] && [ ! -z "$static_ip_range" ]; then
- echo -e "\n\n${red}ERROR: Incorrect Usage. Static IP range cannot be set when using DHCP!. Exiting${reset}\n\n"
- exit 1
- fi
-
- if [ -z "$virtual" ]; then
- if [ ! -z "$enable_virtual_dhcp" ]; then
- echo -e "\n\n${red}ERROR: Incorrect Usage. enable_virtual_dhcp can only be set when using -virtual!. Exiting${reset}\n\n"
- exit 1
- elif [ ! -z "$static_ip_range" ]; then
- echo -e "\n\n${red}ERROR: Incorrect Usage. static_ip_range can only be set when using -virtual!. Exiting${reset}\n\n"
- exit 1
- fi
- fi
-
- if [ -z "$floating_ip_count" ]; then
- floating_ip_count=20
- fi
-
- ##Validate nic args
- if [[ $nic_arg_flag -eq 1 ]]; then
- if [ ! -z "$single_baremetal_nic" ]; then
- echo "${red}Please do not specify other nic types along with single_baremetal_nic!${reset}"
- exit 1
- fi
-
- if [ -z "$virtual" ]; then
- for nic_type in admin_nic private_nic public_nic; do
- eval "nic_value=\$$nic_type"
- if [ -z "$nic_value" ]; then
- echo "${red}$nic_type is empty or not defined. Required when other nic args are given!${reset}"
- exit 1
- fi
- interface_ip=$(find_ip $nic_value)
- if [ ! "$interface_ip" ]; then
- echo "${red}$nic_value does not have an IP address! Exiting... ${reset}"
- exit 1
- fi
- done
- else
- ##if virtual only public_nic should be specified
- for nic_type in admin_nic private_nic storage_nic single_baremetal_nic; do
- eval "nic_value=\$$nic_type"
- if [ ! -z "$nic_value" ]; then
- echo "${red}$nic_type is not a valid argument using -virtual. Please only specify public_nic!${reset}"
- exit 1
- fi
- done
-
- interface_ip=$(find_ip $public_nic)
- if [ ! "$interface_ip" ]; then
- echo "${red}Public NIC: $public_nic does not have an IP address! Exiting... ${reset}"
- exit 1
- fi
- fi
- elif [ ! -z "$single_baremetal_nic" ]; then
- interface_ip=$(find_ip $single_baremetal_nic)
- if [ ! "$interface_ip" ]; then
- echo "${red}Single Baremetal NIC: $single_baremetal_nic does not have an IP address! Exiting... ${reset}"
- exit 1
- fi
- fi
-}
-
-##disable selinux
-##params: none
-##usage: disable_selinux()
-disable_selinux() {
- /sbin/setenforce 0
-}
-
-##Install the EPEL repository and additional packages
-##params: none
-##usage: install_EPEL()
-install_EPEL() {
- # Install EPEL repo for access to many other yum repos
- # Major version is pinned to force some consistency for Arno
- yum install -y epel-release-7*
-
- # Install other required packages
- # Major versions are pinned to force some consistency for Arno
- if ! yum install -y binutils-2* gcc-4* make-3* patch-2* libgomp-4* glibc-headers-2* glibc-devel-2* kernel-headers-3* kernel-devel-3* dkms-2* psmisc-22*; then
- printf '%s\n' 'deploy.sh: Unable to install depdency packages' >&2
- exit 1
- fi
-}
-
-##Download and install virtual box
-##params: none
-##usage: install_vbox()
-install_vbox() {
- ##install VirtualBox repo
- if cat /etc/*release | grep -i "Fedora release"; then
- vboxurl=http://download.virtualbox.org/virtualbox/rpm/fedora/\$releasever/\$basearch
- else
- vboxurl=http://download.virtualbox.org/virtualbox/rpm/el/\$releasever/\$basearch
- fi
-
- cat > /etc/yum.repos.d/virtualbox.repo << EOM
-[virtualbox]
-name=Oracle Linux / RHEL / CentOS-\$releasever / \$basearch - VirtualBox
-baseurl=$vboxurl
-enabled=1
-gpgcheck=1
-gpgkey=https://www.virtualbox.org/download/oracle_vbox.asc
-skip_if_unavailable = 1
-keepcache = 0
-EOM
-
- ##install VirtualBox
- if ! yum list installed | grep -i virtualbox; then
- if ! yum -y install VirtualBox-4.3; then
- printf '%s\n' 'deploy.sh: Unable to install virtualbox package' >&2
- exit 1
- fi
- fi
-
- ##install kmod-VirtualBox
- if ! lsmod | grep vboxdrv; then
- sudo /etc/init.d/vboxdrv setup
- if ! lsmod | grep vboxdrv; then
- printf '%s\n' 'deploy.sh: Unable to install kernel module for virtualbox' >&2
- exit 1
- fi
- else
- printf '%s\n' 'deploy.sh: Skipping kernel module for virtualbox. Already Installed'
- fi
-}
-
-##install Ansible using yum
-##params: none
-##usage: install_ansible()
-install_ansible() {
- if ! yum list installed | grep -i ansible; then
- if ! yum -y install ansible-1*; then
- printf '%s\n' 'deploy.sh: Unable to install Ansible package' >&2
- exit 1
- fi
- fi
-}
-
-##install Vagrant RPM directly with the bintray.com site
-##params: none
-##usage: install_vagrant()
-install_vagrant() {
- if ! rpm -qa | grep vagrant; then
- if ! rpm -Uvh https://dl.bintray.com/mitchellh/vagrant/vagrant_1.7.2_x86_64.rpm; then
- printf '%s\n' 'deploy.sh: Unable to install vagrant package' >&2
- exit 1
- fi
- else
- printf '%s\n' 'deploy.sh: Skipping Vagrant install as it is already installed.'
- fi
-
- ##add centos 7 box to vagrant
- if ! vagrant box list | grep opnfv/centos-7.0; then
- if ! vagrant box add opnfv/centos-7.0 --provider virtualbox; then
- printf '%s\n' 'deploy.sh: Unable to download centos7 box for Vagrant' >&2
- exit 1
- fi
- else
- printf '%s\n' 'deploy.sh: Skipping Vagrant box add as centos-7.0 is already installed.'
- fi
-
- ##install workaround for centos7
- if ! vagrant plugin list | grep vagrant-centos7_fix; then
- if ! vagrant plugin install vagrant-centos7_fix; then
- printf '%s\n' 'deploy.sh: Warning: unable to install vagrant centos7 workaround' >&2
- fi
- else
- printf '%s\n' 'deploy.sh: Skipping Vagrant plugin as centos7 workaround is already installed.'
