--- /dev/null
+/*
+ * linux/drivers/video/pxafb.c
+ *
+ * Copyright (C) 1999 Eric A. Thomas.
+ * Copyright (C) 2004 Jean-Frederic Clere.
+ * Copyright (C) 2004 Ian Campbell.
+ * Copyright (C) 2004 Jeff Lackey.
+ * Based on sa1100fb.c Copyright (C) 1999 Eric A. Thomas
+ * which in turn is
+ * Based on acornfb.c Copyright (C) Russell King.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file COPYING in the main directory of this archive for
+ * more details.
+ *
+ * Intel PXA250/210 LCD Controller Frame Buffer Driver
+ *
+ * Please direct your questions and comments on this driver to the following
+ * email address:
+ *
+ * linux-arm-kernel@lists.arm.linux.org.uk
+ *
+ * Add support for overlay1 and overlay2 based on pxafb_overlay.c:
+ *
+ * Copyright (C) 2004, Intel Corporation
+ *
+ * 2003/08/27: <yu.tang@intel.com>
+ * 2004/03/10: <stanley.cai@intel.com>
+ * 2004/10/28: <yan.yin@intel.com>
+ *
+ * Copyright (C) 2006-2008 Marvell International Ltd.
+ * All Rights Reserved
+ */
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/interrupt.h>
+#include <linux/slab.h>
+#include <linux/mm.h>
+#include <linux/fb.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/completion.h>
+#include <linux/mutex.h>
+#include <linux/kthread.h>
+#include <linux/freezer.h>
+#include <linux/console.h>
+
+#include <mach/hardware.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/div64.h>
+#include <mach/bitfield.h>
+#include <linux/platform_data/video-pxafb.h>
+
+/*
+ * Complain if VAR is out of range.
+ */
+#define DEBUG_VAR 1
+
+#include "pxafb.h"
+
+/* Bits which should not be set in machine configuration structures */
+#define LCCR0_INVALID_CONFIG_MASK (LCCR0_OUM | LCCR0_BM | LCCR0_QDM |\
+ LCCR0_DIS | LCCR0_EFM | LCCR0_IUM |\
+ LCCR0_SFM | LCCR0_LDM | LCCR0_ENB)
+
+#define LCCR3_INVALID_CONFIG_MASK (LCCR3_HSP | LCCR3_VSP |\
+ LCCR3_PCD | LCCR3_BPP(0xf))
+
+static int pxafb_activate_var(struct fb_var_screeninfo *var,
+ struct pxafb_info *);
+static void set_ctrlr_state(struct pxafb_info *fbi, u_int state);
+static void setup_base_frame(struct pxafb_info *fbi,
+ struct fb_var_screeninfo *var, int branch);
+static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
+ unsigned long offset, size_t size);
+
+static unsigned long video_mem_size = 0;
+
+static inline unsigned long
+lcd_readl(struct pxafb_info *fbi, unsigned int off)
+{
+ return __raw_readl(fbi->mmio_base + off);
+}
+
+static inline void
+lcd_writel(struct pxafb_info *fbi, unsigned int off, unsigned long val)
+{
+ __raw_writel(val, fbi->mmio_base + off);
+}
+
+static inline void pxafb_schedule_work(struct pxafb_info *fbi, u_int state)
+{
+ unsigned long flags;
+
+ local_irq_save(flags);
+ /*
+ * We need to handle two requests being made at the same time.
+ * There are two important cases:
+ * 1. When we are changing VT (C_REENABLE) while unblanking
+ * (C_ENABLE) We must perform the unblanking, which will
+ * do our REENABLE for us.
+ * 2. When we are blanking, but immediately unblank before
+ * we have blanked. We do the "REENABLE" thing here as
+ * well, just to be sure.
+ */
+ if (fbi->task_state == C_ENABLE && state == C_REENABLE)
+ state = (u_int) -1;
+ if (fbi->task_state == C_DISABLE && state == C_ENABLE)
+ state = C_REENABLE;
+
+ if (state != (u_int)-1) {
+ fbi->task_state = state;
+ schedule_work(&fbi->task);
+ }
+ local_irq_restore(flags);
+}
+
+static inline u_int chan_to_field(u_int chan, struct fb_bitfield *bf)
+{
+ chan &= 0xffff;
+ chan >>= 16 - bf->length;
+ return chan << bf->offset;
+}
+
+static int
+pxafb_setpalettereg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int trans, struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ u_int val;
+
+ if (regno >= fbi->palette_size)
+ return 1;
+
+ if (fbi->fb.var.grayscale) {
+ fbi->palette_cpu[regno] = ((blue >> 8) & 0x00ff);
+ return 0;
+ }
+
+ switch (fbi->lccr4 & LCCR4_PAL_FOR_MASK) {
+ case LCCR4_PAL_FOR_0:
+ val = ((red >> 0) & 0xf800);
+ val |= ((green >> 5) & 0x07e0);
+ val |= ((blue >> 11) & 0x001f);
+ fbi->palette_cpu[regno] = val;
+ break;
+ case LCCR4_PAL_FOR_1:
+ val = ((red << 8) & 0x00f80000);
+ val |= ((green >> 0) & 0x0000fc00);
+ val |= ((blue >> 8) & 0x000000f8);
+ ((u32 *)(fbi->palette_cpu))[regno] = val;
+ break;
+ case LCCR4_PAL_FOR_2:
+ val = ((red << 8) & 0x00fc0000);
+ val |= ((green >> 0) & 0x0000fc00);
+ val |= ((blue >> 8) & 0x000000fc);
+ ((u32 *)(fbi->palette_cpu))[regno] = val;
+ break;
+ case LCCR4_PAL_FOR_3:
+ val = ((red << 8) & 0x00ff0000);
+ val |= ((green >> 0) & 0x0000ff00);
+ val |= ((blue >> 8) & 0x000000ff);
+ ((u32 *)(fbi->palette_cpu))[regno] = val;
+ break;
+ }
+
+ return 0;
+}
+
+static int
+pxafb_setcolreg(u_int regno, u_int red, u_int green, u_int blue,
+ u_int trans, struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ unsigned int val;
+ int ret = 1;
+
+ /*
+ * If inverse mode was selected, invert all the colours
+ * rather than the register number. The register number
+ * is what you poke into the framebuffer to produce the
+ * colour you requested.
+ */
+ if (fbi->cmap_inverse) {
+ red = 0xffff - red;
+ green = 0xffff - green;
+ blue = 0xffff - blue;
+ }
+
+ /*
+ * If greyscale is true, then we convert the RGB value
+ * to greyscale no matter what visual we are using.
+ */
+ if (fbi->fb.var.grayscale)
+ red = green = blue = (19595 * red + 38470 * green +
+ 7471 * blue) >> 16;
+
+ switch (fbi->fb.fix.visual) {
+ case FB_VISUAL_TRUECOLOR:
+ /*
+ * 16-bit True Colour. We encode the RGB value
+ * according to the RGB bitfield information.
+ */
+ if (regno < 16) {
+ u32 *pal = fbi->fb.pseudo_palette;
+
+ val = chan_to_field(red, &fbi->fb.var.red);
+ val |= chan_to_field(green, &fbi->fb.var.green);
+ val |= chan_to_field(blue, &fbi->fb.var.blue);
+
+ pal[regno] = val;
+ ret = 0;
+ }
+ break;
+
+ case FB_VISUAL_STATIC_PSEUDOCOLOR:
+ case FB_VISUAL_PSEUDOCOLOR:
+ ret = pxafb_setpalettereg(regno, red, green, blue, trans, info);
+ break;
+ }
+
+ return ret;
+}
+
+/* calculate pixel depth, transparency bit included, >=16bpp formats _only_ */
+static inline int var_to_depth(struct fb_var_screeninfo *var)
+{
+ return var->red.length + var->green.length +
+ var->blue.length + var->transp.length;
+}
+
+/* calculate 4-bit BPP value for LCCR3 and OVLxC1 */
+static int pxafb_var_to_bpp(struct fb_var_screeninfo *var)
+{
+ int bpp = -EINVAL;
+
+ switch (var->bits_per_pixel) {
+ case 1: bpp = 0; break;
+ case 2: bpp = 1; break;
+ case 4: bpp = 2; break;
+ case 8: bpp = 3; break;
+ case 16: bpp = 4; break;
+ case 24:
+ switch (var_to_depth(var)) {
+ case 18: bpp = 6; break; /* 18-bits/pixel packed */
+ case 19: bpp = 8; break; /* 19-bits/pixel packed */
+ case 24: bpp = 9; break;
+ }
+ break;
+ case 32:
+ switch (var_to_depth(var)) {
+ case 18: bpp = 5; break; /* 18-bits/pixel unpacked */
+ case 19: bpp = 7; break; /* 19-bits/pixel unpacked */
+ case 25: bpp = 10; break;
+ }
+ break;
+ }
+ return bpp;
+}
+
+/*
+ * pxafb_var_to_lccr3():
+ * Convert a bits per pixel value to the correct bit pattern for LCCR3
+ *
+ * NOTE: for PXA27x with overlays support, the LCCR3_PDFOR_x bits have an
+ * implication of the acutal use of transparency bit, which we handle it
+ * here separatedly. See PXA27x Developer's Manual, Section <<7.4.6 Pixel
+ * Formats>> for the valid combination of PDFOR, PAL_FOR for various BPP.
+ *
+ * Transparency for palette pixel formats is not supported at the moment.
+ */
+static uint32_t pxafb_var_to_lccr3(struct fb_var_screeninfo *var)
+{
+ int bpp = pxafb_var_to_bpp(var);
+ uint32_t lccr3;
+
+ if (bpp < 0)
+ return 0;
+
+ lccr3 = LCCR3_BPP(bpp);
+
+ switch (var_to_depth(var)) {
+ case 16: lccr3 |= var->transp.length ? LCCR3_PDFOR_3 : 0; break;
+ case 18: lccr3 |= LCCR3_PDFOR_3; break;
+ case 24: lccr3 |= var->transp.length ? LCCR3_PDFOR_2 : LCCR3_PDFOR_3;
+ break;
+ case 19:
+ case 25: lccr3 |= LCCR3_PDFOR_0; break;
+ }
+ return lccr3;
+}
+
+#define SET_PIXFMT(v, r, g, b, t) \
+({ \
+ (v)->transp.offset = (t) ? (r) + (g) + (b) : 0; \
+ (v)->transp.length = (t) ? (t) : 0; \
+ (v)->blue.length = (b); (v)->blue.offset = 0; \
+ (v)->green.length = (g); (v)->green.offset = (b); \
+ (v)->red.length = (r); (v)->red.offset = (b) + (g); \
+})
+
+/* set the RGBT bitfields of fb_var_screeninf according to
+ * var->bits_per_pixel and given depth
+ */
+static void pxafb_set_pixfmt(struct fb_var_screeninfo *var, int depth)
+{
+ if (depth == 0)
+ depth = var->bits_per_pixel;
+
+ if (var->bits_per_pixel < 16) {
+ /* indexed pixel formats */
+ var->red.offset = 0; var->red.length = 8;
+ var->green.offset = 0; var->green.length = 8;
+ var->blue.offset = 0; var->blue.length = 8;
+ var->transp.offset = 0; var->transp.length = 8;
+ }
+
+ switch (depth) {
+ case 16: var->transp.length ?
