--- /dev/null
+/*
+ * twl4030.h - header for TWL4030 PM and audio CODEC device
+ *
+ * Copyright (C) 2005-2006 Texas Instruments, Inc.
+ *
+ * Based on tlv320aic23.c:
+ * Copyright (c) by Kai Svahn <kai.svahn@nokia.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __TWL_H_
+#define __TWL_H_
+
+#include <linux/types.h>
+#include <linux/input/matrix_keypad.h>
+
+/*
+ * Using the twl4030 core we address registers using a pair
+ * { module id, relative register offset }
+ * which that core then maps to the relevant
+ * { i2c slave, absolute register address }
+ *
+ * The module IDs are meaningful only to the twl4030 core code,
+ * which uses them as array indices to look up the first register
+ * address each module uses within a given i2c slave.
+ */
+
+/* Module IDs for similar functionalities found in twl4030/twl6030 */
+enum twl_module_ids {
+ TWL_MODULE_USB,
+ TWL_MODULE_PIH,
+ TWL_MODULE_MAIN_CHARGE,
+ TWL_MODULE_PM_MASTER,
+ TWL_MODULE_PM_RECEIVER,
+
+ TWL_MODULE_RTC,
+ TWL_MODULE_PWM,
+ TWL_MODULE_LED,
+ TWL_MODULE_SECURED_REG,
+
+ TWL_MODULE_LAST,
+};
+
+/* Modules only available in twl4030 series */
+enum twl4030_module_ids {
+ TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST,
+ TWL4030_MODULE_GPIO,
+ TWL4030_MODULE_INTBR,
+ TWL4030_MODULE_TEST,
+ TWL4030_MODULE_KEYPAD,
+
+ TWL4030_MODULE_MADC,
+ TWL4030_MODULE_INTERRUPTS,
+ TWL4030_MODULE_PRECHARGE,
+ TWL4030_MODULE_BACKUP,
+ TWL4030_MODULE_INT,
+
+ TWL5031_MODULE_ACCESSORY,
+ TWL5031_MODULE_INTERRUPTS,
+
+ TWL4030_MODULE_LAST,
+};
+
+/* Modules only available in twl6030 series */
+enum twl6030_module_ids {
+ TWL6030_MODULE_ID0 = TWL_MODULE_LAST,
+ TWL6030_MODULE_ID1,
+ TWL6030_MODULE_ID2,
+ TWL6030_MODULE_GPADC,
+ TWL6030_MODULE_GASGAUGE,
+
+ TWL6030_MODULE_LAST,
+};
+
+/* Until the clients has been converted to use TWL_MODULE_LED */
+#define TWL4030_MODULE_LED TWL_MODULE_LED
+
+#define GPIO_INTR_OFFSET 0
+#define KEYPAD_INTR_OFFSET 1
+#define BCI_INTR_OFFSET 2
+#define MADC_INTR_OFFSET 3
+#define USB_INTR_OFFSET 4
+#define CHARGERFAULT_INTR_OFFSET 5
+#define BCI_PRES_INTR_OFFSET 9
+#define USB_PRES_INTR_OFFSET 10
+#define RTC_INTR_OFFSET 11
+
+/*
+ * Offset from TWL6030_IRQ_BASE / pdata->irq_base
+ */
+#define PWR_INTR_OFFSET 0
+#define HOTDIE_INTR_OFFSET 12
+#define SMPSLDO_INTR_OFFSET 13
+#define BATDETECT_INTR_OFFSET 14
+#define SIMDETECT_INTR_OFFSET 15
+#define MMCDETECT_INTR_OFFSET 16
+#define GASGAUGE_INTR_OFFSET 17
+#define USBOTG_INTR_OFFSET 4
+#define CHARGER_INTR_OFFSET 2
+#define RSV_INTR_OFFSET 0
+
+/* INT register offsets */
+#define REG_INT_STS_A 0x00
+#define REG_INT_STS_B 0x01
+#define REG_INT_STS_C 0x02
+
+#define REG_INT_MSK_LINE_A 0x03
+#define REG_INT_MSK_LINE_B 0x04
+#define REG_INT_MSK_LINE_C 0x05
+
+#define REG_INT_MSK_STS_A 0x06
+#define REG_INT_MSK_STS_B 0x07
+#define REG_INT_MSK_STS_C 0x08
+
+/* MASK INT REG GROUP A */
+#define TWL6030_PWR_INT_MASK 0x07
+#define TWL6030_RTC_INT_MASK 0x18
+#define TWL6030_HOTDIE_INT_MASK 0x20
+#define TWL6030_SMPSLDOA_INT_MASK 0xC0
+
+/* MASK INT REG GROUP B */
+#define TWL6030_SMPSLDOB_INT_MASK 0x01
+#define TWL6030_BATDETECT_INT_MASK 0x02
