X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=kernel%2Fdrivers%2Fstaging%2Frtl8192u%2Fieee80211%2Frtl819x_HT.h;fp=kernel%2Fdrivers%2Fstaging%2Frtl8192u%2Fieee80211%2Frtl819x_HT.h;h=c3aabbaac7ae200b7599a369312a7217a206c539;hb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;hp=0000000000000000000000000000000000000000;hpb=98260f3884f4a202f9ca5eabed40b1354c489b29;p=kvmfornfv.git diff --git a/kernel/drivers/staging/rtl8192u/ieee80211/rtl819x_HT.h b/kernel/drivers/staging/rtl8192u/ieee80211/rtl819x_HT.h new file mode 100644 index 000000000..c3aabbaac --- /dev/null +++ b/kernel/drivers/staging/rtl8192u/ieee80211/rtl819x_HT.h @@ -0,0 +1,480 @@ +#ifndef _RTL819XU_HTTYPE_H_ +#define _RTL819XU_HTTYPE_H_ + +//------------------------------------------------------------ +// The HT Capability element is present in beacons, association request, +// reassociation request and probe response frames +//------------------------------------------------------------ + +// +// Operation mode value +// +#define HT_OPMODE_NO_PROTECT 0 +#define HT_OPMODE_OPTIONAL 1 +#define HT_OPMODE_40MHZ_PROTECT 2 +#define HT_OPMODE_MIXED 3 + +// +// MIMO Power Save Settings +// +#define MIMO_PS_STATIC 0 +#define MIMO_PS_DYNAMIC 1 +#define MIMO_PS_NOLIMIT 3 + + +// +// There should be 128 bits to cover all of the MCS rates. However, since +// 8190 does not support too much rates, one integer is quite enough. +// + +#define sHTCLng 4 + + +#define HT_SUPPORTED_MCS_1SS_BITMAP 0x000000ff +#define HT_SUPPORTED_MCS_2SS_BITMAP 0x0000ff00 +#define HT_SUPPORTED_MCS_1SS_2SS_BITMAP HT_MCS_1SS_BITMAP|HT_MCS_1SS_2SS_BITMAP + + +typedef enum _HT_MCS_RATE{ + HT_MCS0 = 0x00000001, + HT_MCS1 = 0x00000002, + HT_MCS2 = 0x00000004, + HT_MCS3 = 0x00000008, + HT_MCS4 = 0x00000010, + HT_MCS5 = 0x00000020, + HT_MCS6 = 0x00000040, + HT_MCS7 = 0x00000080, + HT_MCS8 = 0x00000100, + HT_MCS9 = 0x00000200, + HT_MCS10 = 0x00000400, + HT_MCS11 = 0x00000800, + HT_MCS12 = 0x00001000, + HT_MCS13 = 0x00002000, + HT_MCS14 = 0x00004000, + HT_MCS15 = 0x00008000, + // Do not define MCS32 here although 8190 support MCS32 +} HT_MCS_RATE, *PHT_MCS_RATE; + +// +// Represent Channel Width in HT Capabilities +// +typedef enum _HT_CHANNEL_WIDTH{ + HT_CHANNEL_WIDTH_20 = 0, + HT_CHANNEL_WIDTH_20_40 = 1, +}HT_CHANNEL_WIDTH, *PHT_CHANNEL_WIDTH; + +// +// Represent Extension Channel Offset in HT Capabilities +// This is available only in 40Mhz mode. +// +typedef enum _HT_EXTCHNL_OFFSET{ + HT_EXTCHNL_OFFSET_NO_EXT = 0, + HT_EXTCHNL_OFFSET_UPPER = 1, + HT_EXTCHNL_OFFSET_NO_DEF = 2, + HT_EXTCHNL_OFFSET_LOWER = 3, +}HT_EXTCHNL_OFFSET, *PHT_EXTCHNL_OFFSET; + +typedef enum _CHNLOP{ + CHNLOP_NONE = 0, // No Action now + CHNLOP_SCAN = 1, // Scan in progress + CHNLOP_SWBW = 2, // Bandwidth switching in progress + CHNLOP_SWCHNL = 3, // Software Channel switching in progress +} CHNLOP, *PCHNLOP; + +// Determine if the Channel Operation is in progress +#define CHHLOP_IN_PROGRESS(_pHTInfo) \ + ((_pHTInfo)->ChnlOp > CHNLOP_NONE) ? TRUE : FALSE + +/* +typedef union _HT_CAPABILITY{ + u16 ShortData; + u8 CharData[2]; + struct + { + u16 AdvCoding:1; + u16 ChlWidth:1; + u16 MimoPwrSave:2; + u16 GreenField:1; + u16 