X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FTQM834x.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FTQM834x.h;h=6762e3a57e2c71587ac4b2ded949cdfe06d25fab;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/TQM834x.h b/qemu/roms/u-boot/include/configs/TQM834x.h new file mode 100644 index 000000000..6762e3a57 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/TQM834x.h @@ -0,0 +1,574 @@ +/* + * (C) Copyright 2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * TQM8349 board configuration file + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 Family */ +#define CONFIG_MPC834x 1 /* MPC834x specific */ +#define CONFIG_MPC8349 1 /* MPC8349 specific */ +#define CONFIG_TQM834X 1 /* TQM834X board specific */ + +#define CONFIG_SYS_TEXT_BASE 0x80000000 + +/* IMMR Base Address Register, use Freescale default: 0xff400000 */ +#define CONFIG_SYS_IMMR 0xff400000 + +/* System clock. Primary input clock when in PCI host mode */ +#define CONFIG_83XX_CLKIN 66666000 /* 66,666 MHz */ + +/* + * Local Bus LCRR + * LCRR: DLL bypass, Clock divider is 8 + * + * for CSB = 266 MHz it gives LCB clock frequency = 33 MHz + * + * External Local Bus rate is + * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_8 + +/* board pre init: do not call, nothing to do */ +#undef CONFIG_BOARD_EARLY_INIT_F + +/* detect the number of flash banks */ +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * DDR Setup + */ + /* DDR is system memory*/ +#define CONFIG_SYS_DDR_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define DDR_CASLAT_25 /* CASLAT set to 2.5 */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup */ + +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00100000 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_BASE 0x80000000 /* start of FLASH */ +#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size in MB */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sectors */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + +/* + * FLASH bank number detection + */ + +/* + * When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, the actual number of + * Flash banks has to be determined at runtime and stored in a gloabl variable + * tqm834x_num_flash_banks. The value of CONFIG_SYS_MAX_FLASH_BANKS_DETECT is + * only used instead of CONFIG_SYS_MAX_FLASH_BANKS to allocate the array + * flash_info, and should be made sufficiently large to accomodate the number + * of banks that might actually be detected. Since most (all?) Flash related + * functions use CONFIG_SYS_MAX_FLASH_BANKS as the number of actual banks on + * the board, it is defined as tqm834x_num_flash_banks. + */ +#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 2 + +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max sectors per device */ + +/* 32 bit device at 0x80000000 via GPCM (0x8000_1801) */ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BR_BA) \ + | BR_MS_GPCM \ + | BR_PS_32 \ + | BR_V) + +/* FLASH timing (0x0000_0c54) */ +#define CONFIG_SYS_OR_TIMING_FLASH (OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV4 \ + | OR_GPCM_SCY_5 \ + | OR_GPCM_TRLX) + +#define CONFIG_SYS_PRELIM_OR_AM OR_AM_1GB /* OR addr mask: 1 GiB */ + +#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \ + | CONFIG_SYS_OR_TIMING_FLASH) + +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_1GB) + + /* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE + +/* disable remaining mappings */ +#define CONFIG_SYS_BR1_PRELIM 0x00000000 +#define CONFIG_SYS_OR1_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWBAR1_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWAR1_PRELIM 0x00000000 + +#define CONFIG_SYS_BR2_PRELIM 0x00000000 +#define CONFIG_SYS_OR2_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWBAR2_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWAR2_PRELIM 0x00000000 + +#define CONFIG_SYS_BR3_PRELIM 0x00000000 +#define CONFIG_SYS_OR3_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWBAR3_PRELIM 0x00000000 +#define CONFIG_SYS_LBLAWAR3_PRELIM 0x00000000 + +/* + * Monitor config + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT +#else +# undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + + /* Reserve 384 kB = 3 sect. for Mon */ +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) + /* Reserve 512 kB for malloc */ +#define CONFIG_SYS_MALLOC_LEN (512 * 1024) + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 + +/* I2C EEPROM, configuration for onboard EEPROMs 24C256 and 24C32 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* 16 bit */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32 bytes/write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10ms +/- 20% */ +#define CONFIG_SYS_I2C_MULTI_EEPROMS /* more than one eeprom */ + +/* I2C RTC */ +#define CONFIG_RTC_DS1337 /* use ds1337 rtc via i2c */ +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */ + +/* I2C SYSMON (LM75) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 + +/* + * TSEC + */ +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_MII + +#define CONFIG_SYS_TSEC1_OFFSET 0x24000 +#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) +#define CONFIG_SYS_TSEC2_OFFSET 0x25000 +#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET) + +#if defined(CONFIG_TSEC_ENET) + +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 1 