--- /dev/null
+/*
+ * Copyright (C) 2011 Marvell International Ltd. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/timer.h>
+#include <linux/list.h>
+#include <linux/notifier.h>
+#include <linux/interrupt.h>
+#include <linux/moduleparam.h>
+#include <linux/device.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+#include <linux/pm.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/mv_usb.h>
+#include <linux/clk.h>
+
+#include "mv_u3d.h"
+
+#define DRIVER_DESC "Marvell PXA USB3.0 Device Controller driver"
+
+static const char driver_name[] = "mv_u3d";
+static const char driver_desc[] = DRIVER_DESC;
+
+static void mv_u3d_nuke(struct mv_u3d_ep *ep, int status);
+static void mv_u3d_stop_activity(struct mv_u3d *u3d,
+ struct usb_gadget_driver *driver);
+
+/* for endpoint 0 operations */
+static const struct usb_endpoint_descriptor mv_u3d_ep0_desc = {
+ .bLength = USB_DT_ENDPOINT_SIZE,
+ .bDescriptorType = USB_DT_ENDPOINT,
+ .bEndpointAddress = 0,
+ .bmAttributes = USB_ENDPOINT_XFER_CONTROL,
+ .wMaxPacketSize = MV_U3D_EP0_MAX_PKT_SIZE,
+};
+
+static void mv_u3d_ep0_reset(struct mv_u3d *u3d)
+{
+ struct mv_u3d_ep *ep;
+ u32 epxcr;
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ ep = &u3d->eps[i];
+ ep->u3d = u3d;
+
+ /* ep0 ep context, ep0 in and out share the same ep context */
+ ep->ep_context = &u3d->ep_context[1];
+ }
+
+ /* reset ep state machine */
+ /* reset ep0 out */
+ epxcr = ioread32(&u3d->vuc_regs->epcr[0].epxoutcr0);
+ epxcr |= MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxoutcr0);
+ udelay(5);
+ epxcr &= ~MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxoutcr0);
+
+ epxcr = ((MV_U3D_EP0_MAX_PKT_SIZE
+ << MV_U3D_EPXCR_MAX_PACKET_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_MAX_BURST_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | MV_U3D_EPXCR_EP_TYPE_CONTROL);
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxoutcr1);
+
+ /* reset ep0 in */
+ epxcr = ioread32(&u3d->vuc_regs->epcr[0].epxincr0);
+ epxcr |= MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxincr0);
+ udelay(5);
+ epxcr &= ~MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxincr0);
+
+ epxcr = ((MV_U3D_EP0_MAX_PKT_SIZE
+ << MV_U3D_EPXCR_MAX_PACKET_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_MAX_BURST_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | MV_U3D_EPXCR_EP_TYPE_CONTROL);
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[0].epxincr1);
+}
+
+static void mv_u3d_ep0_stall(struct mv_u3d *u3d)
+{
+ u32 tmp;
+ dev_dbg(u3d->dev, "%s\n", __func__);
+
+ /* set TX and RX to stall */
+ tmp = ioread32(&u3d->vuc_regs->epcr[0].epxoutcr0);
+ tmp |= MV_U3D_EPXCR_EP_HALT;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxoutcr0);
+
+ tmp = ioread32(&u3d->vuc_regs->epcr[0].epxincr0);
+ tmp |= MV_U3D_EPXCR_EP_HALT;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxincr0);
+
+ /* update ep0 state */
+ u3d->ep0_state = MV_U3D_WAIT_FOR_SETUP;
+ u3d->ep0_dir = MV_U3D_EP_DIR_OUT;
+}
+
+static int mv_u3d_process_ep_req(struct mv_u3d *u3d, int index,
+ struct mv_u3d_req *curr_req)
+{
+ struct mv_u3d_trb *curr_trb;
+ dma_addr_t cur_deq_lo;
+ struct mv_u3d_ep_context *curr_ep_context;
+ int trb_complete, actual, remaining_length = 0;
+ int direction, ep_num;
+ int retval = 0;
+ u32 tmp, status, length;
+
+ curr_ep_context = &u3d->ep_context[index];
+ direction = index % 2;
+ ep_num = index / 2;
+
+ trb_complete = 0;
+ actual = curr_req->req.length;
+
+ while (!list_empty(&curr_req->trb_list)) {
+ curr_trb = list_entry(curr_req->trb_list.next,
+ struct mv_u3d_trb, trb_list);
+ if (!curr_trb->trb_hw->ctrl.own) {
+ dev_err(u3d->dev, "%s, TRB own error!\n",
+ u3d->eps[index].name);
+ return 1;
+ }
+
+ curr_trb->trb_hw->ctrl.own = 0;
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ tmp = ioread32(&u3d->vuc_regs->rxst[ep_num].statuslo);
+ cur_deq_lo =
+ ioread32(&u3d->vuc_regs->rxst[ep_num].curdeqlo);
+ } else {
+ tmp = ioread32(&u3d->vuc_regs->txst[ep_num].statuslo);
+ cur_deq_lo =
+ ioread32(&u3d->vuc_regs->txst[ep_num].curdeqlo);
+ }
+
+ status = tmp >> MV_U3D_XFERSTATUS_COMPLETE_SHIFT;
+ length = tmp & MV_U3D_XFERSTATUS_TRB_LENGTH_MASK;
+
+ if (status == MV_U3D_COMPLETE_SUCCESS ||
+ (status == MV_U3D_COMPLETE_SHORT_PACKET &&
+ direction == MV_U3D_EP_DIR_OUT)) {
+ remaining_length += length;
+ actual -= remaining_length;
+ } else {
+ dev_err(u3d->dev,
+ "complete_tr error: ep=%d %s: error = 0x%x\n",
+ index >> 1, direction ? "SEND" : "RECV",
+ status);
+ retval = -EPROTO;
+ }
+
+ list_del_init(&curr_trb->trb_list);
+ }
+ if (retval)
+ return retval;
+
+ curr_req->req.actual = actual;
+ return 0;
+}
+
+/*
+ * mv_u3d_done() - retire a request; caller blocked irqs
+ * @status : request status to be set, only works when
+ * request is still in progress.
+ */
+static
+void mv_u3d_done(struct mv_u3d_ep *ep, struct mv_u3d_req *req, int status)
+ __releases(&ep->udc->lock)
+ __acquires(&ep->udc->lock)
+{
+ struct mv_u3d *u3d = (struct mv_u3d *)ep->u3d;
+
+ dev_dbg(u3d->dev, "mv_u3d_done: remove req->queue\n");
+ /* Removed the req from ep queue */
+ list_del_init(&req->queue);
+
+ /* req.status should be set as -EINPROGRESS in ep_queue() */
+ if (req->req.status == -EINPROGRESS)
+ req->req.status = status;
+ else
+ status = req->req.status;
+
+ /* Free trb for the request */
+ if (!req->chain)
+ dma_pool_free(u3d->trb_pool,
+ req->trb_head->trb_hw, req->trb_head->trb_dma);
+ else {
+ dma_unmap_single(ep->u3d->gadget.dev.parent,
+ (dma_addr_t)req->trb_head->trb_dma,
+ req->trb_count * sizeof(struct mv_u3d_trb_hw),
+ DMA_BIDIRECTIONAL);
+ kfree(req->trb_head->trb_hw);
+ }
+ kfree(req->trb_head);
+
+ usb_gadget_unmap_request(&u3d->gadget, &req->req, mv_u3d_ep_dir(ep));
+
+ if (status && (status != -ESHUTDOWN)) {
+ dev_dbg(u3d->dev, "complete %s req %p stat %d len %u/%u",
+ ep->ep.name, &req->req, status,
+ req->req.actual, req->req.length);
+ }
+
+ spin_unlock(&ep->u3d->lock);
+
+ usb_gadget_giveback_request(&ep->ep, &req->req);
+
+ spin_lock(&ep->u3d->lock);
+}
+
+static int mv_u3d_queue_trb(struct mv_u3d_ep *ep, struct mv_u3d_req *req)
+{
+ u32 tmp, direction;
+ struct mv_u3d *u3d;
+ struct mv_u3d_ep_context *ep_context;
+ int retval = 0;
+
+ u3d = ep->u3d;
+ direction = mv_u3d_ep_dir(ep);
+
+ /* ep0 in and out share the same ep context slot 1*/
+ if (ep->ep_num == 0)
+ ep_context = &(u3d->ep_context[1]);
+ else
+ ep_context = &(u3d->ep_context[ep->ep_num * 2 + direction]);
+
+ /* check if the pipe is empty or not */
+ if (!list_empty(&ep->queue)) {
+ dev_err(u3d->dev, "add trb to non-empty queue!\n");
+ retval = -ENOMEM;
+ WARN_ON(1);
+ } else {
+ ep_context->rsvd0 = cpu_to_le32(1);
+ ep_context->rsvd1 = 0;
+
+ /* Configure the trb address and set the DCS bit.
+ * Both DCS bit and own bit in trb should be set.
+ */
+ ep_context->trb_addr_lo =
+ cpu_to_le32(req->trb_head->trb_dma | DCS_ENABLE);
+ ep_context->trb_addr_hi = 0;
+
+ /* Ensure that updates to the EP Context will
+ * occure before Ring Bell.