- fi
-}
-
-
-##remove bgs vagrant incase it wasn't cleaned up
-##params: none
-##usage: clean_tmp()
-clean_tmp() {
- rm -rf $vm_dir/foreman_vm
-}
-
-##clone genesis and move to node vm dir
-##params: destination directory
-##usage: clone_bgs /tmp/myvm/
-clone_bgs() {
- script_dir="`dirname "$script"`"
- cp -fr $script_dir/ $1
- cp -fr $script_dir/../../common/puppet-opnfv $1
-}
-
-##validates the network settings and update VagrantFile with network settings
-##params: none
-##usage: configure_network()
-configure_network() {
- cd $vm_dir/foreman_vm
-
- ##if nic_arg_flag is set, then we don't figure out
- ##NICs dynamically
- if [[ $nic_arg_flag -eq 1 ]]; then
- echo "${blue}Static Network Interfaces Defined. Updating Vagrantfile...${reset}"
- if [ $virtual ]; then
- nic_list="$public_nic"
- elif [ -z "$storage_nic" ]; then
- echo "${blue}storage_nic not defined, will combine storage into private VLAN ${reset}"
- nic_list="$admin_nic $private_nic $public_nic"
- else
- nic_list="$admin_nic $private_nic $public_nic $storage_nic"
- fi
- nic_array=( $nic_list )
- output=$nic_list
- elif [ ! -z "$single_baremetal_nic" ]; then
- output=$single_baremetal_nic
- else
- echo "${blue}Detecting network configuration...${reset}"
- ##detect host 1 or 3 interface configuration
- #output=`ip link show | grep -E "^[0-9]" | grep -Ev ": lo|tun|virbr|vboxnet" | awk '{print $2}' | sed 's/://'`
- #output=`/bin/ls -l /sys/class/net | tail -n +2 | grep -v virtual | cut -d " " -f10`
- output=`/bin/ls -l /sys/class/net | tail -n +2 | grep -v virtual | awk {'print $9'}`
- fi
-
- if [ ! "$output" ]; then
- printf '%s\n' 'deploy.sh: Unable to detect interfaces to bridge to' >&2
- exit 1
- fi
-
- ##virtual we only find 1 interface
- if [ $virtual ]; then
- if [ ! -z "${nic_array[0]}" ]; then
- echo "${blue}Public Interface specified: ${nic_array[0]}${reset}"
- this_default_gw_interface=${nic_array[0]}
- else
- ##find interface with default gateway
- this_default_gw=$(ip route | grep default | awk '{print $3}')
- echo "${blue}Default Gateway: $this_default_gw ${reset}"
- this_default_gw_interface=$(ip route get $this_default_gw | awk '{print $3}')
- fi
-
- ##find interface IP, make sure its valid
- interface_ip=$(find_ip $this_default_gw_interface)
- if [ ! "$interface_ip" ]; then
- echo "${red}Interface ${this_default_gw_interface} does not have an IP: $interface_ip ! Exiting ${reset}"
- exit 1
- fi
-
- ##set variable info
- if [ ! -z "$static_ip_range" ]; then
- new_ip=$(echo $static_ip_range | cut -d , -f1)
- subnet_mask=$(find_netmask $this_default_gw_interface)
- host_subnet=$(find_subnet $interface_ip $subnet_mask)
- ip_range_subnet=$(find_subnet $new_ip $subnet_mask)
- if [ "$ip_range_subnet" != "$host_subnet" ]; then
- echo "${red}static_ip_range: ${static_ip_range} is not in the same subnet as your default gateway interface: ${host_subnet}. Please use a correct range!${reset}"
- exit 1
- fi
- else
- new_ip=$(next_usable_ip $interface_ip)
- if [ ! "$new_ip" ]; then
- echo "${red} Cannot find next IP on interface ${this_default_gw_interface} new_ip: $new_ip ! Exiting ${reset}"
- exit 1
- fi
- fi
- interface=$this_default_gw_interface
- public_interface=$interface
- interface_arr[$interface]=2
- interface_ip_arr[2]=$new_ip
- subnet_mask=$(find_netmask $interface)
- public_subnet_mask=$subnet_mask
- public_short_subnet_mask=$(find_short_netmask $interface)
-
- if ! verify_subnet_size $public_subnet_mask 25; then
- echo "${red} Not enough IPs in public subnet: $interface_ip_arr[2] ${public_subnet_mask}. Need at least 25 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
-
- ##set that interface to be public
- sed -i 's/^.*eth_replace2.*$/ config.vm.network "public_network", ip: '\""$new_ip"\"', bridge: '\'"$interface"\'', netmask: '\""$subnet_mask"\"'/' Vagrantfile
- if_counter=1
- else
- if [ ! -z $single_baremetal_nic ]; then
- interface_ip=$(find_ip $single_baremetal_nic)
- if [ ! "$interface_ip" ]; then
- echo "${red}Unable to determine IP address of $single_baremetal_nic. Exiting...${reset}"
- exit 1
- fi
- subnet_mask=$(find_netmask $single_baremetal_nic)
- public_subnet_mask=$subnet_mask
- if ! verify_subnet_size $public_subnet_mask 50; then
- echo "${red} Not enough IPs in subnet: $interface_ip $subnet_mask. Need at least 50 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
-
- new_ip=$(next_usable_ip $interface_ip)
- if [ ! "$new_ip" ]; then
- echo "${red}Unable to allocate new IP address: $interface_ip $subnet_mask Exiting...${reset}"
- exit 1
- fi
-
- this_default_gw=$(ip route | grep default | awk '{print $3}')
- echo "${blue}Default Gateway: $this_default_gw ${reset}"
- this_default_gw_interface=$(ip route get $this_default_gw | awk '{print $3}')
- if [ "$this_default_gw_interface" != "$single_baremetal_nic" ]; then
- echo "${red}Error: Your default gateway interface: $this_default_gw_interface does not \
-match the baremetal nic you provided: ${single_baremetal_nic}. Exiting...${reset}"
- exit 1
- fi
- sed -i 's/^.*eth_replace0.*$/ config.vm.network "public_network", ip: '\""$new_ip"\"', bridge: '\'"$single_baremetal_nic"\'', netmask: '\""$subnet_mask"\"'/' Vagrantfile
- interface_ip_arr[0]=$new_ip
- interface_arr[$single_baremetal_nic]=0
- admin_ip=$new_ip
- admin_subnet_mask=$subnet_mask
- public_short_subnet_mask=$(find_short_netmask $single_baremetal_nic)
- if_counter=1
- else
- ##find number of interfaces with ip and substitute in VagrantFile
- if_counter=0
- for interface in ${output}; do
-
- if [ "$if_counter" -ge 4 ]; then
- break
- fi
- interface_ip=$(find_ip $interface)
- if [ ! "$interface_ip" ]; then
- continue
- fi
- new_ip=$(next_usable_ip $interface_ip)
- if [ ! "$new_ip" ]; then
- continue
- fi
- interface_arr[$interface]=$if_counter
- interface_ip_arr[$if_counter]=$new_ip
- subnet_mask=$(find_netmask $interface)
