X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Fdavinci%2Fea20%2Fea20.c;fp=qemu%2Froms%2Fu-boot%2Fboard%2Fdavinci%2Fea20%2Fea20.c;h=c4444c7c7f549cd2cb1f24e8cc3619e3a0c24f00;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git

diff --git a/qemu/roms/u-boot/board/davinci/ea20/ea20.c b/qemu/roms/u-boot/board/davinci/ea20/ea20.c
new file mode 100644
index 000000000..c4444c7c7
--- /dev/null
+++ b/qemu/roms/u-boot/board/davinci/ea20/ea20.c
@@ -0,0 +1,339 @@
+/*
+ * (C) Copyright 2010
+ * Stefano Babic, DENX Software Engineering, sbabic@denx.de
+ *
+ * Based on da850evm.c, original Copyrights follow:
+ *
+ * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * Based on da830evm.c. Original Copyrights follow:
+ *
+ * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
+ * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <net.h>
+#include <netdev.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/emif_defs.h>
+#include <asm/arch/emac_defs.h>
+#include <asm/io.h>
+#include <asm/arch/davinci_misc.h>
+#include <asm/gpio.h>
+#include "../../../drivers/video/da8xx-fb.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static const struct da8xx_panel lcd_panel = {
+	/* Casio COM57H531x */
+	.name = "Casio_COM57H531x",
+	.width = 640,
+	.height = 480,
+	.hfp = 12,
+	.hbp = 144,
+	.hsw = 30,
+	.vfp = 10,
+	.vbp = 35,
+	.vsw = 3,
+	.pxl_clk = 25000000,
+	.invert_pxl_clk = 0,
+};
+
+static const struct display_panel disp_panel = {
+	QVGA,
+	16,
+	16,
+	COLOR_ACTIVE,
+};
+
+static const struct lcd_ctrl_config lcd_cfg = {
+	&disp_panel,
+	.ac_bias		= 255,
+	.ac_bias_intrpt		= 0,
+	.dma_burst_sz		= 16,
+	.bpp			= 16,
+	.fdd			= 255,
+	.tft_alt_mode		= 0,
+	.stn_565_mode		= 0,
+	.mono_8bit_mode		= 0,
+	.invert_line_clock	= 1,
+	.invert_frm_clock	= 1,
+	.sync_edge		= 0,
+	.sync_ctrl		= 1,
+	.raster_order		= 0,
+};
+
+/* SPI0 pin muxer settings */
+static const struct pinmux_config spi1_pins[] = {
+	{ pinmux(5), 1, 1 },
+	{ pinmux(5), 1, 2 },
+	{ pinmux(5), 1, 4 },
+	{ pinmux(5), 1, 5 }
+};
+
+/* I2C pin muxer settings */
+static const struct pinmux_config i2c_pins[] = {
+	{ pinmux(4), 2, 2 },
+	{ pinmux(4), 2, 3 }
+};
+
+/* UART0 pin muxer settings */
+static const struct pinmux_config uart_pins[] = {
+	{ pinmux(3), 2, 7 },
+	{ pinmux(3), 2, 6 },
+	{ pinmux(3), 2, 4 },
+	{ pinmux(3), 2, 5 }
+};
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+#define HAS_RMII 1
+static const struct pinmux_config emac_pins[] = {
+	{ pinmux(14), 8, 2 },
+	{ pinmux(14), 8, 3 },
+	{ pinmux(14), 8, 4 },
+	{ pinmux(14), 8, 5 },
+	{ pinmux(14), 8, 6 },
+	{ pinmux(14), 8, 7 },
+	{ pinmux(15), 8, 1 },
+	{ pinmux(4), 8, 0 },
+	{ pinmux(4), 8, 1 }
+};
+#endif
+
+#ifdef CONFIG_NAND_DAVINCI
+const struct pinmux_config nand_pins[] = {
+	{ pinmux(7), 1, 0},	/* CS2 */
+	{ pinmux(7), 0, 1},	/* CS3  in three state*/
+	{ pinmux(7), 1, 4 },	/* EMA_WE */
+	{ pinmux(7), 1, 5 },	/* EMA_OE */
+	{ pinmux(9), 1, 0 },	/* EMA_D[7] */
