X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Fti%2Fevm%2Fevm.c;fp=qemu%2Froms%2Fu-boot%2Fboard%2Fti%2Fevm%2Fevm.c;h=81dd081d76a98b6f864037367abf05cc12e934d4;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/board/ti/evm/evm.c b/qemu/roms/u-boot/board/ti/evm/evm.c new file mode 100644 index 000000000..81dd081d7 --- /dev/null +++ b/qemu/roms/u-boot/board/ti/evm/evm.c @@ -0,0 +1,266 @@ +/* + * (C) Copyright 2004-2011 + * Texas Instruments, + * + * Author : + * Manikandan Pillai + * + * Derived from Beagle Board and 3430 SDP code by + * Richard Woodruff + * Syed Mohammed Khasim + * + * SPDX-License-Identifier: GPL-2.0+ + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include "evm.h" + +#define OMAP3EVM_GPIO_ETH_RST_GEN1 64 +#define OMAP3EVM_GPIO_ETH_RST_GEN2 7 + +DECLARE_GLOBAL_DATA_PTR; + +static u32 omap3_evm_version; + +u32 get_omap3_evm_rev(void) +{ + return omap3_evm_version; +} + +static void omap3_evm_get_revision(void) +{ +#if defined(CONFIG_CMD_NET) + /* + * Board revision can be ascertained only by identifying + * the Ethernet chipset. + */ + unsigned int smsc_id; + + /* Ethernet PHY ID is stored at ID_REV register */ + smsc_id = readl(CONFIG_SMC911X_BASE + 0x50) & 0xFFFF0000; + printf("Read back SMSC id 0x%x\n", smsc_id); + + switch (smsc_id) { + /* SMSC9115 chipset */ + case 0x01150000: + omap3_evm_version = OMAP3EVM_BOARD_GEN_1; + break; + /* SMSC 9220 chipset */ + case 0x92200000: + default: + omap3_evm_version = OMAP3EVM_BOARD_GEN_2; + } +#else +#if defined(CONFIG_STATIC_BOARD_REV) + /* + * Look for static defintion of the board revision + */ + omap3_evm_version = CONFIG_STATIC_BOARD_REV; +#else + /* + * Fallback to the default above. + */ + omap3_evm_version = OMAP3EVM_BOARD_GEN_2; +#endif +#endif /* CONFIG_CMD_NET */ +} + +#ifdef CONFIG_USB_OMAP3 +/* + * MUSB port on OMAP3EVM Rev >= E requires extvbus programming. + */ +u8 omap3_evm_need_extvbus(void) +{ + u8 retval = 0; + + if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) + retval = 1; + + return retval; +} +#endif + +/* + * Routine: board_init + * Description: Early hardware init. + */ +int board_init(void) +{ + gpmc_init(); /* in SRAM or SDRAM, finish GPMC */ + /* board id for Linux */ + gd->bd->bi_arch_number = MACH_TYPE_OMAP3EVM; + /* boot param addr */ + gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100); + + return 0; +} + +#ifdef CONFIG_SPL_BUILD +/* + * Routine: get_board_mem_timings + * Description: If we use SPL then there is no x-loader nor config header + * so we have to setup the DDR timings ourself on the first bank. This + * provides the timing values back to the function that configures + * the memory. + */ +void get_board_mem_timings(struct board_sdrc_timings *timings) +{ + int pop_mfr, pop_id; + + /* + * We need to identify what PoP memory is on the board so that + * we know what timings to use. To map the ID values please see + * nand_ids.c + */ + identify_nand_chip(&pop_mfr, &pop_id); + + if (pop_mfr == NAND_MFR_HYNIX && pop_id == 0xbc) { + /* 256MB DDR */ + timings->mcfg = HYNIX_V_MCFG_200(256 << 20); + timings->ctrla = HYNIX_V_ACTIMA_200; + timings->ctrlb = HYNIX_V_ACTIMB_200; + } else { + /* 128MB DDR */ + timings->mcfg = MICRON_V_MCFG_165(128 << 20); + timings->ctrla = MICRON_V_ACTIMA_165; + timings->ctrlb = MICRON_V_ACTIMB_165; + } + timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz; + timings->mr = MICRON_V_MR_165; +} +#endif + +/* + * Routine: misc_init_r + * Description: Init ethernet (done here so udelay works) + */ +int misc_init_r(void) +{ + +#ifdef CONFIG_SYS_I2C_OMAP34XX + i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); +#endif + +#if defined(CONFIG_CMD_NET) + setup_net_chip(); +#endif + omap3_evm_get_revision(); + +#if defined(CONFIG_CMD_NET) + reset_net_chip(); +#endif + dieid_num_r(); + + return 0; +} + +/* + * Routine: set_muxconf_regs + * Description: Setting up the configuration Mux registers specific to the + * hardware. Many pins need to be moved from protect to primary + * mode. + */ +void set_muxconf_regs(void) +{ + MUX_EVM(); +} + +#ifdef CONFIG_CMD_NET +/* + * Routine: setup_net_chip + * Description: Setting up the configuration GPMC registers specific to the + * Ethernet hardware. + */ +static void setup_net_chip(void) +{ + struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE; + + /* Configure GPMC registers */ + writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1); + writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2); + writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3); + writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4); + writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5); + writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6); + writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7); + + /* Enable off mode for NWE in PADCONF_GPMC_NWE register */ + writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe); + /* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */ + writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe); + /* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */ + writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00, + &ctrl_base->gpmc_nadv_ale); +} + +/** + * Reset the ethernet chip. + */ +static void reset_net_chip(void) +{ + int ret; + int rst_gpio; + + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) { + rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN1; + } else { + rst_gpio = OMAP3EVM_GPIO_ETH_RST_GEN2; + } + + ret = gpio_request(rst_gpio, ""); + if (ret < 0) { + printf("Unable to get GPIO %d\n", rst_gpio); + return ; + } + + /* Configure as output */ + gpio_direction_output(rst_gpio, 0); + + /* Send a pulse on the GPIO pin */ + gpio_set_value(rst_gpio, 1); + udelay(1); + gpio_set_value(rst_gpio, 0); + udelay(1); + gpio_set_value(rst_gpio, 1); +} + +int board_eth_init(bd_t *bis) +{ + int rc = 0; +#ifdef CONFIG_SMC911X +#define STR_ENV_ETHADDR "ethaddr" + + struct eth_device *dev; + uchar eth_addr[6]; + + rc = smc911x_initialize(0, CONFIG_SMC911X_BASE); + + if (!eth_getenv_enetaddr(STR_ENV_ETHADDR, eth_addr)) { + dev = eth_get_dev_by_index(0); + if (dev) { + eth_setenv_enetaddr(STR_ENV_ETHADDR, dev->enetaddr); + } else { + printf("omap3evm: Couldn't get eth device\n"); + rc = -1; + } + } +#endif + return rc; +} +#endif /* CONFIG_CMD_NET */ + +#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD) +int board_mmc_init(bd_t *bis) +{ + return omap_mmc_init(0, 0, 0, -1, -1); +} +#endif