--- /dev/null
+/*
+ * Copyright (c) 2012 Bjørn Mork <bjorn@mork.no>
+ *
+ * The probing code is heavily inspired by cdc_ether, which is:
+ * Copyright (C) 2003-2005 by David Brownell
+ * Copyright (C) 2006 by Ole Andre Vadla Ravnas (ActiveSync)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/ethtool.h>
+#include <linux/etherdevice.h>
+#include <linux/mii.h>
+#include <linux/usb.h>
+#include <linux/usb/cdc.h>
+#include <linux/usb/usbnet.h>
+#include <linux/usb/cdc-wdm.h>
+
+/* This driver supports wwan (3G/LTE/?) devices using a vendor
+ * specific management protocol called Qualcomm MSM Interface (QMI) -
+ * in addition to the more common AT commands over serial interface
+ * management
+ *
+ * QMI is wrapped in CDC, using CDC encapsulated commands on the
+ * control ("master") interface of a two-interface CDC Union
+ * resembling standard CDC ECM. The devices do not use the control
+ * interface for any other CDC messages. Most likely because the
+ * management protocol is used in place of the standard CDC
+ * notifications NOTIFY_NETWORK_CONNECTION and NOTIFY_SPEED_CHANGE
+ *
+ * Alternatively, control and data functions can be combined in a
+ * single USB interface.
+ *
+ * Handling a protocol like QMI is out of the scope for any driver.
+ * It is exported as a character device using the cdc-wdm driver as
+ * a subdriver, enabling userspace applications ("modem managers") to
+ * handle it.
+ *
+ * These devices may alternatively/additionally be configured using AT
+ * commands on a serial interface
+ */
+
+/* driver specific data */
+struct qmi_wwan_state {
+ struct usb_driver *subdriver;
+ atomic_t pmcount;
+ unsigned long unused;
+ struct usb_interface *control;
+ struct usb_interface *data;
+};
+
+/* default ethernet address used by the modem */
+static const u8 default_modem_addr[ETH_ALEN] = {0x02, 0x50, 0xf3};
+
+static const u8 buggy_fw_addr[ETH_ALEN] = {0x00, 0xa0, 0xc6, 0x00, 0x00, 0x00};
+
+/* Make up an ethernet header if the packet doesn't have one.
+ *
+ * A firmware bug common among several devices cause them to send raw
+ * IP packets under some circumstances. There is no way for the
+ * driver/host to know when this will happen. And even when the bug
+ * hits, some packets will still arrive with an intact header.
+ *
+ * The supported devices are only capably of sending IPv4, IPv6 and
+ * ARP packets on a point-to-point link. Any packet with an ethernet
+ * header will have either our address or a broadcast/multicast
+ * address as destination. ARP packets will always have a header.
+ *
+ * This means that this function will reliably add the appropriate
+ * header iff necessary, provided our hardware address does not start
+ * with 4 or 6.
+ *
+ * Another common firmware bug results in all packets being addressed
+ * to 00:a0:c6:00:00:00 despite the host address being different.
+ * This function will also fixup such packets.
+ */
+static int qmi_wwan_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
+{
+ __be16 proto;
+
+ /* This check is no longer done by usbnet */
+ if (skb->len < dev->net->hard_header_len)
+ return 0;
+
+ switch (skb->data[0] & 0xf0) {
+ case 0x40:
+ proto = htons(ETH_P_IP);
+ break;
+ case 0x60:
+ proto = htons(ETH_P_IPV6);
+ break;
+ case 0x00:
+ if (is_multicast_ether_addr(skb->data))
+ return 1;
+ /* possibly bogus destination - rewrite just in case */
+ skb_reset_mac_header(skb);
+ goto fix_dest;
+ default:
+ /* pass along other packets without modifications */
+ return 1;
+ }
+ if (skb_headroom(skb) < ETH_HLEN)
+ return 0;
+ skb_push(skb, ETH_HLEN);
+ skb_reset_mac_header(skb);
+ eth_hdr(skb)->h_proto = proto;
+ eth_zero_addr(eth_hdr(skb)->h_source);
+fix_dest:
+ memcpy(eth_hdr(skb)->h_dest, dev->net->dev_addr, ETH_ALEN);