+ SET_PIXFMT(var, 5, 5, 5, 1) : /* RGBT555 */
+ SET_PIXFMT(var, 5, 6, 5, 0); break; /* RGB565 */
+ case 18: SET_PIXFMT(var, 6, 6, 6, 0); break; /* RGB666 */
+ case 19: SET_PIXFMT(var, 6, 6, 6, 1); break; /* RGBT666 */
+ case 24: var->transp.length ?
+ SET_PIXFMT(var, 8, 8, 7, 1) : /* RGBT887 */
+ SET_PIXFMT(var, 8, 8, 8, 0); break; /* RGB888 */
+ case 25: SET_PIXFMT(var, 8, 8, 8, 1); break; /* RGBT888 */
+ }
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * pxafb_display_dma_period()
+ * Calculate the minimum period (in picoseconds) between two DMA
+ * requests for the LCD controller. If we hit this, it means we're
+ * doing nothing but LCD DMA.
+ */
+static unsigned int pxafb_display_dma_period(struct fb_var_screeninfo *var)
+{
+ /*
+ * Period = pixclock * bits_per_byte * bytes_per_transfer
+ * / memory_bits_per_pixel;
+ */
+ return var->pixclock * 8 * 16 / var->bits_per_pixel;
+}
+#endif
+
+/*
+ * Select the smallest mode that allows the desired resolution to be
+ * displayed. If desired parameters can be rounded up.
+ */
+static struct pxafb_mode_info *pxafb_getmode(struct pxafb_mach_info *mach,
+ struct fb_var_screeninfo *var)
+{
+ struct pxafb_mode_info *mode = NULL;
+ struct pxafb_mode_info *modelist = mach->modes;
+ unsigned int best_x = 0xffffffff, best_y = 0xffffffff;
+ unsigned int i;
+
+ for (i = 0; i < mach->num_modes; i++) {
+ if (modelist[i].xres >= var->xres &&
+ modelist[i].yres >= var->yres &&
+ modelist[i].xres < best_x &&
+ modelist[i].yres < best_y &&
+ modelist[i].bpp >= var->bits_per_pixel) {
+ best_x = modelist[i].xres;
+ best_y = modelist[i].yres;
+ mode = &modelist[i];
+ }
+ }
+
+ return mode;
+}
+
+static void pxafb_setmode(struct fb_var_screeninfo *var,
+ struct pxafb_mode_info *mode)
+{
+ var->xres = mode->xres;
+ var->yres = mode->yres;
+ var->bits_per_pixel = mode->bpp;
+ var->pixclock = mode->pixclock;
+ var->hsync_len = mode->hsync_len;
+ var->left_margin = mode->left_margin;
+ var->right_margin = mode->right_margin;
+ var->vsync_len = mode->vsync_len;
+ var->upper_margin = mode->upper_margin;
+ var->lower_margin = mode->lower_margin;
+ var->sync = mode->sync;
+ var->grayscale = mode->cmap_greyscale;
+ var->transp.length = mode->transparency;
+
+ /* set the initial RGBA bitfields */
+ pxafb_set_pixfmt(var, mode->depth);
+}
+
+static int pxafb_adjust_timing(struct pxafb_info *fbi,
+ struct fb_var_screeninfo *var)
+{
+ int line_length;
+
+ var->xres = max_t(int, var->xres, MIN_XRES);
+ var->yres = max_t(int, var->yres, MIN_YRES);
+
+ if (!(fbi->lccr0 & LCCR0_LCDT)) {
+ clamp_val(var->hsync_len, 1, 64);
+ clamp_val(var->vsync_len, 1, 64);
+ clamp_val(var->left_margin, 1, 255);
+ clamp_val(var->right_margin, 1, 255);
+ clamp_val(var->upper_margin, 1, 255);
+ clamp_val(var->lower_margin, 1, 255);
+ }
+
+ /* make sure each line is aligned on word boundary */
+ line_length = var->xres * var->bits_per_pixel / 8;
+ line_length = ALIGN(line_length, 4);
+ var->xres = line_length * 8 / var->bits_per_pixel;
+
+ /* we don't support xpan, force xres_virtual to be equal to xres */
+ var->xres_virtual = var->xres;
+
+ if (var->accel_flags & FB_ACCELF_TEXT)
+ var->yres_virtual = fbi->fb.fix.smem_len / line_length;
+ else
+ var->yres_virtual = max(var->yres_virtual, var->yres);
+
+ /* check for limits */
+ if (var->xres > MAX_XRES || var->yres > MAX_YRES)
+ return -EINVAL;
+
+ if (var->yres > var->yres_virtual)
+ return -EINVAL;
+
+ return 0;
+}
+
+/*
+ * pxafb_check_var():
+ * Get the video params out of 'var'. If a value doesn't fit, round it up,
+ * if it's too big, return -EINVAL.
+ *
+ * Round up in the following order: bits_per_pixel, xres,
+ * yres, xres_virtual, yres_virtual, xoffset, yoffset, grayscale,
+ * bitfields, horizontal timing, vertical timing.
+ */
+static int pxafb_check_var(struct fb_var_screeninfo *var, struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ struct pxafb_mach_info *inf = dev_get_platdata(fbi->dev);
+ int err;
+
+ if (inf->fixed_modes) {
+ struct pxafb_mode_info *mode;
+
+ mode = pxafb_getmode(inf, var);
+ if (!mode)
+ return -EINVAL;
+ pxafb_setmode(var, mode);
+ }
+
+ /* do a test conversion to BPP fields to check the color formats */
+ err = pxafb_var_to_bpp(var);
+ if (err < 0)
+ return err;
+
+ pxafb_set_pixfmt(var, var_to_depth(var));
+
+ err = pxafb_adjust_timing(fbi, var);
+ if (err)
+ return err;
+
+#ifdef CONFIG_CPU_FREQ
+ pr_debug("pxafb: dma period = %d ps\n",
+ pxafb_display_dma_period(var));
+#endif
+
+ return 0;
+}
+
+/*
+ * pxafb_set_par():
+ * Set the user defined part of the display for the specified console
+ */
+static int pxafb_set_par(struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ struct fb_var_screeninfo *var = &info->var;
+
+ if (var->bits_per_pixel >= 16)
+ fbi->fb.fix.visual = FB_VISUAL_TRUECOLOR;
+ else if (!fbi->cmap_static)
+ fbi->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR;
+ else {
+ /*
+ * Some people have weird ideas about wanting static
+ * pseudocolor maps. I suspect their user space
+ * applications are broken.
+ */
+ fbi->fb.fix.visual = FB_VISUAL_STATIC_PSEUDOCOLOR;
+ }
+
+ fbi->fb.fix.line_length = var->xres_virtual *
+ var->bits_per_pixel / 8;
+ if (var->bits_per_pixel >= 16)
+ fbi->palette_size = 0;
+ else
+ fbi->palette_size = var->bits_per_pixel == 1 ?
+ 4 : 1 << var->bits_per_pixel;
+
+ fbi->palette_cpu = (u16 *)&fbi->dma_buff->palette[0];
+
+ if (fbi->fb.var.bits_per_pixel >= 16)
+ fb_dealloc_cmap(&fbi->fb.cmap);
+ else
+ fb_alloc_cmap(&fbi->fb.cmap, 1<<fbi->fb.var.bits_per_pixel, 0);
+
+ pxafb_activate_var(var, fbi);
+
+ return 0;
+}
+
+static int pxafb_pan_display(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ struct fb_var_screeninfo newvar;
+ int dma = DMA_MAX + DMA_BASE;
+
+ if (fbi->state != C_ENABLE)
+ return 0;
+
+ /* Only take .xoffset, .yoffset and .vmode & FB_VMODE_YWRAP from what
+ * was passed in and copy the rest from the old screeninfo.
+ */
+ memcpy(&newvar, &fbi->fb.var, sizeof(newvar));
+ newvar.xoffset = var->xoffset;
+ newvar.yoffset = var->yoffset;
+ newvar.vmode &= ~FB_VMODE_YWRAP;
+ newvar.vmode |= var->vmode & FB_VMODE_YWRAP;
+
+ setup_base_frame(fbi, &newvar, 1);
+
+ if (fbi->lccr0 & LCCR0_SDS)
+ lcd_writel(fbi, FBR1, fbi->fdadr[dma + 1] | 0x1);
+
+ lcd_writel(fbi, FBR0, fbi->fdadr[dma] | 0x1);
+ return 0;
+}
+
+/*
+ * pxafb_blank():
+ * Blank the display by setting all palette values to zero. Note, the
+ * 16 bpp mode does not really use the palette, so this will not
+ * blank the display in all modes.
+ */
+static int pxafb_blank(int blank, struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ int i;
+
+ switch (blank) {
+ case FB_BLANK_POWERDOWN:
+ case FB_BLANK_VSYNC_SUSPEND:
+ case FB_BLANK_HSYNC_SUSPEND:
+ case FB_BLANK_NORMAL:
+ if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
+ fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
+ for (i = 0; i < fbi->palette_size; i++)
+ pxafb_setpalettereg(i, 0, 0, 0, 0, info);
+
+ pxafb_schedule_work(fbi, C_DISABLE);
+ /* TODO if (pxafb_blank_helper) pxafb_blank_helper(blank); */
+ break;
+
+ case FB_BLANK_UNBLANK:
+ /* TODO if (pxafb_blank_helper) pxafb_blank_helper(blank); */
+ if (fbi->fb.fix.visual == FB_VISUAL_PSEUDOCOLOR ||
+ fbi->fb.fix.visual == FB_VISUAL_STATIC_PSEUDOCOLOR)
+ fb_set_cmap(&fbi->fb.cmap, info);
+ pxafb_schedule_work(fbi, C_ENABLE);
+ }
+ return 0;
+}
+
+static struct fb_ops pxafb_ops = {
+ .owner = THIS_MODULE,
+ .fb_check_var = pxafb_check_var,
+ .fb_set_par = pxafb_set_par,
+ .fb_pan_display = pxafb_pan_display,
+ .fb_setcolreg = pxafb_setcolreg,
+ .fb_fillrect = cfb_fillrect,
+ .fb_copyarea = cfb_copyarea,
+ .fb_imageblit = cfb_imageblit,
+ .fb_blank = pxafb_blank,
+};
+
+#ifdef CONFIG_FB_PXA_OVERLAY
+static void overlay1fb_setup(struct pxafb_layer *ofb)
+{
+ int size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ unsigned long start = ofb->video_mem_phys;
+ setup_frame_dma(ofb->fbi, DMA_OV1, PAL_NONE, start, size);
+}
+
+/* Depending on the enable status of overlay1/2, the DMA should be
+ * updated from FDADRx (when disabled) or FBRx (when enabled).
