--- /dev/null
+/*
+ * Host interface registers
+ */
+
+#define OXU_DEVICEID 0x00
+ #define OXU_REV_MASK 0xffff0000
+ #define OXU_REV_SHIFT 16
+ #define OXU_REV_2100 0x2100
+ #define OXU_BO_SHIFT 8
+ #define OXU_BO_MASK (0x3 << OXU_BO_SHIFT)
+ #define OXU_MAJ_REV_SHIFT 4
+ #define OXU_MAJ_REV_MASK (0xf << OXU_MAJ_REV_SHIFT)
+ #define OXU_MIN_REV_SHIFT 0
+ #define OXU_MIN_REV_MASK (0xf << OXU_MIN_REV_SHIFT)
+#define OXU_HOSTIFCONFIG 0x04
+#define OXU_SOFTRESET 0x08
+ #define OXU_SRESET (1 << 0)
+
+#define OXU_PIOBURSTREADCTRL 0x0C
+
+#define OXU_CHIPIRQSTATUS 0x10
+#define OXU_CHIPIRQEN_SET 0x14
+#define OXU_CHIPIRQEN_CLR 0x18
+ #define OXU_USBSPHLPWUI 0x00000080
+ #define OXU_USBOTGLPWUI 0x00000040
+ #define OXU_USBSPHI 0x00000002
+ #define OXU_USBOTGI 0x00000001
+
+#define OXU_CLKCTRL_SET 0x1C
+ #define OXU_SYSCLKEN 0x00000008
+ #define OXU_USBSPHCLKEN 0x00000002
+ #define OXU_USBOTGCLKEN 0x00000001
+
+#define OXU_ASO 0x68
+ #define OXU_SPHPOEN 0x00000100
+ #define OXU_OVRCCURPUPDEN 0x00000800
+ #define OXU_ASO_OP (1 << 10)
+ #define OXU_COMPARATOR 0x000004000
+
+#define OXU_USBMODE 0x1A8
+ #define OXU_VBPS 0x00000020
+ #define OXU_ES_LITTLE 0x00000000
+ #define OXU_CM_HOST_ONLY 0x00000003
+
+/*
+ * Proper EHCI structs & defines
+ */
+
+/* Magic numbers that can affect system performance */
+#define EHCI_TUNE_CERR 3 /* 0-3 qtd retries; 0 == don't stop */
+#define EHCI_TUNE_RL_HS 4 /* nak throttle; see 4.9 */
+#define EHCI_TUNE_RL_TT 0
+#define EHCI_TUNE_MULT_HS 1 /* 1-3 transactions/uframe; 4.10.3 */
+#define EHCI_TUNE_MULT_TT 1
+#define EHCI_TUNE_FLS 2 /* (small) 256 frame schedule */
+
+struct oxu_hcd;
+
+/* EHCI register interface, corresponds to EHCI Revision 0.95 specification */
+
+/* Section 2.2 Host Controller Capability Registers */
+struct ehci_caps {
+ /* these fields are specified as 8 and 16 bit registers,
+ * but some hosts can't perform 8 or 16 bit PCI accesses.
