--- /dev/null
+/*
+ * Copyright © 2008 Keith Packard
+ *
+ * Permission to use, copy, modify, distribute, and sell this software and its
+ * documentation for any purpose is hereby granted without fee, provided that
+ * the above copyright notice appear in all copies and that both that copyright
+ * notice and this permission notice appear in supporting documentation, and
+ * that the name of the copyright holders not be used in advertising or
+ * publicity pertaining to distribution of the software without specific,
+ * written prior permission. The copyright holders make no representations
+ * about the suitability of this software for any purpose. It is provided "as
+ * is" without express or implied warranty.
+ *
+ * THE COPYRIGHT HOLDERS DISCLAIM ALL WARRANTIES WITH REGARD TO THIS SOFTWARE,
+ * INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, IN NO
+ * EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE FOR ANY SPECIAL, INDIRECT OR
+ * CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE,
+ * DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER
+ * TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
+ * OF THIS SOFTWARE.
+ */
+
+#ifndef _DRM_DP_HELPER_H_
+#define _DRM_DP_HELPER_H_
+
+#include <linux/types.h>
+#include <linux/i2c.h>
+#include <linux/delay.h>
+
+/*
+ * Unless otherwise noted, all values are from the DP 1.1a spec. Note that
+ * DP and DPCD versions are independent. Differences from 1.0 are not noted,
+ * 1.0 devices basically don't exist in the wild.
+ *
+ * Abbreviations, in chronological order:
+ *
+ * eDP: Embedded DisplayPort version 1
+ * DPI: DisplayPort Interoperability Guideline v1.1a
+ * 1.2: DisplayPort 1.2
+ * MST: Multistream Transport - part of DP 1.2a
+ *
+ * 1.2 formally includes both eDP and DPI definitions.
+ */
+
+#define DP_AUX_MAX_PAYLOAD_BYTES 16
+
+#define DP_AUX_I2C_WRITE 0x0
+#define DP_AUX_I2C_READ 0x1
+#define DP_AUX_I2C_STATUS 0x2
+#define DP_AUX_I2C_MOT 0x4
+#define DP_AUX_NATIVE_WRITE 0x8
+#define DP_AUX_NATIVE_READ 0x9
+
+#define DP_AUX_NATIVE_REPLY_ACK (0x0 << 0)
+#define DP_AUX_NATIVE_REPLY_NACK (0x1 << 0)
+#define DP_AUX_NATIVE_REPLY_DEFER (0x2 << 0)
+#define DP_AUX_NATIVE_REPLY_MASK (0x3 << 0)
+
+#define DP_AUX_I2C_REPLY_ACK (0x0 << 2)
+#define DP_AUX_I2C_REPLY_NACK (0x1 << 2)
+#define DP_AUX_I2C_REPLY_DEFER (0x2 << 2)
+#define DP_AUX_I2C_REPLY_MASK (0x3 << 2)
+
+/* AUX CH addresses */
+/* DPCD */
+#define DP_DPCD_REV 0x000
+
+#define DP_MAX_LINK_RATE 0x001
+
+#define DP_MAX_LANE_COUNT 0x002
+# define DP_MAX_LANE_COUNT_MASK 0x1f
+# define DP_TPS3_SUPPORTED (1 << 6) /* 1.2 */
+# define DP_ENHANCED_FRAME_CAP (1 << 7)
+
+#define DP_MAX_DOWNSPREAD 0x003
+# define DP_NO_AUX_HANDSHAKE_LINK_TRAINING (1 << 6)
+
+#define DP_NORP 0x004
+
+#define DP_DOWNSTREAMPORT_PRESENT 0x005
+# define DP_DWN_STRM_PORT_PRESENT (1 << 0)
+# define DP_DWN_STRM_PORT_TYPE_MASK 0x06
+# define DP_DWN_STRM_PORT_TYPE_DP (0 << 1)
+# define DP_DWN_STRM_PORT_TYPE_ANALOG (1 << 1)
+# define DP_DWN_STRM_PORT_TYPE_TMDS (2 << 1)
+# define DP_DWN_STRM_PORT_TYPE_OTHER (3 << 1)
+# define DP_FORMAT_CONVERSION (1 << 3)
+# define DP_DETAILED_CAP_INFO_AVAILABLE (1 << 4) /* DPI */
+
+#define DP_MAIN_LINK_CHANNEL_CODING 0x006
+
+#define DP_DOWN_STREAM_PORT_COUNT 0x007
+# define DP_PORT_COUNT_MASK 0x0f
+# define DP_MSA_TIMING_PAR_IGNORED (1 << 6) /* eDP */
+# define DP_OUI_SUPPORT (1 << 7)
+
+#define DP_RECEIVE_PORT_0_CAP_0 0x008