ShortGI20Mhz:1; + u16 ShortGI40Mhz:1; + u16 STBC:1; + u16 BeamForm:1; + u16 DelayBA:1; + u16 MaxAMSDUSize:1; + u16 DssCCk:1; + u16 PSMP:1; + u16 Rsvd:3; + }Field; +}HT_CAPABILITY, *PHT_CAPABILITY; + +typedef union _HT_CAPABILITY_MACPARA{ + u8 ShortData; + u8 CharData[1]; + struct + { + u8 MaxRxAMPDU:2; + u8 MPDUDensity:2; + u8 Rsvd:4; + }Field; +}HT_CAPABILITY_MACPARA, *PHT_CAPABILITY_MACPARA; +*/ + +typedef enum _HT_ACTION{ + ACT_RECOMMAND_WIDTH = 0, + ACT_MIMO_PWR_SAVE = 1, + ACT_PSMP = 2, + ACT_SET_PCO_PHASE = 3, + ACT_MIMO_CHL_MEASURE = 4, + ACT_RECIPROCITY_CORRECT = 5, + ACT_MIMO_CSI_MATRICS = 6, + ACT_MIMO_NOCOMPR_STEER = 7, + ACT_MIMO_COMPR_STEER = 8, + ACT_ANTENNA_SELECT = 9, +} HT_ACTION, *PHT_ACTION; + + +/* 2007/06/07 MH Define sub-carrier mode for 40MHZ. */ +typedef enum _HT_Bandwidth_40MHZ_Sub_Carrier{ + SC_MODE_DUPLICATE = 0, + SC_MODE_LOWER = 1, + SC_MODE_UPPER = 2, + SC_MODE_FULL40MHZ = 3, +}HT_BW40_SC_E; + +typedef struct _HT_CAPABILITY_ELE{ + + //HT capability info + u8 AdvCoding:1; + u8 ChlWidth:1; + u8 MimoPwrSave:2; + u8 GreenField:1; + u8 ShortGI20Mhz:1; + u8 ShortGI40Mhz:1; + u8 TxSTBC:1; + u8 RxSTBC:2; + u8 DelayBA:1; + u8 MaxAMSDUSize:1; + u8 DssCCk:1; + u8 PSMP:1; + u8 Rsvd1:1; + u8 LSigTxopProtect:1; + + //MAC HT parameters info + u8 MaxRxAMPDUFactor:2; + u8 MPDUDensity:3; + u8 Rsvd2:3; + + //Supported MCS set + u8 MCS[16]; + + + //Extended HT Capability Info + u16 ExtHTCapInfo; + + //TXBF Capabilities + u8 TxBFCap[4]; + + //Antenna Selection Capabilities + u8 ASCap; + +} __attribute__ ((packed)) HT_CAPABILITY_ELE, *PHT_CAPABILITY_ELE; + +//------------------------------------------------------------ +// The HT Information element is present in beacons +// Only AP is required to include this element +//------------------------------------------------------------ + +typedef struct _HT_INFORMATION_ELE{ + u8 ControlChl; + + u8 ExtChlOffset:2; + u8 RecommemdedTxWidth:1; + u8 RIFS:1; + u8 PSMPAccessOnly:1; + u8 SrvIntGranularity:3; + + u8 OptMode:2; + u8 NonGFDevPresent:1; + u8 Revd1:5; + u8 Revd2:8; + + u8 Rsvd3:6; + u8 DualBeacon:1; + u8 DualCTSProtect:1; + + u8 SecondaryBeacon:1; + u8 LSigTxopProtectFull:1; + u8 PcoActive:1; + u8 PcoPhase:1; + u8 Rsvd4:4; + + u8 BasicMSC[16]; +} __attribute__ ((packed)) HT_INFORMATION_ELE, *PHT_INFORMATION_ELE; + +// +// MIMO Power Save control field. +// This is appear in MIMO Power Save Action Frame +// +typedef struct _MIMOPS_CTRL{ + u8 MimoPsEnable:1; + u8 MimoPsMode:1; + u8 Reserved:6; +} MIMOPS_CTRL, *PMIMOPS_CTRL; + +typedef enum _HT_SPEC_VER{ + HT_SPEC_VER_IEEE = 0, + HT_SPEC_VER_EWC = 1, +}HT_SPEC_VER, *PHT_SPEC_VER; + +typedef enum _HT_AGGRE_MODE_E{ + HT_AGG_AUTO = 0, + HT_AGG_FORCE_ENABLE = 1, + HT_AGG_FORCE_DISABLE = 2, +}HT_AGGRE_MODE_E, *PHT_AGGRE_MODE_E; + +//------------------------------------------------------------ +// The Data structure is used to keep HT related variables when card is +// configured as non-AP STA mode. **Note** Current_xxx should be set +// to default value in HTInitializeHTInfo() +//------------------------------------------------------------ + +typedef struct _RT_HIGH_THROUGHPUT{ + u8 bEnableHT; + u8 bCurrentHTSupport; + + u8 bRegBW40MHz; // Tx 40MHz channel capability + u8 bCurBW40MHz; // Tx 40MHz channel capability + + u8 bRegShortGI40MHz; // Tx Short GI for 40Mhz + u8 bCurShortGI40MHz; // Tx Short GI for 40MHz + + u8 bRegShortGI20MHz; // Tx Short GI for 20MHz + u8 bCurShortGI20MHz; // Tx Short GI for 20MHz + + u8 bRegSuppCCK; // Tx CCK rate capability + u8 bCurSuppCCK; // Tx CCK rate capability + + // 802.11n spec version for "peer" + HT_SPEC_VER ePeerHTSpecVer; + + + // HT related information for "Self" + HT_CAPABILITY_ELE SelfHTCap; // This is HT cap element sent to peer STA, which also indicate HT Rx capabilities. + HT_INFORMATION_ELE SelfHTInfo; // This is HT info element sent to peer STA, which also indicate HT Rx capabilities. + + // HT related information for "Peer" + u8 PeerHTCapBuf[32]; + u8 PeerHTInfoBuf[32]; + + + // A-MSDU related + u8 bAMSDU_Support; // This indicates Tx A-MSDU capability + u16 nAMSDU_MaxSize; // This indicates Tx A-MSDU capability + u8 bCurrent_AMSDU_Support; // This indicates Tx A-MSDU capability + u16 nCurrent_AMSDU_MaxSize; // This indicates Tx A-MSDU capability + + + // AMPDU related <2006.08.10 Emily> + u8 bAMPDUEnable; // This indicate Tx A-MPDU capability + u8 bCurrentAMPDUEnable; // This indicate Tx A-MPDU capability + u8 AMPDU_Factor; // This indicate Tx A-MPDU capability + u8 CurrentAMPDUFactor; // This indicate Tx A-MPDU capability + u8 MPDU_Density; // This indicate Tx A-MPDU capability + u8 CurrentMPDUDensity; // This indicate Tx A-MPDU capability + + // Forced A-MPDU enable + HT_AGGRE_MODE_E ForcedAMPDUMode; + u8 ForcedAMPDUFactor; + u8 ForcedMPDUDensity; + + // Forced A-MSDU enable + HT_AGGRE_MODE_E ForcedAMSDUMode; + u16 ForcedAMSDUMaxSize; + + u8 bForcedShortGI; + + u8 CurrentOpMode; + + // MIMO PS related + u8 SelfMimoPs; + u8 PeerMimoPs; + + // 40MHz Channel Offset settings. + HT_EXTCHNL_OFFSET CurSTAExtChnlOffset; + u8 bCurTxBW40MHz; // If we use 40 MHz to Tx + u8 PeerBandwidth; + + // For Bandwidth Switching + u8 bSwBwInProgress; + CHNLOP ChnlOp; // software switching channel in progress. By Bruce, 2008-02-15. + u8 SwBwStep; + //struct timer_list SwBwTimer; //moved to ieee80211_device. as timer_list need include some header file here. + + // For Realtek proprietary A-MPDU factor for aggregation + u8 bRegRT2RTAggregation; + u8 bCurrentRT2RTAggregation; + u8 bCurrentRT2RTLongSlotTime; + u8 szRT2RTAggBuffer[10]; + + // Rx Reorder control + u8 bRegRxReorderEnable; + u8 bCurRxReorderEnable; + u8 RxReorderWinSize; + u8 RxReorderPendingTime; + u16 RxReorderDropCounter; + +#ifdef USB_TX_DRIVER_AGGREGATION_ENABLE + u8 UsbTxAggrNum; +#endif +#ifdef USB_RX_AGGREGATION_SUPPORT + u8 UsbRxFwAggrEn; + u8 UsbRxFwAggrPageNum; + u8 UsbRxFwAggrPacketNum; + u8 UsbRxFwAggrTimeout; +#endif + + // Add for Broadcom(Linksys) IOT. Joseph + u8 bIsPeerBcm; + + // For IOT issue. + u8 IOTPeer; + u32 IOTAction; +} __attribute__ ((packed)) RT_HIGH_THROUGHPUT, *PRT_HIGH_THROUGHPUT; + + +//------------------------------------------------------------ +// The Data structure is used to keep HT related variable for "each Sta" +// when card is configured as "AP mode" +//------------------------------------------------------------ + +typedef struct _RT_HTINFO_STA_ENTRY{ + u8 bEnableHT; + + u8 bSupportCck; + + u16 AMSDU_MaxSize; + + u8 AMPDU_Factor; + u8 MPDU_Density; + + u8 HTHighestOperaRate; + + u8 bBw40MHz; + + u8 MimoPs; + + u8 McsRateSet[16]; + + +}RT_HTINFO_STA_ENTRY, *PRT_HTINFO_STA_ENTRY; + + + + + +//------------------------------------------------------------ +// The Data structure is used to keep HT related variable for "each AP" +// when card is configured as "STA mode" +//------------------------------------------------------------ + +typedef struct _BSS_HT{ + + u8 bdSupportHT; + + // HT related elements + u8 bdHTCapBuf[32]; + u16 bdHTCapLen; + u8 bdHTInfoBuf[32]; + u16 bdHTInfoLen; + + HT_SPEC_VER bdHTSpecVer; + //HT_CAPABILITY_ELE bdHTCapEle; + //HT_INFORMATION_ELE bdHTInfoEle; + + u8 bdRT2RTAggregation; + u8 bdRT2RTLongSlotTime; +} __attribute__ ((packed)) BSS_HT, *PBSS_HT; + +typedef struct _MIMO_RSSI{ + u32 EnableAntenna; + u32 AntennaA; + u32 AntennaB; + u32 AntennaC; + u32 AntennaD; + u32 Average; +}MIMO_RSSI, *PMIMO_RSSI; + +typedef struct _MIMO_EVM{ + u32 EVM1; + u32 EVM2; +}MIMO_EVM, *PMIMO_EVM; + +typedef struct _FALSE_ALARM_STATISTICS{ + u32 Cnt_Parity_Fail; + u32 Cnt_Rate_Illegal; + u32 Cnt_Crc8_fail; + u32 Cnt_all; +}FALSE_ALARM_STATISTICS, *PFALSE_ALARM_STATISTICS; + + +extern u8 MCS_FILTER_ALL[16]; +extern u8 MCS_FILTER_1SS[16]; + +/* 2007/07/11 MH Modify the macro. Becaus STA may link with a N-AP. If we set + STA in A/B/G mode and AP is still in N mode. The macro will be wrong. We have + to add a macro to judge wireless mode. */ +#define PICK_RATE(_nLegacyRate, _nMcsRate) \ + (_nMcsRate==0)?(_nLegacyRate&0x7f):(_nMcsRate) +/* 2007/07/12 MH We only define legacy and HT wireless mode now. */ +#define LEGACY_WIRELESS_MODE IEEE_MODE_MASK + +#define CURRENT_RATE(WirelessMode, LegacyRate, HTRate) \ + ((WirelessMode & (LEGACY_WIRELESS_MODE))!=0)?\ + (LegacyRate):\ + (PICK_RATE(LegacyRate, HTRate)) + + + +// MCS Bw 40 {1~7, 12~15,32} +#define RATE_ADPT_1SS_MASK 0xFF +#define RATE_ADPT_2SS_MASK 0xF0 //Skip MCS8~11 because mcs7 > mcs6, 9, 10, 11. 2007.01.16 by Emily +#define RATE_ADPT_MCS32_MASK 0x01 + +#define IS_11N_MCS_RATE(rate) (rate&0x80) + +typedef enum _HT_AGGRE_SIZE{ + HT_AGG_SIZE_8K = 0, + HT_AGG_SIZE_16K = 1, + HT_AGG_SIZE_32K = 2, + HT_AGG_SIZE_64K = 3, +}HT_AGGRE_SIZE_E, *PHT_AGGRE_SIZE_E; + +/* Indicate different AP vendor for IOT issue */ +typedef enum _HT_IOT_PEER +{ + HT_IOT_PEER_UNKNOWN = 0, + HT_IOT_PEER_REALTEK = 1, + HT_IOT_PEER_BROADCOM = 2, + HT_IOT_PEER_RALINK = 3, + HT_IOT_PEER_ATHEROS = 4, + HT_IOT_PEER_CISCO= 5, + HT_IOT_PEER_MAX = 6 +}HT_IOT_PEER_E, *PHTIOT_PEER_E; + +// +// IOT Action for different AP +// +typedef enum _HT_IOT_ACTION{ + HT_IOT_ACT_TX_USE_AMSDU_4K = 0x00000001, + HT_IOT_ACT_TX_USE_AMSDU_8K = 0x00000002, + HT_IOT_ACT_DISABLE_MCS14 = 0x00000004, + HT_IOT_ACT_DISABLE_MCS15 = 0x00000008, + HT_IOT_ACT_DISABLE_ALL_2SS = 0x00000010, + HT_IOT_ACT_DISABLE_EDCA_TURBO = 0x00000020, + HT_IOT_ACT_MGNT_USE_CCK_6M = 0x00000040, + HT_IOT_ACT_CDD_FSYNC = 0x00000080, + HT_IOT_ACT_PURE_N_MODE = 0x00000100, + HT_IOT_ACT_FORCED_CTS2SELF = 0x00000200, +}HT_IOT_ACTION_E, *PHT_IOT_ACTION_E; + +#endif //_RTL819XU_HTTYPE_H_