+ */
+ u32 hc_capbase;
+#define HC_LENGTH(p) (((p)>>00)&0x00ff) /* bits 7:0 */
+#define HC_VERSION(p) (((p)>>16)&0xffff) /* bits 31:16 */
+ u32 hcs_params; /* HCSPARAMS - offset 0x4 */
+#define HCS_DEBUG_PORT(p) (((p)>>20)&0xf) /* bits 23:20, debug port? */
+#define HCS_INDICATOR(p) ((p)&(1 << 16)) /* true: has port indicators */
+#define HCS_N_CC(p) (((p)>>12)&0xf) /* bits 15:12, #companion HCs */
+#define HCS_N_PCC(p) (((p)>>8)&0xf) /* bits 11:8, ports per CC */
+#define HCS_PORTROUTED(p) ((p)&(1 << 7)) /* true: port routing */
+#define HCS_PPC(p) ((p)&(1 << 4)) /* true: port power control */
+#define HCS_N_PORTS(p) (((p)>>0)&0xf) /* bits 3:0, ports on HC */
+
+ u32 hcc_params; /* HCCPARAMS - offset 0x8 */
+#define HCC_EXT_CAPS(p) (((p)>>8)&0xff) /* for pci extended caps */
+#define HCC_ISOC_CACHE(p) ((p)&(1 << 7)) /* true: can cache isoc frame */
+#define HCC_ISOC_THRES(p) (((p)>>4)&0x7) /* bits 6:4, uframes cached */
+#define HCC_CANPARK(p) ((p)&(1 << 2)) /* true: can park on async qh */
+#define HCC_PGM_FRAMELISTLEN(p) ((p)&(1 << 1)) /* true: periodic_size changes*/
+#define HCC_64BIT_ADDR(p) ((p)&(1)) /* true: can use 64-bit addr */
+ u8 portroute[8]; /* nibbles for routing - offset 0xC */
+} __attribute__ ((packed));
+
+
+/* Section 2.3 Host Controller Operational Registers */
+struct ehci_regs {
+ /* USBCMD: offset 0x00 */
+ u32 command;
+/* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */
+#define CMD_PARK (1<<11) /* enable "park" on async qh */
+#define CMD_PARK_CNT(c) (((c)>>8)&3) /* how many transfers to park for */
+#define CMD_LRESET (1<<7) /* partial reset (no ports, etc) */
+#define CMD_IAAD (1<<6) /* "doorbell" interrupt async advance */
+#define CMD_ASE (1<<5) /* async schedule enable */
+#define CMD_PSE (1<<4) /* periodic schedule enable */
+/* 3:2 is periodic frame list size */
+#define CMD_RESET (1<<1) /* reset HC not bus */
+#define CMD_RUN (1<<0) /* start/stop HC */
+
+ /* USBSTS: offset 0x04 */
+ u32 status;
+#define STS_ASS (1<<15) /* Async Schedule Status */
+#define STS_PSS (1<<14) /* Periodic Schedule Status */
+#define STS_RECL (1<<13) /* Reclamation */
+#define STS_HALT (1<<12) /* Not running (any reason) */
+/* some bits reserved */
+ /* these STS_* flags are also intr_enable bits (USBINTR) */
+#define STS_IAA (1<<5) /* Interrupted on async advance */
+#define STS_FATAL (1<<4) /* such as some PCI access errors */
+#define STS_FLR (1<<3) /* frame list rolled over */
+#define STS_PCD (1<<2) /* port change detect */
+#define STS_ERR (1<<1) /* "error" completion (overflow, ...) */
+#define STS_INT (1<<0) /* "normal" completion (short, ...) */
+
+#define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
+
+ /* USBINTR: offset 0x08 */
+ u32 intr_enable;
+
+ /* FRINDEX: offset 0x0C */
+ u32 frame_index; /* current microframe number */
+ /* CTRLDSSEGMENT: offset 0x10 */
+ u32 segment; /* address bits 63:32 if needed */
+ /* PERIODICLISTBASE: offset 0x14 */
+ u32 frame_list; /* points to periodic list */
+ /* ASYNCLISTADDR: offset 0x18 */
+ u32 async_next; /* address of next async queue head */
+
+ u32 reserved[9];
+
+ /* CONFIGFLAG: offset 0x40 */
+ u32 configured_flag;
+#define FLAG_CF (1<<0) /* true: we'll support "high speed" */
+
+ /* PORTSC: offset 0x44 */
+ u32 port_status[0]; /* up to N_PORTS */
+/* 31:23 reserved */
+#define PORT_WKOC_E (1<<22) /* wake on overcurrent (enable) */
+#define PORT_WKDISC_E (1<<21) /* wake on disconnect (enable) */
+#define PORT_WKCONN_E (1<<20) /* wake on connect (enable) */
+/* 19:16 for port testing */
+#define PORT_LED_OFF (0<<14)
+#define PORT_LED_AMBER (1<<14)
+#define PORT_LED_GREEN (2<<14)
+#define PORT_LED_MASK (3<<14)
+#define PORT_OWNER (1<<13) /* true: companion hc owns this port */
+#define PORT_POWER (1<<12) /* true: has power (see PPC) */
+#define PORT_USB11(x) (((x)&(3<<10)) == (1<<10)) /* USB 1.1 device */
+/* 11:10 for detecting lowspeed devices (reset vs release ownership) */
+/* 9 reserved */
+#define PORT_RESET (1<<8) /* reset port */
+#define PORT_SUSPEND (1<<7) /* suspend port */
+#define PORT_RESUME (1<<6) /* resume it */
+#define PORT_OCC (1<<5) /* over current change */
+#define PORT_OC (1<<4) /* over current active */
+#define PORT_PEC (1<<3) /* port enable change */
+#define PORT_PE (1<<2) /* port enable */
+#define PORT_CSC (1<<1) /* connect status change */
+#define PORT_CONNECT (1<<0) /* device connected */
+#define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)
+} __attribute__ ((packed));
+
+/* Appendix C, Debug port ... intended for use with special "debug devices"
+ * that can help if there's no serial console. (nonstandard enumeration.)
+ */
+struct ehci_dbg_port {
+ u32 control;
+#define DBGP_OWNER (1<<30)
+#define DBGP_ENABLED (1<<28)
+#define DBGP_DONE (1<<16)
+#define DBGP_INUSE (1<<10)
+#define DBGP_ERRCODE(x) (((x)>>7)&0x07)
+# define DBGP_ERR_BAD 1
+# define DBGP_ERR_SIGNAL 2
+#define DBGP_ERROR (1<<6)
+#define DBGP_GO (1<<5)
+#define DBGP_OUT (1<<4)
+#define DBGP_LEN(x) (((x)>>0)&0x0f)
+ u32 pids;
+#define DBGP_PID_GET(x) (((x)>>16)&0xff)
+#define DBGP_PID_SET(data, tok) (((data)<<8)|(tok))
+ u32 data03;
+ u32 data47;
+ u32 address;
+#define DBGP_EPADDR(dev, ep) (((dev)<<8)|(ep))
+} __attribute__ ((packed));
+
+
+#define QTD_NEXT(dma) cpu_to_le32((u32)dma)
+
+/*
+ * EHCI Specification 0.95 Section 3.5
+ * QTD: describe data transfer components (buffer, direction, ...)
+ * See Fig 3-6 "Queue Element Transfer Descriptor Block Diagram".
+ *
+ * These are associated only with "QH" (Queue Head) structures,
+ * used with control, bulk, and interrupt transfers.
+ */
+struct ehci_qtd {
+ /* first part defined by EHCI spec */
+ __le32 hw_next; /* see EHCI 3.5.1 */
+ __le32 hw_alt_next; /* see EHCI 3.5.2 */
+ __le32 hw_token; /* see EHCI 3.5.3 */
+#define QTD_TOGGLE (1 << 31) /* data toggle */
+#define QTD_LENGTH(tok) (((tok)>>16) & 0x7fff)
+#define QTD_IOC (1 << 15) /* interrupt on complete */
+#define QTD_CERR(tok) (((tok)>>10) & 0x3)
+#define QTD_PID(tok) (((tok)>>8) & 0x3)
+#define QTD_STS_ACTIVE (1 << 7) /* HC may execute this */
+#define QTD_STS_HALT (1 << 6) /* halted on error */
+#define QTD_STS_DBE (1 << 5) /* data buffer error (in HC) */
+#define QTD_STS_BABBLE (1 << 4) /* device was babbling (qtd halted) */
+#define QTD_STS_XACT (1 << 3) /* device gave illegal response */
+#define QTD_STS_MMF (1 << 2) /* incomplete split transaction */
+#define QTD_STS_STS (1 << 1) /* split transaction state */
+#define QTD_STS_PING (1 << 0) /* issue PING? */
+ __le32 hw_buf[5]; /* see EHCI 3.5.4 */
+ __le32 hw_buf_hi[5]; /* Appendix B */
+
+ /* the rest is HCD-private */
+ dma_addr_t qtd_dma; /* qtd address */
+ struct list_head qtd_list; /* sw qtd list */
+ struct urb *urb; /* qtd's urb */
+ size_t length; /* length of buffer */
+
+ u32 qtd_buffer_len;
+ void *buffer;
+ dma_addr_t buffer_dma;
+ void *transfer_buffer;
+ void *transfer_dma;
+} __attribute__ ((aligned(32)));
+
+/* mask NakCnt+T in qh->hw_alt_next */
+#define QTD_MASK cpu_to_le32 (~0x1f)
+
+#define IS_SHORT_READ(token) (QTD_LENGTH(token) != 0 && QTD_PID(token) == 1)
+
+/* Type tag from {qh, itd, sitd, fstn}->hw_next */
+#define Q_NEXT_TYPE(dma) ((dma) & cpu_to_le32 (3 << 1))
+
+/* values for that type tag */
+#define Q_TYPE_QH cpu_to_le32 (1 << 1)
+
+/* next async queue entry, or pointer to interrupt/periodic QH */
+#define QH_NEXT(dma) (cpu_to_le32(((u32)dma)&~0x01f)|Q_TYPE_QH)
+
+/* for periodic/async schedules and qtd lists, mark end of list */
+#define EHCI_LIST_END cpu_to_le32(1) /* "null pointer" to hw */
+
+/*
+ * Entries in periodic shadow table are pointers to one of four kinds
+ * of data structure. That's dictated by the hardware; a type tag is
+ * encoded in the low bits of the hardware's periodic schedule. Use
+ * Q_NEXT_TYPE to get the tag.
