--- /dev/null
+/*
+ * Davicom DM96xx USB 10/100Mbps ethernet devices
+ *
+ * Peter Korsgaard <jacmet@sunsite.dk>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+//#define DEBUG
+
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/stddef.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/usb.h>
+#include <linux/crc32.h>
+#include <linux/usb/usbnet.h>
+#include <linux/slab.h>
+
+/* datasheet:
+ http://ptm2.cc.utu.fi/ftp/network/cards/DM9601/From_NET/DM9601-DS-P01-930914.pdf
+*/
+
+/* control requests */
+#define DM_READ_REGS 0x00
+#define DM_WRITE_REGS 0x01
+#define DM_READ_MEMS 0x02
+#define DM_WRITE_REG 0x03
+#define DM_WRITE_MEMS 0x05
+#define DM_WRITE_MEM 0x07
+
+/* registers */
+#define DM_NET_CTRL 0x00
+#define DM_RX_CTRL 0x05
+#define DM_SHARED_CTRL 0x0b
+#define DM_SHARED_ADDR 0x0c
+#define DM_SHARED_DATA 0x0d /* low + high */
+#define DM_PHY_ADDR 0x10 /* 6 bytes */
+#define DM_MCAST_ADDR 0x16 /* 8 bytes */
+#define DM_GPR_CTRL 0x1e
+#define DM_GPR_DATA 0x1f
+#define DM_CHIP_ID 0x2c
+#define DM_MODE_CTRL 0x91 /* only on dm9620 */
+
+/* chip id values */
+#define ID_DM9601 0
+#define ID_DM9620 1
+
+#define DM_MAX_MCAST 64
+#define DM_MCAST_SIZE 8
+#define DM_EEPROM_LEN 256
+#define DM_TX_OVERHEAD 2 /* 2 byte header */
+#define DM_RX_OVERHEAD 7 /* 3 byte header + 4 byte crc tail */
+#define DM_TIMEOUT 1000
+
+static int dm_read(struct usbnet *dev, u8 reg, u16 length, void *data)
+{
+ int err;
+ err = usbnet_read_cmd(dev, DM_READ_REGS,
+ USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ 0, reg, data, length);
+ if(err != length && err >= 0)
+ err = -EINVAL;
+ return err;
+}
+
+static int dm_read_reg(struct usbnet *dev, u8 reg, u8 *value)
+{
+ return dm_read(dev, reg, 1, value);
+}
+
+static int dm_write(struct usbnet *dev, u8 reg, u16 length, void *data)
+{
+ int err;
+ err = usbnet_write_cmd(dev, DM_WRITE_REGS,
+ USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ 0, reg, data, length);
+
+ if (err >= 0 && err < length)
+ err = -EINVAL;
+ return err;
+}
+
+static int dm_write_reg(struct usbnet *dev, u8 reg, u8 value)
+{
+ return usbnet_write_cmd(dev, DM_WRITE_REG,
+ USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ value, reg, NULL, 0);
+}
+
+static void dm_write_async(struct usbnet *dev, u8 reg, u16 length, void *data)
+{
+ usbnet_write_cmd_async(dev, DM_WRITE_REGS,
+ USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ 0, reg, data, length);
+}
+
+static void dm_write_reg_async(struct usbnet *dev, u8 reg, u8 value)
+{
+ usbnet_write_cmd_async(dev, DM_WRITE_REG,
+ USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ value, reg, NULL, 0);
+}
+
+static int dm_read_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 *value)
+{
+ int ret, i;
+
+ mutex_lock(&dev->phy_mutex);
+
+ dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg);
+ dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0xc : 0x4);
+
+ for (i = 0; i < DM_TIMEOUT; i++) {
+ u8 tmp = 0;
+
+ udelay(1);
+ ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp);
