--- /dev/null
+/*
+ * Wireless Host Controller (WHC) data structures.
+ *
+ * Copyright (C) 2007 Cambridge Silicon Radio Ltd.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version
+ * 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
+ * 02110-1301, USA.
+ */
+#ifndef _WHCI_WHCI_HC_H
+#define _WHCI_WHCI_HC_H
+
+#include <linux/list.h>
+
+/**
+ * WHCI_PAGE_SIZE - page size use by WHCI
+ *
+ * WHCI assumes that host system uses pages of 4096 octets.
+ */
+#define WHCI_PAGE_SIZE 4096
+
+
+/**
+ * QTD_MAX_TXFER_SIZE - max number of bytes to transfer with a single
+ * qtd.
+ *
+ * This is 2^20 - 1.
+ */
+#define QTD_MAX_XFER_SIZE 1048575
+
+
+/**
+ * struct whc_qtd - Queue Element Transfer Descriptors (qTD)
+ *
+ * This describes the data for a bulk, control or interrupt transfer.
+ *
+ * [WHCI] section 3.2.4
+ */
+struct whc_qtd {
+ __le32 status; /*< remaining transfer len and transfer status */
+ __le32 options;
+ __le64 page_list_ptr; /*< physical pointer to data buffer page list*/
+ __u8 setup[8]; /*< setup data for control transfers */
+} __attribute__((packed));
+
+#define QTD_STS_ACTIVE (1 << 31) /* enable execution of transaction */
+#define QTD_STS_HALTED (1 << 30) /* transfer halted */
+#define QTD_STS_DBE (1 << 29) /* data buffer error */
+#define QTD_STS_BABBLE (1 << 28) /* babble detected */
+#define QTD_STS_RCE (1 << 27) /* retry count exceeded */
+#define QTD_STS_LAST_PKT (1 << 26) /* set Last Packet Flag in WUSB header */
+#define QTD_STS_INACTIVE (1 << 25) /* queue set is marked inactive */
+#define QTD_STS_IALT_VALID (1 << 23) /* iAlt field is valid */
+#define QTD_STS_IALT(i) (QTD_STS_IALT_VALID | ((i) << 20)) /* iAlt field */
+#define QTD_STS_LEN(l) ((l) << 0) /* transfer length */
+#define QTD_STS_TO_LEN(s) ((s) & 0x000fffff)
+
+#define QTD_OPT_IOC (1 << 1) /* page_list_ptr points to buffer directly */
+#define QTD_OPT_SMALL (1 << 0) /* interrupt on complete */
+
+/**
+ * struct whc_itd - Isochronous Queue Element Transfer Descriptors (iTD)
+ *
+ * This describes the data and other parameters for an isochronous
+ * transfer.
+ *
+ * [WHCI] section 3.2.5
+ */
+struct whc_itd {
+ __le16 presentation_time; /*< presentation time for OUT transfers */
+ __u8 num_segments; /*< number of data segments in segment list */
+ __u8 status; /*< command execution status */
+ __le32 options; /*< misc transfer options */
+ __le64 page_list_ptr; /*< physical pointer to data buffer page list */
+ __le64 seg_list_ptr; /*< physical pointer to segment list */
+} __attribute__((packed));
+
+#define ITD_STS_ACTIVE (1 << 7) /* enable execution of transaction */
+#define ITD_STS_DBE (1 << 5) /* data buffer error */
+#define ITD_STS_BABBLE (1 << 4) /* babble detected */
+#define ITD_STS_INACTIVE (1 << 1) /* queue set is marked inactive */
+
+#define ITD_OPT_IOC (1 << 1) /* interrupt on complete */
+#define ITD_OPT_SMALL (1 << 0) /* page_list_ptr points to buffer directly */
+
+/**
+ * Page list entry.
+ *
+ * A TD's page list must contain sufficient page list entries for the
+ * total data length in the TD.