+#define TWL6030_SIMDETECT_INT_MASK 0x04
+#define TWL6030_MMCDETECT_INT_MASK 0x08
+#define TWL6030_GPADC_INT_MASK 0x60
+#define TWL6030_GASGAUGE_INT_MASK 0x80
+
+/* MASK INT REG GROUP C */
+#define TWL6030_USBOTG_INT_MASK 0x0F
+#define TWL6030_CHARGER_CTRL_INT_MASK 0x10
+#define TWL6030_CHARGER_FAULT_INT_MASK 0x60
+
+#define TWL6030_MMCCTRL 0xEE
+#define VMMC_AUTO_OFF (0x1 << 3)
+#define SW_FC (0x1 << 2)
+#define STS_MMC 0x1
+
+#define TWL6030_CFG_INPUT_PUPD3 0xF2
+#define MMC_PU (0x1 << 3)
+#define MMC_PD (0x1 << 2)
+
+#define TWL_SIL_TYPE(rev) ((rev) & 0x00FFFFFF)
+#define TWL_SIL_REV(rev) ((rev) >> 24)
+#define TWL_SIL_5030 0x09002F
+#define TWL5030_REV_1_0 0x00
+#define TWL5030_REV_1_1 0x10
+#define TWL5030_REV_1_2 0x30
+
+#define TWL4030_CLASS_ID 0x4030
+#define TWL6030_CLASS_ID 0x6030
+unsigned int twl_rev(void);
+#define GET_TWL_REV (twl_rev())
+#define TWL_CLASS_IS(class, id) \
+static inline int twl_class_is_ ##class(void) \
+{ \
+ return ((id) == (GET_TWL_REV)) ? 1 : 0; \
+}
+
+TWL_CLASS_IS(4030, TWL4030_CLASS_ID)
+TWL_CLASS_IS(6030, TWL6030_CLASS_ID)
+
+/* Set the regcache bypass for the regmap associated with the nodule */
+int twl_set_regcache_bypass(u8 mod_no, bool enable);
+
+/*
+ * Read and write several 8-bit registers at once.
+ */
+int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes);
+
+/*
+ * Read and write single 8-bit registers
+ */
+static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) {
+ return twl_i2c_write(mod_no, &val, reg, 1);
+}
+
+static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) {
+ return twl_i2c_read(mod_no, val, reg, 1);
+}
+
+static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) {
+ val = cpu_to_le16(val);
+ return twl_i2c_write(mod_no, (u8*) &val, reg, 2);
+}
+
+static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) {
+ int ret;
+ ret = twl_i2c_read(mod_no, (u8*) val, reg, 2);
+ *val = le16_to_cpu(*val);
+ return ret;
+}
+
+int twl_get_type(void);
+int twl_get_version(void);
+int twl_get_hfclk_rate(void);
+
+int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
+int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
+
+/* Card detect Configuration for MMC1 Controller on OMAP4 */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect_config(void);
+#else
+static inline int twl6030_mmc_card_detect_config(void)
+{
+ pr_debug("twl6030_mmc_card_detect_config not supported\n");
+ return 0;
+}
+#endif
+
+/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
+#ifdef CONFIG_TWL4030_CORE
+int twl6030_mmc_card_detect(struct device *dev, int slot);
+#else
+static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
+{
+ pr_debug("Call back twl6030_mmc_card_detect not supported\n");
+ return -EIO;
+}
+#endif
+/*----------------------------------------------------------------------*/
+
+/*
+ * NOTE: at up to 1024 registers, this is a big chip.
+ *
+ * Avoid putting register declarations in this file, instead of into
+ * a driver-private file, unless some of the registers in a block
+ * need to be shared with other drivers. One example is blocks that
+ * have Secondary IRQ Handler (SIH) registers.
