X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=qemu%2Froms%2Fu-boot%2Fboard%2FMarvell%2Fdb64460%2Fsdram_init.c;fp=qemu%2Froms%2Fu-boot%2Fboard%2FMarvell%2Fdb64460%2Fsdram_init.c;h=71c2d9eb329b7758f06d5bd3c52f46893a8a73b4;hb=e44e3482bdb4d0ebde2d8b41830ac2cdb07948fb;hp=0000000000000000000000000000000000000000;hpb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;p=kvmfornfv.git diff --git a/qemu/roms/u-boot/board/Marvell/db64460/sdram_init.c b/qemu/roms/u-boot/board/Marvell/db64460/sdram_init.c new file mode 100644 index 000000000..71c2d9eb3 --- /dev/null +++ b/qemu/roms/u-boot/board/Marvell/db64460/sdram_init.c @@ -0,0 +1,1950 @@ +/* + * (C) Copyright 2001 + * Josh Huber , Mission Critical Linux, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/************************************************************************* + * adaption for the Marvell DB64460 Board + * Ingo Assmus (ingo.assmus@keymile.com) + ************************************************************************/ + + +/* sdram_init.c - automatic memory sizing */ + +#include +#include <74xx_7xx.h> +#include "../include/memory.h" +#include "../include/pci.h" +#include "../include/mv_gen_reg.h" +#include + +#include "eth.h" +#include "mpsc.h" +#include "../common/i2c.h" +#include "64460.h" +#include "mv_regs.h" + +DECLARE_GLOBAL_DATA_PTR; + +#define MAP_PCI + +int set_dfcdlInit (void); /* setup delay line of Mv64460 */ +int mvDmaIsChannelActive (int); +int mvDmaSetMemorySpace (ulong, ulong, ulong, ulong, ulong); +int mvDmaTransfer (int, ulong, ulong, ulong, ulong); + +/* ------------------------------------------------------------------------- */ + +int +memory_map_bank (unsigned int bankNo, + unsigned int bankBase, unsigned int bankLength) +{ +#ifdef MAP_PCI + PCI_HOST host; +#endif + + + if (bankLength > 0) { + debug("mapping bank %d at %08x - %08x\n", + bankNo, bankBase, bankBase + bankLength - 1); + } else { + debug("unmapping bank %d\n", bankNo); + } + + memoryMapBank (bankNo, bankBase, bankLength); + +#ifdef MAP_PCI + for (host = PCI_HOST0; host <= PCI_HOST1; host++) { + const int features = + PREFETCH_ENABLE | + DELAYED_READ_ENABLE | + AGGRESSIVE_PREFETCH | + READ_LINE_AGGRESSIVE_PREFETCH | + READ_MULTI_AGGRESSIVE_PREFETCH | + MAX_BURST_4 | PCI_NO_SWAP; + + pciMapMemoryBank (host, bankNo, bankBase, bankLength); + + pciSetRegionSnoopMode (host, bankNo, PCI_SNOOP_WB, bankBase, + bankLength); + + pciSetRegionFeatures (host, bankNo, features, bankBase, + bankLength); + } +#endif + return 0; +} + +#define GB (1 << 30) + +/* much of this code is based on (or is) the code in the pip405 port */ +/* thanks go to the authors of said port - Josh */ + +/* structure to store the relevant information about an sdram bank */ +typedef struct sdram_info { + uchar drb_size; + uchar registered, ecc; + uchar tpar; + uchar tras_clocks; + uchar burst_len; + uchar banks, slot; +} sdram_info_t; + +/* Typedefs for 'gtAuxilGetDIMMinfo' function */ + +typedef enum _memoryType { SDRAM, DDR } MEMORY_TYPE; + +typedef enum _voltageInterface { TTL_5V_TOLERANT, LVTTL, HSTL_1_5V, + SSTL_3_3V, SSTL_2_5V, VOLTAGE_UNKNOWN, +} VOLTAGE_INTERFACE; + +typedef enum _max_CL_supported_DDR { DDR_CL_1 = 1, DDR_CL_1_5 = 2, DDR_CL_2 = + 4, DDR_CL_2_5 = 8, DDR_CL_3 = 16, DDR_CL_3_5 = + 32, DDR_CL_FAULT } MAX_CL_SUPPORTED_DDR; +typedef enum _max_CL_supported_SD { SD_CL_1 = + 1, SD_CL_2, SD_CL_3, SD_CL_4, SD_CL_5, SD_CL_6, SD_CL_7, + SD_FAULT } MAX_CL_SUPPORTED_SD; + + +/* SDRAM/DDR information struct */ +typedef struct _gtMemoryDimmInfo { + MEMORY_TYPE memoryType; + unsigned int numOfRowAddresses; + unsigned int numOfColAddresses; + unsigned int numOfModuleBanks; + unsigned int dataWidth; + VOLTAGE_INTERFACE voltageInterface; + unsigned int errorCheckType; /* ECC , PARITY.. */ + unsigned int sdramWidth; /* 4,8,16 or 32 */ ; + unsigned int errorCheckDataWidth; /* 0 - no, 1 - Yes */ + unsigned int minClkDelay; + unsigned int burstLengthSupported; + unsigned int numOfBanksOnEachDevice; + unsigned int suportedCasLatencies; + unsigned int RefreshInterval; + unsigned int maxCASlatencySupported_LoP; /* LoP left of point (measured in ns) */ + unsigned int maxCASlatencySupported_RoP; /* RoP right of point (measured in ns) */ + MAX_CL_SUPPORTED_DDR maxClSupported_DDR; + MAX_CL_SUPPORTED_SD maxClSupported_SD; + unsigned int moduleBankDensity; + /* module attributes (true for yes) */ + bool bufferedAddrAndControlInputs; + bool registeredAddrAndControlInputs; + bool onCardPLL; + bool bufferedDQMBinputs; + bool registeredDQMBinputs; + bool differentialClockInput; + bool redundantRowAddressing; + + /* module general attributes */ + bool suportedAutoPreCharge; + bool suportedPreChargeAll; + bool suportedEarlyRasPreCharge; + bool suportedWrite1ReadBurst; + bool suported5PercentLowVCC; + bool suported5PercentUpperVCC; + /* module timing parameters */ + unsigned int minRasToCasDelay; + unsigned int minRowActiveRowActiveDelay; + unsigned int minRasPulseWidth; + unsigned int minRowPrechargeTime; /* measured in ns */ + + int addrAndCommandHoldTime; /* LoP left of point (measured in ns) */ + int addrAndCommandSetupTime; /* (measured in ns/100) */ + int dataInputSetupTime; /* LoP left of point (measured in ns) */ + int dataInputHoldTime; /* LoP left of point (measured in ns) */ +/* tAC times for highest 2nd and 3rd highest CAS Latency values */ + unsigned int clockToDataOut_LoP; /* LoP left of point (measured in ns) */ + unsigned int clockToDataOut_RoP; /* RoP right of point (measured in ns) */ + unsigned int clockToDataOutMinus1_LoP; /* LoP left of point (measured in ns) */ + unsigned int clockToDataOutMinus1_RoP; /* RoP right of point (measured in ns) */ + unsigned int clockToDataOutMinus2_LoP; /* LoP left of point (measured in ns) */ + unsigned int clockToDataOutMinus2_RoP; /* RoP right of point (measured in ns) */ + + unsigned int minimumCycleTimeAtMaxCasLatancy_LoP; /* LoP left of point (measured in ns) */ + unsigned int minimumCycleTimeAtMaxCasLatancy_RoP; /* RoP right of point (measured in ns) */ + + unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_LoP; /* LoP left of point (measured in ns) */ + unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_RoP; /* RoP right of point (measured in ns) */ + + unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_LoP; /* LoP left of point (measured in ns) */ + unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_RoP; /* RoP right of point (measured in ns) */ + + /* Parameters calculated from + the extracted DIMM information */ + unsigned int size; + unsigned int deviceDensity; /* 16,64,128,256 or 512 Mbit */ + unsigned int numberOfDevices; + uchar drb_size; /* DRAM size in n*64Mbit */ + uchar slot; /* Slot Number this module is inserted in */ + uchar spd_raw_data[128]; /* Content of SPD-EEPROM copied 1:1 */ +#ifdef DEBUG + uchar manufactura[8]; /* Content of SPD-EEPROM Byte 64-71 */ + uchar modul_id[18]; /* Content of SPD-EEPROM Byte 73-90 */ + uchar