+# define DP_LOCAL_EDID_PRESENT (1 << 1)
+# define DP_ASSOCIATED_TO_PRECEDING_PORT (1 << 2)
+
+#define DP_RECEIVE_PORT_0_BUFFER_SIZE 0x009
+
+#define DP_RECEIVE_PORT_1_CAP_0 0x00a
+#define DP_RECEIVE_PORT_1_BUFFER_SIZE 0x00b
+
+#define DP_I2C_SPEED_CAP 0x00c /* DPI */
+# define DP_I2C_SPEED_1K 0x01
+# define DP_I2C_SPEED_5K 0x02
+# define DP_I2C_SPEED_10K 0x04
+# define DP_I2C_SPEED_100K 0x08
+# define DP_I2C_SPEED_400K 0x10
+# define DP_I2C_SPEED_1M 0x20
+
+#define DP_EDP_CONFIGURATION_CAP 0x00d /* XXX 1.2? */
+# define DP_ALTERNATE_SCRAMBLER_RESET_CAP (1 << 0)
+# define DP_FRAMING_CHANGE_CAP (1 << 1)
+# define DP_DPCD_DISPLAY_CONTROL_CAPABLE (1 << 3) /* edp v1.2 or higher */
+
+#define DP_TRAINING_AUX_RD_INTERVAL 0x00e /* XXX 1.2? */
+
+#define DP_ADAPTER_CAP 0x00f /* 1.2 */
+# define DP_FORCE_LOAD_SENSE_CAP (1 << 0)
+# define DP_ALTERNATE_I2C_PATTERN_CAP (1 << 1)
+
+#define DP_SUPPORTED_LINK_RATES 0x010 /* eDP 1.4 */
+# define DP_MAX_SUPPORTED_RATES 8 /* 16-bit little-endian */
+
+/* Multiple stream transport */
+#define DP_FAUX_CAP 0x020 /* 1.2 */
+# define DP_FAUX_CAP_1 (1 << 0)
+
+#define DP_MSTM_CAP 0x021 /* 1.2 */
+# define DP_MST_CAP (1 << 0)
+
+#define DP_NUMBER_OF_AUDIO_ENDPOINTS 0x022 /* 1.2 */
+
+/* AV_SYNC_DATA_BLOCK 1.2 */
+#define DP_AV_GRANULARITY 0x023
+# define DP_AG_FACTOR_MASK (0xf << 0)
+# define DP_AG_FACTOR_3MS (0 << 0)
+# define DP_AG_FACTOR_2MS (1 << 0)
+# define DP_AG_FACTOR_1MS (2 << 0)
+# define DP_AG_FACTOR_500US (3 << 0)
+# define DP_AG_FACTOR_200US (4 << 0)
+# define DP_AG_FACTOR_100US (5 << 0)
+# define DP_AG_FACTOR_10US (6 << 0)
+# define DP_AG_FACTOR_1US (7 << 0)
+# define DP_VG_FACTOR_MASK (0xf << 4)
+# define DP_VG_FACTOR_3MS (0 << 4)
+# define DP_VG_FACTOR_2MS (1 << 4)
+# define DP_VG_FACTOR_1MS (2 << 4)
+# define DP_VG_FACTOR_500US (3 << 4)
+# define DP_VG_FACTOR_200US (4 << 4)
+# define DP_VG_FACTOR_100US (5 << 4)
+
+#define DP_AUD_DEC_LAT0 0x024
+#define DP_AUD_DEC_LAT1 0x025
+
+#define DP_AUD_PP_LAT0 0x026
+#define DP_AUD_PP_LAT1 0x027
+
+#define DP_VID_INTER_LAT 0x028
+
+#define DP_VID_PROG_LAT 0x029
+
+#define DP_REP_LAT 0x02a
+
+#define DP_AUD_DEL_INS0 0x02b
+#define DP_AUD_DEL_INS1 0x02c
+#define DP_AUD_DEL_INS2 0x02d
+/* End of AV_SYNC_DATA_BLOCK */
+
+#define DP_RECEIVER_ALPM_CAP 0x02e /* eDP 1.4 */
+# define DP_ALPM_CAP (1 << 0)
+
+#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CAP 0x02f /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_CAP (1 << 0)
+
+#define DP_GUID 0x030 /* 1.2 */
+
+#define DP_PSR_SUPPORT 0x070 /* XXX 1.2? */
+# define DP_PSR_IS_SUPPORTED 1
+# define DP_PSR2_IS_SUPPORTED 2 /* eDP 1.4 */
+
+#define DP_PSR_CAPS 0x071 /* XXX 1.2? */
+# define DP_PSR_NO_TRAIN_ON_EXIT 1
+# define DP_PSR_SETUP_TIME_330 (0 << 1)
+# define DP_PSR_SETUP_TIME_275 (1 << 1)
+# define DP_PSR_SETUP_TIME_220 (2 << 1)
+# define DP_PSR_SETUP_TIME_165 (3 << 1)
+# define DP_PSR_SETUP_TIME_110 (4 << 1)
+# define DP_PSR_SETUP_TIME_55 (5 << 1)
+# define DP_PSR_SETUP_TIME_0 (6 << 1)
+# define DP_PSR_SETUP_TIME_MASK (7 << 1)
+# define DP_PSR_SETUP_TIME_SHIFT 1
+
+/*
+ * 0x80-0x8f describe downstream port capabilities, but there are two layouts
+ * based on whether DP_DETAILED_CAP_INFO_AVAILABLE was set. If it was not,
+ * each port's descriptor is one byte wide. If it was set, each port's is
+ * four bytes wide, starting with the one byte from the base info. As of
+ * DP interop v1.1a only VGA defines additional detail.
