sleep 2
done
if [ ! -f $NFVBENCH_CONF ]; then
- exit 0
+ exit 0
fi
# Parse and obtain all configurations
done
tuna -c $(seq -s, 1 1 $WORKER_CORES) --isolate
+# Sometimes the interfaces on the loopback VM will use different drivers, e.g.
+# one from vswitch which is virtio based, one is from SRIOV VF. In this case,
+# we have to make sure the forwarder uses them in the right order, which is
+# especially important if the VM is in a PVVP chain.
+SWAP_FLAG=0
+if [ $INTF_MAC1 ] && [ $INTF_MAC2 ]; then
+ NET_PATH=/sys/class/net
+ EXP_INTF_1=$(for f in $(ls $NET_PATH/); do if grep -q "$INTF_MAC1" $NET_PATH/$f/address; then echo $f; break; fi; done)
+ EXP_PCI_ADDRESS_1=$(ethtool -i $EXP_INTF_1 | grep "bus-info" | awk -F' ' '{ print $2 }')
+ EXP_INTF_2=$(for f in $(ls $NET_PATH/); do if grep -q "$INTF_MAC2" $NET_PATH/$f/address; then echo $f; break; fi; done)
+ EXP_PCI_ADDRESS_2=$(ethtool -i $EXP_INTF_2 | grep "bus-info" | awk -F' ' '{ print $2 }')
+ if [ "$PCI_ADDRESS_1" == "$EXP_PCI_ADDRESS_2" ] && [ "$PCI_ADDRESS_2" == "$EXP_PCI_ADDRESS_1" ]; then
+ # Interfaces are not coming in the expected order:
+ # (1) Swap the traffic generator MAC in the case of testpmd;
+ # (2) Swap the interface configs in the case of VPP;
+ SWAP_FLAG=1
+ fi
+fi
+
# Configure the forwarder
+if [ -z "`lsmod | grep igb_uio`" ]; then
+ modprobe uio
+ insmod /dpdk/igb_uio.ko
+fi
if [ "$FORWARDER" == "testpmd" ]; then
echo "Configuring testpmd..."
- if [ -z "`lsmod | grep igb_uio`" ]; then
- modprobe uio
- insmod /dpdk/igb_uio.ko
+ if [ $SWAP_FLAG -eq 1 ]; then
+ TEMP=$TG_MAC1; TG_MAC1=$TG_MAC2; TG_MAC2=$TEMP
fi
# Binding ports to DPDK
/dpdk/dpdk-devbind.py -b igb_uio $PCI_ADDRESS_1
--burst=32 \
--txd=256 \
--rxd=1024 \
- --txqflags=0xf00 \
- --disable-hw-vlan \
--eth-peer=0,$TG_MAC1 \
--eth-peer=1,$TG_MAC2 \
--forward-mode=mac \
- --nb-cores=$WORKER_CORES\
- --max-pkt-len 9000
+ --nb-cores=$WORKER_CORES \
+ --max-pkt-len=9000 \
+ --cmdline-file=/dpdk/testpmd_cmd.txt
else
echo "Configuring vpp..."
cp /vpp/startup.conf /etc/vpp/startup.conf
cp /vpp/vm.conf /etc/vpp/vm.conf
-
+
sed -i "s/{{PCI_ADDRESS_1}}/$PCI_ADDRESS_1/g" /etc/vpp/startup.conf
sed -i "s/{{PCI_ADDRESS_2}}/$PCI_ADDRESS_2/g" /etc/vpp/startup.conf
sed -i "s/{{WORKER_CORES}}/$WORKER_CORES/g" /etc/vpp/startup.conf
service vpp start
+ sleep 10
INTFS=`vppctl show int | grep Ethernet | xargs`
INTF_1=`echo $INTFS | awk '{ print $1 }'`
INTF_2=`echo $INTFS | awk '{ print $4 }'`
+ if [ $SWAP_FLAG -eq 1 ]; then
+ TEMP=$INTF_1; INTF_1=$INTF_2; INTF_2=$TEMP
+ fi
sed -i "s/{{INTF_1}}/${INTF_1//\//\/}/g" /etc/vpp/vm.conf
sed -i "s/{{INTF_2}}/${INTF_2//\//\/}/g" /etc/vpp/vm.conf
sed -i "s/{{VNF_GATEWAY1_CIDR}}/${VNF_GATEWAY1_CIDR//\//\/}/g" /etc/vpp/vm.conf
sed -i "s/{{TG_NET2}}/${TG_NET2//\//\/}/g" /etc/vpp/vm.conf
sed -i "s/{{TG_GATEWAY1_IP}}/${TG_GATEWAY1_IP}/g" /etc/vpp/vm.conf
sed -i "s/{{TG_GATEWAY2_IP}}/${TG_GATEWAY2_IP}/g" /etc/vpp/vm.conf
-
service vpp restart
fi