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_PCI + +#if defined(CONFIG_PCI) + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ + +/* PCI1 host bridge */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE \ + (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE) +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#undef CONFIG_EEPRO100 +#define CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR CONFIG_SYS_PCI1_IO_BASE + #define PCI_ENET0_MEMADDR CONFIG_SYS_PCI1_MEM_BASE + #define PCI_IDSEL_NUMBER 0x1c /* slot0 (IDSEL) = 28 */ +#endif + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + +/* + * Environment + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR \ + (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ +#define CONFIG_ENV_SIZE 0x8000 /* 32K max size */ +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DTT +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_NFS +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP + +#if defined(CONFIG_PCI) + #define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_SYS_RAMBOOT) + #undef CONFIG_CMD_SAVEENV + #undef CONFIG_CMD_LOADS +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ + +#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */ + +#if defined(CONFIG_CMD_KGDB) + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + + /* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ + /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) + +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN_4X1 |\ + HRCWL_VCO_1X2 |\ + HRCWL_CORE_TO_CSB_2X1) + +#if defined(PCI_64BIT) +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_64_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII) +#else +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_32_BIT_PCI |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCI2_ARBITER_DISABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_TSEC1M_IN_GMII |\ + HRCWH_TSEC2M_IN_GMII) +#endif + +/* System IO Config */ +#define CONFIG_SYS_SICRH 0 +#define CONFIG_SYS_SICRL SICRL_LDP_A + +/* i-cache and d-cache disabled */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (CONFIG_SYS_HID0_INIT | \ + HID0_ENABLE_INSTRUCTION_CACHE) +#define CONFIG_SYS_HID2 HID2_HBE + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR 0 - 512M */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_SDRAM_BASE + 0x10000000 \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_SDRAM_BASE + 0x10000000 \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +/* stack in DCACHE @ 512M (no backing mem) */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_INIT_RAM_ADDR \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_INIT_RAM_ADDR \ + | BATU_BL_128K \ + | BATU_VS \ + | BATU_VP) + +/* PCI */ +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI1_MEM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI1_MEM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI1_MMIO_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PCI1_IO_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PCI1_IO_BASE \ + | BATU_BL_16M \ + | BATU_VS \ + | BATU_VP) +#else +#define CONFIG_SYS_IBAT3L (0) +#define CONFIG_SYS_IBAT3U (0) +#define CONFIG_SYS_IBAT4L (0) +#define CONFIG_SYS_IBAT4U (0) +#define CONFIG_SYS_IBAT5L (0) +#define CONFIG_SYS_IBAT5U (0) +#endif + +/* IMMRBAR */ +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_IMMR \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT6U (CONFIG_SYS_IMMR \ + | BATU_BL_1M \ + | BATU_VS \ + | BATU_VP) + +/* FLASH */ +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_FLASH_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT7U (CONFIG_SYS_FLASH_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) + +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U +#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ + + /* default location for tftp and bootm */ +#define CONFIG_LOADADDR 400000 + +#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=tqm834x\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addcons=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0" \ + "flash_nfs_old=run nfsargs addip addcons;" \ + "bootm ${kernel_addr}\0" \ + "flash_nfs=run nfsargs addip addcons;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "flash_self_old=run ramargs addip addcons;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "net_nfs_old=tftp 400000 ${bootfile};" \ + "run nfsargs addip addcons;bootm\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addcons; " \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "bootfile=tqm834x/uImage\0" \ + "fdtfile=tqm834x/tqm834x.dtb\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=600000\0" \ + "ramdisk_addr_r=800000\0" \ + "kernel_addr=800C0000\0" \ + "fdt_addr=800A0000\0" \ + "ramdisk_addr=80300000\0" \ + "u-boot=tqm834x/u-boot.bin\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "update=protect off 80000000 +${filesize};" \ + "era 80000000 +${filesize};" \ + "cp.b 200000 80000000 ${filesize}\0" \ + "upd=run load update\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * JFFS2 partitions + */ +/* mtdparts command line support */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=TQM834x-0" + +/* default mtd partition table */ +#define MTDPARTS_DEFAULT "mtdparts=TQM834x-0:256k(u-boot),256k(env)," \ + "1m(kernel),2m(initrd)," \ + "-(user);" \ + +#endif /* __CONFIG_H */