X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fdrivers%2Fddr%2Ffsl%2Fmpc85xx_ddr_gen2.c;fp=qemu%2Froms%2Fu-boot%2Fdrivers%2Fddr%2Ffsl%2Fmpc85xx_ddr_gen2.c;h=988b4a494109cb94d8a55bb60a197aa648fc2202;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/drivers/ddr/fsl/mpc85xx_ddr_gen2.c b/qemu/roms/u-boot/drivers/ddr/fsl/mpc85xx_ddr_gen2.c
new file mode 100644
index 000000000..988b4a494
--- /dev/null
+++ b/qemu/roms/u-boot/drivers/ddr/fsl/mpc85xx_ddr_gen2.c
@@ -0,0 +1,96 @@
+/*
+ * Copyright 2008-2011 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/processor.h>
+#include <fsl_ddr_sdram.h>
+
+#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
+#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
+#endif
+
+void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
+			     unsigned int ctrl_num, int step)
+{
+	unsigned int i;
+	struct ccsr_ddr __iomem *ddr =
+		(struct ccsr_ddr __iomem *)CONFIG_SYS_FSL_DDR_ADDR;
+
+#if defined(CONFIG_SYS_FSL_ERRATUM_NMG_DDR120) && defined(CONFIG_MPC85xx)
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	uint svr;
+#endif
+
+	if (ctrl_num) {
+		printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
+		return;
+	}
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_NMG_DDR120
+	/*
+	 * Set the DDR IO receiver to an acceptable bias point.
+	 * Fixed in Rev 2.1.
+	 */
+	svr = get_svr();
+	if ((SVR_MAJ(svr) == 1) || IS_SVR_REV(svr, 2, 0)) {
+		if ((regs->ddr_sdram_cfg & SDRAM_CFG_SDRAM_TYPE_MASK) ==
+		   SDRAM_CFG_SDRAM_TYPE_DDR2)
+			out_be32(&gur->ddrioovcr, 0x90000000);
+		else
+			out_be32(&gur->ddrioovcr, 0xA8000000);
+	}
+#endif
+
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i == 0) {
+			out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs0_config, regs->cs[i].config);
+
+		} else if (i == 1) {
+			out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs1_config, regs->cs[i].config);
+
+		} else if (i == 2) {
+			out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs2_config, regs->cs[i].config);
+
+		} else if (i == 3) {
+			out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
+			out_be32(&ddr->cs3_config, regs->cs[i].config);
+		}
+	}
+
+	out_be32(&ddr->timing_cfg_3, regs->timing_cfg_3);
+	out_be32(&ddr->timing_cfg_0, regs->timing_cfg_0);
+	out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
+	out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
+	out_be32(&ddr->sdram_cfg_2, regs->ddr_sdram_cfg_2);
+	out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
+	out_be32(&ddr->sdram_mode_2, regs->ddr_sdram_mode_2);
+	out_be32(&ddr->sdram_md_cntl, regs->ddr_sdram_md_cntl);
+	out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
+	out_be32(&ddr->sdram_data_init, regs->ddr_data_init);
+	out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
+	out_be32(&ddr->init_addr, regs->ddr_init_addr);
+	out_be32(&ddr->init_ext_addr, regs->ddr_init_ext_addr);
+
+	/*
+	 * 200 painful micro-seconds must elapse between
+	 * the DDR clock setup and the DDR config enable.
+	 */
+	udelay(200);
+	asm volatile("sync;isync");
+
+	out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
+
+	/* Poll DDR_SDRAM_CFG_2[D_INIT] bit until auto-data init is done.  */
+	while (in_be32(&ddr->sdram_cfg_2) & 0x10) {
+		udelay(10000);		/* throttle polling rate */
+	}
+}