+ */
+ wmb();
+
+ /* ring bell the ep */
+ if (ep->ep_num == 0)
+ tmp = 0x1;
+ else
+ tmp = ep->ep_num * 2
+ + ((direction == MV_U3D_EP_DIR_OUT) ? 0 : 1);
+
+ iowrite32(tmp, &u3d->op_regs->doorbell);
+ }
+ return retval;
+}
+
+static struct mv_u3d_trb *mv_u3d_build_trb_one(struct mv_u3d_req *req,
+ unsigned *length, dma_addr_t *dma)
+{
+ u32 temp;
+ unsigned int direction;
+ struct mv_u3d_trb *trb;
+ struct mv_u3d_trb_hw *trb_hw;
+ struct mv_u3d *u3d;
+
+ /* how big will this transfer be? */
+ *length = req->req.length - req->req.actual;
+ BUG_ON(*length > (unsigned)MV_U3D_EP_MAX_LENGTH_TRANSFER);
+
+ u3d = req->ep->u3d;
+
+ trb = kzalloc(sizeof(*trb), GFP_ATOMIC);
+ if (!trb)
+ return NULL;
+
+ /*
+ * Be careful that no _GFP_HIGHMEM is set,
+ * or we can not use dma_to_virt
+ * cannot use GFP_KERNEL in spin lock
+ */
+ trb_hw = dma_pool_alloc(u3d->trb_pool, GFP_ATOMIC, dma);
+ if (!trb_hw) {
+ kfree(trb);
+ dev_err(u3d->dev,
+ "%s, dma_pool_alloc fail\n", __func__);
+ return NULL;
+ }
+ trb->trb_dma = *dma;
+ trb->trb_hw = trb_hw;
+
+ /* initialize buffer page pointers */
+ temp = (u32)(req->req.dma + req->req.actual);
+
+ trb_hw->buf_addr_lo = cpu_to_le32(temp);
+ trb_hw->buf_addr_hi = 0;
+ trb_hw->trb_len = cpu_to_le32(*length);
+ trb_hw->ctrl.own = 1;
+
+ if (req->ep->ep_num == 0)
+ trb_hw->ctrl.type = TYPE_DATA;
+ else
+ trb_hw->ctrl.type = TYPE_NORMAL;
+
+ req->req.actual += *length;
+
+ direction = mv_u3d_ep_dir(req->ep);
+ if (direction == MV_U3D_EP_DIR_IN)
+ trb_hw->ctrl.dir = 1;
+ else
+ trb_hw->ctrl.dir = 0;
+
+ /* Enable interrupt for the last trb of a request */
+ if (!req->req.no_interrupt)
+ trb_hw->ctrl.ioc = 1;
+
+ trb_hw->ctrl.chain = 0;
+
+ wmb();
+ return trb;
+}
+
+static int mv_u3d_build_trb_chain(struct mv_u3d_req *req, unsigned *length,
+ struct mv_u3d_trb *trb, int *is_last)
+{
+ u32 temp;
+ unsigned int direction;
+ struct mv_u3d *u3d;
+
+ /* how big will this transfer be? */
+ *length = min(req->req.length - req->req.actual,
+ (unsigned)MV_U3D_EP_MAX_LENGTH_TRANSFER);
+
+ u3d = req->ep->u3d;
+
+ trb->trb_dma = 0;
+
+ /* initialize buffer page pointers */
+ temp = (u32)(req->req.dma + req->req.actual);
+
+ trb->trb_hw->buf_addr_lo = cpu_to_le32(temp);
+ trb->trb_hw->buf_addr_hi = 0;
+ trb->trb_hw->trb_len = cpu_to_le32(*length);
+ trb->trb_hw->ctrl.own = 1;
+
+ if (req->ep->ep_num == 0)
+ trb->trb_hw->ctrl.type = TYPE_DATA;
+ else
+ trb->trb_hw->ctrl.type = TYPE_NORMAL;
+
+ req->req.actual += *length;
+
+ direction = mv_u3d_ep_dir(req->ep);
+ if (direction == MV_U3D_EP_DIR_IN)
+ trb->trb_hw->ctrl.dir = 1;
+ else
+ trb->trb_hw->ctrl.dir = 0;
+
+ /* zlp is needed if req->req.zero is set */
+ if (req->req.zero) {
+ if (*length == 0 || (*length % req->ep->ep.maxpacket) != 0)
+ *is_last = 1;
+ else
+ *is_last = 0;
+ } else if (req->req.length == req->req.actual)
+ *is_last = 1;
+ else
+ *is_last = 0;
+
+ /* Enable interrupt for the last trb of a request */
+ if (*is_last && !req->req.no_interrupt)
+ trb->trb_hw->ctrl.ioc = 1;
+
+ if (*is_last)
+ trb->trb_hw->ctrl.chain = 0;
+ else {
+ trb->trb_hw->ctrl.chain = 1;
+ dev_dbg(u3d->dev, "chain trb\n");
+ }
+
+ wmb();
+
+ return 0;
+}
+
+/* generate TRB linked list for a request
+ * usb controller only supports continous trb chain,
+ * that trb structure physical address should be continous.
+ */
+static int mv_u3d_req_to_trb(struct mv_u3d_req *req)
+{
+ unsigned count;
+ int is_last;
+ struct mv_u3d_trb *trb;
+ struct mv_u3d_trb_hw *trb_hw;
+ struct mv_u3d *u3d;
+ dma_addr_t dma;
+ unsigned length;
+ unsigned trb_num;
+
+ u3d = req->ep->u3d;
+
+ INIT_LIST_HEAD(&req->trb_list);
+
+ length = req->req.length - req->req.actual;
+ /* normally the request transfer length is less than 16KB.
+ * we use buil_trb_one() to optimize it.
+ */
+ if (length <= (unsigned)MV_U3D_EP_MAX_LENGTH_TRANSFER) {
+ trb = mv_u3d_build_trb_one(req, &count, &dma);
+ list_add_tail(&trb->trb_list, &req->trb_list);
+ req->trb_head = trb;
+ req->trb_count = 1;
+ req->chain = 0;
+ } else {
+ trb_num = length / MV_U3D_EP_MAX_LENGTH_TRANSFER;
+ if (length % MV_U3D_EP_MAX_LENGTH_TRANSFER)
+ trb_num++;
+
+ trb = kcalloc(trb_num, sizeof(*trb), GFP_ATOMIC);
+ if (!trb)
+ return -ENOMEM;
+
+ trb_hw = kcalloc(trb_num, sizeof(*trb_hw), GFP_ATOMIC);
+ if (!trb_hw) {
+ kfree(trb);
+ return -ENOMEM;
+ }
+
+ do {
+ trb->trb_hw = trb_hw;
+ if (mv_u3d_build_trb_chain(req, &count,
+ trb, &is_last)) {
+ dev_err(u3d->dev,
+ "%s, mv_u3d_build_trb_chain fail\n",
+ __func__);
+ return -EIO;
+ }
+
+ list_add_tail(&trb->trb_list, &req->trb_list);
+ req->trb_count++;
+ trb++;
+ trb_hw++;
+ } while (!is_last);
+
+ req->trb_head = list_entry(req->trb_list.next,
+ struct mv_u3d_trb, trb_list);
+ req->trb_head->trb_dma = dma_map_single(u3d->gadget.dev.parent,
+ req->trb_head->trb_hw,
+ trb_num * sizeof(*trb_hw),
+ DMA_BIDIRECTIONAL);
+
+ req->chain = 1;
+ }
+
+ return 0;
+}
+
+static int
+mv_u3d_start_queue(struct mv_u3d_ep *ep)
+{
+ struct mv_u3d *u3d = ep->u3d;
+ struct mv_u3d_req *req;
+ int ret;
+
+ if (!list_empty(&ep->req_list) && !ep->processing)
+ req = list_entry(ep->req_list.next, struct mv_u3d_req, list);
+ else
+ return 0;
+
+ ep->processing = 1;
+
+ /* set up dma mapping */
+ ret = usb_gadget_map_request(&u3d->gadget, &req->req,
+ mv_u3d_ep_dir(ep));
+ if (ret)
+ return ret;
+
+ req->req.status = -EINPROGRESS;
+ req->req.actual = 0;
+ req->trb_count = 0;
+
+ /* build trbs and push them to device queue */
+ if (!mv_u3d_req_to_trb(req)) {
+ ret = mv_u3d_queue_trb(ep, req);
+ if (ret) {
+ ep->processing = 0;
+ return ret;
+ }
+ } else {
+ ep->processing = 0;
+ dev_err(u3d->dev, "%s, mv_u3d_req_to_trb fail\n", __func__);
+ return -ENOMEM;
+ }
+
+ /* irq handler advances the queue */
+ if (req)
+ list_add_tail(&req->queue, &ep->queue);
+
+ return 0;
+}
+
+static int mv_u3d_ep_enable(struct usb_ep *_ep,
+ const struct usb_endpoint_descriptor *desc)
+{
+ struct mv_u3d *u3d;
+ struct mv_u3d_ep *ep;
+ struct mv_u3d_ep_context *ep_context;
+ u16 max = 0;
+ unsigned maxburst = 0;
+ u32 epxcr, direction;
+
+ if (!_ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT)
+ return -EINVAL;
+
+ ep = container_of(_ep, struct mv_u3d_ep, ep);
+ u3d = ep->u3d;
+
+ if (!u3d->driver || u3d->gadget.speed == USB_SPEED_UNKNOWN)
+ return -ESHUTDOWN;
+
+ direction = mv_u3d_ep_dir(ep);
+ max = le16_to_cpu(desc->wMaxPacketSize);
+
+ if (!_ep->maxburst)
+ _ep->maxburst = 1;
+ maxburst = _ep->maxburst;
+
+ /* Get the endpoint context address */
+ ep_context = (struct mv_u3d_ep_context *)ep->ep_context;
+
+ /* Set the max burst size */
+ switch (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) {
