X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FP1_P2_RDB.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FP1_P2_RDB.h;h=0f04067258385d1007710f64f3cb3a89ea0d4c29;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/include/configs/P1_P2_RDB.h b/qemu/roms/u-boot/include/configs/P1_P2_RDB.h
new file mode 100644
index 000000000..0f0406725
--- /dev/null
+++ b/qemu/roms/u-boot/include/configs/P1_P2_RDB.h
@@ -0,0 +1,711 @@
+/*
+ * Copyright 2009-2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/*
+ * P1 P2 RDB board configuration file
+ * This file is intended to address a set of Low End and Ultra Low End
+ * Freescale SOCs of QorIQ series(RDB platforms).
+ * Currently only P2020RDB
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#ifdef CONFIG_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
+#ifdef CONFIG_P1011RDB
+#define CONFIG_P1011
+#endif
+#ifdef CONFIG_P1020RDB
+#define CONFIG_P1020
+#endif
+#ifdef CONFIG_P2010RDB
+#define CONFIG_P2010
+#endif
+#ifdef CONFIG_P2020RDB
+#define CONFIG_P2020
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_U_BOOT		1
+#define CONFIG_RAMBOOT_NAND		1
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
+#else
+#define CONFIG_SYS_LDSCRIPT $(CPUDIR)/u-boot-nand.lds
+#define CONFIG_SYS_TEXT_BASE		0xf8f82000
+#endif /* CONFIG_NAND_SPL */
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RAMBOOT_SDCARD		1
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RAMBOOT_SPIFLASH		1
+#define CONFIG_SYS_TEXT_BASE		0x11000000
+#define CONFIG_RESET_VECTOR_ADDRESS	0x110bfffc
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE		0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE		1	/* BOOKE */
+#define CONFIG_E500		1	/* BOOKE e500 family */
+#define CONFIG_FSL_ELBC		1	/* Enable eLBC Support */
+
+#define CONFIG_PCI		1	/* Enable PCI/PCIE */
+#if defined(CONFIG_PCI)
+#define CONFIG_PCIE1		1	/* PCIE controler 1 (slot 1) */
+#define CONFIG_PCIE2		1	/* PCIE controler 2 (slot 2) */
+#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
+#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
+#define CONFIG_FSL_PCIE_RESET	1	/* need PCIe reset errata */
+#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
+#endif /* #if defined(CONFIG_PCI) */
+#define CONFIG_FSL_LAW		1	/* Use common FSL init code */
+#define CONFIG_TSEC_ENET		/* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#if defined(CONFIG_PCI)
+#define CONFIG_E1000		1	/*  E1000 pci Ethernet card*/
+#endif
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
+#define CONFIG_DDR_CLK_FREQ	66666666 /* DDRCLK on P1_P2 RDB */
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /*sysclk for P1_P2 RDB */
+
+#if defined(CONFIG_P2020) || defined(CONFIG_P1020)
+#define CONFIG_MP
+#endif
+
+#define CONFIG_HWCONFIG
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE			/* toggle L2 cache */
+#define CONFIG_BTB			/* toggle branch predition */
+
+#define CONFIG_ADDR_STREAMING		/* toggle addr streaming */
+
+#define CONFIG_ENABLE_36BIT_PHYS	1
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP			1
+#define CONFIG_SYS_NUM_ADDR_MAP		16	/* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x1fffffff
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+ /*
+  * Config the L2 Cache as L2 SRAM
+  */
+#define CONFIG_SYS_INIT_L2_ADDR		0xf8f80000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS	0xff8f80000ull
+#else
+#define CONFIG_SYS_INIT_L2_ADDR_PHYS	CONFIG_SYS_INIT_L2_ADDR
+#endif
+#define CONFIG_SYS_L2_SIZE		(512 << 10)
+#define CONFIG_SYS_INIT_L2_END		(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
+
+#define CONFIG_SYS_CCSRBAR		0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
+
+#if defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#endif
+
+/* DDR Setup */
+#define CONFIG_SYS_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
+
+#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
+