+ if (ret < 0)
+ goto out;
+
+ /* ready */
+ if ((tmp & 1) == 0)
+ break;
+ }
+
+ if (i == DM_TIMEOUT) {
+ netdev_err(dev->net, "%s read timed out!\n", phy ? "phy" : "eeprom");
+ ret = -EIO;
+ goto out;
+ }
+
+ dm_write_reg(dev, DM_SHARED_CTRL, 0x0);
+ ret = dm_read(dev, DM_SHARED_DATA, 2, value);
+
+ netdev_dbg(dev->net, "read shared %d 0x%02x returned 0x%04x, %d\n",
+ phy, reg, *value, ret);
+
+ out:
+ mutex_unlock(&dev->phy_mutex);
+ return ret;
+}
+
+static int dm_write_shared_word(struct usbnet *dev, int phy, u8 reg, __le16 value)
+{
+ int ret, i;
+
+ mutex_lock(&dev->phy_mutex);
+
+ ret = dm_write(dev, DM_SHARED_DATA, 2, &value);
+ if (ret < 0)
+ goto out;
+
+ dm_write_reg(dev, DM_SHARED_ADDR, phy ? (reg | 0x40) : reg);
+ dm_write_reg(dev, DM_SHARED_CTRL, phy ? 0x1a : 0x12);
+
+ for (i = 0; i < DM_TIMEOUT; i++) {
+ u8 tmp = 0;
+
+ udelay(1);
+ ret = dm_read_reg(dev, DM_SHARED_CTRL, &tmp);
+ if (ret < 0)
+ goto out;
+
+ /* ready */
+ if ((tmp & 1) == 0)
+ break;
+ }
+
+ if (i == DM_TIMEOUT) {
+ netdev_err(dev->net, "%s write timed out!\n", phy ? "phy" : "eeprom");
+ ret = -EIO;
+ goto out;
+ }
+
+ dm_write_reg(dev, DM_SHARED_CTRL, 0x0);
+
+out:
+ mutex_unlock(&dev->phy_mutex);
+ return ret;
+}
+
+static int dm_read_eeprom_word(struct usbnet *dev, u8 offset, void *value)
+{
+ return dm_read_shared_word(dev, 0, offset, value);
+}
+
+
+
+static int dm9601_get_eeprom_len(struct net_device *dev)
+{
+ return DM_EEPROM_LEN;
+}
+
+static int dm9601_get_eeprom(struct net_device *net,
+ struct ethtool_eeprom *eeprom, u8 * data)
+{
+ struct usbnet *dev = netdev_priv(net);
+ __le16 *ebuf = (__le16 *) data;
+ int i;
+
+ /* access is 16bit */
+ if ((eeprom->offset % 2) || (eeprom->len % 2))
+ return -EINVAL;
+
+ for (i = 0; i < eeprom->len / 2; i++) {
+ if (dm_read_eeprom_word(dev, eeprom->offset / 2 + i,
+ &ebuf[i]) < 0)
+ return -EINVAL;
+ }
+ return 0;
+}
+
+static int dm9601_mdio_read(struct net_device *netdev, int phy_id, int loc)
+{
+ struct usbnet *dev = netdev_priv(netdev);
+
+ __le16 res;
+
+ if (phy_id) {
+ netdev_dbg(dev->net, "Only internal phy supported\n");
+ return 0;
+ }
+
+ dm_read_shared_word(dev, 1, loc, &res);
+
+ netdev_dbg(dev->net,
+ "dm9601_mdio_read() phy_id=0x%02x, loc=0x%02x, returns=0x%04x\n",
+ phy_id, loc, le16_to_cpu(res));
+
+ return le16_to_cpu(res);
+}
+
+static void dm9601_mdio_write(struct net_device *netdev, int phy_id, int loc,
+ int val)
+{
+ struct usbnet *dev = netdev_priv(netdev);
+ __le16 res = cpu_to_le16(val);
+
+ if (phy_id) {
+ netdev_dbg(dev->net, "Only internal phy supported\n");
+ return;
+ }
+
+ netdev_dbg(dev->net, "dm9601_mdio_write() phy_id=0x%02x, loc=0x%02x, val=0x%04x\n",
+ phy_id, loc, val);
+
+ dm_write_shared_word(dev, 1, loc, res);
+}
+
+static void dm9601_get_drvinfo(struct net_device *net,
+ struct ethtool_drvinfo *info)
+{
+ /* Inherit standard device info */
+ usbnet_get_drvinfo(net, info);
+ info->eedump_len = DM_EEPROM_LEN;
+}
+
+static u32 dm9601_get_link(struct net_device *net)
