X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Fivm%2Fivm.c;fp=qemu%2Froms%2Fu-boot%2Fboard%2Fivm%2Fivm.c;h=3bdbdd17d315c11bd4464e3da6a11c6ee24c7ea3;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/board/ivm/ivm.c b/qemu/roms/u-boot/board/ivm/ivm.c
new file mode 100644
index 000000000..3bdbdd17d
--- /dev/null
+++ b/qemu/roms/u-boot/board/ivm/ivm.c
@@ -0,0 +1,382 @@
+/*
+ * (C) Copyright 2000, 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Ulrich Lutz, Speech Design GmbH, ulutz@datalab.de.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+#include <commproc.h>
+
+#ifdef CONFIG_STATUS_LED
+# include <status_led.h>
+#endif
+
+/* ------------------------------------------------------------------------- */
+
+static long int dram_size (long int, long int *, long int);
+
+/* ------------------------------------------------------------------------- */
+
+#define	_NOT_USED_	0xFFFFFFFF
+
+/*
+ * 50 MHz SHARC access using UPM A
+ */
+const uint sharc_table[] = {
+	/*
+	 * Single Read. (Offset 0 in UPM RAM)
+	 */
+	0x0FF3FC04, 0x0FF3EC00, 0x7FFFEC04, 0xFFFFEC04,
+	0xFFFFEC05,		/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Read. (Offset 8 in UPM RAM)
+	 */
+	/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Single Write. (Offset 18 in UPM RAM)
+	 */
+	0x0FAFFC04, 0x0FAFEC00, 0x7FFFEC04, 0xFFFFEC04,
+	0xFFFFEC05,		/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Write. (Offset 20 in UPM RAM)
+	 */
+	/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Refresh  (Offset 30 in UPM RAM)
+	 */
+	/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Exception. (Offset 3c in UPM RAM)
+	 */
+	0x7FFFFC07,		/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+
+/*
+ * 50 MHz SDRAM access using UPM B
+ */
+const uint sdram_table[] = {
+	/*
+	 * Single Read. (Offset 0 in UPM RAM)
+	 */
+	0x0E26FC04, 0x11ADFC04, 0xEFBBBC00, 0x1FF77C45,	/* last */
+	_NOT_USED_,
+	/*
+	 * SDRAM Initialization (offset 5 in UPM RAM)
+	 *
+	 * This is no UPM entry point. The following definition uses
+	 * the remaining space to establish an initialization
+	 * sequence, which is executed by a RUN command.
+	 *
+	 */
+	0x1FF77C35, 0xEFEABC34, 0x1FB57C35,	/* last */
+	/*
+	 * Burst Read. (Offset 8 in UPM RAM)
+	 */
+	0x0E26FC04, 0x10ADFC04, 0xF0AFFC00, 0xF0AFFC00,
+	0xF1AFFC00, 0xEFBBBC00, 0x1FF77C45,	/* last */
+	_NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Single Write. (Offset 18 in UPM RAM)
+	 */
+	0x1F27FC04, 0xEEAEBC04, 0x01B93C00, 0x1FF77C45,	/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Burst Write. (Offset 20 in UPM RAM)
+	 */
+	0x0E26BC00, 0x10AD7C00, 0xF0AFFC00, 0xF0AFFC00,
+	0xE1BBBC04, 0x1FF77C45,	/* last */
+	_NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Refresh  (Offset 30 in UPM RAM)
+	 */
+	0x1FF5FC84, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC84,
+	0xFFFFFC05,		/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+	_NOT_USED_, _NOT_USED_, _NOT_USED_, _NOT_USED_,
+	/*
+	 * Exception. (Offset 3c in UPM RAM)
+	 */
+	0x7FFFFC07,		/* last */
+	_NOT_USED_, _NOT_USED_, _NOT_USED_,
+};
+
+/* ------------------------------------------------------------------------- */
+
+
+/*
+ * Check Board Identity:
+ *
+ */
+
+int checkboard (void)
+{
+#ifdef CONFIG_IVMS8
+	puts ("Board: IVMS8\n");
+#endif
+#ifdef CONFIG_IVML24
+	puts ("Board: IVM-L8/24\n");
+#endif
+	return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+phys_size_t initdram (int board_type)
+{
+	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+	volatile memctl8xx_t *memctl = &immr->im_memctl;
+	long int size_b0;
+
+	/* enable SDRAM clock ("switch on" SDRAM) */
+	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_SDRAM_CLKE);	/* GPIO */
+	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_SDRAM_CLKE);	/* active output */
+	immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_SDRAM_CLKE;	/* output */
+	immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_SDRAM_CLKE;	/* assert SDRAM CLKE */
+	udelay (1);
+
+	/*
+	 * Map controller bank 1 for ELIC SACCO
+	 */
+	memctl->memc_or1 = CONFIG_SYS_OR1;
+	memctl->memc_br1 = CONFIG_SYS_BR1;
+
+	/*
+	 * Map controller bank 2 for ELIC EPIC
+	 */
+	memctl->memc_or2 = CONFIG_SYS_OR2;
+	memctl->memc_br2 = CONFIG_SYS_BR2;
+
+	/*
+	 * Configure UPMA for SHARC
+	 */
+	upmconfig (UPMA, (uint *) sharc_table,
+		   sizeof (sharc_table) / sizeof (uint));
+
+#if defined(CONFIG_IVML24)
+	/*
+	 * Map controller bank 4 for HDLC Address space
+	 */
+	memctl->memc_or4 = CONFIG_SYS_OR4;
+	memctl->memc_br4 = CONFIG_SYS_BR4;
+#endif
+
+	/*
+	 * Map controller bank 5 for SHARC
+	 */
+	memctl->memc_or5 = CONFIG_SYS_OR5;
+	memctl->memc_br5 = CONFIG_SYS_BR5;
+
+	memctl->memc_mamr = 0x00001000;
+
+	/*
+	 * Configure UPMB for SDRAM
+	 */
+	upmconfig (UPMB, (uint *) sdram_table,
+		   sizeof (sdram_table) / sizeof (uint));
+
+	memctl->memc_mptpr = CONFIG_SYS_MPTPR_1BK_8K;
+
+	memctl->memc_mar = 0x00000088;
+
+	/*
+	 * Map controller bank 3 to the SDRAM bank at preliminary address.
+	 */
+	memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
+	memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
+
+	memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL;	/* refresh not enabled yet */
+
+	udelay (200);
+	memctl->memc_mcr = 0x80806105;	/* precharge */
+	udelay (1);
+	memctl->memc_mcr = 0x80806106;	/* load mode register */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+	udelay (1);
+	memctl->memc_mcr = 0x80806130;	/* autorefresh */
+
+	memctl->memc_mbmr |= MBMR_PTBE;	/* refresh enabled */
+
+	/*
+	 * Check Bank 0 Memory Size for re-configuration
+	 */
+	size_b0 =
+		dram_size (CONFIG_SYS_MBMR_8COL, (long *) SDRAM_BASE3_PRELIM,
+			   SDRAM_MAX_SIZE);
+
+	memctl->memc_mbmr = CONFIG_SYS_MBMR_8COL | MBMR_PTBE;
+
+	return (size_b0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+
+static long int dram_size (long int mamr_value, long int *base,
+			   long int maxsize)
+{
+	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+	volatile memctl8xx_t *memctl = &immr->im_memctl;
+
+	memctl->memc_mbmr = mamr_value;
+
+	return (get_ram_size (base, maxsize));
+}
+
+/* ------------------------------------------------------------------------- */
+
+void reset_phy (void)
+{
+	immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+
+	/* De-assert Ethernet Powerdown */
+	immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_ETH_POWERDOWN);	/* GPIO */
+	immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_ETH_POWERDOWN);	/* active output */
+	immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_ETH_POWERDOWN;	/* output */
+	immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_ETH_POWERDOWN);	/* Enable PHY power */
+	udelay (1000);
+
+	/*
+	 * RESET is implemented by a positive pulse of at least 1 us
+	 * at the reset pin.
+	 *
+	 * Configure RESET pins for NS DP83843 PHY, and RESET chip.
+	 *
+	 * Note: The RESET pin is high active, but there is an
+	 *       inverter on the SPD823TS board...
+	 */
+	immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_ETH_RESET);
+	immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_ETH_RESET;
+	/* assert RESET signal of PHY */
+	immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_ETH_RESET);
+	udelay (10);
+	/* de-assert RESET signal of PHY */
+	immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_ETH_RESET;
+	udelay (10);
+}
+
+/* ------------------------------------------------------------------------- */
+
+void show_boot_progress (int status)
+{
+#if defined(CONFIG_STATUS_LED)
+# if defined(STATUS_LED_YELLOW)
+	status_led_set (STATUS_LED_YELLOW,
+			(status < 0) ? STATUS_LED_ON : STATUS_LED_OFF);
+# endif	/* STATUS_LED_YELLOW */
+# if defined(STATUS_LED_BOOT)
+	if (status == BOOTSTAGE_ID_DECOMP_IMAGE)
+		status_led_set (STATUS_LED_BOOT, STATUS_LED_OFF);
+# endif	/* STATUS_LED_BOOT */
+#endif /* CONFIG_STATUS_LED */
+}
+
+/* ------------------------------------------------------------------------- */
+
+void ide_set_reset (int on)
+{
+	volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+	int i;
+
+	/*
+	 * Configure PC for IDE Reset Pin
+	 */
+	if (on) {		/* assert RESET */
+		immr->im_ioport.iop_pcdat &= ~(CONFIG_SYS_PC_IDE_RESET);
+
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+		/* 12V Enable output OFF */
+		immr->im_cpm.cp_pbdat &= ~(CONFIG_SYS_PB_12V_ENABLE);
+
+		immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_12V_ENABLE);
+		immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_12V_ENABLE);
+		immr->im_cpm.cp_pbdir |= CONFIG_SYS_PB_12V_ENABLE;
+
+		/* wait 500 ms for the voltage to stabilize */
+		for (i = 0; i < 500; ++i)
+			udelay(1000);
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
+	} else {		/* release RESET */
+#ifdef CONFIG_SYS_PB_12V_ENABLE
+		/* 12V Enable output ON */
+		immr->im_cpm.cp_pbdat |= CONFIG_SYS_PB_12V_ENABLE;
+#endif /* CONFIG_SYS_PB_12V_ENABLE */
+
+#ifdef CONFIG_SYS_PB_IDE_MOTOR
+		/* configure IDE Motor voltage monitor pin as input */
+		immr->im_cpm.cp_pbpar &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+		immr->im_cpm.cp_pbodr &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+		immr->im_cpm.cp_pbdir &= ~(CONFIG_SYS_PB_IDE_MOTOR);
+
+/* wait up to 1 s for the motor voltage to stabilize */
+		for (i = 0; i < 1000; ++i) {
+			if ((immr->im_cpm.cp_pbdat
+					& CONFIG_SYS_PB_IDE_MOTOR) != 0)
+				break;
+			udelay(1000);
+		}
+
+		if (i == 1000) {	/* Timeout */
+			printf("\nWarning: 5V for IDE Motor missing\n");
+#ifdef CONFIG_STATUS_LED
+#ifdef STATUS_LED_YELLOW
+			status_led_set(STATUS_LED_YELLOW, STATUS_LED_ON);
+#endif
+#ifdef STATUS_LED_GREEN
+			status_led_set(STATUS_LED_GREEN, STATUS_LED_OFF);
+#endif
+#endif /* CONFIG_STATUS_LED */
+		}
+#endif /* CONFIG_SYS_PB_IDE_MOTOR */
+
+		immr->im_ioport.iop_pcdat |= CONFIG_SYS_PC_IDE_RESET;
+	}
+
+	/* program port pin as GPIO output */
+	immr->im_ioport.iop_pcpar &= ~(CONFIG_SYS_PC_IDE_RESET);
+	immr->im_ioport.iop_pcso &= ~(CONFIG_SYS_PC_IDE_RESET);
+	immr->im_ioport.iop_pcdir |= CONFIG_SYS_PC_IDE_RESET;
+}
+
+/* ------------------------------------------------------------------------- */