X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FMPC8266ADS.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FMPC8266ADS.h;h=8d9c8fb45c956392e426ef02e2f36f6931f8dc23;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/MPC8266ADS.h b/qemu/roms/u-boot/include/configs/MPC8266ADS.h new file mode 100644 index 000000000..8d9c8fb45 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/MPC8266ADS.h @@ -0,0 +1,563 @@ +/* + * (C) Copyright 2001 + * Stuart Hughes + * This file is based on similar values for other boards found in other + * U-Boot config files, and some that I found in the mpc8260ads manual. + * + * Note: my board is a PILOT rev. + * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Config header file for a MPC8266ADS Pilot 16M Ram Simm, 8Mbytes Flash Simm + */ + +/* !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! + !! !! + !! This configuration requires JP3 to be in position 1-2 to work !! + !! To make it work for the default, the CONFIG_SYS_TEXT_BASE define in !! + !! board/mpc8266ads/config.mk must be changed from 0xfe000000 to !! + !! 0xfff00000 !! + !! The CONFIG_SYS_HRCW_MASTER define below must also be changed to match !! + !! !! + !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC8266ADS 1 /* ...on motorola ADS board */ +#define CONFIG_CPM2 1 /* Has a CPM2 */ + +#define CONFIG_SYS_TEXT_BASE 0xfe000000 + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */ + +/* allow serial and ethaddr to be overwritten */ +#define CONFIG_ENV_OVERWRITE + +/* + * select serial console configuration + * + * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then + * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 + * for SCC). + * + * if CONFIG_CONS_NONE is defined, then the serial console routines must + * defined elsewhere (for example, on the cogent platform, there are serial + * ports on the motherboard which are used for the serial console - see + * cogent/cma101/serial.[ch]). + */ +#undef CONFIG_CONS_ON_SMC /* define if console on SMC */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ + +/* + * select ethernet configuration + * + * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then + * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3 + * for FCC) + * + * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be + * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset. + */ +#undef CONFIG_ETHER_ON_SCC /* define if ether on SCC */ +#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */ +#undef CONFIG_ETHER_NONE /* define if ether on something else */ +#define CONFIG_ETHER_INDEX 2 /* which channel for ether */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_BITBANGMII /* bit-bang MII PHY management */ +/* + * Port pins used for bit-banged MII communictions (if applicable). + */ +#define MDIO_PORT 2 /* Port C */ +#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \ + (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT ) +#define MDC_DECLARE MDIO_DECLARE + +#define MDIO_ACTIVE (iop->pdir |= 0x00400000) +#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) +#define MDIO_READ ((iop->pdat & 0x00400000) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ + else iop->pdat &= ~0x00400000 + +#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ + else iop->pdat &= ~0x00200000 + +#define MIIDELAY udelay(1) + +#if (CONFIG_ETHER_INDEX == 2) + +/* + * - Rx-CLK is CLK13 + * - Tx-CLK is CLK14 + * - Select bus for bd/buffers (see 28-13) + * - Half duplex + */ +# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) +# define CONFIG_SYS_CPMFCR_RAMTYPE 0 +# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) + +#endif /* CONFIG_ETHER_INDEX */ + +/* other options */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* PCI */ +#define CONFIG_PCI +#define CONFIG_PCI_INDIRECT_BRIDGE +#define CONFIG_PCI_PNP +#define CONFIG_PCI_BOOTDELAY 0 +#undef CONFIG_PCI_SCAN_SHOW + +/*----------------------------------------------------------------------- + * Definitions for Serial Presence Detect EEPROM address + * (to get SDRAM settings) + */ +#define SPD_EEPROM_ADDRESS 0x50 + +#define CONFIG_8260_CLKIN 66000000 /* in Hz */ +#define CONFIG_BAUDRATE 115200 + +/* + * Command line configuration. + */ +#include + +/* Commands we