--- /dev/null
+/*
+ * AD9523 SPI Low Jitter Clock Generator
+ *
+ * Copyright 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ */
+
+#ifndef IIO_FREQUENCY_AD9523_H_
+#define IIO_FREQUENCY_AD9523_H_
+
+enum outp_drv_mode {
+ TRISTATE,
+ LVPECL_8mA,
+ LVDS_4mA,
+ LVDS_7mA,
+ HSTL0_16mA,
+ HSTL1_8mA,
+ CMOS_CONF1,
+ CMOS_CONF2,
+ CMOS_CONF3,
+ CMOS_CONF4,
+ CMOS_CONF5,
+ CMOS_CONF6,
+ CMOS_CONF7,
+ CMOS_CONF8,
+ CMOS_CONF9
+};
+
+enum ref_sel_mode {
+ NONEREVERTIVE_STAY_ON_REFB,
+ REVERT_TO_REFA,
+ SELECT_REFA,
+ SELECT_REFB,
+ EXT_REF_SEL
+};
+
+/**
+ * struct ad9523_channel_spec - Output channel configuration
+ *
+ * @channel_num: Output channel number.
+ * @divider_output_invert_en: Invert the polarity of the output clock.
+ * @sync_ignore_en: Ignore chip-level SYNC signal.
+ * @low_power_mode_en: Reduce power used in the differential output modes.
+ * @use_alt_clock_src: Channel divider uses alternative clk source.
+ * @output_dis: Disables, powers down the entire channel.
+ * @driver_mode: Output driver mode (logic level family).
+ * @divider_phase: Divider initial phase after a SYNC. Range 0..63
+ LSB = 1/2 of a period of the divider input clock.
+ * @channel_divider: 10-bit channel divider.
+ * @extended_name: Optional descriptive channel name.
+ */
+
+struct ad9523_channel_spec {
+ unsigned channel_num;
+ bool divider_output_invert_en;
+ bool sync_ignore_en;
+ bool low_power_mode_en;
+ /* CH0..CH3 VCXO, CH4..CH9 VCO2 */
+ bool use_alt_clock_src;
+ bool output_dis;
+ enum outp_drv_mode driver_mode;
+ unsigned char divider_phase;
+ unsigned short channel_divider;
+ char extended_name[16];
+};
+
+enum pll1_rzero_resistor {
+ RZERO_883_OHM,
+ RZERO_677_OHM,
+ RZERO_341_OHM,
+ RZERO_135_OHM,
+ RZERO_10_OHM,
+ RZERO_USE_EXT_RES = 8,
+};
+
+enum rpole2_resistor {
+ RPOLE2_900_OHM,
+ RPOLE2_450_OHM,
+ RPOLE2_300_OHM,
+ RPOLE2_225_OHM,
+};
+
+enum rzero_resistor {
+ RZERO_3250_OHM,
+ RZERO_2750_OHM,
+ RZERO_2250_OHM,
+ RZERO_2100_OHM,
+ RZERO_3000_OHM,
+ RZERO_2500_OHM,
+ RZERO_2000_OHM,
+ RZERO_1850_OHM,
+};
+
+enum cpole1_capacitor {
+ CPOLE1_0_PF,
+ CPOLE1_8_PF,
+ CPOLE1_16_PF,
+ CPOLE1_24_PF,
+ _CPOLE1_24_PF, /* place holder */
+ CPOLE1_32_PF,
+ CPOLE1_40_PF,
+ CPOLE1_48_PF,
+};
+
+/**
+ * struct ad9523_platform_data - platform specific information
+ *
+ * @vcxo_freq: External VCXO frequency in Hz
+ * @refa_diff_rcv_en: REFA differential/single-ended input selection.
+ * @refb_diff_rcv_en: REFB differential/single-ended input selection.
+ * @zd_in_diff_en: Zero Delay differential/single-ended input selection.
+ * @osc_in_diff_en: OSC differential/ single-ended input selection.
+ * @refa_cmos_neg_inp_en: REFA single-ended neg./pos. input enable.
+ * @refb_cmos_neg_inp_en: REFB single-ended neg./pos. input enable.
