X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FBC3450.h;fp=qemu%2Froms%2Fu-boot%2Finclude%2Fconfigs%2FBC3450.h;h=802e9cce1fb61e3ac50c2844bb4417e02d905bfa;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/include/configs/BC3450.h b/qemu/roms/u-boot/include/configs/BC3450.h new file mode 100644 index 000000000..802e9cce1 --- /dev/null +++ b/qemu/roms/u-boot/include/configs/BC3450.h @@ -0,0 +1,541 @@ +/* + * -- Version 1.1 -- + * + * (C) Copyright 2003-2005 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2004-2005 + * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de + * + * (C) Copyright 2005 + * Stefan Strobl, GERSYS GmbH, stefan.strobl@gersys.de. + * + * History: + * 1.1 - add define CONFIG_ZERO_BOOTDELAY_CHECK + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + */ +#define CONFIG_MPC5200 1 /* This is a MPC5200 CPU */ +#define CONFIG_TQM5200 1 /* ... on a TQM5200 module */ + +#define CONFIG_BC3450 1 /* ... on a BC3450 mainboard */ +#define CONFIG_BC3450_PS2 1 /* + a PS/2 converter onboard */ +#define CONFIG_BC3450_IDE 1 /* + IDE drives (Compact Flash) */ +#define CONFIG_BC3450_USB 1 /* + USB support */ +# define CONFIG_FAT 1 /* + FAT support */ +# define CONFIG_EXT2 1 /* + EXT2 support */ +#undef CONFIG_BC3450_BUZZER /* + Buzzer onboard */ +#undef CONFIG_BC3450_CAN /* + CAN transceiver */ +#undef CONFIG_BC3450_DS1340 /* + a RTC DS1340 onboard */ +#undef CONFIG_BC3450_DS3231 /* + a RTC DS3231 onboard tbd */ +#undef CONFIG_BC3450_AC97 /* + AC97 on PSC2, tbd */ +#define CONFIG_BC3450_FP 1 /* + enable FP O/P */ +#undef CONFIG_BC3450_CRT /* + enable CRT O/P (Debug only!) */ + +/* + * Valid values for CONFIG_SYS_TEXT_BASE are: + * 0xFC000000 boot low (standard configuration with room for + * max 64 MByte Flash ROM) + * 0x00100000 boot from RAM (for testing only) + */ +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xFC000000 +#endif + +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* + * AT-PS/2 Multiplexer + */ +#ifdef CONFIG_BC3450_PS2 +# define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ +# define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ +# define CONFIG_PS2SERIAL 6 /* .. on PSC6 */ +# define CONFIG_PS2MULT_DELAY (CONFIG_SYS_HZ/2) /* Initial delay */ +# define CONFIG_BOARD_EARLY_INIT_R +#endif /* CONFIG_BC3450_PS2 */ + +/* + * PCI Mapping: + * 0x40000000 - 0x4fffffff - PCI Memory + * 0x50000000 - 0x50ffffff - PCI IO Space + */ +# define CONFIG_PCI 1 +# define CONFIG_PCI_PNP 1 +/* #define CONFIG_PCI_SCAN_SHOW 1 */ +#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 + +#define CONFIG_PCI_MEM_BUS 0x40000000 +#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS +#define CONFIG_PCI_MEM_SIZE 0x10000000 + +#define CONFIG_PCI_IO_BUS 0x50000000 +#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS +#define CONFIG_PCI_IO_SIZE 0x01000000 + +/*#define CONFIG_EEPRO100 XXX - FIXME: conflicts when CONFIG_MII is enabled */ +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_NS8382X 1 + +/* + * Video console + */ +# define CONFIG_VIDEO +# define CONFIG_VIDEO_SM501 +# define CONFIG_VIDEO_SM501_32BPP +# define CONFIG_CFB_CONSOLE +# define CONFIG_VIDEO_LOGO +# define CONFIG_VGA_AS_SINGLE_DEVICE +# define CONFIG_CONSOLE_EXTRA_INFO /* display Board/Device-Infos */ +# define CONFIG_VIDEO_SW_CURSOR +# define CONFIG_SPLASH_SCREEN +# define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* + * Partitions + */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* + * USB + */ +#ifdef CONFIG_BC3450_USB +# define CONFIG_USB_OHCI +# define CONFIG_USB_STORAGE +#endif /* CONFIG_BC3450_USB */ + +/* + * POST support + */ +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_I2C) + +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +# define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 +#endif /* CONFIG_POST */ + + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_I2C +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MII +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SNTP +#define CONFIG_CMD_BSP + +#ifdef CONFIG_VIDEO + #define CONFIG_CMD_BMP +#endif + +#ifdef CONFIG_BC3450_IDE + #define CONFIG_CMD_IDE +#endif + +#if