want, that are not part of default set */ +#define CONFIG_CMD_ASKENV /* ask for env variable */ +#define CONFIG_CMD_CACHE /* icache, dcache */ +#define CONFIG_CMD_DHCP /* DHCP Support */ +#define CONFIG_CMD_DIAG /* Diagnostics */ +#define CONFIG_CMD_IMMAP /* IMMR dump support */ +#define CONFIG_CMD_IRQ /* irqinfo */ +#define CONFIG_CMD_MII /* MII support */ +#define CONFIG_CMD_PCI /* pciinfo */ +#define CONFIG_CMD_PING /* ping support */ +#define CONFIG_CMD_PORTIO /* Port I/O */ +#define CONFIG_CMD_REGINFO /* Register dump */ +#define CONFIG_CMD_SAVES /* save S record dump */ +#define CONFIG_CMD_SDRAM /* SDRAM DIMM SPD info printout */ + +/* Commands from default set we don't need */ +#undef CONFIG_CMD_FPGA /* FPGA configuration Support */ +#undef CONFIG_CMD_SETGETDCR /* DCR support on 4xx */ + +/* Define a command string that is automatically executed when no character + * is read on the console interface withing "Boot Delay" after reset. + */ +#undef CONFIG_BOOT_ROOT_INITRD /* Use ram disk for the root file system */ +#define CONFIG_BOOT_ROOT_NFS /* Use a NFS mounted root file system */ + +#ifdef CONFIG_BOOT_ROOT_INITRD +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/ram0 rw " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_INITRD */ + +#ifdef CONFIG_BOOT_ROOT_NFS +#define CONFIG_BOOTCOMMAND \ + "version;" \ + "echo;" \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \ + "bootm" +#endif /* CONFIG_BOOT_ROOT_NFS */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_DNS + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#if defined(CONFIG_CMD_KGDB) +#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ +#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ +#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ +#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */ +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ +#endif + +#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks passsed to Linux in MHz */ + /* for versions < 2.4.5-pre5 */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +#define CONFIG_SYS_FLASH_BASE 0xFE000000 +#define FLASH_BASE 0xFE000000 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_SIZE 8 +#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 5 /* Timeout for Flash Write (in ms) */ + +#undef CONFIG_SYS_FLASH_CHECKSUM + +/* this is stuff came out of the Motorola docs */ +/* Only change this if you also change the Hardware configuration Word */ +#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000 + +/* Set IMMR to 0xF0000000 or above to boot Linux */ +#define CONFIG_SYS_IMMR 0xF0000000 +#define CONFIG_SYS_BCSR 0xF8000000 +#define CONFIG_SYS_PCI_INT 0xF8200000 /* PCI interrupt controller */ + +/* Define CONFIG_VERY_BIG_RAM to allow use of SDRAMs larger than 256MBytes + */ +/*#define CONFIG_VERY_BIG_RAM 1*/ + +/* What should be the base address of SDRAM DIMM and how big is + * it (in Mbytes)? This will normally auto-configure via the SPD. +*/ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_SIZE 16 + +#define SDRAM_SPD_ADDR 0x50 + +/*----------------------------------------------------------------------- + * BR2,BR3 - Base Register + * Ref: Section 10.3.1 on page 10-14 + * OR2,OR3 - Option Register + * Ref: Section 10.3.2 on page 10-16 + *----------------------------------------------------------------------- + */ + +/* Bank 2,3 - SDRAM DIMM + */ + +/* The BR2 is configured as follows: + * + * - Base address of 0x00000000 + * - 64 bit port size (60x bus only) + * - Data errors checking is disabled + * - Read and write access + * - SDRAM 60x bus + * - Access are handled by the memory controller according to MSEL + * - Not used for atomic operations + * - No data pipelining is done + * - Valid + */ +#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +#define CONFIG_SYS_BR3_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ + BRx_PS_64 |\ + BRx_MS_SDRAM_P |\ + BRx_V) + +/* With a 64 MB DIMM, the OR2 is configured as follows: + * + * - 64 MB + * - 4 internal banks per device + * - Row start address bit is A8 with PSDMR[PBI] = 0 + * - 12 row address lines + * - Back-to-back page mode + * - Internal bank interleaving within save device enabled + */ +#if (CONFIG_SYS_SDRAM_SIZE == 