+ return 1;
+}
+
+/* very simplistic detection of IPv4 or IPv6 headers */
+static bool possibly_iphdr(const char *data)
+{
+ return (data[0] & 0xd0) == 0x40;
+}
+
+/* disallow addresses which may be confused with IP headers */
+static int qmi_wwan_mac_addr(struct net_device *dev, void *p)
+{
+ int ret;
+ struct sockaddr *addr = p;
+
+ ret = eth_prepare_mac_addr_change(dev, p);
+ if (ret < 0)
+ return ret;
+ if (possibly_iphdr(addr->sa_data))
+ return -EADDRNOTAVAIL;
+ eth_commit_mac_addr_change(dev, p);
+ return 0;
+}
+
+static const struct net_device_ops qmi_wwan_netdev_ops = {
+ .ndo_open = usbnet_open,
+ .ndo_stop = usbnet_stop,
+ .ndo_start_xmit = usbnet_start_xmit,
+ .ndo_tx_timeout = usbnet_tx_timeout,
+ .ndo_change_mtu = usbnet_change_mtu,
+ .ndo_set_mac_address = qmi_wwan_mac_addr,
+ .ndo_validate_addr = eth_validate_addr,
+};
+
+/* using a counter to merge subdriver requests with our own into a
+ * combined state
+ */
+static int qmi_wwan_manage_power(struct usbnet *dev, int on)
+{
+ struct qmi_wwan_state *info = (void *)&dev->data;
+ int rv;
+
+ dev_dbg(&dev->intf->dev, "%s() pmcount=%d, on=%d\n", __func__,
+ atomic_read(&info->pmcount), on);
+
+ if ((on && atomic_add_return(1, &info->pmcount) == 1) ||
+ (!on && atomic_dec_and_test(&info->pmcount))) {
+ /* need autopm_get/put here to ensure the usbcore sees
+ * the new value
+ */
+ rv = usb_autopm_get_interface(dev->intf);
+ dev->intf->needs_remote_wakeup = on;
+ if (!rv)
+ usb_autopm_put_interface(dev->intf);
+ }
+ return 0;
+}
+
+static int qmi_wwan_cdc_wdm_manage_power(struct usb_interface *intf, int on)
+{
+ struct usbnet *dev = usb_get_intfdata(intf);
+
+ /* can be called while disconnecting */
+ if (!dev)
+ return 0;
+ return qmi_wwan_manage_power(dev, on);
+}
+
+/* collect all three endpoints and register subdriver */
+static int qmi_wwan_register_subdriver(struct usbnet *dev)
+{
+ int rv;
+ struct usb_driver *subdriver = NULL;
+ struct qmi_wwan_state *info = (void *)&dev->data;
+
+ /* collect bulk endpoints */
+ rv = usbnet_get_endpoints(dev, info->data);
+ if (rv < 0)
+ goto err;
+
+ /* update status endpoint if separate control interface */
+ if (info->control != info->data)
+ dev->status = &info->control->cur_altsetting->endpoint[0];
+
+ /* require interrupt endpoint for subdriver */
+ if (!dev->status) {
+ rv = -EINVAL;
+ goto err;
+ }
+
+ /* for subdriver power management */
+ atomic_set(&info->pmcount, 0);
+
+ /* register subdriver */
+ subdriver = usb_cdc_wdm_register(info->control, &dev->status->desc,
+ 4096, &qmi_wwan_cdc_wdm_manage_power);
+ if (IS_ERR(subdriver)) {
+ dev_err(&info->control->dev, "subdriver registration failed\n");
+ rv = PTR_ERR(subdriver);
+ goto err;
+ }
+
+ /* prevent usbnet from using status endpoint */
+ dev->status = NULL;
+
+ /* save subdriver struct for suspend/resume wrappers */
+ info->subdriver = subdriver;
+
+err:
+ return rv;
+}
+
+static int qmi_wwan_bind(struct usbnet *dev, struct usb_interface *intf)
+{
+ int status = -1;
+ u8 *buf = intf->cur_altsetting->extra;
+ int len = intf->cur_altsetting->extralen;
+ struct usb_interface_descriptor *desc = &intf->cur_altsetting->desc;
+ struct usb_cdc_union_desc *cdc_union = NULL;
+ struct usb_cdc_ether_desc *cdc_ether = NULL;
+ u32 found = 0;
+ struct usb_driver *driver = driver_of(intf);
+ struct qmi_wwan_state *info = (void *)&dev->data;
+
+ BUILD_BUG_ON((sizeof(((struct usbnet *)0)->data) <
+ sizeof(struct qmi_wwan_state)));
+
+ /* set up initial state */
+ info->control = intf;
+ info->data = intf;
+
+ /* and a number of CDC descriptors */
+ while (len > 3) {
+ struct usb_descriptor_header *h = (void *)buf;
+
+ /* ignore any misplaced descriptors */