+ *
+ * For entries in the async schedule, the type tag always says "qh".
+ */
+union ehci_shadow {
+ struct ehci_qh *qh; /* Q_TYPE_QH */
+ __le32 *hw_next; /* (all types) */
+ void *ptr;
+};
+
+/*
+ * EHCI Specification 0.95 Section 3.6
+ * QH: describes control/bulk/interrupt endpoints
+ * See Fig 3-7 "Queue Head Structure Layout".
+ *
+ * These appear in both the async and (for interrupt) periodic schedules.
+ */
+
+struct ehci_qh {
+ /* first part defined by EHCI spec */
+ __le32 hw_next; /* see EHCI 3.6.1 */
+ __le32 hw_info1; /* see EHCI 3.6.2 */
+#define QH_HEAD 0x00008000
+ __le32 hw_info2; /* see EHCI 3.6.2 */
+#define QH_SMASK 0x000000ff
+#define QH_CMASK 0x0000ff00
+#define QH_HUBADDR 0x007f0000
+#define QH_HUBPORT 0x3f800000
+#define QH_MULT 0xc0000000
+ __le32 hw_current; /* qtd list - see EHCI 3.6.4 */
+
+ /* qtd overlay (hardware parts of a struct ehci_qtd) */
+ __le32 hw_qtd_next;
+ __le32 hw_alt_next;
+ __le32 hw_token;
+ __le32 hw_buf[5];
+ __le32 hw_buf_hi[5];
+
+ /* the rest is HCD-private */
+ dma_addr_t qh_dma; /* address of qh */
+ union ehci_shadow qh_next; /* ptr to qh; or periodic */
+ struct list_head qtd_list; /* sw qtd list */
+ struct ehci_qtd *dummy;
+ struct ehci_qh *reclaim; /* next to reclaim */
+
+ struct oxu_hcd *oxu;
+ struct kref kref;
+ unsigned stamp;
+
+ u8 qh_state;
+#define QH_STATE_LINKED 1 /* HC sees this */
+#define QH_STATE_UNLINK 2 /* HC may still see this */
+#define QH_STATE_IDLE 3 /* HC doesn't see this */
+#define QH_STATE_UNLINK_WAIT 4 /* LINKED and on reclaim q */
+#define QH_STATE_COMPLETING 5 /* don't touch token.HALT */
+
+ /* periodic schedule info */
+ u8 usecs; /* intr bandwidth */
+ u8 gap_uf; /* uframes split/csplit gap */
+ u8 c_usecs; /* ... split completion bw */
+ u16 tt_usecs; /* tt downstream bandwidth */
+ unsigned short period; /* polling interval */
+ unsigned short start; /* where polling starts */
+#define NO_FRAME ((unsigned short)~0) /* pick new start */
+ struct usb_device *dev; /* access to TT */
+} __attribute__ ((aligned(32)));
+
+/*
+ * Proper OXU210HP structs
+ */
+
+#define OXU_OTG_CORE_OFFSET 0x00400
+#define OXU_OTG_CAP_OFFSET (OXU_OTG_CORE_OFFSET + 0x100)
+#define OXU_SPH_CORE_OFFSET 0x00800
+#define OXU_SPH_CAP_OFFSET (OXU_SPH_CORE_OFFSET + 0x100)
+
+#define OXU_OTG_MEM 0xE000
+#define OXU_SPH_MEM 0x16000
+
+/* Only how many elements & element structure are specifies here. */
+/* 2 host controllers are enabled - total size <= 28 kbytes */
+#define DEFAULT_I_TDPS 1024
+#define QHEAD_NUM 16
+#define QTD_NUM 32
+#define SITD_NUM 8
+#define MURB_NUM 8