+{
+ struct usbnet *dev = netdev_priv(net);
+
+ return mii_link_ok(&dev->mii);
+}
+
+static int dm9601_ioctl(struct net_device *net, struct ifreq *rq, int cmd)
+{
+ struct usbnet *dev = netdev_priv(net);
+
+ return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL);
+}
+
+static const struct ethtool_ops dm9601_ethtool_ops = {
+ .get_drvinfo = dm9601_get_drvinfo,
+ .get_link = dm9601_get_link,
+ .get_msglevel = usbnet_get_msglevel,
+ .set_msglevel = usbnet_set_msglevel,
+ .get_eeprom_len = dm9601_get_eeprom_len,
+ .get_eeprom = dm9601_get_eeprom,
+ .get_settings = usbnet_get_settings,
+ .set_settings = usbnet_set_settings,
+ .nway_reset = usbnet_nway_reset,
+};
+
+static void dm9601_set_multicast(struct net_device *net)
+{
+ struct usbnet *dev = netdev_priv(net);
+ /* We use the 20 byte dev->data for our 8 byte filter buffer
+ * to avoid allocating memory that is tricky to free later */
+ u8 *hashes = (u8 *) & dev->data;
+ u8 rx_ctl = 0x31;
+
+ memset(hashes, 0x00, DM_MCAST_SIZE);
+ hashes[DM_MCAST_SIZE - 1] |= 0x80; /* broadcast address */
+
+ if (net->flags & IFF_PROMISC) {
+ rx_ctl |= 0x02;
+ } else if (net->flags & IFF_ALLMULTI ||
+ netdev_mc_count(net) > DM_MAX_MCAST) {
+ rx_ctl |= 0x08;
+ } else if (!netdev_mc_empty(net)) {
+ struct netdev_hw_addr *ha;
+
+ netdev_for_each_mc_addr(ha, net) {
+ u32 crc = ether_crc(ETH_ALEN, ha->addr) >> 26;
+ hashes[crc >> 3] |= 1 << (crc & 0x7);
+ }
+ }
+
+ dm_write_async(dev, DM_MCAST_ADDR, DM_MCAST_SIZE, hashes);
+ dm_write_reg_async(dev, DM_RX_CTRL, rx_ctl);
+}
+
+static void __dm9601_set_mac_address(struct usbnet *dev)
+{
+ dm_write_async(dev, DM_PHY_ADDR, ETH_ALEN, dev->net->dev_addr);
+}
+
+static int dm9601_set_mac_address(struct net_device *net, void *p)
+{
+ struct sockaddr *addr = p;
+ struct usbnet *dev = netdev_priv(net);
+
+ if (!is_valid_ether_addr(addr->sa_data)) {
+ dev_err(&net->dev, "not setting invalid mac address %pM\n",
+ addr->sa_data);
+ return -EINVAL;
+ }
+
+ memcpy(net->dev_addr, addr->sa_data, net->addr_len);
+ __dm9601_set_mac_address(dev);
+
+ return 0;
+}
+
+static const struct net_device_ops dm9601_netdev_ops = {
+ .ndo_open = usbnet_open,
+ .ndo_stop = usbnet_stop,
+ .ndo_start_xmit = usbnet_start_xmit,
+ .ndo_tx_timeout = usbnet_tx_timeout,
+ .ndo_change_mtu = usbnet_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_do_ioctl = dm9601_ioctl,
+ .ndo_set_rx_mode = dm9601_set_multicast,
+ .ndo_set_mac_address = dm9601_set_mac_address,
+};
+
+static int dm9601_bind(struct usbnet *dev, struct usb_interface *intf)
+{
+ int ret;
+ u8 mac[ETH_ALEN], id;
+
+ ret = usbnet_get_endpoints(dev, intf);
+ if (ret)
+ goto out;
+
+ dev->net->netdev_ops = &dm9601_netdev_ops;
+ dev->net->ethtool_ops = &dm9601_ethtool_ops;
+ dev->net->hard_header_len += DM_TX_OVERHEAD;
+ dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len;
+
+ /* dm9620/21a require room for 4 byte padding, even in dm9601
+ * mode, so we need +1 to be able to receive full size
+ * ethernet frames.