+ if (h->bDescriptorType != USB_DT_CS_INTERFACE)
+ goto next_desc;
+
+ /* buf[2] is CDC descriptor subtype */
+ switch (buf[2]) {
+ case USB_CDC_HEADER_TYPE:
+ if (found & 1 << USB_CDC_HEADER_TYPE) {
+ dev_dbg(&intf->dev, "extra CDC header\n");
+ goto err;
+ }
+ if (h->bLength != sizeof(struct usb_cdc_header_desc)) {
+ dev_dbg(&intf->dev, "CDC header len %u\n",
+ h->bLength);
+ goto err;
+ }
+ break;
+ case USB_CDC_UNION_TYPE:
+ if (found & 1 << USB_CDC_UNION_TYPE) {
+ dev_dbg(&intf->dev, "extra CDC union\n");
+ goto err;
+ }
+ if (h->bLength != sizeof(struct usb_cdc_union_desc)) {
+ dev_dbg(&intf->dev, "CDC union len %u\n",
+ h->bLength);
+ goto err;
+ }
+ cdc_union = (struct usb_cdc_union_desc *)buf;
+ break;
+ case USB_CDC_ETHERNET_TYPE:
+ if (found & 1 << USB_CDC_ETHERNET_TYPE) {
+ dev_dbg(&intf->dev, "extra CDC ether\n");
+ goto err;
+ }
+ if (h->bLength != sizeof(struct usb_cdc_ether_desc)) {
+ dev_dbg(&intf->dev, "CDC ether len %u\n",
+ h->bLength);
+ goto err;
+ }
+ cdc_ether = (struct usb_cdc_ether_desc *)buf;
+ break;
+ }
+
+ /* Remember which CDC functional descriptors we've seen. Works
+ * for all types we care about, of which USB_CDC_ETHERNET_TYPE
+ * (0x0f) is the highest numbered
+ */
+ if (buf[2] < 32)
+ found |= 1 << buf[2];
+
+next_desc:
+ len -= h->bLength;
+ buf += h->bLength;
+ }
+
+ /* Use separate control and data interfaces if we found a CDC Union */
+ if (cdc_union) {
+ info->data = usb_ifnum_to_if(dev->udev,
+ cdc_union->bSlaveInterface0);
+ if (desc->bInterfaceNumber != cdc_union->bMasterInterface0 ||
+ !info->data) {
+ dev_err(&intf->dev,
+ "bogus CDC Union: master=%u, slave=%u\n",
+ cdc_union->bMasterInterface0,
+ cdc_union->bSlaveInterface0);
+ goto err;
+ }
+ }
+
+ /* errors aren't fatal - we can live with the dynamic address */
+ if (cdc_ether) {
+ dev->hard_mtu = le16_to_cpu(cdc_ether->wMaxSegmentSize);
+ usbnet_get_ethernet_addr(dev, cdc_ether->iMACAddress);
+ }
+
+ /* claim data interface and set it up */
+ if (info->control != info->data) {
+ status = usb_driver_claim_interface(driver, info->data, dev);
+ if (status < 0)
+ goto err;
+ }
+
+ status = qmi_wwan_register_subdriver(dev);
+ if (status < 0 && info->control != info->data) {
+ usb_set_intfdata(info->data, NULL);
+ usb_driver_release_interface(driver, info->data);
+ }
+
+ /* Never use the same address on both ends of the link, even if the
+ * buggy firmware told us to. Or, if device is assigned the well-known
+ * buggy firmware MAC address, replace it with a random address,
+ */
+ if (ether_addr_equal(dev->net->dev_addr, default_modem_addr) ||
+ ether_addr_equal(dev->net->dev_addr, buggy_fw_addr))
+ eth_hw_addr_random(dev->net);
+
+ /* make MAC addr easily distinguishable from an IP header */
+ if (possibly_iphdr(dev->net->dev_addr)) {
+ dev->net->dev_addr[0] |= 0x02; /* set local assignment bit */
+ dev->net->dev_addr[0] &= 0xbf; /* clear "IP" bit */
+ }
+ dev->net->netdev_ops = &qmi_wwan_netdev_ops;
+err:
+ return status;
+}
+
+static void qmi_wwan_unbind(struct usbnet *dev, struct usb_interface *intf)
+{
+ struct qmi_wwan_state *info = (void *)&dev->data;
+ struct usb_driver *driver = driver_of(intf);
+ struct usb_interface *other;
+
+ if (info->subdriver && info->subdriver->disconnect)
+ info->subdriver->disconnect(info->control);
+
+ /* allow user to unbind using either control or data */
+ if (intf == info->control)
+ other = info->data;
+ else
+ other = info->control;
+
+ /* only if not shared */
+ if (other && intf != other) {
+ usb_set_intfdata(other, NULL);
+ usb_driver_release_interface(driver, other);
+ }
+
+ info->subdriver = NULL;
+ info->data = NULL;
+ info->control = NULL;
+}
+
+/* suspend/resume wrappers calling both usbnet and the cdc-wdm
+ * subdriver if present.