+ case USB_ENDPOINT_XFER_BULK:
+ if (maxburst > 16) {
+ dev_dbg(u3d->dev,
+ "max burst should not be greater "
+ "than 16 on bulk ep\n");
+ maxburst = 1;
+ _ep->maxburst = maxburst;
+ }
+ dev_dbg(u3d->dev,
+ "maxburst: %d on bulk %s\n", maxburst, ep->name);
+ break;
+ case USB_ENDPOINT_XFER_CONTROL:
+ /* control transfer only supports maxburst as one */
+ maxburst = 1;
+ _ep->maxburst = maxburst;
+ break;
+ case USB_ENDPOINT_XFER_INT:
+ if (maxburst != 1) {
+ dev_dbg(u3d->dev,
+ "max burst should be 1 on int ep "
+ "if transfer size is not 1024\n");
+ maxburst = 1;
+ _ep->maxburst = maxburst;
+ }
+ break;
+ case USB_ENDPOINT_XFER_ISOC:
+ if (maxburst != 1) {
+ dev_dbg(u3d->dev,
+ "max burst should be 1 on isoc ep "
+ "if transfer size is not 1024\n");
+ maxburst = 1;
+ _ep->maxburst = maxburst;
+ }
+ break;
+ default:
+ goto en_done;
+ }
+
+ ep->ep.maxpacket = max;
+ ep->ep.desc = desc;
+ ep->enabled = 1;
+
+ /* Enable the endpoint for Rx or Tx and set the endpoint type */
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ epxcr = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+ epxcr |= MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+ udelay(5);
+ epxcr &= ~MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+
+ epxcr = ((max << MV_U3D_EPXCR_MAX_PACKET_SIZE_SHIFT)
+ | ((maxburst - 1) << MV_U3D_EPXCR_MAX_BURST_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK));
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr1);
+ } else {
+ epxcr = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+ epxcr |= MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+ udelay(5);
+ epxcr &= ~MV_U3D_EPXCR_EP_INIT;
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+
+ epxcr = ((max << MV_U3D_EPXCR_MAX_PACKET_SIZE_SHIFT)
+ | ((maxburst - 1) << MV_U3D_EPXCR_MAX_BURST_SIZE_SHIFT)
+ | (1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK));
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxincr1);
+ }
+
+ return 0;
+en_done:
+ return -EINVAL;
+}
+
+static int mv_u3d_ep_disable(struct usb_ep *_ep)
+{
+ struct mv_u3d *u3d;
+ struct mv_u3d_ep *ep;
+ struct mv_u3d_ep_context *ep_context;
+ u32 epxcr, direction;
+ unsigned long flags;
+
+ if (!_ep)
+ return -EINVAL;
+
+ ep = container_of(_ep, struct mv_u3d_ep, ep);
+ if (!ep->ep.desc)
+ return -EINVAL;
+
+ u3d = ep->u3d;
+
+ /* Get the endpoint context address */
+ ep_context = ep->ep_context;
+
+ direction = mv_u3d_ep_dir(ep);
+
+ /* nuke all pending requests (does flush) */
+ spin_lock_irqsave(&u3d->lock, flags);
+ mv_u3d_nuke(ep, -ESHUTDOWN);
+ spin_unlock_irqrestore(&u3d->lock, flags);
+
+ /* Disable the endpoint for Rx or Tx and reset the endpoint type */
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ epxcr = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxoutcr1);
+ epxcr &= ~((1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | USB_ENDPOINT_XFERTYPE_MASK);
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr1);
+ } else {
+ epxcr = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxincr1);
+ epxcr &= ~((1 << MV_U3D_EPXCR_EP_ENABLE_SHIFT)
+ | USB_ENDPOINT_XFERTYPE_MASK);
+ iowrite32(epxcr, &u3d->vuc_regs->epcr[ep->ep_num].epxincr1);
+ }
+
+ ep->enabled = 0;
+
+ ep->ep.desc = NULL;
+ return 0;
+}
+
+static struct usb_request *
+mv_u3d_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags)
+{
+ struct mv_u3d_req *req = NULL;
+
+ req = kzalloc(sizeof *req, gfp_flags);
+ if (!req)
+ return NULL;
+
+ INIT_LIST_HEAD(&req->queue);
+
+ return &req->req;
+}
+
+static void mv_u3d_free_request(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct mv_u3d_req *req = container_of(_req, struct mv_u3d_req, req);
+
+ kfree(req);
+}
+
+static void mv_u3d_ep_fifo_flush(struct usb_ep *_ep)
+{
+ struct mv_u3d *u3d;
+ u32 direction;
+ struct mv_u3d_ep *ep = container_of(_ep, struct mv_u3d_ep, ep);
+ unsigned int loops;
+ u32 tmp;
+
+ /* if endpoint is not enabled, cannot flush endpoint */
+ if (!ep->enabled)
+ return;
+
+ u3d = ep->u3d;
+ direction = mv_u3d_ep_dir(ep);
+
+ /* ep0 need clear bit after flushing fifo. */
+ if (!ep->ep_num) {
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ tmp = ioread32(&u3d->vuc_regs->epcr[0].epxoutcr0);
+ tmp |= MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxoutcr0);
+ udelay(10);
+ tmp &= ~MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxoutcr0);
+ } else {
+ tmp = ioread32(&u3d->vuc_regs->epcr[0].epxincr0);
+ tmp |= MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxincr0);
+ udelay(10);
+ tmp &= ~MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[0].epxincr0);
+ }
+ return;
+ }
+
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ tmp = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+ tmp |= MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+
+ /* Wait until flushing completed */
+ loops = LOOPS(MV_U3D_FLUSH_TIMEOUT);
+ while (ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0) &
+ MV_U3D_EPXCR_EP_FLUSH) {
+ /*
+ * EP_FLUSH bit should be cleared to indicate this
+ * operation is complete
+ */
+ if (loops == 0) {
+ dev_dbg(u3d->dev,
+ "EP FLUSH TIMEOUT for ep%d%s\n", ep->ep_num,
+ direction ? "in" : "out");
+ return;
+ }
+ loops--;
+ udelay(LOOPS_USEC);
+ }
+ } else { /* EP_DIR_IN */
+ tmp = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+ tmp |= MV_U3D_EPXCR_EP_FLUSH;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+
+ /* Wait until flushing completed */
+ loops = LOOPS(MV_U3D_FLUSH_TIMEOUT);
+ while (ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxincr0) &
+ MV_U3D_EPXCR_EP_FLUSH) {
+ /*
+ * EP_FLUSH bit should be cleared to indicate this
+ * operation is complete
+ */
+ if (loops == 0) {
+ dev_dbg(u3d->dev,
+ "EP FLUSH TIMEOUT for ep%d%s\n", ep->ep_num,
+ direction ? "in" : "out");
+ return;
+ }
+ loops--;
+ udelay(LOOPS_USEC);
+ }
+ }
+}
+
+/* queues (submits) an I/O request to an endpoint */
+static int
+mv_u3d_ep_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
+{
+ struct mv_u3d_ep *ep;
+ struct mv_u3d_req *req;
+ struct mv_u3d *u3d;
+ unsigned long flags;
+ int is_first_req = 0;
+
+ if (unlikely(!_ep || !_req))
+ return -EINVAL;
+
+ ep = container_of(_ep, struct mv_u3d_ep, ep);
+ u3d = ep->u3d;
+
+ req = container_of(_req, struct mv_u3d_req, req);
+
+ if (!ep->ep_num
+ && u3d->ep0_state == MV_U3D_STATUS_STAGE
+ && !_req->length) {
+ dev_dbg(u3d->dev, "ep0 status stage\n");
+ u3d->ep0_state = MV_U3D_WAIT_FOR_SETUP;
+ return 0;
+ }
+
+ dev_dbg(u3d->dev, "%s: %s, req: 0x%p\n",
+ __func__, _ep->name, req);
+
+ /* catch various bogus parameters */
+ if (!req->req.complete || !req->req.buf