+ */
+static void overlay1fb_enable(struct pxafb_layer *ofb)
+{
+ int enabled = lcd_readl(ofb->fbi, OVL1C1) & OVLxC1_OEN;
+ uint32_t fdadr1 = ofb->fbi->fdadr[DMA_OV1] | (enabled ? 0x1 : 0);
+
+ lcd_writel(ofb->fbi, enabled ? FBR1 : FDADR1, fdadr1);
+ lcd_writel(ofb->fbi, OVL1C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay1fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5;
+
+ if (!(lcd_readl(ofb->fbi, OVL1C1) & OVLxC1_OEN))
+ return;
+
+ lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL1C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(1));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(1));
+ lcd_writel(ofb->fbi, FBR1, ofb->fbi->fdadr[DMA_OV1] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay1\n", __func__);
+
+ lcd_writel(ofb->fbi, LCCR5, lccr5);
+}
+
+static void overlay2fb_setup(struct pxafb_layer *ofb)
+{
+ int size, div = 1, pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ unsigned long start[3] = { ofb->video_mem_phys, 0, 0 };
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED) {
+ size = ofb->fb.fix.line_length * ofb->fb.var.yres_virtual;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ } else {
+ size = ofb->fb.var.xres_virtual * ofb->fb.var.yres_virtual;
+ switch (pfor) {
+ case OVERLAY_FORMAT_YUV444_PLANAR: div = 1; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: div = 2; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: div = 4; break;
+ }
+ start[1] = start[0] + size;
+ start[2] = start[1] + size / div;
+ setup_frame_dma(ofb->fbi, DMA_OV2_Y, -1, start[0], size);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cb, -1, start[1], size / div);
+ setup_frame_dma(ofb->fbi, DMA_OV2_Cr, -1, start[2], size / div);
+ }
+}
+
+static void overlay2fb_enable(struct pxafb_layer *ofb)
+{
+ int pfor = NONSTD_TO_PFOR(ofb->fb.var.nonstd);
+ int enabled = lcd_readl(ofb->fbi, OVL2C1) & OVLxC1_OEN;
+ uint32_t fdadr2 = ofb->fbi->fdadr[DMA_OV2_Y] | (enabled ? 0x1 : 0);
+ uint32_t fdadr3 = ofb->fbi->fdadr[DMA_OV2_Cb] | (enabled ? 0x1 : 0);
+ uint32_t fdadr4 = ofb->fbi->fdadr[DMA_OV2_Cr] | (enabled ? 0x1 : 0);
+
+ if (pfor == OVERLAY_FORMAT_RGB || pfor == OVERLAY_FORMAT_YUV444_PACKED)
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ else {
+ lcd_writel(ofb->fbi, enabled ? FBR2 : FDADR2, fdadr2);
+ lcd_writel(ofb->fbi, enabled ? FBR3 : FDADR3, fdadr3);
+ lcd_writel(ofb->fbi, enabled ? FBR4 : FDADR4, fdadr4);
+ }
+ lcd_writel(ofb->fbi, OVL2C2, ofb->control[1]);
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] | OVLxC1_OEN);
+}
+
+static void overlay2fb_disable(struct pxafb_layer *ofb)
+{
+ uint32_t lccr5;
+
+ if (!(lcd_readl(ofb->fbi, OVL2C1) & OVLxC1_OEN))
+ return;
+
+ lccr5 = lcd_readl(ofb->fbi, LCCR5);
+
+ lcd_writel(ofb->fbi, OVL2C1, ofb->control[0] & ~OVLxC1_OEN);
+
+ lcd_writel(ofb->fbi, LCSR1, LCSR1_BS(2));
+ lcd_writel(ofb->fbi, LCCR5, lccr5 & ~LCSR1_BS(2));
+ lcd_writel(ofb->fbi, FBR2, ofb->fbi->fdadr[DMA_OV2_Y] | 0x3);
+ lcd_writel(ofb->fbi, FBR3, ofb->fbi->fdadr[DMA_OV2_Cb] | 0x3);
+ lcd_writel(ofb->fbi, FBR4, ofb->fbi->fdadr[DMA_OV2_Cr] | 0x3);
+
+ if (wait_for_completion_timeout(&ofb->branch_done, 1 * HZ) == 0)
+ pr_warning("%s: timeout disabling overlay2\n", __func__);
+}
+
+static struct pxafb_layer_ops ofb_ops[] = {
+ [0] = {
+ .enable = overlay1fb_enable,
+ .disable = overlay1fb_disable,
+ .setup = overlay1fb_setup,
+ },
+ [1] = {
+ .enable = overlay2fb_enable,
+ .disable = overlay2fb_disable,
+ .setup = overlay2fb_setup,
+ },
+};
+
+static int overlayfb_open(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = container_of(info, struct pxafb_layer, fb);
+
+ /* no support for framebuffer console on overlay */
+ if (user == 0)
+ return -ENODEV;
+
+ if (ofb->usage++ == 0) {
+ /* unblank the base framebuffer */
+ console_lock();
+ fb_blank(&ofb->fbi->fb, FB_BLANK_UNBLANK);
+ console_unlock();
+ }
+
+ return 0;
+}
+
+static int overlayfb_release(struct fb_info *info, int user)
+{
+ struct pxafb_layer *ofb = container_of(info, struct pxafb_layer, fb);
+
+ if (ofb->usage == 1) {
+ ofb->ops->disable(ofb);
+ ofb->fb.var.height = -1;
+ ofb->fb.var.width = -1;
+ ofb->fb.var.xres = ofb->fb.var.xres_virtual = 0;
+ ofb->fb.var.yres = ofb->fb.var.yres_virtual = 0;
+
+ ofb->usage--;
+ }
+ return 0;
+}
+
+static int overlayfb_check_var(struct fb_var_screeninfo *var,
+ struct fb_info *info)
+{
+ struct pxafb_layer *ofb = container_of(info, struct pxafb_layer, fb);
+ struct fb_var_screeninfo *base_var = &ofb->fbi->fb.var;
+ int xpos, ypos, pfor, bpp;
+
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_YPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ /* no support for YUV format on overlay1 */
+ if (ofb->id == OVERLAY1 && pfor != 0)
+ return -EINVAL;
+
+ /* for YUV packed formats, bpp = 'minimum bpp of YUV components' */
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB:
+ bpp = pxafb_var_to_bpp(var);
+ if (bpp < 0)
+ return -EINVAL;
+
+ pxafb_set_pixfmt(var, var_to_depth(var));
+ break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 8; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 4; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 2; break;
+ default:
+ return -EINVAL;
+ }
+
+ /* each line must start at a 32-bit word boundary */
+ if ((xpos * bpp) % 32)
+ return -EINVAL;
+
+ /* xres must align on 32-bit word boundary */
+ var->xres = roundup(var->xres * bpp, 32) / bpp;
+
+ if ((xpos + var->xres > base_var->xres) ||
+ (ypos + var->yres > base_var->yres))
+ return -EINVAL;
+
+ var->xres_virtual = var->xres;
+ var->yres_virtual = max(var->yres, var->yres_virtual);
+ return 0;
+}
+
+static int overlayfb_check_video_memory(struct pxafb_layer *ofb)
+{
+ struct fb_var_screeninfo *var = &ofb->fb.var;
+ int pfor = NONSTD_TO_PFOR(var->nonstd);
+ int size, bpp = 0;
+
+ switch (pfor) {
+ case OVERLAY_FORMAT_RGB: bpp = var->bits_per_pixel; break;
+ case OVERLAY_FORMAT_YUV444_PACKED: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV444_PLANAR: bpp = 24; break;
+ case OVERLAY_FORMAT_YUV422_PLANAR: bpp = 16; break;
+ case OVERLAY_FORMAT_YUV420_PLANAR: bpp = 12; break;
+ }
+
+ ofb->fb.fix.line_length = var->xres_virtual * bpp / 8;
+
+ size = PAGE_ALIGN(ofb->fb.fix.line_length * var->yres_virtual);
+
+ if (ofb->video_mem) {
+ if (ofb->video_mem_size >= size)
+ return 0;
+ }
+ return -EINVAL;
+}
+
+static int overlayfb_set_par(struct fb_info *info)
+{
+ struct pxafb_layer *ofb = container_of(info, struct pxafb_layer, fb);
+ struct fb_var_screeninfo *var = &info->var;
+ int xpos, ypos, pfor, bpp, ret;
+
+ ret = overlayfb_check_video_memory(ofb);
+ if (ret)
+ return ret;
+
+ bpp = pxafb_var_to_bpp(var);
+ xpos = NONSTD_TO_XPOS(var->nonstd);
+ ypos = NONSTD_TO_YPOS(var->nonstd);
+ pfor = NONSTD_TO_PFOR(var->nonstd);
+
+ ofb->control[0] = OVLxC1_PPL(var->xres) | OVLxC1_LPO(var->yres) |
+ OVLxC1_BPP(bpp);
+ ofb->control[1] = OVLxC2_XPOS(xpos) | OVLxC2_YPOS(ypos);
+
+ if (ofb->id == OVERLAY2)
+ ofb->control[1] |= OVL2C2_PFOR(pfor);
+
+ ofb->ops->setup(ofb);
+ ofb->ops->enable(ofb);
+ return 0;
+}
+
+static struct fb_ops overlay_fb_ops = {
+ .owner = THIS_MODULE,
+ .fb_open = overlayfb_open,
+ .fb_release = overlayfb_release,
+ .fb_check_var = overlayfb_check_var,
+ .fb_set_par = overlayfb_set_par,
+};
+
+static void init_pxafb_overlay(struct pxafb_info *fbi, struct pxafb_layer *ofb,
+ int id)
+{
+ sprintf(ofb->fb.fix.id, "overlay%d", id + 1);
+
+ ofb->fb.fix.type = FB_TYPE_PACKED_PIXELS;
+ ofb->fb.fix.xpanstep = 0;
+ ofb->fb.fix.ypanstep = 1;
+
+ ofb->fb.var.activate = FB_ACTIVATE_NOW;
+ ofb->fb.var.height = -1;
+ ofb->fb.var.width = -1;
+ ofb->fb.var.vmode = FB_VMODE_NONINTERLACED;
+
+ ofb->fb.fbops = &overlay_fb_ops;
+ ofb->fb.flags = FBINFO_FLAG_DEFAULT;
+ ofb->fb.node = -1;
+ ofb->fb.pseudo_palette = NULL;
+
+ ofb->id = id;
+ ofb->ops = &ofb_ops[id];
+ ofb->usage = 0;
+ ofb->fbi = fbi;
+ init_completion(&ofb->branch_done);
+}
+
+static inline int pxafb_overlay_supported(void)
+{
+ if (cpu_is_pxa27x() || cpu_is_pxa3xx())
+ return 1;
+
+ return 0;
+}
+
+static int pxafb_overlay_map_video_memory(struct pxafb_info *pxafb,
+ struct pxafb_layer *ofb)
+{
+ /* We assume that user will use at most video_mem_size for overlay fb,
+ * anyway, it's useless to use 16bpp main plane and 24bpp overlay
+ */
+ ofb->video_mem = alloc_pages_exact(PAGE_ALIGN(pxafb->video_mem_size),
+ GFP_KERNEL | __GFP_ZERO);
+ if (ofb->video_mem == NULL)
+ return -ENOMEM;
+
+ ofb->video_mem_phys = virt_to_phys(ofb->video_mem);
+ ofb->video_mem_size = PAGE_ALIGN(pxafb->video_mem_size);
+
+ mutex_lock(&ofb->fb.mm_lock);
+ ofb->fb.fix.smem_start = ofb->video_mem_phys;
+ ofb->fb.fix.smem_len = pxafb->video_mem_size;
+ mutex_unlock(&ofb->fb.mm_lock);
+
+ ofb->fb.screen_base = ofb->video_mem;
+
+ return 0;
+}
+
+static void pxafb_overlay_init(struct pxafb_info *fbi)
+{
+ int i, ret;
+
+ if (!pxafb_overlay_supported())
+ return;
+
+ for (i = 0; i < 2; i++) {
+ struct pxafb_layer *ofb = &fbi->overlay[i];
+ init_pxafb_overlay(fbi, ofb, i);
+ ret = register_framebuffer(&ofb->fb);
+ if (ret) {
+ dev_err(fbi->dev, "failed to register overlay %d\n", i);
+ continue;
+ }
+ ret = pxafb_overlay_map_video_memory(fbi, ofb);
+ if (ret) {
+ dev_err(fbi->dev,
+ "failed to map video memory for overlay %d\n",
+ i);
+ unregister_framebuffer(&ofb->fb);
+ continue;
+ }
+ ofb->registered = 1;
+ }
+
+ /* mask all IU/BS/EOF/SOF interrupts */
+ lcd_writel(fbi, LCCR5, ~0);
+
+ pr_info("PXA Overlay driver loaded successfully!\n");
+}
+
+static void pxafb_overlay_exit(struct pxafb_info *fbi)
+{
+ int i;
+
+ if (!pxafb_overlay_supported())
+ return;
+
+ for (i = 0; i < 2; i++) {
+ struct pxafb_layer *ofb = &fbi->overlay[i];
+ if (ofb->registered) {
+ if (ofb->video_mem)
+ free_pages_exact(ofb->video_mem,
+ ofb->video_mem_size);
+ unregister_framebuffer(&ofb->fb);
+ }
+ }
+}
+#else
+static inline void pxafb_overlay_init(struct pxafb_info *fbi) {}
+static inline void pxafb_overlay_exit(struct pxafb_info *fbi) {}
+#endif /* CONFIG_FB_PXA_OVERLAY */
+
+/*
+ * Calculate the PCD value from the clock rate (in picoseconds).