+ */
+
+#define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0)
+#define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1)
+#define TWL4030_SIH_CTRL_COR_MASK BIT(2)
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * GPIO Block Register offsets (use TWL4030_MODULE_GPIO)
+ */
+
+#define REG_GPIODATAIN1 0x0
+#define REG_GPIODATAIN2 0x1
+#define REG_GPIODATAIN3 0x2
+#define REG_GPIODATADIR1 0x3
+#define REG_GPIODATADIR2 0x4
+#define REG_GPIODATADIR3 0x5
+#define REG_GPIODATAOUT1 0x6
+#define REG_GPIODATAOUT2 0x7
+#define REG_GPIODATAOUT3 0x8
+#define REG_CLEARGPIODATAOUT1 0x9
+#define REG_CLEARGPIODATAOUT2 0xA
+#define REG_CLEARGPIODATAOUT3 0xB
+#define REG_SETGPIODATAOUT1 0xC
+#define REG_SETGPIODATAOUT2 0xD
+#define REG_SETGPIODATAOUT3 0xE
+#define REG_GPIO_DEBEN1 0xF
+#define REG_GPIO_DEBEN2 0x10
+#define REG_GPIO_DEBEN3 0x11
+#define REG_GPIO_CTRL 0x12
+#define REG_GPIOPUPDCTR1 0x13
+#define REG_GPIOPUPDCTR2 0x14
+#define REG_GPIOPUPDCTR3 0x15
+#define REG_GPIOPUPDCTR4 0x16
+#define REG_GPIOPUPDCTR5 0x17
+#define REG_GPIO_ISR1A 0x19
+#define REG_GPIO_ISR2A 0x1A
+#define REG_GPIO_ISR3A 0x1B
+#define REG_GPIO_IMR1A 0x1C
+#define REG_GPIO_IMR2A 0x1D
+#define REG_GPIO_IMR3A 0x1E
+#define REG_GPIO_ISR1B 0x1F
+#define REG_GPIO_ISR2B 0x20
+#define REG_GPIO_ISR3B 0x21
+#define REG_GPIO_IMR1B 0x22
+#define REG_GPIO_IMR2B 0x23
+#define REG_GPIO_IMR3B 0x24
+#define REG_GPIO_EDR1 0x28
+#define REG_GPIO_EDR2 0x29
+#define REG_GPIO_EDR3 0x2A
+#define REG_GPIO_EDR4 0x2B
+#define REG_GPIO_EDR5 0x2C
+#define REG_GPIO_SIH_CTRL 0x2D
+
+/* Up to 18 signals are available as GPIOs, when their
+ * pins are not assigned to another use (such as ULPI/USB).
+ */
+#define TWL4030_GPIO_MAX 18
+
+/*----------------------------------------------------------------------*/
+
+/*Interface Bit Register (INTBR) offsets
+ *(Use TWL_4030_MODULE_INTBR)
+ */
+
+#define REG_IDCODE_7_0 0x00
+#define REG_IDCODE_15_8 0x01
+#define REG_IDCODE_16_23 0x02
+#define REG_IDCODE_31_24 0x03
+#define REG_GPPUPDCTR1 0x0F
+#define REG_UNLOCK_TEST_REG 0x12
+
+/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */
+
+#define I2C_SCL_CTRL_PU BIT(0)
+#define I2C_SDA_CTRL_PU BIT(2)
+#define SR_I2C_SCL_CTRL_PU BIT(4)
+#define SR_I2C_SDA_CTRL_PU BIT(6)
+
+#define TWL_EEPROM_R_UNLOCK 0x49
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Keypad register offsets (use TWL4030_MODULE_KEYPAD)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_KEYPAD_KEYP_ISR1 0x11
+#define TWL4030_KEYPAD_KEYP_IMR1 0x12
+#define TWL4030_KEYPAD_KEYP_ISR2 0x13
+#define TWL4030_KEYPAD_KEYP_IMR2 0x14
+#define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */
+#define TWL4030_KEYPAD_KEYP_EDR 0x16
+#define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Multichannel ADC register offsets (use TWL4030_MODULE_MADC)
+ * ... SIH/interrupt only
+ */
+
+#define TWL4030_MADC_ISR1 0x61
+#define TWL4030_MADC_IMR1 0x62
+#define TWL4030_MADC_ISR2 0x63
+#define TWL4030_MADC_IMR2 0x64
+#define TWL4030_MADC_SIR 0x65 /* test register */