+ || !list_empty(&req->queue)) {
+ dev_err(u3d->dev,
+ "%s, bad params, _req: 0x%p,"
+ "req->req.complete: 0x%p, req->req.buf: 0x%p,"
+ "list_empty: 0x%x\n",
+ __func__, _req,
+ req->req.complete, req->req.buf,
+ list_empty(&req->queue));
+ return -EINVAL;
+ }
+ if (unlikely(!ep->ep.desc)) {
+ dev_err(u3d->dev, "%s, bad ep\n", __func__);
+ return -EINVAL;
+ }
+ if (ep->ep.desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
+ if (req->req.length > ep->ep.maxpacket)
+ return -EMSGSIZE;
+ }
+
+ if (!u3d->driver || u3d->gadget.speed == USB_SPEED_UNKNOWN) {
+ dev_err(u3d->dev,
+ "bad params of driver/speed\n");
+ return -ESHUTDOWN;
+ }
+
+ req->ep = ep;
+
+ /* Software list handles usb request. */
+ spin_lock_irqsave(&ep->req_lock, flags);
+ is_first_req = list_empty(&ep->req_list);
+ list_add_tail(&req->list, &ep->req_list);
+ spin_unlock_irqrestore(&ep->req_lock, flags);
+ if (!is_first_req) {
+ dev_dbg(u3d->dev, "list is not empty\n");
+ return 0;
+ }
+
+ dev_dbg(u3d->dev, "call mv_u3d_start_queue from usb_ep_queue\n");
+ spin_lock_irqsave(&u3d->lock, flags);
+ mv_u3d_start_queue(ep);
+ spin_unlock_irqrestore(&u3d->lock, flags);
+ return 0;
+}
+
+/* dequeues (cancels, unlinks) an I/O request from an endpoint */
+static int mv_u3d_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+ struct mv_u3d_ep *ep;
+ struct mv_u3d_req *req;
+ struct mv_u3d *u3d;
+ struct mv_u3d_ep_context *ep_context;
+ struct mv_u3d_req *next_req;
+
+ unsigned long flags;
+ int ret = 0;
+
+ if (!_ep || !_req)
+ return -EINVAL;
+
+ ep = container_of(_ep, struct mv_u3d_ep, ep);
+ u3d = ep->u3d;
+
+ spin_lock_irqsave(&ep->u3d->lock, flags);
+
+ /* make sure it's actually queued on this endpoint */
+ list_for_each_entry(req, &ep->queue, queue) {
+ if (&req->req == _req)
+ break;
+ }
+ if (&req->req != _req) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ /* The request is in progress, or completed but not dequeued */
+ if (ep->queue.next == &req->queue) {
+ _req->status = -ECONNRESET;
+ mv_u3d_ep_fifo_flush(_ep);
+
+ /* The request isn't the last request in this ep queue */
+ if (req->queue.next != &ep->queue) {
+ dev_dbg(u3d->dev,
+ "it is the last request in this ep queue\n");
+ ep_context = ep->ep_context;
+ next_req = list_entry(req->queue.next,
+ struct mv_u3d_req, queue);
+
+ /* Point first TRB of next request to the EP context. */
+ iowrite32((unsigned long) next_req->trb_head,
+ &ep_context->trb_addr_lo);
+ } else {
+ struct mv_u3d_ep_context *ep_context;
+ ep_context = ep->ep_context;
+ ep_context->trb_addr_lo = 0;
+ ep_context->trb_addr_hi = 0;
+ }
+
+ } else
+ WARN_ON(1);
+
+ mv_u3d_done(ep, req, -ECONNRESET);
+
+ /* remove the req from the ep req list */
+ if (!list_empty(&ep->req_list)) {
+ struct mv_u3d_req *curr_req;
+ curr_req = list_entry(ep->req_list.next,
+ struct mv_u3d_req, list);
+ if (curr_req == req) {
+ list_del_init(&req->list);
+ ep->processing = 0;
+ }
+ }
+
+out:
+ spin_unlock_irqrestore(&ep->u3d->lock, flags);
+ return ret;
+}
+
+static void
+mv_u3d_ep_set_stall(struct mv_u3d *u3d, u8 ep_num, u8 direction, int stall)
+{
+ u32 tmp;
+ struct mv_u3d_ep *ep = u3d->eps;
+
+ dev_dbg(u3d->dev, "%s\n", __func__);
+ if (direction == MV_U3D_EP_DIR_OUT) {
+ tmp = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+ if (stall)
+ tmp |= MV_U3D_EPXCR_EP_HALT;
+ else
+ tmp &= ~MV_U3D_EPXCR_EP_HALT;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[ep->ep_num].epxoutcr0);
+ } else {
+ tmp = ioread32(&u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+ if (stall)
+ tmp |= MV_U3D_EPXCR_EP_HALT;
+ else
+ tmp &= ~MV_U3D_EPXCR_EP_HALT;
+ iowrite32(tmp, &u3d->vuc_regs->epcr[ep->ep_num].epxincr0);
+ }
+}
+
+static int mv_u3d_ep_set_halt_wedge(struct usb_ep *_ep, int halt, int wedge)
+{
+ struct mv_u3d_ep *ep;
+ unsigned long flags = 0;
+ int status = 0;
+ struct mv_u3d *u3d;
+
+ ep = container_of(_ep, struct mv_u3d_ep, ep);
+ u3d = ep->u3d;
+ if (!ep->ep.desc) {
+ status = -EINVAL;
+ goto out;
+ }
+
+ if (ep->ep.desc->bmAttributes == USB_ENDPOINT_XFER_ISOC) {
+ status = -EOPNOTSUPP;
+ goto out;
+ }
+
+ /*
+ * Attempt to halt IN ep will fail if any transfer requests
+ * are still queue
+ */
+ if (halt && (mv_u3d_ep_dir(ep) == MV_U3D_EP_DIR_IN)
+ && !list_empty(&ep->queue)) {
+ status = -EAGAIN;
+ goto out;
+ }
+
+ spin_lock_irqsave(&ep->u3d->lock, flags);
+ mv_u3d_ep_set_stall(u3d, ep->ep_num, mv_u3d_ep_dir(ep), halt);
+ if (halt && wedge)
+ ep->wedge = 1;
+ else if (!halt)
+ ep->wedge = 0;
+ spin_unlock_irqrestore(&ep->u3d->lock, flags);
+
+ if (ep->ep_num == 0)
+ u3d->ep0_dir = MV_U3D_EP_DIR_OUT;
+out:
+ return status;
+}
+
+static int mv_u3d_ep_set_halt(struct usb_ep *_ep, int halt)
+{
+ return mv_u3d_ep_set_halt_wedge(_ep, halt, 0);
+}
+
+static int mv_u3d_ep_set_wedge(struct usb_ep *_ep)
+{
+ return mv_u3d_ep_set_halt_wedge(_ep, 1, 1);
+}
+
+static struct usb_ep_ops mv_u3d_ep_ops = {
+ .enable = mv_u3d_ep_enable,
+ .disable = mv_u3d_ep_disable,
+
+ .alloc_request = mv_u3d_alloc_request,
+ .free_request = mv_u3d_free_request,
+
+ .queue = mv_u3d_ep_queue,
+ .dequeue = mv_u3d_ep_dequeue,
+
+ .set_wedge = mv_u3d_ep_set_wedge,
+ .set_halt = mv_u3d_ep_set_halt,
+ .fifo_flush = mv_u3d_ep_fifo_flush,
+};
+
+static void mv_u3d_controller_stop(struct mv_u3d *u3d)
+{
+ u32 tmp;
+
+ if (!u3d->clock_gating && u3d->vbus_valid_detect)
+ iowrite32(MV_U3D_INTR_ENABLE_VBUS_VALID,
+ &u3d->vuc_regs->intrenable);
+ else
+ iowrite32(0, &u3d->vuc_regs->intrenable);
+ iowrite32(~0x0, &u3d->vuc_regs->endcomplete);
+ iowrite32(~0x0, &u3d->vuc_regs->trbunderrun);
+ iowrite32(~0x0, &u3d->vuc_regs->trbcomplete);
+ iowrite32(~0x0, &u3d->vuc_regs->linkchange);
+ iowrite32(0x1, &u3d->vuc_regs->setuplock);
+
+ /* Reset the RUN bit in the command register to stop USB */
+ tmp = ioread32(&u3d->op_regs->usbcmd);
+ tmp &= ~MV_U3D_CMD_RUN_STOP;
+ iowrite32(tmp, &u3d->op_regs->usbcmd);
+ dev_dbg(u3d->dev, "after u3d_stop, USBCMD 0x%x\n",
+ ioread32(&u3d->op_regs->usbcmd));
+}
+
+static void mv_u3d_controller_start(struct mv_u3d *u3d)
+{
+ u32 usbintr;
+ u32 temp;
+
+ /* enable link LTSSM state machine */
+ temp = ioread32(&u3d->vuc_regs->ltssm);
+ temp |= MV_U3D_LTSSM_PHY_INIT_DONE;
+ iowrite32(temp, &u3d->vuc_regs->ltssm);
+
+ /* Enable interrupts */
+ usbintr = MV_U3D_INTR_ENABLE_LINK_CHG | MV_U3D_INTR_ENABLE_TXDESC_ERR |
+ MV_U3D_INTR_ENABLE_RXDESC_ERR | MV_U3D_INTR_ENABLE_TX_COMPLETE |
+ MV_U3D_INTR_ENABLE_RX_COMPLETE | MV_U3D_INTR_ENABLE_SETUP |
+ (u3d->vbus_valid_detect ? MV_U3D_INTR_ENABLE_VBUS_VALID : 0);
+ iowrite32(usbintr, &u3d->vuc_regs->intrenable);
+
+ /* Enable ctrl ep */
+ iowrite32(0x1, &u3d->vuc_regs->ctrlepenable);
+