+ *
+ * NOTE: cdc-wdm also supports pre/post_reset, but we cannot provide
+ * wrappers for those without adding usbnet reset support first.
+ */
+static int qmi_wwan_suspend(struct usb_interface *intf, pm_message_t message)
+{
+ struct usbnet *dev = usb_get_intfdata(intf);
+ struct qmi_wwan_state *info = (void *)&dev->data;
+ int ret;
+
+ /* Both usbnet_suspend() and subdriver->suspend() MUST return 0
+ * in system sleep context, otherwise, the resume callback has
+ * to recover device from previous suspend failure.
+ */
+ ret = usbnet_suspend(intf, message);
+ if (ret < 0)
+ goto err;
+
+ if (intf == info->control && info->subdriver &&
+ info->subdriver->suspend)
+ ret = info->subdriver->suspend(intf, message);
+ if (ret < 0)
+ usbnet_resume(intf);
+err:
+ return ret;
+}
+
+static int qmi_wwan_resume(struct usb_interface *intf)
+{
+ struct usbnet *dev = usb_get_intfdata(intf);
+ struct qmi_wwan_state *info = (void *)&dev->data;
+ int ret = 0;
+ bool callsub = (intf == info->control && info->subdriver &&
+ info->subdriver->resume);
+
+ if (callsub)
+ ret = info->subdriver->resume(intf);
+ if (ret < 0)
+ goto err;
+ ret = usbnet_resume(intf);
+ if (ret < 0 && callsub)
+ info->subdriver->suspend(intf, PMSG_SUSPEND);
+err:
+ return ret;
+}
+
+static const struct driver_info qmi_wwan_info = {
+ .description = "WWAN/QMI device",
+ .flags = FLAG_WWAN,
+ .bind = qmi_wwan_bind,
+ .unbind = qmi_wwan_unbind,
+ .manage_power = qmi_wwan_manage_power,
+ .rx_fixup = qmi_wwan_rx_fixup,
+};
+
+#define HUAWEI_VENDOR_ID 0x12D1
+
+/* map QMI/wwan function by a fixed interface number */
+#define QMI_FIXED_INTF(vend, prod, num) \
+ USB_DEVICE_INTERFACE_NUMBER(vend, prod, num), \
+ .driver_info = (unsigned long)&qmi_wwan_info
+
+/* Gobi 1000 QMI/wwan interface number is 3 according to qcserial */
+#define QMI_GOBI1K_DEVICE(vend, prod) \
+ QMI_FIXED_INTF(vend, prod, 3)
+
+/* Gobi 2000/3000 QMI/wwan interface number is 0 according to qcserial */
+#define QMI_GOBI_DEVICE(vend, prod) \
+ QMI_FIXED_INTF(vend, prod, 0)
+
+static const struct usb_device_id products[] = {
+ /* 1. CDC ECM like devices match on the control interface */
+ { /* Huawei E392, E398 and possibly others sharing both device id and more... */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 9),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Vodafone/Huawei K5005 (12d1:14c8) and similar modems */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 57),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* HUAWEI_INTERFACE_NDIS_CONTROL_QUALCOMM */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 0x01, 0x69),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+
+ /* 2. Combined interface devices matching on class+protocol */
+ { /* Huawei E367 and possibly others in "Windows mode" */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 7),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Huawei E392, E398 and possibly others in "Windows mode" */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 1, 17),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* HUAWEI_NDIS_SINGLE_INTERFACE_VDF */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 0x01, 0x37),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* HUAWEI_INTERFACE_NDIS_HW_QUALCOMM */
+ USB_VENDOR_AND_INTERFACE_INFO(HUAWEI_VENDOR_ID, USB_CLASS_VENDOR_SPEC, 0x01, 0x67),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Pantech UML290, P4200 and more */
+ USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf0, 0xff),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Pantech UML290 - newer firmware */
+ USB_VENDOR_AND_INTERFACE_INFO(0x106c, USB_CLASS_VENDOR_SPEC, 0xf1, 0xff),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Novatel USB551L and MC551 */
+ USB_DEVICE_AND_INTERFACE_INFO(0x1410, 0xb001,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Novatel E362 */
+ USB_DEVICE_AND_INTERFACE_INFO(0x1410, 0x9010,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Novatel Expedite E371 */
+ USB_DEVICE_AND_INTERFACE_INFO(0x1410, 0x9011,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Dell Wireless 5800 (Novatel E362) */
+ USB_DEVICE_AND_INTERFACE_INFO(0x413C, 0x8195,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Dell Wireless 5800 V2 (Novatel E362) */
+ USB_DEVICE_AND_INTERFACE_INFO(0x413C, 0x8196,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* Dell Wireless 5804 (Novatel E371) */
+ USB_DEVICE_AND_INTERFACE_INFO(0x413C, 0x819b,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+ { /* ADU960S */
+ USB_DEVICE_AND_INTERFACE_INFO(0x16d5, 0x650a,
+ USB_CLASS_COMM,
+ USB_CDC_SUBCLASS_ETHERNET,
+ USB_CDC_PROTO_NONE),
+ .driver_info = (unsigned long)&qmi_wwan_info,
+ },
+
+ /* 3. Combined interface devices matching on interface number */
+ {QMI_FIXED_INTF(0x0408, 0xea42, 4)}, /* Yota / Megafon M100-1 */
+ {QMI_FIXED_INTF(0x05c6, 0x7000, 0)},
+ {QMI_FIXED_INTF(0x05c6, 0x7001, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x7002, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x7101, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x7101, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x7101, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x7102, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x7102, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x7102, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x8000, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x8001, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9000, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9003, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9005, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x900a, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x900b, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x900c, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x900c, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x900c, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x900d, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x900f, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x900f, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x900f, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9010, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9010, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9011, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9011, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9021, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x9022, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x9025, 4)}, /* Alcatel-sbell ASB TL131 TDD LTE (China Mobile) */
+ {QMI_FIXED_INTF(0x05c6, 0x9026, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x902e, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9031, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9032, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9033, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9033, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9033, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9033, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9034, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9034, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9034, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9034, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9034, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9035, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9036, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9037, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9038, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x903b, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x903c, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x903d, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x903e, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9043, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9046, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9046, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9046, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9047, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x9047, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9047, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9048, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9048, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9048, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9048, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9048, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x904c, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x904c, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x904c, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x904c, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9050, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9052, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9053, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9053, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9054, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9054, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9055, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9055, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9055, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9055, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9055, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9056, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9062, 9)},