- if [ "$if_counter" -eq 0 ]; then
- admin_subnet_mask=$subnet_mask
- admin_ip=$new_ip
- if ! verify_subnet_size $admin_subnet_mask 5; then
- echo "${red} Not enough IPs in admin subnet: ${interface_ip_arr[$if_counter]} ${admin_subnet_mask}. Need at least 5 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
-
- elif [ "$if_counter" -eq 1 ]; then
- private_subnet_mask=$subnet_mask
- private_short_subnet_mask=$(find_short_netmask $interface)
-
- if ! verify_subnet_size $private_subnet_mask 15; then
- echo "${red} Not enough IPs in private subnet: ${interface_ip_arr[$if_counter]} ${private_subnet_mask}. Need at least 15 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
- elif [ "$if_counter" -eq 2 ]; then
- public_subnet_mask=$subnet_mask
- public_short_subnet_mask=$(find_short_netmask $interface)
-
- if ! verify_subnet_size $public_subnet_mask 25; then
- echo "${red} Not enough IPs in public subnet: ${interface_ip_arr[$if_counter]} ${public_subnet_mask}. Need at least 25 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
- elif [ "$if_counter" -eq 3 ]; then
- storage_subnet_mask=$subnet_mask
-
- if ! verify_subnet_size $storage_subnet_mask 10; then
- echo "${red} Not enough IPs in storage subnet: ${interface_ip_arr[$if_counter]} ${storage_subnet_mask}. Need at least 10 IPs. Please resize subnet! Exiting ${reset}"
- exit 1
- fi
- else
- echo "${red}ERROR: interface counter outside valid range of 0 to 3: $if_counter ! ${reset}"
- exit 1
- fi
- sed -i 's/^.*eth_replace'"$if_counter"'.*$/ config.vm.network "public_network", ip: '\""$new_ip"\"', bridge: '\'"$interface"\'', netmask: '\""$subnet_mask"\"'/' Vagrantfile
- ((if_counter++))
- done
- fi
- fi
-
- ##now remove interface config in Vagrantfile for 1 node
- ##if 1, 3, or 4 interfaces set deployment type
- ##if 2 interfaces remove 2nd interface and set deployment type
- if [[ "$if_counter" == 1 || "$if_counter" == 2 ]]; then
- if [ $virtual ]; then
- deployment_type="single_network"
- echo "${blue}Single network detected for Virtual deployment...converting to three_network with internal networks! ${reset}"
- private_internal_ip=155.1.2.2
- admin_internal_ip=156.1.2.2
- private_subnet_mask=255.255.255.0
- private_short_subnet_mask=/24
- interface_ip_arr[1]=$private_internal_ip
- interface_ip_arr[0]=$admin_internal_ip
- admin_subnet_mask=255.255.255.0
- admin_short_subnet_mask=/24
- sed -i 's/^.*eth_replace1.*$/ config.vm.network "private_network", virtualbox__intnet: "my_private_network", ip: '\""$private_internal_ip"\"', netmask: '\""$private_subnet_mask"\"'/' Vagrantfile
- sed -i 's/^.*eth_replace0.*$/ config.vm.network "private_network", virtualbox__intnet: "my_admin_network", ip: '\""$admin_internal_ip"\"', netmask: '\""$private_subnet_mask"\"'/' Vagrantfile
- remove_vagrant_network eth_replace3
- deployment_type=three_network
- elif [[ "$if_counter" == 1 ]]; then
- echo "${blue}Single network detected for Baremetal deployment! ${reset}"
- remove_vagrant_network eth_replace1
- remove_vagrant_network eth_replace2
- remove_vagrant_network eth_replace3
- deployment_type="single_network"
- else
- echo "${blue}Single network or 2 network detected for baremetal deployment. This is unsupported! Exiting. ${reset}"
- exit 1
- fi
- elif [ "$if_counter" == 3 ]; then
- deployment_type="three_network"
- remove_vagrant_network eth_replace3
- else
- deployment_type="multi_network"
- fi
-
- echo "${blue}Network detected: ${deployment_type}! ${reset}"
-
- if [ $virtual ]; then
- if [ -z "$enable_virtual_dhcp" ]; then
- sed -i 's/^.*disable_dhcp_flag =.*$/ disable_dhcp_flag = true/' Vagrantfile
- if [ $static_ip_range ]; then
- ##verify static range is at least 20 IPs
- static_ip_range_begin=$(echo $static_ip_range | cut -d , -f1)
- static_ip_range_end=$(echo $static_ip_range | cut -d , -f2)
- ##verify range is at least 20 ips
- ##assumes less than 255 range pool
- begin_octet=$(echo $static_ip_range_begin | cut -d . -f4)
- end_octet=$(echo $static_ip_range_end | cut -d . -f4)
- ip_count=$((end_octet-begin_octet+1))
- if [ "$ip_count" -lt 20 ]; then
- echo "${red}Static range is less than 20 ips: ${ip_count}, exiting ${reset}"
- exit 1
- else
- echo "${blue}Static IP range is size $ip_count ${reset}"
- fi
- fi
- fi
- fi
-
- if route | grep default; then
- echo "${blue}Default Gateway Detected ${reset}"
- host_default_gw=$(ip route | grep default | awk '{print $3}')
- echo "${blue}Default Gateway: $host_default_gw ${reset}"
- default_gw_interface=$(ip route get $host_default_gw | awk '{print $3}')
- case "${interface_arr[$default_gw_interface]}" in
- 0)
- echo "${blue}Default Gateway Detected on Admin Interface!${reset}"
- sed -i 's/^.*default_gw =.*$/ default_gw = '\""$host_default_gw"\"'/' Vagrantfile
- node_default_gw=$host_default_gw
- ;;
- 1)
- echo "${red}Default Gateway Detected on Private Interface!${reset}"
- echo "${red}Private subnet should be private and not have Internet access!${reset}"
- exit 1
- ;;
- 2)
- echo "${blue}Default Gateway Detected on Public Interface!${reset}"
- sed -i 's/^.*default_gw =.*$/ default_gw = '\""$host_default_gw"\"'/' Vagrantfile
- echo "${blue}Will setup NAT from Admin -> Public Network on VM!${reset}"
- sed -i 's/^.*nat_flag =.*$/ nat_flag = true/' Vagrantfile
- echo "${blue}Setting node gateway to be VM Admin IP${reset}"
- node_default_gw=${interface_ip_arr[0]}
- public_gateway=$host_default_gw
- ;;
- 3)
- echo "${red}Default Gateway Detected on Storage Interface!${reset}"
- echo "${red}Storage subnet should be private and not have Internet access!${reset}"
- exit 1
- ;;
- *)
- echo "${red}Unable to determine which interface default gateway is on..Exiting!${reset}"
- exit 1
- ;;
- esac
- else
- #assumes 24 bit mask
- defaultgw=`echo ${interface_ip_arr[0]} | cut -d. -f1-3`
- firstip=.1
- defaultgw=$defaultgw$firstip
- echo "${blue}Unable to find default gateway. Assuming it is $defaultgw ${reset}"
- sed -i 's/^.*default_gw =.*$/ default_gw = '\""$defaultgw"\"'/' Vagrantfile
- node_default_gw=$defaultgw
- fi
-
- if [ $base_config ]; then
- if ! cp -f $base_config opnfv_ksgen_settings.yml; then
- echo "{red}ERROR: Unable to copy $base_config to opnfv_ksgen_settings.yml${reset}"
- exit 1
- fi
- fi
-
- nodes=`sed -nr '/nodes:/{:start /workaround/!{N;b start};//p}' opnfv_ksgen_settings.yml | sed -n '/^ [A-Za-z0-9]\+:$/p' | sed 's/\s*//g' | sed 's/://g'`
- controller_nodes=`echo $nodes | tr " " "\n" | grep controller | tr "\n" " "`
- echo "${blue}Controller nodes found in settings: ${controller_nodes}${reset}"
- my_controller_array=( $controller_nodes )
- num_control_nodes=${#my_controller_array[@]}
- if [ "$num_control_nodes" -ne 3 ]; then
- if cat opnfv_ksgen_settings.yml | grep ha_flag | grep true; then
- echo "${red}Error: You must define exactly 3 control nodes when HA flag is true!${reset}"
- exit 1
- fi
- else
- echo "${blue}Number of Controller nodes detected: ${num_control_nodes}${reset}"
- fi
-
- if [ $no_parse ]; then
- echo "${blue}Skipping parsing variables into settings file as no_parse flag is set${reset}"
-
- else
-
- echo "${blue}Gathering network parameters for Target System...this may take a few minutes${reset}"
- ##Edit the ksgen settings appropriately
- ##ksgen settings will be stored in /vagrant on the vagrant machine
- ##if single node deployment all the variables will have the same ip
- ##interface names will be enp0s3, enp0s8, enp0s9 in chef/centos7
-
- sed -i 's/^.*default_gw:.*$/default_gw:'" $node_default_gw"'/' opnfv_ksgen_settings.yml
-
- ##replace private interface parameter
- ##private interface will be of hosts, so we need to know the provisioned host interface name
- ##we add biosdevname=0, net.ifnames=0 to the kickstart to use regular interface naming convention on hosts
- ##replace IP for parameters with next IP that will be given to controller
-
- if [[ "$deployment_type" == "single_network" || "$deployment_type" == "multi_network" || "$deployment_type" == "three_network" ]]; then
-
- if [ "$deployment_type" == "three_network" ]; then
- sed -i 's/^.*network_type:.*$/network_type: three_network/' opnfv_ksgen_settings.yml
- elif [ "$deployment_type" == "single_network" ]; then
- sed -i 's/^.*network_type:.*$/network_type: single_network/' opnfv_ksgen_settings.yml
- next_single_ip=${interface_ip_arr[0]}
- foreman_ip=$next_single_ip
- next_single_ip=$(next_usable_ip $next_single_ip)
- fi
-
- sed -i 's/^.*deployment_type:.*$/ deployment_type: '"$deployment_type"'/' opnfv_ksgen_settings.yml
-
- ##get ip addresses for private network on controllers to make dhcp entries
- ##required for controllers_ip_array global param
- if [ "$deployment_type" == "single_network" ]; then
- next_private_ip=$next_single_ip
- sed -i 's/^.*no_dhcp:.*$/no_dhcp: true/' opnfv_ksgen_settings.yml
- nodes=`sed -nr '/nodes:/{:start /workaround/!{N;b start};//p}' opnfv_ksgen_settings.yml | sed -n '/^ [A-Za-z0-9]\+:$/p' | sed 's/\s*//g' | sed 's/://g'`
- compute_nodes=`echo $nodes | tr " " "\n" | grep -v controller | tr "\n" " "`
- controller_nodes=`echo $nodes | tr " " "\n" | grep controller | tr "\n" " "`
- nodes=${controller_nodes}${compute_nodes}
- next_admin_ip=${interface_ip_arr[0]}
- type1=_admin
- type2=_private
- control_count=0
- for node in ${controller_nodes}; do
- next_private_ip=$(next_usable_ip $next_private_ip)
- if [ ! "$next_private_ip" ]; then
- echo "${red} Unable to find an unused IP for $node ! ${reset}"
- exit 1
- else
- sed -i 's/'"$node$type1"'/'"$next_private_ip"'/g' opnfv_ksgen_settings.yml
- sed -i 's/'"$node$type2"'/'"$next_private_ip"'/g' opnfv_ksgen_settings.yml
- controller_ip_array=$controller_ip_array$next_private_ip,
- controllers_ip_arr[$control_count]=$next_private_ip
- ((control_count++))
- fi
- done
-
- for node in ${compute_nodes}; do
- next_private_ip=$(next_usable_ip $next_private_ip)
- if [ ! "$next_private_ip" ]; then
- echo "${red} Unable to find an unused IP for $node ! ${reset}"
- exit 1
- else
- sed -i 's/'"$node$type1"'/'"$next_private_ip"'/g' opnfv_ksgen_settings.yml
- fi
- done
-
- else
- next_private_ip=${interface_ip_arr[1]}
-
- type=_private
- control_count=0
- for node in controller1 controller2 controller3; do
- next_private_ip=$(next_usable_ip $next_private_ip)
- if [ ! "$next_private_ip" ]; then
- printf '%s\n' 'deploy.sh: Unable to find next ip for private network for control nodes' >&2
- exit 1
- fi
- sed -i 's/'"$node$type"'/'"$next_private_ip"'/g' opnfv_ksgen_settings.yml
- controller_ip_array=$controller_ip_array$next_private_ip,
- controllers_ip_arr[$control_count]=$next_private_ip
- ((control_count++))
- done
- fi
-
- if [[ "$deployment_type" != "single_network" ]]; then
- next_public_ip=${interface_ip_arr[2]}
- foreman_ip=$next_public_ip
- fi
-
- ##if no dhcp, find all the Admin IPs for nodes in advance
- if [ $virtual ]; then
- if [ -z "$enable_virtual_dhcp" ]; then
- sed -i 's/^.*no_dhcp:.*$/no_dhcp: true/' opnfv_ksgen_settings.yml
- nodes=`sed -nr '/nodes:/{:start /workaround/!{N;b start};//p}' opnfv_ksgen_settings.yml | sed -n '/^ [A-Za-z0-9]\+:$/p' | sed 's/\s*//g' | sed 's/://g'`
- compute_nodes=`echo $nodes | tr " " "\n" | grep -v controller | tr "\n" " "`
- controller_nodes=`echo $nodes | tr " " "\n" | grep controller | tr "\n" " "`
- nodes=${controller_nodes}${compute_nodes}
- next_admin_ip=${interface_ip_arr[0]}
- type=_admin
- for node in ${nodes}; do
- next_admin_ip=$(next_ip $next_admin_ip)
- if [ ! "$next_admin_ip" ]; then
- echo "${red} Unable to find an unused IP in admin_network for $node ! ${reset}"
- exit 1
- else
- admin_ip_arr[$node]=$next_admin_ip
- sed -i 's/'"$node$type"'/'"$next_admin_ip"'/g' opnfv_ksgen_settings.yml
- fi
- done
-
- ##allocate node public IPs
- for node in ${nodes}; do
- next_public_ip=$(next_usable_ip $next_public_ip)
- if [ ! "$next_public_ip" ]; then
- echo "${red} Unable to find an unused IP in admin_network for $node ! ${reset}"
- exit 1
- else
- public_ip_arr[$node]=$next_public_ip
- fi
- done
- fi
- fi
- ##replace global param for controllers_ip_array
- controller_ip_array=${controller_ip_array%?}
- sed -i 's/^.*controllers_ip_array:.*$/ controllers_ip_array: '"$controller_ip_array"'/' opnfv_ksgen_settings.yml
-
- ##now replace all the VIP variables. admin//private can be the same IP
- ##we have to use IP's here that won't be allocated to hosts at provisioning time
- ##therefore we increment the ip by 10 to make sure we have a safe buffer
- next_private_ip=$(increment_ip $next_private_ip 10)
-
- private_output=$(grep -E '*private_vip|loadbalancer_vip|db_vip|amqp_vip|*admin_vip' opnfv_ksgen_settings.yml)
- if [ ! -z "$private_output" ]; then
- while read -r line; do
- sed -i 's/^.*'"$line"'.*$/ '"$line $next_private_ip"'/' opnfv_ksgen_settings.yml
- next_private_ip=$(next_usable_ip $next_private_ip)
- if [ ! "$next_private_ip" ]; then
- printf '%s\n' 'deploy.sh: Unable to find next ip for private network for vip replacement' >&2
- exit 1
- fi
- done <<< "$private_output"
- fi
-
- ##replace odl_control_ip (non-HA only)
- odl_control_ip=${controllers_ip_arr[0]}
- sed -i 's/^.*odl_control_ip:.*$/ odl_control_ip: '"$odl_control_ip"'/' opnfv_ksgen_settings.yml
-
- ##replace controller_ip (non-HA only)
- sed -i 's/^.*controller_ip:.*$/ controller_ip: '"$odl_control_ip"'/' opnfv_ksgen_settings.yml
-
- ##replace foreman site
- sed -i 's/^.*foreman_url:.*$/ foreman_url:'" https:\/\/$foreman_ip"'\/api\/v2\//' opnfv_ksgen_settings.yml
- ##replace public vips
-
- ##if single_network deployment we continue next_public_ip from next_private_ip
- if [[ "$deployment_type" == "single_network" ]]; then
- next_public_ip=$(next_usable_ip $next_private_ip)
- else
- ##no need to do this if no dhcp
- if [[ -z "$enable_virtual_dhcp" && ! -z "$virtual" ]]; then
- next_public_ip=$(next_usable_ip $next_public_ip)
- else
- next_public_ip=$(increment_ip $next_public_ip 10)
- fi
- fi
-
- public_output=$(grep -E '*public_vip' opnfv_ksgen_settings.yml)
- if [ ! -z "$public_output" ]; then
- while read -r line; do
- if echo $line | grep horizon_public_vip; then
- horizon_public_vip=$next_public_ip
- fi
- sed -i 's/^.*'"$line"'.*$/ '"$line $next_public_ip"'/' opnfv_ksgen_settings.yml
- next_public_ip=$(next_usable_ip $next_public_ip)
- if [ ! "$next_public_ip" ]; then
- printf '%s\n' 'deploy.sh: Unable to find next ip for public network for vip replcement' >&2
- exit 1
- fi
- done <<< "$public_output"
- fi
-
- ##replace admin_network param for bare metal deployments
- if [[ -z "$virtual" && -z "$single_network" ]]; then
- admin_subnet=$(find_subnet $admin_ip $admin_subnet_mask)
- sed -i 's/^.*admin_network:.*$/ admin_network:'" $admin_subnet"'/' opnfv_ksgen_settings.yml
- else
- sed -i 's/^.*admin_network:.*$/ admin_network:'" \"false\""'/' opnfv_ksgen_settings.yml
- fi
- ##replace public_network param
- public_subnet=$(find_subnet $next_public_ip $public_subnet_mask)
- sed -i 's/^.*public_network:.*$/ public_network:'" $public_subnet"'/' opnfv_ksgen_settings.yml
- if [ "$deployment_type" == "single_network" ]; then
- sed -i 's/^.*private_network:.*$/ private_network:'" $public_subnet"'/' opnfv_ksgen_settings.yml
- else
- ##replace private_network param
- private_subnet=$(find_subnet $next_private_ip $private_subnet_mask)
- sed -i 's/^.*private_network:.*$/ private_network:'" $private_subnet"'/' opnfv_ksgen_settings.yml
- fi
-
- ##replace storage_network
- if [ "$deployment_type" == "single_network" ]; then
- sed -i 's/^.*storage_network:.*$/ storage_network:'" $public_subnet"'/' opnfv_ksgen_settings.yml
- elif [ "$deployment_type" == "three_network" ]; then
- sed -i 's/^.*storage_network:.*$/ storage_network:'" $private_subnet"'/' opnfv_ksgen_settings.yml
- else
- next_storage_ip=${interface_ip_arr[3]}
- storage_subnet=$(find_subnet $next_storage_ip $storage_subnet_mask)
- sed -i 's/^.*storage_network:.*$/ storage_network:'" $storage_subnet"'/' opnfv_ksgen_settings.yml
- fi
-
- ##replace public_subnet param
- public_subnet=$public_subnet'\'$public_short_subnet_mask
- sed -i 's/^.*public_subnet:.*$/ public_subnet:'" $public_subnet"'/' opnfv_ksgen_settings.yml
- if [ "$deployment_type" == "single_network" ]; then
- sed -i 's/^.*private_subnet:.*$/ private_subnet:'" $public_subnet"'/' opnfv_ksgen_settings.yml
- else
- ##replace private_subnet param
- private_subnet=$private_subnet'\'$private_short_subnet_mask
- sed -i 's/^.*private_subnet:.*$/ private_subnet:'" $private_subnet"'/' opnfv_ksgen_settings.yml
- fi
-
- ##replace public_dns param to be foreman server
- if [ "$deployment_type" == "single_network" ]; then
- sed -i 's/^.*public_dns:.*$/ public_dns: '${interface_ip_arr[0]}'/' opnfv_ksgen_settings.yml
- else
- sed -i 's/^.*public_dns:.*$/ public_dns: '${interface_ip_arr[2]}'/' opnfv_ksgen_settings.yml
- fi
-
- ##replace public_gateway
- if [ -z "$public_gateway" ]; then
- if [ "$deployment_type" == "single_network" ]; then
- public_gateway=$node_default_gw
- else
- ##if unset then we assume its the first IP in the public subnet
- public_subnet=$(find_subnet $next_public_ip $public_subnet_mask)
- public_gateway=$(increment_subnet $public_subnet 1)
- fi
- fi
- sed -i 's/^.*public_gateway:.*$/ public_gateway:'" $public_gateway"'/' opnfv_ksgen_settings.yml
-
- ##we have to define an allocation range of the public subnet to give
- ##to neutron to use as floating IPs
- ##if static ip range, then we take the difference of the end range and current ip
- ## to be the allocation pool
- ##if not static ip, we will use the last 20 IP from the subnet
- ## note that this is not a really good idea because the subnet must be at least a /27 for this to work...
- public_subnet=$(find_subnet $next_public_ip $public_subnet_mask)
- if [ ! -z "$static_ip_range" ]; then
- begin_octet=$(echo $next_public_ip | cut -d . -f4)
- end_octet=$(echo $static_ip_range_end | cut -d . -f4)
- ip_diff=$((end_octet-begin_octet))
- if [ $ip_diff -le 0 ]; then
- echo "${red}ip range left for floating range is less than or equal to 0! $ipdiff ${reset}"
- exit 1
- else
- public_allocation_start=$(next_ip $next_public_ip)
- public_allocation_end=$static_ip_range_end
- fi
- else
- last_ip_subnet=$(find_last_ip_subnet $next_public_ip $public_subnet_mask)
- public_allocation_start=$(subtract_ip $last_ip_subnet $floating_ip_count )
- public_allocation_end=${last_ip_subnet}
- fi
- echo "${blue}Neutron Floating IP range: $public_allocation_start to $public_allocation_end ${reset}"
-
- sed -i 's/^.*public_allocation_start:.*$/ public_allocation_start:'" $public_allocation_start"'/' opnfv_ksgen_settings.yml
- sed -i 's/^.*public_allocation_end:.*$/ public_allocation_end:'" $public_allocation_end"'/' opnfv_ksgen_settings.yml
-
- else
- printf '%s\n' 'deploy.sh: Unknown network type: $deployment_type' >&2
- exit 1
- fi
-
- echo "${blue}Parameters Complete. Settings have been set for Foreman. ${reset}"
-
- fi
-}
-
-##Configure bootstrap.sh to use the virtual Khaleesi playbook
-##params: none
-##usage: configure_virtual()
-configure_virtual() {
- if [ $virtual ]; then
- echo "${blue} Virtual flag detected, setting Khaleesi playbook to be opnfv-vm.yml ${reset}"
- sed -i 's/opnfv.yml/opnfv-vm.yml/' bootstrap.sh
- fi
-}
-
-##Starts Foreman VM with Vagrant
-##params: none
-##usage: start_vagrant()
-start_foreman() {
- echo "${blue}Starting Vagrant! ${reset}"
-
- ##stand up vagrant
- if ! vagrant up; then
- printf '%s\n' 'deploy.sh: Unable to complete Foreman VM install' >&2
- exit 1
- else
- echo "${blue}Foreman VM is up! ${reset}"
- fi
-}
-
-##start the VM if this is a virtual installation
-##this function does nothing if baremetal servers are being used
-##params: none
-##usage: start_virtual_nodes()
-start_virtual_nodes() {
- if [ $virtual ]; then
-
- ##Bring up VM nodes
- echo "${blue}Setting VMs up... ${reset}"
- nodes=`sed -nr '/nodes:/{:start /workaround/!{N;b start};//p}' opnfv_ksgen_settings.yml | sed -n '/^ [A-Za-z0-9]\+:$/p' | sed 's/\s*//g' | sed 's/://g'`
- ##due to ODL Helium bug of OVS connecting to ODL too early, we need controllers to install first
- ##this is fix kind of assumes more than I would like to, but for now it should be OK as we always have
- ##3 static controllers
- compute_nodes=`echo $nodes | tr " " "\n" | grep -v controller | tr "\n" " "`
- controller_nodes=`echo $nodes | tr " " "\n" | grep controller | tr "\n" " "`
- nodes=${controller_nodes}${compute_nodes}
- controller_count=0
- compute_wait_completed=false
-
- for node in ${nodes}; do
-
- ##remove VM nodes incase it wasn't cleaned up
- rm -rf $vm_dir/$node
- rm -rf /tmp/genesis/
-
- ##clone genesis and move into node folder
- clone_bgs $vm_dir/$node
-
- cd $vm_dir/$node
-
- if [ $base_config ]; then
- if ! cp -f $base_config opnfv_ksgen_settings.yml; then
- echo "${red}ERROR: Unable to copy $base_config to opnfv_ksgen_settings.yml${reset}"
- exit 1
- fi
- fi
-
- ##parse yaml into variables
- eval $(parse_yaml opnfv_ksgen_settings.yml "config_")
- ##find node type
- node_type=config_nodes_${node}_type
- node_type=$(eval echo \$$node_type)
-
- ##modify memory and cpu
- node_memory=$(eval echo \${config_nodes_${node}_memory})
- node_vcpus=$(eval echo \${config_nodes_${node}_cpus})
- node_storage=$(eval echo \${config_nodes_${node}_disk})
-
- sed -i 's/^.*vb.memory =.*$/ vb.memory = '"$node_memory"'/' Vagrantfile
- sed -i 's/^.*vb.cpus =.*$/ vb.cpus = '"$node_vcpus"'/' Vagrantfile
-
- if ! resize_vagrant_disk $node_storage; then
- echo "${red}Error while resizing vagrant box to size $node_storage for $node! ${reset}"
- exit 1
- fi
-
- ##trozet test make compute nodes wait 20 minutes
- if [ "$compute_wait_completed" = false ] && [ "$node_type" != "controller" ]; then
- echo "${blue}Waiting 20 minutes for Control nodes to install before continuing with Compute nodes..."
- compute_wait_completed=true
- sleep 1400
- fi
-
- ## Add Admin interface
- mac_string=config_nodes_${node}_mac_address
- mac_addr=$(eval echo \$$mac_string)
- mac_addr=$(echo $mac_addr | sed 's/:\|-//g')
- if [ $mac_addr == "" ]; then
- echo "${red} Unable to find mac_address for $node! ${reset}"
- exit 1
- fi
- this_admin_ip=${admin_ip_arr[$node]}
- sed -i 's/^.*eth_replace0.*$/ config.vm.network "private_network", virtualbox__intnet: "my_admin_network", ip: '\""$this_admin_ip"\"', netmask: '\""$admin_subnet_mask"\"', :mac => '\""$mac_addr"\"'/' Vagrantfile
-
- ## Add private interface
- if [ "$node_type" == "controller" ]; then
- mac_string=config_nodes_${node}_private_mac
- mac_addr=$(eval echo \$$mac_string)
- if [ $mac_addr == "" ]; then
- echo "${red} Unable to find private_mac for $node! ${reset}"
- exit 1
- fi
- else
- ##generate random mac
- mac_addr=$(echo -n 00-60-2F; dd bs=1 count=3 if=/dev/random 2>/dev/null |hexdump -v -e '/1 "-%02X"')
- fi
- mac_addr=$(echo $mac_addr | sed 's/:\|-//g')
- if [ "$node_type" == "controller" ]; then
- new_node_ip=${controllers_ip_arr[$controller_count]}
- if [ ! "$new_node_ip" ]; then
- echo "{red}ERROR: Empty node ip for controller $controller_count ${reset}"
- exit 1
- fi
- ((controller_count++))
- else
- next_private_ip=$(next_ip $next_private_ip)
- if [ ! "$next_private_ip" ]; then
- echo "{red}ERROR: Could not find private ip for $node ${reset}"
- exit 1
- fi
- new_node_ip=$next_private_ip
- fi
- sed -i 's/^.*eth_replace1.*$/ config.vm.network "private_network", virtualbox__intnet: "my_private_network", :mac => '\""$mac_addr"\"', ip: '\""$new_node_ip"\"', netmask: '\""$private_subnet_mask"\"'/' Vagrantfile
- ##replace host_ip in vm_nodes_provision with private ip
- sed -i 's/^host_ip=REPLACE/host_ip='$new_node_ip'/' vm_nodes_provision.sh
- ##replace ping site
- if [ ! -z "$ping_site" ]; then
- sed -i 's/www.google.com/'$ping_site'/' vm_nodes_provision.sh
- fi
-
- ##find public ip info and add public interface
- mac_addr=$(echo -n 00-60-2F; dd bs=1 count=3 if=/dev/random 2>/dev/null |hexdump -v -e '/1 "-%02X"')
- mac_addr=$(echo $mac_addr | sed 's/:\|-//g')
- this_public_ip=${public_ip_arr[$node]}
-
- if [ -z "$enable_virtual_dhcp" ]; then
- sed -i 's/^.*eth_replace2.*$/ config.vm.network "public_network", bridge: '\'"$public_interface"\'', :mac => '\""$mac_addr"\"', ip: '\""$this_public_ip"\"', netmask: '\""$public_subnet_mask"\"'/' Vagrantfile
- else
- sed -i 's/^.*eth_replace2.*$/ config.vm.network "public_network", bridge: '\'"$public_interface"\'', :mac => '\""$mac_addr"\"'/' Vagrantfile
- fi
- remove_vagrant_network eth_replace3
-
- ##modify provisioning to do puppet install, config, and foreman check-in
- ##substitute host_name and dns_server in the provisioning script
- host_string=config_nodes_${node}_short_name
- short_host_name=$(eval echo \$$host_string)
- ##substitute domain_name
- domain_name=$config_domain_name
- sed -i 's/^domain_name=REPLACE/domain_name='$domain_name'/' vm_nodes_provision.sh
- host_name=${short_host_name}.${domain_name}
- sed -i 's/^host_name=REPLACE/host_name='$host_name'/' vm_nodes_provision.sh
- ##dns server should be the foreman server
- sed -i 's/^dns_server=REPLACE/dns_server='${interface_ip_arr[0]}'/' vm_nodes_provision.sh
- ## remove bootstrap and NAT provisioning
- sed -i '/nat_setup.sh/d' Vagrantfile
- sed -i 's/bootstrap.sh/vm_nodes_provision.sh/' Vagrantfile
- ## modify default_gw to be node_default_gw
- sed -i 's/^.*default_gw =.*$/ default_gw = '\""$node_default_gw"\"'/' Vagrantfile
- echo "${blue}Starting Vagrant Node $node! ${reset}"
- ##stand up vagrant
- if ! vagrant up; then
- echo "${red} Unable to start $node ${reset}"
- exit 1
- else
- echo "${blue} $node VM is up! ${reset}"
- fi
- done
- echo "${blue} All VMs are UP! ${reset}"
- echo "${blue} Waiting for puppet to complete on the nodes... ${reset}"
- ##check puppet is complete
- ##ssh into foreman server, run check to verify puppet is complete
- pushd $vm_dir/foreman_vm
- if ! vagrant ssh -c "/opt/khaleesi/run.sh --no-logs --use /vagrant/opnfv_ksgen_settings.yml /opt/khaleesi/playbooks/validate_opnfv-vm.yml"; then
- echo "${red} Failed to validate puppet completion on nodes ${reset}"
- exit 1
- else
- echo "{$blue} Puppet complete on all nodes! ${reset}"
- fi
- popd
- ##add routes back to nodes
- for node in ${nodes}; do
- pushd $vm_dir/$node
- if ! vagrant ssh -c "route | grep default | grep $this_default_gw"; then
- echo "${blue} Adding public route back to $node! ${reset}"
- vagrant ssh -c "route add default gw $this_default_gw"
- vagrant ssh -c "route delete default gw 10.0.2.2"
- fi
- popd
- done
- if [ ! -z "$horizon_public_vip" ]; then
- echo "${blue} Virtual deployment SUCCESS!! Foreman URL: http://${foreman_ip}, Horizon URL: http://${horizon_public_vip} ${reset}"
- else
- ##Find public IP of controller
- for node in ${nodes}; do
- node_type=config_nodes_${node}_type
- node_type=$(eval echo \$$node_type)
- if [ "$node_type" == "controller" ]; then
- pushd $vm_dir/$node
- horizon_ip=`vagrant ssh -c "ifconfig enp0s10" | grep -Eo "inet [0-9\.]+" | awk {'print $2'}`
- popd
- break
- fi
- done
- if [ -z "$horizon_ip" ]; then
- echo "${red}Warn: Unable to determine horizon IP, please login to your controller node to find it${reset}"
- fi
- echo "${blue} Virtual deployment SUCCESS!! Foreman URL: http://${foreman_ip}, Horizon URL: http://${horizon_ip} ${reset}"
- fi
- fi
-}
-
-##check to make sure nodes are powered off
-##this function does nothing if virtual
-##params: none
-##usage: check_baremetal_nodes()
-check_baremetal_nodes() {
- if [ $virtual ]; then
- echo "${blue}Skipping Baremetal node power status check as deployment is virtual ${reset}"
- else
- echo "${blue}Checking Baremetal nodes power state... ${reset}"
- if [ ! -z "$base_config" ]; then
- # Install ipmitool
- # Major version is pinned to force some consistency for Arno
- if ! yum list installed | grep -i ipmitool; then
- echo "${blue}Installing ipmitool...${reset}"
- if ! yum -y install ipmitool-1*; then
- echo "${red}Failed to install ipmitool!${reset}"
- exit 1
- fi
- fi
-
- ###find all the bmc IPs and number of nodes
- node_counter=0
- output=`grep bmc_ip $base_config | grep -Eo '[0-9]+.[0-9]+.[0-9]+.[0-9]+'`
- for line in ${output} ; do
- bmc_ip[$node_counter]=$line
- ((node_counter++))
- done
-
- max_nodes=$((node_counter-1))
-
- ###find bmc_users per node
- node_counter=0
- output=`grep bmc_user $base_config | sed 's/\s*bmc_user:\s*//'`
- for line in ${output} ; do
- bmc_user[$node_counter]=$line
- ((node_counter++))
- done
-
- ###find bmc_pass per node
- node_counter=0
- output=`grep bmc_pass $base_config | sed 's/\s*bmc_pass:\s*//'`
- for line in ${output} ; do
- bmc_pass[$node_counter]=$line
- ((node_counter++))
- done
-
- for mynode in `seq 0 $max_nodes`; do
- echo "${blue}Node: ${bmc_ip[$mynode]} ${bmc_user[$mynode]} ${bmc_pass[$mynode]} ${reset}"
- ipmi_output=`ipmitool -I lanplus -P ${bmc_pass[$mynode]} -U ${bmc_user[$mynode]} -H ${bmc_ip[$mynode]} chassis status \
- | grep "System Power" | cut -d ':' -f2 | tr -d [:blank:]`
- if [ "$ipmi_output" == "on" ]; then
- echo "${red}Error: Node is powered on: ${bmc_ip[$mynode]} ${reset}"
- echo "${red}Please run clean.sh before running deploy! ${reset}"
- exit 1
- elif [ "$ipmi_output" == "off" ]; then
- echo "${blue}Node: ${bmc_ip[$mynode]} is powered off${reset}"
- else
- echo "${red}Warning: Unable to detect node power state: ${bmc_ip[$mynode]} ${reset}"
- fi
- done
- else
- echo "${red}base_config was not provided for a baremetal install! Exiting${reset}"
- exit 1
- fi
- fi
-}
-
-##resizes vagrant disk (cannot shrink)
-##params: size in GB
-##usage: resize_vagrant_disk 100
-resize_vagrant_disk() {
- if [[ "$1" < 40 ]]; then
- echo "${blue}Warn: Requested disk size cannot be less than 40, using 40 as new size${reset}"
- new_size_gb=40
- else
- new_size_gb=$1
- fi
-
- if ! vagrant box list | grep opnfv; then
- vagrant box remove -f opnfv/centos-7.0
- if ! vagrant box add opnfv/centos-7.0 --provider virtualbox; then
- echo "${red}Unable to reclone vagrant box! Exiting...${reset}"
- exit 1
- fi
- fi
-
- pushd $vagrant_box_dir
-
- # Close medium to make sure we can modify it
- vboxmanage closemedium disk $vagrant_box_vmdk
-
- cur_size=$(vboxmanage showhdinfo $vagrant_box_vmdk | grep -i capacity | grep -Eo [0-9]+)
- cur_size_gb=$((cur_size / 1024))
-
- if [ "$cur_size_gb" -eq "$new_size_gb" ]; then
- echo "${blue}Info: Disk size already ${cur_size_gb} ${reset}"
- popd
- return
- elif [[ "$new_size_gb" < "$cur_size_gb" ]] ; then
- echo "${blue}Info: Requested disk is less than ${cur_size_gb} ${reset}"
- echo "${blue}Re-adding vagrant box${reset}"
- if vagrant box list | grep opnfv; then
- popd
- vagrant box remove -f opnfv/centos-7.0
- if ! vagrant box add opnfv/centos-7.0 --provider virtualbox; then
- echo "${red}Unable to reclone vagrant box! Exiting...${reset}"
- exit 1
- fi
- pushd $vagrant_box_dir
- fi
- fi
-
- new_size=$((new_size_gb * 1024))
- if ! vboxmanage clonehd $vagrant_box_vmdk tmp-disk.vdi --format vdi; then
- echo "${red}Error: Unable to clone ${vagrant_box_vmdk}${reset}"
- popd
- return 1
- fi
-
- if ! vboxmanage modifyhd tmp-disk.vdi --resize $new_size; then
- echo "${red}Error: Unable modify tmp-disk.vdi to ${new_size}${reset}"
- popd
- return 1
- fi
-
- if ! vboxmanage clonehd tmp-disk.vdi resized-disk.vmdk --format vmdk; then
- echo "${red}Error: Unable clone tmp-disk.vdi to vmdk${reset}"
- popd
- return 1
- fi
-
- vboxmanage closemedium disk tmp-disk.vdi --delete
- rm -f tmp-disk.vdi $vagrant_box_vmdk
- cp -f resized-disk.vmdk $vagrant_box_vmdk
- vboxmanage closemedium disk resized-disk.vmdk --delete
- popd
-}
-
-##END FUNCTIONS
-
-main() {
- parse_cmdline "$@"
- disable_selinux
- check_baremetal_nodes
- install_EPEL
- install_vbox
- install_ansible
- install_vagrant
- clean_tmp
- verify_vm_dir
- clone_bgs $vm_dir/foreman_vm
- configure_network
- configure_virtual
- start_foreman
- start_virtual_nodes
-}
-
-main "$@"
Code Review / genesis.git / blobdiff