--- /dev/null
+#
+# PHY Layer Configuration
+#
+
+menuconfig PHYLIB
+ tristate "PHY Device support and infrastructure"
+ depends on NETDEVICES
+ help
+ Ethernet controllers are usually attached to PHY
+ devices. This option provides infrastructure for
+ managing PHY devices.
+
+if PHYLIB
+
+comment "MII PHY device drivers"
+
+config AT803X_PHY
+ tristate "Drivers for Atheros AT803X PHYs"
+ ---help---
+ Currently supports the AT8030 and AT8035 model
+
+config AMD_PHY
+ tristate "Drivers for the AMD PHYs"
+ ---help---
+ Currently supports the am79c874
+
+config AMD_XGBE_PHY
+ tristate "Driver for the AMD 10GbE (amd-xgbe) PHYs"
+ depends on (OF || ACPI) && HAS_IOMEM
+ depends on ARM64 || COMPILE_TEST
+ ---help---
+ Currently supports the AMD 10GbE PHY
+
+config MARVELL_PHY
+ tristate "Drivers for Marvell PHYs"
+ ---help---
+ Currently has a driver for the 88E1011S
+
+config DAVICOM_PHY
+ tristate "Drivers for Davicom PHYs"
+ ---help---
+ Currently supports dm9161e and dm9131
+
+config QSEMI_PHY
+ tristate "Drivers for Quality Semiconductor PHYs"
+ ---help---
+ Currently supports the qs6612
+
+config LXT_PHY
+ tristate "Drivers for the Intel LXT PHYs"
+ ---help---
+ Currently supports the lxt970, lxt971
+
+config CICADA_PHY
+ tristate "Drivers for the Cicada PHYs"
+ ---help---
+ Currently supports the cis8204
+
+config VITESSE_PHY
+ tristate "Drivers for the Vitesse PHYs"
+ ---help---
+ Currently supports the vsc8244
+
+config SMSC_PHY
+ tristate "Drivers for SMSC PHYs"
+ ---help---
+ Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs
+
+config BROADCOM_PHY
+ tristate "Drivers for Broadcom PHYs"
+ ---help---
+ Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
+ BCM5481 and BCM5482 PHYs.
+
+config BCM63XX_PHY
+ tristate "Drivers for Broadcom 63xx SOCs internal PHY"
+ depends on BCM63XX
+ ---help---
+ Currently supports the 6348 and 6358 PHYs.
+
+config BCM7XXX_PHY
+ tristate "Drivers for Broadcom 7xxx SOCs internal PHYs"
+ ---help---
+ Currently supports the BCM7366, BCM7439, BCM7445, and
+ 40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
+
+config BCM87XX_PHY
+ tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
+ help
+ Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs.
+
+config ICPLUS_PHY
+ tristate "Drivers for ICPlus PHYs"
+ ---help---
+ Currently supports the IP175C and IP1001 PHYs.
+
+config REALTEK_PHY
+ tristate "Drivers for Realtek PHYs"
+ ---help---
+ Supports the Realtek 821x PHY.
+
+config NATIONAL_PHY
+ tristate "Drivers for National Semiconductor PHYs"
+ ---help---
+ Currently supports the DP83865 PHY.
+
+config STE10XP
+ tristate "Driver for STMicroelectronics STe10Xp PHYs"
+ ---help---
+ This is the driver for the STe100p and STe101p PHYs.
+
+config LSI_ET1011C_PHY
+ tristate "Driver for LSI ET1011C PHY"
+ ---help---
+ Supports the LSI ET1011C PHY.
+
+config MICREL_PHY
+ tristate "Driver for Micrel PHYs"
+ ---help---
+ Supports the KSZ9021, VSC8201, KS8001 PHYs.
+
+config FIXED_PHY
+ tristate "Driver for MDIO Bus/PHY emulation with fixed speed/link PHYs"
+ depends on PHYLIB
+ ---help---
+ Adds the platform "fixed" MDIO Bus to cover the boards that use
+ PHYs that are not connected to the real MDIO bus.
+
+ Currently tested with mpc866ads and mpc8349e-mitx.
+
+config MDIO_BITBANG
+ tristate "Support for bitbanged MDIO buses"
+ help
+ This module implements the MDIO bus protocol in software,
+ for use by low level drivers that export the ability to
+ drive the relevant pins.
+
+ If in doubt, say N.
+
+config MDIO_GPIO
+ tristate "Support for GPIO lib-based bitbanged MDIO buses"
+ depends on MDIO_BITBANG && GPIOLIB
+ ---help---
+ Supports GPIO lib-based MDIO busses.
+
+ To compile this driver as a module, choose M here: the module
+ will be called mdio-gpio.
+
+config MDIO_OCTEON
+ tristate "Support for MDIO buses on Octeon SOCs"
+ depends on CAVIUM_OCTEON_SOC
+ default y
+ help
+
+ This module provides a driver for the Octeon MDIO busses.
+ It is required by the Octeon Ethernet device drivers.
+
+ If in doubt, say Y.
+
+config MDIO_SUN4I
+ tristate "Allwinner sun4i MDIO interface support"
+ depends on ARCH_SUNXI
+ help
+ This driver supports the MDIO interface found in the network
+ interface units of the Allwinner SoC that have an EMAC (A10,
+ A12, A10s, etc.)
+
+config MDIO_MOXART
+ tristate "MOXA ART MDIO interface support"
+ depends on ARCH_MOXART
+ help
+ This driver supports the MDIO interface found in the network
+ interface units of the MOXA ART SoC
+
+config MDIO_BUS_MUX
+ tristate
+ depends on OF_MDIO
+ help
+ This module provides a driver framework for MDIO bus
+ multiplexers which connect one of several child MDIO busses
+ to a parent bus. Switching between child busses is done by
+ device specific drivers.
+
+config MDIO_BUS_MUX_GPIO
+ tristate "Support for GPIO controlled MDIO bus multiplexers"
+ depends on OF_GPIO && OF_MDIO
+ select MDIO_BUS_MUX
+ help
+ This module provides a driver for MDIO bus multiplexers that
+ are controlled via GPIO lines. The multiplexer connects one of
+ several child MDIO busses to a parent bus. Child bus
+ selection is under the control of GPIO lines.
+
+config MDIO_BUS_MUX_MMIOREG
+ tristate "Support for MMIO device-controlled MDIO bus multiplexers"
+ depends on OF_MDIO
+ select MDIO_BUS_MUX
+ help
+ This module provides a driver for MDIO bus multiplexers that
+ are controlled via a simple memory-mapped device, like an FPGA.
+ The multiplexer connects one of several child MDIO busses to a
+ parent bus. Child bus selection is under the control of one of
+ the FPGA's registers.
+
+ Currently, only 8-bit registers are supported.
+
+config MDIO_BCM_UNIMAC
+ tristate "Broadcom UniMAC MDIO bus controller"
+ depends on HAS_IOMEM
+ help
+ This module provides a driver for the Broadcom UniMAC MDIO busses.
+ This hardware can be found in the Broadcom GENET Ethernet MAC
+ controllers as well as some Broadcom Ethernet switches such as the
+ Starfighter 2 switches.
+
+endif # PHYLIB
+
+config MICREL_KS8995MA
+ tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch"
+ depends on SPI
Code Review / kvmfornfv.git / blobdiff