+ *
+ * [WHCI] section 3.2.4.3
+ */
+struct whc_page_list_entry {
+ __le64 buf_ptr; /*< physical pointer to buffer */
+} __attribute__((packed));
+
+/**
+ * struct whc_seg_list_entry - Segment list entry.
+ *
+ * Describes a portion of the data buffer described in the containing
+ * qTD's page list.
+ *
+ * seg_ptr = qtd->page_list_ptr[qtd->seg_list_ptr[seg].idx].buf_ptr
+ * + qtd->seg_list_ptr[seg].offset;
+ *
+ * Segments can't cross page boundries.
+ *
+ * [WHCI] section 3.2.5.5
+ */
+struct whc_seg_list_entry {
+ __le16 len; /*< segment length */
+ __u8 idx; /*< index into page list */
+ __u8 status; /*< segment status */
+ __le16 offset; /*< 12 bit offset into page */
+} __attribute__((packed));
+
+/**
+ * struct whc_qhead - endpoint and status information for a qset.
+ *
+ * [WHCI] section 3.2.6
+ */
+struct whc_qhead {
+ __le64 link; /*< next qset in list */
+ __le32 info1;
+ __le32 info2;
+ __le32 info3;
+ __le16 status;
+ __le16 err_count; /*< transaction error count */
+ __le32 cur_window;
+ __le32 scratch[3]; /*< h/w scratch area */
+ union {
+ struct whc_qtd qtd;
+ struct whc_itd itd;
+ } overlay;
+} __attribute__((packed));
+
+#define QH_LINK_PTR_MASK (~0x03Full)
+#define QH_LINK_PTR(ptr) ((ptr) & QH_LINK_PTR_MASK)
+#define QH_LINK_IQS (1 << 4) /* isochronous queue set */
+#define QH_LINK_NTDS(n) (((n) - 1) << 1) /* number of TDs in queue set */
+#define QH_LINK_T (1 << 0) /* last queue set in periodic schedule list */
+
+#define QH_INFO1_EP(e) ((e) << 0) /* endpoint number */
+#define QH_INFO1_DIR_IN (1 << 4) /* IN transfer */
+#define QH_INFO1_DIR_OUT (0 << 4) /* OUT transfer */
+#define QH_INFO1_TR_TYPE_CTRL (0x0 << 5) /* control transfer */
+#define QH_INFO1_TR_TYPE_ISOC (0x1 << 5) /* isochronous transfer */
+#define QH_INFO1_TR_TYPE_BULK (0x2 << 5) /* bulk transfer */
+#define QH_INFO1_TR_TYPE_INT (0x3 << 5) /* interrupt */
+#define QH_INFO1_TR_TYPE_LP_INT (0x7 << 5) /* low power interrupt */
+#define QH_INFO1_DEV_INFO_IDX(i) ((i) << 8) /* index into device info buffer */
+#define QH_INFO1_SET_INACTIVE (1 << 15) /* set inactive after transfer */
+#define QH_INFO1_MAX_PKT_LEN(l) ((l) << 16) /* maximum packet length */
+
+#define QH_INFO2_BURST(b) ((b) << 0) /* maximum burst length */
+#define QH_INFO2_DBP(p) ((p) << 5) /* data burst policy (see [WUSB] table 5-7) */
+#define QH_INFO2_MAX_COUNT(c) ((c) << 8) /* max isoc/int pkts per zone */
+#define QH_INFO2_RQS (1 << 15) /* reactivate queue set */
+#define QH_INFO2_MAX_RETRY(r) ((r) << 16) /* maximum transaction retries */
+#define QH_INFO2_MAX_SEQ(s) ((s) << 20) /* maximum sequence number */
+#define QH_INFO3_MAX_DELAY(d) ((d) << 0) /* maximum stream delay in 125 us units (isoc only) */
+#define QH_INFO3_INTERVAL(i) ((i) << 16) /* segment interval in 125 us units (isoc only) */
+
+#define QH_INFO3_TX_RATE(r) ((r) << 24) /* PHY rate (see [ECMA-368] section 10.3.1.1) */
+#define QH_INFO3_TX_PWR(p) ((p) << 29) /* transmit power (see [WUSB] section 5.2.1.2) */
+
+#define QH_STATUS_FLOW_CTRL (1 << 15)
+#define QH_STATUS_ICUR(i) ((i) << 5)
+#define QH_STATUS_TO_ICUR(s) (((s) >> 5) & 0x7)
+#define QH_STATUS_SEQ_MASK 0x1f
+
+/**
+ * usb_pipe_to_qh_type - USB core pipe type to QH transfer type
+ *
+ * Returns the QH type field for a USB core pipe type.