vendor_data[27]; /* Content of SPD-EEPROM Byte 99-125 */ + unsigned long modul_serial_no; /* Content of SPD-EEPROM Byte 95-98 */ + unsigned int manufac_date; /* Content of SPD-EEPROM Byte 93-94 */ + unsigned int modul_revision; /* Content of SPD-EEPROM Byte 91-92 */ + uchar manufac_place; /* Content of SPD-EEPROM Byte 72 */ + +#endif +} AUX_MEM_DIMM_INFO; + + +/* + * translate ns.ns/10 coding of SPD timing values + * into 10 ps unit values + */ +static inline unsigned short NS10to10PS (unsigned char spd_byte) +{ + unsigned short ns, ns10; + + /* isolate upper nibble */ + ns = (spd_byte >> 4) & 0x0F; + /* isolate lower nibble */ + ns10 = (spd_byte & 0x0F); + + return (ns * 100 + ns10 * 10); +} + +/* + * translate ns coding of SPD timing values + * into 10 ps unit values + */ +static inline unsigned short NSto10PS (unsigned char spd_byte) +{ + return (spd_byte * 100); +} + +/* This code reads the SPD chip on the sdram and populates + * the array which is passed in with the relevant information */ +/* static int check_dimm(uchar slot, AUX_MEM_DIMM_INFO *info) */ +static int check_dimm (uchar slot, AUX_MEM_DIMM_INFO * dimmInfo) +{ + unsigned long spd_checksum; + +#ifdef ZUMA_NTL + /* zero all the values */ + memset (info, 0, sizeof (*info)); + +/* + if (!slot) { + info->slot = 0; + info->banks = 1; + info->registered = 0; + info->drb_size = 16;*/ /* 16 - 256MBit, 32 - 512MBit */ +/* info->tpar = 3; + info->tras_clocks = 5; + info->burst_len = 4; +*/ +#ifdef CONFIG_MV64460_ECC + /* check for ECC/parity [0 = none, 1 = parity, 2 = ecc] */ + dimmInfo->errorCheckType = 2; +/* info->ecc = 2;*/ +#endif +} + +return 0; + +#else + uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR; + int ret; + unsigned int i, j, density = 1; + +#ifdef DEBUG + unsigned int k; +#endif + unsigned int rightOfPoint = 0, leftOfPoint = 0, mult, div, time_tmp; + int sign = 1, shift, maskLeftOfPoint, maskRightOfPoint; + uchar supp_cal, cal_val; + ulong memclk, tmemclk; + ulong tmp; + uchar trp_clocks = 0, tras_clocks; + uchar data[128]; + + memclk = gd->bus_clk; + tmemclk = 1000000000 / (memclk / 100); /* in 10 ps units */ + + debug("before i2c read\n"); + + ret = i2c_read (addr, 0, 1, data, 128); + + debug("after i2c read\n"); + + /* zero all the values */ + memset (dimmInfo, 0, sizeof (*dimmInfo)); + + /* copy the SPD content 1:1 into the dimmInfo structure */ + for (i = 0; i <= 127; i++) { + dimmInfo->spd_raw_data[i] = data[i]; + } + + if (ret) { + debug("No DIMM in slot %d [err = %x]\n", slot, ret); + return 0; + } else + dimmInfo->slot = slot; /* start to fill up dimminfo for this "slot" */ + +#ifdef CONFIG_SYS_DISPLAY_DIMM_SPD_CONTENT + + for (i = 0; i <= 127; i++) { + printf ("SPD-EEPROM Byte %3d = %3x (%3d)\n", i, data[i], + data[i]); + } + +#endif +#ifdef DEBUG +/* find Manufactura of Dimm Module */ + for (i = 0; i < sizeof (dimmInfo->manufactura); i++) { + dimmInfo->manufactura[i] = data[64 + i]; + } + printf ("\nThis RAM-Module is produced by: %s\n", + dimmInfo->manufactura); + +/* find Manul-ID of Dimm Module */ + for (i = 0; i < sizeof (dimmInfo->modul_id); i++) { + dimmInfo->modul_id[i] = data[73 + i]; + } + printf ("The Module-ID of this RAM-Module is: %s\n", + dimmInfo->modul_id); + +/* find Vendor-Data of Dimm Module */ + for (i = 0; i < sizeof (dimmInfo->vendor_data); i++) { + dimmInfo->vendor_data[i] = data[99 + i]; + } + printf ("Vendor Data of this RAM-Module is: %s\n", + dimmInfo->vendor_data); + +/* find modul_serial_no of Dimm Module */ + dimmInfo->modul_serial_no = (*((unsigned long *) (&data[95]))); + printf ("Serial No. of this RAM-Module is: %ld (%lx)\n", + dimmInfo->modul_serial_no, dimmInfo->modul_serial_no); + +/* find Manufac-Data of Dimm Module */ + dimmInfo->manufac_date = (*((unsigned int *) (&data[93]))); + printf ("Manufactoring Date of this RAM-Module is: %d.%d\n", data[93], data[94]); /*dimmInfo->manufac_date */ + +/* find modul_revision of Dimm Module */ + dimmInfo->modul_revision = (*((unsigned int *) (&data[91]))); + printf ("Module Revision of this RAM-Module is: %d.%d\n", data[91], data[92]); /* dimmInfo->modul_revision */ + +/* find manufac_place of Dimm Module */ + dimmInfo->manufac_place = (*((unsigned char *) (&data[72]))); + printf ("manufac_place of this RAM-Module is: %d\n", + dimmInfo->manufac_place); + +#endif + +/*------------------------------------------------------------------------------------------------------------------------------*/ +/* calculate SPD checksum */ +/*------------------------------------------------------------------------------------------------------------------------------*/ + spd_checksum = 0; + + for (i = 0; i <= 62; i++) { + spd_checksum += data[i]; + } + + if ((spd_checksum & 0xff) != data[63]) { + printf ("### Error in SPD Checksum !!! Is_value: %2x should value %2x\n", (unsigned int) (spd_checksum & 0xff), data[63]); + hang (); + } + + else + printf ("SPD Checksum ok!\n"); + + +/*------------------------------------------------------------------------------------------------------------------------------*/ + for (i = 2; i <= 35; i++) { + switch (i) { + case 2: /* Memory type (DDR / SDRAM) */ + dimmInfo->memoryType = (data[i] == 0x7) ? DDR : SDRAM; +#ifdef DEBUG + if (dimmInfo->memoryType == 0) + debug + ("Dram_type in slot %d is: SDRAM\n", + dimmInfo->slot); + if (dimmInfo->memoryType == 1) + debug + ("Dram_type in slot %d is: DDRAM\n", + dimmInfo->slot); +#endif + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 3: /* Number Of Row Addresses */ + dimmInfo->numOfRowAddresses = data[i]; + debug + ("Module Number of row addresses: %d\n", + dimmInfo->numOfRowAddresses); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 4: /* Number Of Column Addresses */ + dimmInfo->numOfColAddresses = data[i]; + debug + ("Module Number of col addresses: %d\n", + dimmInfo->numOfColAddresses); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 5: /* Number Of Module Banks */ + dimmInfo->numOfModuleBanks = data[i]; + debug + ("Number of Banks on Mod. : %d\n", + dimmInfo->numOfModuleBanks); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 6: /* Data Width */ + dimmInfo->dataWidth = data[i]; + debug + ("Module Data Width: %d\n", + dimmInfo->dataWidth); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 8: /* Voltage Interface */ + switch (data[i]) { + case 0x0: + dimmInfo->voltageInterface = TTL_5V_TOLERANT; + debug + ("Module is TTL_5V_TOLERANT\n"); + break; + case 0x1: + dimmInfo->voltageInterface = LVTTL; + debug + ("Module is LVTTL\n"); + break; + case 0x2: + dimmInfo->voltageInterface = HSTL_1_5V; + debug + ("Module is TTL_5V_TOLERANT\n"); + break; + case 0x3: + dimmInfo->voltageInterface = SSTL_3_3V; + debug + ("Module is HSTL_1_5V\n"); + break; + case 0x4: + dimmInfo->voltageInterface = SSTL_2_5V; + debug + ("Module is SSTL_2_5V\n"); + break; + default: + dimmInfo->voltageInterface = VOLTAGE_UNKNOWN; + debug + ("Module is VOLTAGE_UNKNOWN\n"); + break; + } + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 9: /* Minimum Cycle Time At Max CasLatancy */ + shift = (dimmInfo->memoryType == DDR) ? 