+ */
+
+/* offset 0 */
+#define DP_DOWNSTREAM_PORT_0 0x80
+# define DP_DS_PORT_TYPE_MASK (7 << 0)
+# define DP_DS_PORT_TYPE_DP 0
+# define DP_DS_PORT_TYPE_VGA 1
+# define DP_DS_PORT_TYPE_DVI 2
+# define DP_DS_PORT_TYPE_HDMI 3
+# define DP_DS_PORT_TYPE_NON_EDID 4
+# define DP_DS_PORT_HPD (1 << 3)
+/* offset 1 for VGA is maximum megapixels per second / 8 */
+/* offset 2 */
+# define DP_DS_VGA_MAX_BPC_MASK (3 << 0)
+# define DP_DS_VGA_8BPC 0
+# define DP_DS_VGA_10BPC 1
+# define DP_DS_VGA_12BPC 2
+# define DP_DS_VGA_16BPC 3
+
+/* link configuration */
+#define DP_LINK_BW_SET 0x100
+# define DP_LINK_RATE_TABLE 0x00 /* eDP 1.4 */
+# define DP_LINK_BW_1_62 0x06
+# define DP_LINK_BW_2_7 0x0a
+# define DP_LINK_BW_5_4 0x14 /* 1.2 */
+
+#define DP_LANE_COUNT_SET 0x101
+# define DP_LANE_COUNT_MASK 0x0f
+# define DP_LANE_COUNT_ENHANCED_FRAME_EN (1 << 7)
+
+#define DP_TRAINING_PATTERN_SET 0x102
+# define DP_TRAINING_PATTERN_DISABLE 0
+# define DP_TRAINING_PATTERN_1 1
+# define DP_TRAINING_PATTERN_2 2
+# define DP_TRAINING_PATTERN_3 3 /* 1.2 */
+# define DP_TRAINING_PATTERN_MASK 0x3
+
+/* DPCD 1.1 only. For DPCD >= 1.2 see per-lane DP_LINK_QUAL_LANEn_SET */
+# define DP_LINK_QUAL_PATTERN_11_DISABLE (0 << 2)
+# define DP_LINK_QUAL_PATTERN_11_D10_2 (1 << 2)
+# define DP_LINK_QUAL_PATTERN_11_ERROR_RATE (2 << 2)
+# define DP_LINK_QUAL_PATTERN_11_PRBS7 (3 << 2)
+# define DP_LINK_QUAL_PATTERN_11_MASK (3 << 2)
+
+# define DP_RECOVERED_CLOCK_OUT_EN (1 << 4)
+# define DP_LINK_SCRAMBLING_DISABLE (1 << 5)
+
+# define DP_SYMBOL_ERROR_COUNT_BOTH (0 << 6)
+# define DP_SYMBOL_ERROR_COUNT_DISPARITY (1 << 6)
+# define DP_SYMBOL_ERROR_COUNT_SYMBOL (2 << 6)
+# define DP_SYMBOL_ERROR_COUNT_MASK (3 << 6)
+
+#define DP_TRAINING_LANE0_SET 0x103
+#define DP_TRAINING_LANE1_SET 0x104
+#define DP_TRAINING_LANE2_SET 0x105
+#define DP_TRAINING_LANE3_SET 0x106
+
+# define DP_TRAIN_VOLTAGE_SWING_MASK 0x3
+# define DP_TRAIN_VOLTAGE_SWING_SHIFT 0
+# define DP_TRAIN_MAX_SWING_REACHED (1 << 2)
+# define DP_TRAIN_VOLTAGE_SWING_LEVEL_0 (0 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_LEVEL_1 (1 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_LEVEL_2 (2 << 0)
+# define DP_TRAIN_VOLTAGE_SWING_LEVEL_3 (3 << 0)
+
+# define DP_TRAIN_PRE_EMPHASIS_MASK (3 << 3)
+# define DP_TRAIN_PRE_EMPH_LEVEL_0 (0 << 3)
+# define DP_TRAIN_PRE_EMPH_LEVEL_1 (1 << 3)
+# define DP_TRAIN_PRE_EMPH_LEVEL_2 (2 << 3)
+# define DP_TRAIN_PRE_EMPH_LEVEL_3 (3 << 3)
+
+# define DP_TRAIN_PRE_EMPHASIS_SHIFT 3
+# define DP_TRAIN_MAX_PRE_EMPHASIS_REACHED (1 << 5)
+
+#define DP_DOWNSPREAD_CTRL 0x107
+# define DP_SPREAD_AMP_0_5 (1 << 4)
+# define DP_MSA_TIMING_PAR_IGNORE_EN (1 << 7) /* eDP */
+
+#define DP_MAIN_LINK_CHANNEL_CODING_SET 0x108
+# define DP_SET_ANSI_8B10B (1 << 0)
+
+#define DP_I2C_SPEED_CONTROL_STATUS 0x109 /* DPI */
+/* bitmask as for DP_I2C_SPEED_CAP */
+
+#define DP_EDP_CONFIGURATION_SET 0x10a /* XXX 1.2? */
+# define DP_ALTERNATE_SCRAMBLER_RESET_ENABLE (1 << 0)
+# define DP_FRAMING_CHANGE_ENABLE (1 << 1)
+# define DP_PANEL_SELF_TEST_ENABLE (1 << 7)
+
+#define DP_LINK_QUAL_LANE0_SET 0x10b /* DPCD >= 1.2 */
+#define DP_LINK_QUAL_LANE1_SET 0x10c
+#define DP_LINK_QUAL_LANE2_SET 0x10d
+#define DP_LINK_QUAL_LANE3_SET 0x10e
+# define DP_LINK_QUAL_PATTERN_DISABLE 0
+# define DP_LINK_QUAL_PATTERN_D10_2 1
+# define DP_LINK_QUAL_PATTERN_ERROR_RATE 2
+# define DP_LINK_QUAL_PATTERN_PRBS7 3
+# define DP_LINK_QUAL_PATTERN_80BIT_CUSTOM 4
+# define DP_LINK_QUAL_PATTERN_HBR2_EYE 5
+# define DP_LINK_QUAL_PATTERN_MASK 7
+
+#define DP_TRAINING_LANE0_1_SET2 0x10f
+#define DP_TRAINING_LANE2_3_SET2 0x110
+# define DP_LANE02_POST_CURSOR2_SET_MASK (3 << 0)
+# define DP_LANE02_MAX_POST_CURSOR2_REACHED (1 << 2)
+# define DP_LANE13_POST_CURSOR2_SET_MASK (3 << 4)
+# define DP_LANE13_MAX_POST_CURSOR2_REACHED (1 << 6)
+
+#define DP_MSTM_CTRL 0x111 /* 1.2 */
+# define DP_MST_EN (1 << 0)
+# define DP_UP_REQ_EN (1 << 1)
+# define DP_UPSTREAM_IS_SRC (1 << 2)
+
+#define DP_AUDIO_DELAY0 0x112 /* 1.2 */
+#define DP_AUDIO_DELAY1 0x113
+#define DP_AUDIO_DELAY2 0x114
+
+#define DP_LINK_RATE_SET 0x115 /* eDP 1.4 */
+# define DP_LINK_RATE_SET_SHIFT 0
+# define DP_LINK_RATE_SET_MASK (7 << 0)
+
+#define DP_RECEIVER_ALPM_CONFIG 0x116 /* eDP 1.4 */
+# define DP_ALPM_ENABLE (1 << 0)
+# define DP_ALPM_LOCK_ERROR_IRQ_HPD_ENABLE (1 << 1)
+
+#define DP_SINK_DEVICE_AUX_FRAME_SYNC_CONF 0x117 /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_ENABLE (1 << 0)
+# define DP_IRQ_HPD_ENABLE (1 << 1)
+
+#define DP_UPSTREAM_DEVICE_DP_PWR_NEED 0x118 /* 1.2 */
+# define DP_PWR_NOT_NEEDED (1 << 0)
+
+#define DP_AUX_FRAME_SYNC_VALUE 0x15c /* eDP 1.4 */
+# define DP_AUX_FRAME_SYNC_VALID (1 << 0)
+
+#define DP_PSR_EN_CFG 0x170 /* XXX 1.2? */
+# define DP_PSR_ENABLE (1 << 0)
+# define DP_PSR_MAIN_LINK_ACTIVE (1 << 1)
+# define DP_PSR_CRC_VERIFICATION (1 << 2)
+# define DP_PSR_FRAME_CAPTURE (1 << 3)
+# define DP_PSR_SELECTIVE_UPDATE (1 << 4)
+# define DP_PSR_IRQ_HPD_WITH_CRC_ERRORS (1 << 5)
+
+#define DP_ADAPTER_CTRL 0x1a0
+# define DP_ADAPTER_CTRL_FORCE_LOAD_SENSE (1 << 0)
+
+#define DP_BRANCH_DEVICE_CTRL 0x1a1
+# define DP_BRANCH_DEVICE_IRQ_HPD (1 << 0)
+
+#define DP_PAYLOAD_ALLOCATE_SET 0x1c0
+#define DP_PAYLOAD_ALLOCATE_START_TIME_SLOT 0x1c1
+#define DP_PAYLOAD_ALLOCATE_TIME_SLOT_COUNT 0x1c2
+
+#define DP_SINK_COUNT 0x200
+/* prior to 1.2 bit 7 was reserved mbz */
+# define DP_GET_SINK_COUNT(x) ((((x) & 0x80) >> 1) | ((x) & 0x3f))
+# define DP_SINK_CP_READY (1 << 6)
+
+#define DP_DEVICE_SERVICE_IRQ_VECTOR 0x201
+# define DP_REMOTE_CONTROL_COMMAND_PENDING (1 << 0)
+# define DP_AUTOMATED_TEST_REQUEST (1 << 1)
+# define DP_CP_IRQ (1 << 2)
+# define DP_MCCS_IRQ (1 << 3)
+# define DP_DOWN_REP_MSG_RDY (1 << 4) /* 1.2 MST */
+# define DP_UP_REQ_MSG_RDY (1 << 5) /* 1.2 MST */
+# define DP_SINK_SPECIFIC_IRQ (1 << 6)
+
+#define DP_LANE0_1_STATUS 0x202
+#define DP_LANE2_3_STATUS 0x203
+# define DP_LANE_CR_DONE (1 << 0)
+# define DP_LANE_CHANNEL_EQ_DONE (1 << 1)
+# define DP_LANE_SYMBOL_LOCKED (1 << 2)
+
+#define DP_CHANNEL_EQ_BITS (DP_LANE_CR_DONE | \
+ DP_LANE_CHANNEL_EQ_DONE | \
+ DP_LANE_SYMBOL_LOCKED)
+
+#define DP_LANE_ALIGN_STATUS_UPDATED 0x204
+
+#define DP_INTERLANE_ALIGN_DONE (1 << 0)
+#define DP_DOWNSTREAM_PORT_STATUS_CHANGED (1 << 6)
+#define DP_LINK_STATUS_UPDATED (1 << 7)
+
+#define DP_SINK_STATUS 0x205
+
+#define DP_RECEIVE_PORT_0_STATUS (1 << 0)
+#define DP_RECEIVE_PORT_1_STATUS (1 << 1)
+
+#define DP_ADJUST_REQUEST_LANE0_1 0x206
+#define DP_ADJUST_REQUEST_LANE2_3 0x207
+# define DP_ADJUST_VOLTAGE_SWING_LANE0_MASK 0x03
+# define DP_ADJUST_VOLTAGE_SWING_LANE0_SHIFT 0
+# define DP_ADJUST_PRE_EMPHASIS_LANE0_MASK 0x0c
+# define DP_ADJUST_PRE_EMPHASIS_LANE0_SHIFT 2
+# define DP_ADJUST_VOLTAGE_SWING_LANE1_MASK 0x30
+# define DP_ADJUST_VOLTAGE_SWING_LANE1_SHIFT 4
+# define DP_ADJUST_PRE_EMPHASIS_LANE1_MASK 0xc0
+# define DP_ADJUST_PRE_EMPHASIS_LANE1_SHIFT 6
+
+#define DP_TEST_REQUEST 0x218
+# define DP_TEST_LINK_TRAINING (1 << 0)
+# define DP_TEST_LINK_VIDEO_PATTERN (1 << 1)
+# define DP_TEST_LINK_EDID_READ (1 << 2)
+# define DP_TEST_LINK_PHY_TEST_PATTERN (1 << 3) /* DPCD >= 1.1 */
+# define DP_TEST_LINK_FAUX_PATTERN (1 << 4) /* DPCD >= 1.2 */
+
+#define DP_TEST_LINK_RATE 0x219
+# define DP_LINK_RATE_162 (0x6)
+# define DP_LINK_RATE_27 (0xa)
+
+#define DP_TEST_LANE_COUNT 0x220
+
+#define DP_TEST_PATTERN 0x221
+
+#define DP_TEST_CRC_R_CR 0x240
+#define DP_TEST_CRC_G_Y 0x242
+#define DP_TEST_CRC_B_CB 0x244
+
+#define DP_TEST_SINK_MISC 0x246
+# define DP_TEST_CRC_SUPPORTED (1 << 5)
+# define DP_TEST_COUNT_MASK 0x7
+
+#define DP_TEST_RESPONSE 0x260
+# define DP_TEST_ACK (1 << 0)
+# define DP_TEST_NAK (1 << 1)
+# define DP_TEST_EDID_CHECKSUM_WRITE (1 << 2)
+
+#define DP_TEST_EDID_CHECKSUM 0x261
+
+#define DP_TEST_SINK 0x270
+# define DP_TEST_SINK_START (1 << 0)
+
+#define DP_PAYLOAD_TABLE_UPDATE_STATUS 0x2c0 /* 1.2 MST */
+# define DP_PAYLOAD_TABLE_UPDATED (1 << 0)
+# define DP_PAYLOAD_ACT_HANDLED (1 << 1)
+
+#define DP_VC_PAYLOAD_ID_SLOT_1 0x2c1 /* 1.2 MST */
+/* up to ID_SLOT_63 at 0x2ff */
+
+#define DP_SOURCE_OUI 0x300
+#define DP_SINK_OUI 0x400
+#define DP_BRANCH_OUI 0x500
+
+#define DP_SET_POWER 0x600
+# define DP_SET_POWER_D0 0x1
+# define DP_SET_POWER_D3 0x2
+# define DP_SET_POWER_MASK 0x3
+
+#define DP_EDP_DPCD_REV 0x700 /* eDP 1.2 */
+# define DP_EDP_11 0x00
+# define DP_EDP_12 0x01
+# define DP_EDP_13 0x02
+# define DP_EDP_14 0x03
+
+#define DP_EDP_GENERAL_CAP_1 0x701
+
+#define DP_EDP_BACKLIGHT_ADJUSTMENT_CAP 0x702
+
+#define DP_EDP_GENERAL_CAP_2 0x703
+
+#define DP_EDP_GENERAL_CAP_3 0x704 /* eDP 1.4 */
+
+#define DP_EDP_DISPLAY_CONTROL_REGISTER 0x720
+
+#define DP_EDP_BACKLIGHT_MODE_SET_REGISTER 0x721
+
+#define DP_EDP_BACKLIGHT_BRIGHTNESS_MSB 0x722
+#define DP_EDP_BACKLIGHT_BRIGHTNESS_LSB 0x723
+
+#define DP_EDP_PWMGEN_BIT_COUNT 0x724
+#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN 0x725
+#define DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX 0x726
+
+#define DP_EDP_BACKLIGHT_CONTROL_STATUS 0x727
+
+#define DP_EDP_BACKLIGHT_FREQ_SET 0x728
+
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MSB 0x72a
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_MID 0x72b
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MIN_LSB 0x72c
+
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MSB 0x72d