+ */
+ dev->rx_urb_size = dev->net->mtu + ETH_HLEN + DM_RX_OVERHEAD + 1;
+
+ dev->mii.dev = dev->net;
+ dev->mii.mdio_read = dm9601_mdio_read;
+ dev->mii.mdio_write = dm9601_mdio_write;
+ dev->mii.phy_id_mask = 0x1f;
+ dev->mii.reg_num_mask = 0x1f;
+
+ /* reset */
+ dm_write_reg(dev, DM_NET_CTRL, 1);
+ udelay(20);
+
+ /* read MAC */
+ if (dm_read(dev, DM_PHY_ADDR, ETH_ALEN, mac) < 0) {
+ printk(KERN_ERR "Error reading MAC address\n");
+ ret = -ENODEV;
+ goto out;
+ }
+
+ /*
+ * Overwrite the auto-generated address only with good ones.
+ */
+ if (is_valid_ether_addr(mac))
+ memcpy(dev->net->dev_addr, mac, ETH_ALEN);
+ else {
+ printk(KERN_WARNING
+ "dm9601: No valid MAC address in EEPROM, using %pM\n",
+ dev->net->dev_addr);
+ __dm9601_set_mac_address(dev);
+ }
+
+ if (dm_read_reg(dev, DM_CHIP_ID, &id) < 0) {
+ netdev_err(dev->net, "Error reading chip ID\n");
+ ret = -ENODEV;
+ goto out;
+ }
+
+ /* put dm9620 devices in dm9601 mode */
+ if (id == ID_DM9620) {
+ u8 mode;
+
+ if (dm_read_reg(dev, DM_MODE_CTRL, &mode) < 0) {
+ netdev_err(dev->net, "Error reading MODE_CTRL\n");
+ ret = -ENODEV;
+ goto out;
+ }
+ dm_write_reg(dev, DM_MODE_CTRL, mode & 0x7f);
+ }
+
+ /* power up phy */
+ dm_write_reg(dev, DM_GPR_CTRL, 1);
+ dm_write_reg(dev, DM_GPR_DATA, 0);
+
+ /* receive broadcast packets */
+ dm9601_set_multicast(dev->net);
+
+ dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET);
+ dm9601_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE,
+ ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP);
+ mii_nway_restart(&dev->mii);
+
+out:
+ return ret;
+}
+
+static int dm9601_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
+{
+ u8 status;
+ int len;
+
+ /* format:
+ b1: rx status
+ b2: packet length (incl crc) low
+ b3: packet length (incl crc) high
+ b4..n-4: packet data
+ bn-3..bn: ethernet crc
+ */
+
+ if (unlikely(skb->len < DM_RX_OVERHEAD)) {
+ dev_err(&dev->udev->dev, "unexpected tiny rx frame\n");
+ return 0;
+ }
+
+ status = skb->data[0];
+ len = (skb->data[1] | (skb->data[2] << 8)) - 4;
+
+ if (unlikely(status & 0xbf)) {
+ if (status & 0x01) dev->net->stats.rx_fifo_errors++;
+ if (status & 0x02) dev->net->stats.rx_crc_errors++;
+ if (status & 0x04) dev->net->stats.rx_frame_errors++;
+ if (status & 0x20) dev->net->stats.rx_missed_errors++;
+ if (status & 0x90) dev->net->stats.rx_length_errors++;
+ return 0;
+ }
+
+ skb_pull(skb, 3);
+ skb_trim(skb, len);
+
+ return 1;
+}
+
+static struct sk_buff *dm9601_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
+ gfp_t flags)
+{
+ int len, pad;
+
+ /* format:
+ b1: packet length low
+ b2: packet length high
+ b3..n: packet data
+ */
+
+ len = skb->len + DM_TX_OVERHEAD;
+
+ /* workaround for dm962x errata with tx fifo getting out of
+ * sync if a USB bulk transfer retry happens right after a
+ * packet with odd / maxpacket length by adding up to 3 bytes
+ * padding.