4 : 2; + mult = (dimmInfo->memoryType == DDR) ? 10 : 25; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf : 0x03; + leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; + rightOfPoint = (data[i] & maskRightOfPoint) * mult; + dimmInfo->minimumCycleTimeAtMaxCasLatancy_LoP = + leftOfPoint; + dimmInfo->minimumCycleTimeAtMaxCasLatancy_RoP = + rightOfPoint; + debug + ("Minimum Cycle Time At Max CasLatancy: %d.%d [ns]\n", + leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 10: /* Clock To Data Out */ + div = (dimmInfo->memoryType == DDR) ? 100 : 10; + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / div; + rightOfPoint = time_tmp % div; + dimmInfo->clockToDataOut_LoP = leftOfPoint; + dimmInfo->clockToDataOut_RoP = rightOfPoint; + debug("Clock To Data Out: %d.%2d [ns]\n", leftOfPoint, rightOfPoint); /*dimmInfo->clockToDataOut */ + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + +/*#ifdef CONFIG_ECC */ + case 11: /* Error Check Type */ + dimmInfo->errorCheckType = data[i]; + debug + ("Error Check Type (0=NONE): %d\n", + dimmInfo->errorCheckType); + break; +/* #endif */ +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 12: /* Refresh Interval */ + dimmInfo->RefreshInterval = data[i]; + debug + ("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n", + dimmInfo->RefreshInterval); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 13: /* Sdram Width */ + dimmInfo->sdramWidth = data[i]; + debug + ("Sdram Width: %d\n", + dimmInfo->sdramWidth); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 14: /* Error Check Data Width */ + dimmInfo->errorCheckDataWidth = data[i]; + debug + ("Error Check Data Width: %d\n", + dimmInfo->errorCheckDataWidth); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 15: /* Minimum Clock Delay */ + dimmInfo->minClkDelay = data[i]; + debug + ("Minimum Clock Delay: %d\n", + dimmInfo->minClkDelay); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 16: /* Burst Length Supported */ + /******-******-******-******* + * bit3 | bit2 | bit1 | bit0 * + *******-******-******-******* + burst length = * 8 | 4 | 2 | 1 * + ***************************** + + If for example bit0 and bit2 are set, the burst + length supported are 1 and 4. */ + + dimmInfo->burstLengthSupported = data[i]; +#ifdef DEBUG + debug + ("Burst Length Supported: "); + if (dimmInfo->burstLengthSupported & 0x01) + debug("1, "); + if (dimmInfo->burstLengthSupported & 0x02) + debug("2, "); + if (dimmInfo->burstLengthSupported & 0x04) + debug("4, "); + if (dimmInfo->burstLengthSupported & 0x08) + debug("8, "); + debug(" Bit \n"); +#endif + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 17: /* Number Of Banks On Each Device */ + dimmInfo->numOfBanksOnEachDevice = data[i]; + debug + ("Number Of Banks On Each Chip: %d\n", + dimmInfo->numOfBanksOnEachDevice); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 18: /* Suported Cas Latencies */ + + /* DDR: + *******-******-******-******-******-******-******-******* + * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 * + *******-******-******-******-******-******-******-******* + CAS = * TBD | TBD | 3.5 | 3 | 2.5 | 2 | 1.5 | 1 * + ********************************************************* + SDRAM: + *******-******-******-******-******-******-******-******* + * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 * + *******-******-******-******-******-******-******-******* + CAS = * TBD | 7 | 6 | 5 | 4 | 3 | 2 | 1 * + ********************************************************/ + dimmInfo->suportedCasLatencies = data[i]; +#ifdef DEBUG + debug + ("Suported Cas Latencies: (CL) "); + if (dimmInfo->memoryType == 0) { /* SDRAM */ + for (k = 0; k <= 7; k++) { + if (dimmInfo-> + suportedCasLatencies & (1 << k)) + debug + ("%d, ", + k + 1); + } + + } else { /* DDR-RAM */ + + if (dimmInfo->suportedCasLatencies & 1) + debug("1, "); + if (dimmInfo->suportedCasLatencies & 2) + debug("1.5, "); + if (dimmInfo->suportedCasLatencies & 4) + debug("2, "); + if (dimmInfo->suportedCasLatencies & 8) + debug("2.5, "); + if (dimmInfo->suportedCasLatencies & 16) + debug("3, "); + if (dimmInfo->suportedCasLatencies & 32) + debug("3.5, "); + + } + debug("\n"); +#endif + /* Calculating MAX CAS latency */ + for (j = 7; j > 0; j--) { + if (((dimmInfo-> + suportedCasLatencies >> j) & 0x1) == + 1) { + switch (dimmInfo->memoryType) { + case DDR: + /* CAS latency 1, 1.5, 2, 2.5, 3, 3.5 */ + switch (j) { + case 7: + debug + ("Max. Cas Latencies (DDR): ERROR !!!\n"); + dimmInfo-> + maxClSupported_DDR + = + DDR_CL_FAULT; + hang (); + break; + case 6: + debug + ("Max. Cas Latencies (DDR): ERROR !!!\n"); + dimmInfo-> + maxClSupported_DDR + = + DDR_CL_FAULT; + hang (); + break; + case 5: + debug + ("Max. Cas Latencies (DDR): 3.5 clk's\n"); + dimmInfo-> + maxClSupported_DDR + = DDR_CL_3_5; + break; + case 4: + debug + ("Max. Cas Latencies (DDR): 3 clk's \n"); + dimmInfo-> + maxClSupported_DDR + = DDR_CL_3; + break; + case 3: + debug + ("Max. Cas Latencies (DDR): 2.5 clk's \n"); + dimmInfo-> + maxClSupported_DDR + = DDR_CL_2_5; + break; + case 2: + debug + ("Max. Cas Latencies (DDR): 2 clk's \n"); + dimmInfo-> + maxClSupported_DDR + = DDR_CL_2; + break; + case 1: + debug + ("Max. Cas Latencies (DDR): 1.5 clk's \n"); + dimmInfo-> + maxClSupported_DDR + = DDR_CL_1_5; + break; + } + + /* ronen - in case we have a DIMM with minimumCycleTimeAtMaxCasLatancy + lower then our SDRAM cycle count, we won't be able to support this CAL + and we will have to use lower CAL. (minus - means from 3.0 to 2.5) */ + if ((dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_LoP + < + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP) + || + ((dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_LoP + == + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP) + && (dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_RoP + < + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP))) + { + dimmInfo-> + maxClSupported_DDR + = + dimmInfo-> + maxClSupported_DDR + >> 1; + debug + ("*** Change actual Cas Latencies cause of minimumCycleTime n"); + } + /* ronen - checkif the Dimm frequency compared to the Sysclock. */ + if ((dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_LoP + > + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP) + || + ((dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_LoP + == + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_LOP) + && (dimmInfo-> + minimumCycleTimeAtMaxCasLatancy_RoP + > + CONFIG_SYS_DDR_SDRAM_CYCLE_COUNT_ROP))) + { + printf ("*********************************************************\n"); + printf ("*** sysClock is higher than SDRAM's allowed frequency ***\n"); + printf ("*********************************************************\n"); + hang (); + } + + dimmInfo-> + maxCASlatencySupported_LoP + = + 1 + + (int) (5 * j / 10); + if (((5 * j) % 10) != 