--- /dev/null
+#ifndef __LIS3LV02D_H_
+#define __LIS3LV02D_H_
+
+/**
+ * struct lis3lv02d_platform_data - lis3 chip family platform data
+ * @click_flags: Click detection unit configuration
+ * @click_thresh_x: Click detection unit x axis threshold
+ * @click_thresh_y: Click detection unit y axis threshold
+ * @click_thresh_z: Click detection unit z axis threshold
+ * @click_time_limit: Click detection unit time parameter
+ * @click_latency: Click detection unit latency parameter
+ * @click_window: Click detection unit window parameter
+ * @irq_cfg: On chip irq source and type configuration (click /
+ * data available / wake up, open drain, polarity)
+ * @irq_flags1: Additional irq triggering flags for irq channel 0
+ * @irq_flags2: Additional irq triggering flags for irq channel 1
+ * @duration1: Wake up unit 1 duration parameter
+ * @duration2: Wake up unit 2 duration parameter
+ * @wakeup_flags: Wake up unit 1 flags
+ * @wakeup_thresh: Wake up unit 1 threshold value
+ * @wakeup_flags2: Wake up unit 2 flags
+ * @wakeup_thresh2: Wake up unit 2 threshold value
+ * @hipass_ctrl: High pass filter control (enable / disable, cut off
+ * frequency)
+ * @axis_x: Sensor orientation remapping for x-axis
+ * @axis_y: Sensor orientation remapping for y-axis
+ * @axis_z: Sensor orientation remapping for z-axis
+ * @driver_features: Enable bits for different features. Disabled by default
+ * @default_rate: Default sampling rate. 0 means reset default
+ * @setup_resources: Interrupt line setup call back function
+ * @release_resources: Interrupt line release call back function
+ * @st_min_limits[3]: Selftest acceptance minimum values
+ * @st_max_limits[3]: Selftest acceptance maximum values
+ * @irq2: Irq line 2 number
+ *
+ * Platform data is used to setup the sensor chip. Meaning of the different
+ * chip features can be found from the data sheet. It is publicly available
+ * at www.st.com web pages. Currently the platform data is used
+ * only for the 8 bit device. The 8 bit device has two wake up / free fall
+ * detection units and click detection unit. There are plenty of ways to
+ * configure the chip which makes is quite hard to explain deeper meaning of
+ * the fields here. Behaviour of the detection blocks varies heavily depending
+ * on the configuration. For example, interrupt detection block can use high
+ * pass filtered data which makes it react to the changes in the acceleration.
+ * Irq_flags can be used to enable interrupt detection on the both edges.
+ * With proper chip configuration this produces interrupt when some trigger
+ * starts and when it goes away.
+ */
+
+struct lis3lv02d_platform_data {
+ /* please note: the 'click' feature is only supported for
+ * LIS[32]02DL variants of the chip and will be ignored for
+ * others */
+#define LIS3_CLICK_SINGLE_X (1 << 0)
+#define LIS3_CLICK_DOUBLE_X (1 << 1)
+#define LIS3_CLICK_SINGLE_Y (1 << 2)
+#define LIS3_CLICK_DOUBLE_Y (1 << 3)
+#define LIS3_CLICK_SINGLE_Z (1 << 4)
+#define LIS3_CLICK_DOUBLE_Z (1 << 5)
+ unsigned char click_flags;
+ unsigned char click_thresh_x;
+ unsigned char click_thresh_y;
+ unsigned char click_thresh_z;
+ unsigned char click_time_limit;
+ unsigned char click_latency;
+ unsigned char click_window;
+
+#define LIS3_IRQ1_DISABLE (0 << 0)
+#define LIS3_IRQ1_FF_WU_1 (1 << 0)
+#define LIS3_IRQ1_FF_WU_2 (2 << 0)
+#define LIS3_IRQ1_FF_WU_12 (3 << 0)
+#define LIS3_IRQ1_DATA_READY (4 << 0)
+#define LIS3_IRQ1_CLICK (7 << 0)
+#define LIS3_IRQ1_MASK (7 << 0)
+#define LIS3_IRQ2_DISABLE (0 << 3)
+#define LIS3_IRQ2_FF_WU_1 (1 << 3)
+#define LIS3_IRQ2_FF_WU_2 (2 << 3)
+#define LIS3_IRQ2_FF_WU_12 (3 << 3)
+#define LIS3_IRQ2_DATA_READY (4 << 3)
+#define LIS3_IRQ2_CLICK (7 << 3)
+#define LIS3_IRQ2_MASK (7 << 3)
+#define LIS3_IRQ_OPEN_DRAIN (1 << 6)
+#define LIS3_IRQ_ACTIVE_LOW (1 << 7)
+ unsigned char irq_cfg;
+ unsigned char irq_flags1; /* Additional irq edge / level flags */
+ unsigned char irq_flags2; /* Additional irq edge / level flags */
+ unsigned char duration1;
+ unsigned char duration2;
+#define LIS3_WAKEUP_X_LO (1 << 0)
+#define LIS3_WAKEUP_X_HI (1 << 1)
+#define LIS3_WAKEUP_Y_LO (1 << 2)
+#define LIS3_WAKEUP_Y_HI (1 << 3)
+#define LIS3_WAKEUP_Z_LO (1 << 4)
+#define LIS3_WAKEUP_Z_HI (1 << 5)
+ unsigned char wakeup_flags;
+ unsigned char wakeup_thresh;
+ unsigned char wakeup_flags2;
+ unsigned char wakeup_thresh2;
+#define LIS3_HIPASS_CUTFF_8HZ 0
+#define LIS3_HIPASS_CUTFF_4HZ 1
+#define LIS3_HIPASS_CUTFF_2HZ 2
+#define LIS3_HIPASS_CUTFF_1HZ 3
+#define LIS3_HIPASS1_DISABLE (1 << 2)
+#define LIS3_HIPASS2_DISABLE (1 << 3)
+ unsigned char hipass_ctrl;
+#define LIS3_NO_MAP 0
+#define LIS3_DEV_X 1
+#define LIS3_DEV_Y 2
+#define LIS3_DEV_Z 3
+#define LIS3_INV_DEV_X -1
+#define LIS3_INV_DEV_Y -2
+#define LIS3_INV_DEV_Z -3
+ s8 axis_x;
+ s8 axis_y;
+ s8 axis_z;
+#define LIS3_USE_BLOCK_READ 0x02
+ u16 driver_features;
+ int default_rate;
+ int (*setup_resources)(void);
+ int (*release_resources)(void);
+ /* Limits for selftest are specified in chip data sheet */
+ s16 st_min_limits[3]; /* min pass limit x, y, z */
+ s16 st_max_limits[3]; /* max pass limit x, y, z */
+ int irq2;
+};
+
+#endif /* __LIS3LV02D_H_ */
Code Review / kvmfornfv.git / blobdiff