defined(CONFIG_BC3450_IDE) || defined(CONFIG_BC3450_USB) + #ifdef CONFIG_FAT + #define CONFIG_CMD_FAT + #endif + + #ifdef CONFIG_EXT2 + #define CONFIG_CMD_EXT2 + #endif +#endif + +#ifdef CONFIG_BC3450_USB + #define CONFIG_CMD_USB +#endif + +#ifdef CONFIG_PCI + #define CONFIG_CMD_PCI +#endif + +#ifdef CONFIG_POST + #define CONFIG_CMD_DIAG +#endif + + +#define CONFIG_TIMESTAMP /* display image timestamps */ + +#if (CONFIG_SYS_TEXT_BASE == 0xFC000000) /* Boot low */ +# define CONFIG_SYS_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ + "echo;" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "ipaddr=192.168.1.10\0" \ + "serverip=192.168.1.3\0" \ + "netmask=255.255.255.0\0" \ + "hostname=bc3450\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "kernel_addr=fc0a0000\0" \ + "ramdisk_addr=fc1c0000\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ideargs=setenv bootargs root=/dev/hda2 ro\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "addcons=setenv bootargs $(bootargs) " \ + "console=ttyS0,$(baudrate) console=tty0\0" \ + "flash_self=run ramargs addip addcons;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "flash_nfs=run nfsargs addip addcons; bootm $(kernel_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile); " \ + "run nfsargs addip addcons; bootm\0" \ + "ide_nfs=run nfsargs addip addcons; " \ + "disk 200000 0:1; bootm\0" \ + "ide_ide=run ideargs addip addcons; " \ + "disk 200000 0:1; bootm\0" \ + "usb_self=run usbload; run ramargs addip addcons; " \ + "bootm 200000 400000\0" \ + "usbload=usb reset; usb scan; usbboot 200000 0:1; " \ + "usbboot 400000 0:2\0" \ + "bootfile=uImage\0" \ + "load=tftp 200000 $(u-boot)\0" \ + "u-boot=u-boot.bin\0" \ + "update=protect off FC000000 FC05FFFF;" \ + "erase FC000000 FC05FFFF;" \ + "cp.b 200000 FC000000 $(filesize);" \ + "protect on FC000000 FC05FFFF\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * IPB Bus clocking configuration. + */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ + +/* + * PCI Bus clocking configuration + * + * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if + * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. + */ +#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) +# define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ +#endif + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 */ + +/* + * I2C clock frequency + * + * Please notice, that the resulting clock frequency could differ from the + * configured value. This is because the I2C clock is derived from system + * clock over a frequency divider with only a few divider values. U-boot + * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated + * approximation allways lies below the configured value, never above. + */ +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +/* + * EEPROM configuration for I²C EEPROM M24C32 + * M24C64 should work also. For other EEPROMs config should be verified. + * + * The TQM5200 module may hold an EEPROM at address 0x50. + */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x (TQM) */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70 + +/* + * RTC configuration + */ +#if defined (CONFIG_BC3450_DS1340) && !defined (CONFIG_BC3450_DS3231) +# define CONFIG_RTC_M41T11 1 +# define CONFIG_SYS_I2C_RTC_ADDR 0x68 +#else +# define CONFIG_RTC_MPC5200 1 /* use MPC5200 internal RTC */ +# define CONFIG_BOARD_EARLY_INIT_R +#endif + +/* + * Flash configuration + */ +#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_TEXT_BASE /* 0xFC000000 */ + +/* use CFI flash driver if no module variant is spezified */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +#if !defined(CONFIG_SYS_LOWBOOT) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) +#else /* CONFIG_SYS_LOWBOOT */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) +#endif /* CONFIG_SYS_LOWBOOT */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Dynamic MTD partition support */ +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ +#define CONFIG_FLASH_CFI_MTD +#define MTDIDS_DEFAULT "nor0=TQM5200-0" +#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ + "1408k(kernel)," \ + "2m(initrd)," \ + "4m(small-fs)," \ + "16m(big-fs)," \ + "8m(misc)" + +/* + * Environment settings + */ +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_SECT_SIZE 0x20000 +#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) + +/* + * Memory map + */ +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_POST_SIZE +#else +# define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE +#endif /*CONFIG_POST*/ + +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 +#endif + +#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + * + * Define CONFIG_MPC5xxx_MII10 to force FEC at 10MBIT + */ +#define CONFIG_MPC5xxx_FEC 1 +#define CONFIG_MPC5xxx_FEC_MII100 +#undef CONFIG_MPC5xxx_MII10 +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration on BC3450 + * + * PSC1: UART1 (Service-UART) [0x xxxxxxx4] + * PSC2: UART2 [0x xxxxxx4x] + * or: AC/97 if CONFIG_BC3450_AC97 [0x xxxxxx2x] + * PSC3: USB2 [0x xxxxx1xx] + * USB: UART4(ext.)/UART5(int.) [0x xxxx2xxx] + * (this has to match + * CONFIG_USB_CONFIG which is + * used by usb_ohci.c to set + * the USB ports) + * Eth: 10/100Mbit Ethernet [0x xxx0xxxx] + * (this is reset to '5' + * in FEC driver: fec.c) + * PSC6: UART6 (int. to PS/2 contr.) [0x xx5xxxxx] + * ATA/CS: ??? [0x x1xxxxxx] + * FIXME! UM Fig 2-10 suggests [0x x0xxxxxx] + * CS1: Use Pin gpio_wkup_6 as second + * SDRAM chip select (mem_cs1) + * Timer: CAN2 / SPI + * I2C: CAN1 / I²C2 [0x bxxxxxxx] + */ +#ifdef CONFIG_BC3450_AC97 +# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502124 +#else /* PSC2=UART2 */ +# define CONFIG_SYS_GPS_PORT_CONFIG 0xb1502144 +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max no of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg. Buffer Size */ + +#define CONFIG_SYS_ALT_MEMTEST /* Enable an alternative, */ + /* more extensive mem test */ + +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ + +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if defined(CONFIG_CMD_KGDB) +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Enable loopw command. + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE + +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 +# define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +#else +# define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ +#endif +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE + +/* automatic configuration of chip selects */ +#ifdef CONFIG_TQM5200 +# define CONFIG_LAST_STAGE_INIT +#endif /* CONFIG_TQM5200 */ + +/* + * SRAM - Do not map below 2 GB in address space, because this area is used + * for SDRAM autosizing. + */ +#ifdef CONFIG_TQM5200 +# define CONFIG_SYS_CS2_START 0xE5000000 +# define CONFIG_SYS_CS2_SIZE 0x100000 /* 1 MByte */ +# define CONFIG_SYS_CS2_CFG 0x0004D930 +#endif /* CONFIG_TQM5200 */ + +/* + * Grafic controller - Do not map below 2 GB in address space, because this + * area is used for SDRAM autosizing. + */ +#ifdef CONFIG_TQM5200 +# define SM501_FB_BASE 0xE0000000 +# define CONFIG_SYS_CS1_START (SM501_FB_BASE) +# define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ +# define CONFIG_SYS_CS1_CFG 0x8F48FF70 +# define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 +#endif /* CONFIG_TQM5200 */ + +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for */ + /* flash and SM501 */ + +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 + +/* + * USB stuff + */ +#define CONFIG_USB_CLOCK 0x0001BBBB +#define CONFIG_USB_CONFIG 0x00002000 /* we're using Port 2 */ + +/* + * IDE/ATA stuff Supports IDE harddisk + */ +#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ + +#define CONFIG_IDE_RESET /* reset for ide supported */ +#define CONFIG_IDE_PREINIT + +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ + +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 + +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA + +/* Offset for data I/O */ +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) + +/* Offset for normal register accesses */ +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) + +/* Offset for alternate registers */ +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) + +/* Interval between registers */ +#define CONFIG_SYS_ATA_STRIDE 4 + +#endif /* __CONFIG_H */