X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=kernel%2Fdrivers%2Fnet%2Ffddi%2FKconfig;fp=kernel%2Fdrivers%2Fnet%2Ffddi%2FKconfig;h=3a424c864f4dbfb9de66e1ecabda691c06dd7b20;hb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;hp=0000000000000000000000000000000000000000;hpb=98260f3884f4a202f9ca5eabed40b1354c489b29;p=kvmfornfv.git

diff --git a/kernel/drivers/net/fddi/Kconfig b/kernel/drivers/net/fddi/Kconfig
new file mode 100644
index 000000000..3a424c864
--- /dev/null
+++ b/kernel/drivers/net/fddi/Kconfig
@@ -0,0 +1,77 @@
+#
+# FDDI network device configuration
+#
+
+config FDDI
+	tristate "FDDI driver support"
+	depends on PCI || EISA || TC
+	---help---
+	  Fiber Distributed Data Interface is a high speed local area network
+	  design; essentially a replacement for high speed Ethernet. FDDI can
+	  run over copper or fiber. If you are connected to such a network and
+	  want a driver for the FDDI card in your computer, say Y here (and
+	  then also Y to the driver for your FDDI card, below). Most people
+	  will say N.
+
+if FDDI
+
+config DEFXX
+	tristate "Digital DEFTA/DEFEA/DEFPA adapter support"
+	depends on FDDI && (PCI || EISA || TC)
+	---help---
+	  This is support for the DIGITAL series of TURBOchannel (DEFTA),
+	  EISA (DEFEA) and PCI (DEFPA) controllers which can connect you
+	  to a local FDDI network.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called defxx.  If unsure, say N.
+
+config DEFXX_MMIO
+	bool
+	prompt "Use MMIO instead of PIO" if PCI || EISA
+	depends on DEFXX
+	default n if PCI || EISA
+	default y
+	---help---
+	  This instructs the driver to use EISA or PCI memory-mapped I/O
+	  (MMIO) as appropriate instead of programmed I/O ports (PIO).
+	  Enabling this gives an improvement in processing time in parts
+	  of the driver, but it may cause problems with EISA (DEFEA)
+	  adapters.  TURBOchannel does not have the concept of I/O ports,
+	  so MMIO is always used for these (DEFTA) adapters.
+
+	  If unsure, say N.
+
+config SKFP
+	tristate "SysKonnect FDDI PCI support"
+	depends on FDDI && PCI
+	select BITREVERSE
+	---help---
+	  Say Y here if you have a SysKonnect FDDI PCI adapter.
+	  The following adapters are supported by this driver:
+	  - SK-5521 (SK-NET FDDI-UP)
+	  - SK-5522 (SK-NET FDDI-UP DAS)
+	  - SK-5541 (SK-NET FDDI-FP)
+	  - SK-5543 (SK-NET FDDI-LP)
+	  - SK-5544 (SK-NET FDDI-LP DAS)
+	  - SK-5821 (SK-NET FDDI-UP64)
+	  - SK-5822 (SK-NET FDDI-UP64 DAS)
+	  - SK-5841 (SK-NET FDDI-FP64)
+	  - SK-5843 (SK-NET FDDI-LP64)
+	  - SK-5844 (SK-NET FDDI-LP64 DAS)
+	  - Netelligent 100 FDDI DAS Fibre SC
+	  - Netelligent 100 FDDI SAS Fibre SC
+	  - Netelligent 100 FDDI DAS UTP
+	  - Netelligent 100 FDDI SAS UTP
+	  - Netelligent 100 FDDI SAS Fibre MIC
+
+	  Read <file:Documentation/networking/skfp.txt> for information about
+	  the driver.
+
+	  Questions concerning this driver can be addressed to:
+	  <linux@syskonnect.de>
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called skfp.  This is recommended.
+
+endif # FDDI