+#define CONFIG_SYS_SDRAM_SIZE	1024 	/* DDR size on P1_P2 RDBs */
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_NUM_DDR_CONTROLLERS	1
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	1
+
+#define CONFIG_SYS_DDR_ERR_INT_EN	0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
+#define CONFIG_SYS_DDR_SBE		0x00FF0000
+
+/*
+ * Memory map
+ *
+ * 0x0000_0000	0x3fff_ffff	DDR			1G cacheablen
+ * 0x8000_0000  0xbfff_ffff	PCI Express Mem		1G non-cacheable
+ * 0xffc0_0000  0xffc3_ffff	PCI IO range		256k non-cacheable
+ *
+ * Localbus cacheable (TBD)
+ * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
+ *
+ * Localbus non-cacheable
+ * 0xef00_0000	0xefff_ffff	FLASH			16M non-cacheable
+ * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
+ * 0xffb0_0000	0xffbf_ffff	VSC7385 switch		1M non-cacheable
+ * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
+ * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
+ */
+
+/*
+ * Local Bus Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE		0xef000000	/* start of FLASH 16M */
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	0xfef000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_FLASH_BR_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+					BR_PS_16 | BR_V)
+#define CONFIG_FLASH_OR_PRELIM		0xff000ff7
+
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	128	/* sectors per device */
+#undef	CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#if defined(CONFIG_RAMBOOT_NAND) || defined(CONFIG_RAMBOOT_SDCARD) || \
+    defined(CONFIG_RAMBOOT_SPIFLASH)
+#define CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#else
+#undef CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR      0xffd00000	/* stack in RAM */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000	/* Size of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
+						- GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc*/
+
+#ifndef CONFIG_NAND_SPL
+#define CONFIG_SYS_NAND_BASE		0xffa00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	0xfffa00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+#else
+#define CONFIG_SYS_NAND_BASE		0xfff00000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS	0xffff00000ull
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
+#endif
+#endif
+
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BASE_LIST	{CONFIG_SYS_NAND_BASE}
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_NAND_FSL_ELBC		1
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 * 1024)
+
+/* NAND boot: 4K NAND loader config */
+#define CONFIG_SYS_NAND_SPL_SIZE	0x1000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	((768 << 10) - 0x2000)
+#define CONFIG_SYS_NAND_U_BOOT_DST	(CONFIG_SYS_INIT_L2_ADDR)
+#define CONFIG_SYS_NAND_U_BOOT_START	(CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	(0)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC	(CONFIG_SYS_INIT_L2_END - 0x2000)
+#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP		((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
+
+/* NAND flash config */
+#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| (2<<BR_DECC_SHIFT)	/* Use HW ECC */ \
+				| BR_PS_8	/* Port Size = 8 bit */ \
+				| BR_MS_FCM		/* MSEL = FCM */ \
+				| BR_V)			/* valid */
+
+#define CONFIG_SYS_NAND_OR_PRELIM	(0xFFF80000	/* length 32K */ \
+				| OR_FCM_CSCT \
+				| OR_FCM_CST \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_1 \
+				| OR_FCM_TRLX \
+				| OR_FCM_EHTR)
+
+#ifdef CONFIG_RAMBOOT_NAND
+#define CONFIG_SYS_BR0_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR0_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#define CONFIG_SYS_BR1_PRELIM  CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
+#define CONFIG_SYS_OR1_PRELIM  CONFIG_FLASH_OR_PRELIM  /* NOR Options */
+#else
+#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
+#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM  /* NOR Options */
+#define CONFIG_SYS_BR1_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
+#define CONFIG_SYS_OR1_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
+#endif
+
+#define CONFIG_SYS_VSC7385_BASE	0xffb00000
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_VSC7385_BASE_PHYS	0xfffb00000ull
+#else
+#define CONFIG_SYS_VSC7385_BASE_PHYS	CONFIG_SYS_VSC7385_BASE
+#endif
+
+#define CONFIG_SYS_BR2_PRELIM	(BR_PHYS_ADDR(CONFIG_SYS_VSC7385_BASE) \
+							| BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR2_PRELIM	(OR_AM_128KB | OR_GPCM_CSNT | OR_GPCM_XACS | \
+				OR_GPCM_SCY_15 | OR_GPCM_SETA | OR_GPCM_TRLX | \
+				OR_GPCM_EHTR | OR_GPCM_EAD)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_NS16550_MIN_FUNCTIONS
+#endif
+
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT		1
+#define CONFIG_OF_BOARD_SETUP		1
+#define CONFIG_OF_STDOUT_VIA_ALIAS	1
+
+/* new uImage format support */
+#define CONFIG_FIT		1
+#define CONFIG_FIT_VERBOSE	1 /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x29} }
+
+/*
+ * I2C2 EEPROM
+ */
+#define CONFIG_ID_EEPROM
+#ifdef CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#endif
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_BUS_NUM	1
+
+#define CONFIG_SYS_I2C_PCA9557_ADDR	0x18
+
+#define CONFIG_RTC_DS1337
+#define CONFIG_SYS_RTC_DS1337_NOOSC
+#define CONFIG_SYS_I2C_RTC_ADDR                0x68
+
+/* eSPI - Enhanced SPI */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED		10000000
+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+#if defined(CONFIG_PCI)
+/* controller 2, Slot 2, tgtid 2, Base address 9000 */
+#define CONFIG_SYS_PCIE2_NAME		"Slot 1"
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xffc10000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xfffc10000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xffc10000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 1, Slot 1, tgtid 1, Base address a000 */
+#define CONFIG_SYS_PCIE1_NAME		"Slot 2"
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xffc00000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xfffc00000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xffc00000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+#undef CONFIG_RTL8139
+
+#ifdef CONFIG_RTL8139
+/* This macro is used by RTL8139 but not defined in PPC architecture */
+#define KSEG1ADDR(x)		(x)
+#define _IO_BASE	0x00000000
+#endif
+
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+
+#endif	/* CONFIG_PCI */
+
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_MII		1	/* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
+#define CONFIG_TSEC1	1
+#define CONFIG_TSEC1_NAME	"eTSEC1"
+#define CONFIG_TSEC2	1
+#define CONFIG_TSEC2_NAME	"eTSEC2"
+#define CONFIG_TSEC3	1
+#define CONFIG_TSEC3_NAME	"eTSEC3"
+
+#define TSEC1_PHY_ADDR		2
+#define TSEC2_PHY_ADDR		0
+#define TSEC3_PHY_ADDR		1
+
+#define CONFIG_VSC7385_ENET
+
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
+#define TSEC1_PHYIDX		0
+#define TSEC2_PHYIDX		0
+#define TSEC3_PHYIDX		0
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+/* The size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE_SIZE	8192
+#endif
+
+#define CONFIG_ETHPRIME		"eTSEC1"
+
+#define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
+
+#endif	/* CONFIG_TSEC_ENET */
+
+/*
+ * Environment
+ */
+#if defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_RAMBOOT_NAND)
+	#define CONFIG_ENV_IS_IN_NAND	1
+	#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+	#define CONFIG_ENV_OFFSET	((768*1024)+CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_RAMBOOT_SDCARD)
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_FSL_FIXED_MMC_LOCATION
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#elif defined(CONFIG_RAMBOOT_SPIFLASH)
+	#define CONFIG_ENV_IS_IN_SPI_FLASH
+	#define CONFIG_ENV_SPI_BUS	0
+	#define CONFIG_ENV_SPI_CS	0
+	#define CONFIG_ENV_SPI_MAX_HZ	10000000
+	#define CONFIG_ENV_SPI_MODE	0
+	#define CONFIG_ENV_OFFSET	0x100000	/* 1MB */
+	#define CONFIG_ENV_SECT_SIZE	0x10000
+	#define CONFIG_ENV_SIZE		0x2000
+#endif
+#else
+	#define CONFIG_ENV_IS_IN_FLASH	1
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+	#define CONFIG_ENV_SIZE		0x2000
+	#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#endif
+
+#undef CONFIG_WATCHDOG			/* watchdog disabled */
+
+#define CONFIG_MMC	1
+
+#ifdef CONFIG_MMC
+#define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init */
+#define CONFIG_CMD_MMC
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FSL_ESDHC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#ifdef CONFIG_P2020
+#define CONFIG_SYS_FSL_ESDHC_USE_PIO /* P2020 eSDHC DMA is not functional*/
+#endif
+#endif
+
+#define CONFIG_HAS_FSL_DR_USB
+
+#if defined(CONFIG_HAS_FSL_DR_USB)
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_USB_STORAGE
+#endif
+#endif
+
+#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+						/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH2
+#endif
+
+#define CONFIG_HOSTNAME		P2020RDB
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	u-boot.bin/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 10	/* -1 disables auto-boot */
+#undef  CONFIG_BOOTARGS		/* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"loadaddr=1000000\0"					\
+	"tftpflash=tftpboot $loadaddr $uboot; "			\
+		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" +$filesize; "	\
+		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
+			" +$filesize; "	\
+		"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" $filesize; "	\
+		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
+			" +$filesize; "	\
+		"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
+			" $filesize\0"	\
+	"consoledev=ttyS0\0"				\
+	"ramdiskaddr=2000000\0"			\
+	"ramdiskfile=rootfs.ext2.gz.uboot\0"		\
+	"fdtaddr=c00000\0"				\
+	"fdtfile=p2020rdb.dtb\0"		\
+	"bdev=sda1\0"	\
+	"jffs2nor=mtdblock3\0"	\
+	"norbootaddr=ef080000\0"	\
+	"norfdtaddr=ef040000\0"	\
+	"jffs2nand=mtdblock9\0"	\
+	"nandbootaddr=100000\0"	\
+	"nandfdtaddr=80000\0"		\
+	"nandimgsize=400000\0"		\
+	"nandfdtsize=80000\0"		\
+	"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"	\
+	"vscfw_addr=ef000000\0"	\
+	"othbootargs=ramdisk_size=600000\0" \
+	"usbfatboot=setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"usb start;"			\
+	"fatload usb 0:2 $loadaddr $bootfile;"		\
+	"fatload usb 0:2 $fdtaddr $fdtfile;"	\
+	"fatload usb 0:2 $ramdiskaddr $ramdiskfile;"	\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"		\
+	"usbext2boot=setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"usb start;"			\
+	"ext2load usb 0:4 $loadaddr $bootfile;"		\
+	"ext2load usb 0:4 $fdtaddr $fdtfile;"	\
+	"ext2load usb 0:4 $ramdiskaddr $ramdiskfile;"	\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr\0"		\
+	"norboot=setenv bootargs root=/dev/$jffs2nor rw "	\
+	"console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;"	\
+	"bootm $norbootaddr - $norfdtaddr\0"		\
+	"nandboot=setenv bootargs root=/dev/$jffs2nand rw rootfstype=jffs2 " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"nand read 2000000 $nandbootaddr $nandimgsize;"	\
+	"nand read 3000000 $nandfdtaddr $nandfdtsize;"	\
+	"bootm 2000000 - 3000000;\0"
+
+#define CONFIG_NFSBOOTCOMMAND		\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_HDBOOT			\
+	"setenv bootargs root=/dev/$bdev rw rootdelay=30 "	\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"usb start;"			\
+	"ext2load usb 0:1 $loadaddr /boot/$bootfile;"		\
+	"ext2load usb 0:1 $fdtaddr /boot/$fdtfile;"	\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND		\
+	"setenv bootargs root=/dev/ram rw "	\
+	"console=$consoledev,$baudrate $othbootargs; "	\
+	"tftp $ramdiskaddr $ramdiskfile;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
+
+#endif	/* __CONFIG_H */