+ */
+static inline unsigned usb_pipe_to_qh_type(unsigned pipe)
+{
+ static const unsigned type[] = {
+ [PIPE_ISOCHRONOUS] = QH_INFO1_TR_TYPE_ISOC,
+ [PIPE_INTERRUPT] = QH_INFO1_TR_TYPE_INT,
+ [PIPE_CONTROL] = QH_INFO1_TR_TYPE_CTRL,
+ [PIPE_BULK] = QH_INFO1_TR_TYPE_BULK,
+ };
+ return type[usb_pipetype(pipe)];
+}
+
+/**
+ * Maxiumum number of TDs in a qset.
+ */
+#define WHCI_QSET_TD_MAX 8
+
+/**
+ * struct whc_qset - WUSB data transfers to a specific endpoint
+ * @qh: the QHead of this qset
+ * @qtd: up to 8 qTDs (for qsets for control, bulk and interrupt
+ * transfers)
+ * @itd: up to 8 iTDs (for qsets for isochronous transfers)
+ * @qset_dma: DMA address for this qset
+ * @whc: WHCI HC this qset is for
+ * @ep: endpoint
+ * @stds: list of sTDs queued to this qset
+ * @ntds: number of qTDs queued (not necessarily the same as nTDs
+ * field in the QH)
+ * @td_start: index of the first qTD in the list
+ * @td_end: index of next free qTD in the list (provided
+ * ntds < WHCI_QSET_TD_MAX)
+ *
+ * Queue Sets (qsets) are added to the asynchronous schedule list
+ * (ASL) or the periodic zone list (PZL).
+ *
+ * qsets may contain up to 8 TDs (either qTDs or iTDs as appropriate).
+ * Each TD may refer to at most 1 MiB of data. If a single transfer
+ * has > 8MiB of data, TDs can be reused as they are completed since
+ * the TD list is used as a circular buffer. Similarly, several
+ * (smaller) transfers may be queued in a qset.
+ *
+ * WHCI controllers may cache portions of the qsets in the ASL and
+ * PZL, requiring the WHCD to inform the WHC that the lists have been
+ * updated (fields changed or qsets inserted or removed). For safe
+ * insertion and removal of qsets from the lists the schedule must be
+ * stopped to avoid races in updating the QH link pointers.
+ *
+ * Since the HC is free to execute qsets in any order, all transfers
+ * to an endpoint should use the same qset to ensure transfers are
+ * executed in the order they're submitted.
+ *
+ * [WHCI] section 3.2.3
+ */
+struct whc_qset {
+ struct whc_qhead qh;
+ union {
+ struct whc_qtd qtd[WHCI_QSET_TD_MAX];
+ struct whc_itd itd[WHCI_QSET_TD_MAX];
+ };
+
+ /* private data for WHCD */
+ dma_addr_t qset_dma;
+ struct whc *whc;
+ struct usb_host_endpoint *ep;
+ struct list_head stds;
+ int ntds;
+ int td_start;
+ int td_end;
+ struct list_head list_node;
+ unsigned in_sw_list:1;
+ unsigned in_hw_list:1;
+ unsigned remove:1;
+ unsigned reset:1;
+ struct urb *pause_after_urb;
+ struct completion remove_complete;
+ uint16_t max_packet;
+ uint8_t max_burst;
+ uint8_t max_seq;
+};
+
+static inline void whc_qset_set_link_ptr(u64 *ptr, u64 target)
+{
+ if (target)
+ *ptr = (*ptr & ~(QH_LINK_PTR_MASK | QH_LINK_T)) | QH_LINK_PTR(target);
+ else
+ *ptr = QH_LINK_T;
+}
+
+/**
+ * struct di_buf_entry - Device Information (DI) buffer entry.