+ */
+ while ((len & 1) || !(len % dev->maxpacket))
+ len++;
+
+ len -= DM_TX_OVERHEAD; /* hw header doesn't count as part of length */
+ pad = len - skb->len;
+
+ if (skb_headroom(skb) < DM_TX_OVERHEAD || skb_tailroom(skb) < pad) {
+ struct sk_buff *skb2;
+
+ skb2 = skb_copy_expand(skb, DM_TX_OVERHEAD, pad, flags);
+ dev_kfree_skb_any(skb);
+ skb = skb2;
+ if (!skb)
+ return NULL;
+ }
+
+ __skb_push(skb, DM_TX_OVERHEAD);
+
+ if (pad) {
+ memset(skb->data + skb->len, 0, pad);
+ __skb_put(skb, pad);
+ }
+
+ skb->data[0] = len;
+ skb->data[1] = len >> 8;
+
+ return skb;
+}
+
+static void dm9601_status(struct usbnet *dev, struct urb *urb)
+{
+ int link;
+ u8 *buf;
+
+ /* format:
+ b0: net status
+ b1: tx status 1
+ b2: tx status 2
+ b3: rx status
+ b4: rx overflow
+ b5: rx count
+ b6: tx count
+ b7: gpr
+ */
+
+ if (urb->actual_length < 8)
+ return;
+
+ buf = urb->transfer_buffer;
+
+ link = !!(buf[0] & 0x40);
+ if (netif_carrier_ok(dev->net) != link) {
+ usbnet_link_change(dev, link, 1);
+ netdev_dbg(dev->net, "Link Status is: %d\n", link);
+ }
+}
+
+static int dm9601_link_reset(struct usbnet *dev)
+{
+ struct ethtool_cmd ecmd = { .cmd = ETHTOOL_GSET };
+
+ mii_check_media(&dev->mii, 1, 1);
+ mii_ethtool_gset(&dev->mii, &ecmd);
+
+ netdev_dbg(dev->net, "link_reset() speed: %u duplex: %d\n",
+ ethtool_cmd_speed(&ecmd), ecmd.duplex);
+
+ return 0;
+}
+
+static const struct driver_info dm9601_info = {
+ .description = "Davicom DM96xx USB 10/100 Ethernet",
+ .flags = FLAG_ETHER | FLAG_LINK_INTR,
+ .bind = dm9601_bind,
+ .rx_fixup = dm9601_rx_fixup,
+ .tx_fixup = dm9601_tx_fixup,
+ .status = dm9601_status,
+ .link_reset = dm9601_link_reset,
+ .reset = dm9601_link_reset,
+};
+
+static const struct usb_device_id products[] = {
+ {
+ USB_DEVICE(0x07aa, 0x9601), /* Corega FEther USB-TXC */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x9601), /* Davicom USB-100 */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x6688), /* ZT6688 USB NIC */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x0268), /* ShanTou ST268 USB NIC */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x8515), /* ADMtek ADM8515 USB NIC */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a47, 0x9601), /* Hirose USB-100 */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0fe6, 0x8101), /* DM9601 USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0fe6, 0x9700), /* DM9601 USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x9000), /* DM9000E */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x9620), /* DM9620 USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x9621), /* DM9621A USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x9622), /* DM9622 USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x0269), /* DM962OA USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {
+ USB_DEVICE(0x0a46, 0x1269), /* DM9621A USB to Fast Ethernet Adapter */
+ .driver_info = (unsigned long)&dm9601_info,
+ },
+ {}, // END
+};
+
+MODULE_DEVICE_TABLE(usb, products);
+
+static struct usb_driver dm9601_driver = {
+ .name = "dm9601",
+ .id_table = products,
+ .probe = usbnet_probe,
+ .disconnect = usbnet_disconnect,
+ .suspend = usbnet_suspend,
+ .resume = usbnet_resume,
+ .disable_hub_initiated_lpm = 1,
+};
+
+module_usb_driver(dm9601_driver);
+
+MODULE_AUTHOR("Peter Korsgaard <jacmet@sunsite.dk>");
+MODULE_DESCRIPTION("Davicom DM96xx USB 10/100 ethernet devices");
+MODULE_LICENSE("GPL");
Code Review / kvmfornfv.git / blobdiff