--- /dev/null
+/*
+ * This file is part of wlcore
+ *
+ * Copyright (C) 2011 Texas Instruments Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#ifndef __REG_H__
+#define __REG_H__
+
+#define WL18XX_REGISTERS_BASE 0x00800000
+#define WL18XX_CODE_BASE 0x00000000
+#define WL18XX_DATA_BASE 0x00400000
+#define WL18XX_DOUBLE_BUFFER_BASE 0x00600000
+#define WL18XX_MCU_KEY_SEARCH_BASE 0x00700000
+#define WL18XX_PHY_BASE 0x00900000
+#define WL18XX_TOP_OCP_BASE 0x00A00000
+#define WL18XX_PACKET_RAM_BASE 0x00B00000
+#define WL18XX_HOST_BASE 0x00C00000
+
+#define WL18XX_REGISTERS_DOWN_SIZE 0x0000B000
+
+#define WL18XX_REG_BOOT_PART_START 0x00802000
+#define WL18XX_REG_BOOT_PART_SIZE 0x00014578
+
+#define WL18XX_PHY_INIT_MEM_ADDR 0x80926000
+#define WL18XX_PHY_END_MEM_ADDR 0x8093CA44
+#define WL18XX_PHY_INIT_MEM_SIZE \
+ (WL18XX_PHY_END_MEM_ADDR - WL18XX_PHY_INIT_MEM_ADDR)
+
+#define WL18XX_SDIO_WSPI_BASE (WL18XX_REGISTERS_BASE)
+#define WL18XX_REG_CONFIG_BASE (WL18XX_REGISTERS_BASE + 0x02000)
+#define WL18XX_WGCM_REGS_BASE (WL18XX_REGISTERS_BASE + 0x03000)
+#define WL18XX_ENC_BASE (WL18XX_REGISTERS_BASE + 0x04000)
+#define WL18XX_INTERRUPT_BASE (WL18XX_REGISTERS_BASE + 0x05000)
+#define WL18XX_UART_BASE (WL18XX_REGISTERS_BASE + 0x06000)
+#define WL18XX_WELP_BASE (WL18XX_REGISTERS_BASE + 0x07000)
+#define WL18XX_TCP_CKSM_BASE (WL18XX_REGISTERS_BASE + 0x08000)
+#define WL18XX_FIFO_BASE (WL18XX_REGISTERS_BASE + 0x09000)
+#define WL18XX_OCP_BRIDGE_BASE (WL18XX_REGISTERS_BASE + 0x0A000)
+#define WL18XX_PMAC_RX_BASE (WL18XX_REGISTERS_BASE + 0x14800)
+#define WL18XX_PMAC_ACM_BASE (WL18XX_REGISTERS_BASE + 0x14C00)
+#define WL18XX_PMAC_TX_BASE (WL18XX_REGISTERS_BASE + 0x15000)
+#define WL18XX_PMAC_CSR_BASE (WL18XX_REGISTERS_BASE + 0x15400)
+
+#define WL18XX_REG_ECPU_CONTROL (WL18XX_REGISTERS_BASE + 0x02004)
+#define WL18XX_REG_INTERRUPT_NO_CLEAR (WL18XX_REGISTERS_BASE + 0x050E8)
+#define WL18XX_REG_INTERRUPT_ACK (WL18XX_REGISTERS_BASE + 0x050F0)
+#define WL18XX_REG_INTERRUPT_TRIG (WL18XX_REGISTERS_BASE + 0x5074)
+#define WL18XX_REG_INTERRUPT_TRIG_H (WL18XX_REGISTERS_BASE + 0x5078)
+#define WL18XX_REG_INTERRUPT_MASK (WL18XX_REGISTERS_BASE + 0x0050DC)
+
+#define WL18XX_REG_CHIP_ID_B (WL18XX_REGISTERS_BASE + 0x01542C)
+
+#define WL18XX_SLV_MEM_DATA (WL18XX_HOST_BASE + 0x0018)
+#define WL18XX_SLV_REG_DATA (WL18XX_HOST_BASE + 0x0008)
+
+/* Scratch Pad registers*/
+#define WL18XX_SCR_PAD0 (WL18XX_REGISTERS_BASE + 0x0154EC)
+#define WL18XX_SCR_PAD1 (WL18XX_REGISTERS_BASE + 0x0154F0)
+#define WL18XX_SCR_PAD2 (WL18XX_REGISTERS_BASE + 0x0154F4)
+#define WL18XX_SCR_PAD3 (WL18XX_REGISTERS_BASE + 0x0154F8)
+#define WL18XX_SCR_PAD4 (WL18XX_REGISTERS_BASE + 0x0154FC)
+#define WL18XX_SCR_PAD4_SET (WL18XX_REGISTERS_BASE + 0x015504)