+ *
+ * There's one of these per connected device.
+ */
+struct di_buf_entry {
+ __le32 availability_info[8]; /*< MAS availability information, one MAS per bit */
+ __le32 addr_sec_info; /*< addressing and security info */
+ __le32 reserved[7];
+} __attribute__((packed));
+
+#define WHC_DI_SECURE (1 << 31)
+#define WHC_DI_DISABLE (1 << 30)
+#define WHC_DI_KEY_IDX(k) ((k) << 8)
+#define WHC_DI_KEY_IDX_MASK 0x0000ff00
+#define WHC_DI_DEV_ADDR(a) ((a) << 0)
+#define WHC_DI_DEV_ADDR_MASK 0x000000ff
+
+/**
+ * struct dn_buf_entry - Device Notification (DN) buffer entry.
+ *
+ * [WHCI] section 3.2.8
+ */
+struct dn_buf_entry {
+ __u8 msg_size; /*< number of octets of valid DN data */
+ __u8 reserved1;
+ __u8 src_addr; /*< source address */
+ __u8 status; /*< buffer entry status */
+ __le32 tkid; /*< TKID for source device, valid if secure bit is set */
+ __u8 dn_data[56]; /*< up to 56 octets of DN data */
+} __attribute__((packed));
+
+#define WHC_DN_STATUS_VALID (1 << 7) /* buffer entry is valid */
+#define WHC_DN_STATUS_SECURE (1 << 6) /* notification received using secure frame */
+
+#define WHC_N_DN_ENTRIES (4096 / sizeof(struct dn_buf_entry))
+
+/* The Add MMC IE WUSB Generic Command may take up to 256 bytes of
+ data. [WHCI] section 2.4.7. */
+#define WHC_GEN_CMD_DATA_LEN 256
+
+/*
+ * HC registers.
+ *
+ * [WHCI] section 2.4
+ */
+
+#define WHCIVERSION 0x00
+
+#define WHCSPARAMS 0x04
+# define WHCSPARAMS_TO_N_MMC_IES(p) (((p) >> 16) & 0xff)
+# define WHCSPARAMS_TO_N_KEYS(p) (((p) >> 8) & 0xff)
+# define WHCSPARAMS_TO_N_DEVICES(p) (((p) >> 0) & 0x7f)
+
+#define WUSBCMD 0x08
+# define WUSBCMD_BCID(b) ((b) << 16)
+# define WUSBCMD_BCID_MASK (0xff << 16)
+# define WUSBCMD_ASYNC_QSET_RM (1 << 12)
+# define WUSBCMD_PERIODIC_QSET_RM (1 << 11)
+# define WUSBCMD_WUSBSI(s) ((s) << 8)
+# define WUSBCMD_WUSBSI_MASK (0x7 << 8)
+# define WUSBCMD_ASYNC_SYNCED_DB (1 << 7)
+# define WUSBCMD_PERIODIC_SYNCED_DB (1 << 6)
+# define WUSBCMD_ASYNC_UPDATED (1 << 5)
+# define WUSBCMD_PERIODIC_UPDATED (1 << 4)
+# define WUSBCMD_ASYNC_EN (1 << 3)
+# define WUSBCMD_PERIODIC_EN (1 << 2)
+# define WUSBCMD_WHCRESET (1 << 1)
+# define WUSBCMD_RUN (1 << 0)
+
+#define WUSBSTS 0x0c
+# define WUSBSTS_ASYNC_SCHED (1 << 15)