64) +#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM_SIZE) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI0_A8 |\ + ORxS_NUMR_12) +#elif (CONFIG_SYS_SDRAM_SIZE == 16) +#define CONFIG_SYS_OR2_PRELIM (0xFF000C80) +#else +#error "INVALID SDRAM CONFIGURATION" +#endif + +/*----------------------------------------------------------------------- + * PSDMR - 60x Bus SDRAM Mode Register + * Ref: Section 10.3.3 on page 10-21 + *----------------------------------------------------------------------- + */ + +#if (CONFIG_SYS_SDRAM_SIZE == 64) +/* With a 64 MB DIMM, the PSDMR is configured as follows: + * + * - Bank Based Interleaving, + * - Refresh Enable, + * - Address Multiplexing where A5 is output on A14 pin + * (A6 on A15, and so on), + * - use address pins A14-A16 as bank select, + * - A9 is output on SDA10 during an ACTIVATE command, + * - earliest timing for ACTIVATE command after REFRESH command is 7 clocks, + * - earliest timing for ACTIVATE or REFRESH command after PRECHARGE command + * is 3 clocks, + * - earliest timing for READ/WRITE command after ACTIVATE command is + * 2 clocks, + * - earliest timing for PRECHARGE after last data was read is 1 clock, + * - earliest timing for PRECHARGE after last data was written is 1 clock, + * - CAS Latency is 2. + */ +#define CONFIG_SYS_PSDMR (PSDMR_RFEN |\ + PSDMR_SDAM_A14_IS_A5 |\ + PSDMR_BSMA_A14_A16 |\ + PSDMR_SDA10_PBI0_A9 |\ + PSDMR_RFRC_7_CLK |\ + PSDMR_PRETOACT_3W |\ + PSDMR_ACTTORW_2W |\ + PSDMR_LDOTOPRE_1C |\ + PSDMR_WRC_1C |\ + PSDMR_CL_2) +#elif (CONFIG_SYS_SDRAM_SIZE == 16) +/* With a 16 MB DIMM, the PSDMR is configured as follows: + * + * configuration parameters found in Motorola documentation + */ +#define CONFIG_SYS_PSDMR (0x016EB452) +#else +#error "INVALID SDRAM CONFIGURATION" +#endif + +#define RS232EN_1 0x02000002 +#define RS232EN_2 0x01000001 +#define FETHIEN 0x08000008 +#define FETH_RST 0x04000004 + +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +/* Use this HRCW for booting from address 0xfe00000 (JP3 in setting 1-2) */ +/* 0x0EB2B645 */ +#define CONFIG_SYS_HRCW_MASTER (( HRCW_BPS11 | HRCW_CIP ) |\ + ( HRCW_L2CPC10 | HRCW_DPPC11 | HRCW_ISB010 ) |\ + ( HRCW_BMS | HRCW_MMR11 | HRCW_LBPC01 | HRCW_APPC10 ) |\ + ( HRCW_CS10PC01 | HRCW_MODCK_H0101 ) \ + ) + +/* Use this HRCW for booting from address 0xfff0000 (JP3 in setting 2-3) */ +/* #define CONFIG_SYS_HRCW_MASTER 0x0cb23645 */ + +/* This value should actually be situated in the first 256 bytes of the FLASH + which on the standard MPC8266ADS board is at address 0xFF800000 + The linker script places it at 0xFFF00000 instead. + + It still works, however, as long as the ADS board jumper JP3 is set to + position 2-3 so the board is using the BCSR as Hardware Configuration Word + + If you want to use the one defined here instead, ust copy the first 256 bytes from + 0xfff00000 to 0xff800000 (for 8MB flash) + + - Rune + +*/ + +/* no slaves */ +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE + +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT +#endif + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +#ifndef CONFIG_SYS_RAMBOOT +# define CONFIG_ENV_IS_IN_FLASH 1 +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) +# define CONFIG_ENV_SECT_SIZE 0x40000 +#else +# define CONFIG_ENV_IS_IN_NVRAM 1 +# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) +# define CONFIG_ENV_SIZE 0x200 +#endif /* CONFIG_SYS_RAMBOOT */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * HIDx - Hardware Implementation-dependent Registers 2-11 + *----------------------------------------------------------------------- + * HID0 also contains cache control - initially enable both caches and + * invalidate contents, then the final state leaves only the instruction + * cache enabled. Note that Power-On and Hard reset invalidate the caches, + * but Soft reset does not. + * + * HID1 has only read-only information - nothing to set. + */ +/*#define CONFIG_SYS_HID0_INIT 0 */ +#define CONFIG_SYS_HID0_INIT (HID0_ICE |\ + HID0_DCE |\ + HID0_ICFI |\ + HID0_DCI |\ + HID0_IFEM |\ + HID0_ABE) + +#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE ) + +#define CONFIG_SYS_HID2 0 + +#define CONFIG_SYS_SYPCR 0xFFFFFFC3 +#define CONFIG_SYS_BCR 0x004C0000 +#define