X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FPCI405.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FPCI405.h;h=0989407fc7db8093204d6b25516bfdb4080f85fe;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/PCI405.h b/qemu/roms/u-boot/include/configs/PCI405.h new file mode 100644 index 000000000..0989407fc --- /dev/null +++ b/qemu/roms/u-boot/include/configs/PCI405.h @@ -0,0 +1,294 @@ +/* + * (C) Copyright 2007 + * Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com + * + * (C) Copyright 2001-2004 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_405GP 1 /* This is a PPC405 CPU */ +#define CONFIG_PCI405 1 /* ...on a PCI405 board */ + +#define CONFIG_SYS_TEXT_BASE 0xFFFD0000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */ + +#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */ + +#define CONFIG_BOARD_TYPES 1 /* support board types */ + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTDELAY 0 /* autoboot after 0 seconds */ + +#undef CONFIG_BOOTARGS +#define CONFIG_EXTRA_ENV_SETTINGS \ + "mem_linux=14336k\0" \ + "optargs=panic=0\0" \ + "ramargs=setenv bootargs mem=$mem_linux root=/dev/ram rw\0" \ + "addcons=setenv bootargs $bootargs console=ttyS0,$baudrate $optargs\0" \ + "" +#define CONFIG_BOOTCOMMAND "run ramargs;run addcons;loadpci" + +#define CONFIG_PREBOOT /* enable preboot variable */ + +/* + * Command line configuration. + */ +#include + +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_ITEST +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +#define CONFIG_CMD_PCI +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_BSP +#define CONFIG_CMD_EEPROM + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ + +#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */ + +/* + * Miscellaneous configurable options + */ + +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */ + +#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ + +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CONFIG_CONS_INDEX 1 /* Use UART0 */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_serial_clock() + +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */ +#define CONFIG_SYS_BASE_BAUD 691200 + +/* The following table includes the supported baudrates */ +#define CONFIG_SYS_BAUDRATE_TABLE \ + { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \ + 57600, 115200, 230400, 460800, 921600 } + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#undef CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */ +#define PCI_HOST_FORCE 1 /* configure as pci host */ +#define PCI_HOST_AUTO 2 /* detected via arbiter enable */ + +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci host function */ +#undef CONFIG_PCI_PNP /* no pci plug-and-play */ + /* resource configuration */ + +#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */ + +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0407 /* PCI Device ID: PCI-405 */ +#define CONFIG_SYS_PCI_CLASSCODE 0x0280 /* PCI Class Code: Network/Other*/ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ + +#define CONFIG_SYS_PCI_PTM2LA 0xef600000 /* point to internal regs */ +#define CONFIG_SYS_PCI_PTM2MS 0xffe00001 /* 2MB, enable */ +#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 + */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFFD0000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ + +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */ +#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */ +#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */ +/* + * The following defines are added for buggy IOP480 byte interface. + * All other boards should use the standard values (CPCI405 etc.) + */ +#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */ +#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */ +#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */ + +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */ +#define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars*/ + /* total size of a CAT24WC08 is 1024 bytes */ + +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ + +/*----------------------------------------------------------------------- + * I2C EEPROM (CAT24WC16) for environment + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_PPC4XX +#define CONFIG_SYS_I2C_PPC4XX_CH0 +#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000 +#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +/* mask of address bits that overflow into the "EEPROM chip address" */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */ + /* 16 byte page write mode using*/ + /* last 4 bits of the address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */ + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + */ + +/* Memory Bank 0 (Flash Bank 0) initialization */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */ + +/* Memory Bank 1 (NVRAM/RTC) initialization */ +#define CONFIG_SYS_EBC_PB1AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */ +#define CONFIG_SYS_EBC_PB1CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 2 (CAN0, 1) initialization */ +#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +/*#define CONFIG_SYS_EBC_PB2AP 0x038056C0 / * BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ + +/* Memory Bank 3 (FPGA internal) initialization */ +#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */ +#define CONFIG_SYS_EBC_PB3CR 0xF041C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */ +#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000 + +/*----------------------------------------------------------------------- + * FPGA stuff + */ +/* FPGA internal regs */ +#define CONFIG_SYS_FPGA_MODE 0x00 +#define CONFIG_SYS_FPGA_STATUS 0x02 +#define CONFIG_SYS_FPGA_TS 0x04 +#define CONFIG_SYS_FPGA_TS_LOW 0x06 +#define CONFIG_SYS_FPGA_TS_CAP0 0x10 +#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12 +#define CONFIG_SYS_FPGA_TS_CAP1 0x14 +#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16 +#define CONFIG_SYS_FPGA_TS_CAP2 0x18 +#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a +#define CONFIG_SYS_FPGA_TS_CAP3 0x1c +#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e + +/* FPGA Mode Reg */ +#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001 +#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100 +#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000 +#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000 + +/* FPGA Status Reg */ +#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001 +#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002 +#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004 +#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008 +#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000 + +#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */ +#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */ + +/* FPGA program pin configuration */ +#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */ +#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */ +#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */ +#define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */ +/* new INIT and DONE pins since board revision 1.2 (for PPC405GPr support) */ +#define CONFIG_SYS_FPGA_INIT_V12 0x00008000 /* FPGA init pin (ppc input) */ +#define CONFIG_SYS_FPGA_DONE_V12 0x00010000 /* FPGA done pin (ppc input) */ + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory ( OCM ) for temperary stack until sdram is tested */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +/* On Chip Memory location */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#endif /* __CONFIG_H */