X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Flwmon5%2Finit.S;fp=qemu%2Froms%2Fu-boot%2Fboard%2Flwmon5%2Finit.S;h=e5207c2b40b5f1a0f26772b49dc0a76c420d39e0;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/board/lwmon5/init.S b/qemu/roms/u-boot/board/lwmon5/init.S
new file mode 100644
index 000000000..e5207c2b4
--- /dev/null
+++ b/qemu/roms/u-boot/board/lwmon5/init.S
@@ -0,0 +1,75 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ *  Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+	.section .bootpg,"ax"
+	.globl tlbtab
+
+tlbtab:
+	tlbtab_start
+
+	/*
+	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+	 * speed up boot process. It is patched after relocation to enable SA_I
+	 */
+	tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G)
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.
+	 * They are dynamically generated in the SPD DDR(2) detection
+	 * routine.
+	 */
+
+#ifdef CONFIG_SYS_INIT_RAM_DCACHE
+	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+	tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
+#endif
+
+	/* TLB-entry for PCI Memory */
+	tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG)
+	tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG)
+	tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG)
+	tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG)
+
+	/* TLB-entry for the FPGA Chip select 2 */
+	tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G)
+
+	/* TLB-entry for the FPGA Chip select 3 */
+	tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G)
+
+	/* TLB-entry for the LIME Controller */
+	tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G)
+	tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G)
+	tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G)
+	tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G)
+
+	/* TLB-entry for Internal Registers & OCM */
+	tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0,  AC_RWX | SA_I)
+
+	/*TLB-entry PCI registers*/
+	tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_RWX | SA_IG)
+
+	/* TLB-entry for peripherals */
+	tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG)
+
+	tlbtab_end