+# define WUSBSTS_PERIODIC_SCHED (1 << 14)
+# define WUSBSTS_DNTS_SCHED (1 << 13)
+# define WUSBSTS_HCHALTED (1 << 12)
+# define WUSBSTS_GEN_CMD_DONE (1 << 9)
+# define WUSBSTS_CHAN_TIME_ROLLOVER (1 << 8)
+# define WUSBSTS_DNTS_OVERFLOW (1 << 7)
+# define WUSBSTS_BPST_ADJUSTMENT_CHANGED (1 << 6)
+# define WUSBSTS_HOST_ERR (1 << 5)
+# define WUSBSTS_ASYNC_SCHED_SYNCED (1 << 4)
+# define WUSBSTS_PERIODIC_SCHED_SYNCED (1 << 3)
+# define WUSBSTS_DNTS_INT (1 << 2)
+# define WUSBSTS_ERR_INT (1 << 1)
+# define WUSBSTS_INT (1 << 0)
+# define WUSBSTS_INT_MASK 0x3ff
+
+#define WUSBINTR 0x10
+# define WUSBINTR_GEN_CMD_DONE (1 << 9)
+# define WUSBINTR_CHAN_TIME_ROLLOVER (1 << 8)
+# define WUSBINTR_DNTS_OVERFLOW (1 << 7)
+# define WUSBINTR_BPST_ADJUSTMENT_CHANGED (1 << 6)
+# define WUSBINTR_HOST_ERR (1 << 5)
+# define WUSBINTR_ASYNC_SCHED_SYNCED (1 << 4)
+# define WUSBINTR_PERIODIC_SCHED_SYNCED (1 << 3)
+# define WUSBINTR_DNTS_INT (1 << 2)
+# define WUSBINTR_ERR_INT (1 << 1)
+# define WUSBINTR_INT (1 << 0)
+# define WUSBINTR_ALL 0x3ff
+
+#define WUSBGENCMDSTS 0x14
+# define WUSBGENCMDSTS_ACTIVE (1 << 31)
+# define WUSBGENCMDSTS_ERROR (1 << 24)
+# define WUSBGENCMDSTS_IOC (1 << 23)
+# define WUSBGENCMDSTS_MMCIE_ADD 0x01
+# define WUSBGENCMDSTS_MMCIE_RM 0x02
+# define WUSBGENCMDSTS_SET_MAS 0x03
+# define WUSBGENCMDSTS_CHAN_STOP 0x04
+# define WUSBGENCMDSTS_RWP_EN 0x05
+
+#define WUSBGENCMDPARAMS 0x18
+#define WUSBGENADDR 0x20
+#define WUSBASYNCLISTADDR 0x28
+#define WUSBDNTSBUFADDR 0x30
+#define WUSBDEVICEINFOADDR 0x38
+
+#define WUSBSETSECKEYCMD 0x40
+# define WUSBSETSECKEYCMD_SET (1 << 31)
+# define WUSBSETSECKEYCMD_ERASE (1 << 30)
+# define WUSBSETSECKEYCMD_GTK (1 << 8)
+# define WUSBSETSECKEYCMD_IDX(i) ((i) << 0)
+
+#define WUSBTKID 0x44
+#define WUSBSECKEY 0x48
+#define WUSBPERIODICLISTBASE 0x58
+#define WUSBMASINDEX 0x60
+
+#define WUSBDNTSCTRL 0x64
+# define WUSBDNTSCTRL_ACTIVE (1 << 31)
+# define WUSBDNTSCTRL_INTERVAL(i) ((i) << 8)
+# define WUSBDNTSCTRL_SLOTS(s) ((s) << 0)
+
+#define WUSBTIME 0x68
+# define WUSBTIME_CHANNEL_TIME_MASK 0x00ffffff
+
+#define WUSBBPST 0x6c
+#define WUSBDIBUPDATED 0x70
+
+#endif /* #ifndef _WHCI_WHCI_HC_H */
Code Review / kvmfornfv.git / blobdiff