X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Ffreescale%2Fp1_p2_rdb_pc%2FREADME;fp=qemu%2Froms%2Fu-boot%2Fboard%2Ffreescale%2Fp1_p2_rdb_pc%2FREADME;h=f4cc43fbfac130dcc4d58d9817980d23b5678210;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/board/freescale/p1_p2_rdb_pc/README b/qemu/roms/u-boot/board/freescale/p1_p2_rdb_pc/README
new file mode 100644
index 000000000..f4cc43fbf
--- /dev/null
+++ b/qemu/roms/u-boot/board/freescale/p1_p2_rdb_pc/README
@@ -0,0 +1,47 @@
+Overview
+--------
+P1_P2_RDB_PC represents a set of boards including
+    P1020MSBG-PC
+    P1020RDB-PC
+    P1020RDB-PD
+    P1020UTM-PC
+    P1021RDB-PC
+    P1024RDB
+    P1025RDB
+    P2020RDB-PC
+
+They have similar design of P1020RDB but have DDR3 instead of DDR2. P2020RDB-PC
+has 64-bit DDR. All others have 32-bit DDR.
+
+Key features on these boards include:
+    * DDR3
+    * NOR flash
+    * NAND flash (on RDB's only)
+    * SPI flash (on RDB's only)
+    * SDHC/MMC card slot
+    * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
+    * PCIE slot and mini-PCIE slots
+
+As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
+is used to store SPD data. In case of absent or corrupted SPD, falling back
+to timing data embedded in the source code will be used. Raw timing data is
+extracted from DDR chip datasheet. Different speeds of DDR are supported with
+this approach. ODT option is forced to fit this set of boards, again because
+they don't have regular DIMMs.
+
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification
+for writing timing.
+
+VSC firmware Address is defined by default in config file for eTSEC1.
+
+SD width is based off DIP switch. DIP switch is detected on the
+board by reading i2c bus and setting the appropriate mux values.
+
+Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have
+pins multiplexing. QE function needs to be disabled to access Nor Flash and
+CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
+in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
+enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
+
+'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
+'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.