+#define WL18XX_SCR_PAD4_CLR (WL18XX_REGISTERS_BASE + 0x015500)
+#define WL18XX_SCR_PAD5 (WL18XX_REGISTERS_BASE + 0x015508)
+#define WL18XX_SCR_PAD5_SET (WL18XX_REGISTERS_BASE + 0x015510)
+#define WL18XX_SCR_PAD5_CLR (WL18XX_REGISTERS_BASE + 0x01550C)
+#define WL18XX_SCR_PAD6 (WL18XX_REGISTERS_BASE + 0x015514)
+#define WL18XX_SCR_PAD7 (WL18XX_REGISTERS_BASE + 0x015518)
+#define WL18XX_SCR_PAD8 (WL18XX_REGISTERS_BASE + 0x01551C)
+#define WL18XX_SCR_PAD9 (WL18XX_REGISTERS_BASE + 0x015520)
+
+/* Spare registers*/
+#define WL18XX_SPARE_A1 (WL18XX_REGISTERS_BASE + 0x002194)
+#define WL18XX_SPARE_A2 (WL18XX_REGISTERS_BASE + 0x002198)
+#define WL18XX_SPARE_A3 (WL18XX_REGISTERS_BASE + 0x00219C)
+#define WL18XX_SPARE_A4 (WL18XX_REGISTERS_BASE + 0x0021A0)
+#define WL18XX_SPARE_A5 (WL18XX_REGISTERS_BASE + 0x0021A4)
+#define WL18XX_SPARE_A6 (WL18XX_REGISTERS_BASE + 0x0021A8)
+#define WL18XX_SPARE_A7 (WL18XX_REGISTERS_BASE + 0x0021AC)
+#define WL18XX_SPARE_A8 (WL18XX_REGISTERS_BASE + 0x0021B0)
+#define WL18XX_SPARE_B1 (WL18XX_REGISTERS_BASE + 0x015524)
+#define WL18XX_SPARE_B2 (WL18XX_REGISTERS_BASE + 0x015528)
+#define WL18XX_SPARE_B3 (WL18XX_REGISTERS_BASE + 0x01552C)
+#define WL18XX_SPARE_B4 (WL18XX_REGISTERS_BASE + 0x015530)
+#define WL18XX_SPARE_B5 (WL18XX_REGISTERS_BASE + 0x015534)
+#define WL18XX_SPARE_B6 (WL18XX_REGISTERS_BASE + 0x015538)
+#define WL18XX_SPARE_B7 (WL18XX_REGISTERS_BASE + 0x01553C)
+#define WL18XX_SPARE_B8 (WL18XX_REGISTERS_BASE + 0x015540)
+
+#define WL18XX_REG_COMMAND_MAILBOX_PTR (WL18XX_SCR_PAD0)
+#define WL18XX_REG_EVENT_MAILBOX_PTR (WL18XX_SCR_PAD1)
+#define WL18XX_EEPROMLESS_IND (WL18XX_SCR_PAD4)
+
+#define WL18XX_WELP_ARM_COMMAND (WL18XX_REGISTERS_BASE + 0x7100)
+#define WL18XX_ENABLE (WL18XX_REGISTERS_BASE + 0x01543C)
+
+/* PRCM registers */
+#define PLATFORM_DETECTION 0xA0E3E0
+#define OCS_EN 0xA02080
+#define PRIMARY_CLK_DETECT 0xA020A6
+#define PLLSH_COEX_PLL_N 0xA02384
+#define PLLSH_COEX_PLL_M 0xA02382
+#define PLLSH_COEX_PLL_SWALLOW_EN 0xA0238E
+#define PLLSH_WL_PLL_SEL 0xA02398
+
+#define PLLSH_WCS_PLL_N 0xA02362
+#define PLLSH_WCS_PLL_M 0xA02360
+#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1 0xA02364
+#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2 0xA02366
+#define PLLSH_WCS_PLL_P_FACTOR_CFG_1 0xA02368
+#define PLLSH_WCS_PLL_P_FACTOR_CFG_2 0xA0236A
+#define PLLSH_WCS_PLL_SWALLOW_EN 0xA0236C
+#define PLLSH_WL_PLL_EN 0xA02392
+
+#define PLLSH_WCS_PLL_Q_FACTOR_CFG_1_MASK 0xFFFF
+#define PLLSH_WCS_PLL_Q_FACTOR_CFG_2_MASK 0x007F
+#define PLLSH_WCS_PLL_P_FACTOR_CFG_1_MASK 0xFFFF
+#define PLLSH_WCS_PLL_P_FACTOR_CFG_2_MASK 0x000F
+
+#define PLLSH_WL_PLL_EN_VAL1 0x7
+#define PLLSH_WL_PLL_EN_VAL2 0x2
