X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fdrivers%2Fusb%2Fhost%2Fohci.h;fp=qemu%2Froms%2Fu-boot%2Fdrivers%2Fusb%2Fhost%2Fohci.h;h=9a4a2c24759111adf185be7cebdbffa0bd1f29b8;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/drivers/usb/host/ohci.h b/qemu/roms/u-boot/drivers/usb/host/ohci.h new file mode 100644 index 000000000..9a4a2c247 --- /dev/null +++ b/qemu/roms/u-boot/drivers/usb/host/ohci.h @@ -0,0 +1,491 @@ +/* + * URB OHCI HCD (Host Controller Driver) for USB. + * + * (C) Copyright 1999 Roman Weissgaerber + * (C) Copyright 2000-2001 David Brownell + * + * usb-ohci.h + */ + +/* + * e.g. PCI controllers need this + */ +#ifdef CONFIG_SYS_OHCI_SWAP_REG_ACCESS +# define ohci_readl(a) __swap_32(*((volatile u32 *)(a))) +# define ohci_writel(a, b) (*((volatile u32 *)(b)) = __swap_32((volatile u32)a)) +#else +# define ohci_readl(a) (*((volatile u32 *)(a))) +# define ohci_writel(a, b) (*((volatile u32 *)(b)) = ((volatile u32)a)) +#endif /* CONFIG_SYS_OHCI_SWAP_REG_ACCESS */ + +/* functions for doing board or CPU specific setup/cleanup */ +int usb_board_stop(void); + +int usb_cpu_init(void); +int usb_cpu_stop(void); +int usb_cpu_init_fail(void); + +static int cc_to_error[16] = { + +/* mapping of the OHCI CC status to error codes */ + /* No Error */ 0, + /* CRC Error */ USB_ST_CRC_ERR, + /* Bit Stuff */ USB_ST_BIT_ERR, + /* Data Togg */ USB_ST_CRC_ERR, + /* Stall */ USB_ST_STALLED, + /* DevNotResp */ -1, + /* PIDCheck */ USB_ST_BIT_ERR, + /* UnExpPID */ USB_ST_BIT_ERR, + /* DataOver */ USB_ST_BUF_ERR, + /* DataUnder */ USB_ST_BUF_ERR, + /* reservd */ -1, + /* reservd */ -1, + /* BufferOver */ USB_ST_BUF_ERR, + /* BuffUnder */ USB_ST_BUF_ERR, + /* Not Access */ -1, + /* Not Access */ -1 +}; + +static const char *cc_to_string[16] = { + "No Error", + "CRC: Last data packet from endpoint contained a CRC error.", + "BITSTUFFING: Last data packet from endpoint contained a bit " \ + "stuffing violation", + "DATATOGGLEMISMATCH: Last packet from endpoint had data toggle PID\n" \ + "that did not match the expected value.", + "STALL: TD was moved to the Done Queue because the endpoint returned" \ + " a STALL PID", + "DEVICENOTRESPONDING: Device did not respond to token (IN) or did\n" \ + "not provide a handshake (OUT)", + "PIDCHECKFAILURE: Check bits on PID from endpoint failed on data PID\n"\ + "(IN) or handshake (OUT)", + "UNEXPECTEDPID: Receive PID was not valid when encountered or PID\n" \ + "value is not defined.", + "DATAOVERRUN: The amount of data returned by the endpoint exceeded\n" \ + "either the size of the maximum data packet allowed\n" \ + "from the endpoint (found in MaximumPacketSize field\n" \ + "of ED) or the remaining buffer size.", + "DATAUNDERRUN: The endpoint returned less than MaximumPacketSize\n" \ + "and that amount was not sufficient to fill the\n" \ + "specified buffer", + "reserved1", + "reserved2", + "BUFFEROVERRUN: During an IN, HC received data from endpoint faster\n" \ + "than it could be written to system memory", + "BUFFERUNDERRUN: During an OUT, HC could not retrieve data from\n" \ + "system memory fast enough to keep up with data USB " \ + "data rate.", + "NOT ACCESSED: This code is set by software before the TD is placed" \ + "on a list to be processed by the HC.(1)", + "NOT ACCESSED: This code is set by software before the TD is placed" \ + "on a list to be processed by the HC.