+
+#define BUFFER_NUM 8
+#define BUFFER_SIZE 512
+
+struct oxu_info {
+ struct usb_hcd *hcd[2];
+};
+
+struct oxu_buf {
+ u8 buffer[BUFFER_SIZE];
+} __attribute__ ((aligned(BUFFER_SIZE)));
+
+struct oxu_onchip_mem {
+ struct oxu_buf db_pool[BUFFER_NUM];
+
+ u32 frame_list[DEFAULT_I_TDPS];
+ struct ehci_qh qh_pool[QHEAD_NUM];
+ struct ehci_qtd qtd_pool[QTD_NUM];
+} __attribute__ ((aligned(4 << 10)));
+
+#define EHCI_MAX_ROOT_PORTS 15 /* see HCS_N_PORTS */
+
+struct oxu_murb {
+ struct urb urb;
+ struct urb *main;
+ u8 last;
+};
+
+struct oxu_hcd { /* one per controller */
+ unsigned int is_otg:1;
+
+ u8 qh_used[QHEAD_NUM];
+ u8 qtd_used[QTD_NUM];
+ u8 db_used[BUFFER_NUM];
+ u8 murb_used[MURB_NUM];
+
+ struct oxu_onchip_mem __iomem *mem;
+ spinlock_t mem_lock;
+
+ struct timer_list urb_timer;
+
+ struct ehci_caps __iomem *caps;
+ struct ehci_regs __iomem *regs;
+
+ __u32 hcs_params; /* cached register copy */
+ spinlock_t lock;
+
+ /* async schedule support */
+ struct ehci_qh *async;
+ struct ehci_qh *reclaim;
+ unsigned reclaim_ready:1;
+ unsigned scanning:1;
+
+ /* periodic schedule support */
+ unsigned periodic_size;
+ __le32 *periodic; /* hw periodic table */
+ dma_addr_t periodic_dma;
+ unsigned i_thresh; /* uframes HC might cache */
+
+ union ehci_shadow *pshadow; /* mirror hw periodic table */
+ int next_uframe; /* scan periodic, start here */
+ unsigned periodic_sched; /* periodic activity count */
+
+ /* per root hub port */
+ unsigned long reset_done[EHCI_MAX_ROOT_PORTS];
+ /* bit vectors (one bit per port) */
+ unsigned long bus_suspended; /* which ports were
+ * already suspended at the
+ * start of a bus suspend
+ */
+ unsigned long companion_ports;/* which ports are dedicated
+ * to the companion controller
+ */
+
+ struct timer_list watchdog;
+ unsigned long actions;
+ unsigned stamp;
+ unsigned long next_statechange;
+ u32 command;
+
+ /* SILICON QUIRKS */
+ struct list_head urb_list; /* this is the head to urb
+ * queue that didn't get enough
+ * resources
+ */
+ struct oxu_murb *murb_pool; /* murb per split big urb */
+ unsigned urb_len;
+
+ u8 sbrn; /* packed release number */
+};
+
+#define EHCI_IAA_JIFFIES (HZ/100) /* arbitrary; ~10 msec */
+#define EHCI_IO_JIFFIES (HZ/10) /* io watchdog > irq_thresh */
+#define EHCI_ASYNC_JIFFIES (HZ/20) /* async idle timeout */
+#define EHCI_SHRINK_JIFFIES (HZ/200) /* async qh unlink delay */
+
+enum ehci_timer_action {
+ TIMER_IO_WATCHDOG,
+ TIMER_IAA_WATCHDOG,
+ TIMER_ASYNC_SHRINK,
+ TIMER_ASYNC_OFF,
+};
+
+#include <linux/oxu210hp.h>
Code Review / kvmfornfv.git / blobdiff