+ /* Set the Run bit in the command register */
+ iowrite32(MV_U3D_CMD_RUN_STOP, &u3d->op_regs->usbcmd);
+ dev_dbg(u3d->dev, "after u3d_start, USBCMD 0x%x\n",
+ ioread32(&u3d->op_regs->usbcmd));
+}
+
+static int mv_u3d_controller_reset(struct mv_u3d *u3d)
+{
+ unsigned int loops;
+ u32 tmp;
+
+ /* Stop the controller */
+ tmp = ioread32(&u3d->op_regs->usbcmd);
+ tmp &= ~MV_U3D_CMD_RUN_STOP;
+ iowrite32(tmp, &u3d->op_regs->usbcmd);
+
+ /* Reset the controller to get default values */
+ iowrite32(MV_U3D_CMD_CTRL_RESET, &u3d->op_regs->usbcmd);
+
+ /* wait for reset to complete */
+ loops = LOOPS(MV_U3D_RESET_TIMEOUT);
+ while (ioread32(&u3d->op_regs->usbcmd) & MV_U3D_CMD_CTRL_RESET) {
+ if (loops == 0) {
+ dev_err(u3d->dev,
+ "Wait for RESET completed TIMEOUT\n");
+ return -ETIMEDOUT;
+ }
+ loops--;
+ udelay(LOOPS_USEC);
+ }
+
+ /* Configure the Endpoint Context Address */
+ iowrite32(u3d->ep_context_dma, &u3d->op_regs->dcbaapl);
+ iowrite32(0, &u3d->op_regs->dcbaaph);
+
+ return 0;
+}
+
+static int mv_u3d_enable(struct mv_u3d *u3d)
+{
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
+ int retval;
+
+ if (u3d->active)
+ return 0;
+
+ if (!u3d->clock_gating) {
+ u3d->active = 1;
+ return 0;
+ }
+
+ dev_dbg(u3d->dev, "enable u3d\n");
+ clk_enable(u3d->clk);
+ if (pdata->phy_init) {
+ retval = pdata->phy_init(u3d->phy_regs);
+ if (retval) {
+ dev_err(u3d->dev,
+ "init phy error %d\n", retval);
+ clk_disable(u3d->clk);
+ return retval;
+ }
+ }
+ u3d->active = 1;
+
+ return 0;
+}
+
+static void mv_u3d_disable(struct mv_u3d *u3d)
+{
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
+ if (u3d->clock_gating && u3d->active) {
+ dev_dbg(u3d->dev, "disable u3d\n");
+ if (pdata->phy_deinit)
+ pdata->phy_deinit(u3d->phy_regs);
+ clk_disable(u3d->clk);
+ u3d->active = 0;
+ }
+}
+
+static int mv_u3d_vbus_session(struct usb_gadget *gadget, int is_active)
+{
+ struct mv_u3d *u3d;
+ unsigned long flags;
+ int retval = 0;
+
+ u3d = container_of(gadget, struct mv_u3d, gadget);
+
+ spin_lock_irqsave(&u3d->lock, flags);
+
+ u3d->vbus_active = (is_active != 0);
+ dev_dbg(u3d->dev, "%s: softconnect %d, vbus_active %d\n",
+ __func__, u3d->softconnect, u3d->vbus_active);
+ /*
+ * 1. external VBUS detect: we can disable/enable clock on demand.
+ * 2. UDC VBUS detect: we have to enable clock all the time.
+ * 3. No VBUS detect: we have to enable clock all the time.
+ */
+ if (u3d->driver && u3d->softconnect && u3d->vbus_active) {
+ retval = mv_u3d_enable(u3d);
+ if (retval == 0) {
+ /*
+ * after clock is disabled, we lost all the register
+ * context. We have to re-init registers
+ */
+ mv_u3d_controller_reset(u3d);
+ mv_u3d_ep0_reset(u3d);
+ mv_u3d_controller_start(u3d);
+ }
+ } else if (u3d->driver && u3d->softconnect) {
+ if (!u3d->active)
+ goto out;
+
+ /* stop all the transfer in queue*/
+ mv_u3d_stop_activity(u3d, u3d->driver);
+ mv_u3d_controller_stop(u3d);
+ mv_u3d_disable(u3d);
+ }
+
+out:
+ spin_unlock_irqrestore(&u3d->lock, flags);
+ return retval;
+}
+
+/* constrain controller's VBUS power usage
+ * This call is used by gadget drivers during SET_CONFIGURATION calls,
+ * reporting how much power the device may consume. For example, this
+ * could affect how quickly batteries are recharged.
+ *
+ * Returns zero on success, else negative errno.
+ */
+static int mv_u3d_vbus_draw(struct usb_gadget *gadget, unsigned mA)
+{
+ struct mv_u3d *u3d = container_of(gadget, struct mv_u3d, gadget);
+
+ u3d->power = mA;
+
+ return 0;
+}
+
+static int mv_u3d_pullup(struct usb_gadget *gadget, int is_on)
+{
+ struct mv_u3d *u3d = container_of(gadget, struct mv_u3d, gadget);
+ unsigned long flags;
+ int retval = 0;
+
+ spin_lock_irqsave(&u3d->lock, flags);
+
+ dev_dbg(u3d->dev, "%s: softconnect %d, vbus_active %d\n",
+ __func__, u3d->softconnect, u3d->vbus_active);
+ u3d->softconnect = (is_on != 0);
+ if (u3d->driver && u3d->softconnect && u3d->vbus_active) {
+ retval = mv_u3d_enable(u3d);
+ if (retval == 0) {
+ /*
+ * after clock is disabled, we lost all the register
+ * context. We have to re-init registers
+ */
+ mv_u3d_controller_reset(u3d);
+ mv_u3d_ep0_reset(u3d);
+ mv_u3d_controller_start(u3d);
+ }
+ } else if (u3d->driver && u3d->vbus_active) {
+ /* stop all the transfer in queue*/
+ mv_u3d_stop_activity(u3d, u3d->driver);
+ mv_u3d_controller_stop(u3d);
+ mv_u3d_disable(u3d);
+ }
+
+ spin_unlock_irqrestore(&u3d->lock, flags);
+
+ return retval;
+}
+
+static int mv_u3d_start(struct usb_gadget *g,
+ struct usb_gadget_driver *driver)
+{
+ struct mv_u3d *u3d = container_of(g, struct mv_u3d, gadget);
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
+ unsigned long flags;
+
+ if (u3d->driver)
+ return -EBUSY;
+
+ spin_lock_irqsave(&u3d->lock, flags);
+
+ if (!u3d->clock_gating) {
+ clk_enable(u3d->clk);
+ if (pdata->phy_init)
+ pdata->phy_init(u3d->phy_regs);
+ }
+
+ /* hook up the driver ... */
+ driver->driver.bus = NULL;
+ u3d->driver = driver;
+
+ u3d->ep0_dir = USB_DIR_OUT;
+
+ spin_unlock_irqrestore(&u3d->lock, flags);
+
+ u3d->vbus_valid_detect = 1;
+
+ return 0;
+}
+
+static int mv_u3d_stop(struct usb_gadget *g)
+{
+ struct mv_u3d *u3d = container_of(g, struct mv_u3d, gadget);
+ struct mv_usb_platform_data *pdata = dev_get_platdata(u3d->dev);
+ unsigned long flags;
+
+ u3d->vbus_valid_detect = 0;
+ spin_lock_irqsave(&u3d->lock, flags);
+
+ /* enable clock to access controller register */
+ clk_enable(u3d->clk);
+ if (pdata->phy_init)
+ pdata->phy_init(u3d->phy_regs);
+
+ mv_u3d_controller_stop(u3d);
+ /* stop all usb activities */
+ u3d->gadget.speed = USB_SPEED_UNKNOWN;
+ mv_u3d_stop_activity(u3d, NULL);
+ mv_u3d_disable(u3d);
+
+ if (pdata->phy_deinit)
+ pdata->phy_deinit(u3d->phy_regs);
+ clk_disable(u3d->clk);
+
+ spin_unlock_irqrestore(&u3d->lock, flags);
+
+ u3d->driver = NULL;
+
+ return 0;
+}
+
+/* device controller usb_gadget_ops structure */
+static const struct usb_gadget_ops mv_u3d_ops = {
+ /* notify controller that VBUS is powered or not */
+ .vbus_session = mv_u3d_vbus_session,
+
+ /* constrain controller's VBUS power usage */
+ .vbus_draw = mv_u3d_vbus_draw,
+
+ .pullup = mv_u3d_pullup,
+ .udc_start = mv_u3d_start,
+ .udc_stop = mv_u3d_stop,
+};
+
+static int mv_u3d_eps_init(struct mv_u3d *u3d)
+{
+ struct mv_u3d_ep *ep;
+ char name[14];
+ int i;
+
+ /* initialize ep0, ep0 in/out use eps[1] */
+ ep = &u3d->eps[1];
+ ep->u3d = u3d;
+ strncpy(ep->name, "ep0", sizeof(ep->name));
+ ep->ep.name = ep->name;
+ ep->ep.ops = &mv_u3d_ep_ops;
+ ep->wedge = 0;
+ usb_ep_set_maxpacket_limit(&ep->ep, MV_U3D_EP0_MAX_PKT_SIZE);
+ ep->ep_num = 0;
+ ep->ep.desc = &mv_u3d_ep0_desc;