CONFIG_SYS_SIUMCR 0x4E64C000 +#define CONFIG_SYS_SCCR 0x00000000 + +/* local bus memory map + * + * 0x00000000-0x03FFFFFF 64MB SDRAM + * 0x80000000-0x9FFFFFFF 512MB outbound prefetchable PCI memory window + * 0xA0000000-0xBFFFFFFF 512MB outbound non-prefetchable PCI memory window + * 0xF0000000-0xF001FFFF 128KB MPC8266 internal memory + * 0xF4000000-0xF7FFFFFF 64MB outbound PCI I/O window + * 0xF8000000-0xF8007FFF 32KB BCSR + * 0xF8100000-0xF8107FFF 32KB ATM UNI + * 0xF8200000-0xF8207FFF 32KB PCI interrupt controller + * 0xF8300000-0xF8307FFF 32KB EEPROM + * 0xFE000000-0xFFFFFFFF 32MB flash + */ +#define CONFIG_SYS_BR0_PRELIM 0xFE001801 /* flash */ +#define CONFIG_SYS_OR0_PRELIM 0xFE000836 +#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_BCSR | 0x1801) /* BCSR */ +#define CONFIG_SYS_OR1_PRELIM 0xFFFF8010 +#define CONFIG_SYS_BR4_PRELIM 0xF8300801 /* EEPROM */ +#define CONFIG_SYS_OR4_PRELIM 0xFFFF8846 +#define CONFIG_SYS_BR5_PRELIM 0xF8100801 /* PM5350 ATM UNI */ +#define CONFIG_SYS_OR5_PRELIM 0xFFFF8E36 +#define CONFIG_SYS_BR8_PRELIM (CONFIG_SYS_PCI_INT | 0x1801) /* PCI interrupt controller */ +#define CONFIG_SYS_OR8_PRELIM 0xFFFF8010 + +#define CONFIG_SYS_RMR 0x0001 +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +#define CONFIG_SYS_RCCR 0 +#define CONFIG_SYS_MPTPR 0x00001900 +#define CONFIG_SYS_PSRT 0x00000021 + +/* This address must not exist */ +#define CONFIG_SYS_RESET_ADDRESS 0xFCFFFF00 + +/* PCI Memory map (if different from default map */ +#define CONFIG_SYS_PCI_SLV_MEM_LOCAL CONFIG_SYS_SDRAM_BASE /* Local base */ +#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000 /* PCI base */ +#define CONFIG_SYS_PICMR0_MASK_ATTRIB (PICMR_MASK_512MB | PICMR_ENABLE | \ + PICMR_PREFETCH_EN) + +/* + * These are the windows that allow the CPU to access PCI address space. + * All three PCI master windows, which allow the CPU to access PCI + * prefetch, non prefetch, and IO space (see below), must all fit within + * these windows. + */ + +/* PCIBR0 */ +#define CONFIG_SYS_PCI_MSTR0_LOCAL 0x80000000 /* Local base */ +#define CONFIG_SYS_PCIMSK0_MASK PCIMSK_1GB /* Size of window */ +/* PCIBR1 */ +#define CONFIG_SYS_PCI_MSTR1_LOCAL 0xF4000000 /* Local base */ +#define CONFIG_SYS_PCIMSK1_MASK PCIMSK_64MB /* Size of window */ + +/* + * Master window that allows the CPU to access PCI Memory (prefetch). + * This window will be setup with the first set of Outbound ATU registers + * in the bridge. + */ + +#define CONFIG_SYS_PCI_MSTR_MEM_LOCAL 0x80000000 /* Local base */ +#define CONFIG_SYS_PCI_MSTR_MEM_BUS 0x80000000 /* PCI base */ +#define CONFIG_SYS_CPU_PCI_MEM_START PCI_MSTR_MEM_LOCAL +#define CONFIG_SYS_PCI_MSTR_MEM_SIZE 0x20000000 /* 512MB */ +#define CONFIG_SYS_POCMR0_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE | POCMR_PREFETCH_EN) + +/* + * Master window that allows the CPU to access PCI Memory (non-prefetch). + * This window will be setup with the second set of Outbound ATU registers + * in the bridge. + */ + +#define CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL 0xA0000000 /* Local base */ +#define CONFIG_SYS_PCI_MSTR_MEMIO_BUS 0xA0000000 /* PCI base */ +#define CONFIG_SYS_CPU_PCI_MEMIO_START PCI_MSTR_MEMIO_LOCAL +#define CONFIG_SYS_PCI_MSTR_MEMIO_SIZE 0x20000000 /* 512MB */ +#define CONFIG_SYS_POCMR1_MASK_ATTRIB (POCMR_MASK_512MB | POCMR_ENABLE) + +/* + * Master window that allows the CPU to access PCI IO space. + * This window will be setup with the third set of Outbound ATU registers + * in the bridge. + */ + +#define CONFIG_SYS_PCI_MSTR_IO_LOCAL 0xF4000000 /* Local base */ +#define CONFIG_SYS_PCI_MSTR_IO_BUS 0xF4000000 /* PCI base */ +#define CONFIG_SYS_CPU_PCI_IO_START PCI_MSTR_IO_LOCAL +#define CONFIG_SYS_PCI_MSTR_IO_SIZE 0x04000000 /* 64MB */ +#define CONFIG_SYS_POCMR2_MASK_ATTRIB (POCMR_MASK_64MB | POCMR_ENABLE | POCMR_PCI_IO) + +/* + * JFFS2 partitions + * + */ +/* No command line, one static partition, whole device */ +#undef CONFIG_CMD_MTDPARTS +#define CONFIG_JFFS2_DEV "nor0" +#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF +#define CONFIG_JFFS2_PART_OFFSET 0x00000000 + +/* mtdparts command line support */ +/* +#define CONFIG_CMD_MTDPARTS +#define MTDIDS_DEFAULT "" +#define MTDPARTS_DEFAULT "" +*/ + +#endif /* __CONFIG_H */