X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2Fd-link%2Fdns325%2Fkwbimage.cfg;fp=qemu%2Froms%2Fu-boot%2Fboard%2Fd-link%2Fdns325%2Fkwbimage.cfg;h=b69c1df5c0fc161a0046d10b4ff89fd33f6e4748;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/board/d-link/dns325/kwbimage.cfg b/qemu/roms/u-boot/board/d-link/dns325/kwbimage.cfg new file mode 100644 index 000000000..b69c1df5c --- /dev/null +++ b/qemu/roms/u-boot/board/d-link/dns325/kwbimage.cfg @@ -0,0 +1,192 @@ +# +# Copyright (C) 2011 +# Stefan Herbrechtsmeier +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor +# Written-by: Prafulla Wadaskar +# +# SPDX-License-Identifier: GPL-2.0+ +# +# Refer doc/README.kwbimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30, 3120 DDR2 clks refresh rate +# bit23-14: 0 required +# bit24: 1, enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: 0 required +# bit31-30: 0b01 required + +DATA 0xFFD01404 0x39543000 # DDR Controller Control Low +# bit3-0: 0 required +# bit4: 0, addr/cmd in smame cycle +# bit5: 0, clk is driven during self refresh, we don't care for APX +# bit6: 0, use recommended falling edge of clk for addr/cmd +# bit11-7: 0 required +# bit12: 1 required +# bit13: 1 required +# bit14: 0, input buffer always powered up +# bit17-15: 0 required +# bit18: 1, cpu lock transaction enabled +# bit19: 0 required +# bit23-20: 5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 9, CL+4, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0, no additional STARTBURST delay + +DATA 0xFFD01408 0x22125451 # DDR Timing (Low) +# bit3-0: 1, 18 cycle tRAS (tRAS[3-0]) +# bit7-4: 5, 6 cycle tRCD +# bit11-8: 4, 5 cyle tRP +# bit15-12: 5, 6 cyle tWR +# bit19-16: 2, 3 cyle tWTR +# bit20: 1, 18 cycle tRAS (tRAS[4]) +# bit23-21: 0 required +# bit27-24: 2, 3 cycle tRRD +# bit31-28: 2, 3 cyle tRTP + +DATA 0xFFD0140C 0x00000833 # DDR Timing (High) +# bit6-0: 0x33, 33 cycle tRFC +# bit8-7: 0, 1 cycle tR2R +# bit10-9: 0, 1 cyle tR2W +# bit12-11: 1, 2 cylce tW2W +# bit31-13: 0 required + +DATA 0xFFD01410 0x0000000c # DDR Address Control +# bit1-0: 0, Cs0width=x8 +# bit3-2: 3, Cs0size=1Gb +# bit5-4: 0, Cs1width=nonexistent +# bit7-6: 0, Cs1size=nonexistent +# bit9-8: 0, Cs2width=nonexistent +# bit11-10: 0, Cs2size=nonexistent +# bit13-12: 0, Cs3width=nonexistent +# bit15-14: 0, Cs3size=nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OPEn=OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0, Cmd=Normal SDRAM Mode +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000C52 # DDR Mode +# bit2-0: 2, Burst Length (2 required) +# bit3: 0, Burst Type (0 required) +# bit6-4: 5, CAS Latency (CL) 5 +# bit7: 0, (Test Mode) Normal operation +# bit8: 0, (Reset DLL) Normal operation +# bit11-9: 0, Write recovery for auto-precharge (3 required ??) +# bit12: 0, Fast Active power down exit time (0 required) +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DRAM DLL enabled +# bit1: 0, DRAM drive strength normal +# bit2: 0, ODT control Rtt[0] (Rtt=2, 150 ohm termination) +# bit5-3: 0 required +# bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination) +# bit9-7: 0 required +# bit10: 0, differential DQS enabled +# bit11: 0 required +# bit12: 0, DRAM output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F17F # DDR Controller Control High +# bit2-0: 0x7 required +# bit3: 1, MBUS Burst Chop disabled +# bit6-4: 0x7 required +# bit7: 0 required +# bit8: 1, add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9: 0, no half clock cycle addition to dataout +# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit11: 0, 1/4 clock cycle skew disabled for write mesh +# bit15-12: 0xf required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing +# bit3-0: 0 required +# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal +# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal +# bit31-20: 0 required + +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing +# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal +# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal +# bit31-16: 0 required + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 0x0, CS0 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x0f, Size (i.e. 256MB) + +DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb +DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 1, CS1 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x0f, Size (i.e. 256MB) + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) +# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM +# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM +# bit15-8: 0 required +# bit19-16: 0b0011, (write) M_ODT[0] is asserted during write to DRAM CS0 and CS1 +# bit23-20: 0b0000, (write) M_ODT[1] is not asserted during write to DRAM +# bit31-24: 0 required + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register +# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register +# bit31-4 0 required + +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control +# bit3-0: 0b0011, internal ODT is asserted during read from DRAM bank 0-1 +# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-4 +# bit9-8: 0, Internal ODT assertion is controlled by fiels +# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm +# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm +# bit14: 1, M_STARTBURST_IN ODT enabled +# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values +# bit20-16: 0, Pad N channel driving strength for ODT +# bit25-21: 0, Pad P channel driving strength for ODT +# bit31-26: 0 required + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit0: 1, enable DDR init upon this register write +# bit31-1: 0, required + +# End of Header extension +DATA 0x0 0x0