+#define PLLSH_COEX_PLL_SWALLOW_EN_VAL1 0x2
+#define PLLSH_COEX_PLL_SWALLOW_EN_VAL2 0x11
+
+#define PLLSH_WCS_PLL_SWALLOW_EN_VAL1 0x1
+#define PLLSH_WCS_PLL_SWALLOW_EN_VAL2 0x12
+
+#define PLLSH_WL_PLL_SEL_WCS_PLL 0x0
+#define PLLSH_WL_PLL_SEL_COEX_PLL 0x1
+
+#define WL18XX_REG_FUSE_DATA_1_3 0xA0260C
+#define WL18XX_PG_VER_MASK 0x70
+#define WL18XX_PG_VER_OFFSET 4
+#define WL18XX_ROM_VER_MASK 0x3e00
+#define WL18XX_ROM_VER_OFFSET 9
+#define WL18XX_METAL_VER_MASK 0xC
+#define WL18XX_METAL_VER_OFFSET 2
+#define WL18XX_NEW_METAL_VER_MASK 0x180
+#define WL18XX_NEW_METAL_VER_OFFSET 7
+
+#define WL18XX_PACKAGE_TYPE_OFFSET 13
+#define WL18XX_PACKAGE_TYPE_WSP 0
+
+#define WL18XX_REG_FUSE_DATA_2_3 0xA02614
+#define WL18XX_RDL_VER_MASK 0x1f00
+#define WL18XX_RDL_VER_OFFSET 8
+
+#define WL18XX_REG_FUSE_BD_ADDR_1 0xA02602
+#define WL18XX_REG_FUSE_BD_ADDR_2 0xA02606
+
+#define WL18XX_CMD_MBOX_ADDRESS 0xB007B4
+
+#define WL18XX_FW_STATUS_ADDR 0x50F8
+
+#define CHIP_ID_185x_PG10 (0x06030101)
+#define CHIP_ID_185x_PG20 (0x06030111)
+
+/*
+ * Host Command Interrupt. Setting this bit masks
+ * the interrupt that the host issues to inform
+ * the FW that it has sent a command
+ * to the Wlan hardware Command Mailbox.
+ */
+#define WL18XX_INTR_TRIG_CMD BIT(28)
+
+/*
+ * Host Event Acknowlegde Interrupt. The host
+ * sets this bit to acknowledge that it received
+ * the unsolicited information from the event
+ * mailbox.
+ */
+#define WL18XX_INTR_TRIG_EVENT_ACK BIT(29)
+
+/*
+ * To boot the firmware in PLT mode we need to write this value in
+ * SCR_PAD8 before starting.
+ */
+#define WL18XX_SCR_PAD8_PLT 0xBABABEBE
+
+enum {
+ COMPONENT_NO_SWITCH = 0x0,
+ COMPONENT_2_WAY_SWITCH = 0x1,
+ COMPONENT_3_WAY_SWITCH = 0x2,
+ COMPONENT_MATCHING = 0x3,
+};
+
+enum {
+ FEM_NONE = 0x0,
+ FEM_VENDOR_1 = 0x1,
+ FEM_VENDOR_2 = 0x2,
+ FEM_VENDOR_3 = 0x3,
+};
+
+enum {
+ BOARD_TYPE_EVB_18XX = 0,
+ BOARD_TYPE_DVP_18XX = 1,
+ BOARD_TYPE_HDK_18XX = 2,
+ BOARD_TYPE_FPGA_18XX = 3,
+ BOARD_TYPE_COM8_18XX = 4,
+
+ NUM_BOARD_TYPES,
+};
+
+enum wl18xx_rdl_num {
+ RDL_NONE = 0,
+ RDL_1_HP = 1,
+ RDL_2_SP = 2,
+ RDL_3_HP = 3,
+ RDL_4_SP = 4,
+ RDL_5_SP = 0x11,
+ RDL_6_SP = 0x12,
+ RDL_7_SP = 0x13,
+ RDL_8_SP = 0x14,
+
+ _RDL_LAST,
+ RDL_MAX = _RDL_LAST - 1,
+};
+
+
+/* FPGA_SPARE_1 register - used to change the PHY ATPG clock at boot time */
+#define WL18XX_PHY_FPGA_SPARE_1 0x8093CA40
+
+/* command to disable FDSP clock */
+#define MEM_FDSP_CLK_120_DISABLE 0x80000000
+
+/* command to set ATPG clock toward FDSP Code RAM rather than its own clock */
+#define MEM_FDSP_CODERAM_FUNC_CLK_SEL 0xC0000000
+
+/* command to re-enable FDSP clock */
+#define MEM_FDSP_CLK_120_ENABLE 0x40000000
+
+#endif /* __REG_H__ */
Code Review / kvmfornfv.git / blobdiff