+ INIT_LIST_HEAD(&ep->queue);
+ INIT_LIST_HEAD(&ep->req_list);
+ ep->ep_type = USB_ENDPOINT_XFER_CONTROL;
+
+ /* add ep0 ep_context */
+ ep->ep_context = &u3d->ep_context[1];
+
+ /* initialize other endpoints */
+ for (i = 2; i < u3d->max_eps * 2; i++) {
+ ep = &u3d->eps[i];
+ if (i & 1) {
+ snprintf(name, sizeof(name), "ep%din", i >> 1);
+ ep->direction = MV_U3D_EP_DIR_IN;
+ } else {
+ snprintf(name, sizeof(name), "ep%dout", i >> 1);
+ ep->direction = MV_U3D_EP_DIR_OUT;
+ }
+ ep->u3d = u3d;
+ strncpy(ep->name, name, sizeof(ep->name));
+ ep->ep.name = ep->name;
+
+ ep->ep.ops = &mv_u3d_ep_ops;
+ usb_ep_set_maxpacket_limit(&ep->ep, (unsigned short) ~0);
+ ep->ep_num = i / 2;
+
+ INIT_LIST_HEAD(&ep->queue);
+ list_add_tail(&ep->ep.ep_list, &u3d->gadget.ep_list);
+
+ INIT_LIST_HEAD(&ep->req_list);
+ spin_lock_init(&ep->req_lock);
+ ep->ep_context = &u3d->ep_context[i];
+ }
+
+ return 0;
+}
+
+/* delete all endpoint requests, called with spinlock held */
+static void mv_u3d_nuke(struct mv_u3d_ep *ep, int status)
+{
+ /* endpoint fifo flush */
+ mv_u3d_ep_fifo_flush(&ep->ep);
+
+ while (!list_empty(&ep->queue)) {
+ struct mv_u3d_req *req = NULL;
+ req = list_entry(ep->queue.next, struct mv_u3d_req, queue);
+ mv_u3d_done(ep, req, status);
+ }
+}
+
+/* stop all USB activities */
+static
+void mv_u3d_stop_activity(struct mv_u3d *u3d, struct usb_gadget_driver *driver)
+{
+ struct mv_u3d_ep *ep;
+
+ mv_u3d_nuke(&u3d->eps[1], -ESHUTDOWN);
+
+ list_for_each_entry(ep, &u3d->gadget.ep_list, ep.ep_list) {
+ mv_u3d_nuke(ep, -ESHUTDOWN);
+ }
+
+ /* report disconnect; the driver is already quiesced */
+ if (driver) {
+ spin_unlock(&u3d->lock);
+ driver->disconnect(&u3d->gadget);
+ spin_lock(&u3d->lock);
+ }
+}
+
+static void mv_u3d_irq_process_error(struct mv_u3d *u3d)
+{
+ /* Increment the error count */
+ u3d->errors++;
+ dev_err(u3d->dev, "%s\n", __func__);
+}
+
+static void mv_u3d_irq_process_link_change(struct mv_u3d *u3d)
+{
+ u32 linkchange;
+
+ linkchange = ioread32(&u3d->vuc_regs->linkchange);
+ iowrite32(linkchange, &u3d->vuc_regs->linkchange);
+
+ dev_dbg(u3d->dev, "linkchange: 0x%x\n", linkchange);
+
+ if (linkchange & MV_U3D_LINK_CHANGE_LINK_UP) {
+ dev_dbg(u3d->dev, "link up: ltssm state: 0x%x\n",
+ ioread32(&u3d->vuc_regs->ltssmstate));
+
+ u3d->usb_state = USB_STATE_DEFAULT;
+ u3d->ep0_dir = MV_U3D_EP_DIR_OUT;
+ u3d->ep0_state = MV_U3D_WAIT_FOR_SETUP;
+
+ /* set speed */
+ u3d->gadget.speed = USB_SPEED_SUPER;
+ }
+
+ if (linkchange & MV_U3D_LINK_CHANGE_SUSPEND) {
+ dev_dbg(u3d->dev, "link suspend\n");
+ u3d->resume_state = u3d->usb_state;
+ u3d->usb_state = USB_STATE_SUSPENDED;
+ }
+
+ if (linkchange & MV_U3D_LINK_CHANGE_RESUME) {
+ dev_dbg(u3d->dev, "link resume\n");
+ u3d->usb_state = u3d->resume_state;
+ u3d->resume_state = 0;
+ }
+
+ if (linkchange & MV_U3D_LINK_CHANGE_WRESET) {
+ dev_dbg(u3d->dev, "warm reset\n");
+ u3d->usb_state = USB_STATE_POWERED;
+ }
+
+ if (linkchange & MV_U3D_LINK_CHANGE_HRESET) {
+ dev_dbg(u3d->dev, "hot reset\n");
+ u3d->usb_state = USB_STATE_DEFAULT;
+ }
+
+ if (linkchange & MV_U3D_LINK_CHANGE_INACT)
+ dev_dbg(u3d->dev, "inactive\n");
+
+ if (linkchange & MV_U3D_LINK_CHANGE_DISABLE_AFTER_U0)
+ dev_dbg(u3d->dev, "ss.disabled\n");
+
+ if (linkchange & MV_U3D_LINK_CHANGE_VBUS_INVALID) {
+ dev_dbg(u3d->dev, "vbus invalid\n");
+ u3d->usb_state = USB_STATE_ATTACHED;
+ u3d->vbus_valid_detect = 1;
+ /* if external vbus detect is not supported,
+ * we handle it here.
+ */
+ if (!u3d->vbus) {
+ spin_unlock(&u3d->lock);
+ mv_u3d_vbus_session(&u3d->gadget, 0);
+ spin_lock(&u3d->lock);
+ }
+ }
+}
+
+static void mv_u3d_ch9setaddress(struct mv_u3d *u3d,
+ struct usb_ctrlrequest *setup)
+{
+ u32 tmp;
+
+ if (u3d->usb_state != USB_STATE_DEFAULT) {
+ dev_err(u3d->dev,
+ "%s, cannot setaddr in this state (%d)\n",
+ __func__, u3d->usb_state);
+ goto err;
+ }
+
+ u3d->dev_addr = (u8)setup->wValue;
+
+ dev_dbg(u3d->dev, "%s: 0x%x\n", __func__, u3d->dev_addr);
+
+ if (u3d->dev_addr > 127) {
+ dev_err(u3d->dev,
+ "%s, u3d address is wrong (out of range)\n", __func__);
+ u3d->dev_addr = 0;
+ goto err;
+ }
+
+ /* update usb state */
+ u3d->usb_state = USB_STATE_ADDRESS;
+
+ /* set the new address */
+ tmp = ioread32(&u3d->vuc_regs->devaddrtiebrkr);
+ tmp &= ~0x7F;
+ tmp |= (u32)u3d->dev_addr;
+ iowrite32(tmp, &u3d->vuc_regs->devaddrtiebrkr);
+
+ return;
+err:
+ mv_u3d_ep0_stall(u3d);
+}
+
+static int mv_u3d_is_set_configuration(struct usb_ctrlrequest *setup)
+{
+ if ((setup->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD)
+ if (setup->bRequest == USB_REQ_SET_CONFIGURATION)
+ return 1;
+
+ return 0;
+}
+
+static void mv_u3d_handle_setup_packet(struct mv_u3d *u3d, u8 ep_num,
+ struct usb_ctrlrequest *setup)
+ __releases(&u3c->lock)
+ __acquires(&u3c->lock)
+{
+ bool delegate = false;
+
+ mv_u3d_nuke(&u3d->eps[ep_num * 2 + MV_U3D_EP_DIR_IN], -ESHUTDOWN);
+
+ dev_dbg(u3d->dev, "SETUP %02x.%02x v%04x i%04x l%04x\n",
+ setup->bRequestType, setup->bRequest,
+ setup->wValue, setup->wIndex, setup->wLength);
+
+ /* We process some stardard setup requests here */
+ if ((setup->bRequestType & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
+ switch (setup->bRequest) {
+ case USB_REQ_GET_STATUS:
+ delegate = true;
+ break;
+
+ case USB_REQ_SET_ADDRESS:
+ mv_u3d_ch9setaddress(u3d, setup);
+ break;
+
+ case USB_REQ_CLEAR_FEATURE:
+ delegate = true;
+ break;
+
+ case USB_REQ_SET_FEATURE:
+ delegate = true;
+ break;
+
+ default:
+ delegate = true;
+ }
+ } else
+ delegate = true;
+
+ /* delegate USB standard requests to the gadget driver */
+ if (delegate == true) {
+ /* USB requests handled by gadget */
+ if (setup->wLength) {
+ /* DATA phase from gadget, STATUS phase from u3d */
+ u3d->ep0_dir = (setup->bRequestType & USB_DIR_IN)
+ ? MV_U3D_EP_DIR_IN : MV_U3D_EP_DIR_OUT;
+ spin_unlock(&u3d->lock);
+ if (u3d->driver->setup(&u3d->gadget,
+ &u3d->local_setup_buff) < 0) {
+ dev_err(u3d->dev, "setup error!\n");
+ mv_u3d_ep0_stall(u3d);
+ }
+ spin_lock(&u3d->lock);
+ } else {
+ /* no DATA phase, STATUS phase from gadget */
+ u3d->ep0_dir = MV_U3D_EP_DIR_IN;
+ u3d->ep0_state = MV_U3D_STATUS_STAGE;
+ spin_unlock(&u3d->lock);
+ if (u3d->driver->setup(&u3d->gadget,
+ &u3d->local_setup_buff) < 0)
+ mv_u3d_ep0_stall(u3d);
+ spin_lock(&u3d->lock);
+ }
+
+ if (mv_u3d_is_set_configuration(setup)) {
+ dev_dbg(u3d->dev, "u3d configured\n");
+ u3d->usb_state = USB_STATE_CONFIGURED;
+ }
+ }
+}
+
+static void mv_u3d_get_setup_data(struct mv_u3d *u3d, u8 ep_num, u8 *buffer_ptr)
+{
+ struct mv_u3d_ep_context *epcontext;
+
+ epcontext = &u3d->ep_context[ep_num * 2 + MV_U3D_EP_DIR_IN];
+
+ /* Copy the setup packet to local buffer */
+ memcpy(buffer_ptr, (u8 *) &epcontext->setup_buffer, 8);
+}
+
+static void mv_u3d_irq_process_setup(struct mv_u3d *u3d)
+{
+ u32 tmp, i;
+ /* Process all Setup packet received interrupts */
+ tmp = ioread32(&u3d->vuc_regs->setuplock);
+ if (tmp) {
+ for (i = 0; i < u3d->max_eps; i++) {
+ if (tmp & (1 << i)) {
+ mv_u3d_get_setup_data(u3d, i,
+ (u8 *)(&u3d->local_setup_buff));
+ mv_u3d_handle_setup_packet(u3d, i,
+ &u3d->local_setup_buff);
+ }
+ }
+ }
+
+ iowrite32(tmp, &u3d->vuc_regs->setuplock);
+}
+
+static void mv_u3d_irq_process_tr_complete(struct mv_u3d *u3d)
+{
+ u32 tmp, bit_pos;
+ int i, ep_num = 0, direction = 0;
+ struct mv_u3d_ep *curr_ep;
+ struct mv_u3d_req *curr_req, *temp_req;
+ int status;
+
+ tmp = ioread32(&u3d->vuc_regs->endcomplete);
+
+ dev_dbg(u3d->dev, "tr_complete: ep: 0x%x\n", tmp);
+ if (!tmp)
+ return;
+ iowrite32(tmp, &u3d->vuc_regs->endcomplete);
+
+ for (i = 0; i < u3d->max_eps * 2; i++) {
+ ep_num = i >> 1;
+ direction = i % 2;
+
+ bit_pos = 1 << (ep_num + 16 * direction);
+
+ if (!(bit_pos & tmp))
+ continue;
+
+ if (i == 0)
+ curr_ep = &u3d->eps[1];
+ else
+ curr_ep = &u3d->eps[i];
+
+ /* remove req out of ep request list after completion */
+ dev_dbg(u3d->dev, "tr comp: check req_list\n");
+ spin_lock(&curr_ep->req_lock);
+ if (!list_empty(&curr_ep->req_list)) {
+ struct mv_u3d_req *req;
+ req = list_entry(curr_ep->req_list.next,
+ struct mv_u3d_req, list);
+ list_del_init(&req->list);
+ curr_ep->processing = 0;
+ }
+ spin_unlock(&curr_ep->req_lock);
+
+ /* process the req queue until an uncomplete request */
+ list_for_each_entry_safe(curr_req, temp_req,
+ &curr_ep->queue, queue) {
+ status = mv_u3d_process_ep_req(u3d, i, curr_req);
+ if (status)
+ break;
+ /* write back status to req */
+ curr_req->req.status = status;
+
+ /* ep0 request completion */
+ if (ep_num == 0) {
+ mv_u3d_done(curr_ep, curr_req, 0);
+ break;
+ } else {
+ mv_u3d_done(curr_ep, curr_req, status);
+ }
+ }
+
+ dev_dbg(u3d->dev, "call mv_u3d_start_queue from ep complete\n");
+ mv_u3d_start_queue(curr_ep);
+ }
+}
+
+static irqreturn_t mv_u3d_irq(int irq, void *dev)
+{
+ struct mv_u3d *u3d = (struct mv_u3d *)dev;
+ u32 status, intr;
+ u32 bridgesetting;
+ u32 trbunderrun;
+
+ spin_lock(&u3d->lock);
+
+ status = ioread32(&u3d->vuc_regs->intrcause);
+ intr = ioread32(&u3d->vuc_regs->intrenable);
+ status &= intr;
+
+ if (status == 0) {
+ spin_unlock(&u3d->lock);
+ dev_err(u3d->dev, "irq error!\n");
+ return IRQ_NONE;
+ }
+
+ if (status & MV_U3D_USBINT_VBUS_VALID) {
+ bridgesetting = ioread32(&u3d->vuc_regs->bridgesetting);
+ if (bridgesetting & MV_U3D_BRIDGE_SETTING_VBUS_VALID) {
+ /* write vbus valid bit of bridge setting to clear */
+ bridgesetting = MV_U3D_BRIDGE_SETTING_VBUS_VALID;
+ iowrite32(bridgesetting, &u3d->vuc_regs->bridgesetting);
+ dev_dbg(u3d->dev, "vbus valid\n");
+
+ u3d->usb_state = USB_STATE_POWERED;
+ u3d->vbus_valid_detect = 0;
+ /* if external vbus detect is not supported,
+ * we handle it here.
+ */
+ if (!u3d->vbus) {
+ spin_unlock(&u3d->lock);
+ mv_u3d_vbus_session(&u3d->gadget, 1);
+ spin_lock(&u3d->lock);
+ }
+ } else
+ dev_err(u3d->dev, "vbus bit is not set\n");
+ }
+
+ /* RX data is already in the 16KB FIFO.*/
+ if (status & MV_U3D_USBINT_UNDER_RUN) {
+ trbunderrun = ioread32(&u3d->vuc_regs->trbunderrun);
+ dev_err(u3d->dev, "under run, ep%d\n", trbunderrun);
+ iowrite32(trbunderrun, &u3d->vuc_regs->trbunderrun);
+ mv_u3d_irq_process_error(u3d);
+ }
+
+ if (status & (MV_U3D_USBINT_RXDESC_ERR | MV_U3D_USBINT_TXDESC_ERR)) {
+ /* write one to clear */
+ iowrite32(status & (MV_U3D_USBINT_RXDESC_ERR
+ | MV_U3D_USBINT_TXDESC_ERR),
+ &u3d->vuc_regs->intrcause);
+ dev_err(u3d->dev, "desc err 0x%x\n", status);
+ mv_u3d_irq_process_error(u3d);
+ }
+
+ if (status & MV_U3D_USBINT_LINK_CHG)
+ mv_u3d_irq_process_link_change(u3d);
+
+ if (status & MV_U3D_USBINT_TX_COMPLETE)
+ mv_u3d_irq_process_tr_complete(u3d);
+
+ if (status & MV_U3D_USBINT_RX_COMPLETE)
+ mv_u3d_irq_process_tr_complete(u3d);
+
+ if (status & MV_U3D_USBINT_SETUP)
+ mv_u3d_irq_process_setup(u3d);
+
+ spin_unlock(&u3d->lock);
+ return IRQ_HANDLED;
+}
+
+static int mv_u3d_remove(struct platform_device *dev)
+{
+ struct mv_u3d *u3d = platform_get_drvdata(dev);
+
+ BUG_ON(u3d == NULL);
+
+ usb_del_gadget_udc(&u3d->gadget);
+
+ /* free memory allocated in probe */
+ if (u3d->trb_pool)
+ dma_pool_destroy(u3d->trb_pool);
+
+ if (u3d->ep_context)
+ dma_free_coherent(&dev->dev, u3d->ep_context_size,
+ u3d->ep_context, u3d->ep_context_dma);
+
+ kfree(u3d->eps);
+
+ if (u3d->irq)
+ free_irq(u3d->irq, u3d);
+
+ if (u3d->cap_regs)
+ iounmap(u3d->cap_regs);
+ u3d->cap_regs = NULL;
+
+ kfree(u3d->status_req);
+
+ clk_put(u3d->clk);
+
+ kfree(u3d);
+
+ return 0;
+}
+
+static int mv_u3d_probe(struct platform_device *dev)
+{
+ struct mv_u3d *u3d = NULL;
+ struct mv_usb_platform_data *pdata = dev_get_platdata(&dev->dev);
+ int retval = 0;
+ struct resource *r;
+ size_t size;
+
+ if (!dev_get_platdata(&dev->dev)) {
+ dev_err(&dev->dev, "missing platform_data\n");
+ retval = -ENODEV;
+ goto err_pdata;
+ }
+
+ u3d = kzalloc(sizeof(*u3d), GFP_KERNEL);
+ if (!u3d) {
+ retval = -ENOMEM;
+ goto err_alloc_private;
+ }
+
+ spin_lock_init(&u3d->lock);
+
+ platform_set_drvdata(dev, u3d);
+
+ u3d->dev = &dev->dev;
+ u3d->vbus = pdata->vbus;
+
+ u3d->clk = clk_get(&dev->dev, NULL);
+ if (IS_ERR(u3d->clk)) {
+ retval = PTR_ERR(u3d->clk);
+ goto err_get_clk;
+ }
+
+ r = platform_get_resource_byname(dev, IORESOURCE_MEM, "capregs");
+ if (!r) {
+ dev_err(&dev->dev, "no I/O memory resource defined\n");
+ retval = -ENODEV;
+ goto err_get_cap_regs;
+ }
+
+ u3d->cap_regs = (struct mv_u3d_cap_regs __iomem *)
+ ioremap(r->start, resource_size(r));
+ if (!u3d->cap_regs) {
+ dev_err(&dev->dev, "failed to map I/O memory\n");
+ retval = -EBUSY;
+ goto err_map_cap_regs;
+ } else {
+ dev_dbg(&dev->dev, "cap_regs address: 0x%lx/0x%lx\n",
+ (unsigned long) r->start,
+ (unsigned long) u3d->cap_regs);
+ }
+
+ /* we will access controller register, so enable the u3d controller */
+ clk_enable(u3d->clk);
+
+ if (pdata->phy_init) {
+ retval = pdata->phy_init(u3d->phy_regs);
+ if (retval) {
+ dev_err(&dev->dev, "init phy error %d\n", retval);
+ goto err_u3d_enable;
+ }
+ }
+
+ u3d->op_regs = (struct mv_u3d_op_regs __iomem *)(u3d->cap_regs
+ + MV_U3D_USB3_OP_REGS_OFFSET);
+
+ u3d->vuc_regs = (struct mv_u3d_vuc_regs __iomem *)(u3d->cap_regs
+ + ioread32(&u3d->cap_regs->vuoff));
+
+ u3d->max_eps = 16;
+
+ /*
+ * some platform will use usb to download image, it may not disconnect
+ * usb gadget before loading kernel. So first stop u3d here.