0) + dimmInfo-> + maxCASlatencySupported_RoP + = 5; + else + dimmInfo-> + maxCASlatencySupported_RoP + = 0; + debug + ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n", + dimmInfo-> + maxCASlatencySupported_LoP, + dimmInfo-> + maxCASlatencySupported_RoP); + break; + case SDRAM: + /* CAS latency 1, 2, 3, 4, 5, 6, 7 */ + dimmInfo->maxClSupported_SD = j; /* Cas Latency DDR-RAM Coded */ + debug + ("Max. Cas Latencies (SD): %d\n", + dimmInfo-> + maxClSupported_SD); + dimmInfo-> + maxCASlatencySupported_LoP + = j; + dimmInfo-> + maxCASlatencySupported_RoP + = 0; + debug + ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n", + dimmInfo-> + maxCASlatencySupported_LoP, + dimmInfo-> + maxCASlatencySupported_RoP); + break; + } + break; + } + } + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 21: /* Buffered Address And Control Inputs */ + debug("\nModul Attributes (SPD Byte 21): \n"); + dimmInfo->bufferedAddrAndControlInputs = + data[i] & BIT0; + dimmInfo->registeredAddrAndControlInputs = + (data[i] & BIT1) >> 1; + dimmInfo->onCardPLL = (data[i] & BIT2) >> 2; + dimmInfo->bufferedDQMBinputs = (data[i] & BIT3) >> 3; + dimmInfo->registeredDQMBinputs = + (data[i] & BIT4) >> 4; + dimmInfo->differentialClockInput = + (data[i] & BIT5) >> 5; + dimmInfo->redundantRowAddressing = + (data[i] & BIT6) >> 6; +#ifdef DEBUG + if (dimmInfo->bufferedAddrAndControlInputs == 1) + debug + (" - Buffered Address/Control Input: Yes \n"); + else + debug + (" - Buffered Address/Control Input: No \n"); + + if (dimmInfo->registeredAddrAndControlInputs == 1) + debug + (" - Registered Address/Control Input: Yes \n"); + else + debug + (" - Registered Address/Control Input: No \n"); + + if (dimmInfo->onCardPLL == 1) + debug + (" - On-Card PLL (clock): Yes \n"); + else + debug + (" - On-Card PLL (clock): No \n"); + + if (dimmInfo->bufferedDQMBinputs == 1) + debug + (" - Bufferd DQMB Inputs: Yes \n"); + else + debug + (" - Bufferd DQMB Inputs: No \n"); + + if (dimmInfo->registeredDQMBinputs == 1) + debug + (" - Registered DQMB Inputs: Yes \n"); + else + debug + (" - Registered DQMB Inputs: No \n"); + + if (dimmInfo->differentialClockInput == 1) + debug + (" - Differential Clock Input: Yes \n"); + else + debug + (" - Differential Clock Input: No \n"); + + if (dimmInfo->redundantRowAddressing == 1) + debug + (" - redundant Row Addressing: Yes \n"); + else + debug + (" - redundant Row Addressing: No \n"); + +#endif + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 22: /* Suported AutoPreCharge */ + debug("\nModul Attributes (SPD Byte 22): \n"); + dimmInfo->suportedEarlyRasPreCharge = data[i] & BIT0; + dimmInfo->suportedAutoPreCharge = + (data[i] & BIT1) >> 1; + dimmInfo->suportedPreChargeAll = + (data[i] & BIT2) >> 2; + dimmInfo->suportedWrite1ReadBurst = + (data[i] & BIT3) >> 3; + dimmInfo->suported5PercentLowVCC = + (data[i] & BIT4) >> 4; + dimmInfo->suported5PercentUpperVCC = + (data[i] & BIT5) >> 5; +#ifdef DEBUG + if (dimmInfo->suportedEarlyRasPreCharge == 1) + debug + (" - Early Ras Precharge: Yes \n"); + else + debug + (" - Early Ras Precharge: No \n"); + + if (dimmInfo->suportedAutoPreCharge == 1) + debug + (" - AutoPreCharge: Yes \n"); + else + debug + (" - AutoPreCharge: No \n"); + + if (dimmInfo->suportedPreChargeAll == 1) + debug + (" - Precharge All: Yes \n"); + else + debug + (" - Precharge All: No \n"); + + if (dimmInfo->suportedWrite1ReadBurst == 1) + debug + (" - Write 1/ReadBurst: Yes \n"); + else + debug + (" - Write 1/ReadBurst: No \n"); + + if (dimmInfo->suported5PercentLowVCC == 1) + debug + (" - lower VCC tolerance: 5 Percent \n"); + else + debug + (" - lower VCC tolerance: 10 Percent \n"); + + if (dimmInfo->suported5PercentUpperVCC == 1) + debug + (" - upper VCC tolerance: 5 Percent \n"); + else + debug + (" - upper VCC tolerance: 10 Percent \n"); + +#endif + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 23: /* Minimum Cycle Time At Maximum Cas Latancy Minus 1 (2nd highest CL) */ + shift = (dimmInfo->memoryType == DDR) ? 4 : 2; + mult = (dimmInfo->memoryType == DDR) ? 10 : 25; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf : 0x03; + leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; + rightOfPoint = (data[i] & maskRightOfPoint) * mult; + dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_LoP = + leftOfPoint; + dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_RoP = + rightOfPoint; + debug("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint); /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */ + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 24: /* Clock To Data Out 2nd highest Cas Latency Value */ + div = (dimmInfo->memoryType == DDR) ? 100 : 10; + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / div; + rightOfPoint = time_tmp % div; + dimmInfo->clockToDataOutMinus1_LoP = leftOfPoint; + dimmInfo->clockToDataOutMinus1_RoP = rightOfPoint; + debug + ("Clock To Data Out (2nd CL value): %d.%2d [ns]\n", + leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 25: /* Minimum Cycle Time At Maximum Cas Latancy Minus 2 (3rd highest CL) */ + shift = (dimmInfo->memoryType == DDR) ? 4 : 2; + mult = (dimmInfo->memoryType == DDR) ? 10 : 25; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0xf : 0x03; + leftOfPoint = (data[i] & maskLeftOfPoint) >> shift; + rightOfPoint = (data[i] & maskRightOfPoint) * mult; + dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_LoP = + leftOfPoint; + dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_RoP = + rightOfPoint; + debug("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint); /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */ + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 26: /* Clock To Data Out 3rd highest Cas Latency Value */ + div = (dimmInfo->memoryType == DDR) ? 100 : 10; + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / div; + rightOfPoint = time_tmp % div; + dimmInfo->clockToDataOutMinus2_LoP = leftOfPoint; + dimmInfo->clockToDataOutMinus2_RoP = rightOfPoint; + debug + ("Clock To Data Out (3rd CL value): %d.%2d [ns]\n", + leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 27: /* Minimum Row Precharge Time */ + shift = (dimmInfo->memoryType == DDR) ? 2 : 0; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; + leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); + rightOfPoint = (data[i] & maskRightOfPoint) * 25; + + dimmInfo->minRowPrechargeTime = ((leftOfPoint * 100) + rightOfPoint); /* measured in n times 10ps Intervals */ + trp_clocks = + (dimmInfo->minRowPrechargeTime + + (tmemclk - 1)) / tmemclk; + debug + ("*** 1 clock cycle = %ld 10ps intervalls = %ld.%ld ns****\n", + tmemclk, tmemclk / 100, tmemclk % 100); + debug + ("Minimum Row Precharge Time [ns]: %d.%2d = in Clk cycles %d\n", + leftOfPoint, rightOfPoint, trp_clocks); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 28: /* Minimum Row Active to Row Active Time */ + shift = (dimmInfo->memoryType == DDR) ? 2 : 0; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; + leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); + rightOfPoint = (data[i] & maskRightOfPoint) * 25; + + dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */ + debug + ("Minimum Row Active -To- Row Active Delay [ns]: %d.%2d = in Clk cycles %d\n", + leftOfPoint, rightOfPoint, trp_clocks); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 29: /* Minimum Ras-To-Cas Delay */ + shift = (dimmInfo->memoryType == DDR) ? 2 : 0; + maskLeftOfPoint = + (dimmInfo->memoryType == DDR) ? 0xfc : 0xff; + maskRightOfPoint = + (dimmInfo->memoryType == DDR) ? 0x03 : 0x00; + leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift); + rightOfPoint = (data[i] & maskRightOfPoint) * 25; + + dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */ + debug + ("Minimum Ras-To-Cas Delay [ns]: %d.%2d = in Clk cycles %d\n", + leftOfPoint, rightOfPoint, trp_clocks); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 30: /* Minimum Ras Pulse Width */ + dimmInfo->minRasPulseWidth = data[i]; + tras_clocks = + (NSto10PS (data[i]) + + (tmemclk - 1)) / tmemclk; + debug + ("Minimum Ras Pulse Width [ns]: %d = in Clk cycles %d\n", + dimmInfo->minRasPulseWidth, tras_clocks); + + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 31: /* Module Bank Density */ + dimmInfo->moduleBankDensity = data[i]; + debug + ("Module Bank Density: %d\n", + dimmInfo->moduleBankDensity); +#ifdef DEBUG + debug + ("*** Offered Densities (more than 1 = Multisize-Module): "); + { + if (dimmInfo->moduleBankDensity & 1) + debug("4MB, "); + if (dimmInfo->moduleBankDensity & 2) + debug("8MB, "); + if (dimmInfo->moduleBankDensity & 4) + debug("16MB, "); + if (dimmInfo->moduleBankDensity & 8) + debug("32MB, "); + if (dimmInfo->moduleBankDensity & 16) + debug("64MB, "); + if (dimmInfo->moduleBankDensity & 32) + debug("128MB, "); + if ((dimmInfo->moduleBankDensity & 64) + || (dimmInfo->moduleBankDensity & 128)) { + debug("ERROR, "); + hang (); + } + } + debug("\n"); +#endif + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 32: /* Address And Command Setup Time (measured in ns/1000) */ + sign = 1; + switch (dimmInfo->memoryType) { + case DDR: + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / 100; + rightOfPoint = time_tmp % 100; + break; + case SDRAM: + leftOfPoint = (data[i] & 0xf0) >> 4; + if (leftOfPoint > 7) { + leftOfPoint = data[i] & 0x70 >> 4; + sign = -1; + } + rightOfPoint = (data[i] & 0x0f); + break; + } + dimmInfo->addrAndCommandSetupTime = + (leftOfPoint * 100 + rightOfPoint) * sign; + debug + ("Address And Command Setup Time [ns]: %d.%d\n", + sign * leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 33: /* Address And Command Hold Time */ + sign = 1; + switch (dimmInfo->memoryType) { + case DDR: + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / 100; + rightOfPoint = time_tmp % 100; + break; + case SDRAM: + leftOfPoint = (data[i] & 0xf0) >> 4; + if (leftOfPoint > 7) { + leftOfPoint = data[i] & 0x70 >> 4; + sign = -1; + } + rightOfPoint = (data[i] & 0x0f); + break; + } + dimmInfo->addrAndCommandHoldTime = + (leftOfPoint * 100 + rightOfPoint) * sign; + debug + ("Address And Command Hold Time [ns]: %d.%d\n", + sign * leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 34: /* Data Input Setup Time */ + sign = 1; + switch (dimmInfo->memoryType) { + case DDR: + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / 100; + rightOfPoint = time_tmp % 100; + break; + case SDRAM: + leftOfPoint = (data[i] & 0xf0) >> 4; + if (leftOfPoint > 7) { + leftOfPoint = data[i] & 0x70 >> 4; + sign = -1; + } + rightOfPoint = (data[i] & 0x0f); + break; + } + dimmInfo->dataInputSetupTime = + (leftOfPoint * 100 + rightOfPoint) * sign; + debug + ("Data Input Setup Time [ns]: %d.%d\n", + sign * leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + + case 35: /* Data Input Hold Time */ + sign = 1; + switch (dimmInfo->memoryType) { + case DDR: + time_tmp = + (((data[i] & 0xf0) >> 4) * 10) + + ((data[i] & 0x0f)); + leftOfPoint = time_tmp / 100; + rightOfPoint = time_tmp % 100; + break; + case SDRAM: + leftOfPoint = (data[i] & 0xf0) >> 4; + if (leftOfPoint > 7) { + leftOfPoint = data[i] & 0x70 >> 4; + sign = -1; + } + rightOfPoint = (data[i] & 0x0f); + break; + } + dimmInfo->dataInputHoldTime = + (leftOfPoint * 100 + rightOfPoint) * sign; + debug + ("Data Input Hold Time [ns]: %d.%d\n\n", + sign * leftOfPoint, rightOfPoint); + break; +/*------------------------------------------------------------------------------------------------------------------------------*/ + } + } + /* calculating the sdram density */ + for (i = 0; + i < dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses; + i++) { + density = density * 2; + } + dimmInfo->deviceDensity = density * dimmInfo->numOfBanksOnEachDevice * + dimmInfo->sdramWidth; + dimmInfo->numberOfDevices = + (dimmInfo->dataWidth / dimmInfo->sdramWidth) * + dimmInfo->numOfModuleBanks; + if ((dimmInfo->errorCheckType == 0x1) + || (dimmInfo->errorCheckType == 0x2) + || (dimmInfo->errorCheckType == 0x3)) { + dimmInfo->size = + (dimmInfo->deviceDensity / 8) * + (dimmInfo->numberOfDevices - + /* ronen on the 1G dimm we get wrong value. (was devicesForErrCheck) */ + dimmInfo->numberOfDevices / 8); + } else { + dimmInfo->size = + (dimmInfo->deviceDensity / 8) * + dimmInfo->numberOfDevices; + } + + /* compute the module DRB size */ + tmp = (1 << + (dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses)); + tmp *= dimmInfo->numOfModuleBanks; + tmp *= dimmInfo->sdramWidth; + tmp = tmp >> 24; /* div by 0x4000000 (64M) */ + dimmInfo->drb_size = (uchar) tmp; + debug("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size); + + /* try a CAS latency of 3 first... */ + + /* bit 1 is CL2, bit 2 is CL3 */ + supp_cal = (dimmInfo->suportedCasLatencies & 0x6) >> 1; + + cal_val = 0; + if (supp_cal & 3) { + if (NS10to10PS (data[9]) <= tmemclk) + cal_val = 3; + } + + /* then 2... */ + if (supp_cal & 2) { + if (NS10to10PS (data[23]) <= tmemclk) + cal_val = 2; + } + + debug("cal_val = %d\n", cal_val); + + /* bummer, did't work... */ + if (cal_val == 0) { + debug("Couldn't find a good CAS latency\n"); + hang (); + return 0; + } + + return true; +#endif +} + +/* sets up the GT properly with information passed in */ +int setup_sdram (AUX_MEM_DIMM_INFO * info) +{ + ulong tmp, check; + ulong tmp_sdram_mode = 0; /* 0x141c */ + ulong tmp_dunit_control_low = 0; /* 0x1404 */ + int i; + + /* added 8/21/2003 P. Marchese */ + unsigned int sdram_config_reg; + + /* added 10/10/2003 P. Marchese */ + ulong sdram_chip_size; + + /* sanity checking */ + if (!info->numOfModuleBanks) { + printf ("setup_sdram called with 0 banks\n"); + return 1; + } + + /* delay line */ + set_dfcdlInit (); /* may be its not needed */ + debug("Delay line set done\n"); + + /* set SDRAM mode NOP */ /* To_do check it */ + GT_REG_WRITE (SDRAM_OPERATION, 0x5); + while (GTREGREAD (SDRAM_OPERATION) != 0) { + debug + ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n"); + } + + /* SDRAM configuration */ +/* added 8/21/2003 P. Marchese */ +/* code allows usage of registered DIMMS */ + + /* figure out the memory refresh internal */ + switch (info->RefreshInterval) { + case 0x0: + case 0x80: /* refresh period is 15.625 usec */ + sdram_config_reg = + (unsigned int) (((float) 15.625 * (float) CONFIG_SYS_BUS_CLK) + / (float) 1000000.0); + break; + case 0x1: + case 0x81: /* refresh period is 3.9 usec */ + sdram_config_reg = + (unsigned int) (((float) 3.9 * (float) CONFIG_SYS_BUS_CLK) / + (float) 1000000.0); + break; + case 0x2: + case 0x82: /* refresh period is 7.8 usec */ + sdram_config_reg = + (unsigned int) (((float) 7.8 * (float) CONFIG_SYS_BUS_CLK) / + (float) 1000000.0); + break; + case 0x3: + case 0x83: /* refresh period is 31.3 usec */ + sdram_config_reg = + (unsigned int) (((float) 31.3 * (float) CONFIG_SYS_BUS_CLK) / + (float) 1000000.0); + break; + case 0x4: + case 0x84: /* refresh period is 62.5 usec */ + sdram_config_reg = + (unsigned int) (((float) 62.5 * (float) CONFIG_SYS_BUS_CLK) / + (float) 1000000.0); + break; + case 0x5: + case 0x85: /* refresh period is 125 usec */ + sdram_config_reg = + (unsigned int) (((float) 125 * (float) CONFIG_SYS_BUS_CLK) / + (float) 1000000.0); + break; + default: /* refresh period undefined */ + printf ("DRAM refresh period is unknown!\n"); + printf ("Aborting DRAM setup with an error\n"); + hang (); + break; + } + debug("calculated refresh interval %0x\n", sdram_config_reg); + + /* make sure the refresh value is only 14 bits */ + if (sdram_config_reg > 0x1fff) + sdram_config_reg = 0x1fff; + debug("adjusted refresh interval %0x\n", sdram_config_reg); + + /* we want physical bank interleaving and */ + /* virtual bank interleaving enabled so do nothing */ + /* since these bits need to be zero to enable the interleaving */ + + /* registered DRAM ? */ + if (info->registeredAddrAndControlInputs == 1) { + /* it's registered DRAM, so set the reg. DRAM bit */ + sdram_config_reg = sdram_config_reg | BIT17; + debug("Enabling registered DRAM bit\n"); + } + /* turn on DRAM ECC? */ +#ifdef CONFIG_MV64460_ECC + if (info->errorCheckType == 0x2) { + /* DRAM has ECC, so turn it on */ + sdram_config_reg = sdram_config_reg | BIT18; + debug("Enabling ECC\n"); + } +#endif + /* set the data DQS pin configuration */ + switch (info->sdramWidth) { + case 0x4: /* memory is x4 */ + sdram_config_reg = sdram_config_reg | BIT20 | BIT21; + debug("Data DQS pins set for 16 pins\n"); + break; + case 0x8: /* memory is x8 or x16 */ + case 0x10: + sdram_config_reg = sdram_config_reg | BIT21; + debug("Data DQS pins set for 8 pins\n"); + break; + case 0x20: /* memory is x32 */ + /* both bits are cleared for x32 so nothing to do */ + debug("Data DQS pins set for 2 pins\n"); + break; + default: /* memory width unsupported */ + printf ("DRAM chip width is unknown!\n"); + printf ("Aborting DRAM setup with an error\n"); + hang (); + break; + } + + /*ronen db64460 */ + /* perform read buffer assignments */ + /* we are going to use the Power-up defaults */ + /* bit 27 = PCI bus #0 = buffer 0 */ + /* bit 28 = PCI bus #1 = buffer 0 */ + /* bit 29 = MPSC = buffer 0 */ + /* bit 30 = IDMA = buffer 0 */ + /* bit 31 = Gigabit = buffer 0 */ + sdram_config_reg = sdram_config_reg | 0x58000000; + sdram_config_reg = sdram_config_reg & 0xffffff00; + /* bit 14 FBSplit = FCRAM controller bsplit enable. */ + /* bit 15 vw = FCRAM Variable write length enable. */ + /* bit 16 DType = Dram Type (0 = FCRAM,1 = Standard) */ + sdram_config_reg = sdram_config_reg | BIT14 | BIT15; + + /* write the value into the SDRAM configuration register */ + GT_REG_WRITE (SDRAM_CONFIG, sdram_config_reg); + debug("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG)); + + /* SDRAM open pages control keep open as much as I can */ + GT_REG_WRITE (SDRAM_OPEN_PAGES_CONTROL, 0x0); + debug + ("sdram_open_pages_controll 0x1414: %08x\n", + GTREGREAD (SDRAM_OPEN_PAGES_CONTROL)); + + /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */ + tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01); /* Clock Domain Sync from power on reset */ + if (tmp == 0) + debug("Core Signals are sync (by HW-Setting)!!!\n"); + else + debug + ("Core Signals syncs. are bypassed (by HW-Setting)!!!\n"); + + /* SDRAM set CAS Latency according to SPD information */ + switch (info->memoryType) { + case SDRAM: + printf ("### SD-RAM not supported !!!\n"); + printf ("Aborting!!!\n"); + hang (); + /* ToDo fill SD-RAM if needed !!!!! */ + break; + /* Calculate the settings for SDRAM mode and Dunit control low registers */ + /* Values set according to technical bulletin TB-92 rev. c */ + case DDR: + debug("### SET-CL for DDR-RAM\n"); + /* ronen db64460 - change the tmp_dunit_control_low setting!!! */ + switch (info->maxClSupported_DDR) { + case DDR_CL_3: + tmp_sdram_mode = 0x32; /* CL=3 Burstlength = 4 */ + if (tmp == 1) { /* clocks sync */ + if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0x05110051; + else + tmp_dunit_control_low = 0x24110051; + debug + ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n"); + } else { /* clk sync. bypassed */ + + if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0xC5000540; + else + tmp_dunit_control_low = 0xC4000540; + debug + ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + } + break; + case DDR_CL_2_5: + tmp_sdram_mode = 0x62; /* CL=2.5 Burstlength = 4 */ + if (tmp == 1) { /* clocks sync */ + if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0x25110051; + else + tmp_dunit_control_low = 0x24110051; + debug + ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n"); + } else { /* clk sync. bypassed */ + + if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0xC5000540; + /* printf("CL = 2.5, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */ + /* printf("Aborting!!!\n");1 */ + /* hang();1 */ + } else + tmp_dunit_control_low = 0xC4000540; + debug + ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + } + break; + case DDR_CL_2: + tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */ + if (tmp == 1) { /* clocks sync */ + if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0x04110051; + else + tmp_dunit_control_low = 0x03110051; + debug + ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n"); + } else { /* clk sync. bypassed */ + + if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */ + /*printf("CL = 2, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */ + /*printf("Aborting!!!\n");1 */ + /*hang();1 */ + tmp_dunit_control_low = 0xC4000540; + } else + tmp_dunit_control_low = 0xC3000540;; + debug + ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + } + break; + case DDR_CL_1_5: + tmp_sdram_mode = 0x52; /* CL=1.5 Burstlength = 4 */ + if (tmp == 1) { /* clocks sync */ + if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */ + tmp_dunit_control_low = 0x24110051; + else + tmp_dunit_control_low = 0x23110051; + debug + ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n"); + } else { /* clk sync. bypassed */ + + if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */ + /*printf("CL = 1.5, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */ + /*printf("Aborting!!!\n");1 */ + /*hang();1 */ + tmp_dunit_control_low = 0xC4000540; + } else + tmp_dunit_control_low = 0xC3000540; + debug + ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n", + tmp_sdram_mode, tmp_dunit_control_low); + } + break; + + default: + printf ("Max. CL is out of range %d\n", + info->maxClSupported_DDR); + hang (); + break; + } /* end DDR switch */ + break; + } /* end CL switch */ + + /* Write results of CL detection procedure */ + /* set SDRAM mode reg. 0x141c */ + GT_REG_WRITE (SDRAM_MODE, tmp_sdram_mode); + + /* set SDRAM mode SetCommand 0x1418 */ + GT_REG_WRITE (SDRAM_OPERATION, 0x3); + while (GTREGREAD (SDRAM_OPERATION) != 0) { + debug + ("\n*** SDRAM_OPERATION 0x1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"); + } + + /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */ + GT_REG_WRITE (D_UNIT_CONTROL_LOW, tmp_dunit_control_low); + + /* set SDRAM mode SetCommand 0x1418 */ + GT_REG_WRITE (SDRAM_OPERATION, 0x3); + while (GTREGREAD (SDRAM_OPERATION) != 0) { + debug + ("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n"); + } + +/*------------------------------------------------------------------------------ */ + + /* bank parameters */ + /* SDRAM address decode register 0x1410 */ + /* program this with the default value */ + tmp = 0x02; /* power-up default address select decoding value */ + + debug("drb_size (n*64Mbit): %d\n", info->drb_size); +/* figure out the DRAM chip size */ + sdram_chip_size = + (1 << (info->numOfRowAddresses + info->numOfColAddresses)); + sdram_chip_size *= info->sdramWidth; + sdram_chip_size *= 4; + debug("computed sdram chip size is %#lx\n", sdram_chip_size); + /* divide sdram chip size by 64 Mbits */ + sdram_chip_size = sdram_chip_size / 0x4000000; + switch (sdram_chip_size) { + case 1: /* 64 Mbit */ + case 2: /* 128 Mbit */ + debug("RAM-Device_size 64Mbit or 128Mbit)\n"); + tmp |= (0x00 << 4); + break; + case 4: /* 256 Mbit */ + case 8: /* 512 Mbit */ + debug("RAM-Device_size 256Mbit or 512Mbit)\n"); + tmp |= (0x01 << 4); + break; + case 16: /* 1 Gbit */ + case 32: /* 2 Gbit */ + debug("RAM-Device_size 1Gbit or 2Gbit)\n"); + tmp |= (0x02 << 4); + break; + default: + printf ("Error in dram size calculation\n"); + printf ("RAM-Device_size is unsupported\n"); + hang (); + } + + /* SDRAM address control */ + GT_REG_WRITE (SDRAM_ADDR_CONTROL, tmp); + debug + ("setting up sdram address control (0x1410) with: %08lx \n", + tmp); + +/* ------------------------------------------------------------------------------ */ +/* same settings for registerd & non-registerd DDR SDRAM */ + debug + ("setting up sdram_timing_control_low (0x1408) with: %08x \n", + 0x01501220); + /*ronen db64460 */ + GT_REG_WRITE (SDRAM_TIMING_CONTROL_LOW, 0x01501220); + + +/* ------------------------------------------------------------------------------ */ + + /* SDRAM configuration */ + tmp = GTREGREAD (SDRAM_CONFIG); + + if (info->registeredAddrAndControlInputs + || info->registeredDQMBinputs) { + tmp |= (1 << 17); + debug + ("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n", + info->registeredAddrAndControlInputs, + info->registeredDQMBinputs); + } + + /* Use buffer 1 to return read data to the CPU + * Page 426 MV6indent: Standard input:1464: Warning:old style assignment ambiguity in "=*". Assuming "= *" + +indent: Standard input:1465: Warning:old style assignment ambiguity in "=*". Assuming "= *" + +4460 */ + tmp |= (1 << 26); + debug + ("Before Buffer assignment - sdram_conf (0x1400): %08x\n", + GTREGREAD (SDRAM_CONFIG)); + debug + ("After Buffer assignment - sdram_conf (0x1400): %08x\n", + GTREGREAD (SDRAM_CONFIG)); + + /* SDRAM timing To_do: */ +/* ------------------------------------------------------------------------------ */ + /* ronen db64460 */ + debug + ("setting up sdram_timing_control_high (0x140c) with: %08x \n", + 0xc); + GT_REG_WRITE (SDRAM_TIMING_CONTROL_HIGH, 0xc); + + debug + ("setting up sdram address pads control (0x14c0) with: %08x \n", + 0x7d5014a); + GT_REG_WRITE (SDRAM_ADDR_CTRL_PADS_CALIBRATION, 0x7d5014a); + + debug + ("setting up sdram data pads control (0x14c4) with: %08x \n", + 0x7d5014a); + GT_REG_WRITE (SDRAM_DATA_PADS_CALIBRATION, 0x7d5014a); + +/* ------------------------------------------------------------------------------ */ + + /* set the SDRAM configuration for each bank */ + +/* for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */ + { + i = info->slot; + debug + ("\n*** Running a MRS cycle for bank %d ***\n", i); + + /* map the bank */ + memory_map_bank (i, 0, GB / 4); + + /* set SDRAM mode */ /* To_do check it */ + GT_REG_WRITE (SDRAM_OPERATION, 0x3); + check = GTREGREAD (SDRAM_OPERATION); + debug + ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n", + check); + + + /* switch back to normal operation mode */ + GT_REG_WRITE (SDRAM_OPERATION, 0); + check = GTREGREAD (SDRAM_OPERATION); + debug + ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n", + check); + + /* unmap the bank */ + memory_map_bank (i, 0, 0); + } + + return 0; + +} + +/* + * Check memory range for valid RAM. A simple memory test determines + * the actually available RAM size between addresses `base' and + * `base + maxsize'. Some (not all) hardware errors are detected: + * - short between address lines + * - short between data lines + */ +long int dram_size (long int *base, long int maxsize) +{ + volatile long int *addr, *b = base; + long int cnt, val, save1, save2; + +#define STARTVAL (1<<20) /* start test at 1M */ + for (cnt = STARTVAL / sizeof (long); cnt < maxsize / sizeof (long); + cnt <<= 1) { + addr = base + cnt; /* pointer arith! */ + + save1 = *addr; /* save contents of addr */ + save2 = *b; /* save contents of base */ + + *addr = cnt; /* write cnt to addr */ + *b = 0; /* put null at base */ + + /* check at base address */ + if ((*b) != 0) { + *addr = save1; /* restore *addr */ + *b = save2; /* restore *b */ + return (0); + } + val = *addr; /* read *addr */ + val = *addr; /* read *addr */ + + *addr = save1; + *b = save2; + + if (val != cnt) { + debug + ("Found %08x at Address %08x (failure)\n", + (unsigned int) val, (unsigned int) addr); + /* fix boundary condition.. STARTVAL means zero */ + if (cnt == STARTVAL / sizeof (long)) + cnt = 0; + return (cnt * sizeof (long)); + } + } + return maxsize; +} + +/* ------------------------------------------------------------------------- */ + +/* ppcboot interface function to SDRAM init - this is where all the + * controlling logic happens */ +phys_size_t initdram (int board_type) +{ + int checkbank[4] = {[0 ... 