+	{ pinmux(9), 1, 1 },	/* EMA_D[6] */
+	{ pinmux(9), 1, 2 },	/* EMA_D[5] */
+	{ pinmux(9), 1, 3 },	/* EMA_D[4] */
+	{ pinmux(9), 1, 4 },	/* EMA_D[3] */
+	{ pinmux(9), 1, 5 },	/* EMA_D[2] */
+	{ pinmux(9), 1, 6 },	/* EMA_D[1] */
+	{ pinmux(9), 1, 7 },	/* EMA_D[0] */
+	{ pinmux(12), 1, 5 },	/* EMA_A[2] */
+	{ pinmux(12), 1, 6 },	/* EMA_A[1] */
+	{ pinmux(6), 1, 0 }	/* EMA_CLK */
+};
+#endif
+
+const struct pinmux_config gpio_pins[] = {
+	{ pinmux(13), 8, 0 }, /* GPIO6[15] RESETOUTn on SOM*/
+	{ pinmux(13), 8, 5 }, /* GPIO6[10] U0_SW0 on EA20-00101_2*/
+	{ pinmux(13), 8, 3 }, /* GPIO6[12] U0_SW1 on EA20-00101_2*/
+	{ pinmux(19), 8, 5 }, /* GPIO6[1]  DISP_ON */
+	{ pinmux(14), 8, 1 }  /* GPIO6[6]  LCD_B_PWR*/
+};
+
+const struct pinmux_config lcd_pins[] = {
+	{ pinmux(17), 2, 1 }, /* LCD_D_0 */
+	{ pinmux(17), 2, 0 }, /* LCD_D_1 */
+	{ pinmux(16), 2, 7 }, /* LCD_D_2 */
+	{ pinmux(16), 2, 6 }, /* LCD_D_3 */
+	{ pinmux(16), 2, 5 }, /* LCD_D_4 */
+	{ pinmux(16), 2, 4 }, /* LCD_D_5 */
+	{ pinmux(16), 2, 3 }, /* LCD_D_6 */
+	{ pinmux(16), 2, 2 }, /* LCD_D_7 */
+	{ pinmux(18), 2, 1 }, /* LCD_D_8 */
+	{ pinmux(18), 2, 0 }, /* LCD_D_9 */
+	{ pinmux(17), 2, 7 }, /* LCD_D_10 */
+	{ pinmux(17), 2, 6 }, /* LCD_D_11 */
+	{ pinmux(17), 2, 5 }, /* LCD_D_12 */
+	{ pinmux(17), 2, 4 }, /* LCD_D_13 */
+	{ pinmux(17), 2, 3 }, /* LCD_D_14 */
+	{ pinmux(17), 2, 2 }, /* LCD_D_15 */
+	{ pinmux(18), 2, 6 }, /* LCD_PCLK */
+	{ pinmux(19), 2, 0 }, /* LCD_HSYNC */
+	{ pinmux(19), 2, 1 }, /* LCD_VSYNC */
+	{ pinmux(19), 2, 6 }, /* DA850_NLCD_AC_ENB_CS */
+};
+
+const struct pinmux_config halten_pin[] = {
+	{ pinmux(3),  4, 2 } /* GPIO8[6] HALTEN */
+};
+
+static const struct pinmux_resource pinmuxes[] = {
+#ifdef CONFIG_SPI_FLASH
+	PINMUX_ITEM(spi1_pins),
+#endif
+	PINMUX_ITEM(uart_pins),
+	PINMUX_ITEM(i2c_pins),
+#ifdef CONFIG_NAND_DAVINCI
+	PINMUX_ITEM(nand_pins),
+#endif
+#ifdef CONFIG_VIDEO
+	PINMUX_ITEM(lcd_pins),
+#endif
+};
+
+static const struct lpsc_resource lpsc[] = {
+	{ DAVINCI_LPSC_AEMIF },	/* NAND, NOR */
+	{ DAVINCI_LPSC_SPI1 },	/* Serial Flash */
+	{ DAVINCI_LPSC_EMAC },	/* image download */
+	{ DAVINCI_LPSC_UART0 },	/* console */
+	{ DAVINCI_LPSC_GPIO },
+	{ DAVINCI_LPSC_LCDC }, /* LCD */
+};
+
+int board_early_init_f(void)
+{
+	/* PinMux for GPIO */
+	if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
+		return 1;
+
+	/* Set DISP_ON high to enable LCD output*/
+	gpio_direction_output(97, 1);
+
+	/* Set the RESETOUTn low */
+	gpio_direction_output(111, 0);
+
+	/* Set U0_SW0 low for UART0 as console*/
+	gpio_direction_output(106, 0);
+
+	/* Set U0_SW1 low for UART0 as console*/
+	gpio_direction_output(108, 0);
+
+	/* Set LCD_B_PWR low to power down LCD Backlight*/
+	gpio_direction_output(102, 0);
+
+#ifndef CONFIG_USE_IRQ
+	irq_init();
+#endif
+
+	/*
+	 * NAND CS setup - cycle counts based on da850evm NAND timings in the
+	 * Linux kernel @ 25MHz EMIFA
+	 */
+#ifdef CONFIG_NAND_DAVINCI
+	writel((DAVINCI_ABCR_WSETUP(0) |