+ * We take account of the PPCR clock setting.
+ * From PXA Developer's Manual:
+ *
+ * PixelClock = LCLK
+ * -------------
+ * 2 ( PCD + 1 )
+ *
+ * PCD = LCLK
+ * ------------- - 1
+ * 2(PixelClock)
+ *
+ * Where:
+ * LCLK = LCD/Memory Clock
+ * PCD = LCCR3[7:0]
+ *
+ * PixelClock here is in Hz while the pixclock argument given is the
+ * period in picoseconds. Hence PixelClock = 1 / ( pixclock * 10^-12 )
+ *
+ * The function get_lclk_frequency_10khz returns LCLK in units of
+ * 10khz. Calling the result of this function lclk gives us the
+ * following
+ *
+ * PCD = (lclk * 10^4 ) * ( pixclock * 10^-12 )
+ * -------------------------------------- - 1
+ * 2
+ *
+ * Factoring the 10^4 and 10^-12 out gives 10^-8 == 1 / 100000000 as used below.
+ */
+static inline unsigned int get_pcd(struct pxafb_info *fbi,
+ unsigned int pixclock)
+{
+ unsigned long long pcd;
+
+ /* FIXME: Need to take into account Double Pixel Clock mode
+ * (DPC) bit? or perhaps set it based on the various clock
+ * speeds */
+ pcd = (unsigned long long)(clk_get_rate(fbi->clk) / 10000);
+ pcd *= pixclock;
+ do_div(pcd, 100000000 * 2);
+ /* no need for this, since we should subtract 1 anyway. they cancel */
+ /* pcd += 1; */ /* make up for integer math truncations */
+ return (unsigned int)pcd;
+}
+
+/*
+ * Some touchscreens need hsync information from the video driver to
+ * function correctly. We export it here. Note that 'hsync_time' and
+ * the value returned from pxafb_get_hsync_time() is the *reciprocal*
+ * of the hsync period in seconds.
+ */
+static inline void set_hsync_time(struct pxafb_info *fbi, unsigned int pcd)
+{
+ unsigned long htime;
+
+ if ((pcd == 0) || (fbi->fb.var.hsync_len == 0)) {
+ fbi->hsync_time = 0;
+ return;
+ }
+
+ htime = clk_get_rate(fbi->clk) / (pcd * fbi->fb.var.hsync_len);
+
+ fbi->hsync_time = htime;
+}
+
+unsigned long pxafb_get_hsync_time(struct device *dev)
+{
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
+
+ /* If display is blanked/suspended, hsync isn't active */
+ if (!fbi || (fbi->state != C_ENABLE))
+ return 0;
+
+ return fbi->hsync_time;
+}
+EXPORT_SYMBOL(pxafb_get_hsync_time);
+
+static int setup_frame_dma(struct pxafb_info *fbi, int dma, int pal,
+ unsigned long start, size_t size)
+{
+ struct pxafb_dma_descriptor *dma_desc, *pal_desc;
+ unsigned int dma_desc_off, pal_desc_off;
+
+ if (dma < 0 || dma >= DMA_MAX * 2)
+ return -EINVAL;
+
+ dma_desc = &fbi->dma_buff->dma_desc[dma];
+ dma_desc_off = offsetof(struct pxafb_dma_buff, dma_desc[dma]);
+
+ dma_desc->fsadr = start;
+ dma_desc->fidr = 0;
+ dma_desc->ldcmd = size;
+
+ if (pal < 0 || pal >= PAL_MAX * 2) {
+ dma_desc->fdadr = fbi->dma_buff_phys + dma_desc_off;
+ fbi->fdadr[dma] = fbi->dma_buff_phys + dma_desc_off;
+ } else {
+ pal_desc = &fbi->dma_buff->pal_desc[pal];
+ pal_desc_off = offsetof(struct pxafb_dma_buff, pal_desc[pal]);
+
+ pal_desc->fsadr = fbi->dma_buff_phys + pal * PALETTE_SIZE;
+ pal_desc->fidr = 0;
+
+ if ((fbi->lccr4 & LCCR4_PAL_FOR_MASK) == LCCR4_PAL_FOR_0)
+ pal_desc->ldcmd = fbi->palette_size * sizeof(u16);
+ else
+ pal_desc->ldcmd = fbi->palette_size * sizeof(u32);
+
+ pal_desc->ldcmd |= LDCMD_PAL;
+
+ /* flip back and forth between palette and frame buffer */
+ pal_desc->fdadr = fbi->dma_buff_phys + dma_desc_off;
+ dma_desc->fdadr = fbi->dma_buff_phys + pal_desc_off;
+ fbi->fdadr[dma] = fbi->dma_buff_phys + dma_desc_off;
+ }
+
+ return 0;
+}
+
+static void setup_base_frame(struct pxafb_info *fbi,
+ struct fb_var_screeninfo *var,
+ int branch)
+{
+ struct fb_fix_screeninfo *fix = &fbi->fb.fix;
+ int nbytes, dma, pal, bpp = var->bits_per_pixel;
+ unsigned long offset;
+
+ dma = DMA_BASE + (branch ? DMA_MAX : 0);
+ pal = (bpp >= 16) ? PAL_NONE : PAL_BASE + (branch ? PAL_MAX : 0);
+
+ nbytes = fix->line_length * var->yres;
+ offset = fix->line_length * var->yoffset + fbi->video_mem_phys;
+
+ if (fbi->lccr0 & LCCR0_SDS) {
+ nbytes = nbytes / 2;
+ setup_frame_dma(fbi, dma + 1, PAL_NONE, offset + nbytes, nbytes);
+ }
+
+ setup_frame_dma(fbi, dma, pal, offset, nbytes);
+}
+
+#ifdef CONFIG_FB_PXA_SMARTPANEL
+static int setup_smart_dma(struct pxafb_info *fbi)
+{
+ struct pxafb_dma_descriptor *dma_desc;
+ unsigned long dma_desc_off, cmd_buff_off;
+
+ dma_desc = &fbi->dma_buff->dma_desc[DMA_CMD];
+ dma_desc_off = offsetof(struct pxafb_dma_buff, dma_desc[DMA_CMD]);
+ cmd_buff_off = offsetof(struct pxafb_dma_buff, cmd_buff);
+
+ dma_desc->fdadr = fbi->dma_buff_phys + dma_desc_off;
+ dma_desc->fsadr = fbi->dma_buff_phys + cmd_buff_off;
+ dma_desc->fidr = 0;
+ dma_desc->ldcmd = fbi->n_smart_cmds * sizeof(uint16_t);
+
+ fbi->fdadr[DMA_CMD] = dma_desc->fdadr;
+ return 0;
+}
+
+int pxafb_smart_flush(struct fb_info *info)
+{
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+ uint32_t prsr;
+ int ret = 0;
+
+ /* disable controller until all registers are set up */
+ lcd_writel(fbi, LCCR0, fbi->reg_lccr0 & ~LCCR0_ENB);
+
+ /* 1. make it an even number of commands to align on 32-bit boundary
+ * 2. add the interrupt command to the end of the chain so we can
+ * keep track of the end of the transfer
+ */
+
+ while (fbi->n_smart_cmds & 1)
+ fbi->smart_cmds[fbi->n_smart_cmds++] = SMART_CMD_NOOP;
+
+ fbi->smart_cmds[fbi->n_smart_cmds++] = SMART_CMD_INTERRUPT;
+ fbi->smart_cmds[fbi->n_smart_cmds++] = SMART_CMD_WAIT_FOR_VSYNC;
+ setup_smart_dma(fbi);
+
+ /* continue to execute next command */
+ prsr = lcd_readl(fbi, PRSR) | PRSR_ST_OK | PRSR_CON_NT;
+ lcd_writel(fbi, PRSR, prsr);
+
+ /* stop the processor in case it executed "wait for sync" cmd */
+ lcd_writel(fbi, CMDCR, 0x0001);
+
+ /* don't send interrupts for fifo underruns on channel 6 */
+ lcd_writel(fbi, LCCR5, LCCR5_IUM(6));
+
+ lcd_writel(fbi, LCCR1, fbi->reg_lccr1);
+ lcd_writel(fbi, LCCR2, fbi->reg_lccr2);
+ lcd_writel(fbi, LCCR3, fbi->reg_lccr3);
+ lcd_writel(fbi, LCCR4, fbi->reg_lccr4);
+ lcd_writel(fbi, FDADR0, fbi->fdadr[0]);
+ lcd_writel(fbi, FDADR6, fbi->fdadr[6]);
+
+ /* begin sending */
+ lcd_writel(fbi, LCCR0, fbi->reg_lccr0 | LCCR0_ENB);
+
