--- /dev/null
+#
+# USB Host Controller Drivers
+#
+comment "USB Host Controller Drivers"
+
+config USB_C67X00_HCD
+ tristate "Cypress C67x00 HCD support"
+ help
+ The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
+ host/peripheral/OTG USB controllers.
+
+ Enable this option to support this chip in host controller mode.
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called c67x00.
+
+config USB_XHCI_HCD
+ tristate "xHCI HCD (USB 3.0) support"
+ ---help---
+ The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
+ "SuperSpeed" host controller hardware.
+
+ To compile this driver as a module, choose M here: the
+ module will be called xhci-hcd.
+
+if USB_XHCI_HCD
+
+config USB_XHCI_PCI
+ tristate
+ depends on PCI
+ default y
+
+config USB_XHCI_PLATFORM
+ tristate
+
+config USB_XHCI_MVEBU
+ tristate "xHCI support for Marvell Armada 375/38x"
+ select USB_XHCI_PLATFORM
+ depends on ARCH_MVEBU || COMPILE_TEST
+ ---help---
+ Say 'Y' to enable the support for the xHCI host controller
+ found in Marvell Armada 375/38x ARM SOCs.
+
+config USB_XHCI_RCAR
+ tristate "xHCI support for Renesas R-Car SoCs"
+ select USB_XHCI_PLATFORM
+ depends on ARCH_SHMOBILE || COMPILE_TEST
+ ---help---
+ Say 'Y' to enable the support for the xHCI host controller
+ found in Renesas R-Car ARM SoCs.
+
+endif # USB_XHCI_HCD
+
+config USB_EHCI_HCD
+ tristate "EHCI HCD (USB 2.0) support"
+ ---help---
+ The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
+ "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
+ If your USB host controller supports USB 2.0, you will likely want to
+ configure this Host Controller Driver.
+
+ EHCI controllers are packaged with "companion" host controllers (OHCI
+ or UHCI) to handle USB 1.1 devices connected to root hub ports. Ports
+ will connect to EHCI if the device is high speed, otherwise they
+ connect to a companion controller. If you configure EHCI, you should
+ probably configure the OHCI (for NEC and some other vendors) USB Host
+ Controller Driver or UHCI (for Via motherboards) Host Controller
+ Driver too.
+
+ You may want to read <file:Documentation/usb/ehci.txt>.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ehci-hcd.
+
+config USB_EHCI_ROOT_HUB_TT
+ bool "Root Hub Transaction Translators"
+ depends on USB_EHCI_HCD
+ ---help---
+ Some EHCI chips have vendor-specific extensions to integrate
+ transaction translators, so that no OHCI or UHCI companion
+ controller is needed. It's safe to say "y" even if your
+ controller doesn't support this feature.
+
+ This supports the EHCI implementation that's originally
+ from ARC, and has since changed hands a few times.
+
+config USB_EHCI_TT_NEWSCHED
+ bool "Improved Transaction Translator scheduling"
+ depends on USB_EHCI_HCD
+ default y
+ ---help---
+ This changes the periodic scheduling code to fill more of the low
+ and full speed bandwidth available from the Transaction Translator
+ (TT) in USB 2.0 hubs. Without this, only one transfer will be
+ issued in each microframe, significantly reducing the number of
+ periodic low/fullspeed transfers possible.
+
+ If you have multiple periodic low/fullspeed devices connected to a
+ highspeed USB hub which is connected to a highspeed USB Host
+ Controller, and some of those devices will not work correctly
+ (possibly due to "ENOSPC" or "-28" errors), say Y. Conversely, if
+ you have only one such device and it doesn't work, you could try
+ saying N.
+
+ If unsure, say Y.
+
+config USB_FSL_MPH_DR_OF
+ tristate
+
+if USB_EHCI_HCD
+
+config USB_EHCI_PCI
+ tristate
+ depends on PCI
+ default y
+
+config USB_EHCI_HCD_PMC_MSP
+ tristate "EHCI support for on-chip PMC MSP71xx USB controller"
+ depends on MSP_HAS_USB
+ default n
+ select USB_EHCI_BIG_ENDIAN_DESC
+ select USB_EHCI_BIG_ENDIAN_MMIO
+ ---help---
+ Enables support for the onchip USB controller on the PMC_MSP7100 Family SoC's.