(2)", +}; + +/* ED States */ + +#define ED_NEW 0x00 +#define ED_UNLINK 0x01 +#define ED_OPER 0x02 +#define ED_DEL 0x04 +#define ED_URB_DEL 0x08 + +/* usb_ohci_ed */ +struct ed { + __u32 hwINFO; + __u32 hwTailP; + __u32 hwHeadP; + __u32 hwNextED; + + struct ed *ed_prev; + __u8 int_period; + __u8 int_branch; + __u8 int_load; + __u8 int_interval; + __u8 state; + __u8 type; + __u16 last_iso; + struct ed *ed_rm_list; + + struct usb_device *usb_dev; + void *purb; + __u32 unused[2]; +} __attribute__((aligned(16))); +typedef struct ed ed_t; + + +/* TD info field */ +#define TD_CC 0xf0000000 +#define TD_CC_GET(td_p) ((td_p >>28) & 0x0f) +#define TD_CC_SET(td_p, cc) (td_p) = ((td_p) & 0x0fffffff) | (((cc) & 0x0f) << 28) +#define TD_EC 0x0C000000 +#define TD_T 0x03000000 +#define TD_T_DATA0 0x02000000 +#define TD_T_DATA1 0x03000000 +#define TD_T_TOGGLE 0x00000000 +#define TD_R 0x00040000 +#define TD_DI 0x00E00000 +#define TD_DI_SET(X) (((X) & 0x07)<< 21) +#define TD_DP 0x00180000 +#define TD_DP_SETUP 0x00000000 +#define TD_DP_IN 0x00100000 +#define TD_DP_OUT 0x00080000 + +#define TD_ISO 0x00010000 +#define TD_DEL 0x00020000 + +/* CC Codes */ +#define TD_CC_NOERROR 0x00 +#define TD_CC_CRC 0x01 +#define TD_CC_BITSTUFFING 0x02 +#define TD_CC_DATATOGGLEM 0x03 +#define TD_CC_STALL 0x04 +#define TD_DEVNOTRESP 0x05 +#define TD_PIDCHECKFAIL 0x06 +#define TD_UNEXPECTEDPID 0x07 +#define TD_DATAOVERRUN 0x08 +#define TD_DATAUNDERRUN 0x09 +#define TD_BUFFEROVERRUN 0x0C +#define TD_BUFFERUNDERRUN 0x0D +#define TD_NOTACCESSED 0x0F + + +#define MAXPSW 1 + +struct td { + __u32 hwINFO; + __u32 hwCBP; /* Current Buffer Pointer */ + __u32 hwNextTD; /* Next TD Pointer */ + __u32 hwBE; /* Memory Buffer End Pointer */ + +/* #ifndef CONFIG_MPC5200 /\* this seems wrong *\/ */ + __u16 hwPSW[MAXPSW]; +/* #endif */ + __u8 unused; + __u8 index; + struct ed *ed; + struct td *next_dl_td; + struct usb_device *usb_dev; + int transfer_len; + __u32 data; + + __u32 unused2[2]; +} __attribute__((aligned(32))); +typedef struct td td_t; + +#define OHCI_ED_SKIP (1 << 14) + +/* + * The HCCA (Host Controller Communications Area) is a 256 byte + * structure defined in the OHCI spec. that the host controller is + * told the base address of. It must be 256-byte aligned. + */ + +#define NUM_INTS 32 /* part of the OHCI standard */ +struct ohci_hcca { + __u32 int_table[NUM_INTS]; /* Interrupt ED table */ +#if defined(CONFIG_MPC5200) + __u16 pad1; /* set to 0 on each frame_no change */ + __u16 frame_no; /* current frame number */ +#else + __u16 frame_no; /* current frame number */ + __u16 pad1; /* set to 0 on each frame_no change */ +#endif + __u32 done_head; /* info returned for an interrupt */ + u8 reserved_for_hc[116]; +} __attribute__((aligned(256))); + + +/* + * Maximum number of root hub ports. + */ +#ifndef CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS +# error "CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS undefined!" +#endif + +/* + * This is the structure of the OHCI controller's memory mapped I/O + * region. This is Memory Mapped I/O. You must use the ohci_readl() and + * ohci_writel() macros defined in this file to access these!! + */ +struct ohci_regs { + /* control and status registers */ + __u32 revision; + __u32 control; + __u32 cmdstatus; + __u32 intrstatus; + __u32 intrenable; + __u32 intrdisable; + /* memory pointers */ + __u32 hcca; + __u32 ed_periodcurrent; + __u32 ed_controlhead; + __u32 ed_controlcurrent; + __u32 ed_bulkhead; + __u32 ed_bulkcurrent; + __u32 donehead; + /* frame counters */ + __u32 fminterval; + __u32 fmremaining; + __u32 fmnumber; + __u32 periodicstart; + __u32 lsthresh; + /* Root hub ports */ + struct ohci_roothub_regs { + __u32 a; + __u32 b; + __u32 status; + __u32 portstatus[CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS]; + } roothub; +} __attribute__((aligned(32))); + +/* Some EHCI controls */ +#define EHCI_USBCMD_OFF 0x20 +#define EHCI_USBCMD_HCRESET (1 << 1) + +/* OHCI CONTROL AND STATUS REGISTER MASKS */ + +/* + * HcControl (control) register masks + */ +#define OHCI_CTRL_CBSR (3 << 0) /* control/bulk service ratio */ +#define OHCI_CTRL_PLE (1 << 2) /* periodic list enable */ +#define OHCI_CTRL_IE (1 << 3) /* isochronous enable */ +#define OHCI_CTRL_CLE (1 << 4) /* control list enable */ +#define OHCI_CTRL_BLE (1 << 5) /* bulk list enable */ +#define OHCI_CTRL_HCFS (3 << 6) /* host controller functional state */ +#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */ +#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */ +#define OHCI_CTRL_RWE (1 << 10) /* remote wakeup enable */ + +/* pre-shifted values for HCFS */ +# define OHCI_USB_RESET (0 << 6) +# define OHCI_USB_RESUME (1 << 6) +# define OHCI_USB_OPER (2 << 6) +# define OHCI_USB_SUSPEND (3 << 6) + +/* + * HcCommandStatus (cmdstatus) register masks + */ +#define OHCI_HCR (1 << 0) /* host controller reset */ +#define OHCI_CLF (1 << 1) /* control list filled */ +#define OHCI_BLF (1 << 2) /* bulk list filled */ +#define OHCI_OCR (1 << 3) /* ownership change request */ +#define OHCI_SOC (3 << 16) /* scheduling overrun count */ + +/* + * masks used with interrupt registers: + * HcInterruptStatus (intrstatus) + * HcInterruptEnable (intrenable) + * HcInterruptDisable (intrdisable) + */ +#define OHCI_INTR_SO (1 << 0) /* scheduling overrun */ +#define OHCI_INTR_WDH (1 << 1) /* writeback of done_head */ +#define OHCI_INTR_SF (1 << 2) /* start frame */ +#define OHCI_INTR_RD (1 << 3) /* resume detect */ +#define OHCI_INTR_UE (1 << 4) /* unrecoverable error */ +#define OHCI_INTR_FNO (1 << 5) /* frame number overflow */ +#define OHCI_INTR_RHSC (1 << 6) /* root hub status change */ +#define OHCI_INTR_OC (1 << 30) /* ownership change */ +#define OHCI_INTR_MIE (1 << 31) /* master interrupt enable */ + + +/* Virtual Root HUB */ +struct virt_root_hub { + int devnum; /* Address of Root Hub endpoint */ + void *dev; /* was urb */ + void *int_addr; + int send; + int interval; +}; + +/* USB HUB CONSTANTS (not OHCI-specific; see hub.h) */ + +/* destination of request */ +#define RH_INTERFACE 0x01 +#define RH_ENDPOINT 0x02 +#define RH_OTHER 0x03 + +#define RH_CLASS 0x20 +#define RH_VENDOR 0x40 + +/* Requests: bRequest << 8 | bmRequestType */ +#define RH_GET_STATUS 0x0080 +#define RH_CLEAR_FEATURE 0x0100 +#define RH_SET_FEATURE 0x0300 +#define RH_SET_ADDRESS 0x0500 +#define RH_GET_DESCRIPTOR 0x0680 +#define RH_SET_DESCRIPTOR 0x0700 +#define RH_GET_CONFIGURATION 0x0880 +#define RH_SET_CONFIGURATION 0x0900 +#define RH_GET_STATE 0x0280 +#define RH_GET_INTERFACE 0x0A80 +#define RH_SET_INTERFACE 0x0B00 +#define RH_SYNC_FRAME 0x0C80 +/* Our Vendor Specific Request */ +#define RH_SET_EP 0x2000 + + +/* Hub port features */ +#define RH_PORT_CONNECTION 0x00 +#define RH_PORT_ENABLE 0x01 +#define RH_PORT_SUSPEND 0x02 +#define RH_PORT_OVER_CURRENT 0x03 +#define RH_PORT_RESET 0x04 +#define RH_PORT_POWER 0x08 +#define RH_PORT_LOW_SPEED 0x09 + +#define RH_C_PORT_CONNECTION 0x10 +#define RH_C_PORT_ENABLE 0x11 +#define RH_C_PORT_SUSPEND 0x12 +#define RH_C_PORT_OVER_CURRENT 0x13 +#define RH_C_PORT_RESET 0x14 + +/* Hub features */ +#define RH_C_HUB_LOCAL_POWER 0x00 +#define RH_C_HUB_OVER_CURRENT 0x01 + +#define RH_DEVICE_REMOTE_WAKEUP 0x00 +#define RH_ENDPOINT_STALL 0x01 + +#define RH_ACK 0x01 +#define RH_REQ_ERR -1 +#define RH_NACK 0x00 + + +/* OHCI ROOT HUB REGISTER MASKS */ + +/* roothub.portstatus [i] bits */ +#define RH_PS_CCS 0x00000001 /* current connect status */ +#define RH_PS_PES 0x00000002 /* port enable status*/ +#define RH_PS_PSS 0x00000004 /* port suspend status */ +#define RH_PS_POCI 0x00000008 /* port over current indicator */ +#define RH_PS_PRS 0x00000010 /* port reset status */ +#define RH_PS_PPS 0x00000100 /* port power status */ +#define RH_PS_LSDA 0x00000200 /* low speed device attached */ +#define RH_PS_CSC 0x00010000 /* connect status change */ +#define RH_PS_PESC 0x00020000 /* port enable status change */ +#define RH_PS_PSSC 0x00040000 /* port suspend status change */ +#define RH_PS_OCIC 0x00080000 /* over current indicator change */ +#define RH_PS_PRSC 0x00100000 /* port reset status change */ + +/* roothub.status bits */ +#define RH_HS_LPS 0x00000001 /* local power status */ +#define RH_HS_OCI 0x00000002 /* over current indicator */ +#define RH_HS_DRWE 0x00008000 /* device remote wakeup enable */ +#define RH_HS_LPSC 0x00010000 /* local power status change */ +#define RH_HS_OCIC 0x00020000 /* over current indicator change */ +#define RH_HS_CRWE 0x80000000 /* clear remote wakeup enable */ + +/* roothub.b masks */ +#define RH_B_DR 0x0000ffff /* device removable flags */ +#define RH_B_PPCM 0xffff0000 /* port power control mask */ + +/* roothub.a masks */ +#define RH_A_NDP (0xff << 0) /* number of downstream ports */ +#define RH_A_PSM (1 << 8) /* power switching mode */ +#define RH_A_NPS (1 << 9) /* no power switching */ +#define RH_A_DT (1 << 10) /* device type (mbz) */ +#define RH_A_OCPM (1 << 11) /* over current protection mode */ +#define RH_A_NOCP (1 << 12) /* no over current protection */ +#define RH_A_POTPGT (0xff << 24) /* power on to power good time */ + +/* urb */ +#define N_URB_TD 48 +typedef struct +{ + ed_t *ed; + __u16 length; /* number of tds associated with this request */ + __u16 td_cnt; /* number of tds already serviced */ + struct usb_device *dev; + int state; + unsigned long pipe; + void *transfer_buffer; + int transfer_buffer_length; + int interval; + int actual_length; + int finished; + td_t *td[N_URB_TD]; /* list pointer to all corresponding TDs associated with this request */ +} urb_priv_t; +#define URB_DEL 1 + +/* + * This is the full ohci controller description + * + * Note how the "proper" USB information is just + * a subset of what the full implementation needs. (Linus) + */ + + +typedef struct ohci { + struct ohci_hcca *hcca; /* hcca */ + /*dma_addr_t hcca_dma;*/ + + int irq; + int disabled; /* e.g. got a UE, we're hung */ + int sleeping; + unsigned long flags; /* for HC bugs */ + + struct ohci_regs *regs; /* OHCI controller's memory */ + + int ohci_int_load[32]; /* load of the 32 Interrupt Chains (for load balancing)*/ + ed_t *ed_rm_list[2]; /* lists of all endpoints to be removed */ + ed_t *ed_bulktail; /* last endpoint of bulk list */ + ed_t *ed_controltail; /* last endpoint of control list */ + int intrstatus; + __u32 hc_control; /* copy of the hc control reg */ + struct usb_device *dev[32]; + struct virt_root_hub rh; + + const char *slot_name; +} ohci_t; + +#define NUM_EDS 8 /* num of preallocated endpoint descriptors */ + +struct ohci_device { + ed_t ed[NUM_EDS]; + int ed_cnt; +}; + +/* hcd */ +/* endpoint */ +static int ep_link(ohci_t * ohci, ed_t * ed); +static int ep_unlink(ohci_t * ohci, ed_t * ed); +static ed_t * ep_add_ed(struct usb_device * usb_dev, unsigned long pipe, + int interval, int load); + +/*-------------------------------------------------------------------------*/ + +/* we need more TDs than EDs */ +#define NUM_TD 64 + +/* +1 so we can align the storage */ +td_t gtd[NUM_TD+1]; +/* pointers to aligned storage */ +td_t *ptd; + +/* TDs ... */ +static inline struct td * +td_alloc (struct usb_device *usb_dev) +{ + int i; + struct td *td; + + td = NULL; + for (i = 0; i < NUM_TD; i++) + { + if (ptd[i].usb_dev == NULL) + { + td = &ptd[i]; + td->usb_dev = usb_dev; + break; + } + } + + return td; +} + +static inline void +ed_free (struct ed *ed) +{ + ed->usb_dev = NULL; +}