+#define TWL4030_MADC_EDR 0x66
+#define TWL4030_MADC_SIH_CTRL 0x67
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS)
+ */
+
+#define TWL4030_INTERRUPTS_BCIISR1A 0x0
+#define TWL4030_INTERRUPTS_BCIISR2A 0x1
+#define TWL4030_INTERRUPTS_BCIIMR1A 0x2
+#define TWL4030_INTERRUPTS_BCIIMR2A 0x3
+#define TWL4030_INTERRUPTS_BCIISR1B 0x4
+#define TWL4030_INTERRUPTS_BCIISR2B 0x5
+#define TWL4030_INTERRUPTS_BCIIMR1B 0x6
+#define TWL4030_INTERRUPTS_BCIIMR2B 0x7
+#define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */
+#define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */
+#define TWL4030_INTERRUPTS_BCIEDR1 0xa
+#define TWL4030_INTERRUPTS_BCIEDR2 0xb
+#define TWL4030_INTERRUPTS_BCIEDR3 0xc
+#define TWL4030_INTERRUPTS_BCISIHCTRL 0xd
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Power Interrupt block register offsets (use TWL4030_MODULE_INT)
+ */
+
+#define TWL4030_INT_PWR_ISR1 0x0
+#define TWL4030_INT_PWR_IMR1 0x1
+#define TWL4030_INT_PWR_ISR2 0x2
+#define TWL4030_INT_PWR_IMR2 0x3
+#define TWL4030_INT_PWR_SIR 0x4 /* test register */
+#define TWL4030_INT_PWR_EDR1 0x5
+#define TWL4030_INT_PWR_EDR2 0x6
+#define TWL4030_INT_PWR_SIH_CTRL 0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Accessory Interrupts
+ */
+#define TWL5031_ACIIMR_LSB 0x05
+#define TWL5031_ACIIMR_MSB 0x06
+#define TWL5031_ACIIDR_LSB 0x07
+#define TWL5031_ACIIDR_MSB 0x08
+#define TWL5031_ACCISR1 0x0F
+#define TWL5031_ACCIMR1 0x10
+#define TWL5031_ACCISR2 0x11
+#define TWL5031_ACCIMR2 0x12
+#define TWL5031_ACCSIR 0x13
+#define TWL5031_ACCEDR1 0x14
+#define TWL5031_ACCSIHCTRL 0x15
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * Battery Charger Controller
+ */
+
+#define TWL5031_INTERRUPTS_BCIISR1 0x0
+#define TWL5031_INTERRUPTS_BCIIMR1 0x1
+#define TWL5031_INTERRUPTS_BCIISR2 0x2
+#define TWL5031_INTERRUPTS_BCIIMR2 0x3
+#define TWL5031_INTERRUPTS_BCISIR 0x4
+#define TWL5031_INTERRUPTS_BCIEDR1 0x5
+#define TWL5031_INTERRUPTS_BCIEDR2 0x6
+#define TWL5031_INTERRUPTS_BCISIHCTRL 0x7
+
+/*----------------------------------------------------------------------*/
+
+/*
+ * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER)
+ */
+
+#define TWL4030_PM_MASTER_CFG_P1_TRANSITION 0x00
+#define TWL4030_PM_MASTER_CFG_P2_TRANSITION 0x01
+#define TWL4030_PM_MASTER_CFG_P3_TRANSITION 0x02
+#define TWL4030_PM_MASTER_CFG_P123_TRANSITION 0x03
+#define TWL4030_PM_MASTER_STS_BOOT 0x04
+#define TWL4030_PM_MASTER_CFG_BOOT 0x05
+#define TWL4030_PM_MASTER_SHUNDAN 0x06
+#define TWL4030_PM_MASTER_BOOT_BCI 0x07
+#define TWL4030_PM_MASTER_CFG_PWRANA1 0x08
+#define TWL4030_PM_MASTER_CFG_PWRANA2 0x09
+#define TWL4030_PM_MASTER_BACKUP_MISC_STS 0x0b
+#define TWL4030_PM_MASTER_BACKUP_MISC_CFG 0x0c
+#define TWL4030_PM_MASTER_BACKUP_MISC_TST 0x0d
+#define TWL4030_PM_MASTER_PROTECT_KEY 0x0e
+#define TWL4030_PM_MASTER_STS_HW_CONDITIONS 0x0f
+#define TWL4030_PM_MASTER_P1_SW_EVENTS 0x10
+#define TWL4030_PM_MASTER_P2_SW_EVENTS 0x11
+#define TWL4030_PM_MASTER_P3_SW_EVENTS 0x12
+#define TWL4030_PM_MASTER_STS_P123_STATE 0x13