+ * @zd_in_cmos_neg_inp_en: Zero Delay single-ended neg./pos. input enable.
+ * @osc_in_cmos_neg_inp_en: OSC single-ended neg./pos. input enable.
+ * @refa_r_div: PLL1 10-bit REFA R divider.
+ * @refb_r_div: PLL1 10-bit REFB R divider.
+ * @pll1_feedback_div: PLL1 10-bit Feedback N divider.
+ * @pll1_charge_pump_current_nA: Magnitude of PLL1 charge pump current (nA).
+ * @zero_delay_mode_internal_en: Internal, external Zero Delay mode selection.
+ * @osc_in_feedback_en: PLL1 feedback path, local feedback from
+ * the OSC_IN receiver or zero delay mode
+ * @pll1_loop_filter_rzero: PLL1 Loop Filter Zero Resistor selection.
+ * @ref_mode: Reference selection mode.
+ * @pll2_charge_pump_current_nA: Magnitude of PLL2 charge pump current (nA).
+ * @pll2_ndiv_a_cnt: PLL2 Feedback N-divider, A Counter, range 0..4.
+ * @pll2_ndiv_b_cnt: PLL2 Feedback N-divider, B Counter, range 0..63.
+ * @pll2_freq_doubler_en: PLL2 frequency doubler enable.
+ * @pll2_r2_div: PLL2 R2 divider, range 0..31.
+ * @pll2_vco_diff_m1: VCO1 divider, range 3..5.
+ * @pll2_vco_diff_m2: VCO2 divider, range 3..5.
+ * @rpole2: PLL2 loop filter Rpole resistor value.
+ * @rzero: PLL2 loop filter Rzero resistor value.
+ * @cpole1: PLL2 loop filter Cpole capacitor value.
+ * @rzero_bypass_en: PLL2 loop filter Rzero bypass enable.
+ * @num_channels: Array size of struct ad9523_channel_spec.
+ * @channels: Pointer to channel array.
+ * @name: Optional alternative iio device name.
+ */
+
+struct ad9523_platform_data {
+ unsigned long vcxo_freq;
+
+ /* Differential/ Single-Ended Input Configuration */
+ bool refa_diff_rcv_en;
+ bool refb_diff_rcv_en;
+ bool zd_in_diff_en;
+ bool osc_in_diff_en;
+
+ /*
+ * Valid if differential input disabled
+ * if false defaults to pos input
+ */
+ bool refa_cmos_neg_inp_en;
+ bool refb_cmos_neg_inp_en;
+ bool zd_in_cmos_neg_inp_en;
+ bool osc_in_cmos_neg_inp_en;
+
+ /* PLL1 Setting */
+ unsigned short refa_r_div;
+ unsigned short refb_r_div;
+ unsigned short pll1_feedback_div;
+ unsigned short pll1_charge_pump_current_nA;
+ bool zero_delay_mode_internal_en;
+ bool osc_in_feedback_en;
+ enum pll1_rzero_resistor pll1_loop_filter_rzero;
+
+ /* Reference */
+ enum ref_sel_mode ref_mode;
+
+ /* PLL2 Setting */
+ unsigned int pll2_charge_pump_current_nA;
+ unsigned char pll2_ndiv_a_cnt;
+ unsigned char pll2_ndiv_b_cnt;
+ bool pll2_freq_doubler_en;
+ unsigned char pll2_r2_div;
+ unsigned char pll2_vco_diff_m1; /* 3..5 */
+ unsigned char pll2_vco_diff_m2; /* 3..5 */
+
+ /* Loop Filter PLL2 */
+ enum rpole2_resistor rpole2;
+ enum rzero_resistor rzero;
+ enum cpole1_capacitor cpole1;
+ bool rzero_bypass_en;
+
+ /* Output Channel Configuration */
+ int num_channels;
+ struct ad9523_channel_spec *channels;
+
+ char name[SPI_NAME_SIZE];
+};
+
+#endif /* IIO_FREQUENCY_AD9523_H_ */
Code Review / kvmfornfv.git / blobdiff