+ */
+ mv_u3d_controller_stop(u3d);
+ iowrite32(0xFFFFFFFF, &u3d->vuc_regs->intrcause);
+
+ if (pdata->phy_deinit)
+ pdata->phy_deinit(u3d->phy_regs);
+ clk_disable(u3d->clk);
+
+ size = u3d->max_eps * sizeof(struct mv_u3d_ep_context) * 2;
+ size = (size + MV_U3D_EP_CONTEXT_ALIGNMENT - 1)
+ & ~(MV_U3D_EP_CONTEXT_ALIGNMENT - 1);
+ u3d->ep_context = dma_alloc_coherent(&dev->dev, size,
+ &u3d->ep_context_dma, GFP_KERNEL);
+ if (!u3d->ep_context) {
+ dev_err(&dev->dev, "allocate ep context memory failed\n");
+ retval = -ENOMEM;
+ goto err_alloc_ep_context;
+ }
+ u3d->ep_context_size = size;
+
+ /* create TRB dma_pool resource */
+ u3d->trb_pool = dma_pool_create("u3d_trb",
+ &dev->dev,
+ sizeof(struct mv_u3d_trb_hw),
+ MV_U3D_TRB_ALIGNMENT,
+ MV_U3D_DMA_BOUNDARY);
+
+ if (!u3d->trb_pool) {
+ retval = -ENOMEM;
+ goto err_alloc_trb_pool;
+ }
+
+ size = u3d->max_eps * sizeof(struct mv_u3d_ep) * 2;
+ u3d->eps = kzalloc(size, GFP_KERNEL);
+ if (!u3d->eps) {
+ retval = -ENOMEM;
+ goto err_alloc_eps;
+ }
+
+ /* initialize ep0 status request structure */
+ u3d->status_req = kzalloc(sizeof(struct mv_u3d_req) + 8, GFP_KERNEL);
+ if (!u3d->status_req) {
+ retval = -ENOMEM;
+ goto err_alloc_status_req;
+ }
+ INIT_LIST_HEAD(&u3d->status_req->queue);
+
+ /* allocate a small amount of memory to get valid address */
+ u3d->status_req->req.buf = (char *)u3d->status_req
+ + sizeof(struct mv_u3d_req);
+ u3d->status_req->req.dma = virt_to_phys(u3d->status_req->req.buf);
+
+ u3d->resume_state = USB_STATE_NOTATTACHED;
+ u3d->usb_state = USB_STATE_ATTACHED;
+ u3d->ep0_dir = MV_U3D_EP_DIR_OUT;
+ u3d->remote_wakeup = 0;
+
+ r = platform_get_resource(dev, IORESOURCE_IRQ, 0);
+ if (!r) {
+ dev_err(&dev->dev, "no IRQ resource defined\n");
+ retval = -ENODEV;
+ goto err_get_irq;
+ }
+ u3d->irq = r->start;
+ if (request_irq(u3d->irq, mv_u3d_irq,
+ IRQF_SHARED, driver_name, u3d)) {
+ u3d->irq = 0;
+ dev_err(&dev->dev, "Request irq %d for u3d failed\n",
+ u3d->irq);
+ retval = -ENODEV;
+ goto err_request_irq;
+ }
+
+ /* initialize gadget structure */
+ u3d->gadget.ops = &mv_u3d_ops; /* usb_gadget_ops */
+ u3d->gadget.ep0 = &u3d->eps[1].ep; /* gadget ep0 */
+ INIT_LIST_HEAD(&u3d->gadget.ep_list); /* ep_list */
+ u3d->gadget.speed = USB_SPEED_UNKNOWN; /* speed */
+
+ /* the "gadget" abstracts/virtualizes the controller */
+ u3d->gadget.name = driver_name; /* gadget name */
+
+ mv_u3d_eps_init(u3d);
+
+ /* external vbus detection */
+ if (u3d->vbus) {
+ u3d->clock_gating = 1;
+ dev_err(&dev->dev, "external vbus detection\n");
+ }
+
+ if (!u3d->clock_gating)
+ u3d->vbus_active = 1;
+
+ /* enable usb3 controller vbus detection */
+ u3d->vbus_valid_detect = 1;
+
+ retval = usb_add_gadget_udc(&dev->dev, &u3d->gadget);
+ if (retval)
+ goto err_unregister;
+
+ dev_dbg(&dev->dev, "successful probe usb3 device %s clock gating.\n",
+ u3d->clock_gating ? "with" : "without");
+
+ return 0;
+
+err_unregister:
+ free_irq(u3d->irq, u3d);
+err_request_irq:
+err_get_irq:
+ kfree(u3d->status_req);
+err_alloc_status_req:
+ kfree(u3d->eps);
+err_alloc_eps:
+ dma_pool_destroy(u3d->trb_pool);
+err_alloc_trb_pool:
+ dma_free_coherent(&dev->dev, u3d->ep_context_size,
+ u3d->ep_context, u3d->ep_context_dma);
+err_alloc_ep_context:
+ if (pdata->phy_deinit)
+ pdata->phy_deinit(u3d->phy_regs);
+ clk_disable(u3d->clk);
+err_u3d_enable:
+ iounmap(u3d->cap_regs);
+err_map_cap_regs:
+err_get_cap_regs:
+err_get_clk:
+ clk_put(u3d->clk);
+ kfree(u3d);
+err_alloc_private:
+err_pdata:
+ return retval;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int mv_u3d_suspend(struct device *dev)
+{
+ struct mv_u3d *u3d = dev_get_drvdata(dev);
+
+ /*
+ * only cable is unplugged, usb can suspend.
+ * So do not care about clock_gating == 1, it is handled by
+ * vbus session.
+ */
+ if (!u3d->clock_gating) {
+ mv_u3d_controller_stop(u3d);
+
+ spin_lock_irq(&u3d->lock);
+ /* stop all usb activities */
+ mv_u3d_stop_activity(u3d, u3d->driver);
+ spin_unlock_irq(&u3d->lock);
+
+ mv_u3d_disable(u3d);
+ }
+
+ return 0;
+}
+
+static int mv_u3d_resume(struct device *dev)
+{
+ struct mv_u3d *u3d = dev_get_drvdata(dev);
+ int retval;
+
+ if (!u3d->clock_gating) {
+ retval = mv_u3d_enable(u3d);
+ if (retval)
+ return retval;
+
+ if (u3d->driver && u3d->softconnect) {
+ mv_u3d_controller_reset(u3d);
+ mv_u3d_ep0_reset(u3d);
+ mv_u3d_controller_start(u3d);
+ }
+ }
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(mv_u3d_pm_ops, mv_u3d_suspend, mv_u3d_resume);
+
+static void mv_u3d_shutdown(struct platform_device *dev)
+{
+ struct mv_u3d *u3d = platform_get_drvdata(dev);
+ u32 tmp;
+
+ tmp = ioread32(&u3d->op_regs->usbcmd);
+ tmp &= ~MV_U3D_CMD_RUN_STOP;
+ iowrite32(tmp, &u3d->op_regs->usbcmd);
+}
+
+static struct platform_driver mv_u3d_driver = {
+ .probe = mv_u3d_probe,
+ .remove = mv_u3d_remove,
+ .shutdown = mv_u3d_shutdown,
+ .driver = {
+ .name = "mv-u3d",
+ .pm = &mv_u3d_pm_ops,
+ },
+};
+
+module_platform_driver(mv_u3d_driver);
+MODULE_ALIAS("platform:mv-u3d");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_AUTHOR("Yu Xu <yuxu@marvell.com>");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff