--- /dev/null
+config ATH9K_HW
+ tristate
+config ATH9K_COMMON
+ tristate
+ select ATH_COMMON
+ select DEBUG_FS
+ select RELAY
+config ATH9K_DFS_DEBUGFS
+ def_bool y
+ depends on ATH9K_DEBUGFS && ATH9K_DFS_CERTIFIED
+
+config ATH9K_BTCOEX_SUPPORT
+ bool "Atheros bluetooth coexistence support"
+ depends on (ATH9K || ATH9K_HTC)
+ default y
+ ---help---
+ Say Y, if you want to use the ath9k/ath9k_htc radios together with
+ Bluetooth modules in the same system.
+
+config ATH9K
+ tristate "Atheros 802.11n wireless cards support"
+ depends on MAC80211 && HAS_DMA
+ select ATH9K_HW
+ select MAC80211_LEDS
+ select LEDS_CLASS
+ select NEW_LEDS
+ select ATH9K_COMMON
+ ---help---
+ This module adds support for wireless adapters based on
+ Atheros IEEE 802.11n AR5008, AR9001 and AR9002 family
+ of chipsets. For a specific list of supported external
+ cards, laptops that already ship with these cards and
+ APs that come with these cards refer to ath9k wiki
+ products page:
+
+ http://wireless.kernel.org/en/users/Drivers/ath9k/products
+
+ If you choose to build a module, it'll be called ath9k.
+
+config ATH9K_PCI
+ bool "Atheros ath9k PCI/PCIe bus support"
+ default y
+ depends on ATH9K && PCI
+ ---help---
+ This option enables the PCI bus support in ath9k.
+
+ Say Y, if you have a compatible PCI/PCIe wireless card.
+
+config ATH9K_AHB
+ bool "Atheros ath9k AHB bus support"
+ depends on ATH9K
+ default n
+ ---help---
+ This option enables the AHB bus support in ath9k.
+
+ Say Y, if you have a SoC with a compatible built-in
+ wireless MAC. Say N if unsure.
+
+config ATH9K_DEBUGFS
+ bool "Atheros ath9k debugging"
+ depends on ATH9K && DEBUG_FS
+ select MAC80211_DEBUGFS
+ select RELAY
+ ---help---
+ Say Y, if you need access to ath9k's statistics for
+ interrupts, rate control, etc.
+
+ Also required for changing debug message flags at run time.
+
+config ATH9K_STATION_STATISTICS
+ bool "Detailed station statistics"
+ depends on ATH9K && ATH9K_DEBUGFS && DEBUG_FS
+ select MAC80211_DEBUGFS
+ default n
+ ---help---
+ This option enables detailed statistics for association stations.
+
+config ATH9K_DFS_CERTIFIED
+ bool "Atheros DFS support for certified platforms"
+ depends on ATH9K && CFG80211_CERTIFICATION_ONUS
+ default n
+ ---help---
+ This option enables DFS support for initiating radiation on
+ ath9k. There is no way to dynamically detect if a card was DFS
+ certified and as such this is left as a build time option. This
+ option should only be enabled by system integrators that can
+ guarantee that all the platforms that their kernel will run on
+ have obtained appropriate regulatory body certification for a
+ respective Atheros card by using ath9k on the target shipping
+ platforms.
+
+ This is currently only a placeholder for future DFS support,
+ as DFS support requires more components that still need to be
+ developed. At this point enabling this option won't do anything
+ except increase code size.
+
+config ATH9K_DYNACK
+ bool "Atheros ath9k ACK timeout estimation algorithm (EXPERIMENTAL)"
+ depends on ATH9K
+ default n
+ ---help---
+ This option enables ath9k dynamic ACK timeout estimation algorithm
+ based on ACK frame RX timestamp, TX frame timestamp and frame
+ duration
+
+config ATH9K_TX99
+ bool "Atheros ath9k TX99 testing support"
+ depends on ATH9K_DEBUGFS && CFG80211_CERTIFICATION_ONUS
+ default n
+ ---help---
+ Say N. This should only be enabled on systems undergoing
+ certification testing and evaluation in a controlled environment.
+ Enabling this will only enable TX99 support, all other modes of
+ operation will be disabled.
+
+ TX99 support enables Specific Absorption Rate (SAR) testing.
+ SAR is the unit of measurement for the amount of radio frequency(RF)
+ absorbed by the body when using a wireless device. The RF exposure
+ limits used are expressed in the terms of SAR, which is a measure
+ of the electric and magnetic field strength and power density for
+ transmitters operating at frequencies from 300 kHz to 100 GHz.
+ Regulatory bodies around the world require that wireless device
+ be evaluated to meet the RF exposure limits set forth in the
+ governmental SAR regulations.
+
+config ATH9K_WOW
+ bool "Wake on Wireless LAN support (EXPERIMENTAL)"
+ depends on ATH9K && PM
+ default n
+ ---help---
+ This option enables Wake on Wireless LAN support for certain cards.
+ Currently, AR9462 is supported.
+
+config ATH9K_RFKILL
+ bool "Atheros ath9k rfkill support" if EXPERT
+ depends on ATH9K
+ depends on RFKILL=y || RFKILL=ATH9K
+ default y
+ help
+ Say Y to have ath9k poll the RF-Kill GPIO every couple of
+ seconds. Turn off to save power, but enable it if you have
+ a platform that can toggle the RF-Kill GPIO.
+
+config ATH9K_CHANNEL_CONTEXT
+ bool "Channel Context support"
+ depends on ATH9K
+ default n
+ ---help---
+ This option enables channel context support in ath9k, which is needed
+ for multi-channel concurrency. Enable this if P2P PowerSave support
+ is required.
+
+config ATH9K_PCOEM
+ bool "Atheros ath9k support for PC OEM cards" if EXPERT
+ depends on ATH9K
+ default y
+
+config ATH9K_HTC
+ tristate "Atheros HTC based wireless cards support"
+ depends on USB && MAC80211
+ select ATH9K_HW
+ select MAC80211_LEDS
+ select LEDS_CLASS
+ select NEW_LEDS
+ select ATH9K_COMMON
+ ---help---
+ Support for Atheros HTC based cards.
+ Chipsets supported: AR9271
+
+ For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htc
+
+ The built module will be ath9k_htc.
+
+config ATH9K_HTC_DEBUGFS
+ bool "Atheros ath9k_htc debugging"
+ depends on ATH9K_HTC && DEBUG_FS
+ ---help---
+ Say Y, if you need access to ath9k_htc's statistics.
Code Review / kvmfornfv.git / blobdiff