X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2Fatngw100.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2Fatngw100.h;h=9c81e3199f916d49d498d6ce3c5a7bd68ec95aec;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/include/configs/atngw100.h b/qemu/roms/u-boot/include/configs/atngw100.h
new file mode 100644
index 000000000..9c81e3199
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/atngw100.h
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2006 Atmel Corporation
+ *
+ * Configuration settings for the AVR32 Network Gateway
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/hardware.h>
+
+#define CONFIG_AT32AP
+#define CONFIG_AT32AP7000
+#define CONFIG_ATNGW100
+
+/*
+ * Set up the PLL to run at 140 MHz, the CPU to run at the PLL
+ * frequency, the HSB and PBB busses to run at 1/2 the PLL frequency
+ * and the PBA bus to run at 1/4 the PLL frequency.
+ */
+#define CONFIG_PLL
+#define CONFIG_SYS_POWER_MANAGER
+#define CONFIG_SYS_OSC0_HZ			20000000
+#define CONFIG_SYS_PLL0_DIV			1
+#define CONFIG_SYS_PLL0_MUL			7
+#define CONFIG_SYS_PLL0_SUPPRESS_CYCLES	16
+#define CONFIG_SYS_CLKDIV_CPU			0
+#define CONFIG_SYS_CLKDIV_HSB			1
+#define CONFIG_SYS_CLKDIV_PBA			2
+#define CONFIG_SYS_CLKDIV_PBB			1
+
+/* Reserve VM regions for SDRAM and NOR flash */
+#define CONFIG_SYS_NR_VM_REGIONS		2
+
+/*
+ * The PLLOPT register controls the PLL like this:
+ *   icp = PLLOPT<2>
+ *   ivco = PLLOPT<1:0>
+ *
+ * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz).
+ */
+#define CONFIG_SYS_PLL0_OPT			0x04
+
+#define CONFIG_USART_BASE		ATMEL_BASE_USART1
+#define CONFIG_USART_ID			1
+/* User serviceable stuff */
+#define CONFIG_DOS_PARTITION
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_STACKSIZE		(2048)
+
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_BOOTARGS							\
+	"console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2"
+#define CONFIG_BOOTCOMMAND						\
+	"fsload; bootm"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_AUTOBOOT
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT		\
+	"Press SPACE to abort autoboot in %d seconds\n", bootdelay
+#define CONFIG_AUTOBOOT_DELAY_STR	"d"
+#define CONFIG_AUTOBOOT_STOP_STR	" "
+
+/*
+ * After booting the board for the first time, new ethernet addresses
+ * should be generated and assigned to the environment variables
+ * "ethaddr" and "eth1addr". This is normally done during production.
+ */
+#define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+/*
+ * BOOTP/DHCP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_SPI
+
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_SETGETDCR
+#undef CONFIG_CMD_SOURCE
+#undef CONFIG_CMD_XIMG
+
+#define CONFIG_ATMEL_USART
+#define CONFIG_MACB
+#define CONFIG_PORTMUX_PIO
+#define CONFIG_SYS_NR_PIOS			5
+#define CONFIG_SYS_HSDRAMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_ATMEL_MCI
+#define CONFIG_GENERIC_MMC
+#define CONFIG_ATMEL_SPI
+
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_ATMEL
+
+#define CONFIG_SYS_DCACHE_LINESZ		32
+#define CONFIG_SYS_ICACHE_LINESZ		32
+
+#define CONFIG_NR_DRAM_BANKS		1
+
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+
+#define CONFIG_SYS_FLASH_BASE			0x00000000
+#define CONFIG_SYS_FLASH_SIZE			0x800000
+#define CONFIG_SYS_MAX_FLASH_BANKS		1
+#define CONFIG_SYS_MAX_FLASH_SECT		135
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_TEXT_BASE		0x00000000
+
+#define CONFIG_SYS_INTRAM_BASE			INTERNAL_SRAM_BASE
+#define CONFIG_SYS_INTRAM_SIZE			INTERNAL_SRAM_SIZE
+#define CONFIG_SYS_SDRAM_BASE			EBI_SDRAM_BASE
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SIZE			65536
+#define CONFIG_ENV_ADDR			(CONFIG_SYS_FLASH_BASE + CONFIG_SYS_FLASH_SIZE - CONFIG_ENV_SIZE)
+
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INTRAM_BASE + CONFIG_SYS_INTRAM_SIZE)
+
+#define CONFIG_SYS_MALLOC_LEN			(256*1024)
+#define CONFIG_SYS_DMA_ALLOC_LEN		(16384)
+
+/* Allow 4MB for the kernel run-time image */
+#define CONFIG_SYS_LOAD_ADDR			(EBI_SDRAM_BASE + 0x00400000)
+#define CONFIG_SYS_BOOTPARAMS_LEN		(16 * 1024)
+
+/* Other configuration settings that shouldn't have to change all that often */
+#define CONFIG_SYS_PROMPT			"U-Boot> "
+#define CONFIG_SYS_CBSIZE			256
+#define CONFIG_SYS_MAXARGS			16
+#define CONFIG_SYS_PBSIZE			(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_LONGHELP
+
+#define CONFIG_SYS_MEMTEST_START		EBI_SDRAM_BASE
+#define CONFIG_SYS_MEMTEST_END			(CONFIG_SYS_MEMTEST_START + 0x1f00000)
+
+#define CONFIG_SYS_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 }
+
+#endif /* __CONFIG_H */