+ if (wait_for_completion_timeout(&fbi->command_done, HZ/2) == 0) {
+ pr_warning("%s: timeout waiting for command done\n",
+ __func__);
+ ret = -ETIMEDOUT;
+ }
+
+ /* quick disable */
+ prsr = lcd_readl(fbi, PRSR) & ~(PRSR_ST_OK | PRSR_CON_NT);
+ lcd_writel(fbi, PRSR, prsr);
+ lcd_writel(fbi, LCCR0, fbi->reg_lccr0 & ~LCCR0_ENB);
+ lcd_writel(fbi, FDADR6, 0);
+ fbi->n_smart_cmds = 0;
+ return ret;
+}
+
+int pxafb_smart_queue(struct fb_info *info, uint16_t *cmds, int n_cmds)
+{
+ int i;
+ struct pxafb_info *fbi = container_of(info, struct pxafb_info, fb);
+
+ for (i = 0; i < n_cmds; i++, cmds++) {
+ /* if it is a software delay, flush and delay */
+ if ((*cmds & 0xff00) == SMART_CMD_DELAY) {
+ pxafb_smart_flush(info);
+ mdelay(*cmds & 0xff);
+ continue;
+ }
+
+ /* leave 2 commands for INTERRUPT and WAIT_FOR_SYNC */
+ if (fbi->n_smart_cmds == CMD_BUFF_SIZE - 8)
+ pxafb_smart_flush(info);
+
+ fbi->smart_cmds[fbi->n_smart_cmds++] = *cmds;
+ }
+
+ return 0;
+}
+
+static unsigned int __smart_timing(unsigned time_ns, unsigned long lcd_clk)
+{
+ unsigned int t = (time_ns * (lcd_clk / 1000000) / 1000);
+ return (t == 0) ? 1 : t;
+}
+
+static void setup_smart_timing(struct pxafb_info *fbi,
+ struct fb_var_screeninfo *var)
+{
+ struct pxafb_mach_info *inf = dev_get_platdata(fbi->dev);
+ struct pxafb_mode_info *mode = &inf->modes[0];
+ unsigned long lclk = clk_get_rate(fbi->clk);
+ unsigned t1, t2, t3, t4;
+
+ t1 = max(mode->a0csrd_set_hld, mode->a0cswr_set_hld);
+ t2 = max(mode->rd_pulse_width, mode->wr_pulse_width);
+ t3 = mode->op_hold_time;
+ t4 = mode->cmd_inh_time;
+
+ fbi->reg_lccr1 =
+ LCCR1_DisWdth(var->xres) |
+ LCCR1_BegLnDel(__smart_timing(t1, lclk)) |
+ LCCR1_EndLnDel(__smart_timing(t2, lclk)) |
+ LCCR1_HorSnchWdth(__smart_timing(t3, lclk));
+
+ fbi->reg_lccr2 = LCCR2_DisHght(var->yres);
+ fbi->reg_lccr3 = fbi->lccr3 | LCCR3_PixClkDiv(__smart_timing(t4, lclk));
+ fbi->reg_lccr3 |= (var->sync & FB_SYNC_HOR_HIGH_ACT) ? LCCR3_HSP : 0;
+ fbi->reg_lccr3 |= (var->sync & FB_SYNC_VERT_HIGH_ACT) ? LCCR3_VSP : 0;
+
+ /* FIXME: make this configurable */
+ fbi->reg_cmdcr = 1;
+}
+
+static int pxafb_smart_thread(void *arg)
+{
+ struct pxafb_info *fbi = arg;
+ struct pxafb_mach_info *inf = dev_get_platdata(fbi->dev);
+
+ if (!inf->smart_update) {
+ pr_err("%s: not properly initialized, thread terminated\n",
+ __func__);
+ return -EINVAL;
+ }
+ inf = dev_get_platdata(fbi->dev);
+
+ pr_debug("%s(): task starting\n", __func__);
+
+ set_freezable();
+ while (!kthread_should_stop()) {
+
+ if (try_to_freeze())
+ continue;
+
+ mutex_lock(&fbi->ctrlr_lock);
+
+ if (fbi->state == C_ENABLE) {
+ inf->smart_update(&fbi->fb);
+ complete(&fbi->refresh_done);
+ }
+
+ mutex_unlock(&fbi->ctrlr_lock);
+
+ set_current_state(TASK_INTERRUPTIBLE);
+ schedule_timeout(msecs_to_jiffies(30));
+ }
+
+ pr_debug("%s(): task ending\n", __func__);
+ return 0;
+}
+
+static int pxafb_smart_init(struct pxafb_info *fbi)
+{
+ if (!(fbi->lccr0 & LCCR0_LCDT))
+ return 0;
+
+ fbi->smart_cmds = (uint16_t *) fbi->dma_buff->cmd_buff;
+ fbi->n_smart_cmds = 0;
+
+ init_completion(&fbi->command_done);
+ init_completion(&fbi->refresh_done);
+
+ fbi->smart_thread = kthread_run(pxafb_smart_thread, fbi,
+ "lcd_refresh");
+ if (IS_ERR(fbi->smart_thread)) {
+ pr_err("%s: unable to create kernel thread\n", __func__);
+ return PTR_ERR(fbi->smart_thread);
+ }
+
+ return 0;
+}
+#else
+static inline int pxafb_smart_init(struct pxafb_info *fbi) { return 0; }
+#endif /* CONFIG_FB_PXA_SMARTPANEL */
+
+static void setup_parallel_timing(struct pxafb_info *fbi,
+ struct fb_var_screeninfo *var)
+{
+ unsigned int lines_per_panel, pcd = get_pcd(fbi, var->pixclock);
+
+ fbi->reg_lccr1 =
+ LCCR1_DisWdth(var->xres) +
+ LCCR1_HorSnchWdth(var->hsync_len) +
+ LCCR1_BegLnDel(var->left_margin) +
+ LCCR1_EndLnDel(var->right_margin);
+
+ /*
+ * If we have a dual scan LCD, we need to halve
+ * the YRES parameter.
+ */
+ lines_per_panel = var->yres;
+ if ((fbi->lccr0 & LCCR0_SDS) == LCCR0_Dual)
+ lines_per_panel /= 2;
+
+ fbi->reg_lccr2 =
+ LCCR2_DisHght(lines_per_panel) +
+ LCCR2_VrtSnchWdth(var->vsync_len) +
+ LCCR2_BegFrmDel(var->upper_margin) +
+ LCCR2_EndFrmDel(var->lower_margin);
+
+ fbi->reg_lccr3 = fbi->lccr3 |
+ (var->sync & FB_SYNC_HOR_HIGH_ACT ?
+ LCCR3_HorSnchH : LCCR3_HorSnchL) |
+ (var->sync & FB_SYNC_VERT_HIGH_ACT ?
+ LCCR3_VrtSnchH : LCCR3_VrtSnchL);
+
+ if (pcd) {
+ fbi->reg_lccr3 |= LCCR3_PixClkDiv(pcd);
+ set_hsync_time(fbi, pcd);
+ }
+}
+
+/*
+ * pxafb_activate_var():
+ * Configures LCD Controller based on entries in var parameter.
+ * Settings are only written to the controller if changes were made.
+ */
+static int pxafb_activate_var(struct fb_var_screeninfo *var,
+ struct pxafb_info *fbi)
+{
+ u_long flags;
+
+ /* Update shadow copy atomically */
+ local_irq_save(flags);
+
+#ifdef CONFIG_FB_PXA_SMARTPANEL
+ if (fbi->lccr0 & LCCR0_LCDT)
+ setup_smart_timing(fbi, var);
+ else
+#endif
+ setup_parallel_timing(fbi, var);
+
+ setup_base_frame(fbi, var, 0);
+
+ fbi->reg_lccr0 = fbi->lccr0 |
+ (LCCR0_LDM | LCCR0_SFM | LCCR0_IUM | LCCR0_EFM |
+ LCCR0_QDM | LCCR0_BM | LCCR0_OUM);
+
+ fbi->reg_lccr3 |= pxafb_var_to_lccr3(var);
+
+ fbi->reg_lccr4 = lcd_readl(fbi, LCCR4) & ~LCCR4_PAL_FOR_MASK;
+ fbi->reg_lccr4 |= (fbi->lccr4 & LCCR4_PAL_FOR_MASK);
+ local_irq_restore(flags);
+
+ /*
+ * Only update the registers if the controller is enabled
+ * and something has changed.
+ */
+ if ((lcd_readl(fbi, LCCR0) != fbi->reg_lccr0) ||
+ (lcd_readl(fbi, LCCR1) != fbi->reg_lccr1) ||
+ (lcd_readl(fbi, LCCR2) != fbi->reg_lccr2) ||
+ (lcd_readl(fbi, LCCR3) != fbi->reg_lccr3) ||
+ (lcd_readl(fbi, LCCR4) != fbi->reg_lccr4) ||
+ (lcd_readl(fbi, FDADR0) != fbi->fdadr[0]) ||
+ ((fbi->lccr0 & LCCR0_SDS) &&
+ (lcd_readl(fbi, FDADR1) != fbi->fdadr[1])))
+ pxafb_schedule_work(fbi, C_REENABLE);
+
+ return 0;
+}
+
+/*
+ * NOTE! The following functions are purely helpers for set_ctrlr_state.
+ * Do not call them directly; set_ctrlr_state does the correct serialisation
+ * to ensure that things happen in the right way 100% of time time.