+ If unsure, say N.
+
+config XPS_USB_HCD_XILINX
+ bool "Use Xilinx usb host EHCI controller core"
+ depends on (PPC32 || MICROBLAZE)
+ select USB_EHCI_BIG_ENDIAN_DESC
+ select USB_EHCI_BIG_ENDIAN_MMIO
+ ---help---
+ Xilinx xps USB host controller core is EHCI compliant and has
+ transaction translator built-in. It can be configured to either
+ support both high speed and full speed devices, or high speed
+ devices only.
+
+config USB_EHCI_FSL
+ bool "Support for Freescale PPC on-chip EHCI USB controller"
+ depends on FSL_SOC
+ select USB_EHCI_ROOT_HUB_TT
+ select USB_FSL_MPH_DR_OF if OF
+ ---help---
+ Variation of ARC USB block used in some Freescale chips.
+
+config USB_EHCI_MXC
+ tristate "Support for Freescale i.MX on-chip EHCI USB controller"
+ depends on ARCH_MXC
+ select USB_EHCI_ROOT_HUB_TT
+ ---help---
+ Variation of ARC USB block used in some Freescale chips.
+
+config USB_EHCI_HCD_OMAP
+ tristate "EHCI support for OMAP3 and later chips"
+ depends on ARCH_OMAP
+ select NOP_USB_XCEIV
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on
+ OMAP3 and later chips.
+
+config USB_EHCI_HCD_ORION
+ tristate "Support for Marvell EBU on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && PLAT_ORION
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on Marvell's
+ embedded ARM SoCs, including Orion, Kirkwood, Dove, Armada XP,
+ Armada 370. This is different from the EHCI implementation
+ on Marvell's mobile PXA and MMP SoC, see "EHCI support for
+ Marvell PXA/MMP USB controller" for those.
+
+config USB_EHCI_HCD_SPEAR
+ tristate "Support for ST SPEAr on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && PLAT_SPEAR
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on
+ ST SPEAr chips.
+
+config USB_EHCI_HCD_STI
+ tristate "Support for ST STiHxxx on-chip EHCI USB controller"
+ depends on ARCH_STI && OF
+ select GENERIC_PHY
+ select USB_EHCI_HCD_PLATFORM
+ help
+ Enable support for the on-chip EHCI controller found on
+ STMicroelectronics consumer electronics SoC's.
+
+config USB_EHCI_HCD_AT91
+ tristate "Support for Atmel on-chip EHCI USB controller"
+ depends on USB_EHCI_HCD && ARCH_AT91
+ default y
+ ---help---
+ Enables support for the on-chip EHCI controller on
+ Atmel chips.
+
+config USB_EHCI_MSM
+ tristate "Support for Qualcomm QSD/MSM on-chip EHCI USB controller"
+ depends on ARCH_QCOM
+ select USB_EHCI_ROOT_HUB_TT
+ ---help---
+ Enables support for the USB Host controller present on the
+ Qualcomm chipsets. Root Hub has inbuilt TT.
+ This driver depends on OTG driver for PHY initialization,
+ clock management, powering up VBUS, and power management.
+ This driver is not supported on boards like trout which
+ has an external PHY.
+
+config USB_EHCI_TEGRA
+ tristate "NVIDIA Tegra HCD support"
+ depends on ARCH_TEGRA
+ select USB_EHCI_ROOT_HUB_TT
+ select USB_PHY
+ help
+ This driver enables support for the internal USB Host Controllers
+ found in NVIDIA Tegra SoCs. The controllers are EHCI compliant.
+
+config USB_EHCI_HCD_PPC_OF
+ bool "EHCI support for PPC USB controller on OF platform bus"
+ depends on PPC
+ default y
+ ---help---
+ Enables support for the USB controller present on the PowerPC
+ OpenFirmware platform bus.
+
+config USB_EHCI_SH
+ bool "EHCI support for SuperH USB controller"
+ depends on SUPERH
+ ---help---
+ Enables support for the on-chip EHCI controller on the SuperH.
+ If you use the PCI EHCI controller, this option is not necessary.
+
+config USB_EHCI_EXYNOS
+ tristate "EHCI support for Samsung S5P/EXYNOS SoC Series"
+ depends on ARCH_S5PV210 || ARCH_EXYNOS
+ help
+ Enable support for the Samsung Exynos SOC's on-chip EHCI controller.
+
+config USB_EHCI_MV
+ bool "EHCI support for Marvell PXA/MMP USB controller"
+ depends on (ARCH_PXA || ARCH_MMP)
+ select USB_EHCI_ROOT_HUB_TT
+ ---help---
+ Enables support for Marvell (including PXA and MMP series) on-chip
+ USB SPH and OTG controller. SPH is a single port host, and it can
+ only be EHCI host. OTG is controller that can switch to host mode.
+ Note that this driver will not work on Marvell's other EHCI
+ controller used by the EBU-type SoCs including Orion, Kirkwood,
+ Dova, Armada 370 and Armada XP. See "Support for Marvell EBU
+ on-chip EHCI USB controller" for those.
+
+config USB_W90X900_EHCI
+ tristate "W90X900(W90P910) EHCI support"
+ depends on ARCH_W90X900
+ ---help---
+ Enables support for the W90X900 USB controller
+
+config USB_CNS3XXX_EHCI
+ bool "Cavium CNS3XXX EHCI Module (DEPRECATED)"
+ depends on ARCH_CNS3XXX
+ select USB_EHCI_HCD_PLATFORM
+ ---help---
+ This option is deprecated now and the driver was removed, use
+ USB_EHCI_HCD_PLATFORM instead.
+
+ Enable support for the CNS3XXX SOC's on-chip EHCI controller.
+ It is needed for high-speed (480Mbit/sec) USB 2.0 device
+ support.
+
+config USB_EHCI_ATH79
+ bool "EHCI support for AR7XXX/AR9XXX SoCs (DEPRECATED)"
+ depends on (SOC_AR71XX || SOC_AR724X || SOC_AR913X || SOC_AR933X)
+ select USB_EHCI_ROOT_HUB_TT
+ select USB_EHCI_HCD_PLATFORM
+ default y
+ ---help---
+ This option is deprecated now and the driver was removed, use
+ USB_EHCI_HCD_PLATFORM instead.
+
+ Enables support for the built-in EHCI controller present
+ on the Atheros AR7XXX/AR9XXX SoCs.
+
+config USB_EHCI_HCD_PLATFORM
+ tristate "Generic EHCI driver for a platform device"
+ default n
+ ---help---
+ Adds an EHCI host driver for a generic platform device, which
+ provides a memory space and an irq.
+
+ If unsure, say N.
+
+config USB_OCTEON_EHCI
+ bool "Octeon on-chip EHCI support (DEPRECATED)"
+ depends on CAVIUM_OCTEON_SOC
+ default n
+ select USB_EHCI_BIG_ENDIAN_MMIO
+ select USB_EHCI_HCD_PLATFORM
+ help
+ This option is deprecated now and the driver was removed, use
+ USB_EHCI_HCD_PLATFORM instead.
+
+ Enable support for the Octeon II SOC's on-chip EHCI
+ controller. It is needed for high-speed (480Mbit/sec)
+ USB 2.0 device support. All CN6XXX based chips with USB are
+ supported.
+
+endif # USB_EHCI_HCD
+
+config USB_OXU210HP_HCD
+ tristate "OXU210HP HCD support"
+ ---help---
+ The OXU210HP is an USB host/OTG/device controller. Enable this
+ option if your board has this chip. If unsure, say N.
+
+ This driver does not support isochronous transfers and doesn't
+ implement OTG nor USB device controllers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called oxu210hp-hcd.
+
+config USB_ISP116X_HCD
+ tristate "ISP116X HCD support"
+ ---help---
+ The ISP1160 and ISP1161 chips are USB host controllers. Enable this
+ option if your board has this chip. If unsure, say N.
+
+ This driver does not support isochronous transfers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called isp116x-hcd.
+
+config USB_ISP1362_HCD
+ tristate "ISP1362 HCD support"
+ ---help---
+ Supports the Philips ISP1362 chip as a host controller
+
+ This driver does not support isochronous transfers.
+
+ To compile this driver as a module, choose M here: the
+ module will be called isp1362-hcd.
+
+config USB_FUSBH200_HCD
+ tristate "FUSBH200 HCD support"
+ depends on USB
+ ---help---
+ Faraday FUSBH200 is designed to meet USB2.0 EHCI specification
+ with minor modification.
+
+ To compile this driver as a module, choose M here: the
+ module will be called fusbh200-hcd.
+
+config USB_FOTG210_HCD
+ tristate "FOTG210 HCD support"
+ depends on USB
+ ---help---
+ Faraday FOTG210 is an OTG controller which can be configured as
+ an USB2.0 host. It is designed to meet USB2.0 EHCI specification
+ with minor modification.
+
+ To compile this driver as a module, choose M here: the
+ module will be called fotg210-hcd.
+
+config USB_MAX3421_HCD
+ tristate "MAX3421 HCD (USB-over-SPI) support"
+ depends on USB && SPI
+ ---help---
+ The Maxim MAX3421E chip supports standard USB 2.0-compliant
+ full-speed devices either in host or peripheral mode. This
+ driver supports the host-mode of the MAX3421E only.
+
+ To compile this driver as a module, choose M here: the module will
+ be called max3421-hcd.
+
+config USB_OHCI_HCD
+ tristate "OHCI HCD (USB 1.1) support"
+ ---help---
+ The Open Host Controller Interface (OHCI) is a standard for accessing
+ USB 1.1 host controller hardware. It does more in hardware than Intel's
+ UHCI specification. If your USB host controller follows the OHCI spec,
+ say Y. On most non-x86 systems, and on x86 hardware that's not using a
+ USB controller from Intel or VIA, this is appropriate. If your host
+ controller doesn't use PCI, this is probably appropriate. For a PCI
+ based system where you're not sure, the "lspci -v" entry will list the
+ right "prog-if" for your USB controller(s): EHCI, OHCI, or UHCI.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ohci-hcd.
+
+if USB_OHCI_HCD
+
+config USB_OHCI_HCD_OMAP1
+ tristate "OHCI support for OMAP1/2 chips"
+ depends on ARCH_OMAP1
+ depends on ISP1301_OMAP || !(MACH_OMAP_H2 || MACH_OMAP_H3)
+ default y
+ ---help---
+ Enables support for the OHCI controller on OMAP1/2 chips.
+
+config USB_OHCI_HCD_SPEAR
+ tristate "Support for ST SPEAr on-chip OHCI USB controller"
+ depends on USB_OHCI_HCD && PLAT_SPEAR
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ ST SPEAr chips.
+
+config USB_OHCI_HCD_STI
+ tristate "Support for ST STiHxxx on-chip OHCI USB controller"
+ depends on ARCH_STI && OF
+ select GENERIC_PHY
+ select USB_OHCI_HCD_PLATFORM
+ help
+ Enable support for the on-chip OHCI controller found on
+ STMicroelectronics consumer electronics SoC's.
+
+config USB_OHCI_HCD_S3C2410
+ tristate "OHCI support for Samsung S3C24xx/S3C64xx SoC series"
+ depends on USB_OHCI_HCD && (ARCH_S3C24XX || ARCH_S3C64XX)
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ S3C24xx/S3C64xx chips.
+
+config USB_OHCI_HCD_LPC32XX
+ tristate "Support for LPC on-chip OHCI USB controller"
+ depends on USB_OHCI_HCD && ARCH_LPC32XX
+ depends on USB_ISP1301
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ NXP chips.
+
+config USB_OHCI_HCD_PXA27X
+ tristate "Support for PXA27X/PXA3XX on-chip OHCI USB controller"
+ depends on USB_OHCI_HCD && (PXA27x || PXA3xx)
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ PXA27x/PXA3xx chips.
+
+config USB_OHCI_HCD_AT91
+ tristate "Support for Atmel on-chip OHCI USB controller"
+ depends on USB_OHCI_HCD && ARCH_AT91
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ Atmel chips.
+
+config USB_OHCI_HCD_OMAP3
+ tristate "OHCI support for OMAP3 and later chips"
+ depends on (ARCH_OMAP3 || ARCH_OMAP4)
+ default y
+ ---help---
+ Enables support for the on-chip OHCI controller on
+ OMAP3 and later chips.
+
+config USB_OHCI_HCD_DAVINCI
+ bool "OHCI support for TI DaVinci DA8xx"
+ depends on ARCH_DAVINCI_DA8XX
+ depends on USB_OHCI_HCD=y
+ default y
+ help
+ Enables support for the DaVinci DA8xx integrated OHCI
+ controller. This driver cannot currently be a loadable
+ module because it lacks a proper PHY abstraction.
+
+config USB_OHCI_ATH79
+ bool "USB OHCI support for the Atheros AR71XX/AR7240 SoCs (DEPRECATED)"
+ depends on (SOC_AR71XX || SOC_AR724X)
+ select USB_OHCI_HCD_PLATFORM
+ default y
+ help
+ This option is deprecated now and the driver was removed, use
+ USB_OHCI_HCD_PLATFORM instead.
+
+ Enables support for the built-in OHCI controller present on the
+ Atheros AR71XX/AR7240 SoCs.
+
+config USB_OHCI_HCD_PPC_OF_BE
+ bool "OHCI support for OF platform bus (big endian)"
+ depends on PPC
+ select USB_OHCI_BIG_ENDIAN_DESC
+ select USB_OHCI_BIG_ENDIAN_MMIO
+ ---help---
+ Enables support for big-endian USB controllers present on the
+ OpenFirmware platform bus.
+
+config USB_OHCI_HCD_PPC_OF_LE
+ bool "OHCI support for OF platform bus (little endian)"
+ depends on PPC
+ select USB_OHCI_LITTLE_ENDIAN
+ ---help---
+ Enables support for little-endian USB controllers present on the
+ OpenFirmware platform bus.
+
+config USB_OHCI_HCD_PPC_OF
+ bool
+ depends on PPC
+ default USB_OHCI_HCD_PPC_OF_BE || USB_OHCI_HCD_PPC_OF_LE
+
+config USB_OHCI_HCD_PCI
+ tristate "OHCI support for PCI-bus USB controllers"
+ depends on PCI
+ default y
+ select USB_OHCI_LITTLE_ENDIAN
+ ---help---
+ Enables support for PCI-bus plug-in USB controller cards.
+ If unsure, say Y.
+
+config USB_OHCI_HCD_SSB
+ bool "OHCI support for Broadcom SSB OHCI core (DEPRECATED)"
+ depends on (SSB = y || SSB = USB_OHCI_HCD)
+ select USB_HCD_SSB
+ select USB_OHCI_HCD_PLATFORM
+ default n
+ ---help---
+ This option is deprecated now and the driver was removed, use
+ USB_HCD_SSB and USB_OHCI_HCD_PLATFORM instead.
+
+ Support for the Sonics Silicon Backplane (SSB) attached
+ Broadcom USB OHCI core.
+
+ This device is present in some embedded devices with
+ Broadcom based SSB bus.
+
+ If unsure, say N.
+
+config USB_OHCI_SH
+ bool "OHCI support for SuperH USB controller (DEPRECATED)"
+ depends on SUPERH
+ select USB_OHCI_HCD_PLATFORM
+ ---help---
+ This option is deprecated now and the driver was removed, use
+ USB_OHCI_HCD_PLATFORM instead.
+
+ Enables support for the on-chip OHCI controller on the SuperH.
+ If you use the PCI OHCI controller, this option is not necessary.
+
+config USB_OHCI_EXYNOS
+ tristate "OHCI support for Samsung S5P/EXYNOS SoC Series"
+ depends on ARCH_S5PV210 || ARCH_EXYNOS
+ help
+ Enable support for the Samsung Exynos SOC's on-chip OHCI controller.
+
+config USB_CNS3XXX_OHCI
+ bool "Cavium CNS3XXX OHCI Module (DEPRECATED)"
+ depends on ARCH_CNS3XXX
+ select USB_OHCI_HCD_PLATFORM
+ ---help---
+ This option is deprecated now and the driver was removed, use
+ USB_OHCI_HCD_PLATFORM instead.
+
+ Enable support for the CNS3XXX SOC's on-chip OHCI controller.
+ It is needed for low-speed USB 1.0 device support.
+
+config USB_OHCI_HCD_PLATFORM
+ tristate "Generic OHCI driver for a platform device"
+ default n
+ ---help---
+ Adds an OHCI host driver for a generic platform device, which
+ provides a memory space and an irq.
+
+ If unsure, say N.
+
+config USB_OCTEON_OHCI
+ bool "Octeon on-chip OHCI support (DEPRECATED)"
+ depends on CAVIUM_OCTEON_SOC
+ default USB_OCTEON_EHCI
+ select USB_OHCI_BIG_ENDIAN_MMIO
+ select USB_OHCI_LITTLE_ENDIAN
+ select USB_OHCI_HCD_PLATFORM
+ help
+ This option is deprecated now and the driver was removed, use
+ USB_OHCI_HCD_PLATFORM instead.
+
+ Enable support for the Octeon II SOC's on-chip OHCI
+ controller. It is needed for low-speed USB 1.0 device
+ support. All CN6XXX based chips with USB are supported.
+
+endif # USB_OHCI_HCD
+
+config USB_UHCI_HCD
+ tristate "UHCI HCD (most Intel and VIA) support"
+ depends on PCI || USB_UHCI_SUPPORT_NON_PCI_HC
+ ---help---
+ The Universal Host Controller Interface is a standard by Intel for
+ accessing the USB hardware in the PC (which is also called the USB
+ host controller). If your USB host controller conforms to this
+ standard, you may want to say Y, but see below. All recent boards
+ with Intel PCI chipsets (like intel 430TX, 440FX, 440LX, 440BX,
+ i810, i820) conform to this standard. Also all VIA PCI chipsets
+ (like VIA VP2, VP3, MVP3, Apollo Pro, Apollo Pro II or Apollo Pro
+ 133) and LEON/GRLIB SoCs with the GRUSBHC controller.
+ If unsure, say Y.
+
+ To compile this driver as a module, choose M here: the
+ module will be called uhci-hcd.
+
+config USB_UHCI_SUPPORT_NON_PCI_HC
+ bool
+ default y if (SPARC_LEON || USB_UHCI_PLATFORM)
+
+config USB_UHCI_PLATFORM
+ bool
+ default y if ARCH_VT8500
+
+config USB_UHCI_BIG_ENDIAN_MMIO
+ bool
+ default y if SPARC_LEON
+
+config USB_UHCI_BIG_ENDIAN_DESC
+ bool
+ default y if SPARC_LEON
+
+config USB_FHCI_HCD
+ tristate "Freescale QE USB Host Controller support"
+ depends on OF_GPIO && QE_GPIO && QUICC_ENGINE
+ select FSL_GTM
+ select QE_USB
+ help
+ This driver enables support for Freescale QE USB Host Controller
+ (as found on MPC8360 and MPC8323 processors), the driver supports
+ Full and Low Speed USB.
+
+config FHCI_DEBUG
+ bool "Freescale QE USB Host Controller debug support"
+ depends on USB_FHCI_HCD && DEBUG_FS
+ help
+ Say "y" to see some FHCI debug information and statistics
+ through debugfs.
+
+config USB_U132_HCD
+ tristate "Elan U132 Adapter Host Controller"
+ depends on USB_FTDI_ELAN
+ help
+ The U132 adapter is a USB to CardBus adapter specifically designed
+ for PC cards that contain an OHCI host controller. Typical PC cards
+ are the Orange Mobile 3G Option GlobeTrotter Fusion card. The U132
+ adapter will *NOT* work with PC cards that do not contain an OHCI
+ controller.
+
+ For those PC cards that contain multiple OHCI controllers only the
+ first one is used.
+
+ The driver consists of two modules, the "ftdi-elan" module is a
+ USB client driver that interfaces to the FTDI chip within ELAN's
+ USB-to-PCMCIA adapter, and this "u132-hcd" module is a USB host
+ controller driver that talks to the OHCI controller within the
+ CardBus cards that are inserted in the U132 adapter.
+
+ This driver has been tested with a CardBus OHCI USB adapter, and
+ worked with a USB PEN Drive inserted into the first USB port of
+ the PCCARD. A rather pointless thing to do, but useful for testing.
+
+ It is safe to say M here.
+
+ See also <http://www.elandigitalsystems.com/support/ufaq/u132linux.php>
+
+config USB_SL811_HCD
+ tristate "SL811HS HCD support"
+ help
+ The SL811HS is a single-port USB controller that supports either
+ host side or peripheral side roles. Enable this option if your
+ board has this chip, and you want to use it as a host controller.
