X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2Fatc.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2Fatc.h;h=77fa79a185de93639c177d57ab28a1df3556fb71;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/atc.h b/qemu/roms/u-boot/include/configs/atc.h new file mode 100644 index 000000000..77fa79a18 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/atc.h @@ -0,0 +1,489 @@ +/* + * (C) Copyright 2001 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_ATC 1 /* ...on a ATC board */ +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_SYS_TEXT_BASE 0xFF000000 + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#define CONFIG_CONS_ON_SMC /* define if console on SMC */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else*/ +#define CONFIG_CONS_INDEX 2 /* which serial channel for console */ + +#define CONFIG_BAUDRATE 115200 + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_ON_FCC + +#define CONFIG_ETHER_ON_FCC2 + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - RAM for BD/Buffers is on the 60x Bus (see 28-13) + * - Enable Full Duplex in FSMR + */ +# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14) +# define CONFIG_SYS_CPMFCR_RAMTYPE 0 +# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) + +#define CONFIG_ETHER_ON_FCC3 + +/* + * - Rx-CLK is CLK15 + * - Tx-CLK is CLK16 + * - RAM for BD/Buffers is on the local Bus (see 28-13) + * - Enable Half Duplex in FSMR + */ +# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16) + +/* system clock rate (CLKIN) - equal to the 60x and local bus speed */ +#define CONFIG_8260_CLKIN 64000000 /* in Hz */ + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in Hz */ + +#define CONFIG_PREBOOT \ + "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;"\ + "echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"\ + "bootm" + +/*----------------------------------------------------------------------- + * Miscellaneous configuration options + */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PCMCIA +#define CONFIG_CMD_DATE +#define CONFIG_CMD_IDE + + +#define CONFIG_DOS_PARTITION + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_PIO_MODE 0 /* IDE interface in PIO Mode 0 */ + +#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100 /* "bad" address */ + +#define CONFIG_SYS_ALLOC_DPRAM + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SPI + +#define CONFIG_RTC_DS12887 + +#define RTC_BASE_ADDR 0xF5000000 +#define RTC_PORT_ADDR RTC_BASE_ADDR + 0x800 +#define RTC_PORT_DATA RTC_BASE_ADDR + 0x808 + +#define CONFIG_MISC_INIT_R + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * Flash configuration + */ + +#define CONFIG_SYS_FLASH_BASE 0xFF000000 +#define CONFIG_SYS_FLASH_SIZE 0x00800000 + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +#define CONFIG_FLASH_16BIT + +/*----------------------------------------------------------------------- + * Hard Reset Configuration Words + * + * if you change bits in the HRCW, you must also change the CONFIG_SYS_* + * defines for the various registers affected by the HRCW e.g. changing + * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR. + */ +#define CONFIG_SYS_HRCW_MASTER (HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \ + HRCW_BPS10 |\ + HRCW_APPC10) + +/* no slaves so just fill with zeros */ +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 + +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CONFIG_SYS_IMMR 0xF0000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + * + * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE. + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc()*/ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP +#define CONFIG_SYS_PCI_MSTR_IO_BUS 0x00000000 /* PCI base */ + +#if 1 +/* environment is in Flash */ +#define CONFIG_ENV_IS_IN_FLASH 1 +# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+0x30000) +# define CONFIG_ENV_SIZE 0x10000 +# define CONFIG_ENV_SECT_SIZE 0x10000 +#else +#define CONFIG_ENV_IS_IN_EEPROM 1 +#define CONFIG_ENV_OFFSET 0 +#define CONFIG_ENV_SIZE 2048 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */ +#endif + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +#define CONFIG_SYS_HID0_INIT (HID0_ICE|HID0_DCE|HID0_ICFI|\ + HID0_DCI|HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID0_FINAL (HID0_IFEM|HID0_ABE) +#define CONFIG_SYS_HID2 0 + +/*----------------------------------------------------------------------- + * RMR - Reset Mode Register 5-5 + *----------------------------------------------------------------------- + * turn on Checkstop Reset Enable + */ +#define CONFIG_SYS_RMR RMR_CSRE + +/*----------------------------------------------------------------------- + * BCR - Bus Configuration 4-25 + *----------------------------------------------------------------------- + */ +#define BCR_APD01 0x10000000 +#define CONFIG_SYS_BCR (BCR_APD01|BCR_ETM|BCR_LETM) /* 8260 mode */ + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 4-31 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_SIUMCR (SIUMCR_BBD|SIUMCR_APPC10|\ + SIUMCR_CS10PC00|SIUMCR_BCTLC10) + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ + +/*----------------------------------------------------------------------- + * TMCNTSC - Time Counter Status and Control 4-40 + *----------------------------------------------------------------------- + * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, + * and enable Time Counter + */ +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 4-42 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable + * Periodic timer + */ +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) + +/*----------------------------------------------------------------------- + * SCCR - System Clock Control 9-8 + *----------------------------------------------------------------------- + * Ensure DFBRG is Divide by 16 + */ +#define CONFIG_SYS_SCCR SCCR_DFBRG01 + +/*----------------------------------------------------------------------- + * RCCR - RISC Controller Configuration 13-7 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_RCCR 0 + +#define CONFIG_SYS_MIN_AM_MASK 0xC0000000 +/*----------------------------------------------------------------------- + * MPTPR - Memory Refresh Timer Prescaler Register 10-18 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_MPTPR 0x1F00 + +/*----------------------------------------------------------------------- + * PSRT - Refresh Timer Register 10-16 + *----------------------------------------------------------------------- + */ +#define CONFIG_SYS_PSRT 0x0f + +/*----------------------------------------------------------------------- + * PSRT - SDRAM Mode Register 10-10 + *----------------------------------------------------------------------- + */ + + /* SDRAM initialization values for 8-column chips + */ +#define CONFIG_SYS_OR2_8COL (CONFIG_SYS_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A7 |\ + ORxS_NUMR_12) + +#define CONFIG_SYS_PSDMR_8COL (PSDMR_PBI |\ + PSDMR_SDAM_A15_IS_A5 |\ + PSDMR_BSMA_A15_A17 |\ + PSDMR_SDA10_PBI1_A7 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + + /* SDRAM initialization values for 9-column chips + */ +#define CONFIG_SYS_OR2_9COL (CONFIG_SYS_MIN_AM_MASK |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A6 |\ + ORxS_NUMR_12) + +#define CONFIG_SYS_PSDMR_9COL (PSDMR_PBI |\ + PSDMR_SDAM_A16_IS_A5 |\ + PSDMR_BSMA_A15_A17 |\ + PSDMR_SDA10_PBI1_A6 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) + +/* + * Init Memory Controller: + * + * Bank Bus Machine PortSz Device + * ---- --- ------- ------ ------ + * 0 60x GPCM 8 bit Boot ROM + * 1 60x GPCM 64 bit FLASH + * 2 60x SDRAM 64 bit SDRAM + * + */ + +#define CONFIG_SYS_MRS_OFFS 0x00000000 + +/* Bank 0 - FLASH + */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ + BRx_PS_16 |\ + BRx_MS_GPCM_P |\ + BRx_V) + +#define CONFIG_SYS_OR0_PRELIM (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE) |\ + ORxG_CSNT |\ + ORxG_ACS_DIV1 |\ + ORxG_SCY_3_CLK |\ + ORxU_EHTR_8IDLE) + + +/* Bank 2 - 60x bus SDRAM + */ +#ifndef CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CONFIG_SYS_OR2_PRELIM CONFIG_SYS_OR2_8COL + +#define CONFIG_SYS_PSDMR CONFIG_SYS_PSDMR_8COL +#endif /* CONFIG_SYS_RAMBOOT */ + +#define CONFIG_SYS_BR4_PRELIM ((RTC_BASE_ADDR & BRx_BA_MSK) |\ + BRx_PS_8 |\ + BRx_MS_UPMA |\ + BRx_V) + +#define CONFIG_SYS_OR4_PRELIM (ORxU_AM_MSK | ORxU_BI) + +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + * + */ +#define CONFIG_I82365 + +#define CONFIG_SYS_PCMCIA_MEM_ADDR 0x81000000 +#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x1000 + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */ +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR 0xa0000000 + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET 0x100 + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET 0x100 + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET 0x108 + +#endif /* __CONFIG_H */