+ * -- rmk
+ */
+static inline void __pxafb_backlight_power(struct pxafb_info *fbi, int on)
+{
+ pr_debug("pxafb: backlight o%s\n", on ? "n" : "ff");
+
+ if (fbi->backlight_power)
+ fbi->backlight_power(on);
+}
+
+static inline void __pxafb_lcd_power(struct pxafb_info *fbi, int on)
+{
+ pr_debug("pxafb: LCD power o%s\n", on ? "n" : "ff");
+
+ if (fbi->lcd_power)
+ fbi->lcd_power(on, &fbi->fb.var);
+}
+
+static void pxafb_enable_controller(struct pxafb_info *fbi)
+{
+ pr_debug("pxafb: Enabling LCD controller\n");
+ pr_debug("fdadr0 0x%08x\n", (unsigned int) fbi->fdadr[0]);
+ pr_debug("fdadr1 0x%08x\n", (unsigned int) fbi->fdadr[1]);
+ pr_debug("reg_lccr0 0x%08x\n", (unsigned int) fbi->reg_lccr0);
+ pr_debug("reg_lccr1 0x%08x\n", (unsigned int) fbi->reg_lccr1);
+ pr_debug("reg_lccr2 0x%08x\n", (unsigned int) fbi->reg_lccr2);
+ pr_debug("reg_lccr3 0x%08x\n", (unsigned int) fbi->reg_lccr3);
+
+ /* enable LCD controller clock */
+ clk_prepare_enable(fbi->clk);
+
+ if (fbi->lccr0 & LCCR0_LCDT)
+ return;
+
+ /* Sequence from 11.7.10 */
+ lcd_writel(fbi, LCCR4, fbi->reg_lccr4);
+ lcd_writel(fbi, LCCR3, fbi->reg_lccr3);
+ lcd_writel(fbi, LCCR2, fbi->reg_lccr2);
+ lcd_writel(fbi, LCCR1, fbi->reg_lccr1);
+ lcd_writel(fbi, LCCR0, fbi->reg_lccr0 & ~LCCR0_ENB);
+
+ lcd_writel(fbi, FDADR0, fbi->fdadr[0]);
+ if (fbi->lccr0 & LCCR0_SDS)
+ lcd_writel(fbi, FDADR1, fbi->fdadr[1]);
+ lcd_writel(fbi, LCCR0, fbi->reg_lccr0 | LCCR0_ENB);
+}
+
+static void pxafb_disable_controller(struct pxafb_info *fbi)
+{
+ uint32_t lccr0;
+
+#ifdef CONFIG_FB_PXA_SMARTPANEL
+ if (fbi->lccr0 & LCCR0_LCDT) {
+ wait_for_completion_timeout(&fbi->refresh_done,
+ msecs_to_jiffies(200));
+ return;
+ }
+#endif
+
+ /* Clear LCD Status Register */
+ lcd_writel(fbi, LCSR, 0xffffffff);
+
+ lccr0 = lcd_readl(fbi, LCCR0) & ~LCCR0_LDM;
+ lcd_writel(fbi, LCCR0, lccr0);
+ lcd_writel(fbi, LCCR0, lccr0 | LCCR0_DIS);
+
+ wait_for_completion_timeout(&fbi->disable_done, msecs_to_jiffies(200));
+
+ /* disable LCD controller clock */
+ clk_disable_unprepare(fbi->clk);
+}
+
+/*
+ * pxafb_handle_irq: Handle 'LCD DONE' interrupts.
+ */
+static irqreturn_t pxafb_handle_irq(int irq, void *dev_id)
+{
+ struct pxafb_info *fbi = dev_id;
+ unsigned int lccr0, lcsr;
+
+ lcsr = lcd_readl(fbi, LCSR);
+ if (lcsr & LCSR_LDD) {
+ lccr0 = lcd_readl(fbi, LCCR0);
+ lcd_writel(fbi, LCCR0, lccr0 | LCCR0_LDM);
+ complete(&fbi->disable_done);
+ }
+
+#ifdef CONFIG_FB_PXA_SMARTPANEL
+ if (lcsr & LCSR_CMD_INT)
+ complete(&fbi->command_done);
+#endif
+ lcd_writel(fbi, LCSR, lcsr);
+
+#ifdef CONFIG_FB_PXA_OVERLAY
+ {
+ unsigned int lcsr1 = lcd_readl(fbi, LCSR1);
+ if (lcsr1 & LCSR1_BS(1))
+ complete(&fbi->overlay[0].branch_done);
+
+ if (lcsr1 & LCSR1_BS(2))
+ complete(&fbi->overlay[1].branch_done);
+
+ lcd_writel(fbi, LCSR1, lcsr1);
+ }
+#endif
+ return IRQ_HANDLED;
+}
+
+/*
+ * This function must be called from task context only, since it will
+ * sleep when disabling the LCD controller, or if we get two contending
+ * processes trying to alter state.
+ */
+static void set_ctrlr_state(struct pxafb_info *fbi, u_int state)
+{
+ u_int old_state;
+
+ mutex_lock(&fbi->ctrlr_lock);
+
+ old_state = fbi->state;
+
+ /*
+ * Hack around fbcon initialisation.
+ */
+ if (old_state == C_STARTUP && state == C_REENABLE)
+ state = C_ENABLE;
+
+ switch (state) {
+ case C_DISABLE_CLKCHANGE:
+ /*
+ * Disable controller for clock change. If the
+ * controller is already disabled, then do nothing.
+ */
+ if (old_state != C_DISABLE && old_state != C_DISABLE_PM) {
+ fbi->state = state;
+ /* TODO __pxafb_lcd_power(fbi, 0); */
+ pxafb_disable_controller(fbi);
+ }
+ break;
+
+ case C_DISABLE_PM:
+ case C_DISABLE:
+ /*
+ * Disable controller
+ */
+ if (old_state != C_DISABLE) {
+ fbi->state = state;
+ __pxafb_backlight_power(fbi, 0);
+ __pxafb_lcd_power(fbi, 0);
+ if (old_state != C_DISABLE_CLKCHANGE)
+ pxafb_disable_controller(fbi);
+ }
+ break;
+
+ case C_ENABLE_CLKCHANGE:
+ /*
+ * Enable the controller after clock change. Only
+ * do this if we were disabled for the clock change.
+ */
+ if (old_state == C_DISABLE_CLKCHANGE) {
+ fbi->state = C_ENABLE;
+ pxafb_enable_controller(fbi);
+ /* TODO __pxafb_lcd_power(fbi, 1); */
+ }
+ break;
+
+ case C_REENABLE:
+ /*
+ * Re-enable the controller only if it was already
+ * enabled. This is so we reprogram the control
+ * registers.
+ */
+ if (old_state == C_ENABLE) {
+ __pxafb_lcd_power(fbi, 0);
+ pxafb_disable_controller(fbi);
+ pxafb_enable_controller(fbi);
+ __pxafb_lcd_power(fbi, 1);
+ }
+ break;
+
+ case C_ENABLE_PM:
+ /*
+ * Re-enable the controller after PM. This is not
+ * perfect - think about the case where we were doing
+ * a clock change, and we suspended half-way through.
+ */
+ if (old_state != C_DISABLE_PM)
+ break;
+ /* fall through */
+
+ case C_ENABLE:
+ /*
+ * Power up the LCD screen, enable controller, and
+ * turn on the backlight.
+ */
+ if (old_state != C_ENABLE) {
+ fbi->state = C_ENABLE;
+ pxafb_enable_controller(fbi);
+ __pxafb_lcd_power(fbi, 1);
+ __pxafb_backlight_power(fbi, 1);
+ }
+ break;
+ }
+ mutex_unlock(&fbi->ctrlr_lock);
+}
+
+/*
+ * Our LCD controller task (which is called when we blank or unblank)
+ * via keventd.
+ */
+static void pxafb_task(struct work_struct *work)
+{
+ struct pxafb_info *fbi =
+ container_of(work, struct pxafb_info, task);
+ u_int state = xchg(&fbi->task_state, -1);
+
+ set_ctrlr_state(fbi, state);
+}
+
+#ifdef CONFIG_CPU_FREQ
+/*
+ * CPU clock speed change handler. We need to adjust the LCD timing
+ * parameters when the CPU clock is adjusted by the power management
+ * subsystem.
+ *
+ * TODO: Determine why f->new != 10*get_lclk_frequency_10khz()
+ */
+static int
+pxafb_freq_transition(struct notifier_block *nb, unsigned long val, void *data)
+{
+ struct pxafb_info *fbi = TO_INF(nb, freq_transition);
+ /* TODO struct cpufreq_freqs *f = data; */
+ u_int pcd;
+
+ switch (val) {
+ case CPUFREQ_PRECHANGE:
+#ifdef CONFIG_FB_PXA_OVERLAY
+ if (!(fbi->overlay[0].usage || fbi->overlay[1].usage))
+#endif
+ set_ctrlr_state(fbi, C_DISABLE_CLKCHANGE);
+ break;
+
+ case CPUFREQ_POSTCHANGE:
+ pcd = get_pcd(fbi, fbi->fb.var.pixclock);
+ set_hsync_time(fbi, pcd);
+ fbi->reg_lccr3 = (fbi->reg_lccr3 & ~0xff) |
+ LCCR3_PixClkDiv(pcd);
+ set_ctrlr_state(fbi, C_ENABLE_CLKCHANGE);
+ break;
+ }
+ return 0;
+}
+
+static int
+pxafb_freq_policy(struct notifier_block *nb, unsigned long val, void *data)
+{
+ struct pxafb_info *fbi = TO_INF(nb, freq_policy);
+ struct fb_var_screeninfo *var = &fbi->fb.var;
+ struct cpufreq_policy *policy = data;
+
+ switch (val) {
+ case CPUFREQ_ADJUST:
+ case CPUFREQ_INCOMPATIBLE:
+ pr_debug("min dma period: %d ps, "
+ "new clock %d kHz\n", pxafb_display_dma_period(var),
+ policy->max);
+ /* TODO: fill in min/max values */
+ break;
+ }
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_PM
+/*
+ * Power management hooks. Note that we won't be called from IRQ context,
+ * unlike the blank functions above, so we may sleep.
