X-Git-Url: https://gerrit.opnfv.org/gerrit/gitweb?a=blobdiff_plain;f=kernel%2Fdrivers%2Fnet%2Fethernet%2Fmicrel%2Fks8851.c;fp=kernel%2Fdrivers%2Fnet%2Fethernet%2Fmicrel%2Fks8851.c;h=66d4ab703f45a20b7949e1bd3e448c9dc182e68f;hb=9ca8dbcc65cfc63d6f5ef3312a33184e1d726e00;hp=0000000000000000000000000000000000000000;hpb=98260f3884f4a202f9ca5eabed40b1354c489b29;p=kvmfornfv.git diff --git a/kernel/drivers/net/ethernet/micrel/ks8851.c b/kernel/drivers/net/ethernet/micrel/ks8851.c new file mode 100644 index 000000000..66d4ab703 --- /dev/null +++ b/kernel/drivers/net/ethernet/micrel/ks8851.c @@ -0,0 +1,1623 @@ +/* drivers/net/ethernet/micrel/ks8851.c + * + * Copyright 2009 Simtec Electronics + * http://www.simtec.co.uk/ + * Ben Dooks + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#define DEBUG + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include + +#include "ks8851.h" + +/** + * struct ks8851_rxctrl - KS8851 driver rx control + * @mchash: Multicast hash-table data. + * @rxcr1: KS_RXCR1 register setting + * @rxcr2: KS_RXCR2 register setting + * + * Representation of the settings needs to control the receive filtering + * such as the multicast hash-filter and the receive register settings. This + * is used to make the job of working out if the receive settings change and + * then issuing the new settings to the worker that will send the necessary + * commands. + */ +struct ks8851_rxctrl { + u16 mchash[4]; + u16 rxcr1; + u16 rxcr2; +}; + +/** + * union ks8851_tx_hdr - tx header data + * @txb: The header as bytes + * @txw: The header as 16bit, little-endian words + * + * A dual representation of the tx header data to allow + * access to individual bytes, and to allow 16bit accesses + * with 16bit alignment. + */ +union ks8851_tx_hdr { + u8 txb[6]; + __le16 txw[3]; +}; + +/** + * struct ks8851_net - KS8851 driver private data + * @netdev: The network device we're bound to + * @spidev: The spi device we're bound to. + * @lock: Lock to ensure that the device is not accessed when busy. + * @statelock: Lock on this structure for tx list. + * @mii: The MII state information for the mii calls. + * @rxctrl: RX settings for @rxctrl_work. + * @tx_work: Work queue for tx packets + * @rxctrl_work: Work queue for updating RX mode and multicast lists + * @txq: Queue of packets for transmission. + * @spi_msg1: pre-setup SPI transfer with one message, @spi_xfer1. + * @spi_msg2: pre-setup SPI transfer with two messages, @spi_xfer2. + * @txh: Space for generating packet TX header in DMA-able data + * @rxd: Space for receiving SPI data, in DMA-able space. + * @txd: Space for transmitting SPI data, in DMA-able space. + * @msg_enable: The message flags controlling driver output (see ethtool). + * @fid: Incrementing frame id tag. + * @rc_ier: Cached copy of KS_IER. + * @rc_ccr: Cached copy of KS_CCR. + * @rc_rxqcr: Cached copy of KS_RXQCR. + * @eeprom_size: Companion eeprom size in Bytes, 0 if no eeprom + * @eeprom: 93CX6 EEPROM state for accessing on-board EEPROM. + * @vdd_reg: Optional regulator supplying the chip + * @vdd_io: Optional digital power supply for IO + * @gpio: Optional reset_n gpio + * + * The @lock ensures that the chip is protected when certain operations are + * in progress. When the read or write packet transfer is in progress, most + * of the chip registers are not ccessible until the transfer is finished and + * the DMA has been de-asserted. + * + * The @statelock is used to protect information in the structure which may + * need to be accessed via several sources, such as the network driver layer + * or one of the work queues. + * + * We align the buffers we may use for rx/tx to ensure that if the SPI driver + * wants to DMA map them, it will not have any problems with data the driver + * modifies. + */ +struct ks8851_net { + struct net_device *netdev; + struct spi_device *spidev; + struct mutex lock; + spinlock_t statelock; + + union ks8851_tx_hdr txh ____cacheline_aligned; + u8 rxd[8]; + u8 txd[8]; + + u32 msg_enable ____cacheline_aligned; + u16 tx_space; + u8 fid; + + u16 rc_ier; + u16 rc_rxqcr; + u16 rc_ccr; + u16 eeprom_size; + + struct mii_if_info mii; + struct ks8851_rxctrl rxctrl; + + struct work_struct tx_work; + struct work_struct rxctrl_work; + + struct sk_buff_head txq; + + struct spi_message spi_msg1; + struct spi_message spi_msg2; + struct spi_transfer spi_xfer1; + struct spi_transfer spi_xfer2[2]; + + struct eeprom_93cx6 eeprom; + struct regulator *vdd_reg; + struct regulator *vdd_io; + int gpio; +}; + +static int msg_enable; + +/* shift for byte-enable data */ +#define BYTE_EN(_x) ((_x) << 2) + +/* turn register number and byte-enable mask into data for start of packet */ +#define MK_OP(_byteen, _reg) (BYTE_EN(_byteen) | (_reg) << (8+2) | (_reg) >> 6) + +/* SPI register read/write calls. + * + * All these calls issue SPI transactions to access the chip's registers. They + * all require that the necessary lock is held to prevent accesses when the + * chip is busy transferring packet data (RX/TX FIFO accesses). + */ + +/** + * ks8851_wrreg16 - write 16bit register value to chip + * @ks: The chip state + * @reg: The register address + * @val: The value to write + * + * Issue a write to put the value @val into the register specified in @reg. + */ +static void ks8851_wrreg16(struct ks8851_net *ks, unsigned reg, unsigned val) +{ + struct spi_transfer *xfer = &ks->spi_xfer1; + struct spi_message *msg = &ks->spi_msg1; + __le16 txb[2]; + int ret; + + txb[0] = cpu_to_le16(MK_OP(reg & 2 ? 0xC : 0x03, reg) | KS_SPIOP_WR); + txb[1] = cpu_to_le16(val); + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 4; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + netdev_err(ks->netdev, "spi_sync() failed\n"); +} + +/** + * ks8851_wrreg8 - write 8bit register value to chip + * @ks: The chip state + * @reg: The register address + * @val: The value to write + * + * Issue a write to put the value @val into the register specified in @reg. + */ +static void ks8851_wrreg8(struct ks8851_net *ks, unsigned reg, unsigned val) +{ + struct spi_transfer *xfer = &ks->spi_xfer1; + struct spi_message *msg = &ks->spi_msg1; + __le16 txb[2]; + int ret; + int bit; + + bit = 1 << (reg & 3); + + txb[0] = cpu_to_le16(MK_OP(bit, reg) | KS_SPIOP_WR); + txb[1] = val; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 3; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + netdev_err(ks->netdev, "spi_sync() failed\n"); +} + +/** + * ks8851_rx_1msg - select whether to use one or two messages for spi read + * @ks: The device structure + * + * Return whether to generate a single message with a tx and rx buffer + * supplied to spi_sync(), or alternatively send the tx and rx buffers + * as separate messages. + * + * Depending on the hardware in use, a single message may be more efficient + * on interrupts or work done by the driver. + * + * This currently always returns true until we add some per-device data passed + * from the platform code to specify which mode is better. + */ +static inline bool ks8851_rx_1msg(struct ks8851_net *ks) +{ + return true; +} + +/** + * ks8851_rdreg - issue read register command and return the data + * @ks: The device state + * @op: The register address and byte enables in message format. + * @rxb: The RX buffer to return the result into + * @rxl: The length of data expected. + * + * This is the low level read call that issues the necessary spi message(s) + * to read data from the register specified in @op. + */ +static void ks8851_rdreg(struct ks8851_net *ks, unsigned op, + u8 *rxb, unsigned rxl) +{ + struct spi_transfer *xfer; + struct spi_message *msg; + __le16 *txb = (__le16 *)ks->txd; + u8 *trx = ks->rxd; + int ret; + + txb[0] = cpu_to_le16(op | KS_SPIOP_RD); + + if (ks8851_rx_1msg(ks)) { + msg = &ks->spi_msg1; + xfer = &ks->spi_xfer1; + + xfer->tx_buf = txb; + xfer->rx_buf = trx; + xfer->len = rxl + 2; + } else { + msg = &ks->spi_msg2; + xfer = ks->spi_xfer2; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 2; + + xfer++; + xfer->tx_buf = NULL; + xfer->rx_buf = trx; + xfer->len = rxl; + } + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + netdev_err(ks->netdev, "read: spi_sync() failed\n"); + else if (ks8851_rx_1msg(ks)) + memcpy(rxb, trx + 2, rxl); + else + memcpy(rxb, trx, rxl); +} + +/** + * ks8851_rdreg8 - read 8 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 8bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg8(struct ks8851_net *ks, unsigned reg) +{ + u8 rxb[1]; + + ks8851_rdreg(ks, MK_OP(1 << (reg & 3), reg), rxb, 1); + return rxb[0]; +} + +/** + * ks8851_rdreg16 - read 16 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 16bit register from the chip, returning the result +*/ +static unsigned ks8851_rdreg16(struct ks8851_net *ks, unsigned reg) +{ + __le16 rx = 0; + + ks8851_rdreg(ks, MK_OP(reg & 2 ? 0xC : 0x3, reg), (u8 *)&rx, 2); + return le16_to_cpu(rx); +} + +/** + * ks8851_rdreg32 - read 32 bit register from device + * @ks: The chip information + * @reg: The register address + * + * Read a 32bit register from the chip. + * + * Note, this read requires the address be aligned to 4 bytes. +*/ +static unsigned ks8851_rdreg32(struct ks8851_net *ks, unsigned reg) +{ + __le32 rx = 0; + + WARN_ON(reg & 3); + + ks8851_rdreg(ks, MK_OP(0xf, reg), (u8 *)&rx, 4); + return le32_to_cpu(rx); +} + +/** + * ks8851_soft_reset - issue one of the soft reset to the device + * @ks: The device state. + * @op: The bit(s) to set in the GRR + * + * Issue the relevant soft-reset command to the device's GRR register + * specified by @op. + * + * Note, the delays are in there as a caution to ensure that the reset + * has time to take effect and then complete. Since the datasheet does + * not currently specify the exact sequence, we have chosen something + * that seems to work with our device. + */ +static void ks8851_soft_reset(struct ks8851_net *ks, unsigned op) +{ + ks8851_wrreg16(ks, KS_GRR, op); + mdelay(1); /* wait a short time to effect reset */ + ks8851_wrreg16(ks, KS_GRR, 0); + mdelay(1); /* wait for condition to clear */ +} + +/** + * ks8851_set_powermode - set power mode of the device + * @ks: The device state + * @pwrmode: The power mode value to write to KS_PMECR. + * + * Change the power mode of the chip. + */ +static void ks8851_set_powermode(struct ks8851_net *ks, unsigned pwrmode) +{ + unsigned pmecr; + + netif_dbg(ks, hw, ks->netdev, "setting power mode %d\n", pwrmode); + + pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_PM_MASK; + pmecr |= pwrmode; + + ks8851_wrreg16(ks, KS_PMECR, pmecr); +} + +/** + * ks8851_write_mac_addr - write mac address to device registers + * @dev: The network device + * + * Update the KS8851 MAC address registers from the address in @dev. + * + * This call assumes that the chip is not running, so there is no need to + * shutdown the RXQ process whilst setting this. +*/ +static int ks8851_write_mac_addr(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + int i; + + mutex_lock(&ks->lock); + + /* + * Wake up chip in case it was powered off when stopped; otherwise, + * the first write to the MAC address does not take effect. + */ + ks8851_set_powermode(ks, PMECR_PM_NORMAL); + for (i = 0; i < ETH_ALEN; i++) + ks8851_wrreg8(ks, KS_MAR(i), dev->dev_addr[i]); + if (!netif_running(dev)) + ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + + mutex_unlock(&ks->lock); + + return 0; +} + +/** + * ks8851_read_mac_addr - read mac address from device registers + * @dev: The network device + * + * Update our copy of the KS8851 MAC address from the registers of @dev. +*/ +static void ks8851_read_mac_addr(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + int i; + + mutex_lock(&ks->lock); + + for (i = 0; i < ETH_ALEN; i++) + dev->dev_addr[i] = ks8851_rdreg8(ks, KS_MAR(i)); + + mutex_unlock(&ks->lock); +} + +/** + * ks8851_init_mac - initialise the mac address + * @ks: The device structure + * + * Get or create the initial mac address for the device and then set that + * into the station address register. If there is an EEPROM present, then + * we try that. If no valid mac address is found we use eth_random_addr() + * to create a new one. + */ +static void ks8851_init_mac(struct ks8851_net *ks) +{ + struct net_device *dev = ks->netdev; + + /* first, try reading what we've got already */ + if (ks->rc_ccr & CCR_EEPROM) { + ks8851_read_mac_addr(dev); + if (is_valid_ether_addr(dev->dev_addr)) + return; + + netdev_err(ks->netdev, "invalid mac address read %pM\n", + dev->dev_addr); + } + + eth_hw_addr_random(dev); + ks8851_write_mac_addr(dev); +} + +/** + * ks8851_rdfifo - read data from the receive fifo + * @ks: The device state. + * @buff: The buffer address + * @len: The length of the data to read + * + * Issue an RXQ FIFO read command and read the @len amount of data from + * the FIFO into the buffer specified by @buff. + */ +static void ks8851_rdfifo(struct ks8851_net *ks, u8 *buff, unsigned len) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + u8 txb[1]; + int ret; + + netif_dbg(ks, rx_status, ks->netdev, + "%s: %d@%p\n", __func__, len, buff); + + /* set the operation we're issuing */ + txb[0] = KS_SPIOP_RXFIFO; + + xfer->tx_buf = txb; + xfer->rx_buf = NULL; + xfer->len = 1; + + xfer++; + xfer->rx_buf = buff; + xfer->tx_buf = NULL; + xfer->len = len; + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_dbg_dumpkkt - dump initial packet contents to debug + * @ks: The device state + * @rxpkt: The data for the received packet + * + * Dump the initial data from the packet to dev_dbg(). +*/ +static void ks8851_dbg_dumpkkt(struct ks8851_net *ks, u8 *rxpkt) +{ + netdev_dbg(ks->netdev, + "pkt %02x%02x%02x%02x %02x%02x%02x%02x %02x%02x%02x%02x\n", + rxpkt[4], rxpkt[5], rxpkt[6], rxpkt[7], + rxpkt[8], rxpkt[9], rxpkt[10], rxpkt[11], + rxpkt[12], rxpkt[13], rxpkt[14], rxpkt[15]); +} + +/** + * ks8851_rx_pkts - receive packets from the host + * @ks: The device information. + * + * This is called from the IRQ work queue when the system detects that there + * are packets in the receive queue. Find out how many packets there are and + * read them from the FIFO. + */ +static void ks8851_rx_pkts(struct ks8851_net *ks) +{ + struct sk_buff *skb; + unsigned rxfc; + unsigned rxlen; + unsigned rxstat; + u32 rxh; + u8 *rxpkt; + + rxfc = ks8851_rdreg8(ks, KS_RXFC); + + netif_dbg(ks, rx_status, ks->netdev, + "%s: %d packets\n", __func__, rxfc); + + /* Currently we're issuing a read per packet, but we could possibly + * improve the code by issuing a single read, getting the receive + * header, allocating the packet and then reading the packet data + * out in one go. + * + * This form of operation would require us to hold the SPI bus' + * chipselect low during the entie transaction to avoid any + * reset to the data stream coming from the chip. + */ + + for (; rxfc != 0; rxfc--) { + rxh = ks8851_rdreg32(ks, KS_RXFHSR); + rxstat = rxh & 0xffff; + rxlen = (rxh >> 16) & 0xfff; + + netif_dbg(ks, rx_status, ks->netdev, + "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen); + + /* the length of the packet includes the 32bit CRC */ + + /* set dma read address */ + ks8851_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI | 0x00); + + /* start the packet dma process, and set auto-dequeue rx */ + ks8851_wrreg16(ks, KS_RXQCR, + ks->rc_rxqcr | RXQCR_SDA | RXQCR_ADRFE); + + if (rxlen > 4) { + unsigned int rxalign; + + rxlen -= 4; + rxalign = ALIGN(rxlen, 4); + skb = netdev_alloc_skb_ip_align(ks->netdev, rxalign); + if (skb) { + + /* 4 bytes of status header + 4 bytes of + * garbage: we put them before ethernet + * header, so that they are copied, + * but ignored. + */ + + rxpkt = skb_put(skb, rxlen) - 8; + + ks8851_rdfifo(ks, rxpkt, rxalign + 8); + + if (netif_msg_pktdata(ks)) + ks8851_dbg_dumpkkt(ks, rxpkt); + + skb->protocol = eth_type_trans(skb, ks->netdev); + netif_rx_ni(skb); + + ks->netdev->stats.rx_packets++; + ks->netdev->stats.rx_bytes += rxlen; + } + } + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + } +} + +/** + * ks8851_irq - IRQ handler for dealing with interrupt requests + * @irq: IRQ number + * @_ks: cookie + * + * This handler is invoked when the IRQ line asserts to find out what happened. + * As we cannot allow ourselves to sleep in HARDIRQ context, this handler runs + * in thread context. + * + * Read the interrupt status, work out what needs to be done and then clear + * any of the interrupts that are not needed. + */ +static irqreturn_t ks8851_irq(int irq, void *_ks) +{ + struct ks8851_net *ks = _ks; + unsigned status; + unsigned handled = 0; + + mutex_lock(&ks->lock); + + status = ks8851_rdreg16(ks, KS_ISR); + + netif_dbg(ks, intr, ks->netdev, + "%s: status 0x%04x\n", __func__, status); + + if (status & IRQ_LCI) + handled |= IRQ_LCI; + + if (status & IRQ_LDI) { + u16 pmecr = ks8851_rdreg16(ks, KS_PMECR); + pmecr &= ~PMECR_WKEVT_MASK; + ks8851_wrreg16(ks, KS_PMECR, pmecr | PMECR_WKEVT_LINK); + + handled |= IRQ_LDI; + } + + if (status & IRQ_RXPSI) + handled |= IRQ_RXPSI; + + if (status & IRQ_TXI) { + handled |= IRQ_TXI; + + /* no lock here, tx queue should have been stopped */ + + /* update our idea of how much tx space is available to the + * system */ + ks->tx_space = ks8851_rdreg16(ks, KS_TXMIR); + + netif_dbg(ks, intr, ks->netdev, + "%s: txspace %d\n", __func__, ks->tx_space); + } + + if (status & IRQ_RXI) + handled |= IRQ_RXI; + + if (status & IRQ_SPIBEI) { + dev_err(&ks->spidev->dev, "%s: spi bus error\n", __func__); + handled |= IRQ_SPIBEI; + } + + ks8851_wrreg16(ks, KS_ISR, handled); + + if (status & IRQ_RXI) { + /* the datasheet says to disable the rx interrupt during + * packet read-out, however we're masking the interrupt + * from the device so do not bother masking just the RX + * from the device. */ + + ks8851_rx_pkts(ks); + } + + /* if something stopped the rx process, probably due to wanting + * to change the rx settings, then do something about restarting + * it. */ + if (status & IRQ_RXPSI) { + struct ks8851_rxctrl *rxc = &ks->rxctrl; + + /* update the multicast hash table */ + ks8851_wrreg16(ks, KS_MAHTR0, rxc->mchash[0]); + ks8851_wrreg16(ks, KS_MAHTR1, rxc->mchash[1]); + ks8851_wrreg16(ks, KS_MAHTR2, rxc->mchash[2]); + ks8851_wrreg16(ks, KS_MAHTR3, rxc->mchash[3]); + + ks8851_wrreg16(ks, KS_RXCR2, rxc->rxcr2); + ks8851_wrreg16(ks, KS_RXCR1, rxc->rxcr1); + } + + mutex_unlock(&ks->lock); + + if (status & IRQ_LCI) + mii_check_link(&ks->mii); + + if (status & IRQ_TXI) + netif_wake_queue(ks->netdev); + + return IRQ_HANDLED; +} + +/** + * calc_txlen - calculate size of message to send packet + * @len: Length of data + * + * Returns the size of the TXFIFO message needed to send + * this packet. + */ +static inline unsigned calc_txlen(unsigned len) +{ + return ALIGN(len + 4, 4); +} + +/** + * ks8851_wrpkt - write packet to TX FIFO + * @ks: The device state. + * @txp: The sk_buff to transmit. + * @irq: IRQ on completion of the packet. + * + * Send the @txp to the chip. This means creating the relevant packet header + * specifying the length of the packet and the other information the chip + * needs, such as IRQ on completion. Send the header and the packet data to + * the device. + */ +static void ks8851_wrpkt(struct ks8851_net *ks, struct sk_buff *txp, bool irq) +{ + struct spi_transfer *xfer = ks->spi_xfer2; + struct spi_message *msg = &ks->spi_msg2; + unsigned fid = 0; + int ret; + + netif_dbg(ks, tx_queued, ks->netdev, "%s: skb %p, %d@%p, irq %d\n", + __func__, txp, txp->len, txp->data, irq); + + fid = ks->fid++; + fid &= TXFR_TXFID_MASK; + + if (irq) + fid |= TXFR_TXIC; /* irq on completion */ + + /* start header at txb[1] to align txw entries */ + ks->txh.txb[1] = KS_SPIOP_TXFIFO; + ks->txh.txw[1] = cpu_to_le16(fid); + ks->txh.txw[2] = cpu_to_le16(txp->len); + + xfer->tx_buf = &ks->txh.txb[1]; + xfer->rx_buf = NULL; + xfer->len = 5; + + xfer++; + xfer->tx_buf = txp->data; + xfer->rx_buf = NULL; + xfer->len = ALIGN(txp->len, 4); + + ret = spi_sync(ks->spidev, msg); + if (ret < 0) + netdev_err(ks->netdev, "%s: spi_sync() failed\n", __func__); +} + +/** + * ks8851_done_tx - update and then free skbuff after transmitting + * @ks: The device state + * @txb: The buffer transmitted + */ +static void ks8851_done_tx(struct ks8851_net *ks, struct sk_buff *txb) +{ + struct net_device *dev = ks->netdev; + + dev->stats.tx_bytes += txb->len; + dev->stats.tx_packets++; + + dev_kfree_skb(txb); +} + +/** + * ks8851_tx_work - process tx packet(s) + * @work: The work strucutre what was scheduled. + * + * This is called when a number of packets have been scheduled for + * transmission and need to be sent to the device. + */ +static void ks8851_tx_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, tx_work); + struct sk_buff *txb; + bool last = skb_queue_empty(&ks->txq); + + mutex_lock(&ks->lock); + + while (!last) { + txb = skb_dequeue(&ks->txq); + last = skb_queue_empty(&ks->txq); + + if (txb != NULL) { + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA); + ks8851_wrpkt(ks, txb, last); + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + ks8851_wrreg16(ks, KS_TXQCR, TXQCR_METFE); + + ks8851_done_tx(ks, txb); + } + } + + mutex_unlock(&ks->lock); +} + +/** + * ks8851_net_open - open network device + * @dev: The network device being opened. + * + * Called when the network device is marked active, such as a user executing + * 'ifconfig up' on the device. + */ +static int ks8851_net_open(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + /* lock the card, even if we may not actually be doing anything + * else at the moment */ + mutex_lock(&ks->lock); + + netif_dbg(ks, ifup, ks->netdev, "opening\n"); + + /* bring chip out of any power saving mode it was in */ + ks8851_set_powermode(ks, PMECR_PM_NORMAL); + + /* issue a soft reset to the RX/TX QMU to put it into a known + * state. */ + ks8851_soft_reset(ks, GRR_QMU); + + /* setup transmission parameters */ + + ks8851_wrreg16(ks, KS_TXCR, (TXCR_TXE | /* enable transmit process */ + TXCR_TXPE | /* pad to min length */ + TXCR_TXCRC | /* add CRC */ + TXCR_TXFCE)); /* enable flow control */ + + /* auto-increment tx data, reset tx pointer */ + ks8851_wrreg16(ks, KS_TXFDPR, TXFDPR_TXFPAI); + + /* setup receiver control */ + + ks8851_wrreg16(ks, KS_RXCR1, (RXCR1_RXPAFMA | /* from mac filter */ + RXCR1_RXFCE | /* enable flow control */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXUE | /* unicast enable */ + RXCR1_RXE)); /* enable rx block */ + + /* transfer entire frames out in one go */ + ks8851_wrreg16(ks, KS_RXCR2, RXCR2_SRDBL_FRAME); + + /* set receive counter timeouts */ + ks8851_wrreg16(ks, KS_RXDTTR, 1000); /* 1ms after first frame to IRQ */ + ks8851_wrreg16(ks, KS_RXDBCTR, 4096); /* >4Kbytes in buffer to IRQ */ + ks8851_wrreg16(ks, KS_RXFCTR, 10); /* 10 frames to IRQ */ + + ks->rc_rxqcr = (RXQCR_RXFCTE | /* IRQ on frame count exceeded */ + RXQCR_RXDBCTE | /* IRQ on byte count exceeded */ + RXQCR_RXDTTE); /* IRQ on time exceeded */ + + ks8851_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr); + + /* clear then enable interrupts */ + +#define STD_IRQ (IRQ_LCI | /* Link Change */ \ + IRQ_TXI | /* TX done */ \ + IRQ_RXI | /* RX done */ \ + IRQ_SPIBEI | /* SPI bus error */ \ + IRQ_TXPSI | /* TX process stop */ \ + IRQ_RXPSI) /* RX process stop */ + + ks->rc_ier = STD_IRQ; + ks8851_wrreg16(ks, KS_ISR, STD_IRQ); + ks8851_wrreg16(ks, KS_IER, STD_IRQ); + + netif_start_queue(ks->netdev); + + netif_dbg(ks, ifup, ks->netdev, "network device up\n"); + + mutex_unlock(&ks->lock); + return 0; +} + +/** + * ks8851_net_stop - close network device + * @dev: The device being closed. + * + * Called to close down a network device which has been active. Cancell any + * work, shutdown the RX and TX process and then place the chip into a low + * power state whilst it is not being used. + */ +static int ks8851_net_stop(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + netif_info(ks, ifdown, dev, "shutting down\n"); + + netif_stop_queue(dev); + + mutex_lock(&ks->lock); + /* turn off the IRQs and ack any outstanding */ + ks8851_wrreg16(ks, KS_IER, 0x0000); + ks8851_wrreg16(ks, KS_ISR, 0xffff); + mutex_unlock(&ks->lock); + + /* stop any outstanding work */ + flush_work(&ks->tx_work); + flush_work(&ks->rxctrl_work); + + mutex_lock(&ks->lock); + /* shutdown RX process */ + ks8851_wrreg16(ks, KS_RXCR1, 0x0000); + + /* shutdown TX process */ + ks8851_wrreg16(ks, KS_TXCR, 0x0000); + + /* set powermode to soft power down to save power */ + ks8851_set_powermode(ks, PMECR_PM_SOFTDOWN); + mutex_unlock(&ks->lock); + + /* ensure any queued tx buffers are dumped */ + while (!skb_queue_empty(&ks->txq)) { + struct sk_buff *txb = skb_dequeue(&ks->txq); + + netif_dbg(ks, ifdown, ks->netdev, + "%s: freeing txb %p\n", __func__, txb); + + dev_kfree_skb(txb); + } + + return 0; +} + +/** + * ks8851_start_xmit - transmit packet + * @skb: The buffer to transmit + * @dev: The device used to transmit the packet. + * + * Called by the network layer to transmit the @skb. Queue the packet for + * the device and schedule the necessary work to transmit the packet when + * it is free. + * + * We do this to firstly avoid sleeping with the network device locked, + * and secondly so we can round up more than one packet to transmit which + * means we can try and avoid generating too many transmit done interrupts. + */ +static netdev_tx_t ks8851_start_xmit(struct sk_buff *skb, + struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + unsigned needed = calc_txlen(skb->len); + netdev_tx_t ret = NETDEV_TX_OK; + + netif_dbg(ks, tx_queued, ks->netdev, + "%s: skb %p, %d@%p\n", __func__, skb, skb->len, skb->data); + + spin_lock(&ks->statelock); + + if (needed > ks->tx_space) { + netif_stop_queue(dev); + ret = NETDEV_TX_BUSY; + } else { + ks->tx_space -= needed; + skb_queue_tail(&ks->txq, skb); + } + + spin_unlock(&ks->statelock); + schedule_work(&ks->tx_work); + + return ret; +} + +/** + * ks8851_rxctrl_work - work handler to change rx mode + * @work: The work structure this belongs to. + * + * Lock the device and issue the necessary changes to the receive mode from + * the network device layer. This is done so that we can do this without + * having to sleep whilst holding the network device lock. + * + * Since the recommendation from Micrel is that the RXQ is shutdown whilst the + * receive parameters are programmed, we issue a write to disable the RXQ and + * then wait for the interrupt handler to be triggered once the RXQ shutdown is + * complete. The interrupt handler then writes the new values into the chip. + */ +static void ks8851_rxctrl_work(struct work_struct *work) +{ + struct ks8851_net *ks = container_of(work, struct ks8851_net, rxctrl_work); + + mutex_lock(&ks->lock); + + /* need to shutdown RXQ before modifying filter parameters */ + ks8851_wrreg16(ks, KS_RXCR1, 0x00); + + mutex_unlock(&ks->lock); +} + +static void ks8851_set_rx_mode(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + struct ks8851_rxctrl rxctrl; + + memset(&rxctrl, 0, sizeof(rxctrl)); + + if (dev->flags & IFF_PROMISC) { + /* interface to receive everything */ + + rxctrl.rxcr1 = RXCR1_RXAE | RXCR1_RXINVF; + } else if (dev->flags & IFF_ALLMULTI) { + /* accept all multicast packets */ + + rxctrl.rxcr1 = (RXCR1_RXME | RXCR1_RXAE | + RXCR1_RXPAFMA | RXCR1_RXMAFMA); + } else if (dev->flags & IFF_MULTICAST && !netdev_mc_empty(dev)) { + struct netdev_hw_addr *ha; + u32 crc; + + /* accept some multicast */ + + netdev_for_each_mc_addr(ha, dev) { + crc = ether_crc(ETH_ALEN, ha->addr); + crc >>= (32 - 6); /* get top six bits */ + + rxctrl.mchash[crc >> 4] |= (1 << (crc & 0xf)); + } + + rxctrl.rxcr1 = RXCR1_RXME | RXCR1_RXPAFMA; + } else { + /* just accept broadcast / unicast */ + rxctrl.rxcr1 = RXCR1_RXPAFMA; + } + + rxctrl.rxcr1 |= (RXCR1_RXUE | /* unicast enable */ + RXCR1_RXBE | /* broadcast enable */ + RXCR1_RXE | /* RX process enable */ + RXCR1_RXFCE); /* enable flow control */ + + rxctrl.rxcr2 |= RXCR2_SRDBL_FRAME; + + /* schedule work to do the actual set of the data if needed */ + + spin_lock(&ks->statelock); + + if (memcmp(&rxctrl, &ks->rxctrl, sizeof(rxctrl)) != 0) { + memcpy(&ks->rxctrl, &rxctrl, sizeof(ks->rxctrl)); + schedule_work(&ks->rxctrl_work); + } + + spin_unlock(&ks->statelock); +} + +static int ks8851_set_mac_address(struct net_device *dev, void *addr) +{ + struct sockaddr *sa = addr; + + if (netif_running(dev)) + return -EBUSY; + + if (!is_valid_ether_addr(sa->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, sa->sa_data, ETH_ALEN); + return ks8851_write_mac_addr(dev); +} + +static int ks8851_net_ioctl(struct net_device *dev, struct ifreq *req, int cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + + if (!netif_running(dev)) + return -EINVAL; + + return generic_mii_ioctl(&ks->mii, if_mii(req), cmd, NULL); +} + +static const struct net_device_ops ks8851_netdev_ops = { + .ndo_open = ks8851_net_open, + .ndo_stop = ks8851_net_stop, + .ndo_do_ioctl = ks8851_net_ioctl, + .ndo_start_xmit = ks8851_start_xmit, + .ndo_set_mac_address = ks8851_set_mac_address, + .ndo_set_rx_mode = ks8851_set_rx_mode, + .ndo_change_mtu = eth_change_mtu, + .ndo_validate_addr = eth_validate_addr, +}; + +/* ethtool support */ + +static void ks8851_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *di) +{ + strlcpy(di->driver, "KS8851", sizeof(di->driver)); + strlcpy(di->version, "1.00", sizeof(di->version)); + strlcpy(di->bus_info, dev_name(dev->dev.parent), sizeof(di->bus_info)); +} + +static u32 ks8851_get_msglevel(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return ks->msg_enable; +} + +static void ks8851_set_msglevel(struct net_device *dev, u32 to) +{ + struct ks8851_net *ks = netdev_priv(dev); + ks->msg_enable = to; +} + +static int ks8851_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_gset(&ks->mii, cmd); +} + +static int ks8851_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_ethtool_sset(&ks->mii, cmd); +} + +static u32 ks8851_get_link(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_link_ok(&ks->mii); +} + +static int ks8851_nway_reset(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + return mii_nway_restart(&ks->mii); +} + +/* EEPROM support */ + +static void ks8851_eeprom_regread(struct eeprom_93cx6 *ee) +{ + struct ks8851_net *ks = ee->data; + unsigned val; + + val = ks8851_rdreg16(ks, KS_EEPCR); + + ee->reg_data_out = (val & EEPCR_EESB) ? 1 : 0; + ee->reg_data_clock = (val & EEPCR_EESCK) ? 1 : 0; + ee->reg_chip_select = (val & EEPCR_EECS) ? 1 : 0; +} + +static void ks8851_eeprom_regwrite(struct eeprom_93cx6 *ee) +{ + struct ks8851_net *ks = ee->data; + unsigned val = EEPCR_EESA; /* default - eeprom access on */ + + if (ee->drive_data) + val |= EEPCR_EESRWA; + if (ee->reg_data_in) + val |= EEPCR_EEDO; + if (ee->reg_data_clock) + val |= EEPCR_EESCK; + if (ee->reg_chip_select) + val |= EEPCR_EECS; + + ks8851_wrreg16(ks, KS_EEPCR, val); +} + +/** + * ks8851_eeprom_claim - claim device EEPROM and activate the interface + * @ks: The network device state. + * + * Check for the presence of an EEPROM, and then activate software access + * to the device. + */ +static int ks8851_eeprom_claim(struct ks8851_net *ks) +{ + if (!(ks->rc_ccr & CCR_EEPROM)) + return -ENOENT; + + mutex_lock(&ks->lock); + + /* start with clock low, cs high */ + ks8851_wrreg16(ks, KS_EEPCR, EEPCR_EESA | EEPCR_EECS); + return 0; +} + +/** + * ks8851_eeprom_release - release the EEPROM interface + * @ks: The device state + * + * Release the software access to the device EEPROM + */ +static void ks8851_eeprom_release(struct ks8851_net *ks) +{ + unsigned val = ks8851_rdreg16(ks, KS_EEPCR); + + ks8851_wrreg16(ks, KS_EEPCR, val & ~EEPCR_EESA); + mutex_unlock(&ks->lock); +} + +#define KS_EEPROM_MAGIC (0x00008851) + +static int ks8851_set_eeprom(struct net_device *dev, + struct ethtool_eeprom *ee, u8 *data) +{ + struct ks8851_net *ks = netdev_priv(dev); + int offset = ee->offset; + int len = ee->len; + u16 tmp; + + /* currently only support byte writing */ + if (len != 1) + return -EINVAL; + + if (ee->magic != KS_EEPROM_MAGIC) + return -EINVAL; + + if (ks8851_eeprom_claim(ks)) + return -ENOENT; + + eeprom_93cx6_wren(&ks->eeprom, true); + + /* ethtool currently only supports writing bytes, which means + * we have to read/modify/write our 16bit EEPROMs */ + + eeprom_93cx6_read(&ks->eeprom, offset/2, &tmp); + + if (offset & 1) { + tmp &= 0xff; + tmp |= *data << 8; + } else { + tmp &= 0xff00; + tmp |= *data; + } + + eeprom_93cx6_write(&ks->eeprom, offset/2, tmp); + eeprom_93cx6_wren(&ks->eeprom, false); + + ks8851_eeprom_release(ks); + + return 0; +} + +static int ks8851_get_eeprom(struct net_device *dev, + struct ethtool_eeprom *ee, u8 *data) +{ + struct ks8851_net *ks = netdev_priv(dev); + int offset = ee->offset; + int len = ee->len; + + /* must be 2 byte aligned */ + if (len & 1 || offset & 1) + return -EINVAL; + + if (ks8851_eeprom_claim(ks)) + return -ENOENT; + + ee->magic = KS_EEPROM_MAGIC; + + eeprom_93cx6_multiread(&ks->eeprom, offset/2, (__le16 *)data, len/2); + ks8851_eeprom_release(ks); + + return 0; +} + +static int ks8851_get_eeprom_len(struct net_device *dev) +{ + struct ks8851_net *ks = netdev_priv(dev); + + /* currently, we assume it is an 93C46 attached, so return 128 */ + return ks->rc_ccr & CCR_EEPROM ? 128 : 0; +} + +static const struct ethtool_ops ks8851_ethtool_ops = { + .get_drvinfo = ks8851_get_drvinfo, + .get_msglevel = ks8851_get_msglevel, + .set_msglevel = ks8851_set_msglevel, + .get_settings = ks8851_get_settings, + .set_settings = ks8851_set_settings, + .get_link = ks8851_get_link, + .nway_reset = ks8851_nway_reset, + .get_eeprom_len = ks8851_get_eeprom_len, + .get_eeprom = ks8851_get_eeprom, + .set_eeprom = ks8851_set_eeprom, +}; + +/* MII interface controls */ + +/** + * ks8851_phy_reg - convert MII register into a KS8851 register + * @reg: MII register number. + * + * Return the KS8851 register number for the corresponding MII PHY register + * if possible. Return zero if the MII register has no direct mapping to the + * KS8851 register set. + */ +static int ks8851_phy_reg(int reg) +{ + switch (reg) { + case MII_BMCR: + return KS_P1MBCR; + case MII_BMSR: + return KS_P1MBSR; + case MII_PHYSID1: + return KS_PHY1ILR; + case MII_PHYSID2: + return KS_PHY1IHR; + case MII_ADVERTISE: + return KS_P1ANAR; + case MII_LPA: + return KS_P1ANLPR; + } + + return 0x0; +} + +/** + * ks8851_phy_read - MII interface PHY register read. + * @dev: The network device the PHY is on. + * @phy_addr: Address of PHY (ignored as we only have one) + * @reg: The register to read. + * + * This call reads data from the PHY register specified in @reg. Since the + * device does not support all the MII registers, the non-existent values + * are always returned as zero. + * + * We return zero for unsupported registers as the MII code does not check + * the value returned for any error status, and simply returns it to the + * caller. The mii-tool that the driver was tested with takes any -ve error + * as real PHY capabilities, thus displaying incorrect data to the user. + */ +static int ks8851_phy_read(struct net_device *dev, int phy_addr, int reg) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + int result; + + ksreg = ks8851_phy_reg(reg); + if (!ksreg) + return 0x0; /* no error return allowed, so use zero */ + + mutex_lock(&ks->lock); + result = ks8851_rdreg16(ks, ksreg); + mutex_unlock(&ks->lock); + + return result; +} + +static void ks8851_phy_write(struct net_device *dev, + int phy, int reg, int value) +{ + struct ks8851_net *ks = netdev_priv(dev); + int ksreg; + + ksreg = ks8851_phy_reg(reg); + if (ksreg) { + mutex_lock(&ks->lock); + ks8851_wrreg16(ks, ksreg, value); + mutex_unlock(&ks->lock); + } +} + +/** + * ks8851_read_selftest - read the selftest memory info. + * @ks: The device state + * + * Read and check the TX/RX memory selftest information. + */ +static int ks8851_read_selftest(struct ks8851_net *ks) +{ + unsigned both_done = MBIR_TXMBF | MBIR_RXMBF; + int ret = 0; + unsigned rd; + + rd = ks8851_rdreg16(ks, KS_MBIR); + + if ((rd & both_done) != both_done) { + netdev_warn(ks->netdev, "Memory selftest not finished\n"); + return 0; + } + + if (rd & MBIR_TXMBFA) { + netdev_err(ks->netdev, "TX memory selftest fail\n"); + ret |= 1; + } + + if (rd & MBIR_RXMBFA) { + netdev_err(ks->netdev, "RX memory selftest fail\n"); + ret |= 2; + } + + return 0; +} + +/* driver bus management functions */ + +#ifdef CONFIG_PM_SLEEP + +static int ks8851_suspend(struct device *dev) +{ + struct ks8851_net *ks = dev_get_drvdata(dev); + struct net_device *netdev = ks->netdev; + + if (netif_running(netdev)) { + netif_device_detach(netdev); + ks8851_net_stop(netdev); + } + + return 0; +} + +static int ks8851_resume(struct device *dev) +{ + struct ks8851_net *ks = dev_get_drvdata(dev); + struct net_device *netdev = ks->netdev; + + if (netif_running(netdev)) { + ks8851_net_open(netdev); + netif_device_attach(netdev); + } + + return 0; +} +#endif + +static SIMPLE_DEV_PM_OPS(ks8851_pm_ops, ks8851_suspend, ks8851_resume); + +static int ks8851_probe(struct spi_device *spi) +{ + struct net_device *ndev; + struct ks8851_net *ks; + int ret; + unsigned cider; + int gpio; + + ndev = alloc_etherdev(sizeof(struct ks8851_net)); + if (!ndev) + return -ENOMEM; + + spi->bits_per_word = 8; + + ks = netdev_priv(ndev); + + ks->netdev = ndev; + ks->spidev = spi; + ks->tx_space = 6144; + + gpio = of_get_named_gpio_flags(spi->dev.of_node, "reset-gpios", + 0, NULL); + if (gpio == -EPROBE_DEFER) { + ret = gpio; + goto err_gpio; + } + + ks->gpio = gpio; + if (gpio_is_valid(gpio)) { + ret = devm_gpio_request_one(&spi->dev, gpio, + GPIOF_OUT_INIT_LOW, "ks8851_rst_n"); + if (ret) { + dev_err(&spi->dev, "reset gpio request failed\n"); + goto err_gpio; + } + } + + ks->vdd_io = devm_regulator_get(&spi->dev, "vdd-io"); + if (IS_ERR(ks->vdd_io)) { + ret = PTR_ERR(ks->vdd_io); + goto err_reg_io; + } + + ret = regulator_enable(ks->vdd_io); + if (ret) { + dev_err(&spi->dev, "regulator vdd_io enable fail: %d\n", + ret); + goto err_reg_io; + } + + ks->vdd_reg = devm_regulator_get(&spi->dev, "vdd"); + if (IS_ERR(ks->vdd_reg)) { + ret = PTR_ERR(ks->vdd_reg); + goto err_reg; + } + + ret = regulator_enable(ks->vdd_reg); + if (ret) { + dev_err(&spi->dev, "regulator vdd enable fail: %d\n", + ret); + goto err_reg; + } + + if (gpio_is_valid(gpio)) { + usleep_range(10000, 11000); + gpio_set_value(gpio, 1); + } + + mutex_init(&ks->lock); + spin_lock_init(&ks->statelock); + + INIT_WORK(&ks->tx_work, ks8851_tx_work); + INIT_WORK(&ks->rxctrl_work, ks8851_rxctrl_work); + + /* initialise pre-made spi transfer messages */ + + spi_message_init(&ks->spi_msg1); + spi_message_add_tail(&ks->spi_xfer1, &ks->spi_msg1); + + spi_message_init(&ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[0], &ks->spi_msg2); + spi_message_add_tail(&ks->spi_xfer2[1], &ks->spi_msg2); + + /* setup EEPROM state */ + + ks->eeprom.data = ks; + ks->eeprom.width = PCI_EEPROM_WIDTH_93C46; + ks->eeprom.register_read = ks8851_eeprom_regread; + ks->eeprom.register_write = ks8851_eeprom_regwrite; + + /* setup mii state */ + ks->mii.dev = ndev; + ks->mii.phy_id = 1, + ks->mii.phy_id_mask = 1; + ks->mii.reg_num_mask = 0xf; + ks->mii.mdio_read = ks8851_phy_read; + ks->mii.mdio_write = ks8851_phy_write; + + dev_info(&spi->dev, "message enable is %d\n", msg_enable); + + /* set the default message enable */ + ks->msg_enable = netif_msg_init(msg_enable, (NETIF_MSG_DRV | + NETIF_MSG_PROBE | + NETIF_MSG_LINK)); + + skb_queue_head_init(&ks->txq); + + ndev->ethtool_ops = &ks8851_ethtool_ops; + SET_NETDEV_DEV(ndev, &spi->dev); + + spi_set_drvdata(spi, ks); + + ndev->if_port = IF_PORT_100BASET; + ndev->netdev_ops = &ks8851_netdev_ops; + ndev->irq = spi->irq; + + /* issue a global soft reset to reset the device. */ + ks8851_soft_reset(ks, GRR_GSR); + + /* simple check for a valid chip being connected to the bus */ + cider = ks8851_rdreg16(ks, KS_CIDER); + if ((cider & ~CIDER_REV_MASK) != CIDER_ID) { + dev_err(&spi->dev, "failed to read device ID\n"); + ret = -ENODEV; + goto err_id; + } + + /* cache the contents of the CCR register for EEPROM, etc. */ + ks->rc_ccr = ks8851_rdreg16(ks, KS_CCR); + + if (ks->rc_ccr & CCR_EEPROM) + ks->eeprom_size = 128; + else + ks->eeprom_size = 0; + + ks8851_read_selftest(ks); + ks8851_init_mac(ks); + + ret = request_threaded_irq(spi->irq, NULL, ks8851_irq, + IRQF_TRIGGER_LOW | IRQF_ONESHOT, + ndev->name, ks); + if (ret < 0) { + dev_err(&spi->dev, "failed to get irq\n"); + goto err_irq; + } + + ret = register_netdev(ndev); + if (ret) { + dev_err(&spi->dev, "failed to register network device\n"); + goto err_netdev; + } + + netdev_info(ndev, "revision %d, MAC %pM, IRQ %d, %s EEPROM\n", + CIDER_REV_GET(cider), ndev->dev_addr, ndev->irq, + ks->rc_ccr & CCR_EEPROM ? "has" : "no"); + + return 0; + + +err_netdev: + free_irq(ndev->irq, ks); + +err_irq: + if (gpio_is_valid(gpio)) + gpio_set_value(gpio, 0); +err_id: + regulator_disable(ks->vdd_reg); +err_reg: + regulator_disable(ks->vdd_io); +err_reg_io: +err_gpio: + free_netdev(ndev); + return ret; +} + +static int ks8851_remove(struct spi_device *spi) +{ + struct ks8851_net *priv = spi_get_drvdata(spi); + + if (netif_msg_drv(priv)) + dev_info(&spi->dev, "remove\n"); + + unregister_netdev(priv->netdev); + free_irq(spi->irq, priv); + if (gpio_is_valid(priv->gpio)) + gpio_set_value(priv->gpio, 0); + regulator_disable(priv->vdd_reg); + regulator_disable(priv->vdd_io); + free_netdev(priv->netdev); + + return 0; +} + +static const struct of_device_id ks8851_match_table[] = { + { .compatible = "micrel,ks8851" }, + { } +}; + +static struct spi_driver ks8851_driver = { + .driver = { + .name = "ks8851", + .of_match_table = ks8851_match_table, + .owner = THIS_MODULE, + .pm = &ks8851_pm_ops, + }, + .probe = ks8851_probe, + .remove = ks8851_remove, +}; +module_spi_driver(ks8851_driver); + +MODULE_DESCRIPTION("KS8851 Network driver"); +MODULE_AUTHOR("Ben Dooks "); +MODULE_LICENSE("GPL"); + +module_param_named(message, msg_enable, int, 0); +MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)"); +MODULE_ALIAS("spi:ks8851");