+		DAVINCI_ABCR_WSTROBE(1) |
+		DAVINCI_ABCR_WHOLD(0) |
+		DAVINCI_ABCR_RSETUP(0) |
+		DAVINCI_ABCR_RSTROBE(1) |
+		DAVINCI_ABCR_RHOLD(0) |
+		DAVINCI_ABCR_TA(0) |
+		DAVINCI_ABCR_ASIZE_8BIT),
+	       &davinci_emif_regs->ab1cr); /* CS2 */
+#endif
+
+	/*
+	 * Power on required peripherals
+	 * ARM does not have access by default to PSC0 and PSC1
+	 * assuming here that the DSP bootloader has set the IOPU
+	 * such that PSC access is available to ARM
+	 */
+	if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
+		return 1;
+
+	/* setup the SUSPSRC for ARM to control emulation suspend */
+	writel(readl(&davinci_syscfg_regs->suspsrc) &
+	       ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
+		 DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
+		 DAVINCI_SYSCFG_SUSPSRC_UART0),
+	       &davinci_syscfg_regs->suspsrc);
+
+	/* configure pinmux settings */
+	if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
+		return 1;
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+	if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0)
+		return 1;
+
+	davinci_emac_mii_mode_sel(HAS_RMII);
+#endif /* CONFIG_DRIVER_TI_EMAC */
+
+	/* enable the console UART */
+	writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
+		DAVINCI_UART_PWREMU_MGMT_UTRST),
+	       &davinci_uart0_ctrl_regs->pwremu_mgmt);
+
+	/*
+	 * Reconfigure the LCDC priority to the highest to ensure that
+	 * the throughput/latency requirements for the LCDC are met.
+	 */
+	writel(readl(&davinci_syscfg_regs->mstpri[2]) & 0x0fffffff,
+	       &davinci_syscfg_regs->mstpri[2]);
+
+
+	return 0;
+}
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_init(void)
+{
+	/* arch number of the board */
+	gd->bd->bi_arch_number = MACH_TYPE_EA20;
+
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
+
+	da8xx_video_init(&lcd_panel, &lcd_cfg, 16);
+
+	return 0;
+}
+
+#ifdef CONFIG_BOARD_LATE_INIT
+
+int board_late_init(void)
+{
+	unsigned char buf[2];
+	int ret;
+
+	/* PinMux for HALTEN */
+	if (davinci_configure_pin_mux(halten_pin, ARRAY_SIZE(halten_pin)) != 0)
+		return 1;
+
+	/* Set HALTEN to high */
+	gpio_direction_output(134, 1);
+
+	/* Set fixed contrast settings for LCD via I2C potentiometer */
+	buf[0] = 0x00;
+	buf[1] = 0xd7;
+	ret = i2c_write(0x2e, 6, 1, buf, 2);
+	if (ret)
+		puts("\nContrast Settings FAILED\n");
+
+	/* Set LCD_B_PWR high to power up LCD Backlight*/
+	gpio_set_value(102, 1);
+	return 0;
+}
+#endif /* CONFIG_BOARD_LATE_INIT */
+
+#ifdef CONFIG_DRIVER_TI_EMAC
+
+/*
+ * Initializes on-board ethernet controllers.
+ */
+int board_eth_init(bd_t *bis)
+{
+	if (!davinci_emac_initialize()) {
+		printf("Error: Ethernet init failed!\n");
+		return -1;
+	}
+
+	/*
+	 * This board has a RMII PHY. However, the MDC line on the SOM
+	 * must not be disabled (there is no MII PHY on the
+	 * baseboard) via the GPIO2[6], because this pin
+	 * disables at the same time the SPI flash.
+	 */
+
+	return 0;
+}
+#endif /* CONFIG_DRIVER_TI_EMAC */