+ */
+static int pxafb_suspend(struct device *dev)
+{
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
+
+ set_ctrlr_state(fbi, C_DISABLE_PM);
+ return 0;
+}
+
+static int pxafb_resume(struct device *dev)
+{
+ struct pxafb_info *fbi = dev_get_drvdata(dev);
+
+ set_ctrlr_state(fbi, C_ENABLE_PM);
+ return 0;
+}
+
+static const struct dev_pm_ops pxafb_pm_ops = {
+ .suspend = pxafb_suspend,
+ .resume = pxafb_resume,
+};
+#endif
+
+static int pxafb_init_video_memory(struct pxafb_info *fbi)
+{
+ int size = PAGE_ALIGN(fbi->video_mem_size);
+
+ fbi->video_mem = alloc_pages_exact(size, GFP_KERNEL | __GFP_ZERO);
+ if (fbi->video_mem == NULL)
+ return -ENOMEM;
+
+ fbi->video_mem_phys = virt_to_phys(fbi->video_mem);
+ fbi->video_mem_size = size;
+
+ fbi->fb.fix.smem_start = fbi->video_mem_phys;
+ fbi->fb.fix.smem_len = fbi->video_mem_size;
+ fbi->fb.screen_base = fbi->video_mem;
+
+ return fbi->video_mem ? 0 : -ENOMEM;
+}
+
+static void pxafb_decode_mach_info(struct pxafb_info *fbi,
+ struct pxafb_mach_info *inf)
+{
+ unsigned int lcd_conn = inf->lcd_conn;
+ struct pxafb_mode_info *m;
+ int i;
+
+ fbi->cmap_inverse = inf->cmap_inverse;
+ fbi->cmap_static = inf->cmap_static;
+ fbi->lccr4 = inf->lccr4;
+
+ switch (lcd_conn & LCD_TYPE_MASK) {
+ case LCD_TYPE_MONO_STN:
+ fbi->lccr0 = LCCR0_CMS;
+ break;
+ case LCD_TYPE_MONO_DSTN:
+ fbi->lccr0 = LCCR0_CMS | LCCR0_SDS;
+ break;
+ case LCD_TYPE_COLOR_STN:
+ fbi->lccr0 = 0;
+ break;
+ case LCD_TYPE_COLOR_DSTN:
+ fbi->lccr0 = LCCR0_SDS;
+ break;
+ case LCD_TYPE_COLOR_TFT:
+ fbi->lccr0 = LCCR0_PAS;
+ break;
+ case LCD_TYPE_SMART_PANEL:
+ fbi->lccr0 = LCCR0_LCDT | LCCR0_PAS;
+ break;
+ default:
+ /* fall back to backward compatibility way */
+ fbi->lccr0 = inf->lccr0;
+ fbi->lccr3 = inf->lccr3;
+ goto decode_mode;
+ }
+
+ if (lcd_conn == LCD_MONO_STN_8BPP)
+ fbi->lccr0 |= LCCR0_DPD;
+
+ fbi->lccr0 |= (lcd_conn & LCD_ALTERNATE_MAPPING) ? LCCR0_LDDALT : 0;
+
+ fbi->lccr3 = LCCR3_Acb((inf->lcd_conn >> 10) & 0xff);
+ fbi->lccr3 |= (lcd_conn & LCD_BIAS_ACTIVE_LOW) ? LCCR3_OEP : 0;
+ fbi->lccr3 |= (lcd_conn & LCD_PCLK_EDGE_FALL) ? LCCR3_PCP : 0;
+
+decode_mode:
+ pxafb_setmode(&fbi->fb.var, &inf->modes[0]);
+
+ /* decide video memory size as follows:
+ * 1. default to mode of maximum resolution
+ * 2. allow platform to override
+ * 3. allow module parameter to override
+ */
+ for (i = 0, m = &inf->modes[0]; i < inf->num_modes; i++, m++)
+ fbi->video_mem_size = max_t(size_t, fbi->video_mem_size,
+ m->xres * m->yres * m->bpp / 8);
+
+ if (inf->video_mem_size > fbi->video_mem_size)
+ fbi->video_mem_size = inf->video_mem_size;
+
+ if (video_mem_size > fbi->video_mem_size)
+ fbi->video_mem_size = video_mem_size;
+}
+
+static struct pxafb_info *pxafb_init_fbinfo(struct device *dev)
+{
+ struct pxafb_info *fbi;
+ void *addr;
+ struct pxafb_mach_info *inf = dev_get_platdata(dev);
+
+ /* Alloc the pxafb_info and pseudo_palette in one step */
+ fbi = kmalloc(sizeof(struct pxafb_info) + sizeof(u32) * 16, GFP_KERNEL);
+ if (!fbi)
+ return NULL;
+
+ memset(fbi, 0, sizeof(struct pxafb_info));
+ fbi->dev = dev;
+
+ fbi->clk = clk_get(dev, NULL);
+ if (IS_ERR(fbi->clk)) {
+ kfree(fbi);
+ return NULL;
+ }
+
+ strcpy(fbi->fb.fix.id, PXA_NAME);
+
+ fbi->fb.fix.type = FB_TYPE_PACKED_PIXELS;
+ fbi->fb.fix.type_aux = 0;
+ fbi->fb.fix.xpanstep = 0;
+ fbi->fb.fix.ypanstep = 1;
+ fbi->fb.fix.ywrapstep = 0;
+ fbi->fb.fix.accel = FB_ACCEL_NONE;
+
+ fbi->fb.var.nonstd = 0;
+ fbi->fb.var.activate = FB_ACTIVATE_NOW;
+ fbi->fb.var.height = -1;
+ fbi->fb.var.width = -1;
+ fbi->fb.var.accel_flags = FB_ACCELF_TEXT;
+ fbi->fb.var.vmode = FB_VMODE_NONINTERLACED;
+
+ fbi->fb.fbops = &pxafb_ops;
+ fbi->fb.flags = FBINFO_DEFAULT;
+ fbi->fb.node = -1;
+
+ addr = fbi;
+ addr = addr + sizeof(struct pxafb_info);
+ fbi->fb.pseudo_palette = addr;
+
+ fbi->state = C_STARTUP;
+ fbi->task_state = (u_char)-1;
+
+ pxafb_decode_mach_info(fbi, inf);
+
+#ifdef CONFIG_FB_PXA_OVERLAY
+ /* place overlay(s) on top of base */
+ if (pxafb_overlay_supported())
+ fbi->lccr0 |= LCCR0_OUC;
+#endif
+
+ init_waitqueue_head(&fbi->ctrlr_wait);
+ INIT_WORK(&fbi->task, pxafb_task);
+ mutex_init(&fbi->ctrlr_lock);
+ init_completion(&fbi->disable_done);
+
+ return fbi;
+}
+
+#ifdef CONFIG_FB_PXA_PARAMETERS
+static int parse_opt_mode(struct device *dev, const char *this_opt)
+{
+ struct pxafb_mach_info *inf = dev_get_platdata(dev);
+
+ const char *name = this_opt+5;
+ unsigned int namelen = strlen(name);
+ int res_specified = 0, bpp_specified = 0;
+ unsigned int xres = 0, yres = 0, bpp = 0;
+ int yres_specified = 0;
+ int i;
+ for (i = namelen-1; i >= 0; i--) {
+ switch (name[i]) {
+ case '-':
+ namelen = i;
+ if (!bpp_specified && !yres_specified) {
+ bpp = simple_strtoul(&name[i+1], NULL, 0);
+ bpp_specified = 1;
+ } else
+ goto done;
+ break;
+ case 'x':
+ if (!yres_specified) {
+ yres = simple_strtoul(&name[i+1], NULL, 0);
+ yres_specified = 1;
+ } else
+ goto done;
+ break;
+ case '0' ... '9':
+ break;
+ default:
+ goto done;
+ }
+ }
+ if (i < 0 && yres_specified) {
+ xres = simple_strtoul(name, NULL, 0);
+ res_specified = 1;
+ }
+done:
+ if (res_specified) {
+ dev_info(dev, "overriding resolution: %dx%d\n", xres, yres);
+ inf->modes[0].xres = xres; inf->modes[0].yres = yres;
+ }
+ if (bpp_specified)
+ switch (bpp) {
+ case 1:
+ case 2:
+ case 4:
+ case 8:
+ case 16:
+ inf->modes[0].bpp = bpp;
+ dev_info(dev, "overriding bit depth: %d\n", bpp);
+ break;
+ default:
+ dev_err(dev, "Depth %d is not valid\n", bpp);
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int parse_opt(struct device *dev, char *this_opt)
+{
+ struct pxafb_mach_info *inf = dev_get_platdata(dev);
+ struct pxafb_mode_info *mode = &inf->modes[0];
+ char s[64];
+
+ s[0] = '\0';
+
+ if (!strncmp(this_opt, "vmem:", 5)) {
+ video_mem_size = memparse(this_opt + 5, NULL);
+ } else if (!strncmp(this_opt, "mode:", 5)) {
+ return parse_opt_mode(dev, this_opt);
+ } else if (!strncmp(this_opt, "pixclock:", 9)) {
+ mode->pixclock = simple_strtoul(this_opt+9, NULL, 0);
+ sprintf(s, "pixclock: %ld\n", mode->pixclock);
+ } else if (!strncmp(this_opt, "left:", 5)) {
+ mode->left_margin = simple_strtoul(this_opt+5, NULL, 0);
+ sprintf(s, "left: %u\n", mode->left_margin);
+ } else if (!strncmp(this_opt, "right:", 6)) {
+ mode->right_margin = simple_strtoul(this_opt+6, NULL, 0);
+ sprintf(s, "right: %u\n", mode->right_margin);
+ } else if (!strncmp(this_opt, "upper:", 6)) {
+ mode->upper_margin = simple_strtoul(this_opt+6, NULL, 0);
+ sprintf(s, "upper: %u\n", mode->upper_margin);
+ } else if (!strncmp(this_opt, "lower:", 6)) {
+ mode->lower_margin = simple_strtoul(this_opt+6, NULL, 0);
+ sprintf(s, "lower: %u\n", mode->lower_margin);
+ } else if (!strncmp(this_opt, "hsynclen:", 9)) {
+ mode->hsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ sprintf(s, "hsynclen: %u\n", mode->hsync_len);
+ } else if (!strncmp(this_opt, "vsynclen:", 9)) {
+ mode->vsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ sprintf(s, "vsynclen: %u\n", mode->vsync_len);
+ } else if (!strncmp(this_opt, "hsync:", 6)) {
+ if (simple_strtoul(this_opt+6, NULL, 0) == 0) {
+ sprintf(s, "hsync: Active Low\n");
+ mode->sync &= ~FB_SYNC_HOR_HIGH_ACT;
+ } else {
+ sprintf(s, "hsync: Active High\n");
+ mode->sync |= FB_SYNC_HOR_HIGH_ACT;
+ }
+ } else if (!strncmp(this_opt, "vsync:", 6)) {
+ if (simple_strtoul(this_opt+6, NULL, 0) == 0) {
+ sprintf(s, "vsync: Active Low\n");
+ mode->sync &= ~FB_SYNC_VERT_HIGH_ACT;
+ } else {
+ sprintf(s, "vsync: Active High\n");
+ mode->sync |= FB_SYNC_VERT_HIGH_ACT;
+ }
+ } else if (!strncmp(this_opt, "dpc:", 4)) {
+ if (simple_strtoul(this_opt+4, NULL, 0) == 0) {
+ sprintf(s, "double pixel clock: false\n");
+ inf->lccr3 &= ~LCCR3_DPC;
+ } else {
+ sprintf(s, "double pixel clock: true\n");
+ inf->lccr3 |= LCCR3_DPC;
+ }
+ } else if (!strncmp(this_opt, "outputen:", 9)) {
+ if (simple_strtoul(this_opt+9, NULL, 0) == 0) {
+ sprintf(s, "output enable: active low\n");
+ inf->lccr3 = (inf->lccr3 & ~LCCR3_OEP) | LCCR3_OutEnL;
+ } else {
+ sprintf(s, "output enable: active high\n");
+ inf->lccr3 = (inf->lccr3 & ~LCCR3_OEP) | LCCR3_OutEnH;
+ }
+ } else if (!strncmp(this_opt, "pixclockpol:", 12)) {
+ if (simple_strtoul(this_opt+12, NULL, 0) == 0) {
+ sprintf(s, "pixel clock polarity: falling edge\n");
+ inf->lccr3 = (inf->lccr3 & ~LCCR3_PCP) | LCCR3_PixFlEdg;
+ } else {
+ sprintf(s, "pixel clock polarity: rising edge\n");
+ inf->lccr3 = (inf->lccr3 & ~LCCR3_PCP) | LCCR3_PixRsEdg;
+ }
+ } else if (!strncmp(this_opt, "color", 5)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_CMS) | LCCR0_Color;
+ } else if (!strncmp(this_opt, "mono", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_CMS) | LCCR0_Mono;
+ } else if (!strncmp(this_opt, "active", 6)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_PAS) | LCCR0_Act;
+ } else if (!strncmp(this_opt, "passive", 7)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_PAS) | LCCR0_Pas;
+ } else if (!strncmp(this_opt, "single", 6)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_SDS) | LCCR0_Sngl;
+ } else if (!strncmp(this_opt, "dual", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_SDS) | LCCR0_Dual;
+ } else if (!strncmp(this_opt, "4pix", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_DPD) | LCCR0_4PixMono;
+ } else if (!strncmp(this_opt, "8pix", 4)) {
+ inf->lccr0 = (inf->lccr0 & ~LCCR0_DPD) | LCCR0_8PixMono;
+ } else {
+ dev_err(dev, "unknown option: %s\n", this_opt);
+ return -EINVAL;
+ }
+
+ if (s[0] != '\0')
+ dev_info(dev, "override %s", s);
+
+ return 0;
+}
+
+static int pxafb_parse_options(struct device *dev, char *options)
+{
+ char *this_opt;
+ int ret;
+
+ if (!options || !*options)
+ return 0;
+
+ dev_dbg(dev, "options are \"%s\"\n", options ? options : "null");
+
+ /* could be made table driven or similar?... */
+ while ((this_opt = strsep(&options, ",")) != NULL) {
+ ret = parse_opt(dev, this_opt);
+ if (ret)
+ return ret;
+ }
+ return 0;
+}
+
+static char g_options[256] = "";
+
+#ifndef MODULE
+static int __init pxafb_setup_options(void)
+{
+ char *options = NULL;
+
+ if (fb_get_options("pxafb", &options))
+ return -ENODEV;
+
+ if (options)
+ strlcpy(g_options, options, sizeof(g_options));
+
+ return 0;
+}
+#else
+#define pxafb_setup_options() (0)
+
+module_param_string(options, g_options, sizeof(g_options), 0);
+MODULE_PARM_DESC(options, "LCD parameters (see Documentation/fb/pxafb.txt)");
+#endif
+
+#else
+#define pxafb_parse_options(...) (0)
+#define pxafb_setup_options() (0)
+#endif
+
+#ifdef DEBUG_VAR
+/* Check for various illegal bit-combinations. Currently only
+ * a warning is given. */
+static void pxafb_check_options(struct device *dev, struct pxafb_mach_info *inf)
+{
+ if (inf->lcd_conn)
+ return;
+
+ if (inf->lccr0 & LCCR0_INVALID_CONFIG_MASK)
+ dev_warn(dev, "machine LCCR0 setting contains "
+ "illegal bits: %08x\n",
+ inf->lccr0 & LCCR0_INVALID_CONFIG_MASK);
+ if (inf->lccr3 & LCCR3_INVALID_CONFIG_MASK)
+ dev_warn(dev, "machine LCCR3 setting contains "
+ "illegal bits: %08x\n",
+ inf->lccr3 & LCCR3_INVALID_CONFIG_MASK);
+ if (inf->lccr0 & LCCR0_DPD &&
+ ((inf->lccr0 & LCCR0_PAS) != LCCR0_Pas ||
+ (inf->lccr0 & LCCR0_SDS) != LCCR0_Sngl ||
+ (inf->lccr0 & LCCR0_CMS) != LCCR0_Mono))
+ dev_warn(dev, "Double Pixel Data (DPD) mode is "
+ "only valid in passive mono"
+ " single panel mode\n");
+ if ((inf->lccr0 & LCCR0_PAS) == LCCR0_Act &&
+ (inf->lccr0 & LCCR0_SDS) == LCCR0_Dual)
+ dev_warn(dev, "Dual panel only valid in passive mode\n");
+ if ((inf->lccr0 & LCCR0_PAS) == LCCR0_Pas &&
+ (inf->modes->upper_margin || inf->modes->lower_margin))
+ dev_warn(dev, "Upper and lower margins must be 0 in "
+ "passive mode\n");
+}
+#else
+#define pxafb_check_options(...) do {} while (0)
+#endif
+
+static int pxafb_probe(struct platform_device *dev)
+{
+ struct pxafb_info *fbi;
+ struct pxafb_mach_info *inf;
+ struct resource *r;
+ int irq, ret;
+
+ dev_dbg(&dev->dev, "pxafb_probe\n");
+
+ inf = dev_get_platdata(&dev->dev);
+ ret = -ENOMEM;
+ fbi = NULL;
+ if (!inf)
+ goto failed;
+
+ ret = pxafb_parse_options(&dev->dev, g_options);
+ if (ret < 0)
+ goto failed;
+
+ pxafb_check_options(&dev->dev, inf);
+
+ dev_dbg(&dev->dev, "got a %dx%dx%d LCD\n",
+ inf->modes->xres,
+ inf->modes->yres,
+ inf->modes->bpp);
+ if (inf->modes->xres == 0 ||
+ inf->modes->yres == 0 ||
+ inf->modes->bpp == 0) {
+ dev_err(&dev->dev, "Invalid resolution or bit depth\n");
+ ret = -EINVAL;
+ goto failed;
+ }
+
+ fbi = pxafb_init_fbinfo(&dev->dev);
+ if (!fbi) {
+ /* only reason for pxafb_init_fbinfo to fail is kmalloc */
+ dev_err(&dev->dev, "Failed to initialize framebuffer device\n");
+ ret = -ENOMEM;
+ goto failed;
+ }
+
+ if (cpu_is_pxa3xx() && inf->acceleration_enabled)
+ fbi->fb.fix.accel = FB_ACCEL_PXA3XX;
+
+ fbi->backlight_power = inf->pxafb_backlight_power;
+ fbi->lcd_power = inf->pxafb_lcd_power;
+
+ r = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ dev_err(&dev->dev, "no I/O memory resource defined\n");
+ ret = -ENODEV;
+ goto failed_fbi;
+ }
+
+ r = request_mem_region(r->start, resource_size(r), dev->name);
+ if (r == NULL) {
+ dev_err(&dev->dev, "failed to request I/O memory\n");
+ ret = -EBUSY;
+ goto failed_fbi;
+ }
+
+ fbi->mmio_base = ioremap(r->start, resource_size(r));
+ if (fbi->mmio_base == NULL) {
+ dev_err(&dev->dev, "failed to map I/O memory\n");
+ ret = -EBUSY;
+ goto failed_free_res;
+ }
+
+ fbi->dma_buff_size = PAGE_ALIGN(sizeof(struct pxafb_dma_buff));
+ fbi->dma_buff = dma_alloc_coherent(fbi->dev, fbi->dma_buff_size,
+ &fbi->dma_buff_phys, GFP_KERNEL);
+ if (fbi->dma_buff == NULL) {
+ dev_err(&dev->dev, "failed to allocate memory for DMA\n");
+ ret = -ENOMEM;
+ goto failed_free_io;
+ }
+
+ ret = pxafb_init_video_memory(fbi);
+ if (ret) {
+ dev_err(&dev->dev, "Failed to allocate video RAM: %d\n", ret);
+ ret = -ENOMEM;
+ goto failed_free_dma;
+ }
+
+ irq = platform_get_irq(dev, 0);
+ if (irq < 0) {
+ dev_err(&dev->dev, "no IRQ defined\n");
+ ret = -ENODEV;
+ goto failed_free_mem;
+ }
+
+ ret = request_irq(irq, pxafb_handle_irq, 0, "LCD", fbi);
+ if (ret) {
+ dev_err(&dev->dev, "request_irq failed: %d\n", ret);
+ ret = -EBUSY;
+ goto failed_free_mem;
+ }
+
+ ret = pxafb_smart_init(fbi);
+ if (ret) {
+ dev_err(&dev->dev, "failed to initialize smartpanel\n");
+ goto failed_free_irq;
+ }
+
+ /*
+ * This makes sure that our colour bitfield
+ * descriptors are correctly initialised.
+ */
+ ret = pxafb_check_var(&fbi->fb.var, &fbi->fb);
+ if (ret) {
+ dev_err(&dev->dev, "failed to get suitable mode\n");
+ goto failed_free_irq;
+ }
+
+ ret = pxafb_set_par(&fbi->fb);
+ if (ret) {
+ dev_err(&dev->dev, "Failed to set parameters\n");
+ goto failed_free_irq;
+ }
+
+ platform_set_drvdata(dev, fbi);
+
+ ret = register_framebuffer(&fbi->fb);
+ if (ret < 0) {
+ dev_err(&dev->dev,
+ "Failed to register framebuffer device: %d\n", ret);
+ goto failed_free_cmap;
+ }
+
+ pxafb_overlay_init(fbi);
+
+#ifdef CONFIG_CPU_FREQ
+ fbi->freq_transition.notifier_call = pxafb_freq_transition;
+ fbi->freq_policy.notifier_call = pxafb_freq_policy;
+ cpufreq_register_notifier(&fbi->freq_transition,
+ CPUFREQ_TRANSITION_NOTIFIER);
+ cpufreq_register_notifier(&fbi->freq_policy,
+ CPUFREQ_POLICY_NOTIFIER);
+#endif
+
+ /*
+ * Ok, now enable the LCD controller
+ */
+ set_ctrlr_state(fbi, C_ENABLE);
+
+ return 0;
+
+failed_free_cmap:
+ if (fbi->fb.cmap.len)
+ fb_dealloc_cmap(&fbi->fb.cmap);
+failed_free_irq:
+ free_irq(irq, fbi);
+failed_free_mem:
+ free_pages_exact(fbi->video_mem, fbi->video_mem_size);
+failed_free_dma:
+ dma_free_coherent(&dev->dev, fbi->dma_buff_size,
+ fbi->dma_buff, fbi->dma_buff_phys);
+failed_free_io:
+ iounmap(fbi->mmio_base);
+failed_free_res:
+ release_mem_region(r->start, resource_size(r));
+failed_fbi:
+ clk_put(fbi->clk);
+ kfree(fbi);
+failed:
+ return ret;
+}
+
+static int pxafb_remove(struct platform_device *dev)
+{
+ struct pxafb_info *fbi = platform_get_drvdata(dev);
+ struct resource *r;
+ int irq;
+ struct fb_info *info;
+
+ if (!fbi)
+ return 0;
+
+ info = &fbi->fb;
+
+ pxafb_overlay_exit(fbi);
+ unregister_framebuffer(info);
+
+ pxafb_disable_controller(fbi);
+
+ if (fbi->fb.cmap.len)
+ fb_dealloc_cmap(&fbi->fb.cmap);
+
+ irq = platform_get_irq(dev, 0);
+ free_irq(irq, fbi);
+
+ free_pages_exact(fbi->video_mem, fbi->video_mem_size);
+
+ dma_free_writecombine(&dev->dev, fbi->dma_buff_size,
+ fbi->dma_buff, fbi->dma_buff_phys);
+
+ iounmap(fbi->mmio_base);
+
+ r = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ release_mem_region(r->start, resource_size(r));
+
+ clk_put(fbi->clk);
+ kfree(fbi);
+
+ return 0;
+}
+
+static struct platform_driver pxafb_driver = {
+ .probe = pxafb_probe,
+ .remove = pxafb_remove,
+ .driver = {
+ .name = "pxa2xx-fb",
+#ifdef CONFIG_PM
+ .pm = &pxafb_pm_ops,
+#endif
+ },
+};
+
+static int __init pxafb_init(void)
+{
+ if (pxafb_setup_options())
+ return -EINVAL;
+
+ return platform_driver_register(&pxafb_driver);
+}
+
+static void __exit pxafb_exit(void)
+{
+ platform_driver_unregister(&pxafb_driver);
+}
+
+module_init(pxafb_init);
+module_exit(pxafb_exit);
+
+MODULE_DESCRIPTION("loadable framebuffer driver for PXA");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff