X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FMPC8360ERDK.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FMPC8360ERDK.h;h=1b8bad179b5221ce18daec4f127eb5db18e09e10;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/MPC8360ERDK.h b/qemu/roms/u-boot/include/configs/MPC8360ERDK.h new file mode 100644 index 000000000..1b8bad179 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/MPC8360ERDK.h @@ -0,0 +1,620 @@ +/* + * Copyright (C) 2006 Freescale Semiconductor, Inc. + * Dave Liu + * + * Copyright (C) 2007 Logic Product Development, Inc. + * Peter Barada + * + * Copyright (C) 2007 MontaVista Software, Inc. + * Anton Vorontsov + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 /* E300 family */ +#define CONFIG_QE 1 /* Has QE */ +#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ +#define CONFIG_MPC8360ERDK 1 /* MPC8360ERDK board specific */ + +#define CONFIG_SYS_TEXT_BASE 0xFF800000 + +/* + * System Clock Setup + */ +#ifdef CONFIG_CLKIN_33MHZ +#define CONFIG_83XX_CLKIN 33333333 +#define CONFIG_SYS_CLK_FREQ 33333333 +#define CONFIG_PCI_33M 1 +#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_10X1 +#else +#define CONFIG_83XX_CLKIN 66000000 +#define CONFIG_SYS_CLK_FREQ 66000000 +#define CONFIG_PCI_66M 1 +#define HRCWL_CSB_TO_CLKIN_MPC8360ERDK HRCWL_CSB_TO_CLKIN_5X1 +#endif /* CONFIG_CLKIN_33MHZ */ + +/* + * Hardware Reset Configuration Word + */ +#define CONFIG_SYS_HRCW_LOW (\ + HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ + HRCWL_DDR_TO_SCB_CLK_1X1 |\ + HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\ + HRCWL_CORE_TO_CSB_2X1 |\ + HRCWL_CE_TO_PLL_1X15) + +#define CONFIG_SYS_HRCW_HIGH (\ + HRCWH_PCI_HOST |\ + HRCWH_PCI1_ARBITER_ENABLE |\ + HRCWH_PCICKDRV_ENABLE |\ + HRCWH_CORE_ENABLE |\ + HRCWH_FROM_0X00000100 |\ + HRCWH_BOOTSEQ_DISABLE |\ + HRCWH_SW_WATCHDOG_DISABLE |\ + HRCWH_ROM_LOC_LOCAL_16BIT |\ + HRCWH_SECONDARY_DDR_DISABLE |\ + HRCWH_BIG_ENDIAN |\ + HRCWH_LALE_EARLY) + +/* + * System IO Config + */ +#define CONFIG_SYS_SICRH 0x00000000 +#define CONFIG_SYS_SICRL 0x40000000 + +#define CONFIG_BOARD_EARLY_INIT_R + +/* + * IMMR new address + */ +#define CONFIG_SYS_IMMR 0xE0000000 + +/* + * DDR Setup + */ +#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE +#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ + | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) + +#define CONFIG_SYS_83XX_DDR_USES_CS0 + +#define CONFIG_DDR_ECC /* support DDR ECC function */ +#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */ + +/* + * DDRCDR - DDR Control Driver Register + */ +#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_DHC_EN \ + | DDRCDR_ODT \ + | DDRCDR_Q_DRN) + /* 0x80080001 */ + +#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ + +/* + * Manually set up DDR parameters + */ +#define CONFIG_DDR_II +#define CONFIG_SYS_DDR_SIZE 256 /* MB */ +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f +#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \ + | CSCONFIG_ROW_BIT_13 \ + | CSCONFIG_COL_BIT_10 \ + | CSCONFIG_ODT_WR_ONLY_CURRENT) +#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \ + | SDRAM_CFG_ECC_EN) +#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00001000 +#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) +#define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \ + | (1115 << SDRAM_INTERVAL_REFINT_SHIFT)) +#define CONFIG_SYS_DDR_MODE 0x47800432 +#define CONFIG_SYS_DDR_MODE2 0x8000c000 + +#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ + (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ + (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ + (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ + (0 << TIMING_CFG0_WWT_SHIFT) | \ + (0 << TIMING_CFG0_RRT_SHIFT) | \ + (0 << TIMING_CFG0_WRT_SHIFT) | \ + (0 << TIMING_CFG0_RWT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_1 ((TIMING_CFG1_CASLAT_30) | \ + (2 << TIMING_CFG1_WRTORD_SHIFT) | \ + (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ + (3 << TIMING_CFG1_WRREC_SHIFT) | \ + (10 << TIMING_CFG1_REFREC_SHIFT) | \ + (3 << TIMING_CFG1_ACTTORW_SHIFT) | \ + (8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ + (3 << TIMING_CFG1_PRETOACT_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ + (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \ + (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ + (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ + (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ + (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ + (0 << TIMING_CFG2_CPO_SHIFT)) + +#define CONFIG_SYS_DDR_TIMING_3 0x00000000 + +/* + * Memory test + */ +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00100000 + +/* + * The reserved memory + */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* FLASH base address */ + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT +#else +#undef CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ + +/* + * Initial RAM Base Address Setup + */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) + +/* + * Local Bus Configuration & Clock Setup + */ +#define CONFIG_SYS_LCRR_DBYP LCRR_DBYP +#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 +#define CONFIG_SYS_LBC_LBCR 0x00000000 + +/* + * FLASH on the Local Bus + */ +#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ +#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ +#define CONFIG_SYS_FLASH_SIZE 8 /* max FLASH size is 32M */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use intel Flash protection. */ + + /* Window base at flash base */ +#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_32MB) + +#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \ + | BR_PS_16 /* 16 bit port */ \ + | BR_MS_GPCM /* MSEL = GPCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ + | OR_UPM_XAM \ + | OR_GPCM_CSNT \ + | OR_GPCM_ACS_DIV2 \ + | OR_GPCM_XACS \ + | OR_GPCM_SCY_15 \ + | OR_GPCM_TRLX_SET \ + | OR_GPCM_EHTR_SET \ + | OR_GPCM_EAD) + +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ + +#undef CONFIG_SYS_FLASH_CHECKSUM + +/* + * NAND flash on the local bus + */ +#define CONFIG_SYS_NAND_BASE 0x60000000 +#define CONFIG_CMD_NAND 1 +#define CONFIG_NAND_FSL_UPM 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE + +#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE +/* + * [RFC] Comment said 4KB window; code said 256MB window; OR1 says 64MB + * ... What's correct? + */ +#define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256MB) + +/* Port size 8 bit, UPMA */ +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \ + | BR_PS_8 \ + | BR_MS_UPMA \ + | BR_V) + /* 0x60000881 */ +#define CONFIG_SYS_OR1_PRELIM (OR_AM_64MB | OR_UPM_EAD) + /* 0xFC000001 */ + +/* + * Fujitsu MB86277 (MINT) graphics controller + */ +#define CONFIG_SYS_VIDEO_BASE 0x70000000 + +#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_VIDEO_BASE +#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_64MB) + +/* Port size 32 bit, UPMB */ +#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VIDEO_BASE \ + | BR_PS_32 \ + | BR_MS_UPMB \ + | BR_V) + /* 0x000018a1 */ +#define CONFIG_SYS_OR2_PRELIM (OR_AM_64MB | OR_UPM_EAD) + /* 0xFC000001 */ + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_FSL +#define CONFIG_SYS_FSL_I2C_SPEED 400000 +#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 +#define CONFIG_SYS_FSL_I2C2_SPEED 400000 +#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F +#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 +#define CONFIG_SYS_I2C_NOPROBES { {0, 0x52} } + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CONFIG_PCI + +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 +#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE +#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xE0300000 +#define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000 +#define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */ + +#ifdef CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE + +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ + +#endif /* CONFIG_PCI */ + +/* + * QE UEC ethernet configuration + */ +#define CONFIG_UEC_ETH +#define CONFIG_ETHPRIME "UEC0" + +#define CONFIG_UEC_ETH1 /* GETH1 */ + +#ifdef CONFIG_UEC_ETH1 +#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */ +#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC1_TX_CLK QE_CLK9 +#define CONFIG_SYS_UEC1_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC1_PHY_ADDR 2 +#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID +#define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000 +#endif + +#define CONFIG_UEC_ETH2 /* GETH2 */ + +#ifdef CONFIG_UEC_ETH2 +#define CONFIG_SYS_UEC2_UCC_NUM 1 /* UCC2 */ +#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE +#define CONFIG_SYS_UEC2_TX_CLK QE_CLK4 +#define CONFIG_SYS_UEC2_ETH_TYPE GIGA_ETH +#define CONFIG_SYS_UEC2_PHY_ADDR 4 +#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID +#define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000 +#endif + +/* + * Environment + */ + +#ifndef CONFIG_SYS_RAMBOOT +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ +#define CONFIG_ENV_SIZE 0x20000 +#else /* CONFIG_SYS_RAMBOOT */ +#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ +#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +#define CONFIG_ENV_SIZE 0x2000 +#endif /* CONFIG_SYS_RAMBOOT */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_PING +#define CONFIG_CMD_I2C +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#endif + +#if defined(CONFIG_SYS_RAMBOOT) +#undef CONFIG_CMD_SAVEENV +#undef CONFIG_CMD_LOADS +#endif + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ + +#if defined(CONFIG_CMD_KGDB) + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif + + /* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ + /* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * For booting Linux, the board info and command line data + * have to be in the first 256 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ + +/* + * Core HID Setup + */ +#define CONFIG_SYS_HID0_INIT 0x000000000 +#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ + HID0_ENABLE_INSTRUCTION_CACHE) +#define CONFIG_SYS_HID2 HID2_HBE + +/* + * MMU Setup + */ + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* DDR: cache cacheable */ +#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L +#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U + +/* IMMRBAR & PCI IO: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \ + | BATU_BL_4M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L +#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U + +/* NAND: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_NAND_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT2U (CONFIG_SYS_NAND_BASE \ + | BATU_BL_64M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L +#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U + +/* FLASH: icache cacheable, but dcache-inhibit and guarded */ +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \ + | BATU_BL_32M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U + +/* Stack in dcache: cacheable, no memory coherence */ +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \ + | BATL_PP_RW) +#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \ + | BATU_BL_128K \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L +#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U + +#define CONFIG_SYS_IBAT5L (CONFIG_SYS_VIDEO_BASE \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT5U (CONFIG_SYS_VIDEO_BASE \ + | BATU_BL_64M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L +#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U + +#ifdef CONFIG_PCI +/* PCI MEM space: cacheable */ +#define CONFIG_SYS_IBAT6L (CONFIG_SYS_PCI1_MEM_PHYS \ + | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U (CONFIG_SYS_PCI1_MEM_PHYS \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +/* PCI MMIO space: cache-inhibit and guarded */ +#define CONFIG_SYS_IBAT7L (CONFIG_SYS_PCI1_MMIO_PHYS \ + | BATL_PP_RW \ + | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_IBAT7U (CONFIG_SYS_PCI1_MMIO_PHYS \ + | BATU_BL_256M \ + | BATU_VS \ + | BATU_VP) +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U +#else /* CONFIG_PCI */ +#define CONFIG_SYS_IBAT6L (0) +#define CONFIG_SYS_IBAT6U (0) +#define CONFIG_SYS_IBAT7L (0) +#define CONFIG_SYS_IBAT7U (0) +#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L +#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U +#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L +#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ +#endif + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#if defined(CONFIG_UEC_ETH) +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 +#define CONFIG_HAS_ETH2 +#define CONFIG_HAS_ETH3 +#endif + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_LOADADDR a00000 +#define CONFIG_HOSTNAME mpc8360erdk +#define CONFIG_BOOTFILE "uImage" + +#define CONFIG_ROOTPATH "/nfsroot/" + +#define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "loadaddr=a00000\0" \ + "fdtaddr=900000\0" \ + "fdtfile=mpc836x_rdk.dtb\0" \ + "fsfile=fs\0" \ + "ubootfile=u-boot.bin\0" \ + "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),"\ + "-(rootfs)\0" \ + "setbootargs=setenv bootargs console=$consoledev,$baudrate " \ + "$mtdparts panic=1\0" \ + "adddhcpargs=setenv bootargs $bootargs ip=on\0" \ + "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:" \ + "$gatewayip:$netmask:$hostname:$netdev:off " \ + "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0" \ + "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 " \ + "rootfstype=jffs2 rw\0" \ + "tftp_get_uboot=tftp 100000 $ubootfile\0" \ + "tftp_get_kernel=tftp $loadaddr $bootfile\0" \ + "tftp_get_dtb=tftp $fdtaddr $fdtfile\0" \ + "tftp_get_fs=tftp c00000 $fsfile\0" \ + "nand_erase_kernel=nand erase 0 400000\0" \ + "nand_erase_dtb=nand erase 400000 20000\0" \ + "nand_erase_fs=nand erase 420000 3be0000\0" \ + "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0" \ + "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0" \ + "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0" \ + "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0" \ + "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0" \ + "nor_reflash=protect off ff800000 ff87ffff ; " \ + "erase ff800000 ff87ffff ; " \ + "cp.b 100000 ff800000 $filesize\0" \ + "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel " \ + "nand_write_kernel\0" \ + "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\ + "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0" \ + "nand_reflash=run nand_reflash_kernel nand_reflash_dtb " \ + "nand_reflash_fs\0" \ + "boot_m=bootm $loadaddr - $fdtaddr\0" \ + "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\ + "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\ + "boot_m\0" \ + "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\ + "boot_m\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run dhcpboot" + +#endif /* __CONFIG_H */