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_MID 0x72e
+#define DP_EDP_BACKLIGHT_FREQ_CAP_MAX_LSB 0x72f
+
+#define DP_EDP_DBC_MINIMUM_BRIGHTNESS_SET 0x732
+#define DP_EDP_DBC_MAXIMUM_BRIGHTNESS_SET 0x733
+
+#define DP_EDP_REGIONAL_BACKLIGHT_BASE 0x740 /* eDP 1.4 */
+#define DP_EDP_REGIONAL_BACKLIGHT_0 0x741 /* eDP 1.4 */
+
+#define DP_SIDEBAND_MSG_DOWN_REQ_BASE 0x1000 /* 1.2 MST */
+#define DP_SIDEBAND_MSG_UP_REP_BASE 0x1200 /* 1.2 MST */
+#define DP_SIDEBAND_MSG_DOWN_REP_BASE 0x1400 /* 1.2 MST */
+#define DP_SIDEBAND_MSG_UP_REQ_BASE 0x1600 /* 1.2 MST */
+
+#define DP_SINK_COUNT_ESI 0x2002 /* 1.2 */
+/* 0-5 sink count */
+# define DP_SINK_COUNT_CP_READY (1 << 6)
+
+#define DP_DEVICE_SERVICE_IRQ_VECTOR_ESI0 0x2003 /* 1.2 */
+
+#define DP_DEVICE_SERVICE_IRQ_VECTOR_ESI1 0x2004 /* 1.2 */
+
+#define DP_LINK_SERVICE_IRQ_VECTOR_ESI0 0x2005 /* 1.2 */
+
+#define DP_PSR_ERROR_STATUS 0x2006 /* XXX 1.2? */
+# define DP_PSR_LINK_CRC_ERROR (1 << 0)
+# define DP_PSR_RFB_STORAGE_ERROR (1 << 1)
+# define DP_PSR_VSC_SDP_UNCORRECTABLE_ERROR (1 << 2) /* eDP 1.4 */
+
+#define DP_PSR_ESI 0x2007 /* XXX 1.2? */
+# define DP_PSR_CAPS_CHANGE (1 << 0)
+
+#define DP_PSR_STATUS 0x2008 /* XXX 1.2? */
+# define DP_PSR_SINK_INACTIVE 0
+# define DP_PSR_SINK_ACTIVE_SRC_SYNCED 1
+# define DP_PSR_SINK_ACTIVE_RFB 2
+# define DP_PSR_SINK_ACTIVE_SINK_SYNCED 3
+# define DP_PSR_SINK_ACTIVE_RESYNC 4
+# define DP_PSR_SINK_INTERNAL_ERROR 7
+# define DP_PSR_SINK_STATE_MASK 0x07
+
+#define DP_RECEIVER_ALPM_STATUS 0x200b /* eDP 1.4 */
+# define DP_ALPM_LOCK_TIMEOUT_ERROR (1 << 0)
+
+/* DP 1.2 Sideband message defines */
+/* peer device type - DP 1.2a Table 2-92 */
+#define DP_PEER_DEVICE_NONE 0x0
+#define DP_PEER_DEVICE_SOURCE_OR_SST 0x1
+#define DP_PEER_DEVICE_MST_BRANCHING 0x2
+#define DP_PEER_DEVICE_SST_SINK 0x3
+#define DP_PEER_DEVICE_DP_LEGACY_CONV 0x4
+
+/* DP 1.2 MST sideband request names DP 1.2a Table 2-80 */
+#define DP_LINK_ADDRESS 0x01
+#define DP_CONNECTION_STATUS_NOTIFY 0x02
+#define DP_ENUM_PATH_RESOURCES 0x10
+#define DP_ALLOCATE_PAYLOAD 0x11
+#define DP_QUERY_PAYLOAD 0x12
+#define DP_RESOURCE_STATUS_NOTIFY 0x13
+#define DP_CLEAR_PAYLOAD_ID_TABLE 0x14
+#define DP_REMOTE_DPCD_READ 0x20
+#define DP_REMOTE_DPCD_WRITE 0x21
+#define DP_REMOTE_I2C_READ 0x22
+#define DP_REMOTE_I2C_WRITE 0x23
+#define DP_POWER_UP_PHY 0x24
+#define DP_POWER_DOWN_PHY 0x25
+#define DP_SINK_EVENT_NOTIFY 0x30
+#define DP_QUERY_STREAM_ENC_STATUS 0x38
+
+/* DP 1.2 MST sideband nak reasons - table 2.84 */
+#define DP_NAK_WRITE_FAILURE 0x01
+#define DP_NAK_INVALID_READ 0x02
+#define DP_NAK_CRC_FAILURE 0x03
+#define DP_NAK_BAD_PARAM 0x04
+#define DP_NAK_DEFER 0x05
+#define DP_NAK_LINK_FAILURE 0x06
+#define DP_NAK_NO_RESOURCES 0x07
+#define DP_NAK_DPCD_FAIL 0x08
+#define DP_NAK_I2C_NAK 0x09
+#define DP_NAK_ALLOCATE_FAIL 0x0a
+
+#define MODE_I2C_START 1
+#define MODE_I2C_WRITE 2
+#define MODE_I2C_READ 4
+#define MODE_I2C_STOP 8
+
+#define DP_LINK_STATUS_SIZE 6
+bool drm_dp_channel_eq_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
+ int lane_count);
+bool drm_dp_clock_recovery_ok(const u8 link_status[DP_LINK_STATUS_SIZE],
