Add the rt linux 4.1.3-rt3 as base

[kvmfornfv.git] / kernel / include / linux / iio / gyro / itg3200.h

diff --git a/kernel/include/linux/iio/gyro/itg3200.h b/kernel/include/linux/iio/gyro/itg3200.h
new file mode 100644 (file)
index 0000000..2a82085
--- /dev/null
+++ b/kernel/include/linux/iio/gyro/itg3200.h
@@ -0,0 +1,154 @@
+/*
+ * itg3200.h -- support InvenSense ITG3200
+ *              Digital 3-Axis Gyroscope driver
+ *
+ * Copyright (c) 2011 Christian Strobel <christian.strobel@iis.fraunhofer.de>
+ * Copyright (c) 2011 Manuel Stahl <manuel.stahl@iis.fraunhofer.de>
+ * Copyright (c) 2012 Thorsten Nowak <thorsten.nowak@iis.fraunhofer.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef I2C_ITG3200_H_
+#define I2C_ITG3200_H_
+
+#include <linux/iio/iio.h>
+
+/* Register with I2C address (34h) */
+#define ITG3200_REG_ADDRESS            0x00
+
+/* Sample rate divider
+ * Range: 0 to 255
+ * Default value: 0x00 */
+#define ITG3200_REG_SAMPLE_RATE_DIV    0x15
+
+/* Digital low pass filter settings */
+#define ITG3200_REG_DLPF               0x16
+/* DLPF full scale range */
+#define ITG3200_DLPF_FS_SEL_2000       0x18
+/* Bandwidth (Hz) and internal sample rate
+ * (kHz) of DLPF */
+#define ITG3200_DLPF_256_8             0x00
+#define ITG3200_DLPF_188_1             0x01
+#define ITG3200_DLPF_98_1              0x02
+#define ITG3200_DLPF_42_1              0x03
+#define ITG3200_DLPF_20_1              0x04
+#define ITG3200_DLPF_10_1              0x05
+#define ITG3200_DLPF_5_1               0x06
+
+#define ITG3200_DLPF_CFG_MASK          0x07
+
+/* Configuration for interrupt operations */
+#define ITG3200_REG_IRQ_CONFIG         0x17
+/* Logic level */
+#define ITG3200_IRQ_ACTIVE_LOW         0x80
+#define ITG3200_IRQ_ACTIVE_HIGH                0x00
+/* Drive type */
+#define ITG3200_IRQ_OPEN_DRAIN         0x40
+#define ITG3200_IRQ_PUSH_PULL          0x00
+/* Latch mode */
+#define ITG3200_IRQ_LATCH_UNTIL_CLEARED        0x20
+#define ITG3200_IRQ_LATCH_50US_PULSE   0x00
+/* Latch clear method */
+#define ITG3200_IRQ_LATCH_CLEAR_ANY    0x10
+#define ITG3200_IRQ_LATCH_CLEAR_STATUS 0x00
+/* Enable interrupt when device is ready */
+#define ITG3200_IRQ_DEVICE_RDY_ENABLE  0x04
+/* Enable interrupt when data is available */
+#define ITG3200_IRQ_DATA_RDY_ENABLE    0x01
+
+/* Determine the status of ITG-3200 interrupts */
+#define ITG3200_REG_IRQ_STATUS         0x1A
+/* Status of 'device is ready'-interrupt */
+#define ITG3200_IRQ_DEVICE_RDY_STATUS  0x04
+/* Status of 'data is available'-interrupt */
+#define ITG3200_IRQ_DATA_RDY_STATUS    0x01
+
+/* Sensor registers */
+#define ITG3200_REG_TEMP_OUT_H         0x1B
+#define ITG3200_REG_TEMP_OUT_L         0x1C
+#define ITG3200_REG_GYRO_XOUT_H                0x1D
+#define ITG3200_REG_GYRO_XOUT_L                0x1E
+#define ITG3200_REG_GYRO_YOUT_H                0x1F
+#define ITG3200_REG_GYRO_YOUT_L                0x20
+#define ITG3200_REG_GYRO_ZOUT_H                0x21
+#define ITG3200_REG_GYRO_ZOUT_L                0x22
+
+/* Power management */
+#define ITG3200_REG_POWER_MANAGEMENT   0x3E
+/* Reset device and internal registers to the
+ * power-up-default settings */
+#define ITG3200_RESET                  0x80
+/* Enable low power sleep mode */
+#define ITG3200_SLEEP                  0x40
+/* Put according gyroscope in standby mode */
+#define ITG3200_STANDBY_GYRO_X         0x20
+#define ITG3200_STANDBY_GYRO_Y         0x10
+#define ITG3200_STANDBY_GYRO_Z         0x08
+/* Determine the device clock source */
+#define ITG3200_CLK_INTERNAL           0x00
+#define ITG3200_CLK_GYRO_X             0x01
+#define ITG3200_CLK_GYRO_Y             0x02
+#define ITG3200_CLK_GYRO_Z             0x03
+#define ITG3200_CLK_EXT_32K            0x04
+#define ITG3200_CLK_EXT_19M            0x05
+
+
+/**
+ * struct itg3200 - device instance specific data
+ * @i2c:    actual i2c_client
+ * @trig:   data ready trigger from itg3200 pin
+ **/
+struct itg3200 {
+       struct i2c_client       *i2c;
+       struct iio_trigger      *trig;
+};
+
+enum ITG3200_SCAN_INDEX {
+       ITG3200_SCAN_TEMP,
+       ITG3200_SCAN_GYRO_X,
+       ITG3200_SCAN_GYRO_Y,
+       ITG3200_SCAN_GYRO_Z,
+       ITG3200_SCAN_ELEMENTS,
+};
+
+int itg3200_write_reg_8(struct iio_dev *indio_dev,
+               u8 reg_address, u8 val);
+
+int itg3200_read_reg_8(struct iio_dev *indio_dev,
+               u8 reg_address, u8 *val);
+
+
+#ifdef CONFIG_IIO_BUFFER
+
+void itg3200_remove_trigger(struct iio_dev *indio_dev);
+int itg3200_probe_trigger(struct iio_dev *indio_dev);
+
+int itg3200_buffer_configure(struct iio_dev *indio_dev);
+void itg3200_buffer_unconfigure(struct iio_dev *indio_dev);
+
+#else /* CONFIG_IIO_BUFFER */
+
+static inline void itg3200_remove_trigger(struct iio_dev *indio_dev)
+{
+}
+
+static inline int itg3200_probe_trigger(struct iio_dev *indio_dev)
+{
+       return 0;
+}
+
+static inline int itg3200_buffer_configure(struct iio_dev *indio_dev)
+{
+       return 0;
+}
+
+static inline void itg3200_buffer_unconfigure(struct iio_dev *indio_dev)
+{
+}
+
+#endif  /* CONFIG_IIO_BUFFER */
+
+#endif /* ITG3200_H_ */