3] = 0 }; + ulong realsize, total; + AUX_MEM_DIMM_INFO dimmInfo1; + AUX_MEM_DIMM_INFO dimmInfo2; + int nhr, bank_no; + ulong dest, memSpaceAttr; + + /* first, use the SPD to get info about the SDRAM/ DDRRAM */ + + /* check the NHR bit and skip mem init if it's already done */ + nhr = get_hid0 () & (1 << 16); + + if (nhr) { + printf ("Skipping SD- DDRRAM setup due to NHR bit being set\n"); + } else { + /* DIMM0 */ + check_dimm (0, &dimmInfo1); + + /* DIMM1 */ + check_dimm (1, &dimmInfo2); + + memory_map_bank (0, 0, 0); + memory_map_bank (1, 0, 0); + memory_map_bank (2, 0, 0); + memory_map_bank (3, 0, 0); + + /* ronen check correct set of DIMMS */ + if (dimmInfo1.numOfModuleBanks && dimmInfo2.numOfModuleBanks) { + if (dimmInfo1.errorCheckType != + dimmInfo2.errorCheckType) + printf ("***WARNNING***!!!! different ECC support of the DIMMS\n"); + if (dimmInfo1.maxClSupported_DDR != + dimmInfo2.maxClSupported_DDR) + printf ("***WARNNING***!!!! different CAL setting of the DIMMS\n"); + if (dimmInfo1.registeredAddrAndControlInputs != + dimmInfo2.registeredAddrAndControlInputs) + printf ("***WARNNING***!!!! different Registration setting of the DIMMS\n"); + } + + if (dimmInfo1.numOfModuleBanks && setup_sdram (&dimmInfo1)) { + printf ("Setup for DIMM1 failed.\n"); + } + + if (dimmInfo2.numOfModuleBanks && setup_sdram (&dimmInfo2)) { + printf ("Setup for DIMM2 failed.\n"); + } + + /* set the NHR bit */ + set_hid0 (get_hid0 () | (1 << 16)); + } + /* next, size the SDRAM banks */ + + realsize = total = 0; + if (dimmInfo1.numOfModuleBanks > 0) { + checkbank[0] = 1; + } + if (dimmInfo1.numOfModuleBanks > 1) { + checkbank[1] = 1; + } + if (dimmInfo1.numOfModuleBanks > 2) + printf ("Error, SPD claims DIMM1 has >2 banks\n"); + + printf ("-- DIMM1 has %d banks\n", dimmInfo1.numOfModuleBanks); + + if (dimmInfo2.numOfModuleBanks > 0) { + checkbank[2] = 1; + } + if (dimmInfo2.numOfModuleBanks > 1) { + checkbank[3] = 1; + } + if (dimmInfo2.numOfModuleBanks > 2) + printf ("Error, SPD claims DIMM2 has >2 banks\n"); + + printf ("-- DIMM2 has %d banks\n", dimmInfo2.numOfModuleBanks); + + for (bank_no = 0; bank_no < CONFIG_SYS_DRAM_BANKS; bank_no++) { + /* skip over banks that are not populated */ + if (!checkbank[bank_no]) + continue; + + /* ronen - realsize = dram_size((long int *)total, check); */ + if (bank_no == 0 || bank_no == 1) { + if (checkbank[1] == 1) + realsize = dimmInfo1.size / 2; + else + realsize = dimmInfo1.size; + } + if (bank_no == 2 || bank_no == 3) { + if (checkbank[3] == 1) + realsize = dimmInfo2.size / 2; + else + realsize = dimmInfo2.size; + } + memory_map_bank (bank_no, total, realsize); + + /* ronen - initialize the DRAM for ECC */ +#ifdef CONFIG_MV64460_ECC + if ((dimmInfo1.errorCheckType != 0) && + ((dimmInfo2.errorCheckType != 0) + || (dimmInfo2.numOfModuleBanks == 0))) { + printf ("ECC Initialization of Bank %d:", bank_no); + memSpaceAttr = ((~(BIT0 << bank_no)) & 0xf) << 8; + mvDmaSetMemorySpace (0, 0, memSpaceAttr, total, + realsize); + for (dest = total; dest < total + realsize; + dest += _8M) { + mvDmaTransfer (0, total, dest, _8M, + BIT8 /*DMA_DTL_128BYTES */ | + BIT3 /*DMA_HOLD_SOURCE_ADDR */ + | + BIT11 + /*DMA_BLOCK_TRANSFER_MODE */ ); + while (mvDmaIsChannelActive (0)); + } + printf (" PASS\n"); + } +#endif + + total += realsize; + } + + /* ronen */ + switch ((GTREGREAD (0x141c) >> 4) & 0x7) { + case 0x2: + printf ("CAS Latency = 2"); + break; + case 0x3: + printf ("CAS Latency = 3"); + break; + case 0x5: + printf ("CAS Latency = 1.5"); + break; + case 0x6: + printf ("CAS Latency = 2.5"); + break; + } + printf (" tRP = %d tRAS = %d tRCD=%d\n", + ((GTREGREAD (0x1408) >> 8) & 0xf) + 1, + ((GTREGREAD (0x1408) >> 20) & 0xf) + 1, + ((GTREGREAD (0x1408) >> 4) & 0xf) + 1); + +/* Setup Ethernet DMA Adress window to DRAM Area */ + if (total > _256M) + printf ("*** ONLY the first 256MB DRAM memory are used out of the "); + else + printf ("Total SDRAM memory is "); + /* (cause all the 4 BATS are taken) */ + return (total); +} + + +/* ronen- add Idma functions for usage of the ecc dram init. */ +/******************************************************************************* +* mvDmaIsChannelActive - Checks if a engine is busy. +********************************************************************************/ +int mvDmaIsChannelActive (int engine) +{ + ulong data; + + data = GTREGREAD (MV64460_DMA_CHANNEL0_CONTROL + 4 * engine); + if (data & BIT14 /*activity status */ ) { + return 1; + } + return 0; +} + +/******************************************************************************* +* mvDmaSetMemorySpace - Set a DMA memory window for the DMA's address decoding +* map. +*******************************************************************************/ +int mvDmaSetMemorySpace (ulong memSpace, + ulong memSpaceTarget, + ulong memSpaceAttr, ulong baseAddress, ulong size) +{ + ulong temp; + + /* The base address must be aligned to the size. */ + if (baseAddress % size != 0) { + return 0; + } + if (size >= 0x10000 /*64K */ ) { + size &= 0xffff0000; + baseAddress = (baseAddress & 0xffff0000); + /* Set the new attributes */ + GT_REG_WRITE (MV64460_DMA_BASE_ADDR_REG0 + memSpace * 8, + (baseAddress | memSpaceTarget | memSpaceAttr)); + GT_REG_WRITE ((MV64460_DMA_SIZE_REG0 + memSpace * 8), + (size - 1) & 0xffff0000); + temp = GTREGREAD (MV64460_DMA_BASE_ADDR_ENABLE_REG); + GT_REG_WRITE (DMA_BASE_ADDR_ENABLE_REG, + (temp & ~(BIT0 << memSpace))); + return 1; + } + return 0; +} + + +/******************************************************************************* +* mvDmaTransfer - Transfer data from sourceAddr to destAddr on one of the 4 +* DMA channels. +********************************************************************************/ +int mvDmaTransfer (int engine, ulong sourceAddr, + ulong destAddr, ulong numOfBytes, ulong command) +{ + ulong engOffReg = 0; /* Engine Offset Register */ + + if (numOfBytes > 0xffff) { + command = command | BIT31 /*DMA_16M_DESCRIPTOR_MODE */ ; + } + command = command | ((command >> 6) & 0x7); + engOffReg = engine * 4; + GT_REG_WRITE (MV64460_DMA_CHANNEL0_BYTE_COUNT + engOffReg, + numOfBytes); + GT_REG_WRITE (MV64460_DMA_CHANNEL0_SOURCE_ADDR + engOffReg, + sourceAddr); + GT_REG_WRITE (MV64460_DMA_CHANNEL0_DESTINATION_ADDR + engOffReg, + destAddr); + command = + command | BIT12 /*DMA_CHANNEL_ENABLE */ | BIT9 + /*DMA_NON_CHAIN_MODE */ ; + /* Activate DMA engine By writting to mvDmaControlRegister */ + GT_REG_WRITE (MV64460_DMA_CHANNEL0_CONTROL + engOffReg, command); + return 1; +} + +/**************************************************************************************** + * SDRAM INIT * + * This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb * + * This procedure fits only the Atlantis * + * * + ***************************************************************************************/ + + +/**************************************************************************************** + * DFCDL initialize MV643xx Design Considerations * + * * + ***************************************************************************************/ +int set_dfcdlInit (void) +{ + /*ronen the dfcdl init are done by the I2C */ + return (0); +}