+#define TWL4030_PM_MASTER_PB_CFG 0x14
+#define TWL4030_PM_MASTER_PB_WORD_MSB 0x15
+#define TWL4030_PM_MASTER_PB_WORD_LSB 0x16
+#define TWL4030_PM_MASTER_SEQ_ADD_W2P 0x1c
+#define TWL4030_PM_MASTER_SEQ_ADD_P2A 0x1d
+#define TWL4030_PM_MASTER_SEQ_ADD_A2W 0x1e
+#define TWL4030_PM_MASTER_SEQ_ADD_A2S 0x1f
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A12 0x20
+#define TWL4030_PM_MASTER_SEQ_ADD_S2A3 0x21
+#define TWL4030_PM_MASTER_SEQ_ADD_WARM 0x22
+#define TWL4030_PM_MASTER_MEMORY_ADDRESS 0x23
+#define TWL4030_PM_MASTER_MEMORY_DATA 0x24
+
+#define TWL4030_PM_MASTER_KEY_CFG1 0xc0
+#define TWL4030_PM_MASTER_KEY_CFG2 0x0c
+
+#define TWL4030_PM_MASTER_KEY_TST1 0xe0
+#define TWL4030_PM_MASTER_KEY_TST2 0x0e
+
+#define TWL4030_PM_MASTER_GLOBAL_TST 0xb6
+
+/*----------------------------------------------------------------------*/
+
+/* Power bus message definitions */
+
+/* The TWL4030/5030 splits its power-management resources (the various
+ * regulators, clock and reset lines) into 3 processor groups - P1, P2 and
+ * P3. These groups can then be configured to transition between sleep, wait-on
+ * and active states by sending messages to the power bus. See Section 5.4.2
+ * Power Resources of TWL4030 TRM
+ */
+
+/* Processor groups */
+#define DEV_GRP_NULL 0x0
+#define DEV_GRP_P1 0x1 /* P1: all OMAP devices */
+#define DEV_GRP_P2 0x2 /* P2: all Modem devices */
+#define DEV_GRP_P3 0x4 /* P3: all peripheral devices */
+
+/* Resource groups */
+#define RES_GRP_RES 0x0 /* Reserved */
+#define RES_GRP_PP 0x1 /* Power providers */
+#define RES_GRP_RC 0x2 /* Reset and control */
+#define RES_GRP_PP_RC 0x3
+#define RES_GRP_PR 0x4 /* Power references */
+#define RES_GRP_PP_PR 0x5
+#define RES_GRP_RC_PR 0x6
+#define RES_GRP_ALL 0x7 /* All resource groups */
+
+#define RES_TYPE2_R0 0x0
+#define RES_TYPE2_R1 0x1
+#define RES_TYPE2_R2 0x2
+
+#define RES_TYPE_R0 0x0
+#define RES_TYPE_ALL 0x7
+
+/* Resource states */
+#define RES_STATE_WRST 0xF
+#define RES_STATE_ACTIVE 0xE
+#define RES_STATE_SLEEP 0x8
+#define RES_STATE_OFF 0x0
+
+/* Power resources */
+
+/* Power providers */
+#define RES_VAUX1 1
+#define RES_VAUX2 2
+#define RES_VAUX3 3
+#define RES_VAUX4 4
+#define RES_VMMC1 5
+#define RES_VMMC2 6
+#define RES_VPLL1 7
+#define RES_VPLL2 8
+#define RES_VSIM 9
+#define RES_VDAC 10
+#define RES_VINTANA1 11
+#define RES_VINTANA2 12
+#define RES_VINTDIG 13
+#define RES_VIO 14
+#define RES_VDD1 15
+#define RES_VDD2 16
+#define RES_VUSB_1V5 17
+#define RES_VUSB_1V8 18
+#define RES_VUSB_3V1 19
+#define RES_VUSBCP 20
+#define RES_REGEN 21
+/* Reset and control */
+#define RES_NRES_PWRON 22
+#define RES_CLKEN 23
+#define RES_SYSEN 24
+#define RES_HFCLKOUT 25
+#define RES_32KCLKOUT 26
+#define RES_RESET 27
+/* Power Reference */
+#define RES_MAIN_REF 28
+
+#define TOTAL_RESOURCES 28
+/*
+ * Power Bus Message Format ... these can be sent individually by Linux,
+ * but are usually part of downloaded scripts that are run when various
+ * power events are triggered.
+ *
+ * Broadcast Message (16 Bits):
+ * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4]
+ * RES_STATE[3:0]
+ *
+ * Singular Message (16 Bits):
+ * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0]
+ */
+
+#define MSG_BROADCAST(devgrp, grp, type, type2, state) \
+ ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \
+ | (type) << 4 | (state))
+
+#define MSG_SINGULAR(devgrp, id, state) \
+ ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state))
+
+#define MSG_BROADCAST_ALL(devgrp, state) \
+ ((devgrp) << 5 | (state))
+
+#define MSG_BROADCAST_REF MSG_BROADCAST_ALL
+#define MSG_BROADCAST_PROV MSG_BROADCAST_ALL
+#define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL
+/*----------------------------------------------------------------------*/
+
+struct twl4030_clock_init_data {
+ bool ck32k_lowpwr_enable;
+};
+
+struct twl4030_bci_platform_data {
+ int *battery_tmp_tbl;
+ unsigned int tblsize;
+ int bb_uvolt; /* voltage to charge backup battery */
+ int bb_uamp; /* current for backup battery charging */
+};
+
+/* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */
+struct twl4030_gpio_platform_data {
+ /* package the two LED signals as output-only GPIOs? */
+ bool use_leds;
+
+ /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */
+ u8 mmc_cd;
+
+ /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */
+ u32 debounce;
+
+ /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup
+ * should be enabled. Else, if that bit is set in "pulldowns",
+ * that pulldown is enabled. Don't waste power by letting any
+ * digital inputs float...
+ */
+ u32 pullups;
+ u32 pulldowns;
+
+ int (*setup)(struct device *dev,
+ unsigned gpio, unsigned ngpio);
+ int (*teardown)(struct device *dev,
+ unsigned gpio, unsigned ngpio);
+};
+
+struct twl4030_madc_platform_data {
+ int irq_line;
+};
+
+/* Boards have unique mappings of {row, col} --> keycode.
+ * Column and row are 8 bits each, but range only from 0..7.
+ * a PERSISTENT_KEY is "always on" and never reported.
+ */
+#define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED)
+
+struct twl4030_keypad_data {
+ const struct matrix_keymap_data *keymap_data;
+ unsigned rows;
+ unsigned cols;
+ bool rep;
+};
+
+enum twl4030_usb_mode {
+ T2_USB_MODE_ULPI = 1,
+ T2_USB_MODE_CEA2011_3PIN = 2,
+};
+
+struct twl4030_usb_data {
+ enum twl4030_usb_mode usb_mode;
+ unsigned long features;
+
+ int (*phy_init)(struct device *dev);
+ int (*phy_exit)(struct device *dev);
+ /* Power on/off the PHY */
+ int (*phy_power)(struct device *dev, int iD, int on);
+ /* enable/disable phy clocks */
+ int (*phy_set_clock)(struct device *dev, int on);
+ /* suspend/resume of phy */
+ int (*phy_suspend)(struct device *dev, int suspend);
+};
+
+struct twl4030_ins {
+ u16 pmb_message;
+ u8 delay;
+};
+
+struct twl4030_script {
+ struct twl4030_ins *script;
+ unsigned size;
+ u8 flags;
+#define TWL4030_WRST_SCRIPT (1<<0)
+#define TWL4030_WAKEUP12_SCRIPT (1<<1)
+#define TWL4030_WAKEUP3_SCRIPT (1<<2)
+#define TWL4030_SLEEP_SCRIPT (1<<3)
+};
+
+struct twl4030_resconfig {
+ u8 resource;
+ u8 devgroup; /* Processor group that Power resource belongs to */
+ u8 type; /* Power resource addressed, 6 / broadcast message */
+ u8 type2; /* Power resource addressed, 3 / broadcast message */
+ u8 remap_off; /* off state remapping */
+ u8 remap_sleep; /* sleep state remapping */
+};
+
+struct twl4030_power_data {
+ struct twl4030_script **scripts;
+ unsigned num;
+ struct twl4030_resconfig *resource_config;
+ struct twl4030_resconfig *board_config;
+#define TWL4030_RESCONFIG_UNDEF ((u8)-1)
+ bool use_poweroff; /* Board is wired for TWL poweroff */
+};
+
+extern int twl4030_remove_script(u8 flags);
+extern void twl4030_power_off(void);
+
+struct twl4030_codec_data {
+ unsigned int digimic_delay; /* in ms */
+ unsigned int ramp_delay_value;
+ unsigned int offset_cncl_path;
+ unsigned int hs_extmute:1;
+ int hs_extmute_gpio;
+};
+
+struct twl4030_vibra_data {
+ unsigned int coexist;
+};
+
+struct twl4030_audio_data {
+ unsigned int audio_mclk;
+ struct twl4030_codec_data *codec;
+ struct twl4030_vibra_data *vibra;
+
+ /* twl6040 */
+ int audpwron_gpio; /* audio power-on gpio */
+ int naudint_irq; /* audio interrupt */
+ unsigned int irq_base;
+};
+
+struct twl4030_platform_data {
+ struct twl4030_clock_init_data *clock;
+ struct twl4030_bci_platform_data *bci;
+ struct twl4030_gpio_platform_data *gpio;
+ struct twl4030_madc_platform_data *madc;
+ struct twl4030_keypad_data *keypad;
+ struct twl4030_usb_data *usb;
+ struct twl4030_power_data *power;
+ struct twl4030_audio_data *audio;
+
+ /* Common LDO regulators for TWL4030/TWL6030 */
+ struct regulator_init_data *vdac;
+ struct regulator_init_data *vaux1;
+ struct regulator_init_data *vaux2;
+ struct regulator_init_data *vaux3;
+ struct regulator_init_data *vdd1;
+ struct regulator_init_data *vdd2;
+ struct regulator_init_data *vdd3;
+ /* TWL4030 LDO regulators */
+ struct regulator_init_data *vpll1;
+ struct regulator_init_data *vpll2;
+ struct regulator_init_data *vmmc1;
+ struct regulator_init_data *vmmc2;
+ struct regulator_init_data *vsim;
+ struct regulator_init_data *vaux4;
+ struct regulator_init_data *vio;
+ struct regulator_init_data *vintana1;
+ struct regulator_init_data *vintana2;
+ struct regulator_init_data *vintdig;
+ /* TWL6030 LDO regulators */
+ struct regulator_init_data *vmmc;
+ struct regulator_init_data *vpp;
+ struct regulator_init_data *vusim;
+ struct regulator_init_data *vana;
+ struct regulator_init_data *vcxio;
+ struct regulator_init_data *vusb;
+ struct regulator_init_data *clk32kg;
+ struct regulator_init_data *v1v8;
+ struct regulator_init_data *v2v1;
+ /* TWL6032 LDO regulators */
+ struct regulator_init_data *ldo1;
+ struct regulator_init_data *ldo2;
+ struct regulator_init_data *ldo3;
+ struct regulator_init_data *ldo4;
+ struct regulator_init_data *ldo5;
+ struct regulator_init_data *ldo6;
+ struct regulator_init_data *ldo7;
+ struct regulator_init_data *ldoln;
+ struct regulator_init_data *ldousb;
+ /* TWL6032 DCDC regulators */
+ struct regulator_init_data *smps3;
+ struct regulator_init_data *smps4;
+ struct regulator_init_data *vio6025;
+};
+
+struct twl_regulator_driver_data {
+ int (*set_voltage)(void *data, int target_uV);
+ int (*get_voltage)(void *data);
+ void *data;
+ unsigned long features;
+};
+/* chip-specific feature flags, for twl_regulator_driver_data.features */
+#define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */
+#define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */
+#define TWL5031 BIT(2) /* twl5031 has different registers */
+#define TWL6030_CLASS BIT(3) /* TWL6030 class */
+#define TWL6032_SUBCLASS BIT(4) /* TWL6032 has changed registers */
+#define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible
+ * but not officially supported.
+ * This flag is necessary to
+ * enable them.