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called sl811-hcd.
+
+config USB_SL811_HCD_ISO
+ bool "partial ISO support"
+ depends on USB_SL811_HCD
+ help
+ The driver doesn't support iso_frame_desc (yet), but for some simple
+ devices that just queue one ISO frame per URB, then ISO transfers
+ "should" work using the normal urb status fields.
+
+ If unsure, say N.
+
+config USB_SL811_CS
+ tristate "CF/PCMCIA support for SL811HS HCD"
+ depends on USB_SL811_HCD && PCMCIA
+ help
+ Wraps a PCMCIA driver around the SL811HS HCD, supporting the RATOC
+ REX-CFU1U CF card (often used with PDAs). If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called "sl811_cs".
+
+config USB_R8A66597_HCD
+ tristate "R8A66597 HCD support"
+ help
+ The R8A66597 is a USB 2.0 host and peripheral controller.
+
+ Enable this option if your board has this chip, and you want
+ to use it as a host controller. If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called r8a66597-hcd.
+
+config USB_RENESAS_USBHS_HCD
+ tristate "Renesas USBHS HCD support"
+ depends on USB_RENESAS_USBHS
+ help
+ The Renesas USBHS is a USB 2.0 host and peripheral controller.
+
+ Enable this option if your board has this chip, and you want
+ to use it as a host controller. If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called renesas-usbhs.
+
+config USB_WHCI_HCD
+ tristate "Wireless USB Host Controller Interface (WHCI) driver"
+ depends on PCI && USB && UWB
+ select USB_WUSB
+ select UWB_WHCI
+ help
+ A driver for PCI-based Wireless USB Host Controllers that are
+ compliant with the WHCI specification.
+
+ To compile this driver a module, choose M here: the module
+ will be called "whci-hcd".
+
+config USB_HWA_HCD
+ tristate "Host Wire Adapter (HWA) driver"
+ depends on USB && UWB
+ select USB_WUSB
+ select UWB_HWA
+ help
+ This driver enables you to connect Wireless USB devices to
+ your system using a Host Wire Adaptor USB dongle. This is an
+ UWB Radio Controller and WUSB Host Controller connected to
+ your machine via USB (specified in WUSB1.0).
+
+ To compile this driver a module, choose M here: the module
+ will be called "hwa-hc".
+
+config USB_IMX21_HCD
+ tristate "i.MX21 HCD support"
+ depends on ARM && ARCH_MXC
+ help
+ This driver enables support for the on-chip USB host in the
+ i.MX21 processor.
+
+ To compile this driver as a module, choose M here: the
+ module will be called "imx21-hcd".
+
+config USB_HCD_BCMA
+ tristate "BCMA usb host driver"
+ depends on BCMA
+ select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
+ select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
+ help
+ Enable support for the EHCI and OCHI host controller on an bcma bus.
+ It converts the bcma driver into two platform device drivers
+ for ehci and ohci.
+
+ If unsure, say N.
+
+config USB_HCD_SSB
+ tristate "SSB usb host driver"
+ depends on SSB
+ select USB_OHCI_HCD_PLATFORM if USB_OHCI_HCD
+ select USB_EHCI_HCD_PLATFORM if USB_EHCI_HCD
+ help
+ Enable support for the EHCI and OCHI host controller on an bcma bus.
+ It converts the bcma driver into two platform device drivers
+ for ehci and ohci.
+
+ If unsure, say N.
+
+config USB_HCD_TEST_MODE
+ bool "HCD test mode support"
+ ---help---
+ Say 'Y' to enable additional software test modes that may be
+ supported by the host controller drivers.
+
+ One such test mode is the Embedded High-speed Host Electrical Test
+ (EHSET) for EHCI host controller hardware, specifically the "Single
+ Step Set Feature" test. Typically this will be enabled for On-the-Go
+ or embedded hosts that need to undergo USB-IF compliance testing with
+ the aid of special testing hardware. In the future, this may expand
+ to include other tests that require support from a HCD driver.
+
+ This option is of interest only to developers who need to validate
+ their USB hardware designs. It is not needed for normal use. If
+ unsure, say N.
Code Review / kvmfornfv.git / blobdiff