+ int lane_count);
+u8 drm_dp_get_adjust_request_voltage(const u8 link_status[DP_LINK_STATUS_SIZE],
+ int lane);
+u8 drm_dp_get_adjust_request_pre_emphasis(const u8 link_status[DP_LINK_STATUS_SIZE],
+ int lane);
+
+#define DP_RECEIVER_CAP_SIZE 0xf
+#define EDP_PSR_RECEIVER_CAP_SIZE 2
+
+void drm_dp_link_train_clock_recovery_delay(const u8 dpcd[DP_RECEIVER_CAP_SIZE]);
+void drm_dp_link_train_channel_eq_delay(const u8 dpcd[DP_RECEIVER_CAP_SIZE]);
+
+u8 drm_dp_link_rate_to_bw_code(int link_rate);
+int drm_dp_bw_code_to_link_rate(u8 link_bw);
+
+struct edp_sdp_header {
+ u8 HB0; /* Secondary Data Packet ID */
+ u8 HB1; /* Secondary Data Packet Type */
+ u8 HB2; /* 7:5 reserved, 4:0 revision number */
+ u8 HB3; /* 7:5 reserved, 4:0 number of valid data bytes */
+} __packed;
+
+#define EDP_SDP_HEADER_REVISION_MASK 0x1F
+#define EDP_SDP_HEADER_VALID_PAYLOAD_BYTES 0x1F
+
+struct edp_vsc_psr {
+ struct edp_sdp_header sdp_header;
+ u8 DB0; /* Stereo Interface */
+ u8 DB1; /* 0 - PSR State; 1 - Update RFB; 2 - CRC Valid */
+ u8 DB2; /* CRC value bits 7:0 of the R or Cr component */
+ u8 DB3; /* CRC value bits 15:8 of the R or Cr component */
+ u8 DB4; /* CRC value bits 7:0 of the G or Y component */
+ u8 DB5; /* CRC value bits 15:8 of the G or Y component */
+ u8 DB6; /* CRC value bits 7:0 of the B or Cb component */
+ u8 DB7; /* CRC value bits 15:8 of the B or Cb component */
+ u8 DB8_31[24]; /* Reserved */
+} __packed;
+
+#define EDP_VSC_PSR_STATE_ACTIVE (1<<0)
+#define EDP_VSC_PSR_UPDATE_RFB (1<<1)
+#define EDP_VSC_PSR_CRC_VALUES_VALID (1<<2)
+
+static inline int
+drm_dp_max_link_rate(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
+{
+ return drm_dp_bw_code_to_link_rate(dpcd[DP_MAX_LINK_RATE]);
+}
+
+static inline u8
+drm_dp_max_lane_count(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
+{
+ return dpcd[DP_MAX_LANE_COUNT] & DP_MAX_LANE_COUNT_MASK;
+}
+
+static inline bool
+drm_dp_enhanced_frame_cap(const u8 dpcd[DP_RECEIVER_CAP_SIZE])
+{
+ return dpcd[DP_DPCD_REV] >= 0x11 &&
+ (dpcd[DP_MAX_LANE_COUNT] & DP_ENHANCED_FRAME_CAP);
+}
+
+/*
+ * DisplayPort AUX channel
+ */
+
+/**
+ * struct drm_dp_aux_msg - DisplayPort AUX channel transaction
+ * @address: address of the (first) register to access
+ * @request: contains the type of transaction (see DP_AUX_* macros)
+ * @reply: upon completion, contains the reply type of the transaction
+ * @buffer: pointer to a transmission or reception buffer
+ * @size: size of @buffer
+ */
+struct drm_dp_aux_msg {
+ unsigned int address;
+ u8 request;
+ u8 reply;
+ void *buffer;
+ size_t size;
+};
+
+/**
+ * struct drm_dp_aux - DisplayPort AUX channel
+ * @name: user-visible name of this AUX channel and the I2C-over-AUX adapter
+ * @ddc: I2C adapter that can be used for I2C-over-AUX communication
+ * @dev: pointer to struct device that is the parent for this AUX channel
+ * @hw_mutex: internal mutex used for locking transfers
+ * @transfer: transfers a message representing a single AUX transaction
+ *
+ * The .dev field should be set to a pointer to the device that implements
+ * the AUX channel.
+ *
+ * The .name field may be used to specify the name of the I2C adapter. If set to
+ * NULL, dev_name() of .dev will be used.
+ *
+ * Drivers provide a hardware-specific implementation of how transactions
+ * are executed via the .transfer() function. A pointer to a drm_dp_aux_msg
+ * structure describing the transaction is passed into this function. Upon
+ * success, the implementation should return the number of payload bytes
+ * that were transferred, or a negative error-code on failure. Helpers
+ * propagate errors from the .transfer() function, with the exception of
+ * the -EBUSY error, which causes a transaction to be retried. On a short,
+ * helpers will return -EPROTO to make it simpler to check for failure.
+ *
+ * An AUX channel can also be used to transport I2C messages to a sink. A
+ * typical application of that is to access an EDID that's present in the
+ * sink device. The .transfer() function can also be used to execute such
+ * transactions. The drm_dp_aux_register_i2c_bus() function registers an
+ * I2C adapter that can be passed to drm_probe_ddc(). Upon removal, drivers
+ * should call drm_dp_aux_unregister_i2c_bus() to remove the I2C adapter.
+ * The I2C adapter uses long transfers by default; if a partial response is
+ * received, the adapter will drop down to the size given by the partial
+ * response for this transaction only.
+ *
+ * Note that the aux helper code assumes that the .transfer() function
+ * only modifies the reply field of the drm_dp_aux_msg structure. The
+ * retry logic and i2c helpers assume this is the case.
+ */
+struct drm_dp_aux {
+ const char *name;
+ struct i2c_adapter ddc;
+ struct device *dev;
+ struct mutex hw_mutex;
+ ssize_t (*transfer)(struct drm_dp_aux *aux,
+ struct drm_dp_aux_msg *msg);
+ unsigned i2c_nack_count, i2c_defer_count;
+};
+
+ssize_t drm_dp_dpcd_read(struct drm_dp_aux *aux, unsigned int offset,
+ void *buffer, size_t size);
+ssize_t drm_dp_dpcd_write(struct drm_dp_aux *aux, unsigned int offset,
+ void *buffer, size_t size);
+
+/**
+ * drm_dp_dpcd_readb() - read a single byte from the DPCD
+ * @aux: DisplayPort AUX channel
+ * @offset: address of the register to read
+ * @valuep: location where the value of the register will be stored
+ *
+ * Returns the number of bytes transferred (1) on success, or a negative
+ * error code on failure.
+ */
+static inline ssize_t drm_dp_dpcd_readb(struct drm_dp_aux *aux,
+ unsigned int offset, u8 *valuep)
+{
+ return drm_dp_dpcd_read(aux, offset, valuep, 1);
+}
+
+/**
+ * drm_dp_dpcd_writeb() - write a single byte to the DPCD
+ * @aux: DisplayPort AUX channel
+ * @offset: address of the register to write
+ * @value: value to write to the register
+ *
+ * Returns the number of bytes transferred (1) on success, or a negative
+ * error code on failure.
+ */
+static inline ssize_t drm_dp_dpcd_writeb(struct drm_dp_aux *aux,
+ unsigned int offset, u8 value)
+{
+ return drm_dp_dpcd_write(aux, offset, &value, 1);
+}
+
+int drm_dp_dpcd_read_link_status(struct drm_dp_aux *aux,
+ u8 status[DP_LINK_STATUS_SIZE]);
+
+/*
+ * DisplayPort link
+ */
+#define DP_LINK_CAP_ENHANCED_FRAMING (1 << 0)
+
+struct drm_dp_link {
+ unsigned char revision;
+ unsigned int rate;
+ unsigned int num_lanes;
+ unsigned long capabilities;
+};
+
+int drm_dp_link_probe(struct drm_dp_aux *aux, struct drm_dp_link *link);
+int drm_dp_link_power_up(struct drm_dp_aux *aux, struct drm_dp_link *link);
+int drm_dp_link_power_down(struct drm_dp_aux *aux, struct drm_dp_link *link);
+int drm_dp_link_configure(struct drm_dp_aux *aux, struct drm_dp_link *link);
+
+int drm_dp_aux_register(struct drm_dp_aux *aux);
+void drm_dp_aux_unregister(struct drm_dp_aux *aux);
+
+#endif /* _DRM_DP_HELPER_H_ */
Code Review / kvmfornfv.git / blobdiff