+ */
+
+/*----------------------------------------------------------------------*/
+
+int twl4030_sih_setup(struct device *dev, int module, int irq_base);
+
+/* Offsets to Power Registers */
+#define TWL4030_VDAC_DEV_GRP 0x3B
+#define TWL4030_VDAC_DEDICATED 0x3E
+#define TWL4030_VAUX1_DEV_GRP 0x17
+#define TWL4030_VAUX1_DEDICATED 0x1A
+#define TWL4030_VAUX2_DEV_GRP 0x1B
+#define TWL4030_VAUX2_DEDICATED 0x1E
+#define TWL4030_VAUX3_DEV_GRP 0x1F
+#define TWL4030_VAUX3_DEDICATED 0x22
+
+static inline int twl4030charger_usb_en(int enable) { return 0; }
+
+/*----------------------------------------------------------------------*/
+
+/* Linux-specific regulator identifiers ... for now, we only support
+ * the LDOs, and leave the three buck converters alone. VDD1 and VDD2
+ * need to tie into hardware based voltage scaling (cpufreq etc), while
+ * VIO is generally fixed.
+ */
+
+/* TWL4030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck converters */
+#define TWL4030_REG_VDD1 0
+#define TWL4030_REG_VDD2 1
+#define TWL4030_REG_VIO 2
+
+/* EXTERNAL LDOs */
+#define TWL4030_REG_VDAC 3
+#define TWL4030_REG_VPLL1 4
+#define TWL4030_REG_VPLL2 5 /* not on all chips */
+#define TWL4030_REG_VMMC1 6
+#define TWL4030_REG_VMMC2 7 /* not on all chips */
+#define TWL4030_REG_VSIM 8 /* not on all chips */
+#define TWL4030_REG_VAUX1 9 /* not on all chips */
+#define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */
+#define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */
+#define TWL4030_REG_VAUX3 12 /* not on all chips */
+#define TWL4030_REG_VAUX4 13 /* not on all chips */
+
+/* INTERNAL LDOs */
+#define TWL4030_REG_VINTANA1 14
+#define TWL4030_REG_VINTANA2 15
+#define TWL4030_REG_VINTDIG 16
+#define TWL4030_REG_VUSB1V5 17
+#define TWL4030_REG_VUSB1V8 18
+#define TWL4030_REG_VUSB3V1 19
+
+/* TWL6030 SMPS/LDO's */
+/* EXTERNAL dc-to-dc buck convertor controllable via SR */
+#define TWL6030_REG_VDD1 30
+#define TWL6030_REG_VDD2 31
+#define TWL6030_REG_VDD3 32
+
+/* Non SR compliant dc-to-dc buck convertors */
+#define TWL6030_REG_VMEM 33
+#define TWL6030_REG_V2V1 34
+#define TWL6030_REG_V1V29 35
+#define TWL6030_REG_V1V8 36
+
+/* EXTERNAL LDOs */
+#define TWL6030_REG_VAUX1_6030 37
+#define TWL6030_REG_VAUX2_6030 38
+#define TWL6030_REG_VAUX3_6030 39
+#define TWL6030_REG_VMMC 40
+#define TWL6030_REG_VPP 41
+#define TWL6030_REG_VUSIM 42
+#define TWL6030_REG_VANA 43
+#define TWL6030_REG_VCXIO 44
+#define TWL6030_REG_VDAC 45
+#define TWL6030_REG_VUSB 46
+
+/* INTERNAL LDOs */
+#define TWL6030_REG_VRTC 47
+#define TWL6030_REG_CLK32KG 48
+
+/* LDOs on 6025 have different names */
+#define TWL6032_REG_LDO2 49
+#define TWL6032_REG_LDO4 50
+#define TWL6032_REG_LDO3 51
+#define TWL6032_REG_LDO5 52
+#define TWL6032_REG_LDO1 53
+#define TWL6032_REG_LDO7 54
+#define TWL6032_REG_LDO6 55
+#define TWL6032_REG_LDOLN 56
+#define TWL6032_REG_LDOUSB 57
+
+/* 6025 DCDC supplies */
+#define TWL6032_REG_SMPS3 58
+#define TWL6032_REG_SMPS4 59
+#define TWL6032_REG_VIO 60
+
+
+#endif /* End of __TWL4030_H */
Code Review / kvmfornfv.git / blobdiff