+ {QMI_FIXED_INTF(0x05c6, 0x9064, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9065, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9065, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9066, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9066, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9067, 1)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 2)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9068, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9069, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9069, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9069, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9069, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9070, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9070, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9075, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9076, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9076, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9076, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9076, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9076, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9077, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9077, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9077, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9077, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9078, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9079, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x9079, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9079, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9079, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9079, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9080, 5)},
+ {QMI_FIXED_INTF(0x05c6, 0x9080, 6)},
+ {QMI_FIXED_INTF(0x05c6, 0x9080, 7)},
+ {QMI_FIXED_INTF(0x05c6, 0x9080, 8)},
+ {QMI_FIXED_INTF(0x05c6, 0x9083, 3)},
+ {QMI_FIXED_INTF(0x05c6, 0x9084, 4)},
+ {QMI_FIXED_INTF(0x05c6, 0x920d, 0)},
+ {QMI_FIXED_INTF(0x05c6, 0x920d, 5)},
+ {QMI_FIXED_INTF(0x0846, 0x68a2, 8)},
+ {QMI_FIXED_INTF(0x12d1, 0x140c, 1)}, /* Huawei E173 */
+ {QMI_FIXED_INTF(0x12d1, 0x14ac, 1)}, /* Huawei E1820 */
+ {QMI_FIXED_INTF(0x16d8, 0x6003, 0)}, /* CMOTech 6003 */
+ {QMI_FIXED_INTF(0x16d8, 0x6007, 0)}, /* CMOTech CHE-628S */
+ {QMI_FIXED_INTF(0x16d8, 0x6008, 0)}, /* CMOTech CMU-301 */
+ {QMI_FIXED_INTF(0x16d8, 0x6280, 0)}, /* CMOTech CHU-628 */
+ {QMI_FIXED_INTF(0x16d8, 0x7001, 0)}, /* CMOTech CHU-720S */
+ {QMI_FIXED_INTF(0x16d8, 0x7002, 0)}, /* CMOTech 7002 */
+ {QMI_FIXED_INTF(0x16d8, 0x7003, 4)}, /* CMOTech CHU-629K */
+ {QMI_FIXED_INTF(0x16d8, 0x7004, 3)}, /* CMOTech 7004 */
+ {QMI_FIXED_INTF(0x16d8, 0x7006, 5)}, /* CMOTech CGU-629 */
+ {QMI_FIXED_INTF(0x16d8, 0x700a, 4)}, /* CMOTech CHU-629S */
+ {QMI_FIXED_INTF(0x16d8, 0x7211, 0)}, /* CMOTech CHU-720I */
+ {QMI_FIXED_INTF(0x16d8, 0x7212, 0)}, /* CMOTech 7212 */
+ {QMI_FIXED_INTF(0x16d8, 0x7213, 0)}, /* CMOTech 7213 */
+ {QMI_FIXED_INTF(0x16d8, 0x7251, 1)}, /* CMOTech 7251 */
+ {QMI_FIXED_INTF(0x16d8, 0x7252, 1)}, /* CMOTech 7252 */
+ {QMI_FIXED_INTF(0x16d8, 0x7253, 1)}, /* CMOTech 7253 */
+ {QMI_FIXED_INTF(0x19d2, 0x0002, 1)},
+ {QMI_FIXED_INTF(0x19d2, 0x0012, 1)},
+ {QMI_FIXED_INTF(0x19d2, 0x0017, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x0019, 3)}, /* ONDA MT689DC */
+ {QMI_FIXED_INTF(0x19d2, 0x0021, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0025, 1)},
+ {QMI_FIXED_INTF(0x19d2, 0x0031, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0042, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0049, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0052, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0055, 1)}, /* ZTE (Vodafone) K3520-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x0058, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0063, 4)}, /* ZTE (Vodafone) K3565-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x0104, 4)}, /* ZTE (Vodafone) K4505-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x0113, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0118, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0121, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0123, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0124, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0125, 6)},
+ {QMI_FIXED_INTF(0x19d2, 0x0126, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0130, 1)},
+ {QMI_FIXED_INTF(0x19d2, 0x0133, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x0141, 5)},
+ {QMI_FIXED_INTF(0x19d2, 0x0157, 5)}, /* ZTE MF683 */
+ {QMI_FIXED_INTF(0x19d2, 0x0158, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x0167, 4)}, /* ZTE MF820D */
+ {QMI_FIXED_INTF(0x19d2, 0x0168, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x0176, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x0178, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x0191, 4)}, /* ZTE EuFi890 */
+ {QMI_FIXED_INTF(0x19d2, 0x0199, 1)}, /* ZTE MF820S */
+ {QMI_FIXED_INTF(0x19d2, 0x0200, 1)},
+ {QMI_FIXED_INTF(0x19d2, 0x0257, 3)}, /* ZTE MF821 */
+ {QMI_FIXED_INTF(0x19d2, 0x0265, 4)}, /* ONDA MT8205 4G LTE */
+ {QMI_FIXED_INTF(0x19d2, 0x0284, 4)}, /* ZTE MF880 */
+ {QMI_FIXED_INTF(0x19d2, 0x0326, 4)}, /* ZTE MF821D */
+ {QMI_FIXED_INTF(0x19d2, 0x0412, 4)}, /* Telewell TW-LTE 4G */
+ {QMI_FIXED_INTF(0x19d2, 0x1008, 4)}, /* ZTE (Vodafone) K3570-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x1010, 4)}, /* ZTE (Vodafone) K3571-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x1012, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1018, 3)}, /* ZTE (Vodafone) K5006-Z */
+ {QMI_FIXED_INTF(0x19d2, 0x1021, 2)},
+ {QMI_FIXED_INTF(0x19d2, 0x1245, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1247, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1252, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1254, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1255, 3)},
+ {QMI_FIXED_INTF(0x19d2, 0x1255, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1256, 4)},
+ {QMI_FIXED_INTF(0x19d2, 0x1270, 5)}, /* ZTE MF667 */
+ {QMI_FIXED_INTF(0x19d2, 0x1401, 2)},
+ {QMI_FIXED_INTF(0x19d2, 0x1402, 2)}, /* ZTE MF60 */
+ {QMI_FIXED_INTF(0x19d2, 0x1424, 2)},
+ {QMI_FIXED_INTF(0x19d2, 0x1425, 2)},
+ {QMI_FIXED_INTF(0x19d2, 0x1426, 2)}, /* ZTE MF91 */
+ {QMI_FIXED_INTF(0x19d2, 0x1428, 2)}, /* Telewell TW-LTE 4G v2 */
+ {QMI_FIXED_INTF(0x19d2, 0x2002, 4)}, /* ZTE (Vodafone) K3765-Z */
+ {QMI_FIXED_INTF(0x0f3d, 0x68a2, 8)}, /* Sierra Wireless MC7700 */
+ {QMI_FIXED_INTF(0x114f, 0x68a2, 8)}, /* Sierra Wireless MC7750 */
+ {QMI_FIXED_INTF(0x1199, 0x68a2, 8)}, /* Sierra Wireless MC7710 in QMI mode */
+ {QMI_FIXED_INTF(0x1199, 0x68a2, 19)}, /* Sierra Wireless MC7710 in QMI mode */
+ {QMI_FIXED_INTF(0x1199, 0x68c0, 8)}, /* Sierra Wireless MC73xx */
+ {QMI_FIXED_INTF(0x1199, 0x68c0, 10)}, /* Sierra Wireless MC73xx */
+ {QMI_FIXED_INTF(0x1199, 0x901c, 8)}, /* Sierra Wireless EM7700 */
+ {QMI_FIXED_INTF(0x1199, 0x901f, 8)}, /* Sierra Wireless EM7355 */
+ {QMI_FIXED_INTF(0x1199, 0x9041, 8)}, /* Sierra Wireless MC7305/MC7355 */
+ {QMI_FIXED_INTF(0x1199, 0x9051, 8)}, /* Netgear AirCard 340U */
+ {QMI_FIXED_INTF(0x1199, 0x9053, 8)}, /* Sierra Wireless Modem */
+ {QMI_FIXED_INTF(0x1199, 0x9054, 8)}, /* Sierra Wireless Modem */
+ {QMI_FIXED_INTF(0x1199, 0x9055, 8)}, /* Netgear AirCard 341U */
+ {QMI_FIXED_INTF(0x1199, 0x9056, 8)}, /* Sierra Wireless Modem */
+ {QMI_FIXED_INTF(0x1199, 0x9057, 8)},
+ {QMI_FIXED_INTF(0x1199, 0x9061, 8)}, /* Sierra Wireless Modem */
+ {QMI_FIXED_INTF(0x1bbb, 0x011e, 4)}, /* Telekom Speedstick LTE II (Alcatel One Touch L100V LTE) */
+ {QMI_FIXED_INTF(0x1bbb, 0x0203, 2)}, /* Alcatel L800MA */
+ {QMI_FIXED_INTF(0x2357, 0x0201, 4)}, /* TP-LINK HSUPA Modem MA180 */
+ {QMI_FIXED_INTF(0x2357, 0x9000, 4)}, /* TP-LINK MA260 */
+ {QMI_FIXED_INTF(0x1bc7, 0x1200, 5)}, /* Telit LE920 */
+ {QMI_FIXED_INTF(0x1bc7, 0x1201, 2)}, /* Telit LE920 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc000, 4)}, /* Olivetti Olicard 100 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc001, 4)}, /* Olivetti Olicard 120 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc002, 4)}, /* Olivetti Olicard 140 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc004, 6)}, /* Olivetti Olicard 155 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc005, 6)}, /* Olivetti Olicard 200 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc00a, 6)}, /* Olivetti Olicard 160 */
+ {QMI_FIXED_INTF(0x0b3c, 0xc00b, 4)}, /* Olivetti Olicard 500 */
+ {QMI_FIXED_INTF(0x1e2d, 0x0060, 4)}, /* Cinterion PLxx */
+ {QMI_FIXED_INTF(0x1e2d, 0x0053, 4)}, /* Cinterion PHxx,PXxx */
+ {QMI_FIXED_INTF(0x413c, 0x81a2, 8)}, /* Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card */
+ {QMI_FIXED_INTF(0x413c, 0x81a3, 8)}, /* Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card */
+ {QMI_FIXED_INTF(0x413c, 0x81a4, 8)}, /* Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card */
+ {QMI_FIXED_INTF(0x413c, 0x81a8, 8)}, /* Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card */
+ {QMI_FIXED_INTF(0x413c, 0x81a9, 8)}, /* Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card */
+ {QMI_FIXED_INTF(0x03f0, 0x581d, 4)}, /* HP lt4112 LTE/HSPA+ Gobi 4G Module (Huawei me906e) */
+
+ /* 4. Gobi 1000 devices */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9212)}, /* Acer Gobi Modem Device */
+ {QMI_GOBI1K_DEVICE(0x03f0, 0x1f1d)}, /* HP un2400 Gobi Modem Device */
+ {QMI_GOBI1K_DEVICE(0x04da, 0x250d)}, /* Panasonic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x413c, 0x8172)}, /* Dell Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa001)}, /* Novatel/Verizon USB-1000 */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa002)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa003)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa004)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa005)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa006)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x1410, 0xa007)}, /* Novatel Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x0b05, 0x1776)}, /* Asus Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x19d2, 0xfff3)}, /* ONDA Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9001)}, /* Generic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9002)}, /* Generic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9202)}, /* Generic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9203)}, /* Generic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9222)}, /* Generic Gobi Modem device */
+ {QMI_GOBI1K_DEVICE(0x05c6, 0x9009)}, /* Generic Gobi Modem device */
+
+ /* 5. Gobi 2000 and 3000 devices */
+ {QMI_GOBI_DEVICE(0x413c, 0x8186)}, /* Dell Gobi 2000 Modem device (N0218, VU936) */
+ {QMI_GOBI_DEVICE(0x413c, 0x8194)}, /* Dell Gobi 3000 Composite */
+ {QMI_GOBI_DEVICE(0x05c6, 0x920b)}, /* Generic Gobi 2000 Modem device */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9225)}, /* Sony Gobi 2000 Modem device (N0279, VU730) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9245)}, /* Samsung Gobi 2000 Modem device (VL176) */
+ {QMI_GOBI_DEVICE(0x03f0, 0x251d)}, /* HP Gobi 2000 Modem device (VP412) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9215)}, /* Acer Gobi 2000 Modem device (VP413) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9265)}, /* Asus Gobi 2000 Modem device (VR305) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9235)}, /* Top Global Gobi 2000 Modem device (VR306) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9275)}, /* iRex Technologies Gobi 2000 Modem device (VR307) */
+ {QMI_GOBI_DEVICE(0x0af0, 0x8120)}, /* Option GTM681W */
+ {QMI_GOBI_DEVICE(0x1199, 0x68a5)}, /* Sierra Wireless Modem */
+ {QMI_GOBI_DEVICE(0x1199, 0x68a9)}, /* Sierra Wireless Modem */
+ {QMI_GOBI_DEVICE(0x1199, 0x9001)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9002)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9003)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9004)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9005)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9006)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9007)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9008)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9009)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x900a)}, /* Sierra Wireless Gobi 2000 Modem device (VT773) */
+ {QMI_GOBI_DEVICE(0x1199, 0x9011)}, /* Sierra Wireless Gobi 2000 Modem device (MC8305) */
+ {QMI_GOBI_DEVICE(0x16d8, 0x8002)}, /* CMDTech Gobi 2000 Modem device (VU922) */
+ {QMI_GOBI_DEVICE(0x05c6, 0x9205)}, /* Gobi 2000 Modem device */
+ {QMI_GOBI_DEVICE(0x1199, 0x9013)}, /* Sierra Wireless Gobi 3000 Modem device (MC8355) */
+ {QMI_GOBI_DEVICE(0x03f0, 0x371d)}, /* HP un2430 Mobile Broadband Module */
+ {QMI_GOBI_DEVICE(0x1199, 0x9015)}, /* Sierra Wireless Gobi 3000 Modem device */
+ {QMI_GOBI_DEVICE(0x1199, 0x9019)}, /* Sierra Wireless Gobi 3000 Modem device */
+ {QMI_GOBI_DEVICE(0x1199, 0x901b)}, /* Sierra Wireless MC7770 */
+ {QMI_GOBI_DEVICE(0x12d1, 0x14f1)}, /* Sony Gobi 3000 Composite */
+ {QMI_GOBI_DEVICE(0x1410, 0xa021)}, /* Foxconn Gobi 3000 Modem device (Novatel E396) */
+
+ { } /* END */
+};
+MODULE_DEVICE_TABLE(usb, products);
+
+static int qmi_wwan_probe(struct usb_interface *intf,
+ const struct usb_device_id *prod)
+{
+ struct usb_device_id *id = (struct usb_device_id *)prod;
+
+ /* Workaround to enable dynamic IDs. This disables usbnet
+ * blacklisting functionality. Which, if required, can be
+ * reimplemented here by using a magic "blacklist" value
+ * instead of 0 in the static device id table
+ */
+ if (!id->driver_info) {
+ dev_dbg(&intf->dev, "setting defaults for dynamic device id\n");
+ id->driver_info = (unsigned long)&qmi_wwan_info;
+ }
+
+ return usbnet_probe(intf, id);
+}
+
+static struct usb_driver qmi_wwan_driver = {
+ .name = "qmi_wwan",
+ .id_table = products,
+ .probe = qmi_wwan_probe,
+ .disconnect = usbnet_disconnect,
+ .suspend = qmi_wwan_suspend,
+ .resume = qmi_wwan_resume,
+ .reset_resume = qmi_wwan_resume,
+ .supports_autosuspend = 1,
+ .disable_hub_initiated_lpm = 1,
+};
+
+module_usb_driver(qmi_wwan_driver);
+
+MODULE_AUTHOR("Bjørn Mork <bjorn@mork.no>");
+MODULE_DESCRIPTION("Qualcomm MSM Interface (QMI) WWAN driver");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff